RF 660

Wireless receiver
Installation and User Guide

Warnings

Carefully read these instructions prior to installation. The unit must be installed in compliance with currently applicable standards. Always switch off the mains before installing or servicing the unit. Do not attempt to repair the unit yourself; an after-sales service is available. The diagrams provided are simplified for greater clarity. The protective devices and other accessories required by the standards are not illustrated. Standard UTE NF C15-100 and good practice must be complied with. Connected or nearby equipment must not generate excessive interference (directive 2004/108/EEC).

Presentation

Associated with a programmer (e.g. RADIO DRIVER), the RF660 wireless receiver makes it easy for you to control your heat emitters (convectors, panel heaters, electric underfloor or ceiling heating, towel rail, storage heaters, etc.) by using the principle of the Pilot Wire. Antenna LEDs IMPORTANT: the heat emitter must be in automatic mode (PROG, AUTO, etc. depending on model) to receive orders from the programmer. Button
Pilot Wire order (mode) Setting on the heat emitter
Comfort setting (thermostat knob) example: 19C Comfort setting -1C (depending on model) Comfort setting -2C (depending on model) Economy setting (thermostat knob) example: 16C Comfort XC (depending on heat emitter model) Frost protection set to 7C or 8C (depending on model) Heating shutdown
RF 660 Wireless receiver/6-order pilot wire
IIndependent from the power supply of the heat emitter, the Pilot Wire is used to send the Comfort Economy , Frost Protection or Shutdown orders requested by the programmer. The required temperature is set on the thermostat of each heat emitter.

Room temperature

19C 18C 17C

Pilot Wire principle:

Programmer Heat emitters

Comfort Mdio Modrato

Pilot Wire orders

Economy

Absence
Receiver Pilot Wire (e.g. Wireless/Pilot Wire)

7C or 8C No Heating

*2701878_Rev.2*

Connection

Mounting and connections
Switch off the mains power supply to your electrical meter (general circuit breaker) before any intervention. - Remove the convector to obtain a clear access. - Fit the receiver behind the convector, letting the radio antenna project from it. - Connect the receiver then fit back the convector. Important: the operating temperature of the receiver must not exceed 50C. You must not install the receiver to near the hottest parts of the convector.

Pilot wire

Blue Brown Black brown wire black wire
DELTA DORE Bonnemain - 35270 COMBOURG - France E-mail : deltadore@deltadore.com

blue wire

Position behind the convector You must let the radio antenna project from the top of the convector to obtain a correct radio transmission.
Antenna radio Convector No
Screw-mounting Mounted on a wall using the screws and pegs supplied.
Device complying with the requirements of the directives: R&TTE 1999/5/CE
Because of changes in standards and equipment, the characteristics given in the text and the illustrations in this document are not binding unless confirmed by Delta Dore.
Mounting by double-sided adhesive tape Secure to the wall by using the double-sided adhesive tape supplied. Ensure that the surface on which the tape is applied is thoroughly clean before attaching the tape.
Association Associating the receiver with a transmitter
On the receiver: Press the button for about 3 seconds until the two LEDs flash: the receiver is in association mode. On the transmitter: Depending on the transmitter, go to radio configuration mode. Send the association radio information. (see the transmitter guide). On the receiver: The two LEDs stop flashing to confirm the association operation.
Home automation functions
The product is compatible with the following X2D transmitters: - door/window magnetic contacts (heating goes to frost protection mode when a window is opened), - telephone transmitters (remote control of the heating), - on/off, raise/lower and scenario home automation remote controls (in automatic mode: the product sets up a local override in Comfort or in Economy mode), - wireless alarm control units (in automatic mode: switch to economy mode when the alarm is activated and return to comfort mode when the alarm is deactivated). To associate the transmitters, refer to the Association section.

Operation

The LEDs show you the current mode: or.

Removing all the receiver associations
Press and hold the button. LED. The and LEDs flash after 3 seconds. Hold down the button. The LEDs are deactivated after 10 seconds. Hold down the button. The LED flashes after 30 seconds; all the associations are removed. Release the button.
The mdio (Comfort -1C) and modrato (Comfort -2C) modes are displayed by the
The LEDS are off for the Frost Protection and Off modes. The heat emitter must be in the automatic setting for the programmer to be able to control it.

Override

You can locally interrupt the current mode up to the next change of order sent by the control unit. Pressing the button carries out the override. The change is shown as follows: - the LED flashes during an override of the Comfort mode to the Eco mode, - the LED flashes during an override of the Eco mode to the Comfort mode.
Note: the association remains in the event of a power failure.
Important: an override is cancelled if there is a power failure.

