Users Guide

Warning
For your protection, please read the following:
Water and Moisture: Appliances should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. These symbols are internationally accepted symbols that warn of potential hazards with electrical products.The lightning flash means that there are dangerous voltages present within the unit.The exclamation point indicates that it is necessary for the user to refer to the owners manual. These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturers warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage. Power Sources: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Grounding or Polarization: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. Power Cord Protection: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. Servicing: To reduce the risk of fire or electrical shock, the user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. For units equipped with externally accessible fuse receptacle: Replace fuse with same type and rating only.
Electromagnetic Compatibility
Operation is subject to the following conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Use only shielded interconnecting cables. Operation of this unit within significant electromagnetic fields should be avoided.
DECLARATION OF CONFORMITY
Manufacturers Name: Manufacturers Address: declares that the product: Product name: Note: Product option: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA RP100 A Product name may be suffixed by the letters EX, EU, JA, and UK. all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.)
conforms to the following Product Specifications: Safety: EMC: Supplementary Information: The product herewith complies with the requirements of the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC as amended by Directive 93/68/EEC. DigiTech Vice-President of Engineering 8760 S. Sandy Parkway Sandy, Utah 84070, USA Date: September 22, 2003 European Contact: Your local DigiTech / Johnson Sales and Service Office or Harman Music Group 8760 South Sandy Parkway Sandy, Utah 84070 USA Ph: (801) 568-7533 Fax: (801) 568-7573 IEC 60065 (1998) EN 55013 (1990) EN 55020 (1991)

Warranty

We at DigiTech are very proud of our products and back-up each one we sell with the following warranty: 1.The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2. Digitech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. 3. Digitech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to Digitech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year. A Return Authorization number may be obtained from Digitech by telephone.The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly. 4. Proof-of-purchase is considered to be the burden of the consumer. 5. Digitech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured. 6.The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone other than a certified Digitech technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer. 7.The foregoing is in lieu of all other warranties, expressed or implied, and Digitech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall Digitech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. NOTE:The information contained in this manual is subject to change at any time without notification. Some information contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed.The information contained in this version of the owner's manual supersedes all previous versions.

Table of Contents

Safety Information...I Declaration of Conformity..II Table of Contents..III Getting Acquainted Included Items..1 A Guided Tour..2 Front Panel...2 Rear Panel...5 Getting Started...6 Making Connections...6 Mono Operation..6 Stereo Operation...7 Applying Power...8 Battery Power...8 AC Power..9 About the RP100 Artist..10 The Presets...10 Performance Mode...10 Bypass Mode...10 Tuner Mode..11 Compressor...16 Amp Modeling...17 EQ...17 Cabinet/Gate..18 Effects...19 Chorus...19 Flange...20 Phaser....20 Tremolo...20 Panner....21 Vibrato...21 Rotary...21 Auto Yah...22 Envelope..22 Pitch Shift...22 Detune...23 Whammy..23 Delay...24 Reverb...24
Section One - Introduction
Section Four - Other Functions
Expression Pedal...25 Drum Machine...25 Factory Reset...26
Section Two - Editing Functions
Editing/Creating a Preset...12 The Matrix...13 Storing/Copying..14
Section Five - Appendix Functions
Specifications..27 Preset Lists...28
Section Three - Effects and Parameters
About the Effects...15 Effect Definitions..15 Pickup/Wah...16

Section-1 Introduction

Getting Acquainted
Congratulations on your purchase of the RP100 Artist.You now have the flexibility and power to produce sonic creations never before thought possible. Although the RP100 Artist is so user friendly you may not even need to read this manual, we recommend that you become better acquainted with us, and what we have to offer by going through this Users Guide with your RP100 Artist in front of you. It is your key to unlocking the potential within the RP100 Artist.

