Integrated personal area network (PAN) by way of Bluetooth module (optional) External media cards SD Card Reader supporting MultiMediaCard (MMC) and Secure Digital (SD) Memory Card HP Mini Mobile Drive Bay (on models equipped with a solid-state drive) Internal media cards Two Mini Card slots: Ports Full-size Mini Card slot Half-size Mini Card slot
Audio-in (stereo microphone) Audio-out (stereo headphone) RJ-45 (Ethernet, includes link and activity lights) USB (2) 3-pin AC power
Chapter 1 Product description

Docking

Expansion port Signals passed through expansion port: USB 2.0 Headphone-out/stereo-out and stereo microphone-in VGA-out Power-in Power (up to 50 W)
NOTE: Docking device will support RJ-45 through USB (no pass-through support on the expansion port). Keyboard/pointing device 92% keyboard TouchPad, with 2 TouchPad buttons and 2-way scrolling (taps enabled as default) Power requirements 30-W UMA AC adapter (non-smart) with localized cable plug support AC adapter connector on cable 3-cell lithium-polymer (Li-Pol) battery (2.4-Ah, 26-Wh), 3-hour target life Security Operating system Supports HP Kensington Security Lock Preinstalled: Windows XP Home SP3, ultra low-cost personal computer (ULCPC) edition Restore media: Backup software provided by operating system CD and recovery DVD Serviceability End-user replaceable parts: AC adapter Battery (system) Memory module HP Mini Mobile Drive
External component identification

Top components

Display

Item (1) (2) (3) (4)

Component Internal display switch Speakers (2) Internal microphone Webcam
Function Turns off the display if the display is closed while the power is on. Produce sound. Records and captures sound. Captures still photographs and videos. NOTE: To capture videos, you will need to install additional webcam software.
Chapter 2 External component identification

Wireless antennae

Item (1) (2)
Component WLAN antennae (2) * WWAN antennae (2) (select models only) *
Function Send and receive wireless signals to communicate with wireless local-area networks (WLANs). Send and receive wireless signals to communicate with wireless wide-area networks (WWANs).
* The antennae are not visible from the outside of the device. For optimal transmission, keep the areas immediately around the antennae free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region. To access these notices, click Start > Help and Support > User Guides.

Spare part number 504593-002
HP un2400 Mobile Broadband Module (select models only) Plastics Kit (see Plastics Kit on page 21 for more spare part number information)

483377-002

(9a) (9b) (9c) (9d)
HP Mini Mobile Drive Bay cover Memory module compartment cover SD Card Reader slot bezel Security cable connector For the HP Mini 1000 and Compaq Mini 700 For the red-colored HP Mini 1000 507317-001 512192-001 507707-001 504592-001 507706-001

(10) (11) (12)

RTC battery System board (includes processor and replacement thermal material) Bluetooth module (select models only) NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 507708-001.
Base enclosure (includes 4 rubber feet) For the HP Mini 1000 and Compaq Mini 700 For the red-colored HP Mini 1000 506337-001 512189-001
Memory module (PC2-4200, 533-MHz, DDR2) 512-MB 1024-MB 2048-MB (HP Mini 1000 only) 504599-001 504600-001 517577-001 506336-001

USB board

Item (16)
Description Battery (3-cell, 26-Wh Li-Pol) For the HP Mini 1000 and Compaq Mini 700 For the red-colored HP Mini 1000 (for use in all countries and regions except Germany) For the red-colored HP Mini 1000 (for use in Germany only)
504610-001 512851-001 512851-002
Display assembly components
NOTE: 10.1-inch display assembly components are not sold separately for the HP Mini 1000. The complete display assembly is available as spare part number 509696-001 for the red-colored HP Mini 1000 or 507312-001 for all other models of the HP Mini 1000. NOTE: 10.2-inch display assembly components are not sold separately. The complete display assembly is available as spare part number 512140-001 for the red-colored HP Mini 1000, 507310-001 for all other models of the HP Mini 1000, or 512143-001 for the Compaq Mini 700.
Item (1) (2) (3) Description Speaker grill Speaker assembly (includes left and right cables) Display bezel For use with 8.9-inch panels on the HP Mini 1000 For use with 8.9-inch panels on the Compaq Mini 700 For use with 10.1-inch panels on the Compaq Mini 700 506333-001 509701-001 509704-001 Spare part number 506338-001 506335-001

Item (4)

