DENON AVR control protocol

Ver. 5.3.0.for 988

Application model : AVR-988 Application terminal: RS-232C

Connector specification

. RS-232C Connector type: DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC ) Communication format: Synchronous system : Tone step synchronization Communication system : A half duplex Communication speed : 9600bps Character length : 8 bits Parity control : None Start bit : 1 bit Stop bit : 1 bit Communication procedure : Non procedural Communication data length : 135 bytes (maximum)
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT. RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR) if the request command (COMMAND+?+CR(0x0D)) has came from a controller. The RESPONSE should be sent within 200ms of receiving the COMMAND. *The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification: The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs, AND carriage return (0x0D) --- It is used only as a pause sign.
Command structure: COMMAND + PARAMETER + CR (0x0D)
COMMAND: ASCII CODE of 2 characters Ex. SI : Select Input source MS : surround Mode Setting MV : Master Volume setting PW : system PoWer setting PARAMETER : ASCII CODE ( up to 25 characters) ex. DVD : function name SUPER STADIUM : surround mode name *Special Parameter--- ? : for request command

The example of a command

* <CR> is the meaning of 0x0D. SIDVD<CR> : Select Input source DVD MSSTEREO<CR> : surround Mode Set to STEREO MVUP<CR> : Master Volume UP PWON<CR> : system Power ON PWSTANDBY<CR> : system Power STANDBY SI?<CR> : Request command for now playing input source >> Return RESPONSE SI***<CR>

Others

A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50". D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel volume of all channels , It described in B) ) returns as EVENT. E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME does NOT return. F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return. G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned. H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to the another request commands(ex. SV command). I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines 99. J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three ASCII characters as bellows. Ex. MASTER VOLUME = +1.0dB : MV81<CR> +0.5dB : MV805<CR> 0dB : MV80<CR> -0.5dB : MV795<CR> -1.0dB : MV79<CR> | | -79.5dB : MV005<CR> -80.0dB : MV00<CR> --: MV99<CR> * At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual. K) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMANDPWON.

COMMAND SD

PARAMETER AUTO HDMI DIGITAL ANALOG EXT.IN-1 ? AUTO PCM DTS ? DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE ? DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND NEURAL WIDE SCREEN 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB
function set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical,Coaxial)mode set force ANALOG INPUT mode ---Set EXT.IN mode at AVR-2808 Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set , and select source
example SDAUTO<CR> SDHDMI<CR> SDDIGITAL<CR> SDANALOG<CR> SDEXT.IN-1<CR> SD?<CR> DCAUTO<CR> DCPCM<CR> DCDTS<CR> DC? SVDVD<CR> SVVDP<CR> SVTV/CBL<CR> SVSAT<CR> SVVCR<CR> SVDVR<CR> SVV.AUX<CR> SVSOURCE<CR> SV?<CR> MSDIRECT<CR> MSPURE DIRECT<CR> MSSTEREO<CR> MSSTANDARD<CR> MSDOLBY DIGITAL<CR> MSDTS SURROUND<CR> MSNEURAL<CR> MSWIDE SCREEN MS7CH STEREO<CR> MSSUPER STADIUM<CR> MSROCK ARENA<CR> MSJAZZ CLUB<CR>
VIDEO SELECT mode cancel Return SV Status Select SURROUND mode
(North America model Only)

COMMAND MS

PARAMETER CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL ? QUICK1 QUICK2 QUICK3 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK ? ASPNRM ASPFUL ASP? SC48P SC10I SC72P SC10P SC AUTO SC?

function

Return MS Status QUICK SELECT 1-3 MODE SELECT USER1-3 MODE MEMORY Return MSQUICK Status Set Normal mode Set FULL mode Return VSASPECT Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolution to 1080p Set Resolution to AUTO Return VSSCALE Status
example MSCLASSIC CONCERT<CR> MSMONO MOVIE<CR> MSMATRIX<CR> MSVIDEO GAME<CR> MSVIRTUAL<CR> MS?<CR> MSQUICK1<CR> MSQUICK2<CR> MSQUICK3<CR> MSQUICK1 MEMORY<CR> MSQUICK2 MEMORY<CR> MSQUICK3 MEMORY<CR> MSQUICK ?<CR> VSASPNRM<CR> VSASPFUL<CR> VSASP?<CR> VSSC48P<CR> VSSC10I<CR> VSSC72P<CR> VSSC10P<CR> VSSCAUTO<CR> VSSC?<CR>

COMMAND PS

PARAMETER TONE DEFEAT ON TONE DEFEAT OFF TONE DEFEAT ? SB:MTRX ON SB:NON MTRX SB:PL2xCINEMA SB:PL2xMUSIC SB:ON SB:OFF SB: ? CINEMA EQ.ON CINEMA EQ.OFF CINEMA EQ. ? MODE:MUSIC MODE:CINEMA MODE:GAME MODE:PRO LOGIC
function PARAMETER setting TONE DEFEAT ON/OFF Return PSTONE DEFEAT Status SURROUND BACK SP MODE set
Return PSSB: Status CINEMA EQ. ON/OFF Return PSCINEMA EQ.Status CINEMA / MUSIC / GAME / PL mode change (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) ---SB=ONPL2x mode / SB=OFFPL2 mode --- GAME can change DOLBY PL2 & PL2x mode --- PL can change ONLY DOLBY PL2 mode Return PSMODE: Status ROOM EQ mode direct change

