DENON AVR control protocol

Ver. 5.2.0_a

Application model : AVR-3808/AVC-3808 Application terminal: RS-232C/ Ethernet

Connector specification

. RS-232C Connector type: DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC ) Communication format: Synchronous system : Tone step synchronization Communication system : A half duplex Communication speed : 9600bps Character length : 8 bits Parity control : None Start bit : 1 bit Stop bit : 1 bit Communication procedure : Non procedural Communication data length : 135 bytes (maximum)

Version 5.2.0 5.2.0_a

Date 06.Jul.07 23.Jan.08
Contents Original 1.Added NSE,NSB,NSC for iRadio Control. 2.Corrected the Command of IPE,IPA for iPod Control. 3.Added Response MS Command for DTS Mode. 4.Corrected the Response Command of PSMODE.
Page 23,39 24,40,41,42,43 30,31 32
. Ethernet Connector type Example
RJ-45(10BASE-T/100BASE-TX)

Ethernet Cross cable

AVR/AVC

Example

HUB PC Ethernet Straight cable Ethernet Straight cable AVR/AVC
Communication format Communication Communication Communication Communication
system speed port data length

: : : :

A half duplex 10Mbps/100Mbps TCP port 23 (telnet) 135bytes (maximum)
NETWORK SETUP of AVR-4308 >Procedure of Network Setup mode. (1)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and GUI) (2)Select Network Setup > Detail. (3)Set parameters described below. <DHCP> "ON"---Use this setting when DHCP server is on the local network. "OFF"---Use this setting when DHCP server is not on the local network. <IP Address> When <DHCP> sets "OFF, please set IP address. When <DHCP> sets "ON, you can confirm the IP address that is set by server. <Subnet Mask> When <DHCP> sets "OFF, please set Subnet Mask. When <DHCP> sets "ON, you can confirm the Subnet Mask that is set by server. <Gateway> Set the address of Gateway when Gateway is on the local network. Do not set this parameter when Gateway is not on the local network. <Primary DNS> Do not set this parameter. <Second DNS> Do not set this parameter. <Proxy> Set this parameter "OFF". <Network Option: Standby Mode Power Saving> (1)Press MENU button, then Menu appears on FL-display (and GUI) (2)Select Manual Setup > Network Setup > Other > Power Saving (3)Set parameters described below. OFF---Use this setting when using the AVR-4308 connected in a network. ON--- Use this setting when not using the AVR-4308 connected in a network. This setting is reducing the power consumption in the standby mode.
NETWORK SETUP of AVR-3808 >Procedure of Network Setup mode. (1)Press SYSTEM SETUP button, then System Setup Menu appears on FL-display(and GUI) (2)Select Network Setup > Detail. (3)Set parameters described below. <DHCP> "ON"---Use this setting when DHCP server is on the local network. "OFF"---Use this setting when DHCP server is not on the local network. <IP Address> When <DHCP> sets "OFF, please set IP address. When <DHCP> sets "ON, you can confirm the IP address that is set by server. <Subnet Mask> When <DHCP> sets "OFF, please set Subnet Mask. When <DHCP> sets "ON, you can confirm the Subnet Mask that is set by server. <Gateway> Set the address of Gateway when Gateway is on the local network. Do not set this parameter when Gateway is not on the local network. <Primary DNS> Do not set this parameter. <Second DNS> Do not set this parameter. <Proxy> Set this parameter "OFF". <Network Option: Standby Mode Power Saving> (1)Press MENU button, then Menu appears on FL-display (and GUI) (2)Select Manual Setup > Network Setup > Other > Power Saving (3)Set parameters described below. OFF---Use this setting when using the AVR-3808 connected in a network. ON--- Use this setting when not using the AVR-4308 connected in a network. This setting is reducing the power consumption in the standby mode.
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT. RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR) if the request command (COMMAND+?+CR(0x0D)) has came from a controller. The RESPONSE should be sent within 200ms of receiving the COMMAND. *The form of RESPONSE presupposes that it is the same as that of EVENT.

COMMAND and PARAMETER list
COMMAND PW PARAMETER function example ON POWER ON/STANDBY change PWON<CR> STANDBY PWSTANDBY<CR> ? Return PW Status PW?<CR> MV UP MASTER VOLUME UP/DOWN , direct change to **dB MVUP<CR> DOWN MVDOWN<CR> ** **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) MV80<CR> ? Return MV Status MV?<CR> CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP<CR> FL DOWN ---FRONT Lch CVFL DOWN<CR> FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50<CR> FR UP CVFR UP<CR> FR DOWN ---FRONT Rch CVFR DOWN<CR> FR ** **:38 to 62 by ASCII , 50=0dB CVFR 50<CR> C UP CVC UP<CR> C DOWN ---CENTERch CVC DOWN<CR> C ** **:38 to 62 by ASCII , 50=0dB CVC 50<CR> SW UP CVSW UP<CR> SW DOWN ---SUBWOOFERch CVSW DOWN<CR> SW ** **:00,38 to 62 by ASCII , 50=0dB,00=OFF CVSW 50<CR> SL UP CVSL UP<CR> SL DOWN ---SURROUND Lch CVSL DOWN<CR> SL ** **:38 to 62 by ASCII , 50=0dB CVSL 50<CR> SR UP CVSR UP<CR> SR DOWN ---SURROUND Rch CVSR DOWN<CR> SR ** **:38 to 62 by ASCII , 50=0dB CVSR 50<CR> SBL UP ---SURROUND BACK Lch (SBch 2SP) CVSBL UP<CR> SBL DOWN CVSBL DOWN<CR> SBL ** **:38 to 62 by ASCII , 50=0dB CVSBL 50<CR> SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP<CR> SBR DOWN CVSBR DOWN<CR> SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50<CR> MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section) -9-

COMMAND CV

PARAMETER function SB UP ---SURROUND BACKch (SBch 1SP) SB DOWN SB ** **:00 to 99 by ASCII , 50=0dB ? Return CV Status MU ON OUTPUT MUTE ON/OFF change OFF ? Return MU Status SI PHONO Select INPUT source CD TUNER DVD HDP TV/CBL SAT VCR DVR V.AUX NET/USB XM (North America model Only) IPOD ? Return SI Status ZM ON MAIN-ZONE ON/OFF change at AVR-3808 OFF ? Return ZM Status SR PHONO REC SELECT mode set , and select source | ---The name of PARAMETER is IPOD the same as that of the time of SI COMMAND. SOURCE REC SELECT mode cancel ? Return SR Status CV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)
example CVSB UP<CR> CVSB DOWN<CR> CVSB 50<CR> CV?<CR> MUON<CR> MUOFF<CR> MU?<CR> SIPHONO<CR> SICD<CR> SITUNER<CR> SIDVD<CR> SIHDP<CR> SITV/CBL<CR> SISAT<CR> SIVCR<CR> SIDVR<CR> SIV.AUX<CR> SINET/USB<CR> SIXM<CR> SIIPOD<CR> SI?<CR> ZMON<CR> ZMOFF<CR> ZM?<CR> SRPHONO<CR> | SRIPOD<CR> SRSOURCE<CR> SR?<CR>

- 10 -

COMMAND SD
PARAMETER AUTO HDMI DIGITAL ANALOG EXT.IN-1 ? AUTO PCM DTS ? DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE ? DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND NEURAL WIDE SCREEN 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB
function set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical,Coaxial)mode set force ANALOG INPUT mode ---Set EXT.IN mode at AVR-3808 Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set , and select source
VIDEO SELECT mode cancel Return SV Status Select SURROUND mode
(North America model Only)
example SDAUTO<CR> SDHDMI<CR> SDDIGITAL<CR> SDANALOG<CR> SDEXT.IN-1<CR> SD?<CR> DCAUTO<CR> DCPCM<CR> DCDTS<CR> DC? SVDVD<CR> SVVDP<CR> SVTV/CBL<CR> SVSAT<CR> SVVCR<CR> SVDVR<CR> SVV.AUX<CR> SVSOURCE<CR> SV?<CR> MSDIRECT<CR> MSPURE DIRECT<CR> MSSTEREO<CR> MS STANDARD<CR> MSDOLBY DIGITAL<CR> MSDTS SURROUND<CR> MS NEURAL<CR> MSWIDE SCREEN MS7CH STEREO<CR> MSSUPER STADIUM<CR> MSROCK ARENA<CR> MSJAZZ CLUB<CR>

- 11 -

COMMAND MS
PARAMETER CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL MPEG2 AAC ? QUICK1 QUICK2 QUICK3 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK ? MONIAUTO MONI1 MONI2 MONI? ASPNRM ASPFUL ASP? SC48P SC10I SC72P SC10P SC AUTO SC?

function

---Invalid at AVR model (Japan model only) Return MS Status QUICK SELECT 1-3 MODE SELECT USER1-3 MODE MEMORY Return MSQUICK Status Set HDMI MONITOR automatic detection (Japan model only) Set HDMI MONITOR OUT-1 (Japan model only) Set HDMI MONITOR OUT-2 (Japan model only) Return VSMONITOR Status (Japan model only) Set Normal mode Set FULL mode Return VSASPECT Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolution to 1080p Set Resolution to AUTO Return VSSCALE Status
example MSCLASSIC CONCERT<CR> MSMONO MOVIE<CR> MSMATRIX<CR> MSVIDEO GAME<CR> MSVIRTUAL<CR> MSMPEG2 AAC<CR> MS?<CR> MSQUICK1<CR> MSQUICK2<CR> MSQUICK3<CR> MSQUICK1 MEMORY<CR> MSQUICK2 MEMORY<CR> MSQUICK3 MEMORY<CR> MSQUICK ?<CR> VSMONIAUTO<CR> VSMONI1<CR> VSMONI2<CR> VSMONI?<CR> VSASPNRM<CR> VSASPFUL<CR> VSASP?<CR> VSSC48P<CR> VSSC10I<CR> VSSC72P<CR> VSSC10P<CR> VSSCAUTO<CR> VSSC?<CR>

- 12 -

COMMAND PS
PARAMETER TONE DEFEAT ON TONE DEFEAT OFF TONE DEFEAT ? SB:MTRX ON SB:NON MTRX SB:PL2xCINEMA SB:PL2xMUSIC SB:ON SB:OFF SB: ? CINEMA EQ.ON CINEMA EQ.OFF CINEMA EQ. ? MODE:MUSIC MODE:CINEMA MODE:GAME MODE:PRO LOGIC

example UP<CR> DOWN<CR> 50<CR> ?<CR> AUTO<CR> LOW<CR> MID<CR> HI<CR> OFF<CR> ?<CR> OFF<CR> LOW<CR> MID<CR> HIGH<CR> ?<CR> UP<CR> DOWN<CR> 10<CR> ? <CR> UP<CR> DOWN<CR> **<CR> ?<CR> UP<CR> DOWN<CR> ***<CR> ?<CR> ON<CR> OFF<CR> ?<CR>