Included Items

Before you get started, please make sure that the following items have been included: RP100 Artist PS0913B Power Supply Users Guide Warranty Card
The utmost care was taken while your RP100 Artist was being manufactured. Everything should be included and in perfect working order. If anything is missing, contact the dealer that you purchased the product from at once. Please help us become acquainted with you and your needs by completing your warranty card. It is your safeguard should a problem arise with your RP100 Artist.
A Guided Tour of the RP100 Artist The Front Panel
1. Footswitches - These 2 Footswitches are used to select Presets, access the Tuner, or bypass the RP100 Artist.The Footswitch on the right will increase, and the Footswitch on the left will decrease the selected Preset. Pressing both Footswitches together will bypass the currently selected Preset. Pressing and holding both Footswitches will access the Tuner. 2. Parameter Knobs - The Parameter knobs perform various functions depending on which mode is currently active in the RP100 Artist. In performance mode, these knobs control the Gain, Amp Type, and Master Level. In Edit mode, these knobs adjust the Parameter values listed directly above each knob for the selected effect.When the Drum machine is enabled, these knobs control the Pattern,Tempo, and Level. In Tuner mode, these knobs are used to select the desired tuning reference. 3. Select Button - This button is used to enter the Edit mode, and to select individual effect to be edited. Successive presses of this button will advance through all available Effects. 4. Drums - The Drums button is used to turn on and off the drum machine.When the Drums feature is active, the Drums LED lights and the selected drum pattern plays continuously. 5. Matrix - The matrix provides information regarding the current Preset, and Parameter edit functions. In performance mode, the 9 LEDs running down the left side of the Matrix will provide a visual indication of which effects are in use for the currently selected Preset. In Edit mode, the LEDs indicate the Effect currently selected for editing. In Tuner mode, the LEDs indicate whether the note played is sharp, flat, or in tune.

6. Display - The Display provides information for different functions depending on the mode that has been selected. In Performance mode, the Display will show the currently selected Preset number. In Edit mode, the Display will show the value of the parameter being adjusted. In Tuner mode, the Display will show the note played. 7. Store - The Store button is used to save your custom edits to the user Presets.

Rear Panel

1. Input - Connect your instrument to this jack. 2. Output - This is a stereo TRS jack. Connect from this jack to the input of a single amplifier for mono applications, or use a TRS stereo Y cord to connect to the inputs of 2 amplifiers for stereo applications. 3. Control In - Connect an expression pedal or volume pedal to this jack for the purpose of controlling Volume, Wah, or Whammyin the RP100 Artist. 4. Headphones - Connect a pair of stereo headphones to this jack. 5. Power Input - Connect only the optional DigiTech PS0913B power supply to this jack.
Getting Started Making Connections
There are several different connection options available with the RP100 Artist. Before connecting the RP100 Artist, make sure that the power to your amplifier and the RP100 Artist is turned off. There is no power switch on the RP100 Artist.To turn the RP100 Artist on or off, connect or disconnect your instrument to the Input Jack (for battery power) or connect the included PS0913B power supply from the Power Jack to an AC outlet (for AC power). Mono Operation Connect your guitar to the Input of the RP100 Artist. Connect a single mono instrument cable from the Stereo Output of the RP100 Artist to the instrument input on your amplifier, or to the line input of a power amp.
Stereo Operation For stereo operation connect the guitar to the Input of the RP100 Artist. Connect a TRS stereo Y cord to the RP100 Artists Stereo Output. Connect one end of the Y cord to the input of one amplifier, channel of a mixer, or power amp. Connect the second end of the Y cord to a second amplifier, second channel of a mixer, or power amp. If connecting to a mixing console, set the pan controls of the mixer hard left and right in order to retain stereo separation and be sure to engage the RP100 Artists Cabinet Emulator. See page 18 for more on selecting the Cabinet Emulator.
NOTE: When using a guitar amp, it may be best to connect the guitar to the input of the RP100 Artist and the Output of the RP100 Artist to the effect return of the amplifier.

Applying Power

There are two options for powering the RP100 Artist: battery power and AC power. Before applying power to anything, set your amp(s) to a clean tone and set the tone controls to a flat EQ response (on most amps, this would be 0 or 5 on the tone controls).Then follow the steps listed below. Battery Power The RP100 Artist can be run for about 8 hours on 6 AA batteries.The battery compartment is located on the bottom of the RP100 Artist.The following diagram shows the correct polarity for battery installation.

