Culligan Medallist & Medallist Plus Series Automatic Water Filter Owners Guide
Thank You And Welcome To Your New World Of Better Living With Culligan Water.
The Culligan Medallist Plus Series with Cullar filter has been tested and certified by WQA against WQA S-200 for the effective reduction of chlorine taste and odor up to 180,000 gallons as verified and substantiated by test data. The Culligan Medallist Plus Series with Cullneu filter has been tested and certified by WQA against WQA S-200 for neutralization up to 21,750 gallons as verified and substantiated by test data. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of the system. This system and its installation must comply with state and local regulations. If this is your first experience having filtered, conditioned water in your home, youll be amazed at the marvelous difference it makes. We promise that youll never want to be without it again. Congratulations, too, on selecting one of the first family of water filters in the prestigious Culligan Medallist Series. With Culligans many years of knowledge and experience in water treatment, you can be confident that the model you selected has been designed and engineered to provide years of service with a minimum of care and attention.
Products manufactured and marketed by Culligan International Company (Culligan) and its affiliates are protected by patents issued or pending in the United States and other countries. Culligan reserves the right to change the specifications referred to in this literature at any time, without prior notice. Culligan, Culligan Medallist Series, Cullar, Filtr-Cleer, Cullneu, Accusoft, Culligan Man and www. culligan.com are trademarks of Culligan International Company or its affiliates.
Performance Data Sheets are included in this manual for various Culligan Medallist Series Filter models. Refer to the Performance Data Sheet for your specific filter, as there are slight differences between the models. The filter warranty is located on page 17 of this Owners Guide.

Filter Model

Culligan Medallist Plus Series Cullneu Filter Performance Data Sheet. Page 11
Culligan Medallist Plus Series Cullar Filter Performance Data Sheet. Page 12
Culligan Medallist Series 8 and 10 Cullneu Filter Performance Data Sheet. Page 13
Culligan Medallist Series 8 and 10 Cullar Filter Performance Data Sheet. Page 14
Culligan Medallist Series 8 and 10 Filtr-Cleer Filter Performance Data Sheet. Page 15

Specifications

Medallist 8 General Mineral Tank Size1 Control Timer Temperature Limits Water Pressure Limits Water Pressure Limits (Canada) Electrical Requirements Electrical Power Consumption, Min./Max. Filtr-Cleer Rated Service Flow @ Initial Pressure Drop Minimum Practical Filtration Size Maximum Particulate Matter Maximum Suspended Solids Drain Flow, Maximum3 pH Limitation Recharge Time4 Recharge Water Consumption, Av.5 Freeboard2 Height Overall Cullar Rated Service Flow @ Pressure Drop Drain Flow, Maximum3 pH Limitation Recharge Time4 Recharge Water Consumption, Av.5 Cullar Media Volume Cullsan Underbedding Media Amount Freeboard2 Height Overall Rated Capacity Cullneu Rated Service Flow @ Pressure Drop Drain Flow, Maximum3 pH Limitation* Recharge Time4 Recharge Water Consumption, Av.5 Cullneu Media Volume Freeboard2 Height Overall * Bottom of tank to top of tank fittings. Backwash at 120 psi line pressure. Backwash at 120 psi line pressure. Factory setting. At factory setting and 120 psi line pressure. Top of media to back top edge of port openings. 8 x 44 in. 3/4 Power Valve Electronic 33-120F 20-120 psi 20-90 psi 24V/60 Hz 3 Watts/35 Watts 7.8 gpm @ 15 psi 10 microns 150 NTU 150 mg/L 4.5 gpm 6.0 - 9.min. 100 gal. 10.inches 51 in. 4.0 gpm @ 5.0 psi 2 gpm 5.0 - 11.min. 53 gal. 0.75 cu. ft. 10 lbs. (.1 ft3) inches 51 in. 100,000 gallons 2.7 gpm @ 3.0 psi 3.5 gpm 5.8 - 6.min. 53 gal. 1.0 cu. ft. inches 51 in.