Description Webcam module NOTE: The webcam module spare part kit does not include a webcam cable. An integrated display/webcam cable for all 8.9-inch panels is included in the Display Cable Kit, spare part number 504597-001 (with WLAN) or 504598-001 (with WWAN). An integrated display/webcam cable for 10.1-inch panels (Compaq Mini 700 only) is included in the Display Cable Kit, spare part number 515208-001 (with WLAN) or 515209-001 (with WWAN). For use with all 8.9-inch panels For use with 10.1-inch panels on the Compaq Mini 700 Display Hinge Kit

Spare part number 504594-001
Webcam module for use with all 8.9-inch panels NOTE: The webcam module spare part kit does not include a webcam cable. An integrated display/webcam cable is included in the Display Cable Kit, spare part number 504597-001 (with WLAN) or 504598-001 (with WWAN).
504595-001 504596-001 504597-001 504598-001 504599-001 504600-001 504601-001 504607-001 504610-001 504611-001 504611-031 504611-041 504611-051 504611-061 504611-071 504611-131 504611-141 504611-161 504611-171 504611-251 504611-281 504611-291 504611-AB1 504611-AD1 504611-B31 504612-001 504613-001 504614-001 504615-001
Display enclosure (includes logo) for use with 8.9-inch panels on the HP Mini 1000 Display Hinge Kit for use with all 8.9-inch panels (includes left/right display hinges and display panel brackets) Display Cable Kit with WLAN for use with all 8.9-inch panels (includes microphone assembly and display/ webcam cable) Display Cable Kit with WWAN for use with all 8.9-inch panels (includes microphone assembly and display/ webcam cable) 512-MB memory module (PC2-4200, 533-MHz, DDR2) 1024-MB memory module (PC2-4200, 533-MHz, DDR2) 60-GB, 4200-rpm hard drive (includes cable and bracket) Hard Drive Hardware Kit 3-cell, 26-Wh Li-Pol battery for the HP Mini 1000 and Compaq Mini 700 Keyboard for use in the United States Keyboard for use in the United Kingdom (Compaq Mini 700 only) Keyboard for use in Germany (Compaq Mini 700 only) Keyboard for use in France (Compaq Mini 700 only) Keyboard for use in Italy (Compaq Mini 700 only) Keyboard for use in Spain Keyboard for use in Portugal (Compaq Mini 700 only) Keyboard for use in Turkey (Compaq Mini 700 only) Keyboard for use in Latin America (HP Mini 1000 only) Keyboard for use in Saudi Arabia (Compaq Mini 700 only) Keyboard for use in Russia Keyboard for use in Thailand (HP Mini 1000 only) Keyboard for use in Japan (HP Mini 1000 only) Keyboard for use in Taiwan (HP Mini 1000 only) Keyboard for use in South Korea (HP Mini 1000 only) Keyboard for international use (Compaq Mini 700 only) Top cover (includes TouchPad) for the HP Mini 1000 and Compaq Mini 700 Rubber Kit (contains 4 device feet and RJ-45 cover) Screw Kit Fan

Spare part number 506333-001 506334-001 506335-001 506336-001 506337-001 506338-001 507309-001 507310-001 507312-001 507313-001 507314-001 507317-001 507318-001 507706-001
Display bezel for use with 8.9-inch panels on the HP Mini 1000 Foil shield for use with all 8.9-inch display panels Speaker assembly (includes left and right cables) USB board Base enclosure (includes 4 rubber feet) for the HP Mini 1000 and Compaq Mini 700 Speaker grill for the HP Mini 1000 and Compaq Mini 700 8.9-inch WSVGA BrightView display assembly for the HP Mini 1000 (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables; WWAN is optional) 10.2-inch, WSVGA, AntiGlare display assembly for the HP Mini 1000 (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables; WWAN is optional) 10.1-inch, standard-definition, AntiGlare display assembly for the HP Mini 1000 (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables; WWAN is optional) 8-GB solid-state drive (includes cable and bracket) 16-GB solid-state drive (includes cable and bracket) Plastics Kit for the HP Mini 1000 and Compaq Mini 700 (see Plastics Kit on page 21 for more Plastics Kit spare part number information) Bracket Kit Bluetooth module NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 507708-001.
507707-001 507708-001 508638-001 509650-001 509650-031 509650-041 509650-051 509650-061 509650-071 509650-131 509650-141 509650-161 509650-171 509650-251 509650-281
RTC battery Cable Kit 8.9-inch WSVGA BrightView display assembly for the Compaq Mini 700 (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables; WWAN is optional) Keyboard for use in the United States (red-colored HP Mini 1000 only) Keyboard for use in the United Kingdom (red-colored HP Mini 1000 only) Keyboard for use in Germany (red-colored HP Mini 1000 only) Keyboard for use in France (red-colored HP Mini 1000 only) Keyboard for use in Italy (red-colored HP Mini 1000 only) Keyboard for use in Spain (red-colored HP Mini 1000 only) Keyboard for use in Portugal (red-colored HP Mini 1000 only) Keyboard for use in Turkey (red-colored HP Mini 1000 only) Keyboard for use in Latin America (red-colored HP Mini 1000 only) Keyboard for use in Saudi Arabia (red-colored HP Mini 1000 only) Keyboard for use in Russia (red-colored HP Mini 1000 only) Keyboard for use in Thailand (red-colored HP Mini 1000 only)