Connecting your instrument to the Input of the RP100 Artist will engage the battery power and disconnecting your instrument from the Input of the RP100 Artist will disengage the battery power. Once the connections have been made, and the RP100 Artist is powered (indicated by numbers appearing in the Display), turn the RP100 Artists Master Level (far right knob) all the way down.Turn your amplifier(s) power switch to the on position and adjust the volume(s) to a normal playing level. Gradually increase the RP100 Artist Master Level to achieve the desired volume. To prolong the battery life, disconnect your instrument from the RP100 Artists Input when not in use.
AC Power The RP100 Artist can also be powered with the included PS0913B power supply. Once the audio connections have been made, turn the RP100 Artists Master Level (far right knob) all the way down. Connect the plug of the PS0913B power supply to the power jack on the rear panel of the RP100 Artist. Connect the other end of the PS0913B power supply to an AC outlet.Turn the power of your amplifier(s) to the on position and adjust the volume(s)to a normal playing level. Gradually increase the RP100 Artist Master Level to achieve the desired volume.

About the RP100 Artist

The Presets Presets are numbered locations of programmed sounds which reside in the RP100 Artist. Presets are recalled with the Footswitches.The active effects in each Preset will be indicated by the lighted LEDs in the Effect Matrix.The RP100 Artist comes with 40 User Presets (Presets 1U40U), 40 Factory Presets (Presets 41F-80F), and 40 Artist Presets (Presets 81A-120A).The User Presets are locations where your creations may be stored.The Factory Presets and Artist Presets will not allow you to store any changes to them.The 40 User Presets are exact duplicates of the 40 Artist Presets.This allows you to create your own Presets without the worry of losing any of the sounds that the RP100 Artist came with. Performance Mode When you first apply power to the RP100 Artist, it will power up in Performance mode. Performance mode provides access to all of the Presets within the RP100 Artist via the Right and Left Footswitches.The Parameter 1 (left) knob will adjust the Amp Gain (distortion), the Parameter 2 (middle) knob will select the Amp Type, and the Parameter 3 (right) knob will adjust the Master Level (volume). Bypass Mode The RP100 Artist Presets can be bypassed for a clean, unprocessed guitar tone.To bypass the RP100 Artist, press both Footswitches simultaneously.The Display will read By indicating the Preset is bypassed. Pressing both Footswitches simultaneously again will exit Bypass and return the RP100 Artist to the last Preset used.

Tuner Mode The Tuner in the RP100 Artist allows you to quickly tune or check the tuning on your guitar. Enter Tuner mode by pressing and holding both Footswitches simultaneously.The Display will briefly show tu indicating that you are in Tuner mode. To begin tuning, play a note on your guitar (a harmonic at the 12th fret usually works best).The Display shows the note being played. The Matrix LEDs indicate whether you are sharp or flat.The top 4 Red LEDs indicate the note is sharp and should be tuned down.The bottom 4 Red LEDs indicate the note is flat and should be tuned up.The center Green LED indicates the note is in tune. The output is muted in Tuner mode.
In Tuner mode, you can change your tuning reference.The default factory setting is A=440 Hz. (displayed as 40). Rotating the Parameter 1 knob will select alternate dropped tunings. Alternate tunings are A = Ab (displayed as Ab), A = G (displayed as g), and A = Gb (displayed as gb).The display window will briefly flash the currently selected tuning preference. Exit tuner mode by pressing both Footswitches simultaneously.

Editing/Creating Presets

Creating your own signature sound with the RP100 Artist is easy and intuitive.The RP100 Artist lets you create your own Presets, or fine tune existing Presets to suit your needs. When creating or editing a sound, you must first start with one of the User or Factory Presets. It is not possible to start with a completely empty Preset.The Preset number does not necessarily need to be the location which you intend to have it reside, as you can save your creation to any User Preset location during the store process. To edit or create a Preset: 1. Use the Footswitches to select a Preset which will be your starting point. 2. Once you have found a Preset that you wish to edit, press the Select button once.This will take you into the Editing mode. 3. Use the Select button is in conjunction with the Matrix to choose the effect you wish to edit. 4. Use the 3 Knobs to change parameter values to achieve the desired sound you want.