- 14 -

PARAMETER function example PAN ON PSPAN ON<CR> PANORAMA ON/OFF PAN OFF PSPAN OFF<CR> PAN ? PSPAN ?<CR> Return PSPAN Status DIM UP PSDIM UP<CR> DIMENSION UP/DOWN , direct change to **dB DIM DOWN PSDIM DOWN<CR> **:00 to 99 by ASCII , 00=0, DIM ** PSDIM **<CR> ---AVR-3808 can be operated from 0 to 6 DIM ? PSDIM ?<CR> Return PSDIM Status CEN UP PSCEN UP<CR> CENTER WIDTH UP/DOWN , direct change to **dB CEN DOWN PSCEN DOWN<CR> **:00 to 99 by ASCII , 00=0 CEN ** PSCEN 07<CR> ---AVR-3808 can be operated from 0 to 7 CEN ? PSCEN ?<CR> Return PSCEN Status CEI UP PSCEI UP<CR> CENTER IMAGE UP/DOWN , direct change to **dB CEI DOWN PSCEI DOWN<CR> **:00 to 99 by ASCII , 00=0.0 CEI ** PSCEI 10<CR> ---AVR-3808 can be operated from 0.0 to 1.0 CEI? OSCEI ?<CR> Return PSCEI Status ATT ON PSATT ON<CR> SW ATT ON/OFF ATT OFF PSATT OFF<CR> ATT ? PSATT ?<CR> Return PSATT Status SWR ON PSSWR ON<CR> SW ON/OFF SWR OFF PSSWR OFF<CR> SWR ? PSSWR ?<CR> Return PSSWR Status RSZ S PSRSZ S<CR> ROOM SIZE direct change RSZ MS PSRSZ MS<CR> RSZ M PSRSZ M<CR> RSZ ML PSRSZ ML<CR> RSZ L PSRSZ L<CR> RSZ ? PSRSZ ?<CR> Return PSRSZ Status DELAY UP AUDIO DELAY UP/DOWN , direct change to ***dB PSDELAY UP<CR> DELAY DOWN ***:000 to 999 by ASCII , 000=0ms, 200=200ms PSDELAY DOWN<CR> DELAY *** ---AVR-3808 can be operated from 0 to 200 PSDELAY 200<CR> PS COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)

- 15 -

PARAMETER function NIGHT OFF NIGHT MODE direct change NIGHT LOW NIGHT MID NIGHT HI NIGHT ? Return PSNIGHT Status RSTR OFF AUDIO RESTORER direct change RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? Return PSRSTR Status PV CN UP CONTRAST UP/DOWN , direct change to **dB CN DOWN **:44 to 56 by ASCII , 50=0 CN ** ---AVR-3808 can be operated from -6 to +6(44 to 56) CN ? Return PSCN Status BR UP BRIGHTNESS UP/DOWN , direct change to **dB BR DOWN **:00 to 12 by ASCII , 00=0 BR ** ---AVR-3808 can be operated from 0 to 12 BR ? Return PSBR Status CM UP CROMA LEVET UP/DOWN , direct change to **dB CM DOWN **:44 to 56 by ASCII , 50=0 CM ** ---AVR-3808 can be operated from -6 to +6(44 to 56) CM ? Return PSCN Status HUE UP HUE UP/DOWN , direct change to **dB HUE DOWN **:44 to 56 by ASCII , 50=0 HUE ** ---AVR-3808 can be operated from -6 to +6(44 to 56) HUE ? Return PSCN Status PV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)

example PSNIGHT OFF<CR> PSNIGHT LOW<CR> PSNIGHT MID<CR> PSNIGHT HI<CR> PSNIGHT ?<CR> PSRSTR OFF<CR> PSRSTR MODE1<CR> PSRSTR MODE2<CR> PSRSTR MODE3<CR> PSRSTR ?<CR> PVCN UP<CR> PVCN DOWN<CR> PVCN 06<CR> PVCN ?<CR> PVBR UP<CR> PVBR DOWN<CR> PVBR 12<CR> PVBR ?<CR> PVCM UP<CR> PVSCM DOWN<CR> PVCM 06<CR> PVCM ?<CR> PVHUE UP<CR> PVHUE DOWN<CR> PVHUE 06<CR> PVHUE ?<CR>

- 16 -

COMMAND Z2

Z2MU Z2CS Z2CV

PARAMETER PHONO | IPOD SOURCE UP DOWN ** ON OFF ? ON OFF ? ST MONO ? FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? ON OFF ?
function MULTI ZONE-2 mode set , and select source at AVR-3808 ---The name of PARAMETER is the same as that of the time of SI COMMAND. MULTI ZONE-2 mode cancel at AVR-3808 MULTI ZONE-2 VOLUME UP/DOWN , direct change to **dB at AVR-3808 **:10 to 99 by ASCII , 80=0dB, 99=---(MIN) MULTI ZONE-2 ON/OFF change at AVR-3808 Return Z2 Status ZONE2 OUTPUT MUTE ON/OFF change Return Z2MU Status ZONE2 Channel setting Return Z2CS Status ZONE2 CHANNEL VOLUME ---FRONT Lch **:38 to 62 by ASCII ZONE2 CHANNEL VOLUME ---FRONT Rch **:38 to 62 by ASCII Return Z2CV Status ZONE2 HPF ON/OFF Return Z2HPF Status UP/DOWN , direct change to **dB , 50=0dB UP/DOWN , direct change to **dB , 50=0dB
example Z2PHONO<CR> | Z2IPOD<CR> Z2SOURCE<CR> Z2UP<CR> Z2DOWN<CR> Z280<CR> Z2ON<CR> Z2OFF<CR> Z2?<CR> Z2MUON<CR> Z2MUOFF<CR> Z2MU?<CR> Z2CSST Z2CSMONO Z2CS? Z2CVFL UP<CR> Z2CVFL DOWN<CR> Z2CVFL 50<CR> Z2CVFR UP<CR> Z2CVFR DOWN<CR> Z2CVFR 50<CR> Z2CV?<CR> Z2HPFON<CR> Z2HPFOFF<CR> Z2HPF?<CR>
Z2 COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)

- 17 -

Except Japan model. COMMAND PARAMETER Z2PS BAS UP BAS DOWN BAS ** BAS ? TRE UP TRE DOWN TRE ** TRE ?
function ZONE2 BASS UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB ---AVR-3808 can be operated from -10 to +10(40 to 60) Return Z2PSBAS Status ZONE2 TREBLE UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB ---AVR-3808 can be operated from -10 to +10(40 to 60) Return Z2PSTRE Status
Z2PSBAS Z2PSBAS Z2PSBAS Z2PSBAS Z2PSTRE Z2PSTRE Z2PSTRE Z2PSTRE
example UP<CR> DOWN<CR> 00<CR> ?<CR> UP<CR> DOWN<CR> 00<CR> ?<CR>

- 18 -

Except Japan model COMMAND PARAMETER Z3 PHONO | IPOD SOURCE UP DOWN ** ON OFF ? Z3MU ON OFF ? Z3CS ST MONO ? Z3CV FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? Z3HPF ON OFF ?
function MULTI ZONE-3 mode set , and select source at AVR-3808 ---The name of PARAMETER is the same as that of the time of SI COMMAND. MULTI ZONE-3 mode cancel MULTI ZONE-3 VOLUME UP/DOWN , direct change to **dB **:10 to 99 by ASCII , 80=0dB, 99=---(MIN) MULTI ZONE-3 ON/OFF change at AVR-3808 Return Z3 Status ZONE3 OUTPUT MUTE ON/OFF change Return Z3MU Status ZONE3 Channel setting Return Z3CS Status ZONE3 CHANNEL VOLUME ---FRONT Lch **:38 to 62 by ASCII ZONE3 CHANNEL VOLUME ---FRONT Rch **:38 to 62 by ASCII Return Z2CV Status ZONE3 HPF ON/OFF Return Z3HPF Status UP/DOWN , direct change to **dB , 50=0dB UP/DOWN , direct change to **dB , 50=0dB

NSA NSE NSB NSC NSD ** ** *

- 23 -

iPod Extended Control
COMMAND IP PARAMETER 94 9A 9C 9D 9E 9F 9G 9H 9I 9J 9K 9L 9M 9N 9P 9Q 9X 9Y function Cursor Up Control Cursor Down Control Cursor Left Control Cursor Right Control Enter (Play/Pause) Control Play/Pause Control Stop Control Skip Plus Control Skip Minus Control Manual Search Plus Control Manual Search Minus Control Repeat One Control Repeat All Control Repeat Off Control Shuffle Songs Control Shuffle Album Control Shuffle Off Control MENU Control Switch the Browse Mode Control Switch the Remote Mode Control Page Up Control Page Down Control Return Onscreen Display Information List (ASCII CODE Character) Request Onscreen Display Information List(iPOD) (UTF-8 CODE Character) example IP90<CR> IP91<CR> IP92<CR> IP93<CR> IP94<CR> IP9A<CR> IP9C<CR> IP9D<CR> IP9E<CR> IP9F<CR> IP9G<CR> IP9H<CR> IP9I<CR> IP9J<CR> IP9K<CR> IP9L<CR> IP9M<CR> IP9N<CR> IP9P<CR> IP9Q<CR> IP9X<CR> IP9Y<CR> IPA<CR> (Return IPA0-IPA9,Refer to Page 40-41 IPE<CR> (Return IPE0-IPE9,Refer to Page 42-43

IPA IPE

- 24 -

Cursol/Enter/Menu(Setup)

COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN MEN ON MEN OFF function Cursor Up Control Cursor Down Control Cursor Left Control Cursor Right Control Enter Control RETURN Control GUI Menu ON Control GUI Menu OFF Control MNCUP<CR> MNCDN<CR> MNCLT<CR> MNCRT<CR> MNENT<CR> MNRTN<CR> MNMEN ON<CR> MNMEN OFF<CR> example

- 25 -

Remote Lock/Panel Lock
COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF example SYREMOTE LOCK ON<CR> SYREMOTE LOCK OFF<CR> SYPANEL LOCK ON<CR> SYPANEL+V LOCK ON<CR> SYPANEL LOCK OFF<CR>