example PSTONE DEFEAT ON<CR> PSTONE DEFEAT OFF<CR> PSTONE DEFEAT ?<CR> PSSB:MTRX ON<CR> PSSB:NON MTRX<CR> PSSB:PL2X CINEMA<CR> PSSB:PL2X MUSIC<CR> PSSB:ON<CR> PSSB:OFF<CR> PSSB: ?<CR> PSCINEMA EQ.ON<CR> PSCINEMA EQ.OFF<CR> PSCINEMA EQ. ?<CR> PSMODE:MUSIC<CR> PSMODE:CINEMA<CR> PSMODE:GAME<CR> PSMODE:PRO LOGIC<CR> PSMODE: ?<CR> PSROOM EQ:AUDYSSEY<CR> PSROOM EQ:BYP.LR<CR> PSROOM EQ:FLAT<CR> PSROOM EQ:MANUAL<CR> PSROOM EQ:OFF<CR> PSROOM EQ: ?<CR> PSBAS UP<CR> PSBAS DOWN<CR> PSBAS 50<CR> PSBAS ?<CR>
MODE: ? ROOM EQ:AUDYSSEY ROOM EQ:BYP.LR ROOM EQ:FLAT ROOM EQ:MANUAL ROOM EQ:OFF ROOM EQ ? BAS UP BAS DOWN BAS ** BAS ? PS COMMAND : "*" parameter
Return PSROOM EQ: Status BASS UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 50=0dB ---AVR-2808 can be operated from -6 to +6(44 to 56) Return PSBAS Status uses two ASCII characters. (see page4 J) section)
TRE TRE TRE TRE DRC DRC DRC DRC DRC DRC DCO DCO DCO DCO DCO LFE LFE LFE LFE EFF EFF EFF EFF DEL DEL DEL DEL AFD AFD AFD PS COMMAND
PARAMETER function example UP PSTRE UP<CR> TREBLE UP/DOWN , direct change to **dB DOWN PSTRE DOWN<CR> **:00 to 99 by ASCII , 50=0dB ** PSTRE 50<CR> ---AVR-2808 can be operated from -6 to +6(44 to 56) ? PSTRE ?<CR> Return PSTRE Status AUTO PSDRC AUTO<CR> DRC direct change LOW PSDRC LOW<CR> MID PSDRC MID<CR> HI PSDRC HI<CR> OFF PSDRC OFF<CR> ? PSDRC ?<CR> Return PSDRC Status OFF PSDCO OFF<CR> D.COMP direct change LOW PSDCO LOW<CR> MID PSDCO MID<CR> HIGH PSDCO HIGH<CR> ? PSDCO ?<CR> Return PSDCO Status UP PSLEE UP<CR> LFE UP/DOWN , direct change to **dB DOWN PSLFE DOWN<CR> **:00 to 99 by ASCII , 00=0dB, 10=-10dB ** PSLFE 10<CR> ---AVR-2808 can be operated from 0 to -10 ? PSLFE ? <CR> Return PSLFE Status ON PSEFF UP<CR> EFFECT ON/OFF , EFFECT LEVEL direct change to **dB OFF PSEFF DOWN<CR> **:00 to 99 by ASCII , 00=0dB, 10=10dB ** PSEFF **<CR> ---AVR-2808 can be operated from 1 to 15 ? PSEFF ?<CR> Return PSEFF Status UP PSDEL UP<CR> DELAY UP/DOWN , direct change to ***dB DOWN PSDEL DOWN<CR> ***:000 to 999 by ASCII , 000=0ms, 300=300ms *** PSDEL ***<CR> ---AVR-2808 can be operated from 0 to 300 ? PSDEL ?<CR> Return PSDEL Status ON PSAFD ON<CR> AFDM ON/OFF OFF PSAFD OFF<CR> ? PSAFD ?<CR> Return PSAFD Status : "*" parameter uses two or three ASCII characters. (see page4 J) section)

- 10 -

PARAMETER function example PAN ON PSPAN ON<CR> PANORAMA ON/OFF PAN OFF PSPAN OFF<CR> PAN ? PSPAN ?<CR> Return PSPAN Status DIM UP PSDIM UP<CR> DIMENSION UP/DOWN , direct change to **dB DIM DOWN PSDIM DOWN<CR> **:00 to 99 by ASCII , 00=0, DIM ** PSDIM **<CR> ---AVR-2808 can be operated from 0 to 6 DIM ? PSDIM ?<CR> Return PSDIM Status CEN UP PSCEN UP<CR> CENTER WIDTH UP/DOWN , direct change to **dB CEN DOWN PSCEN DOWN<CR> **:00 to 99 by ASCII , 00=0 CEN ** PSCEN 07<CR> ---AVR-2808 can be operated from 0 to 7 CEN ? PSCEN ?<CR> Return PSCEN Status CEI UP PSCEI UP<CR> CENTER IMAGE UP/DOWN , direct change to **dB CEI DOWN PSCEI DOWN<CR> **:00 to 99 by ASCII , 00=0.0 CEI ** PSCEI 10<CR> ---AVR-2808 can be operated from 0.0 to 1.0 CEI? OSCEI ?<CR> Return PSCEI Status ATT ON PSATT ON<CR> SW ATT ON/OFF ATT OFF PSATT OFF<CR> ATT ? PSATT ?<CR> Return PSATT Status SWR ON PSSWR ON<CR> SW ON/OFF SWR OFF PSSWR OFF<CR> SWR ? PSSWR ?<CR> Return PSSWR Status RSZ S PSRSZ S<CR> ROOM SIZE direct change RSZ MS PSRSZ MS<CR> RSZ M PSRSZ M<CR> RSZ ML PSRSZ ML<CR> RSZ L PSRSZ L<CR> RSZ ? PSRSZ ?<CR> Return PSRSZ Status DELAY UP PSDELAY UP<CR> AUDIO DELAY UP/DOWN , direct change to ***dB DELAY DOWN PSDELAY DOWN<CR> ***:000 to 999 by ASCII , 000=0ms, 200=200ms DELAY *** PSDELAY 200<CR> ---AVR-2808 can be operated from 0 to 200 PS COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