The Matrix

The Matrix is where all Effects and Parameters are selected for editing. In Edit mode, successive presses of the Select button will advance to the next Effect row.The LED will light indicating which Effect group has been selected. Each Effect will have up to 3 Parameters which can be modified.The Knob under each column of Parameters is used to change the value for the corresponding Parameter of the selected Effect. As a Knob is rotated, the Parameter value or status will be shown in the Display.
When the stored value of a Parameter is changed, the Store LED will light indicating that you need to store the changes. Changing Presets, or turning the power off before storing any changes will erase any changes made and revert to the stored values for the Preset.

Storing/Copying a Preset

Once the Preset has been modified to your liking, you may store your settings to any of the 40 User Preset locations (Presets 1-40). The following steps outline the procedure for storing changes to a Preset or copying a Preset to a different location:
1. Press the Store button once and the current Preset location will flash in the Display.This is asking you to select a User Preset location where your new sound will reside. 2. Select the User Preset location using the Footswitches. 3 Press the Store button again to save the changes. The procedure for copying one Preset to another Preset location is the same. Simply use the Footswitches to select the Preset that you want to copy, then follow the steps listed above.

About the Effects

The RP100 Artist can be thought of as several different virtual amplifiers, and individual, hi-tech stomp boxes.With stomp boxes, the order in which they are connected can make a big difference in how good the overall sound is. The following diagram shows the order of the effects contained in the RP100 Artist.

Effect Definitions

Each Effect within the RP100 Artist can be programmed to suit your personal tastes and application. Understanding how these Effects will alter the sound, and how each Parameter will alter the Effect will help you achieve the sound you are looking for.The following overview of the RP100 Artists effects outlines what each Effect and Parameter does.

Pickup/Wah

The Pickup Simulator lets you get the thick tone of a humbucker pickup from a guitar with single coil pickups, or the bright edgy sound of a single coil pickup from a guitar with a humbucker.This allows you to have the best of both worlds without having to change guitars during a performance. Wah is an effect controlled by an Expression Pedal making the guitar sound as if its saying Wah. Pickup Type - The Parameter 1 knob selects the Pick Up type which will be simulated. of - Turns the Pickup Simulator off. hb - Gives a single coil pick up the warm tone of a humbucker. sC - Gives a humbucker the unique sound of a single coil. Wah Type - The Parameter 2 knob selects the Wah Type. of - Turns the Wah Effect off. cr - Cry Wah is a traditional sounding Wah. bt - Boutique Wah is a wider sweeping Wah with a more modern sound. fr - Full Range Wah sweeps the entire spectrum of audible frequencies. Wah Position - The Parameter 3 knob adjusts the Wah Pedal Position. Ranges from 0 (toe up) to 99 (toe down).

Compressor

A Compressor is used to increase sustain, tighten up guitars, and prevent the signal from clipping the input of other effects. It sets a maximum boundary for the strength of a signal. Comp Type - The Parameter 1 knob selects the Compressor Type (Attack). of - Turns the Compressor off. 1 to 3 - Controls the length of time it takes for the Compressor to respond to a signal exceeding the boundary.
Amount - The Parameter 2 knob adjusts the Amount of Compression (ratio and sustain) and ranges from 1 (slight compression) through 20 (maximum sustain). Gain - The Parameter 3 knob adjusts the Output Gain from the Compressor. Ranges from 0 to 6.

