Support for one Type II PC Card slots, with support for both 32-bit (CardBus) and 16-bit PC Cards External 65-watt AC adapter with 3-wire power cord 6-cell or 12-cell Li-Ion battery pack Stereo speakers with volume up and down buttons Support for the following optical drives:
8X Max DVD+RW/R and CD-RW Combo Drive 4X Max DVD+RW/R and CD-RW Combo Drive 8X Max DVD-ROM Drive 24X Max DVD/CD-RW Combo Drive

Connectors:

External monitor Universal Serial Bus (USB) v. 2.0 RJ-11 (modem) RJ-45 (network) Audio-out (headphone) Audio-in (microphone) Power IEEE 1394 digital (select models only) S-Video-out (select models only) Infrared (HP Pavilion models only) Parallel Serial Docking (select models only) Digital memory card reader (select models only)
1.2 Resetting the Computer
If the computer you are servicing has an unknown password, follow these steps to clear the password. These steps also clear CMOS: 1. Prepare the computer for disassembly (refer to Section 5.3, Preparing the Computer for Disassembly, for more information). 2. Remove the real-time clock (RTC) battery (refer to Section 5.15, RTC Battery, for more information). 3. Wait approximately 5 minutes. 4. Replace the RTC battery and reassemble the computer. 5. Connect AC power to the computer. Do not reinsert any battery packs at this time. 6. Turn on the computer. All passwords and all CMOS settings have been cleared.

1.3 Power Management

The computer comes with power management features that extend battery operating time and conserve power. The computer supports the following power management features:
Standby Hibernation Setting customization by the user Hotkeys for setting the level of performance Battery calibration Lid switch standby/resume Power/standby button Advanced Configuration and Power Management (ACPM) compliance

1.4 External Components

The external components on the front of the HP Pavilion dv1000 are shown below and described in Table 1-1.
Front Components, HP Pavilion dv1000
Table 1-1 Front Components HP Pavilion dv1000

Component

Speakers (2) Power/standby light

Function

Produces stereo sound.
On: Computer is turned on. Blinking: Computer is in standby. Off: Computer is off.
On or blinking: The internal hard drive or an optical drive is being accessed.
IDE (Integrated Drive Electronics) drive light Battery light
Amber: The battery pack is charging. Green: The battery pack is fully

charged.

Off: The battery pack is discharging
or not inserted. 7 Display release latch Audio-in (microphone) jack Audio-out (headphone) jack (2) Opens the computer. Connects an optional monaural (single sound channel) microphone. Connect optional headphones or powered stereo speakers. Also connect the audio function of an audio/video device such as a television or VCR.

The external components on the front of the HP Compaq nx4800 and Compaq Presario V2000 are shown below and described in Table 1-2.
Front Components, HP Compaq nx4800 and Compaq Presario V2000
Table 1-2 Front Components HP Compaq nx4800 and Compaq Presario V2000
Speakers (2) Wireless button light (select models only) Power/standby light
Produces stereo sound. On: An integrated wireless device is hardware enabled.
On: Computer is turned on. Blinking: Computer is in standby. Off: Computer is off. On or blinking: The internal hard drive
or an optical drive is being accessed.
or not inserted. 8 Display release latch Audio-in (microphone) jack Audio-out (headphone) jack (2 on HP Pavilion dv1000 models) Opens the computer. Connects an optional monaural (single sound channel) microphone. Connect optional headphones or powered stereo speakers. Also connect the audio function of an audio/video device such as a television or VCR.
The external components on the right side of the HP Pavilion dv1000 are shown below and described in Table 1-3.
Right-Side Components, HP Pavilion dv1000
Table 1-3 Right-Side Components HP Pavilion dv1000
USB connectors (2) 6-in-1 Digital Media Reader slot (select models only) 1394 port (select models only) 6-in-1 Digital Media Reader light (select models only) Optical drive S-Video-out jack (select models only)
Connect an optional USB device. In Windows, supports digital memory cards.
Connects an optional 1394a device such as a scanner, digital camera, or digital camcorder. On: A digital memory card is being accessed. Supports an optical disc. Connects an optional S-Video device, such as a television, VCR, camcorder, projector, or video capture card.
The external components on the right side of the HP Compaq nx4800 and Compaq Presario V2000 are shown below and described in Table 1-4.
Right-Side Components, HP Compaq nx4800 and Compaq Presario V2000
Table 1-4 Right-Side Components HP Compaq nx4800 and Compaq Presario V2000
USB connectors (2) 6-in-1 Memory Reader slot (Compaq Presario models only) 6-in-1 Digital Media Reader slot (HP Compaq models only) 1394 port (select models only) 6-in-1 Memory Reader light (Compaq Presario models only) 6-in-1 Digital Media Reader light (HP Compaq models only) Optical drive S-Video-out jack (select models only)