- 26 -

EVENT(or RESPONSE) and PARAMETER list
EVENT PW MV PARAMETER ON STANDBY ** function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 00 = -80dB 99 = ---(MIN) CHANNEL VOLUME change , **:00,38 to 62 by ASCII 62 = +12dB(MAX) 50 = 0dB 38 = -12dB(MIN) 00 = OFF (define ONLY SWch in DIRECT mode.) example PWON<CR> PWSTANDBY<CR> MV80<CR>

FL ** CVFL 50<CR> FR ** CVFR 50<CR> C ** CVC 50<CR> SW ** CVSW 50<CR> SL ** CVSL 50<CR> SR ** CVSR 50<CR> SBL ** (at SBch 2SP) CVSBL 50<CR> SBR ** (at SBch 2SP) CVSBR 50<CR> SB ** (at SBch 1SP) CVSB 50<CR> MU ON OUTPUT MUTE ON/OFF change MUON<CR> OFF MUOFF<CR> SI PHONO INPUT source change SIPHONO<CR> CD SICD<CR> TUNER SITUNER<CR> DVD SIDVD<CR> HDP SIHDP<CR> TV/CBL SITV/CBL<CR> SAT SISAT<CR> VCR SIVCR<CR> DVR SIDVR<CR> V.AUX SIV.AUX<CR> The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page4 J) section)

- 27 -

EVENT SI
PARAMETER NET/USB XM USB IPOD ON OFF PHONO | IPOD SOURCE AUTO HDMI DIGITAL ANALOG EXT.IN-1 AUTO PCM DTS DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE
function (North America model Only) MAIN-ZONE ON/OFF change REC SELECT source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. REC SELECT mode cancel INPUT mode change
---Set EXT.IN mode at AVR-3808 DIGITAL INPUT mode change VIDEO SELECT mode source change
example SINET/USB<CR> SIHDRADIO<CR> SIUSB<CR> SIIPOD<CR> ZMON<CR> ZMOFF<CR> SRPHONO<CR> | SRAUXIPOD<CR> SRSOURCE<CR> SDAUTO<CR> SDHDMI<CR> SDDIGITAL<CR> SDANALOG<CR> SDEXT.IN-1<CR> DCAUTO<CR> DCPCM<CR> DCDTS<CR> SVDVD<CR> SVVDP<CR> SVTV/CBL<CR> SVSAT<CR> SVVCR<CR> SVDVR<CR> SVV.AUX<CR> SVSOURCE<CR>

- 28 -

EVENT MS
PARAMETER DIRECT PURE DIRECT STEREO MULTI CH IN MULTI CH IN +PL2x C MULTI CH IN +PL2x M MULTI CH DIRECT MULTI CH DIRECT +PL2x C MULTI CH DIRECT +PL2x M MULTI CH PURE D MULTI CH PURE D +PL2x C MULTI CH PURE D +PL2x M MULTI CH IN 7.1 M DIRECT 7.1 M CH PURE D 7.1 DOLBY PRO LOGIC DOLBY PL2 CINEMA DOLBY PL2 MUSIC DOLBY PL2 G DOLBY PL2x C DOLBY PL2x M DOLBY PL2x G DOLBY DIGITAL DOLBY D EX DOLBY D +PL2x C DOLBY D +PL2x M
function SURROUND mode change
example MSDIRECT<CR> MSPURE DIRECT<CR> MSSTEREO<CR> MSMULTI CH IN<CR> MSM CH IN+PL2X C<CR> MSM CH IN+PL2X M<CR> MSMULTI CH DIRECT<CR> MSM CH DRCT+PL2X C <CR> MSM CH DRCT+PL2X M <CR> MSMULTI CH PURE D<CR> MSM CH PURE D+PL2X C <CR> MSM CH PURE D+PL2X M <CR> MSMULTI CH IN 7.1<CR> MSM DIRECT 7.1<CR> MSM CH PURE D 7.1<CR> MSDOLBY PRO LOGIC<CR> MSDOLBY PL2 C<CR> MSDOLBY PL2 M<CR> MSDOLBY PL2 G<CR> MSDOLBY PL2X C<CR> MSDOLBY PL2X M<CR> MSDOLBY PL2X G<CR> MSDOLBY DIGITAL<CR> MSDOLBY D EX<CR> MSDOLBY D+PL2X C<CR> MSDOLBY D+PL2X M<CR>

- 29 -

PARAMETER DTS NEO:6 C DTS NEO:6 M DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.1 DTS+PL2x C DTS+PL2x M DTS+NEO:6 DTS96/24 DTS96 ES MTRX WIDE SCREEN 5CH STEREO 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL DSD DIRECT DSD PURE DIRECT DSD MULTI DRCT DSD MULTI PURE MPEG2 AAC AAC+DOLBY EX AAC+PL2x C AAC+PL2x M

JAPAN JAPAN JAPAN JAPAN

model model model model

Only Only Only Only

example MSDTS NEO:6 C<CR> MSDTS NEO:6 M<CR> MSDTS SURROUND<CR> MSDTS ES DSCRT6.1<CR> MSDTS ES MTRX6.1<CR> MSDTS+PL2X C<CR> MSDTS+PL2X M<CR> MSDTS+NEO:6<CR> MSDTS96/24<CR> MSDTS96 ES MTRX<CR> MSWIDE SCREEN<CR> MS5CH STEREO<CR> MS7CH STEREO<CR> MSSUPER STADIUM<CR> MSROCK ARENA<CR> MSJAZZ CLUB<CR> MSCLASSIC CONCERT<CR> MSMONO MOVIE<CR> MSMATRIX<CR> MSVIDEO GAME<CR> MSVIRTUAL<CR> MSDSD DIRECT<CR> MSDSD PURE DIRECT<CR> MSDSD MULTI DRCT<CR> MSDSD MULTI PURE<CR> MSMPEG2 AAC<CR> MSAAC+DOLBY EX<CR> MSAAC+PL2X C<CR> MSAAC+PL2X M<CR>

- 30 -

PARAMETER function NEURAL (North America model Only) DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2x C DOLBY D+ +PL2x M DOLBY TRUEHD DOLBY HD DOLBY HD+EX DOLBY HD+PL2x C DOLBY HD+PL2x M DTS HD DTS HD MSTR DTS HD+NEO:6 DTS HD+PL2X C DTS HD+PL2X M DTS ES 8CH DSCRT QUICK1 QUICK SELECT mode change QUICK2 QUICK3 QUICK0 ---User 1(or User 2 or User 3) Change User OFF MONIAUTO HDMI MONITOR setting change MONI1 MONI2 ASPNRM ASPECT setting change ASPFUL SC48P SCALER setting change SC10I SC72P SC10P SCAUTO
example MSNEURAL<CR> MSDOLBY D+<CR> MSDOLBY D+ +EX<CR> MSDOLBY D+ +PL2X C<CR> MSDOLBY D+ +PL2X M<CR> MSDOLBY HD<CR> MSDOLBY HD<CR> MSDOLBY HD+EX<CR> MSDOLBY HD+PL2X C<CR> MSDOLBY HD+PL2X M<CR> MSDTS HD<CR> MSDTS HD MSTR<CR> MSDTS HD+NEO:6<CR> MSDTS HD+PL2X C<CR> MSDTS HD+PL2X M<CR> MSDTS ES 8CH DSCRT<CR> MSQUICK1<CR> MSQUICK2<CR> MSQUICK3<CR> MSQUICK0<CR> VSMONIAUTO<CR> VSMONI1<CR> VSMONI2<CR> VSASPNRM<CR> VSASPFUL<CR> VSSC48P<CR> VSSC10I<CR> VSSC72P<CR> VSSC10P<CR> VSSCAUTO<CR>

- 31 -

EVENT PS
PARAMETER TONE DEFEAT ON TONE DEFEAT OFF SB:MTRX ON SB:NON MTRX SB:PL2xC SB:PL2xM SB:ON SB:OFF SB:ESDSCRT SB:ESMTRX CINEMA EQ.ON CINEMA EQ.OFF MODE:CINEMA MODE:MUSIC MODE:GAME MODE:PRO LOGIC ROOM EQ:AUDYSSEY ROOM EQ:BYP.LR ROOM EQ:FLAT ROOM EQ:MANUAL ROOM EQ:OFF BAS ** TRE **

function TONE DEFEAT ON/OFF change SURROUND BACK MODE change
CINEMA EQ. ON/OFF Change CINEMA / MUSIC / GAME / PL mode change
ROOM EQ mode direct change
BASS change TREBLE change
example PSTONE DEFEAT ON<CR> PSTONE DEFEAT OFF<CR> PSSB:MTRX ON<CR> PSSB:NON MTRX<CR> PSSB:PL2X CINEMA<CR> PSSB:PL2X MUSIC<CR> PSSB:ON<CR> PSSB:OFF<CR> PSSB:ESDSCRT<CR> PSSB:ESMTRX<CR> PSCINEMA EQ.ON<CR> PSCINEMA EQ.OFF<CR> PSMODE:CINEMA<CR> PSMODE:MUSIC<CR> PSMODE:GAME<CR> PSMODE:PRO LOGIC<CR> PSROOM EQ:AUDYSSEY<CR> PSROOM EQ:BYP.LR<CR> PSROOM EQ:FLAT<CR> PSROOM EQ:MANUAL<CR> PSROOM EQ:OFF<CR> PSBAS 00<CR> PSTRE 00<CR>

- 32 -

EVENT PS DRC DRC DRC DRC DRC DCO DCO DCO DCO DCO LFE EFF EFF EFF DEL AFD AFD PAN PAN DIM CEN CEI ATT ATT SWR SWR RSZ RSZ RSZ RSZ RSZ
PARAMETER AUTO LOW MID HI OFF OFF MID LOW MID HIGH ** ON OFF ** *** ON OFF ON OFF ** ** ** ON OFF ON OFF S MS M ML L
function DRC change PSDRC PSDRC PSDRC PSDRC PSDRC PSDCO PSDCO PSDCO PSDCO PSDCO PSLFE PSEFF PSEFF PSEFF PSDEL PSAFD PSAFD PSPAN PSPAN PSDIM PSCEN PSCEI PSATT PSATT PSSWR PSSWR PSRSZ PSRSZ PSRSZ PSRSZ PSRSZ

D.COMP change

LFE change EFFECT change EFFECT LEVEL change DELAY change AFDM change PANORAMA change DIMMENSION change CENTER WIDTH change CENTER IMAGE change SW ATT change SW ON/OFF change ROOM SIZE change
example AUTO<CR> LOW<CR> MID<CR> HI<CR> OFF<CR> OFF<CR> MID<CR> LOW<CR> MID<CR> HIGH<CR> 10<CR> UP<CR> DOWN<CR> **<CR> ***<CR> ON<CR> OFF<CR> ON<CR> OFF<CR> **<CR> 07<CR> 10<CR> ON<CR> OFF<CR> ON<CR> OFF<CR> S<CR> MS<CR> M<CR> ML<CR> L<CR>