Spare part number 515208-001 515209-001 515210-001 515211-001 515212-001 515213-001
Display Cable Kit with WLAN for use with 10.1-inch panels on the Compaq Mini 700 (includes microphone assembly and display/webcam cable) Display Cable Kit with WWAN for use with 10.1-inch panels on the Compaq Mini 700 (includes microphone assembly and display/webcam cable) Display Rubber Kit for use with 10.1-inch panels on the Compaq Mini 700 Display Screw Kit for use with 10.1-inch panels on the Compaq Mini 700 Foil shield for use with 10.1-inch display panels on the Compaq Mini 700 Webcam module for use with 10.1-inch panels on the Compaq Mini 700 NOTE: The webcam module spare part kit does not include a webcam cable. An integrated display/webcam cable is included in the Display Cable Kit, spare part number 515208-001 (with WLAN) or 515209-001 (with WWAN).

517577-001

2048-MB memory module (PC2-4200, 533-MHz, DDR2) for the HP Mini 1000 only
Removal and replacement procedures
Preliminary replacement requirements

Tools required

You will need the following tools to complete the removal and replacement procedures: Flat-bladed screwdriver Magnetic screwdriver Phillips P0 and P1 screwdrivers

Service considerations

The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures. NOTE: As you remove each subassembly from the device, place the subassembly (and all accompanying screws) away from the work area to prevent damage.

Plastic parts

CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.

Cables and connectors

CAUTION: When servicing the device, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the device. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.

Drive handling

CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the device, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid touching the connector. Handle drives on surfaces covered with at least one inch of shock-proof foam. Avoid dropping drives from any height onto any surface. After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag. Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers. Avoid exposing a drive to temperature extremes or liquids. If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging and label the package FRAGILE.
Chapter 4 Removal and replacement procedures

Grounding guidelines

Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred. An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal cycle. Or the device may function normally for a while, then degrade in the internal layers, reducing its life expectancy. CAUTION: To prevent damage to the device when you are removing or installing internal components, observe these precautions: Keep components in their electrostatic-safe containers until you are ready to install them. Use nonmagnetic tools. Before touching an electronic component, discharge static electricity by using the guidelines described in this section. Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible. If you remove a component, place it in an electrostatic-safe container. The following table shows how humidity affects the electrostatic voltage levels generated by different activities. CAUTION: A product can be degraded by as little as 700 V.

The following grounding equipment is recommended to prevent electrostatic damage: Antistatic tape Antistatic smocks, aprons, and sleeve protectors Conductive bins and other assembly or soldering aids Nonconductive foam Conductive tabletop workstations with ground cords of one megohm resistance Static-dissipative tables or floor mats with hard ties to the ground Field service kits Static awareness labels Material-handling packages Nonconductive plastic bags, tubes, or boxes Metal tote boxes Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material Antistatic plastic Carbon-loaded plastic Metallized laminate Use Bags Floor mats Floor mats Voltage protection level 1,500 V 7,500 V 5,000 V

Unknown user password

If the device you are servicing has an unknown user password, follow these steps to clear the password: NOTE: 1. 2. 3. 4. 5. 6. 7. 8. 9. These steps also clear CMOS.
Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device. Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device. Remove the battery (see Battery on page 37). Remove the real-time clock (RTC) battery (see RTC battery on page 52). Wait approximately 5 minutes. Replace the RTC battery and reassemble the device. Connect AC power to the device. Do not reinsert any batteries at this time. Turn on the device.
All passwords and all CMOS settings have been cleared.
Component replacement procedures
This chapter provides removal and replacement procedures. There are as many as 49 screws, in 7 different sizes, that must be removed, replaced, or loosened when servicing the device. Make special note of each screw size and location during removal and replacement.

