Installation guide

DRIVER 230 CPL

3 zone weekly programmer using power line carriers
Device complying with the requirements of the directives: 2004/108/CE (electromagnetic compatibility) and 2006/95/CE (low voltage safety).

*2701972_Rev.1*

DELTA DORE - Bonnemain 35270 COMBOURG - FRANCE E-mail : deltadore@deltadore.com

Contents

Characteristics. 3 General principle. 4 Installation. 6 Connection. 7 Starting up. 8 Price programming. 12 Wireless option. 14
Associating a door/window magnetic contact. 14 Associating a TYXAL alarm control unit.. 15 Associating a TYDOM 200 remote control. 16 Associating a TYXIA remote control.. 17 Associating a telephone transmitter TYDOM 300.. 19 Deleting all wireless associations.. 19

Characteristics

230 V, 50 Hz power supply, 10% Clock back-up in the event of mains outage: 4h (per condenser) Programming saved permanently Power consumption: 4 VA Class II insulation Operating mode selector knob (9 positions) Selection of 4 continuous modes (Frost Protection, Economy, Comfort, Shutdown) and 1 customizable program by day and by zone Override with automatic return Programmable (1 to 99 days) or continuous frost protection Carrier frequency: 132.5 kHz, FSK modulation, X2D protocol Compliant with the NF EN 50065 standard, class 122 "Home" addressing: 65000 factory-coded combinations Digital display Room unit: 124 x 95 x 43 mm Wall mounting on flush-mounted box or projecting Protection index: IP 30 Installation in an environment with normal pollution levels Compatible with the TYDOM 520 for adding home automation functions Operating temperature: 0 to 40C Storage temperature: -10C to +70C
Because of changes in standards and equipment, the characteristics given in the text and the illustrations of this document are not binding unless confirmed by Delta Dore.
General principle Power line carrier transmission
The principle of PLC transmissions is to stack an encoded signal with a higher frequency and weaker amplitude on the signal present between the live and neutral wires (230 V, 50 Hz). DRIVER 230 CPL can be used in blue tariff installations with an area less than 180 m.

Electronic meter

ECS CPL
Marche Arrt Dlestage Normal Config. OK Dfaut Dfaut OK

CHAUFFAGE

Transmitter

Carrier frequency

GP4 CPL

Receiver

remote-info

230 V mains network

DRIVER CPL programmer

GP4 CPL (optional)

1 DHW output

Receivers

They are of the following types: - TC51089 "Pilot Wire" for controlling 6-order pilot wire convectors (GIFAM standard). - X2D PLC reception circuit boards of various convector manufacturers - X2D PLC radiators
The quality of the comfort temperature control depends on the quality of the convector thermostat.

Mains supply

Electric water heater
TC51089 PLC receiver (not supplied)

Convectors zone 1

Convectors zone 2

Convectors zone 3

Phase coupler
In three-phase installations, you must use a phase coupler to transmit on the 3 phases simultaneously.

N Ph1 Ph2 Ph3

Installation Positioning options
The driver can be installed anywhere in your home. That said, having it within reach for programming is an advantage.

Connection

- Standard UTE NF C15-100 and good practice must be complied with. - Connected or nearby equipment must not generate excessive interference (directives 2004/108/CE).
Switch off the mains power before handling the device.

Mounting

To mount the unit on the wall, it must be separated from its base. Once separated from the case, the base must be wall-mounted with screws and plugs or installed in a flush-mounted box (distance between centres 60mm) using the holes. Knockout partitions are provided for passing the connection wires ( : for flush-mounted box, : for wall-mounting)

Connect the two power leads to the terminal. Replace the device on its base and attach it with the tightening screw.
For a projecting mounting, the cable (2 wires, class 2) must reach the unit via a cable duct. Switch on the installation.
When the installation is switched on for the first time, the display will only appear after around 30 sec. (back-up capacitor charging period). Only an hourglass flashes at this time. Note: To protect the DRIVER CPL power supply, you must use a 10 A circuit breaker at least (do not use a 2 A circuit breaker).