- 33 -

PARAMETER DELAY *** NIGHT OFF NIGHT LOW NIGHT MID NIGHT HI RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 CN ** BR ** CM ** HUE **
function AUDIO DELAY change, ***:000 to 999 by ASCII ---AVR-3808200=200msMAX 100=100ms, 000=0ms NIGHT MODE change
example PSDELAY 200<CR> PSNIGHT OFF<CR> PSNIGHT LOW<CR> PSNIGHT MID<CR> PSNIGHT HI<CR> PSRSTR OFF<CR> PSRSTR MODE1<CR> PSRSTR MODE2<CR> PSRSTR MODE3<CR> PVCN 06<CR> PVBR 12<CR> PVCM 06<CR> PVHUE 06<CR>

EVENT TF TP XM PARAMETER XM*** (3 digits) XM**(PRESET No.) CH NAME ******** (8 digit) ARTIST **************** (16 digit) TITLE **************** (16 digit) XMID ******** (8 digit) SIGNAL GOOD SIGNAL WEAK SIGNAL MARGINAL SIGNAL NOSIGNAL function --- ***:XM CH No. XM PRESET change to No.** XM CH NAME change XM ARTIST NAME change XM TITLE NAME change XM RADIO ID(XM000 Selected) XM ANTENNA SIGNAL STATUS change example TFXM001<CR> (XM001 CH) TPXMA1<CR> (PRESET No.A1) TMCH NAME 20 on 20<CR> TMARTIST EMINEM TMTITLE JUST LOSE IT TMXMID J3JU703B<CR> TMSIGNAL TMSIGNAL TMSIGNAL TMSIGNAL GOOD<CR> WEAK<CR> MARGINAL<CR> NOSIGNAL<CR> <CR> <CR>

- 37 -

EVENT NSA 8 PARAMETER function Onscreen Display Information is Answered By the NSA Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information Display Line10 Information
NSA0**************_?????<CR> NSA1************_?????<CR> NSA2************_?????<CR> NSA3************_?????<CR> NSA4************_?????<CR> NSA5************_?????<CR> NSA6************_?????<CR> NSA7**************_?????<CR> NSA8**************_?????<CR> *:Character Length MAX96 _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor&Playable Music Infomation Data(1Byte) Bit1:Playable Music =1 Bit2,3:Don't Care Bit4:CURSOR SELECT=1 Bit5,6,7,8:Don't Care <example> NSA0Now Playing USB_????<CR> NSA1Come Away With Me_???<CR> NSA2Norah Jones_?????????<CR> NSA3_????????????????????<CR> NSA4_????????????????????<CR> NSA500:11 100%_???????<CR> NSA6_????????????????????<CR> NSA7_????????????????????<CR> NSA8_????????????????????<CR>

- 38 -

EVENT NSE 8

PARAMETER

function Onscreen Display Information(mserver/iRadio) is Answered By the NSE Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information Display Line10 Information

NSE0**************_?????<CR> NSE1************_?????<CR> NSE2************_?????<CR> NSE3************_?????<CR> NSE4************_?????<CR> NSE5************_?????<CR> NSE6************_?????<CR> NSE7**************_?????<CR> NSE8**************_?????<CR> *:UTF-8 CODE Character(MAX95byte) _:Null ?: Don't Care (The character after Null should be disregarded) :Cursor&Playable Music Information Data(1Byte) Bit1:Playable Music =1 Bit2,3:Don't Care Bit4:CURSOR SELECT=1 Bit5,6,7,8:Don't Care ************_?????:96byte Fixed <example> NSE0Now Playing USB_????<CR> NSE1Come Away With Me_???<CR> NSE2Norah Jones_?????????<CR> NSE3_????????????????????<CR> NSE4_????????????????????<CR> NSE500:11 100%_???????<CR> NSE6_????????????????????<CR> NSE7_????????????????????<CR> NSE8_????????????????????<CR>

- 39 -

EVENT IPA PARAMETER function Onscreen Display Information is Answered By the IPA Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information Display Line10 Information Display Line11 Information
IPA0***************_???<CR> IPA1*************_???<CR> IPA2*************_???<CR> IPA3*************_???<CR> IPA4*************_???<CR> IPA5*************_???<CR> IPA6*************_???<CR> IPA7*************_???<CR> IPA8#**************_???<CR> IPA9***************_???<CR> *:Character Length MAX96 _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor Infomation Data(1Byte) Bit1:Playable Music=1 Bit2:Display Only=1 Bit3:Don't Care Bit4:CURSOR SELECT=1 Bit5,6,7,8:Don't Care #Bit1-8:Dont Care

- 40 -

EVENT IPA
function <example1> IPA0Artist??????????????????<CR> IPA1 Ana Caram_????????????<CR> IPA2 Badi Assad_???????????<CR> IPA3 Christy Baron_????????<CR> IPA4 Marta Gomez_??????????<CR> IPA5 Rebecca Pidgeon_??????<CR> IPA6 Sara K_???????????????<CR> IPA7 Valerie Joyce_????????<CR> IPA8# SFL Songs RPT All_???<CR> IPA9 [ 2/ 6]_?????????<CR> <example2> IPA0Now Playing iPod_???????<CR> IPA1 A HARD DAY'S NIGHT._??<CR> IPA2 /The Beatles_?????????<CR> IPA3_??????????????????????<CR> IPA4 A HARD DAY'S NIGHT_???<CR> IPA5 00:04_??????????????<CR> IPA6_??????????????????????<CR> IPA7_??????????????????????<CR> IPA8# SFL Songs RPT All_???<CR> IPA9????????????????????????<CR>

- 41 -

EVENT IPE 8 9
function Onscreen Display Information(iPod) is Answered By the IPA Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information Display Line10 Information Display Line11 Information

IPE0***************_???<CR> IPE1*************_???<CR> IPE2*************_???<CR> IPE3*************_???<CR> IPE4*************_???<CR> IPE5*************_???<CR> IPE6*************_???<CR> IPE7*************_???<CR> IPE8#**************_???<CR> IPE9***************_???<CR> *:UTF-8 CODE Character(MAX95byte) _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor Information Data(1Byte) Bit1:Playable Music=1 Bit2:Display Only=1 Bit3:Don't Care Bit4:CURSOR SELECT=1 Bit5-8:Don't Care #Bit1-8:Dont Care

- 42 -

EVENT IPE
function <example1> IPE0Artist??????????????????<CR> IPE1 Ana Caram_????????????<CR> IPE2 Badi Assad_???????????<CR> IPE3 Christy Baron_????????<CR> IPE4 Marta Gomez_??????????<CR> IPE5 Rebecca Pidgeon_??????<CR> IPE6 Sara K_???????????????<CR> IPE7 Valerie Joyce_????????<CR> IPE8# SFL Songs RPT All_???<CR> IPE9 [ 2/ 6]_?????????<CR> <example2> IPE0Now Playing iPod_???????<CR> IPE1 A HARD DAY'S NIGHT._??<CR> IPE2 /The Beatles_?????????<CR> IPE3_??????????????????????<CR> IPE4 A HARD DAY'S NIGHT_???<CR> IPE5 00:04_??????????????<CR> IPE6_??????????????????????<CR> IPE7_??????????????????????<CR> IPE8# SFL Songs RPT All_???<CR> IPE9_??????????????????????<CR>

- 43 -

EVENT SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF example SYREMOTE LOCK ON<CR> SYREMOTE LOCK OFF<CR> SYPANEL LOCK ON<CR> SYPANEL+V LOCK ON<CR> SYPANEL LOCK OFF<CR>

- 44 -

DENON AVR control protocol

Ver. 6.2.0

Application model : AVR-2809/AVR-989/AVC-2809 Revision: 6.2.0 Application terminal: RS-232C

Connector specification

. RS-232C Connector type: DB-9pin female type, slave straight connection (DCE type) ( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC ) Communication format: Synchronous system : Asynchronous Communication system : A half duplex Communication speed : 9600bps Character length : 8 bits Parity control : None Start bit : 1 bit Stop bit : 1 bit Communication procedure : Non procedural Communication data length : 135 bytes (maximum)
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT. RESPONSE : The message sent to a controller (Touch Panel etc.) from a system (AVR) if the request command (COMMAND+?+CR(0x0D)) has came from a controller. The RESPONSE should be sent within 200ms of receiving the COMMAND. *The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification: The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs, AND carriage return (0x0D) --- It is used only as a pause sign.
Command structure: COMMAND + PARAMETER + CR (0x0D)
COMMAND: ASCII CODE of 2 characters Ex. SI : Select Input source MS : surround Mode Setting MV : Master Volume setting PW : system Power setting PARAMETER : ASCII CODE ( up to 25 characters) ex. DVD : function name SUPER STADIUM : surround mode name *Special Parameter--- ? : for request command

The example of a command

* <CR> is the meaning of 0x0D. SIDVD<CR> : Select Input source DVD MSSTEREO<CR> : surround Mode Set to STEREO MVUP<CR> : Master Volume UP PWON<CR> : system PoWer ON PWSTANDBY<CR> : system PoWer STANDBY SI?<CR> : Request command for now playing input source >> Return RESPONSE SI***<CR>