Service tag

Device feet
The device feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 504613-001. There are 4 rubber feet that are installed on the base enclosure in the locations illustrated below.

Battery

Description 3-cell, 26-Wh Li-Pol battery for the HP Mini 1000 and Compaq Mini 700 3-cell, 26-Wh Li-Pol battery for the red-colored HP Mini 1000 (for use in all countries and regions except Germany) 3-cell, 26-Wh Li-Pol battery for the red-colored HP Mini 1000 (for use in Germany only) Spare part number 504610-001 512851-001 512851-002
Before disassembling the device, follow these steps: 1. 2. 3. Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device. Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device.
Remove the battery: 1. 2. 3. Turn the device upside down on a flat surface, with the battery bay toward you. Slide the battery release latches (1) to release the battery. Pivot the battery (2) upward and remove the battery from the device (3).
To install the battery, insert the rear edge of the battery into the battery bay and pivot the battery downward until it is seated. The battery release latch automatically locks the battery into place.

Memory module

Description 512-MB (PC2-4200, 533-MHz, DDR2) 1024-MB (PC2-4200, 533-MHz, DDR2) 2048-MB (PC2-4200, 533-MHz, DDR2) (HP Mini 1000 only) Spare part number 504599-001 504600-001 517577-001
Before removing the memory module, follow these steps: 1. 2. 3. 4. Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device. Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device. Remove the battery (see Battery on page 37).
Remove the memory module: 1. Slide the right battery release latch to the inside or unlocked position to reveal the release latch for the memory module compartment cover. Use a thin, narrow tool to slide the release latch to the outside or unlocked position (1). (The edge of the cover rises away from the device.) Remove the cover (2). The memory module compartment cover is included in the Plastics Kit, spare part number 512192-001 for the red-colored HP Mini 1000 or 507317-001 for all other models of the HP Mini 1000 and the Compaq Mini 700.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the device.)
Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot.
Reverse this procedure to install a memory module.

Keyboard

NOTE: For a comprehensive list of spare part numbers, see the Sequential part number listing on page 24.

Lift the rear edge of the top cover (1) and swing it up. Then slide the top cover back slightly to rest against the display assembly (2) at an angle.
Release the ZIF connector (1) to which the TouchPad button board cable is connected.
Disconnect the TouchPad button board cable (2) from the system board, and then remove the top cover.
Reverse this procedure to install the top cover.

WLAN module

Description Broadcom 4312 802.11/b/g WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States Broadcom 4312 802.11/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe Spare part number 504593-001 504593-002

Remove the Bluetooth module: 1. 2. Disconnect the Bluetooth module cable (1) from the system board. Detach the Bluetooth module (2) from the system board. NOTE: The Bluetooth module is attached to the system board with double-sided tape.
Reverse this procedure to install the Bluetooth module.

System board

NOTE: The system board spare part kit includes a processor and replacement thermal material.
Spare part number 504592-001
Description System board equipped with 1.6-GHz processor
Before removing the system board, follow these steps: 1. 2. 3. 4. 5. Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device. Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device. Remove the battery (see Battery on page 37). Remove the following components: a. b. c. Keyboard (see Keyboard on page 40) Hard drive or solid-state drive (see Mass storage devices on page 42) Top cover (see Top cover on page 45)
When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: WLAN module (see WLAN module on page 48) WWAN module, if included (see WWAN module on page 50) RTC battery (see RTC battery on page 52) Bluetooth module (see Bluetooth module on page 53) Heat sink assembly (see Heat sink assembly on page 57)
Remove the system board: 1. 2. Disconnect the wireless antenna cables from the terminals on the WLAN module (see WLAN module on page 48). If the device also includes a WWAN module, disconnect the wireless antenna cables from the terminals on the WWAN module (see WWAN module on page 50).
Disconnect the following cables from the system board: (1) Speaker cables (2) Microphone cable (3) Fan cable (4) Power cable (5) Display panel cable
Remove the two Phillips PM1.62.5 screws (1) that secure the actuators for the power switch and wireless on/off switch to the system board. Remove the actuators (2). NOTE: The actuators are included in the Bracket Kit, spare part number 507318-001.