Turning off the LEDs

You can keep the LEDs turned off permanently so that they do not annoy you during the night: - press and hold the receiver button for about 10 seconds, - all the LEDs switch off while letting the product function normally. To turn on the LEDs: - press and hold the receiver button for about 10 seconds, - the LEDs switch on according to the current operating mode.
Technical characteristics
230 V, 50 Hz power supply, +/-10% Class II insulation Power consumption: 0.5 VA Pilot wire output 0.1 A, 230 V, Radio frequency 868 MHz (standard EN 300 220) Radio range 100 to 300 metres outside, variable depending on the associated equipment (the range can be altered depending on the installation conditions and the electromagnetic environment) Number of transmitters that may be associated with the receiver: 8 max. Operating temperature: -5C to +50C Storage temperature: -10 to +70C Dimensions: 102 x 54 x 20 mm, Protection index: IP44 - IK 04 Install in an environment with normal pollution levels

Troubleshooting

You cannot associate a transmitter with your receiver. The maximum number of transmitters to associate with a receiver function is 8. Reset the unit to associate the transmitters again (see the "Association" section). The receiver does not recognise the command from a transmitter. The transmitter is not associated with the receiver. The receiver is still in association mode. The transmitter batteries are low. The receiver is too far from the transmitter. The temperature of a room does not reach the mode chosen by the programmer. The convector is not in the correct position. Check that the convector is set to the AUTOMATIC position. The power of the convector is insufficient. Replace the convector with a more powerful model. You have subscribed to the tempo tariff and you are in an economy period. You want to associate the receiver again. You must start by removing all the radio associations.

SMART COMFORT & EASY EFFICIENCY HEATING CONTROLS

About Delta Dore

Since 1970, Delta Dore manufactures heating controls for both water based heating and electric heating. Room thermostats, programmable thermostats, controllers, energy-consumption meters.a wide range of solutions to improve comfort at home and make savings on the energy bill. The company designs controls for traditional heating systems like boilers, electric heaters as well as for modern renewable energy based heating systems like heat pumps Thanks to its expertise with hard-wired and wireless communications, Delta Dore provides the end users with adjustable features like control, programming, measure, remote control as well as scalable features in home automation applications for lighting control, opening detection The company has a manufacturing facility of square metres in France and ofces in Germany, Poland and Spain. Delta Dore supplies plumbers merchants, electrical wholesalers and cooperates with the main European HVAC manufacturers.
Solutions perfectly suited for boilers, heat pumps and much more
With energy prices and domestic consumption ever on the rise, Delta Dore has strengthened its expertise to offer the end user: - Maximum comfort with a wide range of heating control and programming products - Solutions to reduce the energy usage and then to take part to the CO2 emission reduction effort.
Whats different about DELTA DORE?
A historical business in manufacturing electronic devices for heating systems An innovative design to offer products: - easy to install and set - easy to understand and use Products that meet the requirements of new and existing Energy savings in figures dwellings thanks to hard-wired and wireless versions A strong expertise in RF technology and a communication One extra degree could increase the heating bill by 7%. protocol X2D dedicated to home automation applications The right programming solution could generate to ensure: signicant savings on the energy bill: - the reliability of wireless solutions - up to 25% saving when used on boilers - the interoperability of heating control solutions - up to 7% saving when used on heat pumps. with further home automation applications.

CONTENTS

MONEY SAVINGS PRODUCTS FULLY UPGRADABLE APPLICATIONS
for boilers > Room thermostat > Programmable thermostat for boilers or heat pumps > 2-zone outdoor temperature compensated controller > Up to 6 zones controller for underoor heating for heat pumps as boiler back-up > 2-zone outdoor temperature controller > 2-zone controller for heat pumps > Programmable thermostat for solar panels > Solar panel heated-DHW control
ADD-ON SOLUTIONS FEATURES
Money savings Lexpertise thermique au service de votre projet
Chrono-proportional (P.I.) control
BENEFIT: Increase the energy efciency of heating systems by up to 10% Each and every Delta Dore thermostat controls the heating according to the chrono-proportional control method. The chrono-proportional control regularly calculates the duration of the ON and OFF periods in proportion to the difference between the measured and set-point temperatures. This ensures that the required temperature is reached quickly and accurately, without any sudden variations.

Programming

BENEFIT: Increase the energy efciency of heating systems by up to 12% Tailored to the lifestyle of the occupants, the programming function automatically lowers the set-point temperature of one or more zones in the dwelling during sleep and away periods each day of the week. Combined with a control function, the programming helps to reduce the total heating consumption.
Our combined control and programming products deliver thermal comfort all year round. And because everything is automated, you no longer have to worry about getting too hot or too cold.
Products fully upgradable
Delta Dore offers a whole range of complementary solutions so that more savings can be made.