Starting up

Startup mode enables the PLC products to be combined amongst themselves and the installation organisation to be determined (transmitters, receivers, pilot wire type, load shedding, etc.). Note: You may only define one type of pilot wire for each zone.
3 Associating Driver 230 with

a transmitter

On the DRIVER 230 CPL, you can associate a PLC transmitter type device (GECPL1, GP4 CPL, TYPHONE 2 CPL, etc.). Otherwise, confirm to move onto the next step 4 The unit displays EMET alternating with ----. To associate an energy manager type transmitter (GECPL1, GP4 CPL, etc.) Confirm on the transmitter (see the relevant guide). The display reads GE--. Note: Press to cancel.

1 Enter startup mode.

Turn the knob to. Set the clock if necessary (see user guide) or press to move onto the next step. The unit displays PArA.
2 Determining the type of pilot wire
Press the and buttons simultaneously. The unit displays FP4 (4-order pilot wire) or FP6 (6 order pilot wire) for zone 1. Press the and buttons to determine the type of pilot wire used, then press validate. Repeat the operation for zones 2 and 3. to
To associate a PLC telephone remote control type transmitter (TYPHONE 2 CPL) Confirm on the transmitter (see the relevant guide). The display reads --TL. Note: Press to cancel. If DRIVER 230 CPL is associated with 2 types of transmitter, the display reads GETL. Press to confirm your choice and move on to the next stage.
4 Allocation of receivers
You must associate each receiver to the central control unit and you can determine the load-shedding channel to which it is allocated (if DRIVER 230 CPL is associated with an energy manager: GECPL1, GP4 CPL, etc.).

4.2 The unit is not associated with a GECPL1, GP4 CPL, etc.
Indication of the relevant heating zone
The "EMET" screen flashes.
4.1 The unit is associated with a GECPL1, GP4 CPL, etc. Press or to select the load-shedding channel to
which the receivers will be allocated. The load-shedding channel can be selected from d:0 to d:6 (d:0 = no load shedding). For use with GECPL1, channels d4, d5 and d6 must not be allocated (no load-shedding).
Selecting the load-shedding channel Indication of the relevant heating zone
The identification of the relevant heating zone is displayed.
Confirm on the zone 1 receivers Press Press Press
. The unit goes to zone 2.
Confirm on the zone 2 receivers.
. The unit goes to zone 3.
Confirm on the zone 3 receivers.
to confirm and exit the mode.
Confirm on the relevant receivers. Repeat operations and for the receivers allocated to
another load-shedding channel to confirm your selection and move onto zones 2 and 3. Repeat the operation. Press to confirm and exit the mode.

Press

- 10 -

- 11 -

Price programming (only in tempo option)
The Driver 230 CPL must be combined with a GECPL1 or GP4 CPL energy manager. Price programming is used to select a lower temperature (economy) in periods when electricity is most expensive (e.g. peak hour period, Red day). Prices are programmed using the programs of the electronic meter.
Operating Mode Applicable in Economy Periods
Turn the knob to Press. to display PArA. to enter the price reduction

Z1 Z2 Z3

Press again setting mode.
BLUE day Off-peak Hours CHAU 0 CHAU 1 CHAU 2 CHAU 3 CHAU 4 CHAU 5 CHAU 6 CHAU C Peak Hours
WHITE day Off-peak Hours Peak Hours
RED day Off-peak Hours Peak Hours
By pressing the or buttons, select the mode desired for a price reduction in zone 1 (Economy, Comf -2C, Comf -1C, Comfort (no reduction)). Note: The Comfort -1C and Comfort -2C modes are only available with 6-order pilot wire heating. Press to validate and move onto zones 2 and 3
Repeat the operation, then confirm with The unit displays the time.
Period with active price reduction

- 12 -

- 13 -

Wireless option

The TYDOM 520 wireless module lets you associate the following home automation functions: - operation with a door/window magnetic contact, - operation with a TYXAL alarm central control unit - operation with TYXAL remote controls (Delta Dore), - operation with a home automation transmitter (example: TYDOM 300). On the Driver CPL, rAdio is no longer displayed. The door/window magnetic contact is associated with the Driver CPL. Repeat the association operation to associate another door/window magnetic contact. Note: it is possible to associate up to 16 home automation products (detectors, emitters, etc.).