If it is necessary to replace the display panel brackets, perform the following steps: a. b. Remove the four Phillips PM2.03.0 screws (1) that secure the brackets to the display panel. Remove the brackets (2). The brackets are available in the Display Hinge Kit, spare part number 504596-001 for all 8.9-inch panels or 515207-001 for 10.1-inch panels (Compaq Mini 700 only).
If it is necessary to replace the wireless antenna transceivers and cables, detach the cables from the adhesive that secures them to the display enclosure, and then remove the cables. The wireless antenna transceivers and cables for all 8.9-inch panels are available in the Display Cable Kit, spare part number 504597-001 (with WLAN) or 504598-001 (with WWAN). The wireless antenna transceivers and cables for 10.1-inch panels (Compaq Mini 700 only) are available in the Display Cable Kit, spare part number 515208-001 (with WLAN) or 515209-001 (with WWAN).
Reverse this procedure to reassemble and install the display assembly.

Setup Utility

Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working. The utility reports information about the device and provides settings for startup, security, and other preferences. To start the Setup Utility, turn on or restart the device, and then press f10 while the F10 = BIOS Setup Options message is displayed in the lower-left corner of the screen.

Using the Setup Utility

Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is running, begin at step 2. 1. 2. 3. 4. 5. To open the Setup Utility, turn on or restart the device, and then press f10 while the "F10 = BIOS Setup Options" message is displayed in the lower-left corner of the screen. Use the arrow keys to select System Configuration > Language, and then press enter. Use the arrow keys to select a language, and then press enter. When a confirmation prompt with your language selected is displayed, press enter. To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving Changes, and then press enter.
Your change becomes effective immediately.

Chapter 5 Setup Utility

Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke. To choose a menu or a menu item, use the arrow keys. To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or f5 or f6. To select an item, press enter. To close a text box or return to the menu display, press esc. To display additional navigation and selection information while the Setup Utility is open, press f1.

Displaying system information
The following procedure explains how to display system information in the Setup Utility. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is running, begin at step 2. 1. 2. 3. To open the Setup Utility, turn on or restart the device, and then press f10 while the "F10 = BIOS Setup Options" message is displayed in the lower left corner of the screen. Select the Main menu. System information such as the system time and date and identification information about the device is displayed. To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding Changes, and then press enter.
Restoring default settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not already running, begin at step 1. If the Setup Utility is running, begin at step 2. 1. To open the Setup Utility, turn on or restart the device, and then press f10 while the F10 = BIOS Setup Options message is displayed in the lower-left corner of the screen. Use the arrow keys to select Exit > Load Setup Defaults, and then press enter. When the Setup Confirmation is displayed, press enter. To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving Changes, and then press enter.

2. 3. 4.

The Setup Utility default settings go into effect when the device restarts. NOTE: Your password, security, and language settings are not changed when you restore the factory default settings.
Exiting the Setup Utility
You can exit the Setup Utility with or without saving changes. To exit the Setup Utility and save your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display. Use the arrow keys to select Exit > Exit Saving Changes, and then press enter. To exit the Setup Utility without saving your changes from the current session: If the Setup Utility menus are not visible, press esc to return to the menu display. Use the arrow keys to select Exit > Exit Discarding Changes, and then press enter. After either choice, the device restarts in Windows.

Setup Utility menus

The menu tables in this section provide an overview of Setup Utility options. NOTE: Some of the Setup Utility menu items listed in this chapter may not be supported by your device.

Where used: Two screws that secure the speaker assembly to the display enclosure
Where used: Four screws that secure the display hinges to the display assembly

Phillips PM2.55.0 screw

Length 5.0 mm

Thread 2.5 mm

Head diameter 4.5 mm
Where used: Four screws that secure the display assembly and top cover to the device

Phillips PM2.57.0 screw

Length 7.0 mm
Where used: Four screws that secure the top cover to the base enclosure

Backup and recovery

Backing up your information
NOTE: You can recover only the files that you have previously backed up. HP recommends that you use the Windows backup utility to create a hard drive backup as soon as you set up your device. With the Windows backup utility, you can perform the following tasks: Backing up your information regularly to protect your important system files Creating system recovery points that allow you to reverse undesirable changes to your device by restoring the device to an earlier state Scheduling backups at specific intervals or events
NOTE: The Windows backup utility backs up only data files. The operating system, drivers, and programs are located on the operating system disc and the System Recovery disc that are included with the device.