Consumption metering

BENEFIT: Understand energy consumption to start saving View detailed consumption data with our consumption meters and get electricity usage measurements broken down by type (heating, etc.).
Wireless magnetic contact combined with heating control
BENEFIT: Automatically switch the heating off when the window is open Combine a door/window magnetic contact with a wireless heating control. Heating switches automatically to frost protection mode when the window is opened. It turns back to comfort mode when the window is closed.

Telephone remote control

BENEFIT: Manage your heat consumption any time, anywhere Use a telephone remote control to manage heating applications. The perfect solution for secondary homes.
La Boiler application pour pompe chaleur rversible gestion dnergie Solutions > Programmation et rgulation sur temprature intrieure Solution > Room thermostat

Operating principle

The thermostat controls the temperature of the home according to the temperature of the room. It can be connected to the oil/gas boiler thermostat input to the circulator pump.

Benefits

7% energy saving on the heating bill when using a room thermostat Easy to use High precision control as the temperature sensor can be calibrated to user-specic requirements
The solution includes: Hard-wired version - D10: one room unit Wireless version - Radio D10: one room unit and one wireless receiver

D10/Radio D10 functions

Chrono-proportional (PI) control Indication of room temperature 3 adjustable temperature settings: Comfort Setback Frost Protection Shutdown position Settings can be locked The wireless version solution is perfect for existing installations - Quick to install. Blends in with the home interior. No unsightly cables between the thermostat and receiver (located near the boiler) - Radio range of 100 to 300 metres / 109 yd to 128 yd

Room Thermostat D10

Boiler

Receiver

Wireless room Thermostat Radio D10

Products

Reference no.

6050486

Add-on solutions

RADIO D10

6050487
Radio MINI COX magnetic contact - ref. 6412254 Telephone remote control TYPHONE 5 SV - ref. 6201048
For more information about add-on solutions, refer to p.14-15
Boiler application Solution > Programmable thermostat
The programmable thermostat controls the temperature of the home according to the temperature of the room. The programming function allows the temperature of the specic zone to be reduced according to occupants requirements to deliver maximum comfort and energy savings. It can be connected to the oil/gas boiler thermostat input to hot water circuit(s) circulator pump(s).

The solution includes: Hard-wired version - TYBOX 710/711/713/714: one room unit Wireless version - Radio TYBOX 810/811: one room unit and one wireless receiver Wireless version - Radio TYBOX 820/821: two room units and one wireless receiver
10-25% saving on the heating bill thanks to the association of control and programming functions Elegant design Large easy-to-read screen Easy to use: the knob provides quick access to all thermostat functions High precision control as the temperature sensor can be calibrated to user-specic requirements
Programmable thermostat TYBOX 713 Boiler
TYBOX and Radio TYBOX functions
Daily or weekly programming by zone Programming by step of quarter hour, half hour or hour Chrono-proportional (PI) control An absence of 1 to 365 days can be programmed Programs and settings can be locked The wireless version solution is perfect for existing installations - Quick to install. Blends in with the home interior. No unsightly cables between the thermostat and receiver (located near the boiler) - Radio range of 100 to 300 metres / 109 yd to 128 yd

Receiver Radio TYBOX 821

Programmable thermostat Radio TYBOX 821

Zone 2

Zone 1
TYBOX 710 - Batteries operated - 1 zone TYBOX 711- 230 V - 1 zone TYBOX 713 - Backlit - Batteries operated - 1 zone TYBOX 714 - Backlit - 230 V - 1 zone Radio TYBOX 810 - 1 zone Radio TYBOX 820 - 2 zones Radio TYBOX 811 - Backlit - 1 zone Radio TYBOX 821 - Backlit - 2 zones

6050503 6050505

Boiler or heat pump application Solution > 2-zone outdoor temperature compensated controller
The DELTA 200 controller manages the heating in the home according to the outdoor temperature and to the underoor system feed temperature. It controls the opening and closing of the underoor heating mixing valve and activates/deactivates 2 circulator pumps to control the temperature of 2 heating zones in the home. The controller optimises heating within these zones based on the outdoor temperature measured by the sensor. It calculates the exact time required to reach the desired temperature by the scheduled time, regardless of weather conditions outside. The programming function allows the temperature of the specied zones to be reduced according to occupants requirements to deliver maximum comfort and energy savings.
The DELTA 200 solution includes: A ush-mounted room unit, a technical unit, an outdoor temperature sensor, an underoor system feed temperature sensor and a return temperature sensor for the 2nd zone.