Medallist x 54 in. 3/4 Power Valve Electronic 33-120F 20-120 psi 20-90 psi 24V/60 Hz 3 Watts/35 Watts 8.9 gpm @ 15 psi 10 microns 150 NTU 150 mg/L 7.0 gpm 6.0 - 9.min. 115 gal. 11.inches 63 in. 4.0 gpm @ 5.0 psi 6.0 gpm 5.0 - 11.min. 83 gal. 1.0 cu. ft. 20 lbs. (.2 ft3) inches 63 in. 130,000 gallons 4.0 gpm @ 4.0 psi 6.0 gpm 5.8 - 6.min. 83 gal. 1.5 cu. ft. inches 63 in.
Medallist Plus x 54 in. 1 Power Valve Electronic 33-120F 20-120 psi 20-90 psi 24V/60 Hz 3 Watts/35 Watts 12.0 gpm @ 15 psi 10 microns 150 NTU 150 mg/L 7.0 gpm 6.0 - 9.min. 140 gal. 19 1.5 inches 60 in. 6.0 gpm @ 6.0 psi 6.0 gpm 5.0 - 11.min. 110 gal. 1.5 cu. ft. 20 lbs. (.2 ft3) 24 1.5 inches 60 in. 180,000 gallons 6.0 gpm @ 5.0 psi 6.0 gpm 5.2 - 6.min. 110 gal. 1.6 cu. ft. 18 1.5 inches 60 in.
Under dynamic conditions, it may be necessary to mix five parts Cullneu with one part Cullneu C to effectively raise the pH. The combination of Cullneu and Cullneu C is not certified by WQA.

Filtr-Cleer

The Filtr-Cleer Automatic Water Filter is capable of reducing particulate matter down to 10 microns particle size. It will not remove color, organics, colloidal turbidity or dissolved solids. Some applications follow: Reduction of suspended matters in any water system. Reduction of particulate matter, such as clay, mud, etc. Prefiltration of oxidized iron ahead of an automatic or manual softener. Reduction of light sand. NOTE: If sands cannot be reduced from the Filtr-Cleer tank during backwashing, a sand trap should be installed. After the retention tank when a Cul-Cleer system is used to correct hydrogen sulfide or colloidal suspension problems.

Introduction

The quality and number of gallons filtered water between backwashes will depend upon the amount, type, and size of the particulate matter being filtered. If a water sample is sent to our laboratory, where application of a Filtr-Cleer unit is contemplated, write Filtr-Cleer Analysis on the sample tag. Send an additional sample of water for a standard water analysis. The laboratory will test for Nephelometric Turbidity Units (NTU) and suspended solids (mg/L). The sample will also be filtered through 10 micron filter paper and NTU run on a filtered sample. If the NTU of the raw water exceeds 150, suspended solids exceed 150 mg/L or the filtered water through the 10 micron filter paper is of an unacceptable quality, a Filtr-Cleer filter may not be applicable. As a guide, the U.S. Public Health Drinking Water standards states the turbidity should not exceed 1 NTU. The exact number of gallons filtered between backwashes cannot be given because of many variables.

Cullar Filter

Medallist Water Filter with Cullar Media will reduce chlorine taste and odor and other common bad tastes and odors, and will also reduce most objectional organic colors. It will not remove hydrogen sulfide. It is important to note that whenever the cause of an objectionable taste or odor has not been established, Health Authorities should determine if water is safe to drink. If bacterial contamination is present, a Cul-Cleer system is indicated. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Cullneu Filter

Medallist Water Filter with Cullneu Media will neutralize slightly acid water (pH of 5.8 - 6.2) and thus help to prevent unsightly brown or green stains due to corrosion of household plumbing. If the pH is from 5 to 6, one part of Cullneu C media should be mixed with 5 parts of Cullneu media to provide additional neutralizing capability. If the water to be treated has a pH less than 5, a high hardness, or a high carbon dioxide level, Cullneu may not be applicable; a solution feeder should be used. Since Cullneu adds hardness, it should be used prior to a softener. In order to size and apply the equipment correctly, a complete analysis of the water supply should be obtained. This can best be accomplished by contacting your local Culligan dealer, who will be able to test the water supply right at the site, or arrange to have one or more water samples sent to the Culligan laboratory for a more detailed analysis.