When to back up

On a regularly scheduled basis NOTE: Set reminders to back up your information periodically.
Before the device is repaired or restored Before you add or modify hardware or software

Backup suggestions

Connect the device to external power before performing backup and recovery procedures. Create system recovery points. Store personal files in the My Documents folder and back up these folders periodically. Back up templates stored in their associated programs. Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document: 1. 2. Display the screen you want to save. Copy the screen image: To copy only the active window, press alt+fn+prt sc. To copy the entire screen, press fn+prt sc. 3. Open a word-processing document and click Edit > Paste. The screen image is added to the document. 4. Save the document.
Backing up individual files or folders
You can back up individual files or folders to an optional external hard drive or to a network drive. NOTE: This process will take several minutes, depending on the file size and the speed of the device.
To back up individual files or folders: 1. Select Start > All Programs > Accessories > System Tools > Backup. The Backup or Restore Wizard page opens. 2. 3. 4. Click Next. Click Backup files and settings, and then click Next. Follow the on-screen instructions.

Product environmental attributes THE ECO DECLARATION
Brand * Company name * Contact information * Internet site * Additional information Hewlett-Packard Hewlett-Packard Company Hans Wendschlag http://www.hp.com/hpinfo/globalcitizenship/environment/contactemail.html http://www.hp.com/hpinfo/globalcitizenship/environment/ Logo
The company declares (based on product specification or test results based obtained from sample testing), that the product conforms to the statements given in this declaration.
Type of product * Model number * Issue date *
Intended market * Additional information

Notebook PC

Compaq Mini 700 - 799 10/28/08 Global Europe Japan U.S. Other
Commercial name * Compaq Mini 700 Series Netbook
This is an uncontrolled copy when in printed form. Please refer to the contact information for the latest version. The declaration may be published only when all rows and/or fields marked with a * are filled-in (n.a. for not applicable).
Quality Control Item QC1 * QC2 * Additional information regarding each item may be found under P14. The company enforces an internal quality control scheme to ensure the correctness of this eco declaration The company is a member of an eco declaration system that enforces regular independent quality control such as organized by IT-Fretagen (see http://www.itforetagen.se).

Requirement met Yes No

Annex B of ECMA-370 2

Edition, December 2006

Page 1 (5)
Model number * Issue date *
Compaq Mini 700 - 799 10/28/08
Product environmental attributes - Legal requirements Item P1 P1.1* P1.2* P1.3* *=mandatory to fill in. Additional information regarding each item may be found under P14. Hazardous substances and preparations Products do not contain lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) as specified in EU 2002/95/EC and its amendments Products do not contain Asbestos (EU 76/769/EEC, amendment 1999/77/EC)
Requirement met Yes No n.a.
Products do not contain Ozone Depleting Substances: Chlorofluorocarbons (CFC), hydrobromofluorocarbons (HBFC), hydrochlorofluorcarbons (HCFC), Halons, carbontetrachloride, 1,1,1-trichloroethane, methyl bromide (EU : Regulation (EC) No. 2037/2000, 2038/2000, 2039/2000) Products do not contain polychlorinated biphenyl (PCB), polychlorinated terphenyl (PCT), (EU 76/769/EEC) Products do not contain short chain chloroparaffins (SCCP) with 10-13 carbon atoms in the chain containing at least 48% per mass of chlorine in the SCCP as specified in Norwegian regulation relating to restrictions on the use of certain dangerous chemicals 20.12.2002 Textile and leather parts with direct skin contact do not contain Tri-(2,3,-dibromopropyl)-phosphate (TRIS), Tris(aziridinyl)-phosphineoxide (TEPA), polybrominated biphenyl (PBB) (EU 76/769/EEC) Textile and leather parts with direct skin contact do not contain Azo colourants that split aromatic amines as specified in EU 76/769/EEC, amendment 2003/3/EC Wooden parts do not contain arsenic and chromium as a wood preservation treatment as well as pentachlorophenol and derivatives (EU 76/769/EEC) Parts with direct and prolonged skin contact do not release nickel in concentrations higher than specified in 76/769/EEC, amendment 94/27/EEC Batteries If hazardous batteries (as defined in 91/157/EEC) are used in the product they are easily removable and labelled with the disposal and the substance logo (as defined in 91/157/EEC, 93/86/EEC) If batteries are used in the product they do not contain mercury in concentrations higher than specified in 91/157/EEC If batteries are permanently installed in the product, information on the environmentally hazardous substances and safe removal method is listed in the user manual (91/157/EEC) Electrical safety, EMC and connection to the telephone network The product meets the Low Voltage Directive (LVD) regarding electrical safety (73/23/EEC & 93/68/EEC) The product meets the EMC Directive regarding electromagnetic compatibility (89/336/EEC / 2004/108/EEC after June, 20th 2007 If product is intended for connection to a public telecom network or contains a radio transmitter, it meets the EU R&TTE Directive (1999/5/EC) The product is CE-marked and a Declaration of Conformity is available (93/68/EEC) Consumable materials If a photo conductor (drum, belt etc.) is used in the product, it does not contain cadmium in concentrations higher than specified in (76/769/EEC and 91/338/EEC) If ink/toner is used in the product, it does not contain cadmium in concentrations higher than specified in (76/769/EEC and 91/338/EEC) If the ink/toner formulation/preparation is classified as hazardous according to EU Directive 1999/45/EC, and as amended, the product/packaging is labelled and a Material Safety Data Sheet (MSDS) in accordance with (99/45/EC & 2001/58/EC) is available. Product packaging The sum of the concentration levels of lead, cadmium, mercury, and hexavalent chromium present in packaging or packaging components does not exceed 0,01% by weight (94/62/EC). Plastic packaging material is marked according to ISO 11469 referring ISO 1043.(97/129/EEC) The product packaging material is free from CFC/HCFC. Treatment information Information for recyclers/treatment facilities (e.g. as requested by 2002/96/EC) is available.