- 11 -

PARAMETER function NIGHT OFF NIGHT MODE direct change NIGHT LOW NIGHT MID NIGHT HI NIGHT ? Return PSNIGHT Status RSTR OFF AUDIO RESTORER direct change RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? Return PSRSTR Status PV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)
example PSNIGHT OFF<CR> PSNIGHT LOW<CR> PSNIGHT MID<CR> PSNIGHT HI<CR> PSNIGHT ?<CR> PSRSTR OFF<CR> PSRSTR MODE1<CR> PSRSTR MODE2<CR> PSRSTR MODE3<CR> PSRSTR ?<CR>

- 12 -

COMMAND Z2

Z2MU Z2CS Z2CV

PARAMETER PHONO | IPOD SOURCE UP DOWN ** ON OFF ? ON OFF ? ST MONO ? FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? ON OFF ?
function MULTI ZONE-2 mode set , and select source at AVR-2808 ---The name of PARAMETER is the same as that of the time of SI COMMAND. MULTI ZONE-2 mode cancel at AVR-2808 MULTI ZONE-2 VOLUME UP/DOWN , direct change to **dB at AVR-2808 **:10 to 99 by ASCII , 80=0dB, 99=---(MIN) MULTI ZONE-2 ON/OFF change at AVR-2808 Return Z2 Status ZONE2 OUTPUT MUTE ON/OFF change Return Z2MU Status ZONE2 Channel setting ---Invalid at AVR-988 Return Z2CS Status ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB ---FRONT Lch **:38 to 62 by ASCII , 50=0dB ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB ---FRONT Rch **:38 to 62 by ASCII , 50=0dB Return Z2CV Status ZONE2 HPF ON/OFF ---Invalid at AVR-988 Return Z2HPF Status

example Z2PHONO<CR> | Z2IPOD<CR> Z2SOURCE<CR> Z2UP<CR> Z2DOWN<CR> Z280<CR> Z2ON<CR> Z2OFF<CR> Z2?<CR> Z2MUON<CR> Z2MUOFF<CR> Z2MU?<CR> Z2CSST Z2CSMONO Z2CS? Z2CVFL UP<CR> Z2CVFL DOWN<CR> Z2CVFL 50<CR> Z2CVFR UP<CR> Z2CVFR DOWN<CR> Z2CVFR 50<CR> Z2CV?<CR> Z2HPFON<CR> Z2HPFOFF<CR> Z2HPF?<CR>
Z2 COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) Z2 COMMAND Invalid at AVC-2808 for JAPAN

- 13 -

COMMAND Z2PS
PARAMETER BAS UP BAS DOWN BAS ** BAS TRE TRE TRE ? UP DOWN **
function ZONE2 BASS UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB ---AVR-2808 can be operated from -10 to +10(40 to 60) ---Invalid at AVR988 Return Z2PSBAS Status ZONE2 TREBLE UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB ---AVR-2808 can be operated from -10 to +10(40 to 60) ---Invalid at AVR988 Return Z2PSTRE Status
example Z2PSBAS UP<CR> Z2PSBAS DOWN<CR> Z2PSBAS 00<CR> Z2PSBAS Z2PSTRE Z2PSTRE Z2PSTRE ?<CR> UP<CR> DOWN<CR> 00<CR>

Z2PSTRE ?<CR>

- 14 -

COMMAND Z3

PARAMETER function PHONO MULTI ZONE-3 mode set , and select source at AVR-2808 | ---The name of PARAMETER is IPOD the same as that of the time of SI COMMAND. SOURCE MULTI ZONE-3 mode cancel UP MULTI ZONE-3 VOLUME UP/DOWN , direct change to **dB DOWN ** **:10 to 99 by ASCII , 80=0dB, 99=---(MIN) ON MULTI ZONE-3 ON/OFF change at AVR-2808 OFF ? Return Z3 Status ON Z3MU ZONE3 OUTPUT MUTE ON/OFF change OFF ? Return Z3MU Status ST Z3CS ZONE3 Channel setting MONO ? Return Z3CS Status FL UP Z3CV ZONE3 CHANNEL VOLUME UP/DOWN , direct change to **dB FL DOWN ---FRONT Lch FL ** **:38 to 62 by ASCII , 50=0dB FR UP ZONE3 CHANNEL VOLUME UP/DOWN , direct change to **dB FR DOWN ---FRONT Rch FR ** **:38 to 62 by ASCII , 50=0dB ? Return Z2CV Status ON Z3HPF ZONE3 HPF ON/OFF OFF ? Return Z3HPF Status Z3 COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) Z3 COMMAND Invalid at AVR-988 and AVC-2808 for JAPAN
example Z3PHONO<CR> | Z3IPOD<CR> Z3SOURCE<CR> Z3UP<CR> Z3DOWN<CR> Z380<CR> Z3ON<CR> Z3OFF<CR> Z2?<CR> Z3MUON<CR> Z3MUOFF<CR> Z3MU?<CR> Z3CSST Z3CSMONO Z3CS? Z3CVFL UP<CR> Z3CVFL DOWN<CR> Z3CVFL 50<CR> Z3CVFR UP<CR> Z3CVFR DOWN<CR> Z3CVFR 50<CR> Z3CV?<CR> Z3HPFON<CR> Z3HPFOFF<CR> Z3HPF?<CR>