Familiarization

Power Loss
The AccuSoft circuit board is equipped with a Hi-Cap Capacitor and EEPROM memory chip. The capacitor is capable of maintaining the time, for at least two days, in the event of a power outage. The EEPROM ensures that the individual programming parameters of your filter are not lost. If the power outage lasts long enough to drain the Hi-Cap Capacitor, the control will flash 12:00 PM when power is returned to the control. The unit will continue to keep time from the moment power is restored, and will initiate a full regeneration at the preset regeneration time. The time of day will need to be reset in order to return the regeneration to its preset time. If you live in an area where power outages occur with a regular frequency, a battery backup option is available for ensuring that the time of day is properly maintained. Contact your Culligan Dealer for more information.

Regeneration

To initiate a regeneration at the preset time, press the REGEN button. The REG light will light. To initiate an immediate regeneration, press and hold the REGEN button for at least five seconds. The REG will light and blink. An immediate regeneration will also occur if a power outage has lasted for more than four hours and the Immediate Regeneration option is chosen. Ask your Culligan Dealer about this feature. A regeneration at the Time of Regeneration will occur if so signaled by the Soft-Minder meter. The REG enunciator on the display will also be lit.

Service

The Culligan Medallist Series water filter is equipped with a self diagnostic program to insure optimal operation of your water filter. Should service become necessary, a phone icon will appear in the display. If this condition occurs, call your local Culligan Dealer for assistance. The phone icon and error code will be the only items displayed when service is required on the control.
Setting the Microprocessor
The microprocessor senses when it is installed as a Soft-Minder control. Adding or removing any connection to the board will automatically reset the microprocessor to the factory settings. Step 1 Programming Time of Day Press the STATUS key. The display will blink tod for 3 seconds and then change to time of day with the minutes digits blinking. Adjust the minutes digits with the + or - keys. Press the REGEN key to blink the hours digits. Adjust the hours digits with the + or - keys. Press the REGEN key to cycle back to minutes Note: The hours setting scrolls through 1-12 and 1-12 PM. Make sure the proper AM or PM indicator is shown when setting the time (AM is not displayed).

Programming

12:00 2:10
Step 2 Programming Regeneration Time Press the Status key after setting the time of day. The display will blink tor for 3 seconds and then change to the time setting with the ones digit blinking. Adjust regeneration time as time of day above. Note: This option will not show if the dIP 2 option is set to immediate

Step 3 Programming Backwash Time Press the Status key after programming tor. The display will blink bw for 3 seconds and then display the backwash time in minutes. Adjust the setting with + or - key. (1-40 minutes)
Step 4 Programming Fast Rinse Time Press the STATUS key after programming the backwash time. The display will blink Fr for 3 seconds and then display the Fast Rinse Time in minutes. Adjust the setting with + or - key. (5-30 minutes)

Programming (cont.)

Step 5 Days to Regeneration with Fast Rinse Press the STATUS key after programming the fast rinse time. The display will blink CAP for 3 seconds and then display the number of days between regenerations. Adjust the setting with the + or - key. (1-42 days) Exiting Program Mode From Step 5 press the Status key. The display will go blank. Press the Status key again to exit programming. Note: The control will exit the programming mode if no key press activity takes place within one minute.
Troubleshooting The Culligan Medallist Series Filter is equipped with an advanced error detection system. During all operating modes the filters electronics are performing self-diagnostics to ensure that the unit is operating correctly. There may be times, however, when something may occur that could cause the unit to improperly operate. In those instances the microprocessor will identify the exact problem and alert the user with a telephone handset symbol in the upper left corner of the display and the error code will be shown. Shown below is codes that would appear if an error is detected. Display E1 E2 E3 Error Description Motor will not stop turning Motor stuck Wrong position Response Call Culligan service technician Call Culligan service technician Call Culligan service technician
If an error code appears that requires an authorized service technician please contact your local Culligan Dealer. For any additional troubleshooting or service needs please contact your local Culligan Dealer.
If you unexpectedly experience problem water, make these simple checks before calling your Culligan dealer. One of the following conditions may be the reason for your interruption of service.