Optimises temperature rises according to the weather conditions for a more energy efcient home Savings on the heating bill thanks to the association of control and programming functions: - 10-25% saving when used on a boiler - 7-10% saving when used on a heat pump Easy to use
Possible application for one hot water radiant oor zone and one radiator zone, or two radiator zones.

Delta 200

DELTA 200

DELTA 200 functions

Daily or weekly programming by zone Programming by step of hour An absence of 1 to 99 days can be programmed Program settings can be locked Adjustment of minimum and maximum water temperatures on both networks Temperature control based on the heating curve
Outdoor temperature sensor

Sensor Sensor

Product

6000022

Consumption meters TYWATT 30 - ref. 6110021 TYWATT TRI - ref. 6110023
Boiler or heat pump application Solution > Up to 6 zones controller for underfloor heating
The DELTA 600 controller manages heating room by room according to the temperature of each room. It controls the buildings hot water underoor heating via 6 thermal actuator controls. Each DELTA 600 TH thermostat controls the thermal actuator for the oor assigned to it. DELTA 600 TH programmable room thermostats can be used to change the set-point temperature of each of the zones at any time. Heating is controlled centrally via DELTA 600 COM, allowing the user to switch all the zones to economy mode, for example, from a single point before leaving the house.
Separately controls the temperature of up to 6 underoor heating zones Savings on the heating bill thanks to the association of control and programming functions: - 10-25% saving when used on a boiler - 7-10% saving when used on a heat pump Easy to use
The DELTA 600 solution includes: A DELTA 600 BT technical unit, a DELTA 600 TH programmable room thermostat for each target zone, and a DELTA 600 COM for a central control function.
Technical unit DELTA 600 BT

DELTA 600 functions

Separate weekly programming for each of the rooms or zones Programming by step of hour General control function to centralise all the zones In-built safety function to provide circuit overpressure protection
DELTA 600 com Centralised control

DELTA 600 TH

Zone 6

Zone 5

Zone 4 Boiler Zone 3 Zone 2
DELTA 600 BT DELTA 600 TH DELTA 600 COM

6000025

LaHeat pump as boiler back-up application non rversible gestion dnergie pour pompe chaleur Solutions > > 2-zone outdoor temperature compensated controller Solution Programmation et rgulation sur temprature intrieure
The T1C-2 DIGIT electronic modular thermostat automatically selects the heat pump or the boiler as the energy source according to the outdoor temperature. Heating in the home is regulated according to the outdoor temperature and to the underoor system feed temperature. The DELTA 200 controls the opening and closing of the underoor heating mixing valve and activates/deactivates 2 circulator pumps to control the temperature of 2 heating zones in the home.

The selection of the energy source (heat pump or boiler) is managed automatically according to the outdoor temperature in order to optimise energy consumption Optimises temperature rises according to the weather conditions for a more energy efcient home Energy savings on the heating bill thanks to the association of control and programming functions: - 10-25% saving for boiler operation - 7-25% saving for heat pump operation Easy to use
The solution includes: One technical unit (T1C-2 DIGIT), a ush-mounted room unit, a technical unit, an outdoor temperature sensor, an underoor system feed temperature sensor and a return temperature sensor for the 2nd zone (DELTA 200).
Possible application for one hot water radiant oor zone and one radiator zone or two radiator zones.

Technical unit DELTA 200

T1C-2 digit

Functions T1C-2 DIGIT

Selects the energy source to be used Sets the minimum set-point temperature to ensure optimum heat pump operation
Outdoor temperature sensor Mixing tank
Daily or weekly programming by zone Programming by step of an hour An absence of 1 to 99 days can be programmed Program settings can be locked Adjustment of minimum and maximum water temperatures on both networks Temperature control based on the heating curve

Heat pump

Zone 1 Boiler

T1C-2 DIGIT

6150031
Outdoor sensor - ref. 6300001 Consumption meters TYWATT 30 - ref. 6110021 TYWATT TRI - ref. 6110023
Heat pump as boiler back-up application Solution > 2-zone controller
The T1C-2 DIGIT electronic modular thermostat automatically selects the heat pump or the boiler as the energy source according to the outdoor temperature. Heating in the home is regulated according to the temperature of the room. The programmable thermostats Radio TYBOX control 2 heating zones according to the temperature of each zone by activating/deactivating the circulator pumps.
The solution includes: One technical unit (T1C-2 DIGIT), two wireless room units and one 2-channel wireless receiver (Radio TYBOX 821).

