ice>Link: Plus Update Guide

1. Update Contents

a. Copy the ice-Link_Plus_fw_xxx.exe self extracting archive into a folder. Start the extraction by double clicking the file. A window, as shown in the image above, will open, showing the extraction process. For Mac ZIP format is also available.
2. Copying the Update Files
a. Connect the iPod to the computer. If you get the message shown above select Cancel or all the information will be permanently deleted from your iPod. This message appears when an iPod is formatted for Mac and is connected to a PC or vice versa.
ice>Link Plus update guide
b. If you are connecting an iPod to a computer that is not the default iTunes music library you will see the warning message shown in the image above. Select NO or all songs will be permanently deleted from the iPod.
c. Open iTunes. Go to Edit > Preferences Click the iPod tab. Make sure you have Manually manage songs and playlists selected as shown in the image above.
d. Open the folder to which the update files were extracted to. From the window containing the update files, DRAG the file named UPDATE.M3U to the location shown in the picture above.
e. A window as shown in the image above, will pop up indicating the playlist copy progress.
A new playlist named UPDATE will appear in iTunes. Select this playlist and then select all of the files within the playlist. DRAG the selected files into the iPod icon as shown in the image above. If the file transfer has been completed, the update files have successfully been copied to the iPod. The iPod may now be disconnected from your computer, and you may proceed to the following steps.

3. The Update Process

Connect the iPod to the ice>Link for the rest of the update process. a.
In the ice>ink menu select ice>Link Setup and then select Update ice>Link. b.
An update found screen will appear as shown in the image above. It will ask for a Load Update confirmation. Select to confirm. c.
A Loading Update screen will appear as shown in the image above. DO NOT DISCONNECT the iPod at this time as it may cause permanent damage to the ice>Link. The update will take about 1 minute on a 4G iPod, while it will take over 3 minutes on a mini iPod. You can continue to listen to your music while updating. You will notice that the track counter goes from 0 to 99 as an indication of the upgrade process. Ice>Link Plus will restart itself a few seconds after reaching 99. d.
When the Update is complete the ice>Link will reboot. Following the directions on the screen (as shown in the picture above), turn the ignition OFF and then ON and select the CD changer source. The update process is now complete.

4. SUPPORT

If you experience any problems while updating, check Knowledge Base at support.dension.com or send email to support@dension.com for technical support (support@densionusa.com for US or Canada).

Installation Guide

for Mercedes
iceLink: Plus for Mercedes - Installation Guide
This instruction is provided for educational purpose only, we are not responsible for any damages ! Always seek professional help when in doubt !
1.Confirm that you have all Dension ice>Link parts and they are compatible with your vehicle and radio system. 2.Make sure to have the radio security code in handy if the vehicle requires code upon loss of power. 3.Follow the hardware installation guides. If radio removal is required, proceed following the factory service guide of the vehicle. 4.Configure the system [see configuration guide] 5.Verify operation 6.Read users manual
Dension ice>Link Plus parts:
iPod side CRADLE or CABLE (only one included):
iPod cradle 3rd and 4th Gen

iPod cradle Mini iPod

Dock cable 3rd, 4th, mini and Photo iPod compatible
Cable Classic and 2nd Gen iPod

Ice>Link adapter

Vehicle Specific Adapter

Adapter side cable

Vehicle side cable
Actual cable will vary depending on application! An extension cable and/or car specific adapter may be part of the package for some kits.
Ice>Link: Plus Connection Diagram
Disconnect the vehicles battery before installation! Also, if present, disconnect factory CD changer permanently!
For vehicles with the glove box designated as the CD changer location, The factory optical cables may be located as shown in the image below.
Use the Chart below to find the location of the factory CD changer harness if a changer is not installed in your vehicle. If a changer is installed, it MUST be permanently disconnected!
For component location call Dension USA or see factory changer install guide.
Mounting the ice>Link: Plus cradle
Assemble the base of the iPod cradle with an optional vehicle specific adapter. Optional adapter is not required, however recommended for easy and damage free installation.
NEVER install any object in the way of airbags! The force of an opening airbag can launch any object in its path with sufficient force to kill someone!
Attach the cradle to the back with at least 2 screws. If holes do not align rotate the base until a match is found.
Insert the front of the cradle to the back piece, but do not force the cradle onto the base. The pin is keyed and will only insert in one orientation. Align cradle orientation as desired. Tighten the set screw with the included Allen wrench. Do not drive the set screw through the pin, only tighten the screw so it grabs the pin. Once set, the cradle should not be forced to a different position. To adjust, first loosen the set screw, tilt and rotate to realign, and then fasten the screw again.
A variety of spacers and rubber pads are included to provide the best support for the iPod. These are held in place by a double sided tape, and may be removed by the end user if a thicker iPod is used later on.
For Factory Pre-Wired Vehicles
1. Locate the fiber optic connector and CD changer control wires, shown in the images below. Refer to the Factory CD Changer Locations chart on page 1 for details. <- pin1 - GND <- pin2 - +12V <- pin 3 - control