Important

If any of the following conditions is found, the water filter should be manually recharged according to instructions on page 5 after you have corrected the problem.

Things to Check Before You Call For Service

Power Supply

Check your power supply cord. Is it plugged fully into the electric outlet? Be certain that the outlet is not controlled by a wall switch which has been turned off. Reset conditioner to proper time of day and then plug in.

Blown Fuse

Check the house fuse or circuit breaker panel. Replace a blown-out fuse or reset an open circuit breaker.

Power Failure

Any interruption in your power supply or time changes - such as daylight savings - will disrupt your filters recharge schedule by causing the timer to run off-schedule. Reset timer to proper time of day.

Bypass Valves

Check to see if they are in the proper position. Cul-Flo-Valv Bypass, if used, should be in the Push for Service position. If hand valves are used, see that inlet and outlet valve are opened and that the bypass valve is closed.

No Water

If you arent getting any water flow at all, make sure your water supply is working. Open a tap ahead of the filter (outside tap) to see if you have any water pressure. If you have water pressure, check the bypass valve. If it is in the Service position, put it into the bypass and call your Culligan dealer for service.

Increased Usage

Guests, family additions, new water-using appliances, etc., all will result in more water usage and will require more capacity from your filter. You can reprogram your recharging schedule by following the directions on pages 7 and 8. Call your Culligan dealer for advice and save a service call.
When & How to Bypass Your Water Filter
Normally, all water except outside lines passes through the water filter. There are times when the water filter should be bypassed, using the push-button Cul-Flo-Valv Bypass, or a 3-way bypass valve. You should bypass: 1. If lines to outside faucets do not bypass the water filter, and you do not want to waste filtered water on lawn sprinkling or other outside uses. 2. If you are going away on vacation and want to save water by not having the unit recharge while youre away.
Medallist Series Bypass Valve

Culligan Bypass Valve

In the back of Culligan water conditioners is a push-button Cul-FloValv Bypass. To bypass unit, simply turn the blue knob clockwise. To return to soft water service, reverse the procedure - turn the blue knob counterclockwise. To BYPASS, turn the blue knob clockwise (see directional arrow on end of knob) until the knob stops as shown. DO NOT OVERTIGHTEN! To return to SERVICE, turn the blue knob counter-clockwise (see directional arrow on end of knob) until the knob stops as shown. DO NOT OVERTIGHTEN!

Bypassed

About 1-1/4

Soft Water

A screwdriver shank may be used in the slot as a lever for extra turning force if needed.

Culligan Medallist Plus Series 10 With Cullneu Filter
Important Notice Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit. Culligan knows the more informed you are about your water treatment system, the more confident you will be about its performance. Its because of this and more than seventy years of commitment to our customers that Culligan is providing this Performance Data Sheet to its customers. Manufacturer Substance Reduction This system has been tested according to WQA S-200 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in WQA S-200. While testing was performed under standard laboratory conditions, actual performance may vary.
Substance pH USEPA SDWA* SMCL 6.5 - 8.5 Average Test Influent Concentration Level 4.6 mg/L Average Test Effluent Concentration Level 7.1 mg/L

Performance Data Sheet

Culligan International Company 9399 W. Higgins Rd., Suite 1100, Rosemont, IL 60018 USA 1-800-CULLIGAN or 1-847-430-2800
* United States Environmental Protection Agency Safe Drinking Water Act. Capacity: 21,750 gallons Flow Rate: 6.0 gpm Rated Pressure Drop:6.0 gpm @ 5 psi Operating Conditions Water Pressure Limits:20 - 120 psi (140 - 860 kpa) Canada: 20 - 90 psi (140 - 620 kpa) Temperature Limits: 33 - 120 F (1 - 50 C) Electrical Characteristics: 120V/ 60 Hz, 45 Watts
This filter is tested and certified by WQA against WQA S-200 for neutralization up to 21,750 gallons for the Medallist Plus 10 Cullneu as verified and substantiated by test data. Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Regeneration Frequency: Replacement frequency will vary with water conditions. Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