Amp Modeling

Amp Modeling is a technology which applies the tone of several popular modern and vintage amps. Amp Modeling also includes an acoustic guitar simulation. Amp Gain - The Parameter 1 knob adjusts the Gain (distortion) for the selected Amp Model (not available for Acoustic).The Gain parameter ranges from 0 to 99. Amp Level - The Parameter 2 knob adjusts the Level (volume) of the selected Amp Model. The Level parameter ranges from 0 to 99. Amp Type - The Parameter 3 knob selects the 12 types of Amp Models. bf bo re hr td C1 Based Based Based Based Based Based on on on on on on a 65 Fender Twin Reverb a Matchless DC30 a Mesa Dual Rectifier a Mesa Boogie Mark II C a 57 Fender Tweed Deluxe a Vox AC30 top boost C2 St Cr Hg Fu AC - A clean tube combo setting - Based on a Marshall JCM900 - A nice crunchy combo - Based on the Johnson JM150 High Gain - A vintage fuzz distortion - A flat top acoustic guitar
Marshall is a registered trademark of Marshall Amplification Plc. Vox is a registered trademark of Korg UK. Fender, Matchless, and Mesa Boogie, are trademarks of their respective companies and are in no way associated with DigiTech.
Equalization is an extremely useful tool used to further shape the tonal response of your guitar signal.The EQ in the RP100 Artist is similar to the tone knobs on an amplifier. All three EQ parameters range from -12dB to +12 dB.

Bass - The Parameter 1 knob adjusts the amount of low end enhancement (Bass). Mid - The Parameter 2 knob adjusts the amount of mid range enhancement. Treble - The Parameter 3 knob adjusts the amount of high end enhancement (Treble).

Cabinet/Gate

The Cabinet Modeling simulates different types of miked speaker cabinets.You have your choice of 3 Cabinet Types and 4 Mic Placements in relationship to the speaker cabinet. A Noise Gate is designed to eliminate noise while you are not playing. Cabinet/Mic - The Parameter 1 knob selects the type of simulated Speaker cabinet and mic placement in relation to the speaker.
Of - Cabinet Modeling off C1 - Bright 2x12 Mic 1 A1 - Dark 4x12 Mic 1 b1 - Warm 4x12 Mic 1 C2 - Bright 2x12 Mic 2 A2 - Dark 4x12 Mic 2 b2 - Warm 4x12 Mic 2 C3 - Bright 2x12 Mic 3 A3 - Dark 4x12 Mic 3 b3 - Warm 4x12 Mic 3 C4 - Bright 2x12 Mic 4 A4 - Dark 4x12 Mic 4 b4 - Warm 4x12 Mic 4 Gate Type - The Parameter 2 knob selects between the Silencer Noise Gate, or the Auto Swell volume swell effect.
Of - Turns the Noise Gate off. ng - Selects the Silencer Noise Gate. A1 to A9 - Selects the Auto Swell volume swell effect. These settings will automatically ramp up the volume from a 200 milliseconds volume fade in to 2 second volume fade in. Gate Thresh - The Parameter 3 knob sets the signal strength (Threshold) required to open or close the Noise Gate.The Gate Threshold parameter ranges from 1 (opens easily) to 40 (requiring strong signals to open).

Effects

The Effects row in the RP100 Artist is a multi-function module, allowing you to select effects such as; Chorus, Flanger, Phaser,Tremolo, Panner, Rotary Speaker,Vibrato, AutoYah, Envelope, Pitch Shift, Detune, and Whammy effects. When the Effects row is selected, the Parameter 3 knob is used to choose the type of Effect to be used. Only one of the effects in this row can be used at a time. After selecting the type of effect in this module, the Parameter 1 and Parameter 2 knobs can then be used to adjust the individual parameters associated with the selected effect.The following list describes each Effect and their parameters in more detail: Chorus (CH) A Chorus adds a short delay to your signal.The delayed signal is modulated in and out of tune and then mixed back with the original signal to create a thicker sound. Amount - The Parameter 1 knob simultaneously adjusts the rate (Speed) and intensity (Depth) of the modulation. Ranges from 1 to 99. Level - The Parameter 2 knob controls the mix level of the Effect. Ranges from 0 to 99.

