MXB-2125

MXB-2200

MXB-2250

MXB-4 x 60 / x 80 / x x 320 20Hz - 30kHz > 150 >90dB >70dB 0.10 % 0.2 - 4 Volt 47 kOhm

MXB-4100

MXB-4125

MXB-4175

4 x 60 / 100

4 x 85 / 125

4 x 110 / 175

4 x 80 / 200

4 x 125 / 250

4 x 175 / 350

2 x 160

2 x 250

2 x 350

2 x 400

2 x 500

2 x 700

20Hz - 30kHz

> 150

>90dB

Technische Daten

Kanaltrennung Klirrfaktor (THD) Eingangsempfindlichkeit Eingangsimpedanz Frequenzweichen - Schalter fr 1 & 2 Kanal Tiefpass/Vollberich/Hochpass Variable Hochpassweiche Variable Tiefpassweiche BassBoost bei 45Hz Frequenzweichen - Schalter fr 3 & 4 Kanal Tiefpass/Vollberich/Hochpass Variable Hochpassweiche Variable Tiefpassweiche BassBoost bei 45Hz Cinch-Ausgnge Hochpegel-Eingnge (HighLevel-Input) Gertesicherung Abmessungen in mm Breite x Hhe Lnge 251 x Vollbereich

5 Pin Stecker

>70dB

0.10 %

0.2 - 4 Volt

47 kOhm

TP/Voll/HP 60Hz - 1.2kHz 40Hz - 150Hz

TP/Voll/HP

60Hz - 1.2kHz

40Hz - 150Hz

0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB

Vollbereich

0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB Vollbereich

5 Pin Stecker x2

Vollbereich 2x 7,5 Ampere 2x 15 Ampere 262 x 2x 20 Ampere 262 x 2x 25 Ampere 262 x 2x 20 Ampere 262 x 52 285

2x 20 Ampere

2x 25 Ampere

2x 35 Ampere

262 x 52
* technische nderungen vorbehalten
Congratulations on your purchase of a CRUNCH BLACKMAXX Amplifier. These quality audio products are designed and engineered to afford you years of uncompromised musical service. CRUNCH has utilized the latest electronic technologies in order to deliver a superb listening experience.

Contents

General Installation Notes, Installation of the amplifier, Electrical Connection.. Channel Amplifier - Features.... Channel Amplifier - Features.... Channel Amplifier - Applications, One 2 Channel Amplifier in Stereo Mode.... Channel Amplifier - Applications, One 2 Channel Amplifier in Mono/Subwoofer Mode... Channel Amplifier - Applications, One 4 Channel Amplifier with Front-/Rear Speakers... Channel Amplifier - Applications, One 4 Channel Amplifier in Mono/Subwoofer Mode with two Subwoofers.. Channel Amplifier - Applications, One 4 Channel Amplifier in 3 Channel Mode with Stereo Front Speakers and Mono Subwoofer... Channel Amplifier - Applications, One 4 Channel Amplifier in Stereo Mode (Front-/Rear Speakers) with One 2 Channel Amplifier in Mono/Subwoofer Mode... 25 Specifications..... 27
General Installation Notes
The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the mounting location you should minimize the length of the power and speaker leads. Minimizing both leads will yield a more reliable installation. It is also important to ensure that the heat sink fins are not against a panel or a surface, preventing air circulation. Do not install the amplifier on a subwoofer box or on vibrating parts of the vehicle, since the vibrations can cause damage to the amplifiers electrical components.
Installation of the amplifier
Mark the location for the mounting screw holes by using the amplifier as a template. Drill holes at the marked locations and firmly fasten the amplifier in place with the mounting screws supplied in the accessory kit. Before drilling or cutting any holes, investigate the layout of your automobile thoroughly: Take care when working near the gas lines or hydraulic lines and electrical wiring.

Electrical Connection

Ground (GND) This wire is the electrical ground and must be fastened securely to the vehicle chassis. The best method is to use a threading sheet metal screw since the threads cut into bare metal. Ensure that all paint or other insulation is remove from around the hole area, and using self tapping screw, securely affix the bare wire ends to the vehicle chassis. Use as short a piece of cable as possible - use the same gauge as was used for the +12V cable. Make sure that the connection is safe, a loose connection may result in amplifier noise and fault condition. Remote (REM) Many radios or other music sources have an output terminal for connection of the remote turn-on of the power amplifier. If a radio doesn't have a remote turn-on feature, then you can use the antenna relay wire, which activates the antenna motor. Please note, if the power antenna retracts when the radio is operating, then you cannot use the antenna relay wire to operate the remote turn-on. Batterie Connection (+12V) This wire is usually connected directly to the positive battery terminal. Ensure that the + power supply wire is fused via an assigned fuse in line with the + power supply wire. Please use a sufficient gauge for the installed amplifiers (min. 10-16 mm for MXB-280/MXB2125/MXB-2200/MXB-480 or min 16-25 mm for MXB-2250/MXB-4125/MXB-4175).This connection must be completed using spade lug with insulating sleeve. Fuses The integrated amplifier fuses protect the units from short circuit and overload. The fuse rating is for 4 Ohm loads (impedance) of the speakers, for 2 Ohm loads the fuses may have to get increased by up to 50% in case of higher power consumption.