Others

A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50". D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel volume of all channels , It described in B) ) returns as EVENT. E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME does NOT return. F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return. G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned. H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to the another request commands(ex. SV command). I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines 99. J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three ASCII characters as bellows. Ex. MASTER VOLUME = +1.0dB : MV81<CR> +0.5dB : MV805<CR> 0dB : MV80<CR> -0.5dB : MV795<CR> -1.0dB : MV79<CR> | | -79.5dB : MV005<CR> -80.0dB : MV00<CR> --: MV99<CR> * At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual. K) 1 seconds later, please transmit the next COMMAND after transmitting a power on COMMANDPWON.
COMMAND and PARAMETER list
PARAMETER function example ON PWON<CR> POWER ON/STANDBY change STANDBY PWSTANDBY<CR> ? PW?<CR> Return PW Status MV UP MVUP<CR> MASTER VOLUME UP/DOWN , direct change to **dB DOWN MVDOWN<CR> ** MV80<CR> **:00 to 99 by ASCII , 80=0dB, 99=---(MIN) ? MV?<CR> Return MV Status CV FL UP CVFL UP<CR> CHANNEL VOLUME UP/DOWN , direct change to **dB FL DOWN CVFL DOWN<CR> ---FRONT Lch FL ** CVFL 50<CR> **:38 to 62 by ASCII , 50=0dB FR UP CVFR UP<CR> FR DOWN CVFR DOWN<CR> ---FRONT Rch FR ** CVFR 50<CR> **:38 to 62 by ASCII , 50=0dB C UP CVC UP<CR> C DOWN CVC DOWN<CR> ---CENTERch C ** CVC 50<CR> **:38 to 62 by ASCII , 50=0dB SW UP CVSW UP<CR> SW DOWN CVSW DOWN<CR> ---SUBWOOFERch SW ** CVSW 50<CR> **:00,38 to 62 by ASCII , 50=0dB,00=OFF SL UP CVSL UP<CR> SL DOWN CVSL DOWN<CR> ---SURROUND Lch SL ** CVSL 50<CR> **:38 to 62 by ASCII , 50=0dB SR UP CVSR UP<CR> SR DOWN CVSR DOWN<CR> ---SURROUND Rch SR ** CVSR 50<CR> **:38 to 62 by ASCII , 50=0dB SBL UP CVSBL UP<CR> ---SURROUND BACK Lch (SBch 2SP) SBL DOWN CVSBL DOWN<CR> SBL ** CVSBL 50<CR> **:38 to 62 by ASCII , 50=0dB SBR UP CVSBR UP<CR> ---SURROUND BACK Rch (SBch 2SP) SBR DOWN CVSBR DOWN<CR> SBR ** CVSBR 50<CR> **:38 to 62 by ASCII , 50=0dB MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section) PW -5COMMAND

PARAMETER function SB UP ---SURROUND BACK ch (SB ch 1SP) SB DOWN SB ** **:00 to 99 by ASCII , 50=0dB ? Return CV Status MU ON OUTPUT MUTE ON/OFF change OFF ? Return MU Status SI PHONO Select INPUT source CD TUNER DVD HDP TV/CBL SAT VCR DVR V.AUX XM (North America model Only) SIRIUS (North America model Only) IPOD ? Return SI Status ZM ON MAIN-ZONE ON/OFF change OFF ? Return ZM Status SR PHONO REC SELECT mode set , and select source | ---The name of PARAMETER is IPOD the same as that of the time of SI COMMAND. SOURCE REC SELECT mode cancel ? Return SR Status CV COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) CV

COMMAND

example CVSB UP<CR> CVSB DOWN<CR> CVSB 50<CR> CV?<CR> MUON<CR> MUOFF<CR> MU?<CR> SIPHONO<CR> SICD<CR> SITUNER<CR> SIDVD<CR> SIHDP<CR> SITV/CBL<CR> SISAT<CR> SIVCR<CR> SIDVR<CR> SIV.AUX<CR> SIXM<CR> SISIRIUS<CR> SIIPOD<CR> SI?<CR> ZMON<CR> ZMOFF<CR> ZM?<CR> SRPHONO<CR> | SRIPOD<CR> SRSOURCE<CR> SR?<CR>

COMMAND SD

PARAMETER AUTO HDMI DIGITAL ANALOG EXT.IN-1 ? AUTO PCM DTS ? DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE ? DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND NEURAL WIDE SCREEN 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB
function set AUTO mode (Priority :HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical ,Coaxial)mode set force ANALOG INPUT mode Set EXT.IN mode Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set , and select source
VIDEO SELECT mode cancel Return SV Status Select SURROUND mode
---North America Model Only
example SDAUTO<CR> SDHDMI<CR> SDDIGITAL<CR> SDANALOG<CR> SDEXT.IN-1<CR> SD?<CR> DCAUTO<CR> DCPCM<CR> DCDTS<CR> DC? SVDVD<CR> SVVDP<CR> SVTV/CBL<CR> SVSAT<CR> SVVCR<CR> SVDVR<CR> SVV.AUX<CR> SVSOURCE<CR> SV?<CR> MSDIRECT<CR> MSPURE DIRECT<CR> MSSTEREO<CR> MSSTANDARD<CR> MSDOLBY DIGITAL<CR> MSDTS SURROUND<CR> MSNEURAL<CR> MSWIDE SCREEN MS7CH STEREO<CR> MSSUPER STADIUM<CR> MSROCK ARENA<CR> MSJAZZ CLUB<CR>

COMMAND MS

PARAMETER CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL ? QUICK1 QUICK2 QUICK3 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK ? ASPNRM ASPFUL ASP? SC48P SC10I SC72P SC10P SC AUTO SC?

function

Return MS Status QUICK SELECT 1-3 MODE SELECT QUICK SELECT 1-3 MODE MEMORY Return MSQUICK Status Set Normal mode Set FULL mode Return VSASPECT Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolution to 1080p Set Resolution to AUTO Return VSSC Status
example MSCLASSIC CONCERT<CR> MSMONO MOVIE<CR> MSMATRIX<CR> MSVIDEO GAME<CR> MSVIRTUAL<CR> MS?<CR> MSQUICK1<CR> MSQUICK2<CR> MSQUICK3<CR> MSQUICK1 MEMORY<CR> MSQUICK2 MEMORY<CR> MSQUICK3 MEMORY<CR> MSQUICK ?<CR> VSASPNRM<CR> VSASPFUL<CR> VSASP?<CR> VSSC48P<CR> VSSC10I<CR> VSSC72P<CR> VSSC10P<CR> VSSCAUTO<CR> VSSC?<CR>

COMMAND PS

PARAMETER TONE DEFEAT ON TONE DEFEAT OFF TONE DEFEAT ? SB:MTRX ON SB:PL2xCINEMA SB:PL2xMUSIC SB:ON SB:OFF SB: ? CINEMA EQ.ON CINEMA EQ.OFF CINEMA EQ. ? MODE:MUSIC MODE:CINEMA MODE:GAME MODE:PRO LOGIC MODE: ? ROOM EQ:AUDYSSEY ROOM EQ:BYP.LR ROOM EQ:FLAT ROOM EQ:MANUAL ROOM EQ:OFF ROOM EQ ? DYN ON DYN OFF DYN VOL DYN ? DYNSET NGT DYNSET EVE DYNSET DAY DYNSET ?
example PSTONE DEFEAT ON<CR> PSTONE DEFEAT OFF<CR> PSTONE DEFEAT ?<CR> PSSB:MTRX ON<CR> PSSB:PL2X CINEMA<CR> PSSB:PL2X MUSIC<CR> PSSB:ON<CR> PSSB:OFF<CR> PSSB: ?<CR> Return PSSB: Status PSCINEMA EQ.ON<CR> CINEMA EQ. ON/OFF PSCINEMA EQ.OFF<CR> PSCINEMA EQ. ?<CR> Return PSCINEMA EQ.Status PSMODE:MUSIC<CR> CINEMA / MUSIC / GAME / PL mode change (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.) PSMODE:CINEMA<CR> PSMODE:GAME<CR> ---SB=ONPL2x mode / SB=OFFPL2 mode PSMODE:PRO LOGIC<CR> --- GAME can change DOLBY PL2 & PL2x mode --- PL can change ONLY DOLBY PL2 mode PSMODE: ?<CR> Return PSMODE: Status PSROOM EQ:AUDYSSEY<CR> MultEQ XT mode direct change PSROOM EQ:BYP.LR<CR> PSROOM EQ:FLAT<CR> PSROOM EQ:MANUAL<CR> PSROOM EQ:OFF<CR> PSROOM EQ: ?<CR> Return PSROOM EQ: Status PSDYN ON<CR> DYNAMIC EQ=ON DYNAMIC VOL=OFF PSDYN OFF<CR> DYNAMIC EQ=OFF DYNAMIC VOL=OFF PSDYN VOL<CR> DYNAMIC EQ=ON DYNAMIC VOL=ON PSDYN ?<CR> Return PSDYN: Status PSDYNSET NGT<CR> Dynamic Vol. Setting = Midnight PSDYNSET EVE<CR> Dynamic Vol. Setting = Evening PSDYNSET DAY<CR> Dynamic Vol. Setting = Day PSDYNSET ?<CR> Return PSDYNSET Status -9-
function PARAMETER setting TONE DEFEAT ON/OFF Return PSTONE DEFEAT Status SURROUND BACK SP MODE set
Return PSDCO Status LFE UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 00=0dB, 10=-10dB ---AVR-2809 can be operated from 0 to -10 Return PSLFE Status EFFECT ON/OFF , EFFECT LEVEL direct change to **dB **:00 to 99 by ASCII , 00=0dB, 10=10dB ---AVR-2809 can be operated from 1 to 15 Return PSEFF Status DELAY UP/DOWN , direct change to ***dB ***:000 to 999 by ASCII , 000=0ms, 300=300ms ---AVR-2809 can be operated from 0 to 300 0-60ms:3ms/Step Over 60ms:10ms/Step DEL ? Return PSDEL Status PS COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section) - 10 -

