ELECTRONIC ENGINEERING LTD.

PowerWave-4

4 zone Control panel Communicator
User's Operating and Programming Guide

Version 8.69

P/N 7121346 Rev. D N.A

May 2003

Contents

Introduction.... 5

Meet the Crow Alarm Control System.. 5 Typical Alarm System Configuration.. 5

Keypad Description... 5

Function Keys... 5 Alphanumeric Keys... 6 Audible Signals.. 6 Indicators.... 7 Summary of Functions... 7

Operation... 8

How to Arm the System before Exit.. 8 How to Arm the System when Staying Home. 9 How to Arm Partitions.. 10 How to Bypass Zones... 10 How to use Chime (If enable by Installer).. 10 Emergency Alerts.. 11 Generate Threat or Duress.. 11 How to Read System Messages... 11 How to Read Trouble Messages.. 12 How to Display Events from Memory.. 12 How to Control Outputs and Devices.. 14 How to Get into to User Program/Client Mode.. 14 How to Change or Add Codes.. 14 How to Change Master Code.. 15 How to Add or Change User Code. 15 How to Delete User Code.. 15 3
How to Add or Change Telephone Numbers.. 15 How to set Time and Date.. 16 How to operate the access control output. 16 How to start Walk test Mode.. 16 How Remote command control works.. 17

Warranty.. 19

Introduction
Meet the Crow Alarm Control System
Thank you for choosing to protect your premises with a PowerWave-4 of Crow Electronic Engineering Ltd. PowerWave of Crow Electronic Engineering Ltd. is a highly advanced, multifunction alarm control system, designed to flawlessly manage your security system at home or at business, protects you against burglary and supports the operation of electronic devices.
Typical Alarm System Configuration
The protected premises can be divided up to 4 zones, as defined by the installation scheme. The protected area can be grouped into 2 separate partitions (A and B). The system can be grouped for User s convenience to separate, in a business environment, the offices from the warehouse area, or in a private residence, the different rooms of the home, e.g., living room, bedroom, etc. Each zone can react differently to various events, to generate an alarm or activate a device. The system can be armed in two different modes: 1) Arm the protected areas are entirely vacated 2) Stay people and pets populate the protected areas. The User who has access to the keypad's control features, can change the settings. The system can be accessed via multiple keypads (each located at a different site). Up to 8 keypads can be integrated into the system. Access levels and Users access codes are detailed below.

Keypad Description

The LED Keypad shows all the information required to operate the system. The User communicates with the alarm system via the keypad. The Keypad displays continuous information about the status of the alarm system, and enables the User to operate the system in different modes, change settings and program Users' access codes. The keypad also collects and records events to be displayed afterward on request, to overview system activities, and to analyze system performance for diagnostics.

Function Keys

These keys are used to arm the system, enter commands to alter system settings, or scroll through the history events. ARM , STAY , BYPASS , PROGRAM ,CONTROL , MEMORY , PANIC , ENTER
Ready-Byp System Trouble Program

L TRO C ON

MEMORY

PAN IC

BYPASS

PROGRAM

Alphanumeric Keys
These keys are used to enter codes, Initiate Emergency or for programming.

Audible Signals

The keypad emits signals (beeps) in response to User activities. These signals are listed in Table. Table: List of Audible Signals Sound Short beep 3 short beeps Long beep Slow beeping Sequence Once only Once only Once only Through the Exit or Entry delay time Description A key in the keypad has been pressed Operation carried out successfully Illegal operation, or wrong key pressed Exit or entry delay warning when arming the system indicates that you must exit the protected area, also Entry delay warning when entering via the entry zone, to disarm the system.

Indicators

There are 14 LEDs indicators show the status of the system. Zone indicators LEDs 1- 4 Partitions indicators LEDs A, B Status indicators LEDs 5 8. Ready Byp indicator , System indicator. Trouble indicator , Program indicator.

Summary of Functions

The system's main functions are listed in table Function Full or Partition Arm Full Arm Disarm during exit Disarm Arm Stay Keys Description

! CODE ! ! !

Initiates full arm
Initiates full arm Disarms the system during exit delay
Only if enabled by installer Only when slow beeping is emitted Stopping Alarms Only if enabled by installer

! CODE ! ! ! !

STAY ENTER
Disarms the system Initiates partial alarm when the user is home Initiates partial alarm when the user is home

! CODE

Arm Stay
Disarm Stay Disarm Stay Bypass

! CODE ! ! ! ! ! !

Disarms the system Disarms the system

! Zone #

Bypasses a zone(s)
Repeats the procedure to un-bypass zones
Initiate Panic Initiate Panic

Activates panic alert

Activates emergency alert
Only if enabled by installer
Function Initiate Medical Initiate Fire Alarm Memory

Description

Notes Only if enabled by installer Only if enabled by installer Displays events, and automatically scrolls to the next event every 2.5 sec. (Use <MEMORY> key to scroll up manually) Only if enabled by installer Press <Control> for 2 seconds
Activates emergency alert Activates emergency alert Initiates display of events from memory. <ENTER> cancels memory readout
Chime Enable/dis able Control

! ! ! ! !

CONTROL
Enable or disable chime function Activates or deactivates outputs and devices Activates program mode to add or change Users' codes

Device#

Change or Add Users' code

! M CODE

For details see page 12
If you started an operation incorrectly, press <ENTER> to exit and return to the previous mode.

Operation

How to Arm the System before Exit
Preparing the System for Arming Verify that the green <Ready Byp> indicator is lit.This indicator is lit only when all zones are closed (all doors, exits and windows are closed and motion in the protected area is restricted or bypassed) , the system is ready to be armed. If the green <Ready Byp > indicator is not illuminated, the zone LED 1 to 4 is lit displays the open zones. Close open zones, or bypass them. Bypass any zone you cannot close , the Byp> indicator flashes indicating bypassed zone(s). For details see page 9. Note: Bypassed zones are not protected. <Ready

Arming the System

Before leaving premises the system has to be armed. When the system is Ready , indicator is lit , enter user code and then <ENTER> to arm the system. There is a exit delay prior to the system being armed. During this delay time, a slow beeping is heard to indicate that the system is not armed yet and reminds you to leave the protected area. The A indicator lights up to indicate that the system is armed. (The indicators may go out few seconds after exit delay expired installer's setting). If you must disarm the system during the exit delay, press <ARM>. Quick Arm (When enabled by the installer) , depending on the

When the system is Ready , press <ARM> to arm the system. The A indicator lights up to indicate that the system is armed. During exit delay time, a slow beeping is heard to indicate that the system is not armed yet and reminds you to leave the protected area.

Disarming the System

Enter Users code and press <ENTER>. The A indicator goes off to indicate that the system is disarmed. Stopping Alarms
Enter Users code and press <ENTER> to stop alarm any time.
How to Arm the System when Staying Home
Arming the System in Stay Mode This type of arming is used when people are present within the protected area. At night time, when the family is about to retire , perimeter zones are protected, but not the interior zones. Consequently, interior movements will be ignored by the system. When the system is Ready, press <STAY> , enter user code, and then <ENTER>. The A indicator flashes to indicate that the system is armed in stay mode. Quick Stay When enabled by the installer, press <STAY> to arm the system.
During exit delay you can leave the premises. If you wish to stay or that no one will enter the protected premises, you may cancel the Entry/exit delay by pressing the <ENTER> key. The slow beeping stops and the system is immediately armed. The A indicator flashes to indicate that the system is armed in stay mode. (The indicators may go out a few seconds after exit delay expired , depending on the installer's setting).
Enter users code and press <ENTER>, or press <STAY> if enabled by installer. The A indicator goes off to indicate that the system is disarmed.