BATTERY

CHASSIS GROUND

REMOTE

2 Channel Amplifier - Features MXB-280/MXB-2125/MXB-2200/MXB-2250

FILTER - SWITCH

This switch will route the output of the full range (FLAT), or a low pass (LOW PASS), or the output of the high pass (HIGH PASS) filter to the internal power amplifier

HIGH-/LOWPASS - ADJUST

HIGH PASS - The built in high pass filter is fully variable from 60Hz to 1200Hz (1.2KHz), with a rolloff of 12dB/octave LOW PASS - The built in low pass filter is fully variable from 40Hz to 150Hz, with a rolloff of 12dB/octave
This allows you to match the amplifier input sensitivity to the output level of the source (head unit)

BASS BOOST

Allows you to adjust the bass boost from 0dB up to 12dB

POWER - LED

It indicates amplifier has turn on signal

PROTECT - LED

It indicates the fault operation of the amplifier. When the fault conditions (overload, excessive heat or short circuit of speaker) arise, the protection curcuit is engaged to protect both the speakers and the amplifier against damage.

HI INPUT

Accepts speaker level inputs from head units that do not have line level (RCA) outputs
LINE LEVEL - INPUT OUTPUT
Provides a full range line level (RCA) output that allows the use of additional amplifiers Accepts line level (RCA) inputs from 0.2 to 4 Volts
4 Channel Amplifier - Features MXB-480/MXB-4100/MXB-4125/MXB-4175
HIGH PASS - The built in high pass filter is fully variable from 60Hz to 1200Hz (1.2KHz), with a rolloff of 12dB/octave
LOW PASS - The built in low pass filter is fully variable from 40Hz to 150Hz, with a rolloff of 12dB/octave Accepts line level (RCA) inputs from 0.2 to 4 Volts

INPUT SELECT

Allows you to chose 2 or 4 channel operations

BASS BOOST POWER - LED

It indicates amplifier has turn on signal Allows you to adjust the bass boost from 0dB up to 12dB

OUTPUT

Provides a full range line level (RCA) output that allows the use of additional amplifiers
2 Channel Amplifier - Applications MXB-280/MXB-2125/MXB-2200/MXB-2250
One 2 Channel Amplifier in Stereo Mode
Interconnect cable checklist:
Connect the LINE LEVEL INPUT of the amplifier to the head unit line output with good quality RCA to RCA cables. Connect the speakers with the terminal block (SPEAKERS/ + L - and + R -) of the amplifier. The minimum final speaker impedance must not be below 2 Ohm per channel. Too low speaker loads result in too high heat dissipation and may cause the amplifier run into protection. Please observe speaker channel and polarity as printed by the speaker terminal block. Incorrect phasing of the speakers results in total loss of bass response.
Caution Be careful not to connect speaker (-) to the ground or vehicle chassis. FILTER SELECT
If larger than 20 cm speakers are used, the FLAT position is recommended. For all smaller speakers (8.7cm - 16cm) the Highpass-Position (HIGH PASS) is recommended, which eliminates the lowest frequencies and protects the speakers from damage. Set the crossover-frequency between 60Hz - 150Hz, depending of the size of the installed speakers. The Highpass adjustment can be done with the HIGH PASS control. In this configuration example the LOW PASS control is not used.
Turn the INPUT LEVEL control on the amplifier to 4V position. Turn the head unit volume control to about 80-90% of its full setting. Turn the INPUT LEVEL control clockwise until you hear some distortion. Then turn back the INPUT LEVEL control slightly until you can hear clean sound.

Turn the BASS BOOST control into 0dB - position.
Speakers (Right) 2 - 8 Ohms
Gray: Left Speaker + Brown: Left Speaker Black: Ground White: Right Speaker + Green: Right Speaker R L
Connect RCA cable from head-unit with RCA input (LINE LEVEL INPUT).
Speakers (Left) 2 - 8 Ohms
One 2 Channel Amplifier in Mono/Subwoofer Mode
Connect the LINE LEVEL INPUT of the amplifier to the head unit line output with good quality RCA to RCA cables. Connect the speakers with the terminal block (SPEAKERS/ + BRIDGED -) of the amplifier. The minimum final speaker impedance must not be below 2 Ohm per channel. Too low speaker loads result in too high heat dissipation and may cause the amplifier run into protection. Please observe speaker channel and polarity as printed by the speaker terminal block. Incorrect phasing of the speakers results in total loss of bass response.
In 1 Channel/Mono-Mode select the Lowpass-Position (LOW PASS), which eliminates the higher frequencies. The recommended crossover frequency ranges between 60 - 100Hz, depending on the size and response of the Subwoofer. The Lowpass adjustment can be done with the LOW PASS control. In this configuration example the HIGH PASS control is not used.
The BASS BOOST - Control increases the bass level at 45 Hz max. +12dB. Caution! Please use the Bass-Boost carefully. The additional boost may result in clipping or overload.