367796-001 367795-001

373053-001 373052-001 394825-001 367771-001 380690-001 383431-001 375979-001 376588-001 367768-001 383876-001 380033-001 367767-001 380032-001
312 Maintenance and Service Guide
System boards (include disk cell RTC battery) 855, for use on full-featured HP Pavilion dv1000 models in countries other than Japan 855, for use on full-featured HP Pavilion dv1000 models in Japan 852GM, for use on full-featured HP Pavilion dv1000 models in Japan For use on HP Pavilion dv1000 models with Intel Pentium M processors For use on HP Pavilion dv1000 models with Intel Celeron M processors For use on HP Compaq nx4800 and Compaq Presario V2000 models with Intel Pentium M processors For use on Compaq Presario V2000 models with Intel Celeron M processors PC Card assemblies Silver with 1-dot PC Card eject lever Black with 3-dot PC Card eject lever Black with 1-dot PC Card eject lever
381062-001 391884-001 381063-001 367799-001 367800-001 373522-001 373523-001
385869-001 389524-001 389525-001
USB/S-Video controller boards For use on HP Pavilion dv1000 models and HP Compaq nx4800 and Compaq Presario V2000 models with a 1394 port, S-Video-out jack, expansion port, and digital memory card reader For use only on Compaq Presario V2000 models without a 1394 port, S-Video-out jack, expansion port, and Memory Reader 367794-001

373533-001

Menu control button board (includes bracket and cable, for use only on HP Pavilion dv1000 computer models) Speaker assemblies For use on HP Pavilion dv1000 models For use on HP Compaq nx4800 and Compaq Presario V2000 models

373535-001

367793-001 374625-001
Base enclosures For use on HP Pavilion dv1000 models For use on HP Compaq nx4800 and Compaq Presario V2000 models 367763-001 367764-001
Battery packs 12-cell, 8.8-AHr 6-cell, 4.4-AHr 6-cell, 4.0-AHr 367760-001 367759-001 398065-001
Optical drives (include bezel) For use on HP Pavilion dv1000 models 8X DVD-ROM Drive 24X DVD/CD-RW Combo Drive 4X DVD+RW/R and CD-RW Combo Drive 4X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive, LightScribe 8X DVDRW/R and CD-RW Dual Layer Combo Drive 367789-001 367790-001 373625-001 375981-001 375983-001 383877-001 383896-001
316 Maintenance and Service Guide
Optical drives (Continued) For use on HP Compaq nx4800 and Compaq Presario V2000 models 8X DVD-ROM Drive 24X DVD/CD-RW Combo Drive 4X DVD+RW/R and CD-RW Combo Drive 4X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive, LightScribe 8X DVDRW/R and CD-RW Dual Layer Combo Drive
373524-001 373525-001 373626-001 375982-001 375984-001 383878-001 389897-001
Hard drives (include frame and connector) 5400-rpm 80-GB 60-GB 4200-rpm 100-GB 80-GB 60-GB 40-GB 377651-001 375980-001 381721-001 367788-001 367787-001 367786-001
Mini PCI communications cards 802.11b/g Broadcomm (for use in most of the world) 802.11b/g Broadcomm (for use in the rest of the world) 802.11b/g Broadcomm (Japan, for use only on HP Compaq nx4800 models) 802.11b Intel (for use in most of the world) 802.11b Intel (for use in the rest of the world) 802.11b/g Intel (for use in most of the world) 802.11b/g Intel (for use in the rest of the world) Bluetooth Wireless LAN