- 15 -

COMMAND Z3PS
BAS BAS BAS BAS TRE TRE TRE TRE
PARAMETER UP DOWN ** ? UP DOWN ** ?
function ZONE3 BASS UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB ---AVR-2808 can be operated from -10 to +10(40 to 60) Return Z3PSBAS Status ZONE3 TREBLE UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB ---AVR-2808 can be operated from -10 to +10(40 to 60) Return Z3PSTRE Status
Z3PSBAS Z3PSBAS Z3PSBAS Z3PSBAS Z3PSTRE Z3PSTRE Z3PSTRE Z3PSTRE
example UP<CR> DOWN<CR> 00<CR> ?<CR> UP<CR> DOWN<CR> 00<CR> ?<CR>
Z3 COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) Z3 COMMAND Invalid at AVR-988 and AVC-2808 for JAPAN

- 16 -

ANALOG TUNER ControlAVR Model Only COMMAND TF PARAMETER ANUP ANDOWN AN****** (6 digits) AN? ANUP ANDOWN AN**(PRESET No.) AN? ANMEM ANAM ANFM AN? ANAUTO ANMANUAL function TUNER Frequency UP/DOWN --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.) Return TF Status TUNER PRESET CH UP/DOWN , direct change to No.** example TFANUP<CR> TFANDOWN<CR> TFAN105000<CR> (1050.00kHz at AM) TFAN?<CR> TPANUP<CR> TPANDOWN<CR> TPANA1<CR> (PRESET No.A1) TPAN?<CR> TPANMEM<CR> TMANAM<CR> TMANFM<CR> TMAN?<CR> TMANAUTO<CR> TMANMANUAL<CR>
Return TP Status TUNER PRESET MEMORY TUNER BAND , MODE Select ---Band set to AM ---Band set to FM Return TM Status ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode
TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isnt TUNER.

- 17 -

XM Control(North America model only)
COMMAND TF PARAMETER XMUP XMDOWN XM*** (3 digits) XM? XMUP XMDOWN XM**(PRESET No.) XM? XMMEM ? function XM Channel UP/DOWN --- ***:XM CH No. Return TFXM Status XM PRESET CH UP/DOWN , direct change to No.** example TFXMUP<CR> TFXMDOWN<CR> TFXM001<CR> (XM001 CH at XM) TFXM?<CR> TPXMUP<CR> TPXMDOWN<CR> TPXMA1<CR> (PRESET No.A1) TPXM?<CR> TPXMMEM<CR> XM?<CR>
Return TPXM Status XM PRESET MEMORY Return XM Status - CHANNEL NAME, ARTIST, TITLE, SIGNAL LEVEL
TF, TP, XM COMMAND : '*' parameters can NOT operate when INPUT source isnt XM.

- 18 -

iPod Extended Control
COMMAND IP PARAMETER 94 9A 9C 9D 9E 9F 9G 9H 9I 9J 9K 9L 9M 9N 9P 9Q 9V 9W 9X 9Y function Cursor Up Control Cursor Down Control Cursor Left Control Cursor Right Control Enter (Play/Pause) Control Play/Pause Control Stop Control Skip Plus Control Skip Minus Control Manual Search Plus Control(ASD-1R Only) Manual Search Minus Control(ASD-1R Only) Repeat One Control Repeat All Control Repeat Off Control Shuffle Songs Control Shuffle Album Control Shuffle Off Control MENU Control Switch the Browse Mode Control(ASD-1R Only) Switch the Remote Mode Control(ASD-1R Only) Shuffle On Control(ASD-3N/W Only) Toggle Switch Browse Mode/Remote ModeControl Page Up Control Page Down Control Return Onscreen Display Information List Request Onscreen Display Information List(iPOD) (UTF-8 CODE Character ) example IP90<CR> IP91<CR> IP92<CR> IP93<CR> IP94<CR> IP9A<CR> IP9C<CR> IP9D<CR> IP9E<CR> IP9F<CR> IP9G<CR> IP9H<CR> IP9I<CR> IP9J<CR> IP9K<CR> IP9L<CR> IP9M<CR> IP9N<CR> IP9P<CR> IP9Q<CR> IP9V<CR> IP9W<CR> IP9X<CR> IP9Y<CR> IPA<CR> (Return IPA0-IPA9) IPE<CR> (Return IPE0-IPE9. Refer to Page 34