Subwoofer 4 - 8 Ohms

4 Channel Amplifier - Applications MXB-480/MXB-4100/MXB-4125/MXB-4175
One 4 Channel Amplifier with Front-/Rear Speakers
Connect the head unit line outputs with good quality RCA to RCA cables to the INPUT CH1&2 / CH3&4 of the amplifier. Connect the Front-/Rear Speakers with the terminal blocks (SPEAKERS / + CH1 -, + CH2 -, + CH3 -, and + CH4 -) of the amplifier. The minimum final speaker impedance must not be below 2 Ohm per channel. Too low speaker loads result in too high heat dissipation and may cause the amplifier run into protection. Please observe speaker channel and polarity as printed by the speaker terminal block. Incorrect phasing of the speakers results in total loss of bass response.
Caution Be careful not to connect speaker (-) to the ground or vehicle chassis. FILTER SELECT (CH1/2 & CH3/4)
INPUT LEVEL (CH1/2 & CH3/4)
Turn the INPUT LEVEL controls on the amplifier to 4V position. Turn the head unit volume control to about 80-90% of its full setting. Turn the INPUT LEVEL controls clockwise until you hear some distortion. Then turn back the INPUT LEVEL controls slightly until you can hear clean sound.
BASS BOOST (CH1/2 & CH3/4)

The INPUT SELECT - switch must be in 4 - position.
Gray: Left Speaker + Brown: Left Speaker Black: Ground White: Right Speaker + Green: Right Speaker -

Rear-Speakers 2 - 8 Ohms

Connect RCA outputs from head-unit with RCA inputs (INPUT CH1/2 and CH3/4).
Front-Speakers 2 - 8 Ohms
One 4 Channel Amplifier in Mono/Subwoofer Mode with two Subwoofers
Connect the head unit line outputs with good quality RCA to RCA cables to the INPUT CH1&2 of the amplifier. Connect the Subwoofers with the terminal blocks (SPEAKERS / + BRIDGED - from Channel 1&2 and + BRIDGED - from Channel 3&4) of the amplifier. The minimum final speaker impedance must not be below 4 Ohm per channel pair. Too low speaker loads result in too high heat dissipation and may cause the amplifier run into protection. Please observe speaker channel and polarity as printed by the speaker terminal block. Incorrect phasing of the speakers results in total loss of bass response.
In Mono/Subwoofer-Mode select the Lowpass-Position (LOW PASS), which eliminates the higher frequencies. The recommended crossover frequency ranges between 60 - 100Hz, depending on the size and response of the Subwoofers. The Lowpass adjustment can be done with the LOW PASS control. In this configuration example the HIGH PASS control is not used.
The INPUT SELECT - switch must be in 2 - position.
Connect RCA outputs from head-unit with RCA inputs (INPUT CH1/2).

Subwoofer 4 - 8 Ohm Ohms

One 4 Channel Amplifier in 3 Channel Mode with Stereo Front Speakers and Mono/Subwoofer
Connect the head unit line outputs with good quality RCA to RCA cables to the INPUT CH1&2 / CH3&4 of the amplifier. Connect the Front Speakers with the terminal block (SPEAKERS / + CH1 - and + CH2 ) of the amplifier. Connect the Subwoofer with the terminal block (SPEAKERS / + BRIDGED - from Channel 3&4) of the amplifier. The minimum final speaker impedance must not be below 2 Ohms Stereo and 4 Ohms Mono. Too low speaker loads result in too high heat dissipation and may cause the amplifier run into protection. Please observe speaker channel and polarity as printed by the speaker terminal block. Incorrect phasing of the speakers results in total loss of bass response.
Caution Be careful not to connect speaker (-) to the ground or vehicle chassis.
FILTER SELECT (Front Speakers Channel 1&2)
X-OVER SELECT (Subwoofer Channel 3&4)
In Mono/Subwoofer-Mode select the Lowpass-Position (LOW PASS), which eliminates the higher frequencies. The recommended crossover frequency ranges between 60 - 100Hz, depending on the size and response of the Subwoofer. The Lowpass adjustment can be done with the LOW PASS control. In this configuration example the HIGH PASS control is not used.