The selection of the energy source (heat pump or boiler) is managed automatically according to the outdoor temperature to optimise energy consumption Energy savings on the heating bill thanks to the association of control and programming functions: - 10-25% saving for boiler operation - 7-10% saving for heat pump operation Easy to use: the programmable thermostat knob provides quick access to all thermostat functions High precision control as the indoor temperature sensor can be calibrated to user-specic requirements
Receiver Radio TYBOX 821 Programmable thermostat Radio TYBOX 821
Programmable thermostat Radio TYBOX 8 21

Radio TYBOX 820/821

Weekly programming by zone Chrono-proportional control Programming by step of quarter hour, half hour or hour An absence of 1 to 365 days can be programmed No unsightly cables between the thermostat and receiver (located near the boiler) Radio range of 100 to 300 metres / 109 yd to 128 yd Programs and settings can be locked

Mixing tank

Outdoor sensor - ref. 6300001 Consumption meters TYWATT 30 - ref. 6110021 TYWATT TRI - ref. 6110023 Radio MINI COX magnetic contact - ref. 6412254 Telephone remote control TYPHONE 5 SV - ref. 6201048
Radio TYBOX 820 Radio TYBOX 821 - Backlit

6050481 6050505

Heat pump application Solution > Programmable thermostat
The programmable thermostat controls the temperature of the home in heating or cooling mode according to the temperature of the room (underoor heating/cooling). The programming function allows the temperature of the specied zone to be reduced according to occupants requirements to deliver maximum comfort and energy savings. The programmable thermostat can control a heat pump using one of 2 types of connection: - in summer/winter mode via the change-over function and the heat pumps thermostat input - via the 2 thermostat inputs (heat mode or cooling mode).
The solution includes: Hard-wired version - TYBOX 712/715: one room unit Wireless version - Radio TYBOX 812/813: one room unit and one wireless receiver
Elegant design Control a heat pump using heating or cooling mode 7-10% saving on the energy bill thanks to the association of control and programming function Easy to use: the knob provides quick access to all thermostat functions High precision control as the temperature sensor can be calibrated to user-specic requirements
Heat pump Receiver Radio TYBOX 813 TYBOX 715 Radio TYBOX 813
TYBOX 712 and Radio TYBOX 812 functions
Weekly programming by zone Chrono-proportional (PI) control Heat pump protection with time base that can be set from 30 to 60 minutes Programming by step of quarter hour,half hour or hour An absence of 1 to 365 days can be programmed Programs and settings can be locked The wireless version solution is perfect for existing installations - Quick to install. Blends in with the home interior. No unsightly cables between the thermostat and receiver (located near the boiler) - Radio range of 100 to 300 metres / 109 yd to 128 yd

TYBOX 712 TYBOX 715 - Backlit Radio TYBOX 812 Radio TYBOX 813 - Backlit

6050485 6050504

Solar panel application Solution > Solar panel heated-DHW control
The electronic modular thermostat controls the water temperature in the circuit. It controls the circulation of the heat transfer uid based on the difference in temperature between the water heater and the solar panel. For example: If the temperature of the solar panel goes 10C above that of the water heater, the thermostat activates the circulator so that the heat transfer uid can warm up the water heater. If the temperature of the solar panel goes down to 2C above that of the solar water heater, the thermostat stops the circulator.
The T1D DIGIT solution includes: One technical unit

T1D DIGIT functions

Frost protection function ensures circulation of heat transfer uid when the outdoor temperature falls below a set threshold Setting of two difference thresholds (large and small difference) Safety temperature setting (0 to 150 C) Display of the 3 measured temperatures 3 sensor inputs (solar panel, water heater and outdoor temperature)

The solar panel

Temperature sensor 1

T1D DIGIT Storage tank

DHW Sensor 2 Thermostatic mixing valve

Electric resistance

Solar cylinder

T1D DIGIT

References no.

6050032

Underfloor or piping sensor - ref. 6300002
ADD-ON SOLUTIONS ACCESSOIRES
Electricity consumption meters
Consumption meters measure electricity consumption for heating, domestic hot water, etc. and display usage in kWh. Benet: By providing a detailed view of consumption habits, these metres make users more aware of how resources are being used and how energy bills can be reduced.