Installing the module

Separate the unit from its base. Put the module in its place. Close up the unit.
Associating a TYXAL alarm control unit
To set the control unit to Maintenance mode. Simultaneously press the ON and OFF buttons on the remote control for 5 seconds and open the control unit cover.
Open the battery cover of the control unit

5 sec.

1234 567
Associating a door/window magnetic contact
To associate your Driver CPL with a door/window magnetic contact On the Driver CPL, set the selector to and press and hold the button for 5 sec. The unit displays rAdio. On the receiver, press the test key (it emits a beep).

Beeep 1

To associate your Driver CPL to a TYXAL alarm central control unit, turn the selector to and press and hold the button for 5 sec. The unit displays rAdio Press the Test button of the control unit. Check that rAdio is no longer displayed on the screen The central control unit is associated with the Driver CPL.

- 14 -

- 15 -
Wireless option Associating a TYDOM 200 multifunction remote control
To associate your Driver CPL with a TYDOM 200 remote control On the Driver CPL, set the selector to and press and hold the button for 5 sec. The unit displays rAdio On TYDOM 200, - if the TYDOM 200 remote control screen is not displayed, press one of the domain butP , BEE tons, BEEP - press the home domain button until the remote control transmits one beep and the symbol flashes, - press on one of the tactile comfort or economy buttons of the TYDOM 200 remote control. On the Driver CPL, rAdio is no longer displayed. The and buttons of the TYDOM 200 remote control are associated with the Driver CPL.

To associate the

buttons of the TYDOM 200. and press and hold
On the Driver CPL, set the selector to the button for 5 sec. The unit reads rAdio. On the TYDOM 200, press on one of the tactile shutdown or automatic buttons on the remote control.
Associating shutdown and automatic modes
On the Driver CPL, rAdio is no longer displayed. The and buttons of the TYDOM 200 remote control are associated with the Driver CPL. To exit association mode, press another domain button (e.g. lighting ).

3 sec. Associating comfort and economy modes

, BEE BEEP

Lighting

- 16 -

- 17 -
Wireless option Associating a TYXIA remote control
To associate your Driver CPL with a TYXIA remote control. On the Driver CPL, set the selector to and press and hold the button for 5 sec.
Associating a TYDOM 300 telephone transmitter
To associate your Driver CPL with a TYDOM 300 telephone transmitter On the Driver CPL, set the selector to hold the button for 5 sec. The unit displays rAdio. On the TYDOM 300 (transmitter), press the button on the top of the unit. The transmitter emits 3 confirmation beeps. Check that rAdio is no longer displayed on the screen. The TYDOM 300 transmitter is associated with the DRIVER CPL. and press and
The unit displays rAdio. On the transmitter, press and hold down the and buttons together for about 5 seconds. The buttons will light up, go out, then light up again. Release.
On the Driver CPL, rAdio is no longer displayed. The emitters and buttons are associated with the Driver CPL. They allow for a Comfort or Economy override.
Deleting all the wireless product associations with the Driver CPL
On the DRIVER CPL, set the selector to and hold the button down for 10 sec., until the time is displayed (the DRIVER CPL displays rAdio after the button is held down for 5 sec.). All wireless product associations are deleted.

- 18 -

- 19 -

User guide

DRIVER 230 CPL
3 zone weekly programmer using power line carriers
DELTA DORE - Bonnemain 35270 COMBOURG - FRANCE E-mail : deltadore@deltadore.com
Device complying with the requirements of the directives: 2004/108/EEC (electromagnetic compatibility) and 2006/95/EEC (low voltage safety).