Flange (FL) A Flanger uses the same principle as a Chorus but uses a shorter delay time and adds regeneration (or repeats) to the modulating delay.This results in an exaggerated up and down sweeping motion to the effect. Amount - The Parameter 1 knob simultaneously adjusts the rate (Speed) and intensity (Depth) of the Effect. Ranges from 1 to 99. Level - The Parameter 2 knob controls the mix level of the Effect. Ranges from to 99. Phaser (PH) A phaser splits the incoming signal, and then changes the phasing of the signal.This signal is then taken in and out of phase and mixed back in with the original signal. As the phasing changes, different frequencies get canceled resulting in a warm sort of twisting sound. Amount - The Parameter 1 knob simultaneously adjusts the rate (Speed) and intensity (Depth) of the Effect. Ranges from 1 to 99. Level - The Parameter 2 knob controls the mix level of the Effect. Ranges from 0 to 99. Tremolo (tr) A Tremolo effect modulates the volume of the signal at an even rate. Amount - The Parameter 1 knob adjusts the rate (Speed) at which the volume modulates. Ranges from 1 to 99. Level - The Parameter 2 knob adjusts the intensity (Depth) of the modulating volume. Ranges from 0 to 99.
Panner (Pa) An Auto Panner modulates the sound from left to right at an even rate. Amount - The Parameter 1 knob adjusts the rate (Speed) at which the signal pans from side to side. Ranges from 1 to 99. Level - The Parameter 2 knob adjusts the intensity (Depth) of the changing pan. Ranges from 0 to 99. Vibrato (br) A Vibrato effect modulates the pitch of the incoming signal at an even rate. Amount - The Parameter 1 knob adjusts the rate (Speed) at which the pitch modulates. Ranges from 1 to 99. Level - The Parameter 2 knob adjusts the intensity (Depth) of the modulating pitch. Ranges from 0 to 99. Rotary Speaker (RS) Rotary Speaker is an emulation of a device that included a spinning horn and woofer.The rotation of these two speakers produced an interesting combination of the sound panning from side to side, as well as a slight pitch change due to speed of the sound coming towards, and then going away from the listener. Amount - The Parameter 1 knob adjusts the rate (Speed) of the spinning speakers. Ranges from 1 to 99. Level - The Parameter 2 knob controls the mix level of the Effect. Ranges from 0 to 99.

AutoYah (AY) An AutoYah combines the characteristics of a Wah and a Flanger together creating an almost human vowel characteristic as if the guitar were saying Yah. The AutoYah provides animation to the sound automatically based on string attack. Amount - The Parameter 1 knob adjusts the rate (Speed) of the sweep. Ranges from 1 to 99. Level - The Parameter 2 knob adjusts the intensity (Depth) of the vowel sound. Ranges from to 99. Envelope Filter (En) The Envelope Filter is a dynamic Wah effect that alters your sound based upon how hard you play. Amount - The Parameter 1 knob adjusts sensitivity or the input signal required to trigger the Wah effect. Ranges from 1 to 99. Level - The Parameter 2 knob controls the mix of the Envelope effect. Ranges from 0 to 99. Pitch Shift (Pt) The Pitch Shifting copies the incoming signal, then shifts the pitch of the copy to a different note. The shifted note is then mixed back with the original signal sounding as if two guitars were playing different notes. Amount - The Parameter 1 knob selects the interval of the shifted pitch. Ranges from -12 to 24. Level - The Parameter 2 knob controls the mix level of the shifted pitch. Ranges from 0 to 99.
Detune (dt) A Detuner will make a copy of your incoming signal, take the copied signal slightly out of tune from the original, and mix the two signals together.The result is a doubling type of effect as if two guitars were playing the same part together. Amount - The Parameter 1 knob adjusts the amount of pitch difference applied to the copied signal. Ranges from -12 to 12. Level - The Parameter 2 knob controls the mix of the detuned note. Ranges from 0 to 99. Whammy (bd) Whammy is an effect that uses an Expression Pedal to bend the pitch of the incoming signal, or add a bendable harmony with the original signal. As the Pedal is moved, the note will bend either up or down. Amount - The Parameter 1 knob selects the interval and direction of the pitch bend.
Whammy (no Dry Signal) 1 (1 octave above) 2 (2 octaves above) 3 (a 2nd below) 4 (a 2nd below reversed pedal action) 5 (a 4th below) 6 (1 octave below) 7 (2 octaves below) 8 (6 octaves below) Harmony Bends (Dry Signal Added) 9 (a minor 3rd to a Major 3rd) 10 (a 2nd above to a Major 3rd above) 11 (a 3rd above to a 4th above) 12 (a 4th above to a 5th above) 13 (a 5th above to 1 octave above) 14 (1 octave above) 15 (1 octave down)
Level - The Parameter 2 knob adjusts the volume of the Whammy. Ranges from 0 to 99.
Delay is an effect that will record a portion of the incoming signal, and then play it back a short time later.The recording can repeat just once or several times. Type/Level - The Parameter 1 knob selects one of the 3 different types of Delay, as well as the volume level of the Delay. OF - Turns the Delay Effect off. 1d through 9d - These are Digital Delays with Level control. 1A through 9A - These are Analog Delays with Level control. 1P through 9P - These are Ping Pong Delays with Level control. Delay Time - The Parameter 2 knob adjusts the amount of Delay time. Ranges from 1 through 99(10 through 990 ms), and 1 and 2(1 and 2 seconds). Delay Feedback - The Parameter 3 knob adjusts the number of repeats. Ranges from 0 to 99.