How to Arm Partitions

The protected area can be grouped into two separate partitions ( A and B ). The system can be grouped for User s convenience to separate, in a business environment, the offices from the warehouse area, or in a private residence, the different rooms of the home, e.g., living room, bedroom, etc. To arm partition A enter user code for partition A To arm partition B enter user code for partition B, Note: to arming partition with code see page 7 How to arm the system before exit During exit delay you can leave premises. At the end of the procedure the A indicator or the B indicator lights up to indicate that the partition A or/and B is armed. (The indicators may go out after a few seconds, depending on the installer's setting). To disarm partition, see "Disarming the System".

How to Bypass Zones

Bypass any zone that cannot be closed. You can bypass selected zones prior to arming. It is also used to temporarily exclude a faulty zone from service, which requires repair. To bypass a selected zone, press <BYPASS>, the Ready Byp indicator and program indicator lights up to indicate that the system is in bypass mode. Enter the zone number one or more zones ,the zone LED indicators lights up to indicate that the zone is bypassed ,following press <ENTER> , the Ready Byp LED flashes to indicate zone(s) bypassed. To un-bypass, press <BYPASS>, enter zone number, and <ENTER>. Note: Disarming automatically un-bypasses zones.
How to use Chime (If enable by Installer)
A Chime (Day zone) is a detector that can be part armed while you are at home but working in another part of the building. It can be programmed to operate a buzzer or light to let you know you have a visitor. To disable this function, press <CONTROL> , Program LED and System LED indicators lights up, press the <PROGRAM> , Program LED flashes to indicate that Chime is disabled.
To enable Chime mode press <CONTROL> and <PROGRAM> again Program LED goes off to indicate that Chime is enabled.

Emergency Alerts

This special keys function is best programmed by your installer to suit your individual situation. Most commonly it is used in a panic situation to sound only the outside siren and perhaps call a monitoring station. How to initiate Panic
Press the <PANIC> or Press simultaneously <1>and <3>. How to initiate Medical Alarm
Press simultaneously <7> and <9>. How to initiate Fire Alarm
Press simultaneously<4> and <6>.
Generate Threat or Duress
If you are compelled to disarm the system under threat, you must enter the duress digit before the users code to activate the automatic dialer. The duress digit shifts up your usual code by one digit. If your code is 345 and 8 is your duress digit, than entering 8345 will modify your code. The modified duress code will disarm the system in a normal way, but at the same time will activate the dialer silently to report a duress event without arousing suspicion. (For details ask installer.)
How to Read System Messages

When viewing the memory events at the keypad by pressing the <MEMORY>,the first thing that will always be displayed is the system messages. If the system led turns ON but no other Zone LEDs are ON at the same time, this means that there are no current system alarms. If a zone LED and LEDs are ON then this indicates system alarms that have not yet cleared. The LEDs 1-8 are pre-defined as to what system alarm they will display. These system alarm indications are shown in the table below. Following the display of current system alarms the panel will then sequence through the 127 historical memory events starting at the most recent event. The second table shows the alarm events that can be displayed in memory mode and what indicators are used to show them.
LED # 1 LED # 2 LED # 3 LED # 4
Battery Low Mains Failure Telephone Line Failure Radio Detector Battery Low
LED # 5 Radio Pendant Battery Low LED # 6 Supervised Detector Failure LED # 7 Zone Inactivity Timeout LED # 8 Dialer Kiss-off Failure
How to Read Trouble Messages
Any failure or abnormal events that may occur are indicated by trouble messages, and the Trouble indicator is lit. Press <MEMORY> to read out messages and other events stored in memory.
How to Display Events from Memory
The system memory stores the last events. Press <MEMORY> to display list of events. Following the display of current system alarms the panel will then sequence through
the 127 historical memory events starting at the most recent event. The second table shows the alarm events that can be displayed in memory mode and what indicators are used to show them. The system will display the last event and automatically scroll to the next one every 2.5 seconds, and a beep is emitted. Use the arrow keys to scroll up manually. Wait until all messages are displayed, or press <ENTER> to cancel memory readout.

EVENT TYPE

DEVICE

INDICATOR

STATUS

ACTIVATION BYPASS

Zones 1-4 Zones 1-4
LED's 1-4 Ready Byp LED's 1-4
On Steady On Steady On Steady Flashing On Steady Flashing On Steady Flashing
DETECTOR TAMPER (SHORT CIRCUIT) DETECTOR TAMPER (OPEN CIRCUIT) CABINET TAMPER

Zones 1-4

Trouble LED's 1-4

Trouble LED's 5-8

Cabinet or Satellite Siren

Trouble

Siren LOW BATTERY Controller Battery System LED 1 MAINS FAILURE Controller Mains Supply SYSTEM LED 2 LED's 1-4 Trouble LED's 1-8 PANIC BUTTON (or BUTTONS 1&3 PRESSED TOGETHER) FIRE ALARM (BUTTONS 4&6 PRESSED TOGETHER) MEDICAL ALARM (BUTTONS 7&9 PRESSED TOGETHER) PENDANT PANIC Keypad Panic System On Steady On Steady On Steady On Steady Flashing On Steady Flashing Flashing
RADIO ZONE LOW BATTERY Radio PIR Zone 1-4 PENDANT LOW BATTERY Radio Key User 1-8

Keypad Fire

System AREA A
Flashing Flashing Flashing Flashing Flashing Flashing On Steady On Steady Flashing Flashing On Steady Flashing On Steady Flashing Flashing On Steady On Steady On Steady On Steady On Steady

Keypad Medical

System AREA B

Radio Key User 1-4

System LED 1-4 AREA A AREA B AREA A AREA B Trouble AREA A & B
ARMED A ARMED B STAY MODE A STAY MODE B DURESS ALARM
Area A is Armed Area B is Armed Area A STAY Mode ON Area B STAY Mode ON Duress Alarm

SUPERVISED RADIO ALARM

Supervised Radio Passive Infra-Red

System Trouble LEDs 1-4

ZONE INACTIVITY ALARM
Ready Byp Trouble LEDs 1-4

TELEPHONE LINE FAILURE

Phone Line Failure

Trouble LED 3

How to Control Outputs and Devices
The keypad enables control of external devices, such as an air-conditioner or heater. To activate or halt a device, press <CONTROL> , Program and System LEDs lights up steady , press the number of the device , up to 8 different devices can be controlled via the keypad ,then press <ENTER> to activate or deactivate the selected device. To check what outputs are ON simply press the <CONTROL> key , LEDs corresponding to device ON lights up.Press <ENTER> to return to normal mode.
How to Get into to User Program/Client Mode
There are 2 levels of program mode, CLIENT mode and INSTALLER mode. Normally the installer will give you access to the CLIENT mode so you can add, delete, or change the user codes. If you request it your installer can provide you with access to the INSTALLER mode as well. To get into CLIENT mode provided the system is NOT armed Press <PROGRAM> enter Master code and <ENTER>. The Program indicator lights up to indicate that the system is in User programming mode. If you get a single long beep at this point and the Program LED doesnt turn on, it means your code cannot access Program mode. How to exit program mode