IPA IPE

IP, IPA, IPE COMMAND : '*' parameters can NOT operate when INPUT source isnt iPod. - 19 -

Cursol/Enter/Menu(Setup)

COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN MEN ON MEN OFF function Cursor Up Control Cursor Down Control Cursor Left Control Cursor Right Control Enter Control RETURN Control GUI Menu ON Control GUI Menu OFF Control example MNCUP<CR> MNCDN<CR> MNCLT<CR> MNCRT<CR> MNENT<CR> MNRTN<CR> MNMEN ON<CR> MNMEN OFF<CR>

- 20 -

Remote Lock/Panel Lock
COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF example SYREMOTE LOCK ON<CR> SYREMOTE LOCK OFF<CR> SYPANEL LOCK ON<CR> SYPANEL+V LOCK ON<CR> SYPANEL LOCK OFF<CR>

- 21 -

EVENT(or RESPONSE) and PARAMETER list
EVENT PW MV PARAMETER ON STANDBY ** function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 00 = -80dB 99 = ---(MIN) CHANNEL VOLUME change , **:00,38 to 62 by ASCII 62 = +12dB(MAX) 50 = 0dB 38 = -12dB(MIN) 00 = OFF (define ONLY SWch in DIRECT mode.) example PWON<CR> PWSTANDBY<CR> MV80<CR>
FL ** CVFL 50<CR> FR ** CVFR 50<CR> C ** CVC 50<CR> SW ** CVSW 50<CR> SL ** CVSL 50<CR> SR ** CVSR 50<CR> SBL ** CVSBL 50<CR> (at SBch 2SP) SBR ** CVSBR 50<CR> (at SBch 2SP) SB ** CVSB 50<CR> (at SBch 1SP) ON MUON<CR> MU OUTPUT MUTE ON/OFF change OFF MUOFF<CR> PHONO SIPHONO<CR> SI INPUT source change CD SICD<CR> TUNER SITUNER<CR> DVD SIDVD<CR> HDP SIHDP<CR> TV/CBL SITV/CBL<CR> SAT SISAT<CR> VCR SIVCR<CR> DVR SIDVR<CR> V.AUX SIV.AUX<CR> *RES. : NOT returns '*' parameters as RESPONSE. The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page4 J) section) CV

- 22 -

EVENT SI ZM SR
PARAMETER XM IPOD ON OFF PHONO | IPOD SOURCE AUTO HDMI DIGITAL ANALOG EXT.IN-1 AUTO PCM DTS DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE
function (North America model Only) MAIN-ZONE ON/OFF change REC SELECT source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. REC SELECT mode cancel INPUT mode change
---Set EXT.IN mode at AVR-2808 DIGITAL INPUT mode change VIDEO SELECT mode source change
example SIXM<CR> SIIPOD<CR> ZMON<CR> ZMOFF<CR> SRPHONO<CR> | SRAUXIPOD<CR> SRSOURCE<CR> SDAUTO<CR> SDHDMI<CR> SDDIGITAL<CR> SDANALOG<CR> SDEXT.IN-1<CR> DCAUTO<CR> DCPCM<CR> DCDTS<CR> SVDVD<CR> SVVDP<CR> SVTV/CBL<CR> SVSAT<CR> SVVCR<CR> SVDVR<CR> SVV.AUX<CR> SVSOURCE<CR>

- 23 -

EVENT MS
PARAMETER DIRECT PURE DIRECT STEREO MULTI CH IN MULTI CH IN +PL2x C MULTI CH IN +PL2x M MULTI CH DIRECT MULTI CH DIRECT +PL2x C MULTI CH DIRECT +PL2x M MULTI CH PURE D MULTI CH PURE D +PL2x C MULTI CH PURE D +PL2x M MULTI CH IN 7.1 M DIRECT 7.1 M CH PURE D 7.1 DOLBY PRO LOGIC DOLBY PL2 CINEMA DOLBY PL2 MUSIC DOLBY PL2 G DOLBY PL2x C DOLBY PL2x M DOLBY PL2x G DOLBY DIGITAL DOLBY D EX DOLBY D +PL2x C DOLBY D +PL2x M
function SURROUND mode change
example MSDIRECT<CR> MSPURE DIRECT<CR> MSSTEREO<CR> MSMULTI CH IN<CR> MSM CH IN+PL2X C<CR> MSM CH IN+PL2X M<CR> MSMULTI CH DIRECT<CR> MSM CH DRCT+PL2X C <CR> MSM CH DRCT+PL2X M <CR> MSMULTI CH PURE D<CR> MSM CH PURE D+PL2X C <CR> MSM CH PURE D+PL2X M <CR> MSMULTI CH IN 7.1<CR> MSM DIRECT 7.1<CR> MSM CH PURE D 7.1<CR> MSDOLBY PRO LOGIC<CR> MSDOLBY PL2 C<CR> MSDOLBY PL2 M<CR> MSDOLBY PL2 G<CR> MSDOLBY PL2X C<CR> MSDOLBY PL2X M<CR> MSDOLBY PL2X G<CR> MSDOLBY DIGITAL<CR> MSDOLBY D EX<CR> MSDOLBY D+PL2X C<CR> MSDOLBY D+PL2X M<CR>