PARAMETER BAS UP BAS DOWN BAS ** BAS ? TRE UP TRE DOWN TRE ** TRE ? DRC AUTO DRC LOW DRC MID DRC HI DRC OFF DRC ? DCO OFF DCO LOW DCO MID DCO HIGH DCO ? LFE UP LFE DOWN LFE ** LFE ? EFF UP EFF DOWN EFF ** EFF ? DEL UP DEL DOWN DEL ***
function BASS UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 50=0dB ---AVR-2809 can be operated from -6 to +6(44 to 56) Return PSBAS Status TREBLE UP/DOWN , direct change to **dB **:00 to 99 by ASCII , 50=0dB ---AVR-2809 can be operated from -6 to +6(44 to 56) Return PSTRE Status DRC direct change
Return PSDRC Status D.COMP direct change
example PSBAS UP<CR> PSBAS DOWN<CR> PSBAS 50<CR> PSBAS ?<CR> PSTRE UP<CR> PSTRE DOWN<CR> PSTRE 50<CR> PSTRE ?<CR> PSDRC AUTO<CR> PSDRC LOW<CR> PSDRC MID<CR> PSDRC HI<CR> PSDRC OFF<CR> PSDRC ?<CR> PSDCO OFF<CR> PSDCO LOW<CR> PSDCO MID<CR> PSDCO HIGH<CR> PSDCO ?<CR> PSLEE UP<CR> PSLFE DOWN<CR> PSLFE 10<CR> PSLFE ? <CR> PSEFF UP<CR> PSEFF DOWN<CR> PSEFF **<CR> PSEFF ?<CR> PSDEL UP<CR> PSDEL DOWN<CR> PSDEL ***<CR> PSDEL ?<CR>
PARAMETER function AFD ON AFDM ON/OFF AFD OFF AFD ? Return PSAFD Status PAN ON PANORAMA ON/OFF PAN OFF PAN ? Return PSPAN Status DIM UP DIMENSION UP/DOWN , direct change to **dB DIM DOWN **:00 to 99 by ASCII , 00=0, DIM ** ---AVR-2809 can be operated from 0 to 6 DIM ? Return PSDIM Status CEN UP CENTER WIDTH UP/DOWN , direct change to **dB CEN DOWN **:00 to 99 by ASCII , 00=0 CEN ** ---AVR-2809 can be operated from 0 to 7 CEN ? Return PSCEN Status CEI UP CENTER IMAGE UP/DOWN , direct change to **dB CEI DOWN **:00 to 99 by ASCII , 00=0.0 CEI ** ---AVR-2809 can be operated from 0.0 to 1.0 CEI? Return PSCEI Status ATT ON SW ATT ON/OFF ATT OFF ATT ? Return PSATT Status SWR ON SW ON/OFF SWR OFF SWR ? Return PSSWR Status RSZ S ROOM SIZE direct change RSZ MS RSZ M RSZ ML RSZ L RSZ ? Return PSRSZ Status PS COMMAND : "*" parameter uses two or three ASCII characters. (see page4 J) section)
example PSAFD ON<CR> PSAFD OFF<CR> PSAFD ?<CR> PSPAN ON<CR> PSPAN OFF<CR> PSPAN ?<CR> PSDIM UP<CR> PSDIM DOWN<CR> PSDIM **<CR> PSDIM ?<CR> PSCEN UP<CR> PSCEN DOWN<CR> PSCEN 07<CR> PSCEN ?<CR> PSCEI UP<CR> PSCEI DOWN<CR> PSCEI 10<CR> PSCEI ?<CR> PSATT ON<CR> PSATT OFF<CR> PSATT ?<CR> PSSWR ON<CR> PSSWR OFF<CR> PSSWR ?<CR> PSRSZ S<CR> PSRSZ MS<CR> PSRSZ M<CR> PSRSZ ML<CR> PSRSZ L<CR> PSRSZ ?<CR>

- 11 -

PARAMETER function DELAY UP AUDIO DELAY UP/DOWN , direct change to ***dB DELAY DOWN ***:000 to 999 by ASCII , 000=0ms, 200=200ms DELAY *** ---AVR-2809 can be operated from 0 to 200 DELAY ? Return PSDELAY Status NIGHT OFF NIGHT MODE direct change NIGHT LOW NIGHT MID NIGHT HI NIGHT ? Return PSNIGHT Status RSTR OFF AUDIO RESTORER direct change RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? Return PSRSTR Status FRONT SPA FRONT SPEAKER direct change FRONT SPB FRONT A+B FRONT? Return PSFRONT Status PS COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section)

example UP<CR> DOWN<CR> 00<CR> ?<CR> UP<CR> DOWN<CR> 00<CR> ?<CR>

- 14 -

PARAMETER PHONO | IPOD SOURCE UP DOWN ** ON OFF ? Z3MU ON OFF ? Z3CS ST MONO ? Z3CV FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? Z3HPF ON 3 OFF ? COMMAND : "*" parameter uses two Z3 COMMAND Invalid at AVR-989 Z3 Z
function ZONE3 mode set , and select source at AVR-2809 ---The name of PARAMETER is the same as that of the time of SI COMMAND. ZONE3 mode cancel ZONE3 VOLUME UP/DOWN , direct change to **dB **:10 to 99 by ASCII , 80=0dB, 99=---(MIN) ZONE3 ON/OFF change at AVR-2809 Return Z3 Status ZONE3 OUTPUT MUTE ON/OFF change Return Z3MU Status ZONE3 Channel setting Return Z3CS Status ZONE3 CHANNEL VOLUME ---FRONT Lch **:38 to 62 by ASCII ZONE3 CHANNEL VOLUME ---FRONT Rch **:38 to 62 by ASCII Return Z3CV Status ZONE3 HPF ON/OFF UP/DOWN , direct change to **dB , 50=0dB UP/DOWN , direct change to **dB , 50=0dB
Return Z3HPF Status ASCII characters. (see page4 J) section)
example Z3PHONO<CR> | Z3IPOD<CR> Z3SOURCE<CR> Z3UP<CR> Z3DOWN<CR> Z380<CR> Z3ON<CR> Z3OFF<CR> Z2?<CR> Z3MUON<CR> Z3MUOFF<CR> Z3MU?<CR> Z3CSST Z3CSMONO Z3CS? Z3CVFL UP<CR> Z3CVFL DOWN<CR> Z3CVFL 50<CR> Z3CVFR UP<CR> Z3CVFR DOWN<CR> Z3CVFR 50<CR> Z3CV?<CR> Z3HPFON<CR> Z3HPFOFF<CR> Z3HPF?<CR>

- 15 -

COMMAND Z3PS Z
BAS BAS BAS BAS TRE TRE TRE TRE
PARAMETER UP DOWN ** ? UP DOWN ** ?
function Z3PSBAS ZONE3 BASS UP/DOWN , direct change to **dB Z3PSBAS **:00 to 99 by ASCII , 00=0dB ---AVR-2809 can be operated from -10 to +10(40 to 60) Z3PSBAS Z3PSBAS Return Z3PSBAS Status Z3PSTRE ZONE3 TREBLE UP/DOWN , direct change to **dB Z3PSTRE **:00 to 99 by ASCII , 00=0dB ---AVR-2809 can be operated from -10 to +10(40 to 60) Z3PSTRE Z3PSTRE Return Z3PSTRE Status
COMMAND : "*" parameter uses two ASCII characters. (see page4 J) section) Z3 COMMAND Invalid at AVR-989

- 16 -

ANALOG TUNER ControlAVR Model Only COMMAND TF PARAMETER ANUP ANDOWN AN****** (6 digits) AN? ANUP ANDOWN AN** (PRESET No.) AN? ANMEM ANAM ANFM AN? ANAUTO ANMANUAL function TUNER Frequency UP/DOWN --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.) Return TFAN Status TUNER PRESET CH UP/DOWN , --- direct change to No.** Return TPAN Status TUNER PRESET MEMORY TUNER BAND , MODE Select ---Band set to AM ---Band set to FM Return TMAN Status ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode example TFANUP<CR> TFANDOWN<CR> TFAN105000<CR> (1050.00kHz at AM) TFAN?<CR> TPANUP<CR> TPANDOWN<CR> TPANA1<CR> (PRESET No.A1) TPAN?<CR> TPANMEM<CR> TMANAM<CR> TMANFM<CR> TMAN?<CR> TMANAUTO<CR> TMANMANUAL<CR>

- 17 -

XM Control(North America model only)
COMMAND TF PARAMETER XMUP XMDOWN XM*** (3 digits) XM? XMUP XMDOWN XM**(PRESET No.) XM? XMMEM ? function XM Channel UP/DOWN --- ***:XM CH No. Return TFXM Status XM PRESET CH UP/DOWN , direct change to No.** example TFXMUP<CR> TFXMDOWN<CR> TFXM001<CR> (XM001 CH at XM) TFXM?<CR> TPXMUP<CR> TPXMDOWN<CR> TPXMA1<CR> (PRESET No.A1) TPXM?<CR> TPXMMEM<CR> XM?<CR>
Return TPXM Status XM PRESET MEMORY Return XM Status - CHANNEL NAME, ARTIST, TITLE, SIGNAL LEVEL

- 18 -

SIRIUS Control(North America model only)
COMMAND TF PARAMETER STUP STDOWN ST*** (3 digits) STPL**** (4 digits) ST? STUP STDOWN ST**(PRESET No.) ST? STMEM ? function SIRIUS Channel UP/DOWN --- ***:ST CH No. --- ***:Parental Lock Code Number Return TFST Status SIRIUS PRESET CH UP/DOWN , direct change to No.** example TFSTUP<CR> TFSTDOWN<CR> TFST001<CR> (ST001 CH at SIRIUS TUNER) TFSTPL1234<CR> (Parental Lock code 1234 TFST?<CR> TPSTUP<CR> TPSTDOWN<CR> TPSTA1<CR> (PRESET No.A1) TPST?<CR> TPSTMEM<CR> ST?<CR>
Return TPST Status SIRIUS PRESET MEMORY Return ST Status - CHANNEL NAME, ARTIST, COMPOSER,TITLE, SIGNAL LEVEL

- 19 -

iPod Extended Control
COMMAND IP 94 9A 9C 9D 9E 9F 9G 9H 9I 9J 9K 9L 9M 9N 9P 9Q 9X 9Y PARAMETER function Cursor Up Control Cursor Down Control Cursor Left Control Cursor Right Control Enter (Play/Pause) Control Play/Pause Control Stop Control Skip Plus Control Skip Minus Control Manual Search Plus Control(ASD-1R Only) Manual Search Minus Control(ASD-1R Only) Repeat One Control Repeat All Control Repeat Off Control Shuffle Songs Control Shuffle Album Control Shuffle Off Control MENU Control Switch the Browse Mode Control(ASD-1R Only) Switch the Remote Mode Control(ASD-1R Only) Page Up Control Page Down Control Return Onscreen Display Information List (ASCII CODE Character) Request Onscreen Display Information List(iPOD) (UTF-8 CODE Character ) example IP90<CR> IP91<CR> IP92<CR> IP93<CR> IP94<CR> IP9A<CR> IP9C<CR> IP9D<CR> IP9E<CR> IP9F<CR> IP9G<CR> IP9H<CR> IP9I<CR> IP9J<CR> IP9K<CR> IP9L<CR> IP9M<CR> IP9N<CR> IP9P<CR> IP9Q<CR> IP9X<CR> IP9Y<CR> IPA<CR> (Return IPA0-IPA9) Refer to Page 34 IPE<CR> (Return IPE0-IPE9. Refer to Page 37

- 20 -

Cursor/Enter/Menu(Setup)
COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN MEN ON MEN OFF Cursor Up Control Cursor Down Control Cursor Left Control Cursor Right Control Enter Control RETURN Control OSD Menu ON Control OSD Menu OFF Control function example MNCUP<CR> MNCDN<CR> MNCLT<CR> MNCRT<CR> MNENT<CR> MNRTN<CR> MNMEN ON<CR> MNMEN OFF<CR>

