User guide

CALYBOX

Energy manager

6050388 CALYBOX 110 - 1 zone 6050389 CALYBOX 120 - 2 zones

http://pro.deltadore.com

DELTA DORE TALCO - Bonnemain - 35270 COMBOURG E-mail : deltadore@deltadore.com
Device complying with the requirements of the directives: CEE 89/336 (Electromagnetic compatibility) and CEE 73/23 modified CEE 93/68 (Low voltage safety) Because of changes in standards and equipment, the characteristics given in the text and the illustrations of this document are not binding unless confirmed by our services.

*2701550_Rev.1*

Presentation
This unit optimizes the energy management of your home: Comfort or Economy mode programming of the heating for 1 zone (CALYBOX 110) or 2 zones (CALYBOX 120), reduction in the subscription costs by preventing the circuit-breakers from tripping when the electricity consumption is too great (load shedding), indication of the electricity consumption of the system. To control the heat emitters, the programmer uses the Pilot Wire.
Heat emitters Programmer Pilot Wire orders
The required temperature is set on the thermostat of each heat emitter (convectors, panel heaters, underfloor heating or radiant ceiling heating, towel warmer radiators, storage heaters, etc.).

Pilot Wire order (mode)

Comfort
Setting on the heat emitter
Comfort setting (thermostat knob) example : 19C Economy setting (thermostat knob) example : 16C or Comfort XC (depending on heat emitter model) Frost protection set to 7C or 8C (depending on model) Heating shutdown

Room temperature

Economy

Absence

7C or 8C

Shutdown

No heating

Pilot wire

Independent from the power supply of the heat emitter, the Pilot Wire is used to send the Comfort , Economy , Frost Protection or Shutdown orders requested by the programmer.
IMPORTANT: The heat emitter must be in automatic mode (PROG, AUTO, , etc. depending on model).

Warnings

Carefully read these instructions prior to use. Do not attempt to repair the unit yourself; aftersales service is available.

Contents

Description.6 Automatic mode.7 Override.8 Timer mode.9 Continuous mode.10 Absence mode.11 Shutdown mode.12 Information button.13 Time setting.15 Programming.16
1. Create your program.16 2. Copy the program.16 3. Confirm the program.16

Options

TYWATT 500 (ref. : 6110014) Depending on your installation, the TYWATT 500, together with the CALYBOX, allows you to know the electricity consumption (in euros) of the heating, the water heater (DHW) and other electrical appliances (lights, household appliances, etc). TYPHONE 500 (ref. : 6201029) Combined with the CALYBOX, the TYPHONE 500 is used to control the heating system and the water heater (DHW) remotely by telephone. MINOR 500 (ref.: 6151041) Regulates an underfloor heating or radiant ceiling heating system. In combination with the CALYBOX, this unit is used to control the set points and determine the room temperature measured by each probe.

MINOR 500 option.19 Tempo tariff.20 Troubleshooting.21

Description

These instructions apply to both CALYBOX 110 and CALYBOX 120.

Automatic mode

Turn the knob to AUTO. CALYBOX 110 follows the programming.
Time Current mode Current day Override
Modification buttons Selector knob position
Room temperature Information button Display in automatic mode

Selector knob

CALYBOX 120 follows the programming in both zones.
Time Current day Current mode in zones 1 and 2 Override for zone 1 Override for zone 2 Room temperature Information button Display in automatic mode
Shutdown mode Absence mode Timer mode Automatic mode Continuous mode

Time setting Programming

Override
In automatic mode, override is used to go from Comfort to Economy mode (or conversely) until the next program change. Example: it is 15:30 and you would like to switch to Comfort mode before the set time (17:00).

6:00 8:00

Timer mode
This mode is used to select a mode for a given time and for one zone only. Turn the knob to.
Choice of the zone on the CALYBOX 120 (the other zone follows the AUTO mode)) Confirm Current day programming on zone 1 Press the override button of zone 1. Choice of mode: Economy or Comfort Confirm

15:30 17:00

23:00 00:00
Current override on zone 1.
Adjustment of the duration from 15 minutes to 72 hours (in increments of 15 minutes) Confirmation and start of the countdown
To cancel the current override, press the button once more.
At 17:00, the program will return to its usual program.
To cancel the current timer mode, turn the knob.
Return to AUTO mode at the end of the countdown

Continuous mode

This mode allows you to choose a continuous mode for each of the zone. Turn the knob to , then press the modification button of the relevant zone to select the Comfort or Economy mode. CALYBOX 110

Current mode Modification of the mode

Absence mode

This mode lets you place your home under Frost Protection if you need to leave for several days Turn the knob to.
Adjustment of the number of days (1 to 365) Example: for a departure on 1 March and a return on 10 March, program 9 days of absence. Automatic operation will resume on 10 March at midnight. Confirm and start the calendar countdown.

CALYBOX 120

Current modes in zones 1 and 2 Modification of the mode in zone 1 Modification of the mode in zone 2
To cancel the current absence mode, turn the knob.
To exit this mode, turn the knob.
NOTE: The water heater (DHW) is shutdown during the absence mode. If you want the water heater to be in automatic mode, refer to the installation guide or contact your installer or our customer service department.