Turn the BASS BOOST control from the Front Speakers (Channel 1&2) into 0dB - position. The BASS BOOST - Control from the Subwoofer (Channel 3&4) increases the bass level at 45 Hz max. +12dB. Caution! Please use the Bass-Boost carefully. The additional boost may result in clipping or overload.
One 4 Channel Amplifier in Stereo Mode (Front-/Rear- Speakers) with One 2 Channel Amplifier in Mono/Subwoofer Mode (Bass Amplifier)
Connect the INPUT of the 4 Channel Amplifier to the head unit line outputs with good quality RCA to RCA cables. Connect the OUTPUT of the 4 Channel Amplifier with the LINE LEVEL INPUT of the designated Bass Amplifier (2 Channel Amplifier) with a further RCA cable. Connect the Front-/Rear Speakers with the terminal blocks (SPEAKERS / + CH1 -, + CH2 -, + CH3 - and + CH4 -) of the 4 Channel Amplifier. Connect the Subwoofer with the terminal block (SPEAKERS / + BRIDGED -) of the designated Bass Amplifier (2 Channel Amplifier). The minimum final speaker impedance must not be below 2 Ohms for the 4 Channel Amplifier, the total impedance of the Subwoofer(s) must not be below 4 Ohms. Too low speaker loads result in too high heat dissipation and may cause the amplifier run into protection. If you use more than one speaker (Subwoofer), make sure that both are connected in phase. Incorrect polarity of the speakers results in total loss of bass response.
Caution Be careful not to connect speaker (-) to the ground or vehicle chassis. Control settings of the 4 Channel Amplifier: FILTER SELECT (CH1/2 & CH3/4)
Control settings of the Bass Amplifier (2 Channel Amplifier): FILTER SELECT
INPUT LEVEL see descriptions for 4 Channel Amplifier above BASS BOOST

Bass Amplifier

Connect OUTPUT of 4 Channel Amplifier with LINE LEVEL INPUT of Bass Amplifier.

4 Channel Amplifier

Rear Speakers 2 - 8 Ohms
MXB-280 Channels Output Power Ratings at 14.4 Volts Watts at 4 Ohm load - RMS / MAX. W Watts at 2 Ohm load - RMS / MAX. Output Power Ratings at 14.4 Volts bridged W Watts at 4 Ohm load - RMS Watts at 4 Ohm load - Max. Frequency response -3dB Damping factor Signal to noise ratio Channel seperation >70dB 0.10 % 0.2 - 4 Volts 47 kOhms >70dB 0.10 % 0.2 - 4 Volts 47 kOhms >90dB >90dB > 150 > 150 20Hz - 30kHz 20Hz - 30kHz 1 x x x 800 20Hz - 30kHz > 150 >90dB >70dB 0.10 % 0.2 - 4 Volts 47 kOhms 1 x x x x x 1000 20Hz - 30kHz > 150 >90dB >70dB 0.10 % 0.2 - 4 Volts 47 kOhms 2 x 80 / x 125 / x 200 / x 60 / x 75 / x 125 / x 150 / 250 2x 250 / 2

MXB-4 x 60 / x 80 / x x 320 20Hz - 30kHz > 150 >90dB >70dB 0.10 % 0.2 - 4 Volts 47 kOhms

Specifications

THD & N Input Gain Control Input Impedance Crossover Channel 1 & 2 Full/Lowpass/Highpass Variable Highpass Crossover 12 dB Variable Lowpass Crossover 12 dB BassBoost Control at 45Hz Crossover Channel 3 & 4 Full/Lowpass/Highpass Variable Highpass Crossover 12 dB Variable Lowpass Crossover 12 dB BassBoost Control at 45Hz RCA Line Outputs High Level Inputs Fuses Heatsink size in mm Width x Height Lenght 251 x Fullrange

5 Pin Plug

0.2 - 4 Volts

47 kOhms

Full/LP/HP 60Hz - 1.2kHz 40Hz - 150Hz

Full/LP/HP

Fullrange
0dB bis +12dB 0dB bis +12dB 0dB bis +12dB 0dB bis +12dB Fullrange

5 Pin Plug x2

Fullrange 2x 7,5 Ampere 2x 15 Ampere 262 x 2x 20 Ampere 262 x 2x 25 Ampere 262 x 2x 20 Ampere 262 x 52 285
* All specifications subject to change without notice

REV 1.0

CJENIK MALOPRODAJA HRVATSKA SIJEANJ 2008 Proizvod Opis Slika Barkod/Dimenzije Opcija Proizvoda

