AVR-4308CI / 3808CI Firmware Update Instructions

Table of Contents

1. Before Updating - Requirements --------------------------------------------P1 - Recommendations -------------------------------------- P1 - Key Notes on Network Environment Configuraitons - P1 - About System Setup Memory --------------------------P1 - Check Your Firmware Version -------------------------- P2 -------------------------------------------------- P3 ---------------------------------------- P4 ---------------------------------------- P5 - P7 ---------------------------------------- P8

2. Reinitialize

3. Basic Operations 4. Firmware Update 5. Trouble Shooting
6. Getting Upgrade ID # --------------------------------------- P9

10/1/2008

Denon Electronics (USA), LLC.Denon Electronics (USA), LLC.
100 Corporate Drive, Mahwah, New Jersey 07430 USA TEL: 201-762-6500 usa.denon.com

Denon Brand Company

D&M Building, 2-1 Nisshin-cho, Kawasaki-ku, Kawasaki-shi, Kanagawa, 210-8569, Japan

1. Before Updating

Requirements
- Broadband Internet Access - Cable/DSL Modem - Network Router or Hub

AVR-4308CI AVR-3808CI

- Proper configuration of the Denon A/V component to work on a particular Network Environment - Ethernet Straight Cable for Direct connection to the Network Environment

Recommentations

- If you did not install, or configure, the Denon A/V Component with your Network Environment, please contact your Network Installer/Integrator to assist. - If connecting the Denon A/V Component to your Network Environment for the first time, please read the following sections in the Instruction Manual provided with your component.
Network Audio : AVR-3808/4308CI Instruction Manual, page 20 Network Setup : AVR-3808CI Instruction Manual, page 32, AVR-4308CI Instruction Manual, pages 32-34 Denon does not recommend using Wi-Fi network connectivity when updating/upgrading the components. This is due to the higher possibility of errors in the update/upgrade process from decreased, and/or drop outs of Wi-Fi signals as well as interruption from other nearby Wi-Fi, or other Radio Frequency generating devices.
- Connect the Denon A/V Component directly to your Network Environment via an Ethernet Straight Cable.
- Once the Denon A/V Component is connected and configured properly to your Network Environment, please test that you can receive and listen to Internet Radio stations on the Net//USB input.
This will show you have, at a minimum, a good Internet connection to the component.
Be sure not to 'Power Off' the unit during the update/upgrade process as this will cause a failure in the process.
If this does occur and the unit will not respond normally, please contact Denon USA Customer Service at 1-800-497-8921.
Key Notes on Network Environment Configurations
- Denon A/V Components are not compatible with PPPoE (Point to Point Protocol over Ethernet).
Contact you Internet Service Provider (ISP) to assist in procuring a PPPoE Router.
- Denon A/V Components are not UPnP (Universal Plug and Play) compliant.
This could be an issue with some routers on the market (we have seen this on some NetGear products). You can disable UPnP in the routers setup configuration, however changing this setting can affect the normal operation of other devices on your Network. Contact your Router manufacturer for assistance.
- Some Firewall settings in your network router may not permit the Updating/Upgrading functionality of Denon A/V Components. Contact your Router manufacturer for assistance. - Be sure to disable "VPN" on any PC on your network environment. Company or office network connections will cause a failure in the process.
About System Setup Memory
- The Update Firmware will not reset the system setup configurations of your Denon A/V component.
Note that after downloading and installing the Upgrade Feature Pack (from October 1st, 2008), you will need to recalibrate your system using the Audyssey Room EQ in the component. This is required for you to get the best level of performance from the newly added Audyssey features of Dynamic Volume and Dynamic EQ.

Page 1

Check Your Firmware Version
- Press and hold "Status" key and "Return" key, and push "Power Switch" on - Press "Status" key twice, and front display will show "Main XX.XX" version information

Front Display

Power Switch Return Status
- Find your Main Processor version from list below, and go to next step Model AVR-3808CI Main Version Release Month Notes 01.95 01.73 01.69 01.68 01.57 01.28 01.03 Sep, 2008 Jul. 2008 Apr. 2008 Feb. 2008 Nov. 2007 Oct. 2007 Jul. 2007 Need Initialize first, and update Need Update Not necessary update

Page 9

- Getting Upgrade ID #

Page 5-9

- Firmware Update - Getting Upgrade ID #

Page 3-9

- Re-Initialize - Firmware Update - Getting Upgrade ID #

AVR-4308CI

01.95 01.72 01.69 01.57 01.28 AA.44
Sep. 2008 Jul. 2008 Feb. 2008 Nov. 2007 Sep. 2007 Jul. 2007