- 10 -

- 11 -

Shutdown mode

This mode allows you to shut down your heating system (in this case, the water heater stays in automatic mode). Turn the knob to.

Information button

During the AUTO, or modes, press the i button repeatedly to find out: total consumption of your installation,
Reset Room temperature Consumption

Press successively

to reset, press and hold the init. button for 5 seconds. if you have the TYWATT 500 option, the electrical consumption in euros of the heating, the water heater (DHW) and other electrical appliances (lights, household appliances, etc).

Mise zro Mise zro

- 12 -

- 13 -

the program of the current day per zone,

Time setting

Turn the knob to. The days flash. Press + or - to change the day, then press OK to confirm and continue on to the next setting.

Minutes Days

(1 : Monday 7 : Sunday)

Comfort periods

if you have the MINOR 500 option, the temperature measured by each of the probes declared during the installation.

probe no.

Repeat the operations to set the hours and minutes.
temperature measured by the probe
To leave the setting the time mode, turn the knob.
Indication of a probe or probes on the installation
NOTE: If the unit is configured for a daily program, the days setting is not offered.

- 14 -

- 15 -

Programming

Turn the knob to PROG. The default program is a Comfort period from 6:00 to 23:00.
Example: Comfort from 6:00 to 8:00 and from 17:00 to 23:00
6:00 8:00 17:00 23:00 00:00

1. Create your program

Programming starts on day 1 at midnight. Press the or buttons to create different Economy or Comfort periods

Day Available on the CALYBOX 120 1st time slot Comfort period adjustment Economy period adjustment
Press until you reach 6:00 Press until you reach 23:00

until you reach 8:00

until you reach 00:00
2. Confirm and copy the program
Press and hold the OK button for 3 seconds to confirm the program you created and copy it to the next day.

3. Confirm the program

Press the OK button to confirm and continue on to the next day to program it separately.
Press until you reach 17:00 Copy and confirm or confirm

- 16 -

- 17 -
Programming Check your program
Press the button repeatedly to check the accuracy of the Comfort and Economy periods you created.

Time slot consulted

MINOR 500 option: set point settings
This mode is used to modify the Comfort and Economy set points of each probe. Turn the knob to.
Setting (5 to 30C) of the Comfort set point (19C by default) for the probe 1 of zone 1. Confirm and go to the next setting.

Program profile

Verification of the different or periods
Setting (5 to 30C) of the Economy set point (16C by default) for the probe 1 of zone 1. Confirm and go to the set point settings for the next probe.
Programming zone 2 (on the CALYBOX 120) The programming for zone 2 is available after pressing (OK) of the day 7 of the zone 1 Exiting the programming mode
Turn the knob to another mode COMMENTS: Depending on the configuration made during installation, programming can be weekly or daily. Likewise, this programming may be done in increments of one hour, 30 minutes, or 15 minutes. To change these settings, refer to the installation guide, or contact our customer service department or your installer.
Repeat the operations for each probe. When the last probe is set, you can set the Frost Protection set point for all the zones.
Setting (5 to 15C) of the Frost Protection set point (8C by default) for all the zones. Confirm the modification
To exit the mode, turn the knob to another mode.

- 18 -

- 19 -

Tempo tariff

If you are on the tempo tariff, you can program specific modes for peak or off-peak days according to the configuration made during installation. To know or change these settings, refer to the installation guide, or contact our customer service department or your installer.

Troubleshooting

The purpose of this section is to help you quickly solve the most common problems that you may encounter with your product during use. If you're unsure, or if the problem persists or isn't in this list, contact our customer service department.
Nothing is displayed on the room unit screen. There is no power supply. Check your circuit breaker.
Tariff reduction in progress
The i symbol flashes. A fault has been detected in the system. Press the button to consult the fault or faults. The unit displays: dEF and a number. There is a fault on the unit or the installation. Contact your installer or our customer service department. The unit displays ---- instead of the temperature measured by each MINOR 500 probe. There is a communication problem with the probes. Contact your installer or our customer service department. The unit is in time setting mode. There was a mains disruption that lasted more than 2 hours. Set the time. All other settings have remained unchanged.

The symbol flashes during a tariff reduction. The symbol flashes if you are in Mdio (1C) or Modrato (-2C) comfort mode

- 20 -

- 21 -
The symbol and flash. You are in tariff reduction mode. Refer to the Tempo tariff section. When setting the time, there is no option to set the day. You are in daily programming. To switch to weekly programming, refer to the installation guide or contact your installer or our customer service department. The consumption displayed by the unit does not correspond to the consumption shown on the bill sent by the electricity supplier. The consumption value that you can read on the unit is a non-contractual indication and cannot be substituted for the consumption value mentioned on your electricity suppliers bill. Refer to the installation guide to check the price per kWh or contact your installer or our customer service department. The heating elements are in Frost Protection mode You are in programming mode, the absence mode or time setting mode. Turn the knob to select another mode. Pb ---- is displayed on the screen. Problem with the connection of a heating element. Contact your installer or our customer service department.
The unit displays HEAT Your underfloor heating or radiant ceiling heating system is in gradual heating mode. If you want to know the number of days remaining, press the i button. The temperature displayed does not match the temperature measured in the room (thermometer). It is possible to correct this. Refer to the installation guide or contact your installer or our customer service department.

- 22 -

- 23 -