MPC KN

Pojaala
2-Channel Amplifier BlackMaxx Serie 806576180514 *301 251x55x185 mm 2-Channel Amplifier BlackMaxx Serie 806576212515 *302 251x55x227 mm 2-Channel Amplifier BlackMaxx Serie 806576220510 *303 251x55x285 mm 2-Channel Amplifier BlackMaxx Serie 806576225515 *304 251x55x310 mm p 4-Channel Amplifier BlackMaxx Serie 806576412519 *306 251x55x310 mm 4-Channel Amplifier BlackMaxx Serie 806576417514 *307 251x55x400 mm 5-Channel Amplifier BlackMaxx Serie 806576055211 *308 260x57x420 mm CRUNCH AMP BLACK MAXX MXB-x 80 / 160 Watt at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 40-150 Hz Bass-EQ, Tweeter-EQ, Line Outputs AKCIJA -10%!!! CRUNCH AMP BLACK MAXX MXB-x 125 / 250 Watt at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 40-150 Hz Bass-EQ, Tweeter-EQ, Line Outputs AKCIJA -10%!!! CRUNCH AMP BLACK MAXX MXB-x 200 / 400 Watt at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 40-150 Hz Bass-EQ, Tweeter-EQ, Line Outputs AKCIJA -10%!!! CRUNCH AMP BLACK MAXX MXB-x 250 / 500 Watts at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 40-150 Hz Bass-EQ, Tweeter-EQ, Line Outputs AKCIJA -10%!!! CRUNCH AMP BLACK MAXX MXB-x 125 / 250 Watt at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 40-150 Hz Bass-EQ, Tweeter-EQ, Line Outputs AKCIJA -10%!!! CRUNCH AMP BLACK MAXX MXB-x 175 / 350 Watts at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 40-150 Hz Bass-EQ, Tweeter-EQ, Line Outputs AKCIJA -10%!!! CRUNCH AMP BLACK MAXX BLX-x 100 + 1 x 300 Watt at 4 Ohms Highpass 80-1200 Hz & Lowpass 40-150 Hz. CH 5: Lowpass 40-400 Hz, Variable Bass-Boost AKCIJA -10%!!! CRUNCH MONO BLOCK BLACK MAXX BLX-2000D 1 x 600 / 1000 / 1500 Watts RMS at 4 / 2 / 1 Ohms 1 x 2000 Watts max. Power Subsonicfilter 20-50 Hz, Lowpass 50-250 Hz Full-Range Line Outputs, Bass-Remote AKCIJA -10%!!!

1099,99

1499,99

1899,99

2279,99

2649,99

3259,99
Mono-Block BlackMaxx Serie 806576200017 *309 260x57x380 mm

4549,99

Zvunici
Coaxial System 10cm *1103 BlackMaxx Serie CRUNCH 2-WEG KOAX BLACK MAXX BMX42CX Power 50/100 Watts, Impedance 4 Ohms 13 mm Neodym-Tweeter, Chromed Cone, Rubber Surround, Chromed Pole Plates, Installation Depth 55 mm, Inst. Diameter 98 mm

449,99

Herman Josip d.o.o., Tel. +628 229, Fax +628 230, e-mail: josip.herman@ck.htnet.hr, Internet stranica: www.hermanjosip.com Strana 1 od 6
CJENIK MALOPRODAJA HRVATSKA SIJEANJ 2008 Proizvod Opis Slika Barkod/Dimenzije Opcija Proizvoda Coaxial System 13cm *1104 BlackMaxx Serie 806576211457 CRUNCH 2-WEG KOAX BLACK MAXX BMX52CX Power 75/150 Watts, Impedance 4 Ohms 13 mm Neodym-Tweeter, Chromed Cone, Rubber Surround, Chromed Pole Plates, Installation Depth 62 mm, Inst. Diameter 115 mm

525,00

PREIS-TIPP / Test in autohifi 02/2007 - Oberklasse 56 Punkte Fazit des Testers: Das Crunch-Kompo ist jeden Euro wert!

NOVO 2008

Kompo-System 16 cm BlackMaxx-Serie Tube 20 cm Passiv BlackMaxx Serie x 31 cm Tube 20 cm Aktiv BlackMaxx Serie x 31 cm CRUNCH BLACK MAXX 2-Wege System MXB-6.2C Snaga 125/250 Watt, Impedanz 4 Ohm 25 mm Gewebe-Kalotte, Gummisicke, 12 dB Weiche mit berlastschutz Einbautiefe 69 mm, Einbauffnung 144 mm CRUNCH GROUND POUNDER BMGPP8 Tube Passiv 8" (20 cm) BassTube, 4 Ohm Impedance High Power Woofer with 37 mm Voice Coil 150/300 Watts, with VU-Meter, black CRUNCH GROUND POUNDER BMGPAAktive Bass Tube, Tube Aktiv 8" (20 cm) Aktive-Bass Tube Power 150 Watts adjustable Gain, 80/120 Hz LP, VU-Meter High/Low-Inputs, Phase Switch, black CRUNCH WOOFER BLACKMAXX CMX12 Power 250/400 Watts, Impedance 2 x 4 Ohms 50 mm / 2,0" Voice Coil, Steel Basket Fs 34 Hz, Qts 0,55, VAS 67 L, 89 dB Inst. Depth 130 mm, Inst. Diameter 280 mm CRUNCH SINGLE BANDPASS SMAXX-12 Power 400 Watts, Impedance 4 Ohms Single Bandpass Box with BMX-12 Subwoofer New white LEDIllumination Chrome-Cone, 2,5" (64 mm) Voice Coil CRUNCH DUAL BANDPASS DMAXX-12 Power 800 Watts, Impedance 4+4 Ohms Dual Bandpass Box with BMX-12 Subwoofer New white LED-Illumination Chrome-Cone, 2,5" (64 mm) Voice Coil CRUNCH Tube-Subwoofer TMAXX-300 Power 400 Watts, Impedance 4 Ohms with BMX-12 Subwoofer, Chrome-Cone 2,5" (64 mm) Voice Coil AKCIJA -10%!!! CRUNCH Single-Gehusesub CMAXX-12 Power 400 Watts, Impedance 4 Ohms Vented Box with BMX-12 Subwoofer Chrome-Cone, 2,5" (64 mm) Voice Coil