To exit out of program mode press <PROGRAM> and <ENTER>. The Program indicator goes off to indicate that the system is not in User programming mode.
How to Change or Add Codes
About Master code and User code The factory default master code (123) is intended as a preliminary control of the alarm system. After PowerWave is installed and put into service, the code can be changed to any code known to the Master user. The Master user can define up to 9 user codes. To limit access rights, the holder of the Master code can ask the installer to define several User profiles. Access rights are listed below: User code has Area A and/or B permission User code can arm and/or disarm arm an area User code can arm and/or disarm arm an area in Stay mode User code can change its code User code can change users code User code can change dialer telephone numbers
User code can alter the real time clock
How to Change Master Code
While in client mode ,Press <PROGRAM> and 1 to change Master code press <ENTER>, the code digit will be flashed back to you. Use the numeric keyboard to enter your new Master code. The code can hold any combination of 1 to 6 digits. It is recommended using a multi-digit code. Press <ENTER> to save your new code , the new code will be flashed to you and 3 short beeps to indicate correct entry or 1 long beep if not accepted. Press <PROG> and <ENTER> exit user Code Program mode.
How to Add or Change User Code
While in client mode, press <PROGRAM> and the User number (2 to 10) to add or change the code ,press <ENTER>. If there is an existing code already, it will be flashed back to you. Use the numeric keyboard to enter the new code. The code can hold any combination of 1 to 6 digits. Entering the new code will delete the old code. Press <ENTER> to save your new code , the new code will be flashed to you and 3 short beeps. Repeat the procedure for all users. Press <PROG> and <ENTER> to exit Local Program mode.

How to Delete User Code

While in client mode, press <PROGRAM> and the User number (2 to 10) you intend to delete, press <ENTER>. The code will be flashed back to you. Press <BYPASS> to delete User code. Press <ENTER> to save the change. Press <PROG> and <ENTER> exit program mode.
How to Add or Change Telephone Numbers
Your panel will accept up to 4 phone numbers with a total of 16 digits. Your panel can be programmed to dial all or any of these depending on the event which has occurred.(The 4 phone numbers are at program address 501 through to 504). While in CLIENT mode, key in the following sequence <PROGRAM> <501> <ENTER> (The address for telephone number 1), The existing number will be flashed out at the Keypad then enter <NEW TELEPHONE #> <ENTER> The new numbers will be flashed back to confirm acceptance. At any time you can enter in the address for the telephone number just to view the currently programmed value then press the <PROGRAM> button to move on to another address. Note: Address 501 = PH # 1, 502 = PH# 2 to 504 = PH# 4. (Note: on the LED keypad 0 is indicated by LED A and 9 by LED B)

How to set Time and Date

The alarm system has an internal clock that used to identify when events occurred in memory via the LCD keypad. Should you need to change the Time & Date it must be done from CLIENT mode. To change the Time & Date press Press <PROGRAM> <403> <ENTER> <1-7> <ENTER> Where 1-7 = the current day (1=Sun, 2 = Mon to 7 = Sat) Press <PROGRAM> <401> <ENTER> <HHMM> <ENTER> Where HH = Hour in 24 Hour Format and MM = Minutes
Press <PROGRAM> <405> <ENTER> <1-31> <ENTER> Where 1-31 = the current date Press <PROGRAM> <406> <ENTER> <1-12> <ENTER> Where 1-12 = the current month Press <PROGRAM> <407> <ENTER> <YY> <ENTER> Where YY = current year, e.g. 02=2002
How to operate the access control output
If the alarm system has been set up to allow control of an electric door lock, you can activate the door release function as follows; Press <CONTROL> or Press <CONTROL> enter CODE then <ENTER> The Control LED will lights up while the lock is active and turn off as soon as power is removed from the lock. The Access Control function can either be a single button operation or restricted to requiring a valid User code entry. Both options are shown above. Please consult your installer as to what option may be programmed.
How to start Walk test Mode
While in CLIENT mode a User with the proper authority can start walk-test mode. This special mode latches the alarm signals from detectors at the keypad initiating the test so that one person can trigger every detector connected to the alarm then return to the keypad to verify operation. On terminating Walk-test mode the test results are put into the memory buffer so they can be viewed at a later time. To start Walk-test mode while in CLIENT mode press <PROGRAM> <627> <ENTER> The keypad buzzer will beep at 1-second intervals
Next trigger every detector connected to the panel then return to the keypad and all of the zones that were triggered will be displayed at the keypad. To terminate Walk-test mode press <ENTER>
How Remote command control works
Another powerful feature available from your alarm is Command Control. This feature is a remote control facility which allows valid users to access the panel via a standard touch tone telephone and check or change the Arm/Disarm status of each of the areas, operate each of the eight outputs or turn on an optional Microphone. The Command Control feature is only available on panels fitted with a Voice or DTMF board. The Voice board provides voice prompts to guide you through Command control operations whereas the DTMF board provides tones (one Long Tone for ON or three short beeps for OFF). Please talk to your installer to find out if all or any of these options are available on your alarm. To perform any of the Command Control features you must first ring the phone number, which the panel is connected to. The panel may be set up to answer after a specific number of rings of it may be set-up to use a fax defeat option. Either way, when you ring the phone number and the panel answers the call, the first thing you will hear over the phone is a burst of modem tone for two seconds. After this tone has stopped you must enter the access code, which is associated with the Command menu option you wish to access. Remember, the code you enter will determine which menu option you access. If you miss the pause, the panel will repeat the modem tone and then again pause for 5 seconds looking for your access code. This process will be repeated 4 times before hanging up if no valid code is received. When entering codes or other information in Command Control the "#" key acts as a "Clear" button.

When you have entered the required 4-digit access code the panel will reply with the status message associated with the Command Control function you have accessed. For example, lets say we have a code of 2045 to allow Arming & Disarming of Area A. Once the code 2045 has been received the panel checks the current status of Area A and replies with the pre-programmed voice message relating to that status e.g. if Area A is Armed then the Armed message will be sent, if Disarmed then the Disarmed message will be sent. If only the DTMF board is fitted, the voice message is substituted with a long beep if Area A is Armed, and three short beeps if it is disarmed. Once the status message has informed you of the actual state, you can use the "*" key to toggle the option on & off or Arm and Disarm, e.g. in our example above, code 2045 accesses Area "A" arming or disarming. Assuming the status message we received was "Area A alarm is Armed" If we press the "*" key, Area "A" will be Disarmed and we would receive a status message "Area A alarm is Disarmed" (or whatever message is programmed by the installer) While you are on-line with the panel you can move between menu options by entering the code of the option you want to control. Assuming there was a code of 4321 programmed to control outputs. After having used code 2045 to control the Arm/Disarm status of Area A we first press the # button to reset all previous entries. Then we can enter the digits 43215 (that is 4321 as the code to control outputs and 5 to select output #5). The current status of output #5 will be given either by the voice message or the appropriate
tone and then the status can be changed with the * button on the remote telephone (Note; For output control you must enter in the 4 digit code e.g. 4321 followed by the output number you wish to control, in this case 5). At any stage, if you enter in an incorrect code you can press the # button on the remote telephone to clear all code entries and then start again.
To turn on the optional Microphone (only available if the Voice Board is fitted) you must enter in the appropriate code followed by the * button. To turn the Microphone off you simply press the * button again. To end a Command Control session simply hangs up the phone. The panel is monitoring the line at all times and 15 seconds after the last key press it will automatically hang up the line. This 15-second timer is active during the whole command control process so a period of 15 seconds without a key press will cause the panel to hang-up.