359118-001 364727-001 338796-001

3.5 Miscellaneous

Table 3-4 Spare Parts: Miscellaneous (not illustrated)
Description Logo Kits For use on HP Pavilion dv1000 models For use on HP Compaq nx4800 models For use on Compaq Presario V2000 models Wired headset with volume control Personal Video Recorder HP remote control (for use only on HP dv1000 computer models) USB travel mouse 65-watt AC adapter 373058-001 373530-001 373059-001 371693-001 352950-001 371694-001 309674-001 371790-001 Spare Part Number
Screw Kit (includes the following screws; refer to Appendix C, Screw Listing, for more information on screw specifications and usage) For use on HP Pavilion dv1000 models For use on HP Compaq nx4800 and Compaq Presario V2000 models 367776-001 373534-001
Phillips PM2.54.0 screw Phillips PM2.04.0 screw Phillips PM2.07.0 round head screw Phillips PM2.03.0 screw Phillips PM2.07.0 screw Phillips PM1.52.0 screw Phillips PM2.05.0 screw
Table 3-4 Spare Parts: Miscellaneous (not illustrated) (Continued)
Description Power cords For use in: Australia and New Zealand Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden Canada, French Canada, Latin America, Taiwan, Thailand, and the United States Denmark Hong Kong and the United Kingdom Israel Italy Japan Korea The Peoples Republic of China Switzerland Taiwan 373979-011 373979-021 373979-001 373979-081 373979-031 373979-BB1 373979-061 373979-291 373979-AD1 373979-AA1 373979-111 373979-AB1 Spare Part Number
3.6 Sequential Part Number Listing
Table 3-5 Spare Parts: Sequential Part Number Listing
Spare Part Number 309674-001 352950-001 359118-001 364727-001 367759-001 367760-001 367761-001 367762-001 Description USB travel mouse Personal Video Recorder USB diskette drive USB digital drive Battery pack, 6-cell, 4.4-AHr Battery pack, 12-cell, 8.8-AHr Top cover for use on HP Pavilion dv1000 models (includes TouchPad) Top cover for use on Compaq Presario V2000 models with a 1394 port, S-Video-out jack, expansion port, and Memory Reader (includes TouchPad) Base enclosure for use on HP Pavilion dv1000 models Base enclosure for use on HP Compaq nx4800 and Compaq Presario V2000 models Miscellaneous Plastics Kit for use on HP Pavilion dv1000 models Miscellaneous Plastics Kit for use on HP Compaq nx4800 and Compaq Presario V2000 models Processor, Intel Celeron M 330 (1.4-GHz) with 400-MHz FSB (includes thermal pad) Processor, Intel Celeron M 340 (1.5-GHz) with 400-MHz FSB (includes thermal pad) Processor, Intel Pentium M 725 (1.6-GHz) with 400-MHz FSB (includes thermal pad)
367763-001 367764-001 367765-001 367766-001 367767-001 367768-001 367771-001

367795-001 367796-001 367797-001 367798-001 367799-001 367800-001 371693-001
Spare Part Number 371694-001 371790-001 373023-001 373024-001 373025-001 373026-001 373047-001 373048-001 373052-001 373053-001 373054-001 373055-001 373058-001 373059-001 373060-001 Description HP remote control (for use only on HP dv1000 computer models) 65-watt AC adapter Mini PCI communications card, 802.11b Intel (for use in most of the world) Mini PCI communications card, 802.11b Intel (for use in the rest of the world) Mini PCI communications card, 802.11b/g Intel (for use in the rest of the world) Mini PCI communications card, 802.11b/g Intel (for use in most of the world) Mini PCI communications card, 802.11b/g Broadcomm (for use in most of the world) Mini PCI communications card, 802.11b/g Broadcomm (for use in the rest of the world) Processor, Intel Pentium M 735 (1.7-GHz) with 400-MHz FSB (includes thermal pad) Processor, Intel Pentium M 745 (1.8-GHz) with 400-MHz FSB (includes thermal pad) Display assembly, 14.0-inch, WXGA, SVA with Brightview for use on HP Pavilion dv1000 models Display assembly, 14.0-inch, WXGA, SVA with Brightview for use on Compaq Presario V2000 models Logo Kit for use on HP Pavilion dv1000 models Logo Kit for use on Compaq Presario V2000 models Display assembly, 14.0-inch, WXGA, SVA with Brightview for use on HP Compaq nx4800 models
Spare Part Number 373061-001 373522-001 Description Mini PCI communications card, 802.11b/g Broadcomm (Japan) System board for use on HP Compaq nx4800 and Compaq Presario V2000 models with Intel Pentium M processors System board for use on Compaq Presario V2000 models with Intel Celeron M processors 8X DVD-ROM Drive for use on HP Compaq nx4800 and Compaq Presario V2000 models 24X DVD/CD-RW Combo Drive for use on HP Compaq nx4800 and Compaq Presario V2000 models Display assembly, 14.0-inch, WXGA, SVA for use on HP Compaq nx4800 models Top cover for use on HP Compaq nx4800 models (includes TouchPad) Logo Kit for use on HP Compaq nx4800 models Top cover for use on Compaq Presario V2000 models without a 1394 port, S-Video-out jack, expansion port, and Memory Reader (includes TouchPad) Switch cover for use on Compaq Presario V2000 models without wireless (includes wireless button and light) USB/S-Video controller board for use only on Compaq Presario V2000 models without a 1394 port, S-Video-out jack, expansion port, and Memory Reader Screw Kit for use on HP Compaq nx4800 and Compaq Presario V2000 models Menu control button board (includes bracket and cable, for use only on HP Pavilion dv1000 computer models)
373523-001 373524-001 373525-001 373528-001 373529-001 373530-001 373531-001