1099,00

1739,99
Subwoofer 30 cm BlackMaxx Serie 806576001249 Single-Bandpass 30 cm BlackMaxx Serie 806576910053 52x39x45/32 cm Dual-Bandpass 2x30 cm BlackMaxx Serie 806576910060 83x39x48/35 cm Subwoofer-Tube 30 cm BlackMaxx-Serie 806576910039 D=34 cm / L=66 cm Vented Box 30 cm BlackMaxx-Serie 806576910046 41x39x45/35

752,00

2120,00

3399,99

1184,00
2-Channel Amplifier CRUNCH AMP DRIVE V-00 1739,00 Drive V Serie 2 x 100 / 150 Watts at 4 / 2 Ohms Drive-V-Serie x 400 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, Herman Josip d.o.o., Tel. +628 229, Fax +628 230, e-mail: josip.herman@ck.htnet.hr, 262x52x287 mm Bandpass-Function, Bass-Boost, VU-Meters Internet stranica: www.hermanjosip.com Strana 2 od 6
CJENIK MALOPRODAJA HRVATSKA SIJEANJ 2008 Proizvod Opis Slika Barkod/Dimenzije Opcija Proizvoda 2-Channel Amplifier Drive-V-Serie 806576230311 262x52x287 mm 2-Channel Amplifier Drive-V-Serie 806576240310 262x52x342 mm 2-Channel Amplifier Drive-V-Serie 806576260318 262x52x423 mm 2-Channel Amplifier Drive-V-Serie 806576280316 262x52x522 mm 4-Channel 4 Channel Amplifier Drive-V-Serie 806576420316 262x52x342 mm 4-Channel Amplifier Drive-V-Serie 806576430315 262x52x423 mm Mono-Block Drive-V-Serie 806576120315 262x52x423 mm Mono-Block Drive-V-Serie 806576180319 262x52x590 mm CRUNCH AMP DRIVE V-x 150 / 225 Watts at 4 / 2 Ohms 1 x 600 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, Bandpass-Function, BassBoost, VU-Meters CRUNCH AMP DRIVE V-x 200 / 300 Watts at 4 / 2 Ohms 1 x 800 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, andpass-Function, Bass-Boost, VU-Meters CRUNCH AMP DRIVE V-x 300 / 400 Watts at 4 / 2 Ohms 1 x 1200 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, andpass-Function, Bass-Boost, VU-Meters CRUNCH AMP DRIVE V-x 350 / 500 Watts at 4 / 2 Ohms 1 x 1600 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, andpass-Function, Bass-Boost, VU-Meters V-4200 CRUNCH AMP DRIVE V x 100 / 150 Watts at 4 / 2 Ohms 2 x 400 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, andpass-Function, Bass-Boost, VU-Meters CRUNCH AMP DRIVE V-x 150 / 225 Watts at 4 / 2 Ohms 2 x 600 Watts max. Power Highpass 10-2500 Hz, Lowpass 40-4000 Hz, Bandpass-Function, Bass-Boost, VU-Meters

2652,00

3399,00

4100,00

3259,00
CRUNCH AMP DRIVE V-1200 Mono-Block 1 x 250 / 500 / 750 Watts RMS at 4 / 2 / 1 Ohms 1 x 1200 Watt max. 3259,00 Power Subsonicfilter 15-55 Hz, Lowpass 40-4000 Hz Bass-Boost 0-12 dB, BassRemote, VU-Meter CRUNCH AMP DRIVE V-1800 Mono-Block 1 x 500 / 750 / 1200 Watts RMS at 4 / 2 / 1 Ohms 1 x 1800 Watt max. 4552,00 Power Subsonicfilter 15-55 Hz, Lowpass 40-4000 Hz Bass-Boost 0-12 dB, BassRemote, VU-Meter
Component Kit 13cm Crunch Drive 2-Wege System CDS5.2C Power 80/160 Watts, Impedance 4 Ohms 25 mm Neodyme-Tweeter, Titanium coated Mylar 12 dB Crossover with Drive-Serie Level Adjustment Installation Depth 55mm, Install.Diameter115 mm 806576522324 Coaxial System 10cm Drive-Serie 806576420323 CRUNCH 2-WEG KOAX DRIVE CDS42CX Power 60/120 Watts, Impedance 4 Ohms 13 mm Neodym-Mylar Tweeter Anodized Blue Cone, Rubber Boot Inst. Depth 50 mm, Inst. Diameter 98 mm