Warranty

CROW LIMITED WARRANTY (Crow) warrants this product to be free from defects in materials and workmanship under normal use and service for a period of one year from the last day of the week and year whose numbers are printed on the printed circuit board inside his product. Crows obligation is limited to repairing or replacing this product, at its option, free of charge for materials or labor, if it is proved to be defective in materials or workmanship under normal use and service. Crow shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other then Crow. There are no warranties, expressed or implied, of merchantability or fitness for a particular purpose or otherwise, which extend beyond the description on the face hereof. In no case shall Crow be liable to anyone for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever, even if the loss or damage is caused by Crows own negligence or fault. Crow does not represent that this product can not be compromised or circumvented; that this product will prevent any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that this product will in all cases provide adequate warning or protection. Purchaser understands that a properly installed and maintained product can only reduce the risk of burglary, robbery or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result. Consequently, Crow shall have no liability for any personal injury, property damage or any other loss based on claim that this product failed to give any warning. However, if Crow is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause or origin, Crows maximum liability shall not in any case exceed the purchase price of this product, which shall be the complete and exclusive remedy against Crow.
Use the following form to record your changes and customizations. User Name Out Device Designation Zone Zone Name

www.thecrowgroup.com

support@crow.co.il

Addressing new LCD Keypads
Addressing new Icon Keypads

D C B A

Off On

Keypad 1

D Keypad 1 Keypad 2 Keypad 3 Keypad 4 Keypad 5 Keypad 6 Keypad 7 Keypad 8
default C On On On On Off Off Off Off
B On On Off Off On On Off Off
A On Off On Off On Off On Off
Keypad 1 Keypad 2 Keypad 3 Keypad 4 Keypad 5 Keypad 6 Keypad 7 Keypad 8 Panel PW-4
Switch '1' Switch '2' Switch '3' Off Off Off On Off Off Off On Off On On Off Off Off On On Off On Off On On On On On Switch '5' Switch '6' Switch '7' Off Off Off On Off On Off Switch '8' On Off Off On On Off Off Off Off On
PW-8 PW-16 PW-64 (Ver1.01) PW-64 (Ver1.04+) Disable Tamper Enable Tamper Page 10

Tamper Enable

Tamper Disable
Dip-Switch 4 & 8 MUST Always be ON
FUNCTIONS The PowerWave LED Keypad consists of; an 18 button, backlit silicone rubber keypad, 14 LED indicators and an internal piezo buzzer housed in a modern white plastic housing. The plastic housing has a hinged front lid to cover and protect the rubber buttons when not in use. All the electronics are contained on a single circuit board inside the housing. Because the keypads communicate with the controller using data, the cable run from panel to keypads is secure against tampering. For this reason there is no tamper switch on the keypad assembly. Access to the keypad electronics will not disarm the panel. BUTTONS The 18 silicone rubber buttons are used for the following functions. In normal operating mode the numeric keys are used for entering Access Codes. In Program Mode the numeric keys are used for entering options & new values. The buttons with text labels are used as function buttons and select the options indicated by the text and normally precede other button presses, e.g. to enter Bypass Mode press <BYPASS> and the numeric key corresponding to the zone number you wish to be excluded.
The PROGRAM Key is used to prefix option selections in the program modes e.g. <PROGRAM> 4 <ENTER> selects User Code 4. The PROGRAM key is also used prior to a Master Code to enter user program mode from normal operation mode.
The ENTER Key is used to enter access or program codes. It is normally used at the end of a button sequence. The CONTROL button, if enabled, is used to isolate day zone audible alarms if temporarily not required and/or to directly control outputs if programmed. LED INDICATORS The LED indicators are used to display system conditions including Zone status, Battery state, Tamper etc. Please refer to the LED table on page 10 for a full explanation of the conditional displays.
INSTALLING WIRELESS RECEIVERS

RX-40:

The PowerWave-8 is fully compatible with the new RX-40 Wireless receivers. The addition of this receiver will add wireless capability to your system in the form or wireless PIR detectors, Wireless Remote Controls/Medical Pendants, Wireless Reed Switches and Wireless Smoke Detectors. The Receiver connects to the same communications port as the keypads and can be installed either inside the cabinet, or if preferred, may be installed at a remote location. The Receiver is available in 3 frequencies, 303.875mhz, 433.92mhz or 27mhz. Multiple receivers can be added to the system to gain better reception if needed. The receiver requires 4 cores and can successfully be run in 0.2mm unscreened cable over a distance of up to 100 metres. Like the keypads the Receiver has 12v connections labelled POS and NEG which are wired to the 12v supply and CLK and DATA terminals for connection to the communications bus. The green LED fitted to the receiver will indicate when the unit is in "Learn" mode (Flashing - see address 601) or when it is receiving an actual wireless transmission (On Steady).

Freewave:

The Freewave receiver is compatible with the Power Wave-8 panel Ver: 8.64 and above and requires a 4 wire connection to the Power Wave-8 panel PCB. This can be achieved by using the 5 pin wiring loom connector (5th (Yellow - Listen-In) wire Not required) to plug into the loom socket on the Power Wave-8 panel PCB, or to the data buss screw terminals. Loom wire connections are: Red=(Pos +)12v, Black=(Neg -)12v, Green=Clock, Blue=Data. Page 11
PROGRAMMING YOUR PowerWave-8
ACCESS TO PROGRAMMING ON POWER UP (INSTALLER MODE) When power is applied to the controller for the first time, with the panel tamper input open, the panel will inhibit tamper alarms and ready the panel to enter INSTALLER PROGRAM Mode (unless the Installer Lock-out option Address 170 option 2 has previously been enabled). At this point you can go to any keypad which is connected to the panel and press PROGRAM ENTER which will automatically put that keypad into full Program mode, Program LED Flashing. (NOTE: Only one keypad can be in Program mode at any time)
ACCESS TO PROGRAMMING Before you can enter Installer Programming, the panel must not be armed. Press <PROGRAM> - < Installer Code> - <ENTER> Program light will Flash Note: Default Installer Code (Code 11) is 000000. You are now in Installer Programming Mode. Any program addresses may be viewed or changed in this mode. HOW TO PROGRAM The programming sequence always follows this pattern; <PROGRAM> - <1,2 or 3 digit address> - <ENTER> 3 short beeps if OK - 1 long beep if error The LEDS will display current value or status Enter the new value or option <New Value> - <ENTER> 3 short beeps if OK - 1 long beep if error Access to Installer programming mode can be restricted by having to enter Client Programming mode first. This is done at Address 169 option 3. USER CODE PROGRAMING BY CLIENT Press <PROGRAM> - <Master Code> - <ENTER> Program light On Steady Note: Default Master Code is 123 (Address 1). You are now in Client Program Mode. Only User Codes 1-10 can be viewed or changed in this mode. Codes may be denied access to Client mode, allowed access to change their code only or allowed access to view & change all user codes. RESETTING BACK TO FACTORY DEFAULT SETTINGS (From Install Mode Only) This address allows you to reset the panel back to the factory defaults (Reset All defaults). e.g.To reset All System defaults including User Codes, go to Address 620 Press <PROGRAM> - 620 - <ENTER> 3 beeps - Program light flashing After the system configuration has been reset back to defaults, all values, options & Codes will be set to the values shown in the Program Option Summary as defaults. These value & option selections have been chosen as the most common set-up for the majority of systems. Address 621-625 allow selective defaults to be set (refer to program summary at the back of the manual for more details).