*2702030_rev1*

Contents
Description. 3 Time Setting. 5 The Pilot Wire. 5 Comfort, Economy, Frost Protection. 6 Automatic mode. 6 Change the programming. 7 Comfort or Economy Override. 8 Shutdown mode. 8 Adjustable frost protection. 9 Remote controlled absence mode.10 Domotic functions (if radio option)
with a door/window magnetic contact. 11 with a TYXIA Transmitter.. 11 with a TYDOM 200 remote control.. 12 with a TYDOM 300 telephone transmitter. 13 with a TYXAL alarm control unit.. 13-14

Description

Automatic mode Comfort
Economy Frost Protection Shutdown Programming Starting up
2 Current day 3 Tariff reduction in progress 4 Current mode:

Comfort Economy

5 Modification or override buttons 6 Timed absence button or validation

in programming mode

7 Knob selection mark 8 Identification of the heating zone
Because of changes in standards and equipment, the characteristics given in the text and the illustrations of this document are not binding unless confirmed by Delta Dore.

Heating Programming

- 1 customizable program per day and per zone - Automatic mode override: It is possible to use a different operating mode (Comfort, Economy, etc.) from the current one, until the next change of program - Absence: Constant or timed (from 1 to 99 days) to set the installation to frost protection mode

Time Setting

Turn the selector to
Press and release: slow forward. Press and hold: fast forward.
Each time you pass 0.00 you change the day
Transmission by power line carrier
- No damage to the existing installation - Use with pilot wire receivers of the X2D PLC range - Compatible with an energy manager (e.g. GECPL1, GP4 CPL) - Upgradeable system

The Pilot Wire

The pilot wire principle enables the required operating mode for the heating element to be selected from the programming control unit. The corresponding temperature is set directly by the heating element thermostat (room by room control).

Tariff Management

- Linked with a CPL X2D energy manager (e.g. GECPL1 or GP4 CPL), it can reduce your energy consumption according to the current tariff period - Compatibility with all tariffs
Command sent by the control unit Comfort Economy Frost Protection Shutdown
Corresponding temperature on the heating element
Comfort setting (thermostat knob) Economy setting or -2C or -3C in relation to the comfort setting (according to the model) Frost protection set to 7C or 8C (depending on model) Heating shutdown

Radio Option

- DRIVER CPL is compatible with the TYDOM 520 radio module that is used to associate domotics functions: door/window magnetic contact, alarm control unit, etc.
Comfort, Economy or Continuous Frost Protection

Permanent comfort

Z1 Z2 Z3

Change the programming

Turn the selector to PROG Z1. The 1st time slot flashes on and off.

Continuous Economy mode

The programming uses slots of one hour. Press the buttons + (comfort) or - (economy) to set each time slot.

E.g. Comfort from 6.00 am to 9.00 am from 12am to 2pm, from 6pm to 11pm.
Comfort for 1 hour Economy for 1 hour
Continuous Frost Protection
Confirm and go to the next day. Repeat for each day.

Automatic Mode

Turn the selector to AUTO

A U T O

Holding down the OK button lets you allocate the same program as the previously programmed day to the following day. To modify the program of zones 2 or 3 , turn the knob to PROG Z2 or PROG Z3 and repeat the steps above.
Change the position selector to exit the mode.
The unit follows the program for the three zones.
Override with automatic return (comfort or economy mode)
The selector is set to AUTO The unit follows the program (e.g. comfort in zone 1 and economy in zone 2 and 3)
Adjustable frost protection (1 to 99 days) - Absence mode
From the AUTO mode. Press for approximately 3 seconds until the suitcase symbol displays (continuous absence). Set the number of days of absence with the + or - buttons, the suitcase symbol flashes. The countdown begins. Example: leaving on 10 January, returning on 19 January, indicate 9 days. Automatic operation will resume on 19 January at 0:00 a.m.
Press. On zone 1, the unit operates in Economy mode until the next program change.
For a zone 2 or 3 override, press or. Note: If you are using 6-order pilot wire, override takes place amongst 4 modes: Comfort Economy Comfort -2C Comfort -1C

Heating shutdown

Remote controlled absence mode (Frost Protection)
DRIVER 230 CPL can be associated with a power line carrier telephone remote control (e.g. TYPHONE 2 CPL) or a GECPL1 whose telephone remote control input is connected to a TYPHONE 2 to enable remote selection between the absence mode and automatic operation.