Reverb

Using reverb in recorded program material gives the listener a sense that the material is being performed in an actual room or hall. It is this similarity to actual acoustic spaces that makes reverberation a useful tool in recorded music. Reverb Type - The Parameter 1 knob selects the Type of Reverb or acoustic space. Decay - The Parameter 2 knob adjusts the length of the Reverb. Ranges from 1 to 99. St=Studio ro=Wood Room CL=Club PL=Plate HA=Hall AP=Amplitheater CH=Church gA=Parking Garage Ar=Arena SP=Spring
Reverb Level - The Parameter 3 knob adjusts the volume of the Reverb. Ranges from 0 to 99.

Expression Pedal

The rear panel of the RP100 Artist includes an input for an expression pedal. Any passive volume pedal will operate as an expression pedal with the RP100 Artist. Connect from the output of a passive volume pedal to the Expression Pedal Input on the RP100 Artist.The expression pedal will control the RP100 Artists Volume,Wah, or Whammy parameters. If Wah and Whammy are disabled, the expression pedal will function as a volume pedal. If the Wah or Whammy effects are enabled, the expression pedal will control these effects.

Drum Machine

The RP100 Artist includes several sampled drum patterns which are useful for developing a good sense of timing. Pressing the Drums button will enable drum machine and start playback of the drum pattern (except when in Store or Bypass mode). In Drums mode, the Parameter 1 knob selects the drum Pattern, the Parameter 2 knob adjusts the drum Tempo, and the Parameter 3 knob adjusts the Level of the drum loop. Press the Drums button again to stop playback of the drum loop.

Factory Reset

This function resets the RP100 Artist to its original factory settings.This procedure will erase all custom user Presets, and recalibrate the Expression Pedal. ATTENTION: Performing this function will erase all user-programmed data. All such data will be lost forever! Be sure you want to erase the memory and start fresh before continuing with this procedure. The procedure for performing a Factory Reset is as follows: 1. Disconnect the power supply from the RP100 Artist (AC Power) or unplug the guitar from the input jack (battery power). 2. Press and hold the Select button while re-connecting the power or plugging your guitar into the RP100 Artists input. 3.When the display shows --, release the button and press then press the Store button. The display will then read rEand the RP100 Artist will reset to the original factory settings.

Section Five - Appendix

Specifications
Input: 1/4 Output: 1 - 1/4 Stereo TRS Headphone: 1/8 Stereo TRS A/D/A: 24 bit Delta Sigma Power Supply: 6 AA Batteries or 9 VAC, 1.3A (PS0913B) Power Consumption: 1.3A Memory: 40 User/40 Factory/40 Artist Presets Effects: Pickup Simulator,Wah, Compressor, 12 Amp/Guitar Models, 3 band EQ, Noise Gate, Cabinet Modeling, Mic Placement, Chorus, Flange, Phaser,Tremolo, Panner,Vibrato, Rotary Speaker, Auto Yah, Enveloped Filter, Pitch Shift, Detune,Whammy, Delay, and Reverb. Drum Machine: 30 Patterns Simultaneous Effects: up to 11 Dimensions: 8.25 L x 6.25 W x 2.25 H Weight: 2.25 lbs. w/ power supply

DigiTech and RP100 Artist are trademarks of the Harman Music Group Inc. Copyright the Harman Music Group
RP100 Artist Owners Manual 18-1867V-A Please visit DigiTech on the World Wide Web at: http://www.digitech.com

DigiTech RP100.