<A.Z>

Press the corresponding Alpha-Numeric key to replace the current digit. (Just like making a text message on a mobile phone) <MEM> toggles between upper and lower case. <ENTER> saves the text <A> returns back the last saved text <B> returns back the default text Below are the functions of the Alpha-Numeric keys: Button # 1st Press * () A (a) D (d) G (g) J (j) M (m) P (p) S (s) V (v) 2nd Press # (<) B (b) E (e) H (h) K (k) N (n) Q (q) T (t) W (w) Y (y) 3rd Press = (>) C (c) F (f) I (i) L (l) O (o) R (r) U (u) X (x) Z (z) 4th Press 9 0
PROGRAMMING ZONE DESCRIPTIONS
Zone #1 TEXT (maximum 16 characters) Zone #2 TEXT Zone #3 TEXT Zone #4 TEXT Zone #5 TEXT Zone #6 TEXT Zone #7 TEXT Zone #8 TEXT Page 15

Zone 1

Samanthas Room
PROGRAMMING AREA CHARACTER
998 Area Character (maximum of 1 per Area) Areas <A.Z>
ABCDEFGHIJKLMNOP The Power Wave-8 LCD keypad allows you to re-name both Areas (Areas A & B) that the Power Wave-8 provides. Therefore, at program address P998E, you can re-name the Areas 1 & 2 (instead of the default Area names of A, B).

PROGRAMMING PANEL NAME

999 Panel Name Display (maximum 16 characters) Name PowerWave 8 <A.Z>
ADJUSTING KEYPAD BACKLIGHT LEVEL
Backlighting of the Keys and the LCD Display can be adjusted in 16 steps from Fully illuminated to Off. Increase LCD Backlight - Hold <CONTROL> and press <STAY> repeatedly Decrease LCD Backlight - Hold <CONTROL> and press <BYPASS> repeatedly Increase Keypad Backlight - Hold <CONTROL> and press <MEM> repeatedly Decrease Keypad Backlight - Hold <CONTROL> and press <> repeatedly

ADJUSTING BUZZER TONE

The Keypad Buzzer tone can be adjusted in 16 steps from fully On to Off. Increase Volume - hold <CONTROL> and press <A> repeatedly Decrease Volume - hold <CONTROL> and press <B> repeatedly
PROGRAMMING OPTIONS Output States
NOTE: With all output programming options we refer to outputs 1-8. Only outputs 1-4 are available as standard, with outputs 5-8 requiring the connection of the optional 4 way output expander unit that connects to the keypad bus ( the output expander provides 4 change-over relay contacts). Addresses 31-38 are used to map output modifiers to each of the 8 outputs available on the PowerWave-8. Addresses 31-38 In this block, address 31 relates to Output #1, 32 relates to Output #2 etc Address 31

Invert output - Default = Off Flash output - Default = Off Single pulse to output - Default = Off Lockout output once reset - Default = Off Siren Driver to output - Default = Off Control button can operate output - Default = Off Output flashes on a 24 hour zone alarm - Default = Off Day zones linked to pulse timer - Default = Off

Option

Invert Output - This option is used to invert the normal state of the output. The Alert uses open collector type transistor switches and the default state of all outputs is off or high. When in alarm the transistor switch is turned on and the output is switched low. The invert option reverses this function. Flash Output - This option causes the output to turn on and off at a rate set by the pulse timer for this output (Address 221-228) when in alarm and is normally used to flash a lamp during an activation. Single Pulse to Output - This option, when applied, produces a single pulse at the output during an alarm (the pulse time is the value programmed at the output pulse timer address, 221-228). Page 16

Option Option

Lockout Once Reset - This option is used to limit the output to one operation per arming period. Siren Driver to Output - This option causes the output to be a modulated output designed to drive 8 ohm 10 watt horn speakers directly. Outputs 1 & 2 can have the siren driver feature. A different tone is generated at output 1 to that at outputs 2. NOTE: DO NOT CONNECT A HORN SPEAKER TO OUTPUT 1 or 2 WITHOUT FIRST TURNING THIS OPTION ON OTHERWISE DAMAGE MAY OCCUR TO THE OUTPUT CONCERNED. Control button can operate output - The Control button on the keypad can be used to turn outputs on or off. For this to happen this option must be turned on for the output/s concerned. To turn an output on the operator simply presses the Control button at which time the System & Program LEDs will illuminate to indicate that the Control mode is active. If any controllable outputs are currently on, the relevant green zone led (LEDS 1-8) will be on. The operator can now press a button relating to the output/s they wish to control eg pressing the 1 button will turn output 1 on or off, The 2 button for output 2 etc. When an output state is changed the zone LED will indicate the change of state. When finished the operator then presses the Enter button to cancel the Control mode and return to normal. Output Pulses for 24 hour alarms - If a 24 hour zone activates the alarm this option will cause the output to flash at a rate equal to the value set for the pulse timer (Address 221-228). Chime Zones Linked to Pulse Timer - Chime Zones programmed to this output will pulse at the pulse timer rate (Address 221-228) for the duration of the Chime zone to output timer (Address 211218)
Address 32 - 38 as per Address 31 above but for Outputs 2-8

24-Hour Output Options

Address 41 - 48 In this block, address 41 relates to output #1, 42 relates to output #2 etc Address 41 (For Output #1) Remote Control Panic to Output - Default = On Keypad Panic to Output - Default = On Keypad Fire to Output - Default = On Keypad Medical to Output - Default = Off Cabinet Tamper to Output - Default = On Duress Alarm to Output - Default = Off Mains Fail to Output - Default = Off Battery Low to Output - Default = Off

Keypad/Keyswitch Options-Partition A
This address allows modification of how Partition A arming, Stay and control keys work at the keypad. 110
ARM button before code to set - Default = Off STAY button required before code to turn on Stay Mode - Default = Off Disable ARM Button - Default = Off ARM button can disarm system during exit delay - Default = On STAY button can disarm Stay Mode at any time - Default = On No Exit Beeps to keypads in Stay Mode - Default = Off Key-switch Enabled - Default = Off Key-switch Mode - Default = Off
ARM button required before code to set - This option determines if the ARM button must be pressed before a code is entered to set Area A. If a keypad is assigned to both Partitions, this option should be set to allow individual arming of each area. This option disables the Arm button from disarming during the exit delay. STAY button required before code to set - This option determines if the STAY button must be pressed before a code is entered to set Area A Stay Mode. If a keypad is assigned to both Partitions, this option should be set to allow individual arming of Stay Mode for each area. If this option is set, the ARM button is disabled and the panel requires a code to arm as well as disarm. ARM button can disarm during exit delay - If this option is on then the arm button can disarm Partition A during the exit delay time with a single press of the button. If the option is off then the alarm can only be unset by a valid code, even during the exit delay time. STAY button can disarm Stay Mode - This option allows the Stay button to disarm Stay mode at any time (including when Stay Mode is fully set). If the option is off then Stay Mode can only be unset by a valid code. This feature is valid for keypad addresses 1 & 4 by default (4 being the default address for the Night Arm station). No Exit Beeps to keypads in Stay Mode - This option stops the exit beeps from occurring at all keypads when Stay Mode is set. Normally used for silent night arming. Enable Partition A Key-switch - If this option is turned on then the system tamper input (Tmp) becomes a Dual End of Line Input (Refer to Page 6 for wiring details). The low input 4K7 is reserved for Partition A key-switch operation. An open circuit will still be seen as a system tamper. Key-switch Mode - If this option is On then the key-switch has a toggle function (ie the arm/disarm state will follow the key-switch state). If Off then the key-switch is momentary (ie each single pulse will change the arm/disarm state). The panel tamper input is used to provide the key-switch function. Page 20