Spare Part Number 382078-001 383431-001 385869-001 383876-001 383877-001 383878-001 389524-001 389525-001 389896-001 389897-001 391884-001 394186-001 395825-001 398065-001 Description Left and right display hinge covers and brackets for use on HP Compaq nx4800 and Compaq Presario models Processor, Intel Pentium M 715 (1.5-GHz) with 400-MHz FSB (includes thermal pad) PC Card assembly, silver, with 1-dot PC Card eject button Processor, Intel Celeron M 370 (1.5-GHz) with 400-MHz FSB (includes thermal pad) 8X DVDRW/R and CD-RW Combo Drive, LightScribe, for use on HP Pavilion dv1000 models 8X DVDRW/R and CD-RW Combo Drive, LightScribe, for use on Compaq Presario V2000 models PC Card assembly, black, with 3-dot PC Card eject button PC Card assembly, black, with 1-dot PC Card eject button 8X DVDRW/R and CD-RW Dual Layer Combo Drive for use on HP Pavilion dv1000 models 8X DVDRW/R and CD-RW Dual Layer Combo Drive for use on Compaq Presario V2000 models 855 system board for use on full-featured HP Pavilion dv1000 models in Japan EMI Gasket Kit for use on all models Processor, Intel Pentium M 725A (1.6-GHz) with 400-MHz FSB (includes thermal pad) 6-cell, 4.0-AHr battery pack
Removal and Replacement Preliminaries
This chapter provides essential information for proper and safe removal and replacement service.

4.1 Tools Required

You will need the following tools to complete the removal and replacement procedures: Magnetic screwdriver Phillips P0 screwdriver 5.0-mm socket for system board screwlocks Flat-bladed screwdriver Tool kitincludes connector removal tool, loopback plugs, and case utility tool
4.2 Service Considerations
The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures.
As you remove each subassembly from the computer, place the subassembly (and all accompanying screws) away from
the work area to prevent damage.

Plastic Parts

Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.

Cables and Connectors

CAUTION: When servicing the computer, ensure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Ensure that cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.

4.6 Workstation Precautions
Use the following grounding precautions at workstations: Cover the workstation with approved static-shielding material (refer to Table 4-2, Static-Shielding Materials). Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. Use conductive field service tools, such as cutters, screwdrivers, and vacuums. When using fixtures that must directly contact dissipative surfaces, only use fixtures made of static-safe materials. Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and Styrofoam. Handle electrostatic-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items only at static-free workstations. Avoid contact with pins, leads, or circuitry. Turn off power and input signals before inserting or removing connectors or test equipment.
4.7 Grounding Equipment and Methods
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm 10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap. When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground. To be effective, the conductive strips must be worn in contact with the skin. Other grounding equipment recommended for use in preventing electrostatic damage includes: Antistatic tape Antistatic smocks, aprons, and sleeve protectors Conductive bins and other assembly or soldering aids Nonconductive foam Conductive tabletop workstations with ground cords of one megohm resistance Static-dissipative tables or floor mats with hard ties to the ground Field service kits Static awareness labels Material-handling packages Nonconductive plastic bags, tubes, or boxes Metal tote boxes Electrostatic voltage levels and protective materials
Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
Table 4-1 Typical Electrostatic Voltage Levels

wireless antenna cable is attached to Make note of whichon the Mini PCI communications card which antenna clip before disconnecting the cables. 5. Disconnect the wireless antenna cables 1 from the Mini PCI communications card. 6. Spread the two retaining tabs 2 that secure the Mini PCI communications card to the communications compartment socket. (The board rises up). 7. Remove the wireless communications card 3 by pulling the board away from the socket at a 45-degree angle.
Removing a Mini PCI Communications Card
Reverse the above procedure to install a Mini PCI communications card.