Buyer Signature _ ________________________________________________ Date _ ________________ _ Seller Signature _ ________________________________________________ Date _ ________________ _ 11
Performance Data Sheet (cont.)
Culligan Medallist Plus Series 10 With Cullar Filter
Substance Chlorine Taste & Odor USEPA SDWA* SMCL N/A Average Test Influent Concentration Level 2.11 mg/L Average Test Effluent Concentration Level 0.02 mg/L
* United States Environmental Protection Agency Safe Drinking Water Act. Capacity: 180,000 gallons Flow Rate: 6.0 gpm Rated Pressure Drop:6.0 gpm @ 6 psi Operating Conditions Water Pressure Limits:20 - 120 psi (140 - 860 kpa) Canada: 20 - 90 psi (140 - 620 kpa) Temperature Limits: 33 - 120 F (1 - 50 C) Electrical Characteristics: 120V/ 60 Hz, 45 Watts
This filter is tested and certified by WQA against WQA S-200 for neutralization up to 180,000 gallons for the Medallist Plus 10 Cullar as verified and substantiated by test data. Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Regeneration Frequency: Replacement frequency will vary with water conditions. Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.
Buyer Signature _ ________________________________________________ Date _ ________________ _ 12 Seller Signature _ ________________________________________________ Date _ ________________ _
Culligan Medallist Series 8 and 10 With Cullneu Filter
Substance pH USEPA SDWA* SMCL 6.5 - 8.5 Average Test Influent Concentration Level 4.3 mg/L Average Test Effluent Concentration Level 8.0 mg/L
* United States Environmental Protection Agency Safe Drinking Water Act. Capacity: 13,500 gallons (8 Filter) 20,000 gallons (10 Filter) Flow Rate: 2.7 gpm (8 Filter) 4.0 gpm (10 Filter) Rated Pressure Drop:2.7 gpm @ 3 psi (8 Filter) 4.0 gpm @ 4 psi (10 Filter) Operating Conditions Water Pressure Limits:20 - 120 psi (140 - 860 kpa) Canada: 20 - 90 psi (140 - 620 kpa) Temperature Limits: 33 - 120 F (1 - 50 C) Electrical Characteristics: 120V/ 60 Hz, 45 Watts Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Regeneration Frequency: Replacement frequency will vary with water conditions. Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water. Buyer Signature _ ________________________________________________ Date _ ________________ _ Seller Signature _ ________________________________________________ Date _ ________________ _ 13

Culligan Medallist Series 8 and 10 With Cullar Filter
* United States Environmental Protection Agency Safe Drinking Water Act. Capacity: 100,000 gallons (8 Filter) 130,000 gallons (10 Filter) Flow Rate: 4.0 gpm Rated Pressure Drop:4.0 gpm @ 5 psi Operating Conditions Water Pressure Limits:20 - 120 psi (140 - 860 kpa) Canada: 20 - 90 psi (140 - 620 kpa) Temperature Limits: 33 - 120 F (1 - 50 C) Electrical Characteristics: 120V/ 60 Hz, 45 Watts Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Regeneration Frequency: Replacement frequency will vary with water conditions. Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water. Buyer Signature _ ________________________________________________ Date _ ________________ _ Seller Signature _ ________________________________________________ Date _ ________________ _ 14
Culligan Medallist Series 8 and 10 With Filtr-Cleer Filter
Substance Class III Particulate Particles > 5 - < 15 m Average Influent Challenge Concentration 45,746 particles/mL Reduction Required > 85% Average % Reduction 91.8% Minimum % Reduction 88.8%
Capacity: ? Flow Rate: ? Rated Service Flow at Pressure Drop: 7.8 gpm @ 15 psi (8 Filter) 9.0 gpm @ 15 psi (10 Filter) Operating Conditions Water Pressure Limits:20 - 120 psi (140 - 860 kpa) Canada: 20 - 90 psi (140 - 620 kpa) Temperature Limits: 33 - 120 F (1 - 50 C) Electrical Characteristics: 120V/ 60 Hz, 45 Watts Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Regeneration Frequency: Replacement frequency will vary with water conditions. Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water. Buyer Signature _ ________________________________________________ Date _ ________________ _ Seller Signature _ ________________________________________________ Date _ ________________ _ 15

Records and Data

Important Data on Your Water Filter
It is advisable to have the salesperson or installer fill in the information below for your future reference. If this has not been done, please ask for it, as it is necessary if you contact your dealer.