- 24 -

PARAMETER DTS NEO:6 C DTS NEO:6 M DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.1 DTS+NEO:6 DTS+PL2x C DTS+PL2x M DTS96/24 DTS96 ES MTRX WIDE SCREEN 5CH STEREO 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL DSD DIRECT DSD PURE DIRECT DSD MULTI DRCT DSD MULTI PURE MPEG2 AAC AAC+DOLBY EX AAC+PL2x C AAC+PL2x M

JAPAN JAPAN JAPAN JAPAN

model model model model

Only Only Only Only

example MSDTS NEO:6 C<CR> MSDTS NEO:6 M<CR> MSDTS SURROUND<CR> MSDTS ES DSCRT6.1<CR> MSDTS ES MTRX6.1<CR> MSDTS+NEO:6<CR> MSDTS+PL2X C<CR> MSDTS+PL2X M<CR> MSDTS96/24<CR> MSDTS96 ES MTRX<CR> MSWIDE SCREEN<CR> MS5CH STEREO<CR> MS7CH STEREO<CR> MSSUPER STADIUM<CR> MSROCK ARENA<CR> MSJAZZ CLUB<CR> MSCLASSIC CONCERT<CR> MSMONO MOVIE<CR> MSMATRIX<CR> MSVIDEO GAME<CR> MSVIRTUAL<CR> MSDSD DIRECT<CR> MSDSD PURE DIRECT<CR> MSDSD MULTI DRCT<CR> MSDSD MULTI PURE<CR> MSMPEG2 AAC<CR> MSAAC+DOLBY EX<CR> MSAAC+PL2X C<CR> MSAAC+PL2X M<CR>

- 25 -

PARAMETER NEURAL DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2x C DOLBY D+ +PL2x M DOLBY TRUEHD DOLBY HD DOLBY HD+EX DOLBY HD+PL2x C DOLBY HD+PL2x M DTS HD DTS HD MSTR DTS EXPRESS DTS HD+NEO:6 DTS HD+PL2x C DTS HD+PL2x M DTS ES 8CH DSCRT QUICK1 QUICK2 QUICK3 QUICK0 ASPNRM ASPFUL SC48P SC10I SC72P SC10P SCAUTO
function (North America model Only)
QUICK SELECT mode change ---User 1(or User 2 or User 3) Change User OFF ASPECT setting change SCALER setting change
example MSNEURAL<CR> MSDOLBY D+<CR> MSDOLBY D+ +EX<CR> MSDOLBY D+ +PL2X C<CR> MSDOLBY D+ +PL2X M<CR> MSDOLBY HD<CR> MSDOLBY HD<CR> MSDOLBY HD+EX<CR> MSDOLBY HD+PL2X C<CR> MSDOLBY HD+PL2X M<CR> MSDTS HD<CR> MSDTS HD MSTR<CR> MSDTS EXPRESS<CR> MSDTS HD+NEO:6<CR> MSDTS HD+PL2X C<CR> MSDTS HD+PL2X M<CR> MSDTS ES 8CH DSCRT<CR> MSQUICK1<CR> MSQUICK2<CR> MSQUICK3<CR> MSQUICK0<CR> VSASPNRM<CR> VSASPFUL<CR> VSSC48P<CR> VSSC10I<CR> VSSC72P<CR> VSSC10P<CR> VSSCAUTO<CR>

- 26 -

EVENT PS
PARAMETER TONE DEFEAT ON TONE DEFEAT OFF SB:MTRX ON SB:NON MTRX SB:PL2xC SB:PL2xM SB:ON SB:OFF SB:ESDSCRT SB:ESMTRX CINEMA EQ.ON CINEMA EQ.OFF MODE:PL2X C MODE:PL2X M MODE:PL2X G MODE:PL2 C MODE:PL2 M MODE:PL2 G MODE:PRO LOGIC MODE:NEO:6 C MODE:NEO:6 M ROOM EQ:AUDYSSEY ROOM EQ:BYP.LR ROOM EQ:FLAT ROOM EQ:MANUAL ROOM EQ:OFF BAS ** TRE **
function TONE DEFEAT ON/OFF change SURROUND BACK MODE change
CINEMA EQ. ON/OFF Change CINEMA / MUSIC / GAME / PL mode change
ROOM EQ mode direct change
BASS change TREBLE change
example PSTONE DEFEAT ON<CR> PSTONE DEFEAT OFF<CR> PSSB:MTRX ON<CR> PSSB:NON MTRX<CR> PSSB:PL2X CINEMA<CR> PSSB:PL2X MUSIC<CR> PSSB:ON<CR> PSSB:OFF<CR> PSSB:ESDSCRT<CR> PSSB:ESMTRX<CR> PSCINEMA EQ.ON<CR> PSCINEMA EQ.OFF<CR> MODE:PL2X C<CR> MODE:PL2X M<CR> MODE:PL2X G<CR> MODE:PL2 C<CR> MODE:PL2 M<CR> MODE:PL2 G<CR> MODE:PRO LOGIC<CR> MODE:NEO:6 C<CR> MODE:NEO:6 M<CR> PSROOM EQ:AUDYSSEY<CR> PSROOM EQ:BYP.LR<CR> PSROOM EQ:FLAT<CR> PSROOM EQ:MANUAL<CR> PSROOM EQ:OFF<CR> PSBAS 00<CR> PSTRE 00<CR>