P1.4* P1.5*

P1.6* P1.7* P1.8* P1.9* P2 P2.1* P2.2* P2.3* P3 P3.1* P3.2* P3.3* P3.4* P4 P4.1* P4.2* P4.3*
P5 P5.1* P5.2* P5.3* P6 P6.1*

Page 2 (5)

Product environmental attributes - Market requirements - Environmental conscious design Item *=mandatory to fill in. Additional information regarding each item may be found under P14. P7 Design, Disassembly, recycling P7.1* Parts that have to be treated separately are easily separable P7.2* P7.3* P7.4* P7.5 P7.6* P7.7* P7.8* P7.9. P7.10 P7.11* P7.12* P7.13* P7.14 P7.15 P7.16 P7.17 P7.18 P7.19 P7.20 P8 P8.1* P8.2* P8.3 P9 9.1 Mode On-max Onnormal On-idle Save 1 Save 2 Off 1 Off 2 No load TEC P9.2* P9.3 * * * Plastic materials in covers/housing have no surface coating. Plastic parts >100g consist of one material or of easily separable materials. Plastic parts >25g have material codes according to ISO 11469 referring ISO 1043. Plastic parts are free from metal inlays or have inlays that can be removed with commonly available tools. Labels are easily separable. (This requirement does not apply to safety/regulatory labels). Product lifetime Upgrading can be done e.g. with processor, memory, cards or drives Upgrading can be done using commonly available tools Spare parts are available after end of production for: 3 years Service is available after end of production for: 5 years Material and substance requirements Product cover/housing material type: Material type: ABS Material type: Material type: Electrical cable insulation material of power cables are halogen free (including PVC) Electrical cable insulation material of signal cables are halogen free (including PVC) All cover/housing plastic parts >25g are halogen free All printed circuit boards (without components) >25g are halogen free Chemical specifications of flame retardants in cover / housing plastic parts >25g according ISO 1043-4:
Chemical specifications of flame retardants in printed circuit boards (without components) >25g according ISO 1043-4: Weight of recycled material in plastic parts is 0 Plastic parts >25g are free from flame retardant substances/preparations above 0.1% classified as R45/46, R50/51/53 and R60/61 (67/548/EEC) Light sources are free from mercury If mercury is used specify: Number of lamps: and max. mercury content per lamp: mg Batteries Product does not contain batteries defined as hazardous according to 91/157/EEC Battery chemical composition: Li Ion,Lithium coin Batteries meet the requirements of the following voluntary program/s: Energy consumption For the product the following power levels or energy consumptions have been measured: Power level at Time (s) to <mode> Mode description * Volts W * * W W * W W W W to to to to to to * * * * * *

Reference/ Standard * * * * * * * * *
External power supplies/charger plugged in but disconnected W from the product kWh/y Typical Energy Consumption per year
Information about the energy save function is provided with the product. The product meets the energy requirements of the following voluntary program/s: ENERGY STAR MOU (Ver. 4.0, Tier 1) Others specify:

Page 3 (5)

Product environmental attributes - Market requirements (continued) Requirement met Item * = mandatory to fill in. Additional information regarding each item may be found under P14. Yes No n.a. P10 Emissions Noise emission Declared according to ISO 9296 P10.1 Mode Mode description Declared Declared A-weighted A-weighted sound pressure level LpAm (dB) sound power Operator position Bystander positions level LWAd (B) Desktop or Deskside Idle Operation Other mode Measured according to: P10.2 ISO 7779 Other ECMA-74 (only if not covered by ECMA-74 with LpAm measurement distance m) * Fans on, HDD spinning (if applicable) * Fans on, HDD spinning * 2.6 * 3.26 (only if product is not operator attended)
The product meets the acoustic noise requirements of the following voluntary program/s: Chemical emissions from printing products