Identification

Model Name ______________________________ Control Model No. _ ________________________ Date of Installation __________________________ Catalog No. ________________________________ Control Serial No. ___________________________ Tank Serial No. _ ____________________________

Settings

Time of Recharge: _____________ a.m. ________________ p.m.
Regeneration Interval ________________ days (Time clock models) Gallons to signal ________________ gallons (Soft-Minder models) Number of people in household ___________________________________________________________ ___

Water Analysis

Total Hardness __________ (gpg) Total Iron __________ (ppm) pH (acidity)_______________
Other __________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________
Culligan Medallist Series Automatic Water Conditioners
You have just purchased one of the finest water conditioners made. As an expression of our confidence in Culligan International Company products, your water conditioner is warranted to the original enduser, when installed in accordance with Culligan specifications, against defects in material and work manship from the date of original installation, as follows: For a period of ONE YEAR For a period of FIVE YEARS For a period of TEN YEARS The entire conditioner The AccuSoft circuit board, or Soft-Minder meter, if so equipped. The control valve body, excluding internal parts. The conditioner tank
Culligan Limited Warranty
If a part described above is found defective within the specified period, you should notify your inde pendently operated Culligan dealer and arrange a time during normal business hours for the dealer to inspect the water conditioner on your premises. Any part found defective within the terms of this warranty will be repaired or replaced by the dealer. You pay only freight from our factory and local dealer charges. We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not meet Culligan specifications, is not covered by this warranty. Refer to the specifications section in the Installation and Operating manual for application parameters. Our product performance specifications are furnished with each water conditioning unit. To the extent permitted by law, culligan disclaims all implied warranties, including without limitation warranties of merchantability and fitness for particular purpose; to the extent required by law, any such implied warranties are limited in duration to the one-year period specified above for the entire conditioner. As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing a water conditioner. The quality of water supplies may vary seasonally or over a period of time, and your water usage rate may vary as well. Water characteristics can also differ considerably if your water conditioner is moved to a new location. For these reasons, we assume no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us. Further, we assume no liability and extend no warranties, express or implied, for the use of this product with a non-potable water source. Our obligations under this warranty are limited to the repair or replacement of the failed parts of the water conditioner, and we assume no liability whatsoever for direct, indirect, incidental, consequential, special, general, or other damages. Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly, some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Consult your telephone directory for your local independently operated Culligan dealer, or write Culligan International Company for warranty and service information.

Culligan International Company
9399 W. Higgins Rd., Suite 1100 Rosemont, IL 60018 USA 1-800-CULLIGAN or 1-847-430-2800 www.culligan.com
With Culligan You Get More Than a Quality Product
You Get Your Water Expert, The Culligan Man
Were here to provide you with fast, dependable service, making sure any problems you have are taken care of. The Culligan Man has been around for over seventy years, delivering dependable service all along. Thats why people say Hey, Culligan Man! Because were the water experts. And thats who you want taking care of your water.

The Culligan Promise

At Culligan, we understand that a water quality improvement system is an investment in your familys well-being. Thats why our 1,350 independently operated dealers worldwide dont just sell products; they sell water quality you can count on. We stand behind our products with written limited warranties and our unequaled Culligan service. No matter where you live, you can depend on Culligan expertise to work for you today and tomorrow.
2007 Culligan International Company

01017642C

This page contains materials and DCO information. IT DOES NOT PRINT AS PART OF THE DOCUMENT!
Materials & Description: Medallist Filter Series Owners Guide Size: Color: Stock: Other: 11 x 17 Black, 2 Sided 20# White Collate, Bookletmaker (Fold to 8 1/2 x 11) Saddle Stitch with 2 Staples Standard 3 Hole Drill

01017642

Let A B1 B2 C1
Change New Art Created Update WQA-move to 8780 Update Art Regl. Update

By LR LR LR LR

Aprvd JS JS JS JS

DCO 8780 10083

Date 07/30/04 08/22/05 11/21/06 06/04/07