5.8 Optical Drive

Optical Drive Spare Part Number Information
For use on HP Pavilion dv1000 models 8X DVD-ROM Drive 24X DVD/CD-RW Combo Drive 4X DVD+RW/R and CD-RW Combo Drive 4X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive, LightScribe 8X DVDRW/R and CD-RW Dual Layer Combo Drive For use on HP Compaq nx4800 and Compaq Presario V2000 models 8X DVD-ROM Drive 24X DVD/CD-RW Combo Drive 4X DVD+RW/R and CD-RW Combo Drive 4X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive 8X DVDRW/R and CD-RW Combo Drive, LightScribe 8X DVDRW/R and CD-RW Dual Layer Combo Drive 367789-001 367790-001 373625-001 375981-001 375983-001 383877-001 383896-001
2. Remove the PM2.07.0 screw 1 that secures the optical drive to the computer. 3. Insert a thin tool, such as a paper clip, into the media tray release hole 2. (The optical drive media tray releases from the optical drive.) 4. Use the media tray frame to slide the optical drive 3 out of the computer. 5. Remove the optical drive.
Removing the Optical Drive
Reverse the above procedure to install an optical drive.

5.9 Switch Cover

Switch Cover Spare Part Number Information
For use on HP Pavilion dv1000 models with wireless capability For use on HP Pavilion dv1000 models without wireless capability For use on HP Compaq nx4800 and Compaq Presario V2000 models with a 1394 port, S-Video-out jack, expansion port, and Memory Reader with wireless capability For use on HP Compaq nx4800 and Compaq Presario V2000 models with a 1394 port, S-Video-out jack, expansion port, and Memory Reader without wireless capability For use on Compaq Presario V2000 models without a 1394 port, S-Video-out jack, expansion port, and Memory Reader 367781-001 367780-001 367782-001
1. Prepare the computer for disassembly (Section 5.3). 2. Position the computer with the rear panel toward you.
HP Pavilion dv1000 models. Steps 3 through 9 apply only tosection for information on See steps 10 through 14 in this removing the switch cover on HP Compaq nx4800 and Compaq Presario V2000 models.
3. Remove the three PM2.04.0 screws that secure the switch cover to the computer.
Removing the Switch Cover Screws, HP Pavilion dv1000 models Only

4. Turn the computer display-side up with the front panel toward you. 5. Open the computer as far as possible. 6. Insert a flat-blade screwdriver 1 under the outside edges of the display hinge covers. 7. Lift the outside edges of the hinge covers 2 until the switch cover disengages from the computer.
Releasing the Switch Cover, HP Pavilion dv1000 models Only
8. Swing the rear edge of the switch cover forward.
Removing the Switch Cover, HP Pavilion dv1000 models Only
9. Remove the switch cover.
through only to Steps 10 Presario 14 applymodels. HP Compaq nx4800 and Compaq V2000 10. Remove the two PM2.04.0 screws that secure the switch cover to the computer.
Removing the Switch Cover Screws, HP Compaq nx4800 and Compaq Presario V2000 models Only
11. Turn the computer display-side up with the front panel toward you. 12. Open the computer as far as possible. 13. Insert a flat-blade screwdriver into the slots located behind the F1, F5, F11, and insert keys 1 and lift the front edge of the switch cover 2 until it disengages from the computer. 14. Remove the switch cover.
Removing the Switch Cover, HP Compaq nx4800 and Compaq Presario V2000 models Only
Reverse the above procedure to install the switch cover.