TYWATT 30

Consumption meter for a single-phase installation Allows users to measure the kWh consumption of all or part of the electrical system (heating, domestic hot water, heat pump, etc.) Compatible with an electronic meter or an electromechanical meter Displays the total KWh consumption by rate period Double meter (one continuous and one that can be initialized) Displays the maximum average power reached

DELTA 600 BT Technical unit

FEATURES

Programmable thermostats for reversible and non-reversible heat pumps
Power supply: 2 x 1.5V AAA batteries (supplied) One 2 A contact output One 2 A change-over contact output Control range 5 to 30 C Control time base can be set at 30/45/60 minutes Dimensions: H 104 x L 80 x D 35 mm Transmitter power supply: 2 x 1.5V AAA batteries (supplied) Receiver power supply: 230 V/50 Hz Two 3 A configurable dry contact outputs Control range 5 to 30 C Control time base can be set at 30/45/60 minutes Radio frequency 868 MHz Transmitter dimensions: H 104 x L 80 x D 37 mm Receiver dimensions: H 120 x L 54 x D 25 mm

TYBOX 712/715

Radio TYBOX 812/813

Modular thermostats

Multi-application: control of the temperature and monitoring Power supply: 230 V/50 Hz 3 control range -10 to 90 C Accuracy temperature 0,2 to 2C One 5 A configurable dry contact output Dimensions: H 84 x L 53 x D 59 mm
Solar panel heated-DHW control Power supply: 230 V/50 Hz 3 control range -10 to 90 C One 5 A configurable dry contact output Accuracy temperature 0,2 to 2 C Dimensions: H 84 x L 53 x D 59 mm
Ducted air conditioning system Solution > Up to 6 zones controller
The radio DELTA 630 solution controls and programs the temperature of the home in heating or cooling mode according to the temperature of the room Each DELTA 630 TH room thermostat controls the motorised register of the zone or room assigned to it. It can be used to change the set-point temperature locally at any time. The DELTA 630 MASTER programmer manages the programming of each of the zones based on 2 temperature settings (Comfort or Setback)
The Radio Pack DELTA 630 solution includes : One technical unit (DELTA 630 BT), 4 wireless room thermostats to control the first 4 registers (DELTA 630 TH), one wireless programmer (DELTA 630 Master) and one limit sensor.
10-25% saving on the heating bill thanks to the association of control and programming functions Elegant design Large Easy-to-read screen Easy to use : the knob provides quick access to all thermostat functions

Functions

Controls up to 6 register-equipped zones by time and temperature Daily or weekly centralised programming by zone The wireless version solution is perfect for existing installations : - Quick to install. Blends in with the home interior. No unsightly cables between the thermostat and technical unit - Radio range of 100 to 300 metres 109 yd to 328 yd
Pack DELTA 630 - Backlit DELTA 630 TH - Backlit DELTA 630 MASTER - Backlit DELTA 630 BT

6050514 6050515

Features
DELTA 630 MASTER programmer Transmitter power supply: 2 x 1.5V AAA batteries (supplied) One Change-Over command Radio frequency 868 MHz Dimensions: H 104 x L 80 x D 35 mm DELTA 630 TH room thermostat Transmitter power supply: 2 x 1.5V AAA batteries (supplied) Radio frequency 868 MHz Dimensions: H 80 x L 80 x D 23 mm DELTA 630 BT technical unit Includes one change-over temperature sensor which checks the AC systems output temperature to activate or deactivate the fan whenever the mode changes (heating/cooling). Power supply 230 V Three (non-powered 5 A 230 V), NO contact outputs : changeover, interior unit One register power supply input Six 230V / 24 V DC / 12 V DC register contact outputs Dimensions: H 130 x L 180 x D 60 mm
Reversible AC split system application Solution > Interface for infrared control of reversible air conditioning systems
The Radio D30 is an infrared interface that controls reversible mode air conditioning systems. It can record up to 22 remote control screens for AC split systems. It gives access to three modes: heating / cooling and fan mode. And local overrides can be done: Comfort heating, Setback heating, comfort heating, fan speed.
The thermostat operates by copying the infrared signals of the original Ac split system remote controls and can then manage a maximum number of existing and further split AC systems without updating the product. Several Radio D30 may be associated to a wireless programmer to provide a programming function.
The solution includes : one room unit.

Radio D30

Power supply: 230V / 50Hz Radio frequency 868 MHz Wireless range 150 to 200 metres / 164 yd to 218 yd Dimensions: H 80 x L 80 x D 23 mm

AC split system

6203001
Electric heating application Solution > Programmers for electric heating systems with pilot wire
The DRIVER programmer controls electric heaters based on 2 temperature settings (Comfort, Setback). The Comfort temperature is set on the heater. The Setback temperature is 3.5 below the set Comfort temperature. The program is customised according to the occupants lifestyle. During the night or when occupants are out, the programmer will lower the heating in the house to reduce unnecessary energy consumption. Depending on the model, it can manage the programming of up to 3 separate zones. A choice of 3 technologies are available, depending on the installation: - Wireless/Pilot Wire, perfectly suited for existing dwellings - Powerline carrier/Pilot Wire, perfectly suited for existing dwellings - Pilot Wire, ideal for new dwellings