Remote Lock/Panel Lock

COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF REMOTE LOCK ? PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF PANEL LOCK ? function REMOTE CONTROL LOCK ON/OFF Return SYREMOTE LOCK Status PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF Return SYPANEL LOCK Status example SYREMOTE LOCK ON<CR> SYREMOTE LOCK OFF<CR> SYREMOTE LOCK ?<CR> SYPANEL LOCK ON<CR> SYPANEL+V LOCK ON<CR> SYPANEL LOCK OFF<CR> SYPANEL LOCK ?<CR>

- 21 -

EVENT(or RESPONSE) and PARAMETER list
EVENT PW MV PARAMETER ON STANDBY ** function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 00 = -80dB 99 = ---(MIN) CHANNEL VOLUME change , **:00,38 to 62 by ASCII 62 = +12dB(MAX) 50 = 0dB 38 = -12dB(MIN) 00 = OFF (define ONLY Subwoofer ch in DIRECT mode.) (at SB ch (at SB ch (at SB ch OUTPUT MUTE 2SP) 2SP) 1SP) ON/OFF change example PWON<CR> PWSTANDBY<CR> MV80<CR>
FL ** FR ** C ** SW ** SL ** SR ** SBL ** SBR ** SB ** ON OFF PHONO CD TUNER DVD HDP TV/CBL SAT VCR DVR V.AUX

INPUT source change

CVFL 50<CR> CVFR 50<CR> CVC 50<CR> CVSW 50<CR> CVSL 50<CR> CVSR 50<CR> CVSBL 50<CR> CVSBR 50<CR> CVSB 50<CR> MUON<CR> MUOFF<CR> SIPHONO<CR> SICD<CR> SITUNER<CR> SIDVD<CR> SIHDP<CR> SITV/CBL<CR> SISAT<CR> SIVCR<CR> SIDVR<CR> SIV.AUX<CR>
The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page4 J) section)

- 22 -

EVENT SI ZM SR
PARAMETER XM SIRIUS IPOD ON OFF PHONO | IPOD SOURCE AUTO HDMI DIGITAL ANALOG EXT.IN-1 AUTO PCM DTS DVD HDP TV/CBL SAT VCR DVR V.AUX SOURCE

function (North America model Only) (North America model Only) MAIN-ZONE ON/OFF change REC SELECT source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. REC SELECT mode cancel INPUT mode change
---Set EXT.IN mode DIGITAL INPUT mode change VIDEO SELECT mode source change
example SIXM<CR> SISIRIUS<CR> SIIPOD<CR> ZMON<CR> ZMOFF<CR> SRPHONO<CR> | SRIPOD<CR> SRSOURCE<CR> SDAUTO<CR> SDHDMI<CR> SDDIGITAL<CR> SDANALOG<CR> SDEXT.IN-1<CR> DCAUTO<CR> DCPCM<CR> DCDTS<CR> SVDVD<CR> SVVDP<CR> SVTV/CBL<CR> SVSAT<CR> SVVCR<CR> SVDVR<CR> SVV.AUX<CR> SVSOURCE<CR>

- 23 -

EVENT MS
PARAMETER DIRECT SURROUND mode change PURE DIRECT STEREO MULTI CH IN M CH IN+DOLBY EX M CH IN+PL2X C M CH IN+PL2X M MULTI CH DIRECT M CH DRCT+DOLBY EX M CH DRCT+PL2X C M CH DRCT+PL2X M MULTI CH PURE D M CH PURE D +DOLBY EX M CH PURE D+PL2X C M CH PURE D+PL2X M MULTI CH IN 7.1 M DIRECT 7.1 M CH PURE D 7.1 DOLBY PRO LOGIC DOLBY PL2 CINEMA DOLBY PL2 MUSIC DOLBY PL2 G DOLBY PL2X C DOLBY PL2X M DOLBY PL2X G DOLBY DIGITAL DOLBY D EX DOLBY D+PL2X C DOLBY D+PL2X M
example MSDIRECT<CR> MSPURE DIRECT<CR> MSSTEREO<CR> MSMULTI CH IN<CR> MSM CH IN+DOLBY EX<CR> MSM CH IN+PL2X C<CR> MSM CH IN+PL2X M<CR> MSMULTI CH DIRECT<CR> MSM CH DRCT+DOLBY EX <CR> MSM CH DRCT+PL2X C<CR> MSM CH DRCT+PL2X M<CR> MSMULTI CH PURE D<CR> MSM CH PURE D+DOLBY EX<CR> MSM CH PURE D+PL2X C<CR> MSM CH PURE D+PL2X M<CR> MSMULTI CH IN 7.1<CR> MSM DIRECT 7.1<CR> MSM CH PURE D 7.1<CR> MSDOLBY PRO LOGIC<CR> MSDOLBY PL2 C<CR> MSDOLBY PL2 M<CR> MSDOLBY PL2 G<CR> MSDOLBY PL2X C<CR> MSDOLBY PL2X M<CR> MSDOLBY PL2X G<CR> MSDOLBY DIGITAL<CR> MSDOLBY D EX<CR> MSDOLBY D+PL2X C<CR> MSDOLBY D+PL2X M<CR>

- 24 -

PARAMETER DTS NEO:6 C DTS NEO:6 M DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.1 DTS+NEO:6 DTS+PL2X C DTS+PL2X M DTS96/24 DTS96 ES MTRX WIDE SCREEN 5CH STEREO 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL DSD DIRECT DSD PURE DIRECT DSD MULTI DRCT DSD MULTI PURE MPEG2 AAC AAC+DOLBY EX AAC+PL2X C AAC+PL2X M

JAPAN JAPAN JAPAN JAPAN

model model model model

Only Only Only Only

example MSDTS NEO:6 C<CR> MSDTS NEO:6 M<CR> MSDTS SURROUND<CR> MSDTS ES DSCRT6.1<CR> MSDTS ES MTRX6.1<CR> MSDTS+NEO:6<CR> MSDTS+PL2X C<CR> MSDTS+PL2X M<CR> MSDTS96/24<CR> MSDTS96 ES MTRX<CR> MSWIDE SCREEN<CR> MS5CH STEREO<CR> MS7CH STEREO<CR> MSSUPER STADIUM<CR> MSROCK ARENA<CR> MSJAZZ CLUB<CR> MSCLASSIC CONCERT<CR> MSMONO MOVIE<CR> MSMATRIX<CR> MSVIDEO GAME<CR> MSVIRTUAL<CR> MSDSD DIRECT<CR> MSDSD PURE DIRECT<CR> MSDSD MULTI DRCT<CR> MSDSD MULTI PURE<CR> MSMPEG2 AAC<CR> MSAAC+DOLBY EX<CR> MSAAC+PL2X C<CR> MSAAC+PL2X M<CR>

- 25 -

PARAMETER NEURAL DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2x C DOLBY D+ +PL2x M DOLBY HD DOLBY HD+EX DOLBY HD+PL2x C DOLBY HD+PL2x M DTS HD DTS HD MSTR DTS EXPRESS DTS HD+NEO:6 DTS HD+PL2X C DTS HD+PL2X M DTS ES 8CH DSCRT QUICK1 QUICK2 QUICK3 QUICK0 ASPNRM ASPFUL SC48P SC10I SC72P SC10P SCAUTO TONE DEFEAT ON TONE DEFEAT OFF SB:MTRX ON SB:PL2xC SB:PL2xM
example MSNEURAL<CR> MSDOLBY D+<CR> MSDOLBY D+ +EX<CR> MSDOLBY D+ +PL2X C<CR> MSDOLBY D+ +PL2X M<CR> MSDOLBY HD<CR> DOLBY TRUE HD MSDOLBY HD+EX<CR> MSDOLBY HD+PL2X C<CR> MSDOLBY HD+PL2X M<CR> MSDTS HD<CR> MSDTS HD MSTR<CR> MSDTS EXPRESS<CR> MSDTS HD+NEO:6<CR> MSDTS HD+PL2X C<CR> MSDTS HD+PL2X M<CR> MSDTS ES 8CH DSCRT<CR> MSQUICK1<CR> QUICK SELECT mode change MSQUICK2<CR> MSQUICK3<CR> --- QUICK 1 (or QUICK 2 or QUICK 3) Change QUICK OFF MSQUICK0<CR> VSASPNRM<CR> ASPECT setting change VSASPFUL<CR> VSSC48P<CR> SCALER setting change VSSC10I<CR> VSSC72P<CR> VSSC10P<CR> VSSCAUTO<CR> PSTONE DEFEAT ON<CR> TONE DEFEAT ON/OFF change PSTONE DEFEAT OFF<CR> PSSB:MTRX ON<CR> SURROUND BACK MODE change PSSB:PL2X CINEMA<CR> PSSB:PL2X MUSIC<CR>

AUDIO RESTORER change

FRONT SPEAKER change

- 29 -

EVENT Z2
PARAMETER PHONO | IPOD SOURCE **

Z2MU Z2CS

ZONE2 Channel setting ---AVR989:Disable Z2CV **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB Z2HPF ZONE2 HPF ON/OFF change ---AVR989:Disable Z2PS ZONE2 BASS change ---AVR989:Disable TRE ** ZONE2 TEBLE change ---AVR989:Disable The PARAMETER of Z2 EVENT : Uses two ASCII characters. (see page4 J) section)
ON OFF ON OFF ST MONO FL ** FR ** ON OFF BAS **
function ZONE2 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. ZONE2 mode cancel ZONE2 VOLUME change , **:10 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 10 = -70dB 99 = ---(MIN) ZONE2 ON/OFF change ZONE2 OUTPUT MUTE ON/OFF change
example Z2PHONO<CR> | Z2IPOD<CR> Z2SOURCE<CR> Z280<CR>
Z2ON<CR> Z2OFF<CR> Z2MUON<CR> Z2MUOFF<CR> Z2CSST<CR> Z2CSMONO<CR> Z2CVFL 50<CR> Z2CVFR 50<CR> Z2HPFON<CR> Z2HPFOFF<CR> Z2PSBAS 00<CR> Z2PSTRE 00<CR>