Domotic functions

With the TYDOM 520 radio option, up to 16 domotics products can be associated (door/window magnetic contacts, telephone transmitter, alarm control unit, remote controls, etc.) using the DRIVER CPL.
- TYPHONE 2 + GECPL1 : Setting the absence mode Before leaving the dwelling, confirm your absence on the telephone remote control. "tELE" is displayed. Return to normal operation Order the termination of absence mode either remotely or locally (on the telephone remote control). The operation reverts to the one shown by the knob position. - TYPHONE 2 CPL: Setting the absence mode Remotely, send the absence command. The screen of the DRIVER CPL displays the suitcase and telephone symbols.

Return to normal operation Remotely: stop the absence order. Locally: change the knob position, then return it to the required position.
Operation with a door/window magnetic contact
You can combine up to 16 door/window magnetic contacts (maximum number of domotics products that can be combined). If one of them is opened, DRIVER CPL sets the installation to Frost Protection mode.
Operation with a TYXIA Transmitter
For this type of operation, the DRIVER CPL must be in automatic mode. Pressing the button enables a comfort override with automatic return at the next change of program. Pressing the button enables an economy override with automatic return at the next change of program. The override can be cancelled by pressing a button or turning the selector of the DRIVER CPL.

- 12 -

- 13 -
Domotic functions Operation with a Tydom 200 remote control
From the home domain : You can shut down the installation by pressing the tactile button.
Operation with a TYDOM 300 telephone transmitter
By calling the TYDOM 300 telephone transmitter, let the synthetic voice guide you to determine or modify the status of the heating system (see the TYDOM 300 transmitter guide). If a change is made via the TYDOM 300 telephone transmitter, the DRIVER CPL displays the telephone symbol and the mode controlled (e.g. comfort). Change the position of the DRIVER CPL to return to normal operation.
This shutdown command is cancelled:
- either by pressing the button , - or by changing the position of the DRIVER CPL selector. In the AUTO position of the DRIVER CPL only: Pressing the tactile button or once enables an override operation
Operation with a TYXAL alarm control unit
The DRIVER CPL receives and displays the technical fault information of the TYXAL alarm control unit. If a fault occurs, the display flashes alternately with the current program for 2 minutes and indicates: 1. Intruder or technical alarm 2. Tamper alarm 3. Battery 4. Supervision 5. Open entry 6. Mains fault in progress 7. Technical fault in progress
The override is cancelled: By zone: - the next time the program switches over in the zone, - by pressing the , or button of the DRIVER CPL.

On the 3 zones: - by changing the position of the DRIVER CPL selector. - by pressing the , or button of the TYDOM 200.
Override according to the alarm status
In the AUTO position only and if the function(1) is activated: - Starting up the control unit fully sets the installation to Economy mode in the 3 zones (up to the next change of program). - Shutting down the control unit sets the installation to Comfort mode in the 3 zones (up to the next change of program).

Maintenance

Diagnosis/Solutions
Nothing is displayed on the room unit screen. You have just switched the unit on. You have just switched the unit on. There is no power supply Check your circuit breaker. An economy period interrupts automatic operation. The reduced tariff operating mode can be modified ( Price Programming). Overrides are permitted. You have 4 order pilot wire heating or it has been defined as such (see installation guide Allocation of receivers). Communication fault with the GECPL1 or GPCPL. Check the power supply of the GECPL1 or GP4 CPL or reconfigure your units. Communication fault with electronic meter. Check the connection between the electronic meter and the energy manager or contact your installer. Communication fault with the TYPHONE 2 CPL. Check the power supply of the TYPHONE 2 CPL or reconfigure your units (see installation guide, Allocation of receivers).

The symbol

is displayed.
The override is cancelled: By zone: - the next time the program switches over in the zone, - by pressing the , button of the DRIVER CPL. or On the 3 zones: - by changing the position of the DRIVER CPL selector.
You cannot access the Comfort. -1C and Comfort -2C operating modes. The equipment displays:
The override function is enabled by default depending on the status of the alarm, it can be deactivated during the radio configuration: From the radio screen, press the buttons to display ON or OFF. Release. Press or ON or OFF. to select

together

The equipment displays:
After 2 seconds without pressing, the screen of the DRIVER CPL returns to the radio display, press the DRIVER CPL button until the time displays.

- 14 -

- 15 -