5.10 Keyboard

Keyboard Spare Part Number Information
For use on HP Pavilion dv1000 models in: Asia Pacific, Australia, Hong Kong, the Peoples Republic of China, and the United States Belgium Denmark France French Canada Germany Greece Israel Italy 367778-001 Korea Latin America Europe and the Netherlands Norway Portugal Saudi Arabia Spain Sweden/Finland Switzerland Taiwan Thailand United Kingdom 367778-AD1 367778-161 367778-331 367778-091 367778-131 367778-171 367778-071 367778-B71 367778-111 367778-AB1 367778-281 367778-031 3677777-291
367778-A41 367778-081 367778-051 367778-121 367778-041 367778-DJ1 367778-BB1 367778-061
For use on HP Compaq nx4800 models in Japan For use on Compaq Presario V2000 models in: Asia Pacific, Australia, Hong Kong, the Peoples Republic of China, and the United States Denmark Europe and the Netherlands France French Canada 367777-001 Italy Korea Latin America Norway Sweden/Finland Spain Taiwan Thailand The United Kingdom

2. Remove the optical drive (Section 5.8). 3. Remove the switch cover (Section 5.9). 4. Close the computer. 5. Turn the computer upside down with the rear panel toward you.
Steps 6 through 11 applyinonly to HP Pavilion dv1000 models. See steps 12 through 15 this section for information on
removing the keyboard on HP Compaq nx4800 and Compaq Presario V2000 models. 6. Remove the two PM2.04.0 screws that secure the keyboard to the computer.
Removing the Keyboard Screws, HP Pavilion dv1000 models Only
7. Turn the computer display-side up with the front panel toward you. 8. Open the computer as far as possible. 9. Lift the rear edge of the keyboard and swing it forward until it rests on the palm rest.
Releasing the Keyboard, HP Pavilion dv1000 models Only
10. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board.
Disconnecting the Keyboard Cable, HP Pavilion dv1000 models Only

11. Remove the keyboard.

through only to Steps 12 Presario 15 applymodels. HP Compaq nx4800 and Compaq V2000 12. Remove the four PM2.03.0 screws 1 that secure the keyboard to the computer. 13. Swing the rear edge of the keyboard 2 up and forward until it rests on the palm rest.
Releasing the Keyboard, HP Compaq nx4800 and Compaq Presario V2000 models Only
14. Release the ZIF connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board.
Disconnecting the Keyboard Cable, HP Compaq nx4800 and Compaq Presario V2000 models Only
15. Remove the keyboard. Reverse the above procedure to install the keyboard.

5.11 Display Assembly

Display Assembly Spare Part Number Information
For use on HP Pavilion dv1000 models 14.0-inch, WXGA, SVA with Brightview 14.0-inch, WXGA For use on HP Compaq nx4800 models 14.0-inch, WXGA, SVA with Brightview 14.0-inch, WXGA For use on Compaq Presario V2000 models 14.0-inch, WXGA, SVA with Brightview 14.0-inch, WXGA Left and right display hinge covers and brackets For use on HP Pavilion dv1000 models For use on HP Compaq nx4800 and Compaq Presario models 373054-001 367783-001 373060-001 373528-001 373055-001 367784-001 382077-001 382078-001
1. Prepare the computer for disassembly (Section 5.3). 2. Remove the memory module compartment (Section 5.6) and Mini PCI compartment covers (Section 5.7).
3. Disconnect the wireless antenna cables from the Mini PCI communications card.
Disconnecting the Wireless Antenna Cables

2. Remove the two PM2.07.0 screws that secure the base enclosure to the computer
Removing the Base Enclosure Screws, Part 1, HP Pavilion dv1000 models Only
3. Turn the computer upside down with the front panel toward you. 4. Remove the following: 1 Fourteen PM2.07.0 screws 2 One PM2.05.0 screw 3 Two PM2.04.0 screws
Removing the Base Enclosure Screws, Part 2, HP Pavilion dv1000 models Only
5. Swing the rear edge of the base enclosure 1 straight up and forward until it rests at an angle. 6. Slide the base enclosure 2 back at an angle. 7. Remove the base enclosure.
Removing the Base Enclosure, HP Pavilion dv1000 models Only
Steps 8 and 9 apply only to HP Compaq nx4800 and Compaq Presario V2000 models.
8. Remove the following: 1 Fifteen PM2.07.0 screws 2 Three PM2.04.0 screws 9. Lift the base enclosure 3 straight up and remove it.
Removing the Base Enclosure, HP Compaq nx4800 and Compaq Presario V2000 models Only
Reverse the above procedure to install the base enclosure.
5.13 USB/S-Video Controller Board
USB/S-Video Controller Board Spare Part Number Information
For use on HP Pavilion dv1000 models and HP Compaq nx4800 and Compaq Presario V2000 models with a 1394 port, S-Video-out jack, expansion port, and digital memory card reader For use only on Compaq Presario V2000 models without a 1394 port, S-Video-out jack, expansion port, and Memory Reader 367794-001
Hard drive (Section 5.4) Optical drive (Section 5.8) Switch cover (Section 5.9) Keyboard (Section 5.10) Display assembly (Section 5.11) Base enclosure (Section 5.12)
2. Remove the two PM2.04.0 screws 1 that secure the USB/S-Video controller board to the top cover. 3. Lift the right side of the board 2 to disconnect it from the system board. 4. Remove the USB/S-Video controller board.
Removing the USB/S-Video Controller Board
Reverse the above procedure to install the USB/S-Video controller board.