10-25% saving on the heating bill thanks to the programming function Easy to use : the knob provides quick access to all thermostat functions
Daily or weekly programming by zone Timer-controlled zone override function, from 15 min to 72 hours Permanent override function using the knob Absence of 1 to 365 days can be programmed
Wireless programmer: Radio DRIVER
Radio Driver Power supplied by 2 AAA batteries (supplied) 2-year battery life Radio frequency 868 MHz Wireless range 150 to 200 metres / 164 yd to 218 yd Dimensions: H 104 x L 80 x D 35 mm RF 660 FP wireless receiver 6-order pilot wire outputs Set-point level display Dimensions: H 102.5 x L 54 x D 19 mm (Antenna excl.)
PLC programmer : DRIVER CPL
PLC DRIVER 230 V power supply No filter at the head of the system Dimensions: H 128 x L 85 x D 31 mm TC 51089 receivers 6-order pilot wire outputs Set-point level display Dimensions: H 170 x L 50 x D 25 mm

Programmer : DRIVER

230 V power supply 6-order pilot wire outputs Dimensions: H 104 x L 80 x D 35 mm
Radio DRIVER 610 - 1 zone Radio DRIVER 620 - 2 zones Radio DRIVER zones RF 660 FP receivers PLC DRIVER 210 - 1 zone PLC DRIVER 220 - 2 zones PLC DRIVER 230 - 3 zones TC 51089 receivers DRIVER 610 - 1 zone DRIVER zones

6050506 6050507

Electric heating application Solution > Zone control by time and temperature
The programmable thermostat controls the temperature by controlling the electric heaters in one zone. It sends commands to the receivers through RF technology. The programming function allows to reduce the temperature of the room according to occupants requirements to deliver maximum comfort and energy savings.
The solution includes: One wireless room unit (Radio TYBOX) by zone and one wireless receiver (RF 642) for each electric heater.
10-25% saving on heating bill thanks to the association of control and programming functions Elegant design Large Easy-to-read screen Easy to use : the knob provides quick access to all thermostat functions High precision control as the temperature sensor can be calibrated to user-specific requirements
Programmable thermostat Radio TYBOX 801
Daily or weekly programming Programming by step of quarter hour, half hour or hour Chrono-proportional (PI) control An absence of 1 to 365 days can be programmed Programs and settings can be locked The wireless version solution is perfect for existing installations - Quick to install. Blends in with the home interior
. No unsightly cables between the thermostat programmable and receiver - Radio range of 100 to 300 metres 109 yd to 328 yd
Radio TYBOX 800 Radio TYBOX 801 - Backlit Receiver RF642

6351081

Room unit (transmitter only) Radio frequency 868 MHz Power supplied by 2 AAA batteries (supplied) Dimensions: H 104 x L 80 x D 35 mm RF 642 receivers: 16 A wireless receiver Radio frequency 868 MHz 16 A resistive contact output Dimensions: H 120 x L 54 x D 25

Electric heating application Solution > Up to 3 zones centralised control by time and temperature
The Radio DRIVER wireless programmer centrally programmes the electric heating by zone for up to 3 zones/rooms. Each Radio D10 wireless room thermostat controls the temperature of the corresponding room by sending information to the receivers associated with the electric heaters within the zone.
The solution includes: One wireless programmer room unit (Radio DRIVER), one wireless receiver (RF 642) for each electric heater, and one wireless room thermostat (Radio D10) for each zone
10-25% saving on the heating bill thanks to the association of control and programming functions Elegant design Large Easy-to-read screen Easy to use : the knob provides quick access to all thermostat functions Centralised programming for up to 3 zones

Radio Driver

Daily or weekly programming by zone Programming by step of quarter hour, half hour or hour Timer-controlled zone override function, from 15 min to 72 hours Permanent override function using the knob An absence of 1 to 365 days can be programmed Radio range of 150 to 200 metres / 164 yd to 218 yd
2-zone programmer Radio DRIVER 620
Chrono-proportional (PI) control 3 adjustable temperature settings: Comfort Setback - Frost Protection Shutdown position Settings can be locked The wireless solution is perfect for existing installations - Quick to install - Blends in with the home interior - No unsightly cables between the programmable thermostat and receiver - Radio range of 100 to 300 metres 109 yd to 328 yd
Radio DRIVER zones Radio DRIVER zones Radio DRIVER zones Radio D10 Receiver RF642
Radio Driver 630 / 620 / 610
Power supplied by 2 AAA batteries (supplied) 2-year battery life Radio frequency 868 MHz Dimensions: H 104 x L 80 x D 35 mm
Radio D10 Transmitter power supply : 2 x 1.5V AAA batteries (supplied) Receiver power supply: 230 V/50 Hz One 5 A/230 V dry contact Control range 5 to 30 C Radio frequency 868 MHz Transmitter dimensions: H 80 x L 80 x D 23 mm RF 642 receivers : 16 A wireless receiver Radio frequency 868 MHz 16 A resistive contact output Dimensions: H 120 x L 54 x D 25
Solid fuel boiler application: wood, wood pellets, coal Solution > Controller
The DELTA 40/42 RF controller controls the temperature of the heating water circuit. It activates/deactivates the circulator pump based on the temperature measured at the boiler's water outlet