- 30 -

function ZONE3 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND. ZONE3 mode cancel ---AVR989:Disable ** ZONE3 VOLUME change , **:10 to 99 by ASCII 98 = +18dB(MAX) 80 = 0dB 10 = -70dB 99 = ---(MIN) ---AVR989:Disable ON ZONE3 ON/OFF change OFF ---AVR989:Disable Z3MU ON ZONE3 OUTPUT MUTE ON/OFF change OFF ---AVR989:Disable Z3CS ST ZONE3 Channel setting MONO ---AVR989:Disable Z3CV FL ** **:38 to 62 by ASCII , 50=0dB ---AVR989:Disable FR ** **:38 to 62 by ASCII , 50=0dB ---AVR989:Disable Z3HPF ON ZONE3 HPF ON/OFF change OFF ---AVR989:Disable Z3PS BAS ** ZONE3 BASS change ---AVR989:Disable TRE ** ZONE3 TEBLE change ---AVR989:Disable The PARAMETER of Z3 EVENT : Uses two ASCII characters. (see page4 J) section) Z3 COMMAND Invalid at AVR-989 Z3
PARAMETER PHONO | IPOD SOURCE
example Z3PHONO<CR> | Z3IPOD<CR> Z3SOURCE<CR> Z380<CR>
Z3ON<CR> Z3OFF<CR> Z3MUON<CR> Z3MUOFF<CR> Z3CSST<CR> Z3CSMONO<CR> Z3CVFL 50<CR> Z3CVFR 50<CR> Z3HPFON<CR> Z3HPFOFF<CR> Z3PSBAS 00<CR> Z3PSTRE 00<CR>

- 31 -

ANALOG TUNER Control EVENT TF PARAMETER AN****** (6 digits) AN**(PRESET No.) ANAM ANFM ANAUTO ANMANUAL function TUNER Frequency change --- ****.** kHz at AM band ****.** MHz at FM band TUNER PRESET change to No.** TUNER BAND , MODE change ---Band set to AM ---Band set to FM ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode example TFAN105000<CR> (1050.00kHz at AM) TPANA1<CR> (PRESET No.A1) TMANAM<CR> TMANFM<CR> TMANAUTO<CR> TMANMANUAL<CR>
EVENT TF TP XM PARAMETER XM*** (3 digits) XM CHECK ANT XM**(PRESET No.) CH NAME ******** (8 digit) ARTIST **************** (16 digit) TITLE **************** (16 digit) XMID ******** (8 digit) SIGNAL GOOD SIGNAL WEAK SIGNAL MARGINAL SIGNAL NOSIGNAL function --- ***:XM CH No. XM TUNER is not connected XM PRESET change to No.** XM CH NAME change XM ARTIST NAME change XM TITLE NAME change XM RADIO ID(XM000 Selected) XM ANTENNA SIGNAL STATUS change example TFXM001<CR> (XM001 CH) TFXM CHECK ANT<CR> TPXMA1<CR> (PRESET No.A1) TMCH NAME 20 on 20<CR> TMARTIST EMINEM**********<CR> TMTITLE JUST LOSE IT****<CR> TMXMID J3JU703B<CR> TMSIGNAL TMSIGNAL TMSIGNAL TMSIGNAL GOOD<CR> WEAK<CR> MARGINAL<CR> NOSIGNAL<CR>

- 32 -

SIRIUS ControlNorth America Model Only
EVENT TF PARAMETER ST*** (3 digits) STPL ON STPL OFF STUL OK STUL NG STCH SUB STCH UNS STMP VAL STMP INV ST CHECK ANT ST** (PRESET No.) CH NAME ******** (8 digits) ARTIST ***************** (36 digits) TITLE ***************** (36 digits) COMPOSER ***************** (36 digits) ID ************ (12 digits) SIGNAL EXCELLENT SIGNAL GOOD SIGNAL WEAK SIGNAL NOSIGNAL --- ***:ST CH No. Parental Lock Status ON Parental Lock Status OFF Unlocking is successful Unlocking is failed Subscribed channel Unsubscribed channel Valid Channel Invalid Channel SIRIUS TUNER is not connected SIRIUS PRESET change to No.** SIRIUS CH NAME change SIRIUS ARTIST NAME change SIRIUS TITLE NAME change SIRIUS COMPOSER NAME change SIRIUS ID(SR000 Selected) SIRIUS ANTENNA SIGNAL STATUS change function example TFST001<CR> (ST001 CH at SIRIUS TUNER) TFSTPL ON<CR> TFSTPL OFF<CR> TFSTUL OK<CR> TFSTUL NG<CR> TFSTCH SUB<CR> TFSTCH UNS<CR> TFSTMP VAL<CR> TFSTMP INV<CR> TFST CHECK ANT<CR> TPSTA1<CR> (PRESET No.A1) STCH NAME Hit song<CR> STARTIST Elvis Presley*** ********************<CR> STTITLE I'm Leaving***** ********************<CR> STCOMPOSER MUSIC*********** ********************<CR> STID 123456789012<CR> STSIGNAL STSIGNAL STSIGNAL STSIGNAL EXCELLENT<CR> GOOD<CR> WEAK<CR> NOSIGNAL<CR>

- 33 -

EVENT IPA PARAMETER function Onscreen Display Information(iPod) is Answered By the IPA Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information ---ASD-3N/3W Connect Display Information is blank Display Line10 Information Display Line11 Information example
IPA0***************_???<CR> IPA1*************_???<CR> IPA2*************_???<CR> IPA3*************_???<CR> IPA4*************_???<CR> IPA5*************_???<CR> IPA6*************_???<CR> IPA7*************_???<CR> IPA8#**************_???<CR> IPA9***************_???<CR> *:Character Length MAX96 _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor Information Data(1Byte) Bit1:Playable Music=1 Bit2:Display Only=1 Bit3:Don't Care Bit4:CURSOR SELECT=1 Bit5-8:Don't Care #iPod dock Information Data(1Byte) Bit1Unknown=1 Bit2:ASD-1R=1 Bit3:ASD-3N/3W=1 Bit4-8:Dont Care

- 34 -

EVENT IPA

PARAMETER

example <example1-for ASD-1R> IPA0Artist??????????????????<CR> IPA1 Ana Caram_????????????<CR> IPA2 Badi Assad_???????????<CR> IPA3 Christy Baron_????????<CR> IPA4 Marta Gomez_??????????<CR> IPA5 Rebecca Pidgeon_??????<CR> IPA6 Sara K_???????????????<CR> IPA7 Valerie Joyce_????????<CR> IPA8# SFL Songs RPT All_???<CR> IPA9 [ 2/ 6]_?????????<CR> <example2-for ASD-1R> IPA0Now Playing iPod_???????<CR> IPA1 A HARD DAY'S NIGHT._??<CR> IPA2 /The Beatles_?????????<CR> IPA3_??????????????????????<CR> IPA4 A HARD DAY'S NIGHT_???<CR> IPA5 00:04_??????????????<CR> IPA6_??????????????????????<CR> IPA7_??????????????????????<CR> IPA8# SFL Songs RPT All_???<CR> IPA9_????????????????????????<CR>

- 35 -

example <example1-for ASD-3N/W> IPA0Artist??????????????????<CR> IPA1Ana Caram_????????????<CR> IPA2Badi Assad_???????????<CR> IPA3Christy Baron_????????<CR> IPA4Marta Gomez_??????????<CR> IPA5Rebecca Pidgeon_??????<CR> IPA6Sara K_???????????????<CR> IPA7_?????????????????????<CR> IPE8# SFL On RPT All_???<CR> IPA9 [ 2/ 6]_?????????<CR> <example2-for ASD-3N/W> IPA0Now Playing iPod_???????<CR> IPA1 A HARD DAY'S NIGHT._??<CR> IPA2 /The Beatles_?????????<CR> IPA3_??????????????????????<CR> IPA4 A HARD DAY'S NIGHT_???<CR> IPA5 00:04_??????????????<CR> IPA6_??????????????????????<CR> IPA7_??????????????????????<CR> IPE8# SFL On RPT All_???<CR> IPA9_???????????????????????<CR>

- 36 -

EVENT IPE 8 9
function Onscreen Display Information(iPod) is Answered By the IPE Command. Display Line1 Information Display Line3 Information Display Line4 Information Display Line5 Information Display Line6 Information Display Line7 Information Display Line8 Information Display Line9 Information ---ASD-3N/3W Connect Display Information is blank Display Line10 Information Display Line11 Information

example

IPE0***************_???<CR> IPE1*************_???<CR> IPE2*************_???<CR> IPE3*************_???<CR> IPE4*************_???<CR> IPE5*************_???<CR> IPE6*************_???<CR> IPE7*************_???<CR> IPE8#**************_???<CR> IPE9***************_???<CR> *:UTF-8 CODE Character(MAX95byte) _:Null ?:Exclusion(The character after Null should be disregarded) :Cursor Information Data(1Byte) Bit1:Playable Music=1 Bit2:Display Only=1 Bit3:Don't Care Bit4:CURSOR SELECT=1 Bit5-8:Don't Care #iPod dock Information Data(1Byte) Bit1Unknown=1 Bit2:ASD-1R=1 Bit3:ASD-3N/3W=1 Bit4-8:Dont Care ************_?????:96byte Fixed

- 37 -

EVENT IPE
example <example1-for ASD-1R> IPE0Artist??????????????????<CR> IPE1 Ana Caram_????????????<CR> IPE2 Badi Assad_???????????<CR> IPE3 Christy Baron_????????<CR> IPE4 Marta Gomez_??????????<CR> IPE5 Rebecca Pidgeon_??????<CR> IPE6 Sara K_???????????????<CR> IPE7 Valerie Joyce_????????<CR> IPE8# SFL Songs RPT All_???<CR> IPE9 [ 2/ 6]_?????????<CR> <example2-for ASD-1R> IPE0Now Playing iPod_???????<CR> IPE1 A HARD DAY'S NIGHT._??<CR> IPE2 /The Beatles_?????????<CR> IPE3_??????????????????????<CR> IPE4 A HARD DAY'S NIGHT_???<CR> IPE5 00:04_??????????????<CR> IPE6_??????????????????????<CR> IPE7_??????????????????????<CR> IPE8# SFL Songs RPT All_???<CR> IPE9_??????????????????????<CR>

- 38 -

example <example1-for ASD-3N/R> IPE0Artist??????????????????<CR> IPE1 Ana Caram_????????????<CR> IPE2 Badi Assad_???????????<CR> IPE3 Christy Baron_????????<CR> IPE4 Marta Gomez_??????????<CR> IPE5 Rebecca Pidgeon_??????<CR> IPE6 Sara K_???????????????<CR> IPE7_?????????????????????<CR> IPE8# SFL On RPT All_???<CR> IPE9 [ 2/ 6]_?????????<CR> <example2-for ASD-3N/R> IPE0Now Playing iPod_???????<CR> IPE1 A HARD DAY'S NIGHT._??<CR> IPE2 /The Beatles_?????????<CR> IPE3_??????????????????????<CR> IPE4 A HARD DAY'S NIGHT_???<CR> IPE5 00:04_??????????????<CR> IPE6_??????????????????????<CR> IPE7_??????????????????????<CR> IPE8# SFL On RPT All_???<CR> IPE9_??????????????????????<CR>