5.14 Speaker Assembly

Speaker Assembly Spare Part Number Information
For use on HP Pavilion dv1000 models For use on HP Compaq nx4800 and Compaq Presario V2000 models 367793-001 374625-001
2. Disconnect the speaker cable 1 from the system board. 3. Lift the speaker 2 and remove it from the top cover.
Removing the Speaker Assembly
Reverse the above procedure to install the speaker assembly.

5.15 RTC Battery

is included with the system board. Refer The RTC batterySystem Board, for more information. to Section 5.20, 1. Prepare the computer for disassembly (Section 5.3) and remove the following components:
2. Remove the RTC battery from the socket on the system board.

Removing the RTC Battery

Reverse the above procedure to install the RTC battery.
544 Maintenance and Service Guide

3-Conductor Power Cord Set Requirements (Continued)
Country Korea The Netherlands Norway Peoples Republic of China Sweden Switzerland Taiwan United Kingdom United States Accredited Agency EK KEMA NEMKO CCC SEMKO SEV BSMI BSI UL Applicable Note Number 2
1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used. 2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration. 3. The appliance coupler, flexible cord, and wall plug must bear a T mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration. 4. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used. 5. The flexible cord must be Type RVV, 3-conductor, 0.75 mm conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.

Screw Listing

This appendix provides specification and reference information for the screws used in the computer. All screws listed in this appendix are available in the Miscellaneous Screw Kits, spare part numbers 367776-001 (for use on HP Pavilion dv1000 models) and 373534-001 (for use on HP Compaq nx4800 and Compaq Presario V2000 models).
Table C-1 Phillips PM2.05.0 Screw

Head Width 4.0 mm

Color Black

Qty. 10

Length 5.0 mm

Thread 2.0 mm

Where used: 1 Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C clips; documented in Section 5.4) 2 Two screws that secure the memory module compartment cover to the computer (screws are captured on the cover by C clips; documented in Section 5.6) 3 One screw that secures the Mini PCI compartment cover to the computer (screw is captured on the cover by C clips; documented in Section 5.7)

network jack location 115, 117 pin assignments A2 network, troubleshooting 228 Next/Fast Forward button 125 nonfunctioning device, troubleshooting 214, 225 num lock key 119, 121 num lock light 127, 129
OK button 127 operating system loading, troubleshooting 215 optical drive location 111, 113, 132, 134 OS loading problems 220 precautions 42 removal 516

Index5

QuickPlay, no OS loading 221, 222
rear components 114, 116 remote control, spare part number 325, 332 removal preliminaries 41 procedures 51 replacement preliminaries 41 procedures 51 right-side components 110, 112 RJ-11 (modem) jack location 115, 117 pin assignments A5 RJ-45 (network) jack location 115, 117 pin assignments A2 RTC battery, removal 544
Screw Kit, spare part number 325, 328, 333 screw listing C1 security cable slot 115, 117 serial number 31, 52 service considerations 41 speaker assembly removal 542 spare part numbers 315, 331, 334, 542
speakers 17, 19 specifications battery pack 65 computer 61 display 63 DMA 616 DVD+RW/R and CD-RW Combo Drive 68 DVD/CD-RW Combo Drive 66 DVDRW/R and CD-RW Combo Drive 610, 612 DVD-ROM drive 614 hard drive 64 I/O addresses 619 interrupts 617 memory map 622 static shielding materials 47 Stop button 125 S-Video-out jack location 111, 113 pin assignments A3 switch cover removal 518 spare part numbers 35, 330, 333, 518 system board removal 554 spare part numbers 313, 331, 333, 335, 336, 554 system memory map 622