1208,00

494,00
Herman Josip d.o.o., Tel. +628 229, Fax +628 230, e-mail: josip.herman@ck.htnet.hr, Internet stranica: www.hermanjosip.com Strana 3 od 6
CJENIK MALOPRODAJA HRVATSKA SIJEANJ 2008 Proizvod Opis Slika Barkod/Dimenzije Opcija Proizvoda Single-Bandpass 30 CRUNCH SINGLE BANDPASS X-FAT400 Power 400 Watts, Impedance 4 Ohms cm Single Bandpass Box with Plexiglas Fatboy-Serie and blue LED-Illumination x 12" Chrome-Cone FatBoy Subwoofer 48x38x45/32 cm Dual-Bandpass 2x30 cm Drive-Serie 806576910091 83x38x48/38 cm Single-Bandpass 30 cm Fatboy-Serie 806576910114 60x38x45/32 cm Single-Bandpass 30 cm Fatboy-Serie 806576910015 47x39x49/32 cm Single-Bandpass 38 cm Fatboy-Serie 806576910138 49x41x64/39 cm Dual-Bandpass 2x30 cm Fatboy-Serie 806576910022 78x39x49/32 cm Bandpass aktiv 25 cm Drive-Serie 713808504174 31x31x46 cm Bandpass 25 cm Drive-Serie 806576910077 31x31x39 cm Bandpass 30 cm Drive-Serie 806576910152 35x35x46 cm Subwoofer-Tube 30 cm Drive-Serie 7138085022488 D=34 cm / L=66 cm CRUNCH DOPPEL-BANDPASS X-FAT800 Power 800 Watts, Impedance 4+4 Ohms Dual Bandpass Box with Plexiglas and blue LED-Illumination 2 x 12" Chrome-Cone FatBoy Subwoofers CRUNCH SINGLE BANDPASS X-FAT450 Power 450 Watts, Impedance 4 Ohms Single Bandpass Box with Plexiglas and blue LED-Illumination, 2,5" Voice Coil 1 x 12" FatBoy Cast Basket Subwoofer CRUNCH SINGLE BANDPASS X-FAT500 Power 500 Watts, Impedance 4 Ohms Single Bandpass Box with Plexiglas and blue LED-Illumination, 2,5" Voice Coil 1 x XFAT12" Cast Basket Subwoofer CRUNCH SINGLE BANDPASS X-FAT1500 , p Power 800 Watts, Impedance 4 Ohms Single Bandpass Box with Plexiglas and blue LED-Illumination, 3" Voice Coil 1 x XFAT15" Cast Basket Subwoofer CRUNCH DUAL BANDPASS X-FAT1000 Power 1000 Watts, Impedance 2+2 Ohms Dual Bandpass Box with Plexiglas and blue LED-Illumination, 2,5" Voice Coils 2 x XFAT12" Cast Basket Subwoofer CRUNCH Single Gehusesub CAB110 LED aktiv Power 150 Watts, Aktive Subwoofer Bandpass, variable Gain, 80/120 Hz LP High/Low-Inputs, Phase Switch CRUNCH Single Gehusesub CB100 LED Power 250 Watts, Impedance 4 Ohms Single Bandpass Box with Plexiglas Chrome-Cone, blue LED-Illumination CRUNCH Single Gehusesub CB120 LED Power 250 Watts, Impedance 4 Ohms Single Bandpass Box with Plexiglas Chrome-Cone, blue LED-Illumination