Fiber Optic Connector

CD Changer Power and Control wire
2. Open the fiber optic connector and CAREFULLY remove the white and red fiber optic cable from both the factory harness and from the fiber optic adapter box. You will end up with 4 fiber cables - 2 red / 2 white.
3. Using the included couplers, connect the fiber optic cables as shown in the Connection Diagram BELOW. Connect the red to the white for both pairs of fiber optic cables. Press down on the metal clips until they snap in place to secure the cables. Connect the CD Changer Power and Control wires to the corresponding wires coming from the car specific adapter.
For Non Pre-Wired Vehicles
1. Remove radio from vehicle. 2. Connect fiber optic connector to the back of the radio(A). If there is a connector already plugged into the fiber optic port, then the car is most likely pre-wired for CD changer. In this case please refer to the pre-wired installation instructions.
Power, Ground and Wakeup Connections (Non-Pre-Wired)
Note: It is normal for the ice>Link to display a BMW or Kenwood configuration message.
Splice Red wire from car adapter into the Red/Black wire at pin 5 on the 10 pin connector C at the back of the radio Connect the Blue wire from the car adapter to pin 4 in 10-pin connector C at rear of radio
Connect black wire from adapter to pin 6 in 10-pin connector C at rear of radio
Connect blue wire from adapter to pin 4 in 18pin connector at rear of radio
Connect black wire from adapter to pin 8 in 8pin connector A at rear of radio Fiber Optic Connector Connect red wire from adapter to +12 Volt pin 4 in 8-pin connector A at rear of radio

Troubleshooting

If iPod does not charge 1. Check all connections. 2. Make sure that charge control is not turned off (see users manual pages 11 and 12). 3. Connect the iPod to a computer to see if it will charge from there. If you can not hear music playing 1. Make sure CD changer, SAT mode, or AUX is selected on your radio; the correct key will depend on your radio system and the installation type 2. Make sure that an album or playlist is selected on the iPod. If you can not switch your radio to CD changer mode 1. Check cables to make sure everything is tight. 2. Remove the fuse of the radio, wait for 30 seconds, and then reinsert the fuse. This will reset your radio and the interface. You may have to enter the radio security code, so please keep it handy. 3. Consult with your installer or contact your local Dension support center. If you can not control the iPod from the radio 1. Make sure the firmware on your iPod is the most recent. For updates please visit www.apple.com/ipod 2. Reset the iPod - hold the center button and the Menu buttons until iPod reboots. (Resetting will not erase your music, it will only restart the operating system of the iPod.) If iPod does not turn on 1. Verify that the iPods battery is not depleted by attempting to turn it on without connecting it to the car. 2. Turn off both your car stereo, and the iPod before inserting it to the cradle. Power on your radio and select the appropriate source. If the music is distorted or the sound level is too low 1. Check and make sure all EQ and BASS boost options are turned OFF on your iPod. 2. Make sure the Gain control is adjusted properly on the ice>Link, located under ice>Link setup. Why is the menu size small on the iPod photo? 1. iPod photo has a high resolution screen, and therefore everything appears smaller. 2. At the time of development, iPod photo specifications were not available. A future firmware upgrade may enlarge menu size. Please make sure that you connect the plug and the receptacle in the right orientation and that the housing latches to ensure tight retention.

Incorrect

Correct
Disclaimer / FCC Information / Warranty and Support
Important Disclaimer, please read !
Driving is dangerous and requires concentration. Do not allow the Apple iPod to distract you from prevailing traffic conditions. If in doubt, only operate the unit when stationary or ask a passenger to operate it for you. Do not submerge or expose to water or other fluids. ice>Link is NOT water proof and it will be damaged by water. You must properly insulate its casing if your installation environment may subject the unit to water, such as a convertible vehicle.
Keep away from children !
The ice>Link cradle can be broken, or disassembled, and components may become loose from vibration and heat. Small components and packaging materials may become choking hazard when handled by children. Unauthorized reproduction, or reverse engineering is strictly prohibited ! Intellectual property included is distributed under specific of general agreement with respective vendor(s). No warranty, explicit or implied is stated, and neither Dension USA, nor any of its distributors, dealers or vendors shall be liable for damages. IN NO EVENT SHALL DENSION USA'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. Dension ice>Link is a registered trademark of Dension Audio System LTD, and/or Dension USA, Inc. All other products are registered and copyrighted by their respective owners.
FCC Instruction to the user
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: o Reorient or relocate the receiving antenna. o Increase the separation between the equipment and receiver. o Consult the dealer or an experienced radio/TV technician for help. This equipment has been verified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment.

Warranty and Support

The Dension ice>Link Plus carries a one year limited warranty that protects you from defects in material and workmanship of products sold by Dension USA or its authorized agents, distributors and dealers. We do not warrant any installation. If you experience any problem or need help, please contact Dension USA support at www.densionusa.com , or by phone at (562)- 595-5143. To order accessories, call us at (562) 595-5153. Proof of purchase is required. Warranty does not cover normal tear and wear, damages due to negligence, improper installation or operation.

Notes:

End-User Install Certificate

Consumer

Name: Address:

Installer

Phone:

Product:

Firmware Version:
Mark location of components here.

Customization Performed