Index6

tools required 41 top components 122, 124, 126, 128, 130 top cover, spare part numbers 39, 327, 333 TouchPad buttons 127, 131 horizontal scrolling region 131 light 127, 131 location 127, 131 on/off button 127, 131 vertical scroll region 127, 131 transporting precautions 44 troubleshooting audio 223 Computer Setup 21 docking device 214 flowcharts 25 keyboard 226 modem 228 network 228 no OS loading for QuickPlay application 221, 222 nonfunctioning device 214, 225 OS loading 215 overview 21 pointing device 227 power 28 video 212
Universal Serial Bus (USB) connector location 111, 113, 115, 117 pin assignments A1 USB digital drive, spare part number 324, 327 USB diskette drive, spare part number 327 USB pocket drive, spare part number 324 USB travel mouse, spare part number 325, 327 USB/S-Video controller board removal 540 spare part numbers 313, 331, 333, 540
video recorder, spare part number 325, 327 video troubleshooting 212 volume buttons 125, 129
Windows applications key 119, 121 Windows logo key 119, 121 wireless button 125, 129 wireless button light 19 wireless light 114, 129 workstation precautions 45

Index7

HP-00007-01, Appendix 3

13-Oct-2004

Appendix 3 Product End-of-Life Disassembly instructions Product Identification: Marketing Name / Model Compaq Presario V2000 Series Notebook PC Description Notebook PC
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions for the disassembly of HP products to remove components and materials requiring selective treatment. 1.0 Items Requiring Selective Treatment 1.1 Items listed below are classified as requiring selective treatment. 1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as applicable. Item Description Notes Quantity of items included in product. Printed Circuit Boards (PCB) or Printed Circuit Assemblies (PCA) Batteries With a surface greater than 10 square cm All types including standard alkaline and lithium coin or button style batteries For example, mercury in lamps, display backlights, scanner lamps, switches, batteries Includes background illuminated displays with gas discharge lamps 1 2
Mercury containing components
Liquid Crystal Displays (LCD) with a surface greater than 100 square cm Cathode Ray Tubes (CRT) Capacitors / condensers (Containing PCB / PCT) Electrolytic Capacitors / Condensers measuring greater than 2.5 cm in diameter or height External electrical cables and cords Gas Discharge Lamps Plastics containing Brominated Flame Retardants Components and parts containing toner and ink, including liquids, semi-liquids (gel/paste) and toner Components and waste containing asbestos Components, parts and materials containing refractory ceramic fibers
Declaration limited to case plastics only. Include the cartridges, print heads, tubes, vent chambers, and service stations. 0 0

Page 1

Components, parts and materials containing radioactive substances
Tools Required List the type and size of the tools that would typically be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description Screwdriver Screwdriver Screwdriver Tool Size (if applicable) Type-cross #1 Type-cross #0 Type-T #8
Product Disassembly Process List the basic steps that should typically be followed to remove components and materials requiring selective treatment: 15 Remove 8 or 12 cell main battery. Remove two M2.5*6L screws on HDD door and HDD, then remove two M2.5*6L and HDD module. Remove one M2.5*6L screws on lower case, then remove ODD module. Remove four M2.5*14L screws on logic lower and then remove keyboard cover. Remove two M2.5*6L and four M2.5*6L screws, then remove LCD module Remove four M2.5*3L then remove keyboard. Reverse it back and remove eleven M2.5*14L screws and five M2.5*6L screws on logic lower then disassemble logic lower. Remove four spring screws on thermal module, then remove thermal module on M/B. Remove seven M2.5*6L screws, then remove thermal frame. Remove four M2.5*6L screws, remove M/B. Remove RTC coin cell battery on M/B for selective treatment Remove two M2.5*4L on audio board, then remove audio board. Remove six M2.5*4L screws on trackpad board, then remove trackpad module. Remove four M2.5*6L screws on LCD module, then disassemble LCD bezel from LCD module, then remove LCD module. Remove mercury bulb from LCD assy for selective treatment
OPTIONAL: Depending upon the complexity of the disassembly process, a graphic depicting the locations of items contained within the product which require selective treatment (with descriptions and arrows identifying locations) can be inserted below:

Page 2

Page 3