Page 21

Chirps & Flashes-Partition A
This block of addresses sets a number of output options which are specific and unique to the operation of partition or Area "A". Activity in Areas "B" will have no direct effect on the options set at these addresses. Addresses 111-118 In this block, address 111 relates to Output #1, 112 relates to Output #2 etc Addresses 111 (=Output-1)
Arm status to output - Default = Off Stay Mode on status to output - Default = Off Disarm status to output - Default = Off Remote Control Chirps (2) for Arm to output - Default = Off Remote Control Chirps (2) for Stay Mode On to output - Default = Off Remote Control Chirps (4) for Disarm to output - Default = Off Pulse on Arming to output - Default = Off Pulse on Disarming to output - Default = Off
Arm indication to output - This option will turn the output on when Area "A" is armed. The output will turn on at the start of the exit delay and turn off when the Area is disarmed. The output reset time should be set to zero. Stay Mode On indication to output - This option will turn the output on when Area "A" Stay Mode is armed. The output will turn on at the start of the exit delay and turn off when Stay Mode is disarmed. The output reset time should be set to zero. Disarm indication to output - This option will turn the output on when Area "A" is Disarmed. The output will turn on when the Area A is disarmed and turn off when the Area is Armed or in Stay Mode. The output reset time should be set to zero. Remote Control Chirps for Arm to output - This option will map two short pulses (Chirps) to the output when Area "A" is armed via a Remote Control, ( the length of the pulses is set by the pulse timer Address 221-228). Remote Control Chirps for Stay Mode On to output - This option will map two short pulses (Chirps) to the output when Area "A" Stay Mode is set via a Remote Control Button ,( the length of the pulses is set by the pulse timer Address 221-228). Remote Control Chirps for Disarm to output - This option will map four short pulses (Chirps) to the output when Area "A" is Disarmed via a R/C Button, ( the length of the pulses is set by the pulse timer Address 221-228). Pulse on Arming to output - This option will send a pulse to the Output each time Area"A" is armed ( the length of the pulses is set by the pulse timer Address 221-228). Pulse on Disarming to output - This option will map a pulse to the Output each time Area"A" is disarmed ( the length of the pulses is set by the pulse timer Address 221-228).
Note: 112 through 118 are as above but applied to outputs 2-8

Page 22

Chirps & Flashes-Partition B
This block of addresses sets a number of output options which are specific and unique to the operation of partition or Area "B". Activity in Areas "A" will have no direct effect on the options set at these addresses. Addresses 121-128 In this block, address 121 relates to Output #1, 122 relates to Output #2 etc Addresses 121 (=Output-1)

Page 24

Non-Latching 24 Hour Zone Zones 1-8. (Default = No zones) A Non-Latching 24 Hour Zone will operate as a normal 24 Hour zone except that when the zone re-seals the zone LED and any assigned outputs will reset automatically. Swinger Shutdown (1 Shot Siren Lockout) Zones Zones 1-8. (Default = No zones) A Lockout Zone will only cause the alarm output to sound once during and armed period. If the lockout function is not programmed then the zone can cause the audible alarms to sound on every zone alarm. In the case of a 24 hour zone, if this option is turned on then the zone will only activate the alarm output/s once and must be reset by a code before another alarm signal can operate the output/s again. Chime (Day) Zone when Disarmed Zones 1-8. (Default = No zones) A Chime Zone can be used as a door minder in a shop to warn when a customer has entered the premises. A Chime zone works when the alarm is disarmed, but becomes a normal security zone when armed. Chime zones can be temporarily disabled with the Control button if programmed to do so. Permanent Chime (Day) Zone Zones 1-8. (Default = No zones) A Permanent Day Zone can be used as a door minder in a shop to warn when a customer has entered the premises. A Permanent Chime zone will never cause an activation when the alarm is armed). Chime zones can be temporarily disabled with the Control button if programmed to do so. Force Arm Zones Zones 1-8. (Default = No zones) This option allows programming of which zones can be unsealed and still allow the panel to arm. Option 4 at Address 170 must be on before this address has any effect. This option allows setting (Arming) of the panel if low security areas are not sealed at the time of arming. Report Excluded Zones to Monitoring Station Zones 1-8. (Default = All zones) If this option is on then the zone will report any exclusion (Bypass) of the zone to a Staying Station via Contact ID or 4 + 2. Send Multiple Alarms to Monitoring Station Zones 1-8. (Default = All zones) If this option is assigned to the zone, the zone can send multiple activation reports to a Staying company during any armed cycle. If off, the zone can only send one activation per armed cycle. In the case of a 24 hour zone, if this option is turned off then the zone will only send one signal via the dialler and must be reset by a code before another signal can be sent. Report Zone Tampers to Monitoring Station Zones 1-8. (Default = All zones) This option allows the programming of zone tampers to be sent via the dialler to a Staying Station. Area B & Common Area Zones Report to Area B Account Zones 1-8. (Default=No zones) If a zone is in Area B only or is a zone in both Areas A&B (Common Area to areas A & B), this address allows the option of specifying which Contact-ID account number a zone alarm will report to. The default is t hat a zone in Area B or a zone in a Common Area zone will report to area A account code ( ddress 506) A but if this option is on for a zone in Area B or a zone in a common Area, it will report to the Area B account code (Address 507). Zone Inactivity Timer Zones 1-8. (Default = No Zones) This option allows the programming of which zones will be Stayed for inactivity. All zones programmed with this feature ON will be Stayed for activity for the period set below (Address 240). The inactivity timer only works during the disarmed state and is accumulative, which means that if a zone does not trip at least once during a disarm period the inactivity timer is not reset for that zone and will continue with the balance of the time period left when the panel is next disarmed. The timer for each zone is reset every time a zone unseals.