Not necessary update

Need Update
Need Initialize first, and update

Page 2

2. Re-Initialize

NOTICE

- Re-Initialize BEFORE Update is required only for the following customers AVR-3808CI Main Ver 01.03 AVR-4308CI Main Ver AA.44 - Note re-initialization will erase and reset the component to factory settings - After completion of the update, you will need to redo system settings
Initializing BEFORE Update
- Press and hold "Cursor UP" key and "Cursor DOWN" key, and push "Power Switch" on - Front display will show all indications, and Initialize will complete

Power Switch

Cursor Down

Cursor Up

> Go to Next Page

Page 3

3. Basic Operations

Basic Operations

Menu Icon

Highlight Cursor

Selectable Item

Text guidance

On-Screen Interactive Display
A/V Receiver (shown 4308CI)
'MENU Key' : Show On-Screen Interactive Display 'ENTER Key' : Select 'Cursor Keys' : Move Highlight Cursor
NOTE: Be sure 'AMP key' is flashing, and that the

Front Panel

Remote Control
remote is in "Main Zone" mode, see the following instruction manual section "Remote ControlUnit Operations". AVR-4308CI : page 61 AVR-3808CI : page 59

Page 4

4. Firmware Update (1/3)
(1) Select "Manual Setup"
- Press the Menu key on the remote control or on the Front Panel of the AVR. - Pressing the Down Cursor key, highlight the icon (shown as a pair of pliers, a screwdriver and a wrench) for Manual Setup - Press the Right Cursor key to enter Manual Setup

Front Panel Display

(2) Select "Option Setup"
- Pressing the Down Cursor key, highlight the icon (shown as a briefcase) for Option Setup - Press the Right Cursor key to enter Option Setup

(3) Select "Firmware Update"
- Pressing the Down Cursor key, highlight Firmware Update

Page 5

4. Firmware Update (2/3)
(4) Select "Check for Update"
- Press the Right Cursor key to highlight Check for Update - Press the 'Enter' key to start the "Check for Update"
(5) Checking for Available Firmware
(6) Available Firmware Information
- Press the Enter key to Execute the Update Process

Page 6

4. Firmware Update (3/3)
(7) Confirming to Run Update
- With the "Yes" button highlighted, press the 'Enter' key to execute the update. - If you do not wish to proceed with the update, press the 'Right Cursor' key to highlight the "No" button, then press the 'Enter' key to exit the update procedure.
(8) Start Update / In Progress
- On Screen Interface will show message "Please Wait", and the unit goes into update mode. (On Screen Interface goes off) - The 'Standby' power indicator will go "Red" and the On Screen Interface will turn off. - Update process information can be seen
on the Front Panel Display.
Power indicator will go RED

(9) Update Complete

- Unit will automatically complete process and repower itself 'On'. - The "Standby Power" indicator will turn

"Green".

Power indicator will go Green

Page 7

5. Trouble Shooting
Indication of FL Display Download failed Updating failed Login failed Connection failed Server is busy Regist failed
Update Error Messages and Trouble Shooting Tips
Reason for Failure Countermeasure Update is imperfect or fails Please turn Main power off, then on again, confirm procedure, and perform update again Internet Connection failure Confirm the unit is correctly connected to the Internet. Server is busy Try to update at a later time Failure to Register with the Please turn Main power off, then on again, confirm Server procedure, and perform update again

Support

If you have problem for updating, please contact Denon USA Customer Service
Customer Service hours of operation: 9:00 AM to 5:00 PM ET, M-F

1-800-497-8921

During peak call-in times or for after hours Tech and Operational self help support, please use our online FAQ database.
http://denon.custhelp.com/

Page 8

6. Getting Upgrade ID #

Important Notice

- The "Upgrade ID" number is required for the Upgrade Feature Pack registration. - When registering your Denon A/V Component for the Upgrade Feature Pack online, via the Denon USA web site (www.usa.denon.com), you will need the "Upgrade ID" number which was created by the firmware update released Sep. 2008.

> See Page 2 Check Your Firmware Version
- If you have not performed a firmware update since before that date, you must do so before proceeding further.
> See Page 5 - 7 Update Instructions

Getting Upgrade ID #

- Be sure unit is connected to network properly - Press "ON/STANDBY" button to power on, and indicator will turn to green. *Need few seconds to complete network connection for 3 seconds. *Be sure to select source other than NET/USB characters. - Front display will show 'Upgrade ID' with 12 digit - Press and keep "Status" key and "Right Cursor" key
Front Panel Display (ID shown above is sample)

MEMO : Upgrade ID