- 27 -

EVENT PS DRC DRC DRC DRC DRC DCO DCO DCO DCO DCO LFE EFF EFF EFF DEL AFD AFD PAN PAN DIM CEN CEI ATT ATT SWR SWR RSZ RSZ RSZ RSZ RSZ
PARAMETER AUTO LOW MID HI OFF OFF MID LOW MID HIGH ** ON OFF ** *** ON OFF ON OFF ** ** ** ON OFF ON OFF S MS M ML L
function DRC change PSDRC PSDRC PSDRC PSDRC PSDRC PSDCO PSDCO PSDCO PSDCO PSDCO PSLFE PSEFF PSEFF PSEFF PSDEL PSAFD PSAFD PSPAN PSPAN PSDIM PSCEN PSCEI PSATT PSATT PSSWR PSSWR PSRSZ PSRSZ PSRSZ PSRSZ PSRSZ

D.COMP change

LFE change EFFECT change EFFECT LEVEL change DELAY change AFDM change PANORAMA change DIMMENSION change CENTER WIDTH change CENTER IMAGE change SW ATT change SW ON/OFF change ROOM SIZE change
example AUTO<CR> LOW<CR> MID<CR> HI<CR> OFF<CR> OFF<CR> MID<CR> LOW<CR> MID<CR> HIGH<CR> 10<CR> UP<CR> DOWN<CR> **<CR> ***<CR> ON<CR> OFF<CR> ON<CR> OFF<CR> **<CR> 07<CR> 10<CR> ON<CR> OFF<CR> ON<CR> OFF<CR> S<CR> MS<CR> M<CR> ML<CR> L<CR>

- 28 -

PARAMETER DELAY *** NIGHT OFF NIGHT LOW NIGHT MID NIGHT HI RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3
function AUDIO DELAY change, ***:000 to 999 by ASCII ---AVR-2808200=200msMAX 100=100ms, 000=0ms NIGHT MODE change
example PSDELAY 200<CR> PSNIGHT OFF<CR> PSNIGHT LOW<CR> PSNIGHT MID<CR> PSNIGHT HI<CR> PSRSTR OFF<CR> PSRSTR MODE1<CR> PSRSTR MODE2<CR> PSRSTR MODE3<CR>

AUDIO RESTORER change

- 29 -

EVENT Z2

PARAMETER PHONO | IPOD SOURCE **

Z2MU Z2CS

ZONE2 Channel setting ---Invalid at AVR-988 Z2CV **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB Z2HPF ZONE2 HPF ON/OFF change ---Invalid at AVR-988 Z2PS ZONE2 BASS change ---Invalid at AVR-988 TRE ** ZONE2 TEBLE change ---Invalid at AVR-988 The PARAMETER of Z2 EVENT : Uses two ASCII characters. (see page4 J) section) The PARAMETER of Z2 EVENT :Invalid at AVC-2808 for JAPAN
ON OFF ON OFF ST MONO FL ** FR ** ON OFF BAS **
function MULTI ZONE-2 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. MULTI ZONE-2 mode cancel MULTI ZONE-2 VOLUME change , **:10 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 10 = -70dB 99 = ---(MIN) MULTI ZONE-2 ON/OFF change ZONE2 OUTPUT MUTE ON/OFF change
example Z2PHONO<CR> | Z2IPOD<CR> Z2SOURCE<CR> Z280<CR>
Z2ON<CR> Z2OFF<CR> Z2MUON<CR> Z2MUOFF<CR> Z2CSST Z2CSMONO Z2CVFL 50<CR> Z2CVFR 50<CR> Z2HPFON<CR> Z2HPFOFF<CR> Z2PSBAS 00<CR> Z2PSTRE 00<CR>

- 30 -

EVENT Z3
PARAMETER PHONO | AUXIPOD SOURCE **
ON OFF ON Z3MU ZONE3 OUTPUT MUTE ON/OFF change OFF ST Z3CS ZONE3 Channel setting MONO FL ** Z3CV **:38 to 62 by ASCII , 50=0dB FR ** **:38 to 62 by ASCII , 50=0dB ON Z3HPF ZONE3 HPF ON/OFF change OFF BAS ** Z3PS ZONE3 BASS change TRE ** ZONE3 TEBLE change The PARAMETER of Z3 EVENT : Uses two ASCII characters. (see page4 J) section) The PARAMETER of Z3 EVENT : Invalid at AVR-988 and AVC-2808 for JAPAN
function MULTI ZONE-3 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. MULTI ZONE-3 mode cancel MULTI ZONE-3 VOLUME change , **:10 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 10 = -70dB 99 = ---(MIN) MULTI ZONE-3 ON/OFF change
example Z3PHONO<CR> | Z3AUXIPOD<CR> Z3SOURCE<CR> Z380<CR>
Z3ON<CR> Z3OFF<CR> Z3MUON<CR> Z3MUOFF<CR> Z3CSST Z3CSMONO Z3CVFL 50<CR> Z3CVFR 50<CR> Z3HPFON<CR> Z3HPFOFF<CR> Z3PSBAS 00<CR> Z3PSTRE 00<CR>