Zone Inactivity Timer

240 Inactivity Timer - 0-255 Hours. Default =120 Hours (=5 Days)

Entry Delays

Zone 1 Entry Delay Time - 0-9999 Seconds (Default = 20 Sec) Zone 2 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec) Zone 3 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec) Zone 4 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec) Zone 5 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec) Zone 6 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec) Zone 7 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec) Zone 8 Entry Delay Time - 0-9999 Seconds (Default = 0 Sec)

Exit Delays

Partition A Exit Delay Time - 0-255 Seconds (Default = 60 Sec) Partition B Exit Delay Time - 0-255 Seconds (Default = 60 Sec)

Pulse Count Timer

229 Pulse Count Timer - 0-255 Seconds (Default = 60 Sec)

Page 27

KEYPAD PROGRAMMING Keypad Partition
A keypad must be assigned to a Partition before it can control the Partition (ie to allow Arm/Disarm facilities). Keypads Assigned to Partition A - Option Keypad 1-8 (Default = All keypads 1-8) Keypads Assigned to Partition B - Option keypad 1-8 (Default = None)
Keypads with Panic Button enabled
The panic button on all keypads can be set for delayed or instant operation. If you do not want the Panic function enabled at any of the keypads you can disable the operation at this address. This option may be useful where a keypad has to be installed in a public area. 173 Keypads with the Panic Button Enabled - Option keypad 1-8 (Default = All keypads 1-8)
Keypads with Buttons 1&3 Panic enabled
An alternative Panic function to the dedicated panic button is to press the keypad buttons 1&3 simultaneously. If you do not want this Panic function enabled at any of the keypads you can disable the operation at this address. This option may be useful where a keypad has to be installed in a public area. 174 Keypads with the Panic Buttons 1&3 Enabled - Option keypad 1-8 (Default = All keypads 1-8)
Panic Alarm to Keypad Buzzer
The two panic functions at the keypads (Address 173 or 174) can be audible or silent at the keypads. If a silent panic is required the option must be turned off at this address. For an audible Panic Beep at the keypad/s turn this option on. 175 Panic Alarm to Keypad Buzzer - Option keypad 1-8 (Default = All keypads 1-8)

To teach a Crow FREEWAVE-PIR into a zone, Remove the front cover off the PIR and while the detector is in your hand, Press & Hold the Tamper Switch with your finger. Now, press the appropriate address number to teach the wireless code into a zone followed by the Enter key (eg: P604E for wireless Zone 4). This will start the keypad beeps to indicate Learn mode. As soon as you hear the keypad beeps, release the Tamper Switch of the FreeWave-PIR. This will initiate a Tamper Transmission which will be received & learnt by the PW-8 and the keypad will give 3 short beeps indicating it has learnt the code. The keypad will then exit learn mode. To teach a Crow FREEWAVE-360 Degree Ceiling PIR into a zone, Remove the small lens locking screw at front of detector and slowly twist off (clockwise) the lens. With the lens off the PIR and while the detector is in your hand, Press & Hold the Tamper Switch with your finger. Now, press the appropriate address number to teach the wireless code into a zone followed by the Enter key (eg: P602E for wireless Zone 2). This will start the keypad beeps to indicate Learn mode. As soon as you hear the keypad beeps, release the Tamper Switch of the FreeWave 360 degree Ceiling PIR. This will initiate a Tamper Activation Transmission which will be received & learnt by the PW-8 and the keypad will give 3 short beeps indicating it has learnt the code. The keypad will then exit learn mode. To teach a Crow FREEWAVE-Reed Switch into a zone, Remove the front cover of the Reed Switch and while the Reed
Switch is in your hand, Press & Hold the Tamper Switch with your finger. Now, press the appropriate address number to teach the wireless code into a zone followed by the Enter key (eg: P605E for wireless Zone 5). This will start the keypad beeps to indicate Learn mode. As soon as you hear the keypad beeps, release the Tamper Switch of the FreeWave-Reed Switch. This will initiate a Tamper Transmission which will be received & learnt by the PW-8 and the keypad will give 3 short beeps indicating it has learnt the code. The keypad will then exit learn mode.
To teach a Crow FREEWAVE-SMOKE detector into a zone, first press the appropriate address number to teach the wireless
code into a zone (eg: P606 for wireless Zone 6) but DONT press the Enter key yet. Now, while the Smoke Detector is in your hand, press and hold the Test Button of the Smoke Detector until you hear the smoke detectors beeper which will be approx. 20 seconds after you press the Smoke Detectors Test button. The Enter button on the keypad Must be pressed as soon as the smoke detector beeper is heard.
Wireless Detector Zone Options

231 Zone 1 Options

Visonic Wireless PIR- If a Visonic K900 radio PIR is used PowerWave Wireless Receiver, setting this bit allows the panel to correctly recognize the alarm, tamper & battery low signal from the device. Visonic Powercode (unsupervised) - If a Visonic Powercode Wireless device is used on the PowerWave Wireless Receiver, setting this bit allows the panel to correctly recognize the alarm and battery low signal from the device but the supervised signal is ignored.
33 Visonic Powercode (supervised) - If the Visonic Powercode range of Wireless PIR or reed switch are used on the PowerWave Wireless Receiver, setting this bit allows the panel to correctly recognize the alarm, tamper & battery low signal from the device. Setting this option on also starts a 4 hour timer for the supervised signal. The 4 hour timer is constantly being reset while valid supervised signals are being received every 1-1.5 hours. If no supervised signals are received from the PIR within the 4 hour period, a supervised alarm is generated.
Note: Addresses 232 through 238 are as above but applied to zones 2-8

Page 31

Wireless Zone Supervision Timer
239 WIRELESS ZONE SUPERVISED TIMER - Default = 240 Minutes = 4Hours (Value 0-255 Minutes)
Remote Control Button Learning
To learn a Remote Control Button into the panel, press the appropriate address number (e.g. 614 for Button 4). The keypad buzzer will beep once a second to indicate learn mode has been initiated and the Led on the RX-40 Receiver board will flash. The Remote Button you wish to learn must transmit a signal within 30 seconds of entering learn mode otherwise the panel will time out and nothing will be loaded. If a valid code is received within the 30 seconds the keypad will give 3 short beeps and exit learn mode. To remove a loaded Remote Button at a single address only, enter in the learning address as above e.g. 614, then without operating the transmitter and before the 30 second timer expires press the Enter button. This will remove the Button loaded against this address. Learn Button # 1 Learn Button # 2 Learn Button # 3 Learn Button # 4 Learn Button # 5 Learn Button # 6 Learn Button # 7 Learn Button # 8
Remote Control Arm/Disarm Options
Addresses 151-158 In this block, address 151 relates to Wireless User Button #1, 152 relates to Wireless User Button #2 etc., where Addresses (151 - 158) are used to select the operational settings for each of the 8 Remote Control Buttons. Functions such as arm only, disarm only or both can be selected for each button independently. 151-Button #1 Options (Default = 1.3.4)
Assigned to Partition A - Default = On Assigned to Partition B - Default = Off Can Arm - Default = On Can Disarm - Default = On Can turn Stay Mode On - Default = Off Can turn Stay Mode Off - Default = Off Spare - Default = Off Disabled if panel is in alarm - Default = Off
Option Option Option Option Option

Listen-in Options - Output 1
The panel provides the facilities to use a horn speaker connected to Output 1 to listen to the call being made by the dialler. To use this feature a horn speaker MUST be connected to Output 1 and the output set for siren Mode (Address 31 Option 5). 190

Auto-Answer Ring Count

The auto-answer ring count is the number of rings the panel must count before answering an in-coming call. For Fax defeat to work the auto-answer ring count must be set to a number other than 0. (typically 25 rings) 249 Auto-answer Ring Count - Value 0-99 (0= Auto-answer disabled) - (Default = 17)
Mains Fail Reporting Delay
This address (319) is used to set a timer that delays the reporting of Mains Failure to a Central Station. If the mains voltage returns before the timer expires then no report is sent. 319 Mains Failure Report Delay - Value 0-9999 Seconds - (Default = 1800 sec = 30 minutes)

Test Report Time

This option sets the days of the week and the time when an automatic test report is sent to a Central Station. 402 Automatic Test Report Hour/Minute - Value 0-2359 - (Default = 0330 = 3:30am) 404 Automatic Test Report Day/s of Week - Value 1-7 (where 1 = Sunday, 2 = Monday, etc) - (Default = 7 = Saturday)