2099,00

2272,00

2649,00

3799,00

1740,00

1359,00

1666,00

CRUNCH Tube-Subwoofer DTS 12 Power 300 Watts, Impedance 4 Ohms with DS-12 Subwoofer
CRUNCH SUBWOOFER "FATBOY" DS 12 E Power 400 Watts, Impedance 4 Ohms 1132,00 , Subwoofer 30 cm 50 mm / 2 0" Voice Coil Steel Basket 2,0 Coil, Fatboy-Serie Fs 35 Hz, Qts 0,44, VAS 62 L, 90 dB Herman Josip d.o.o., Tel. +628 229, Fax +628 230, e-mail: josip.herman@ck.htnet.hr, 713808101908Inst. Depth 146 mm, Inst. Diameter 282 mm Internet stranica: www.hermanjosip.com Strana 4 od 6
Subwoofer 30 cm Drive-Serie 806576120322
CRUNCH WOOFER DRIVE CDS-12 828.00 Power 180/300 Watts, Impedance 4 Ohms 50 mm / 2,0" Voice Coil, Steel 599.00 Basket, Fs 24 Hz, Qts 0,27, VAS 145 L, 91 dB Inst. Depth 134 mm, Inst. AKCIJA!!! Diameter 282 mm Akcija vrijedi za vie od dva komada
2-Channel Amplifier Power-Zone Serie 806576910169 260x62x200 mm 2-Channel Amplifier Power-Zone Serie 806576910176 260x62x320 mm 4-Channel Amplifier Power-Zone Serie 806576910190 260x62x320 mm 4-Channel Amplifier Power-Zone Serie 806576910206 260x62x360 mm 4-Channel Amplifier Power-Zone Serie 806576910213 260x62x420 mm CRUNCH NOXX AMP POWER ZONE PZ-125.x 125 / 200 Wattw max. at 4 / 2 Ohms 2 x 75 / 125 Watts RMS an 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 30-250 Hz Bass-Boost 0-12 dB, FullRange Line Outputs CRUNCH NOXX AMP POWER ZONE PZ-200.x 200 / 400 Watts max. at 4 / 2 Ohms 2 x 125 / 200 Watts RMS at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 30-250 Hz Bass-Boost 0-12 dB, FullRange Line Outputs CRUNCH NOXX AMP POWER ZONE PZ-125.x 125/ 250 Watts max. at 4 / 2 Ohms 4 x 75 / 125 Watts RMS at 4 / 2 Ohms Highpass H L 60-1200 Hz, Lowpass H B 30-250 Hz Bass-Boost dB Hi h B t 0-12 dB, Summed Line Outputs CRUNCH NOXX AMP POWER ZONE PZ-175.x 175/ 350 Watts max. at 4 / 2 Ohms 4 x 100 / 150 Watts RMS at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 30-250 Hz Bass-Boost 0-12 dB, Summed Line Outputs CRUNCH NOXX AMP POWER ZONE PZ-225.x 225/ 450 Watts max. at 4 / 2 Ohms 4 x 125 / 200 Watts RMS at 4 / 2 Ohms Highpass 60-1200 Hz, Lowpass 30-250 Hz Bass-Boost 0-12 dB, Summed Line Outputs

1129,00

1899,00
Mono-Block Power-Zone Serie 806576100027 260x62x290 mm
CRUNCH MONO BLOCK POWER ZONE P1000.1D 1 x 350 / 700 Watts RMS at 4 / 2 Ohms 1 x 1000 Watts max. Power Subsonicfilter 20-50 Hz, Lowpass 50-250 Hz Full-Range Line Output, Bass-Remote

3032,00

Mono-Block Power-Zone Serie 806576200024 260x62x380 mm
CRUNCH MONO BLOCK POWER ZONE P2000.1D 1 x 350 / 700 Watts RMS at 4 / 2 Ohms 1 x 2000 Watts max. Power Subsonicfilter 20-50 Hz, Lowpass 50-250 Hz Full-Range Line Output, Bass-Remote

4199,00

Coaxial System 10cm Power-Zone Serie 806576042327 CRUNCH 2-WEG KOAX POWER ZONE PZ42XX Power 40/80 Watts, Impedance 4 Ohms 13 mm Neodym-Mylar Tweeter Paper Honeycomb Cone, Rubber Boot, Inst. Depth 48 mm, Inst. Di t Diameter 98 mm

418,00

Herman Josip d.o.o., Tel. +628 229, Fax +628 230, e-mail: josip.herman@ck.htnet.hr, Internet stranica: www.hermanjosip.com Strana 5 od 6
CJENIK MALOPRODAJA HRVATSKA SIJEANJ 2008 Proizvod Opis Slika Barkod/Dimenzije Opcija Proizvoda Component Kit 13cm Power-Zone Serie 806576502326 Square-Woofer 30 cm Power-Zone Serie 806576101215 CRUNCH POWER ZONE KOMPO PZ5.2CXX Power 50/100 Watts, Impedance 4 Ohms 13 mm Mylar NeodymTweeter, Rubber Boot,12 dB In-Line Crossover Inst. Depth 57 mm, Inst. Diameter 120 mm CRUNCH NOXX SQUARE WOOFER PZ12R Power 300 Watts, Impedance 4 Ohms 50 mm / 2,0" Voice Coil, Steel Basket Fs 29 Hz, Qts 0,36, VAS 70 L, 88 dB Installation Depth 130 mm

899,00

Tube 20 cm Passive CRUNCH NOXX Tube Passiv NTA8Y Power-Zone Serie yellow/red 8" (20 cm) BassTube, 4 Ohm Impedance High Power Woofer 806576112204 with 37 mm Voice Coil 150/300 Watts, with VU-Meter, yellow 74 x 31 cm Tube 20 cm Aktive Power-Zone Serie x 31 cm Coaxial System 10cm Gangsta-Serie
CRUNCH NOXX Tube Aktiv NTP8Y yellow/red 8" (20 cm) Aktive-Bass Tube, Power 150 Watts adjustable Gain, LP, VU-Meter High/Low-Inputs, Switch, Gain 80/120 Hz LP VU Meter High/Low Inputs Phase Switch yellow CRUNCH 2-WEG KOAX GANGSTA G42CX Power 50/100 Watts, Impedance 4 Ohms 13 mm Neodym-Tweeter, yellow Steel Basket, wasserresistant Poly Cone, Rubber Surround, chromed Pole Plates, Multi Array Magnets, Inst. Depth 45 mm, Inst. Diameter 98 mm