- 31 -

ANALOG TUNER ControlAVR Model Only
EVENT TF PARAMETER AN****** (6 digits) AN**(PRESET No.) ANAM ANFM ANAUTO ANMANUAL function TUNER Frequency change --- ****.** kHz at AM band ****.** MHz at FM band TUNER PRESET change to No.** TUNER BAND , MODE change ---Band set to AM ---Band set to FM ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode example TFAN105000<CR> (1050.00kHz at AM) TPANA1<CR> (PRESET No.A1) TMANAM<CR> TMANFM<CR> TMANAUTO<CR> TMANMANUAL<CR>

- 32 -

EVENT TF TP XM PARAMETER XM*** (3 digits) XM**(PRESET No.) CH NAME ******** (8 digit) ARTIST **************** (16 digit) TITLE **************** (16 digit) XMID ******** (8 digit) SIGNAL GOOD SIGNAL WEAK SIGNAL MARGINAL SIGNAL NOSIGNAL function --- ***:XM CH No. XM PRESET change to No.** XM CH NAME change XM ARTIST NAME change XM TITLE NAME change XM RADIO ID(XM000 Selected) XM ANTENNA SIGNAL STATUS change example TFXM001<CR> (XM001 CH) TPXMA1<CR> (PRESET No.A1) TMCH NAME 20 on 20<CR> TMARTIST EMINEM TMTITLE JUST LOSE IT TMXMID J3JU703B<CR> TMSIGNAL TMSIGNAL TMSIGNAL TMSIGNAL GOOD<CR> WEAK<CR> MARGINAL<CR> NOSIGNAL<CR> <CR> <CR>

- 33 -

EVENT IPA PARAMETER function Onscreen Display Information is Answered By the IPA Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Infromation ---ASD-3N/3W Connect Display Information is blank Display Line10 Information Display Line11 Information example

IPA0***************_???<CR> IPA1*************_???<CR> IPA2*************_???<CR> IPA3*************_???<CR> IPA4*************_???<CR> IPA5*************_???<CR> IPA6*************_???<CR> IPA7*************_???<CR> IPA8#**************_???<CR> IPA9***************_???<CR> *:Character Length MAX96 _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor Infomation Data(1Byte) Bit1:Playable Music=1 Bit2:Display Only=1 Bit3:Don't Care Bit4:CURSOR SELECT=1 Bit5-8:Don't Care #iPod dock Information Data(1Byte) Bit1Unkown=1 Bit2:ASD-1R=1 Bit3:ASD-3N/3W=1 Bit4-8:Dont Care

- 34 -

EVENT IPA

PARAMETER

example <example1-for ASD-1R> IPA0Artist??????????????????<CR> IPA1 Ana Caram_????????????<CR> IPA2 Badi Assad_???????????<CR> IPA3 Christy Baron_????????<CR> IPA4 Marta Gomez_??????????<CR> IPA5 Rebecca Pidgeon_??????<CR> IPA6 Sara K_???????????????<CR> IPA7 Valerie Joyce_????????<CR> IPA8# SFL Songs RPT All_???<CR> IPA9 [ 2/ 6]_?????????<CR> <example2-for ASD-1R> IPA0Now Playing iPod_???????<CR> IPA1 A HARD DAY'S NIGHT._??<CR> IPA2 /The Beatles_?????????<CR> IPA3_??????????????????????<CR> IPA4 A HARD DAY'S NIGHT_???<CR> IPA5 00:04_??????????????<CR> IPA6_??????????????????????<CR> IPA7_??????????????????????<CR> IPA8# SFL Songs RPT All_???<CR> IPA9_????????????????????????<CR>

- 35 -

example <example1-for ASD-3N/W> IPA0Artist??????????????????<CR> IPA1Ana Caram_????????????<CR> IPA2Badi Assad_???????????<CR> IPA3Christy Baron_????????<CR> IPA4Marta Gomez_??????????<CR> IPA5Rebecca Pidgeon_??????<CR> IPA6Sara K_???????????????<CR> IPA7_?????????????????????<CR> IPE8# SFL On RPT All_???<CR> IPA9 [ 2/ 6]_?????????<CR> <example2-for ASD-3N/W> IPA0Now Playing iPod_???????<CR> IPA1 A HARD DAY'S NIGHT._??<CR> IPA2 /The Beatles_?????????<CR> IPA3_??????????????????????<CR> IPA4 A HARD DAY'S NIGHT_???<CR> IPA5 00:04_??????????????<CR> IPA6_??????????????????????<CR> IPA7_??????????????????????<CR> IPE8# SFL On RPT All_???<CR> IPA9_???????????????????????<CR>

- 36 -

EVENT IPE 8 9
function Onscreen Display Information(iPOD) is Answered By the IPA Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information ---ASD-3N/3W Connect Display Information is blank Display Line10 Information Display Line11 Information

example

IPE0***************_???<CR> IPE1*************_???<CR> IPE2*************_???<CR> IPE3*************_???<CR> IPE4*************_???<CR> IPE5*************_???<CR> IPE6*************_???<CR> IPE7*************_???<CR> IPE8#**************_???<CR> IPE9***************_???<CR> *:UTF-8 CODE Character(MAX95byte) _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor Infomation Data(1Byte) Bit1:Playable Music=1 Bit2:Display Only=1 Bit3:Don't Care Bit4:CURSOR SELECT=1 Bit5-8:Don't Care #iPod dock Information Data(1Byte) Bit1Unkown=1 Bit2:ASD-1R=1 Bit3:ASD-3N/3W=1 Bit4-8:Dont Care ************_?????:96byte Fixed