Telephone Numbers

The panel can be programmed with up 4 telephone numbers. The numbers can be up 16 digits long. Dialling modifiers such as Pauses or Hexadecimal digits can be programmed into the number sequence as per the chart above: Telephone # 1 - Value = 1-16 digits Telephone # 2 - Value = 1-16 digits Telephone # 3 - Value = 1-16 digits Telephone # 4 - Value = 1-16 digits

Page 39

Dialling Protocol
Addresses 241-244 In this block, address 241 relates to Phone #1, 242 relates to Phone #2, etc. This block of addresses (241 - 244) are used to set the reporting format which will be sent when an alarm occurs for each of the telephone numbers. 241-Telephone #1 Options (Default = 1)
Contact ID Domestic Dial Pager Speech Dialler
Contact ID - If this option is set for the telephone number, the panel will send a Contact ID message to a Central Station. Domestic Dial - If this option is set for the telephone number, the panel is expecting to dial a residential telephone number when an alarm occurs. The message sent consists of a siren tone over the phone to alert the person called that an alarm is in progress. The alarm can be cancelled by the person called by pressing any button on a touch tone phone during the quiet period. If the alarm is cancelled by a valid user code the dialler will stop any further calls Pager - Report alarm events using Arrowhead "Pager" format. This format utilises Telstras pager network to post numeric messages to a compatible pager. (NOTE: The client account number should not start with a 0) Speech Dialer - If the optional speech board is fitted to the panel, then selecting this option for the telephone number will allow voice messages that you record, to be sent via the telephone following an alarm.

= Stop Dialling if Kissed off Page 38 = Monitor Call Progress Page 38 = Blind Dial Page 38 = Use Group Numbers for Contact ID Page 38 = Send Restores = Send Test Calls = Ignore Domestic Kiss-Off = Spare
Dialler Programming Options
185 Dialler options (Default = 2,3,6,7) Page 33 = Dialler ON = Fax Defeat (Double Call) = Disable Telephone Line Monitoring = DTMF (Tone) or Pulse Dialing - Default = Off (NOTE: Options 4 & 5 must be OFF for DTMF Dial) = DTMF or Reverse Pulse Dialing - Default = Off (NOTE: Options 4 & 5 must be OFF for DTMF Dial) = Short (70ms) DTMF or Long (100ms) DTMF Dialling Tones (for Australia) - Default = On = Auto Detect Modem Mode = Bell 103 or V21
186 Dialler Options 1 (Default = 1-5,7,8) = Report Duress Alarm = Report Mains Fail = Report Battery low = Report Wireless Detector Battery Low = Report System Tamper = Report Line Fail = Report Supervised Wireless Alarm = Report Zone Inactivity Alarm Page 34
187 Dialler Options 2 (Default = 1,2,3) = Report Manual Panic Alarm = Report Manual Fire Alarm = Report Manual Medical Alarm Page 34
188 Dialler Options 3 (Default = 3,4,6,7) Page 35 = Report Open/Close = Report Stay Mode Open Close = Report Open after Alarm = Report Stay Mode Open after Alarm = Report 24 Hour Alarms when set to Domestic /voice mode = Send Open immediate or after exit delay = Report Zone alarms in Stay Mode = Spare

Keypad Listen-in Options

189 Keypad Listen-in Options (Default = None) Page 37 = Enabled During Dialling in Disarm State only = Enabled During Dialling in Armed State only = Enabled During Dialling in Stay Mode State only = Enabled Throughout the call in Disarm State only = Enabled Throughout the call in Armed State only = Enabled Throughout the call in Stay Mode State only = Listen-in Enabled when the panel answers a call = Enabled at All Times

Page 48

Output # 1 Listen-in Options
190 Output # 1 Listen-in Options (Default = None) Page 38 = Enabled During Dialling in Disarm State only = Enabled During Dialling in Armed State only = Enabled During Dialling in Stay Mode State only = Enabled Throughout the call in Disarm State only = Enabled Throughout the call in Armed State only = Enabled Throughout the call in Stay Mode State only = Listen-in Enabled when the panel answers a call = Enabled at All Times

Output Delay ON time

Output 1 Delay ON Time Output 2 Delay ON Time Output 3 Delay ON Time Output 4 Delay ON Time Output 5 Delay ON Time Output 6 Delay ON Time Output 7 Delay ON Time Output 8 Delay ON Time Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Value 0-255 Seconds (Default = 0 Sec) Page 18 Page 18 Page 18 Page 18 Page 18 Page 18 Page 18 Page 18

505 Upload/Download Site Code Number - 8 Characters (Default = None) Page 33

Page 51

Contact ID Account Numbers
Contact ID Partition A Account Code Number - 4 Digits (Default = 0000) Contact ID Partition B Account Code Number - 4 Digits (Default = 0000) Page 36 Page 36
Wireless Detector Learning
Learn Mode for Zone Learn Mode for Zone Learn Mode for Zone Learn Mode for Zone Learn Mode for Zone Learn Mode for Zone Learn Mode for Zone Learn Mode for Zone #1 #2 #3 #4 #5 #6 #7 #8 Page 29 Page 29 Page 29 Page 29 Page 29 Page 29 Page 29 Page 29
620 Learn Mode for Button # 1 Learn Mode for Button # 2 Learn Mode for Button # 3 Learn Mode for Button # 4 Learn Mode for Button # 5 Learn Mode for Button # 6 Learn Mode for Button # 7 Learn Mode for Button # 8 Page 31 Page 31 Page 31 Page 31 Page 31 Page 31 Page 31 Page 31
Restore All Factory Defaults Page 41
625 Default User Codes Default Addresses 20-199 Default Addresses 200-399 Default Addresses 500-599 Default Wireless Detectors & Remote Controls Page 41 Page 41 Page 41 Page 41 Page 41
Clear Alarm Memory Buffer
626 Clear Alarm Memory Buffer Page 41
627 Walk Test Mode Page 41

Write to EEPROM Board

628 Write to EEPROM Board - (Write/Read Jumper on the EEPROM Must be On) Page 41

Read from EEPROM Board

629 Read from EEPROM Board - (Write/Read Jumper on the EEPROM Must be Off) Page 41

Page 52

Product Warranty
CROW (AUSTRALIA) P/L WARRANTY (Crow) warrants this product to be free from defects in materials and workmanship under normal use and service for a period of one year from the last day of the week and year whose numbers are printed on the printed circuit board inside his product. Crows obligation is limited to repairing or replacing this product, at its option, free of charge for materials or labor, if it is proved to be defective in materials or workmanship under normal use and service. Crow shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other then Crow. There are no warranties, expressed or implied, of merchantability or fitness for a particular purpose or otherwise, which extend beyond the description on the face hereof. In no case shall Crow be liable to anyone for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever, even if the loss or damage is caused by Crows own negligence or fault. Crow does not represent that this product can not be compromised or circumvented; that this product will prevent any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that this product will in all cases provide adequate warning or protection. Purchaser understands that a properly installed and maintained product can only reduce the risk of burglary, robbery or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss or damage as a result. Consequently, Crow shall have no liability for any personal injury, property damage or any other loss based on claim that this product failed to give any warning. However, if Crow is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause or origin, Crows maximum liability