P10.3*

Test performed according to ECMA-328 standard The test covers: Dust Ozone
, other specify: Styrene Benzene TVOC
The product meets the chemical emission requirements of the following voluntary program/s: Electromagnetic emissions
P10.5 P11 P11.1* P11.2* P11.3* P12 P12.1* P12.2* P12.3* P13 P13.1* P13.2* P13.3* P13.4*
Computer display meets the requirement for low frequency electromagnetic fields of the following voluntary program/s: Consumable materials for printing products A Material Safety Data Sheet (MSDS) is available for the ink/toner preparation, even if not legally required (see P4.3). Paper containing recycled fibres that meets the requirements of EN12281 can be used. 2-sided (duplex) printing/copying is an integrated product function. Ergonomics for computing products The computer system meets the ergonomic requirements of EN 29241-3, -7, -8 for CRT displays and EN-ISO13406-2 for flat panel displays. The product keyboard meets the requirements of ISO 9995 and EN 29241-4. The computer input device meets the requirements of ISO 9241-9. Packaging and documentation Product packaging material type(s): Polyethylene low density weight (kg): 0.0031 Product packaging material type(s): EPE-Expanded Polyethylene weight (kg): 0.026 Product packaging material type(s): Corrugated carton weight (kg): 0.11141 Product plastic packaging is halogen free (including PVC) User and product documentation do not contain chlorine bleached paper User and product documentation contain recycled paper

Page 4 (5)

P9 9.1
Energy consumption For the product the following power levels or energy consumptions have been measured: Power Consumption AC Input Voltage at 100 VAC +/- 5 VAC, 50 Hz +/- 3 Hz 8.61W Power Consumption AC Input Voltage at 115 VAC +/- 5 VAC, 60 Hz +/- 3 Hz 8.68W Power Consumption AC Input Voltage at 230 VAC +/- 5 VAC, 50 Hz +/- 3 Hz Default Time Settings to Enter Energy Saving Mode Reference Standard (test method)
Power Consumption Mode Description
On-Idle (ENERGY STAR Idle (S0)) ENERGY STAR Sleep (S3) (WOL enabled) ENERGY STAR Standby (Off) (S5) (WOL disabled) ENERGY STAR No-Load

Not Applicable

ENERGY STAR Program Requirements for Computers: Ver. 4.0 ENERGY STAR Program Requirements for Computers: Ver. 4.0 ENERGY STAR Program Requirements for Computers: Ver. 4.0 ENERGY STAR Program Requirements for Single Voltage External Ac-Dc and AcAc Power Supplies

0.852W

0.838W

0.857W

30 minutes (system unit) Not Applicable

0.775W

0.785W

0.778W

P14 Additional information All 1. Product environmental information contained in this declaration is valid as of the date the declaration is published. Changes to sections external standards referenced in the IT Eco-Declaration may invalidate some information contained in this declaration over time. P9 1. Energy efficiency data listed is for an ENERGY STAR compliant product if offered within the model family. HP computers marked with the ENERGY STAR Logo are compliant with the applicable U.S. Environmental Protection Agency (EPA) ENERGY STAR specifications for computers. If a model family does not offer ENERGY STAR compliant configurations, then energy efficiency data listed is for a typically configured model. 2. For more information about HPs ENERGY STAR qualified products, go to hp.com: http://www.hp.com/ and select the applicable market segments and product categories for more information. 3. Energy Efficiency information published on the ECMA 370 The Eco Declaration represents a typically configured product base model meeting ENERGY STAR specifications if offered within the model family. If optional components or modules are added, like extra hard disks or graphic cards etc, these can change the energy efficiency data listed above. 4. Power consumption in the Off / Apparent Off mode is measured and reported with the network interface controller (NIC) WOL disabled. P10 1. Acoustic noise information published on the ECMA 370 The Eco Declaration represents a typically configured product base model only. If optional items with moving parts are added, like extra hard disks or graphic cards with fans etc, these can change acoustic noise values for which HP can take no responsibility.

NOTE: Additional lines may be inserted to declare further items, by positioning the cursor at the far right of the row and hitting the [Enter] key.

Page 5 (5)