When associated with a room thermostat, it also controls the heating based on the room temperature.
The solution includes : DELTA 40: One controller DELTA 42 RF: One controller and one wireless room thermostat
Allows the control of the heating circulator pump according to the temperature measured at the boiler water outlet. Controller shutdown and frost protection functions. The room temperature can be adjusted via a room thermostat placed in the room. It can be wired directly to a DELTA 40 controller or connected wirelessly to a DELTA 42 controller.
DELTA 42 RF controller + Wireless room thermostat Chrono-proportional (PI) control 3 adjustable temperature settings : Comfort Setback - Frost Protection Shutdown position Settings can be locked The wireless version solution is perfect for existing installations - Quick to install. Blends in with the home interior. No unsightly cables between the thermostat and the controller - Radio range of 100 to 300 metres 109 yd to 328 yd
DELTA 40 DELTA 42 RF With wireless room thermostat

6000026 6000028

Add-on solution
Hard-wired room thermostat

(supplied)

DELTA 40
230 V, 50 Hz power supply, pre-wired One 5 A 230 V relay output (heating circulator pump) One heating temperature sensor input (sensor supplied) One hard-wired thermostat input (thermostat not supplied) Dimensions : H 135 x L 143 x D 45 mm

DELTA 42

Wireless controller 230 V, 50 Hz power supply (pre-wired) One 5 A 230 V relay output (heating circulator pump) One heating sensor input (sensor supplied) Dimensions : H 135 x L 143 x D 45 mm Wireless room thermostat Power supply: 2 x 1.5 V AAA alkaline batteries (supplied) 2-year battery life Radio frequency 868 MHz
Solid fuel boiler with fan application: wood, wood pellets, coal Solution > Controller
The DELTA 41/43 RF controller controls the temperature of the heating water circuit and the domestic hot water. It activates/deactivates the circulator pumps based on the temperature measured at the boiler's water outlet It increases/decreases the air supply to the boiler by controlling the fan. When associated with a programmable thermostat, it also controls and programs the heating based on the room temperature.

The solution includes: DELTA 41: One controller DELTA 43 RF: One controller and one wireless programmable thermostat
The controller allows the control of the heating circulator pump according to the temperature measured at the boiler water outlet. It controls the circulator pump of the DHW. Controller shutdown and frost protection function. When associated with a programmable thermostat placed in the users chosen location, it adjusts and programs the room temperature.
DELTA 43 RF controller + Wireless programmable thermostat Daily or weekly programming by zone Programming by step of quarter hour, half hour or hour Chrono-proportional (PI) control Programs and settings can be locked The wireless version solution is perfect for existing installations : - Quick to install. Blends in with the home interior. No unsightly cables between the programmable thermostat and the controller - Radio range of 100 to 300 metres 109 yd to 328 yd

DELTA 41

6000027
. Hard-wired room thermostat. Hard-wired programmable thermostat

DELTA 43 RF

6000029
With wireless programmable thermostat (supplied)
230 V, 50 Hz power supply, pre-wired One 5 A 230 V relay outputs (heating circulator pump, DHW circulator pump, fan) Two sensor inputs: heating and DHW (heating sensor supplied) One hard-wired thermostat input (thermostat not supplied)) Dimensions : H 135 x L 143 x D 45 mm

DELTA 43

Wireless controller 230 V, 50 Hz power supply, pre-wired Three 5 A 230 V relay outputs (heating circulator pump, DHW circulator pump, fan) Two sensor inputs: heating and DHW (heating sensor supplied) Dimensions : H 135 x L 143 x D 45 mm Wireless programmable thermostat Power supply: 2 x 1.5 V AAA batteries (supplied) Battery life: 2 years Radio frequency 868 MHz
DELTA DORE Headquarter : Bonnemain - 35270 Combourg - France
COM3700367 - Alyza - Credits : Manuel Clauzier and MCP Promotion
mail export@deltadore.com