DigiTech , A&T Trade. . DigiTech A&T Trade, A&T Trade , .

. . . . , . .

RP100
: , . . : , . : . : . . : , . . , : .
. . . 1. 2 , RP100. , . . . 2. , RP100. , , -. , . , , . , . 3. Select . . 4. Rhythm / . , Rhythm, . 5. . , 9 . , . , . 6. . , . , . , . 7. Store .

. RP100. . RP100.

Pickup/Wah. Compressor. Amp Model. Equalizer. Cabinet/Gate. Effects. Delay. Reverb.

. . . . .

RP100 : RP100
6 AA 8 . RP100. . RP100 , . ( ), Master Level. Master Level . , RP100 .
1. Input . 2. Output TRS. , Y-, . 3. Control In RP100. 4. .
RP100 PS0913B. , Master Level. PS0913B RP100. PS0913B . Master Level .

5. PS0913B.

, RP100. . RP100, RP100. / RP100, Input ( ) PS0913B RP100 ( ).
RP100. . . RP100 40 (1-40) 40 (41-80). . . , 40 40.
RP100, . RP100 . 1 () (), 2 () , 3 () - ().

(Bypass)

Input RP100. Stereo RP100 . , RP100, Output . RP100, . By, . RP100 .
RP100 . . tu, . , . . 4 ( ). 4 ( ). . .
Input RP100. TRS Y- Stereo RP100. Y- . Y- . Cabinet Emulator, .
. A = 440 ( 40). 1 : A = Ab ( Ab), A = G ( g) A = Gb ( gb). . .
RP100 . , . . . : 1. . 2. Select . 3. Select . 4. .

RP100 , , . RP100 .

Whammy

Pickup/Wah (/)

, . - . Pickup Type - 1 . of - hb - sC - Wah Type - 2 . of - cr - bt - fr -
, Select , . 3 . . , .
Wah Position - 3 . 0 () 99 ().

Compressor ()

. Comp Type - 1 (). of - - Amount - 2 ( ) 1 () 20 (). Gain - 3 . 0 6.

, Store. .

(1-40).

Amp Model ( )

, . Amp Gain - 1 () ( ). 0 99. Amp Level - 2 () . 0 99. Amp Type - 3 12 . bf - 65 Fender Twin Reverb bo - Matchless DC30 re - Mesa Dual Rectifier hr - Mesa Boogie Mark II C td - 57 Fender Tweed Deluxe C1 - Vox AC30 C2 - St - Marshall JCM900 Cr - Hg - Johnson JM150 High Gain Fu - AC -

Equalizer ()

1. Store, . 2. . 3. Store . . RP100 3- 12. Bass - 1 . Mid - 2 . Treble - 3 .

Cabinet/Mic/Gate (/)

Cabinet 3 4 . Noise Gate . Cabinet/Mic - 1 . Gate Type - 2 : Silencer . Of - A1 - 4x12, 1 A2 - 4x12, 2 A3 - 4x12, 3 A4 - 4x12, 4 b1 - 4x12, 1 b2 - 4x12, 2 b3 - 4x12, 3 b4 - 4x12, 4 C1 - 2x12, 1 C2 - 2x12, 2 C3 - 2x12, 3 C4 - 2x12, 4 Of - ng - Silencer A1 A9 - . 200 2. Gate Thresh - 3 , . 1 () 40 ().
Amount - 1 . 1 99. Level - 2 . 0 99.
. Amount - 1 . 1 99. Level - 2 . 0 99.
, . Amount - 1 . 1 99. Level - 2 . 0 99.
, . Amount - 1 . 1 99. - 2 . 0 99.

Effects ()

Effects RP100 , . , 3 . . , , .
-, . Amount - 1 , , . 1 99. Level - 2 . 0 99.
. Amount - 1 . 1 99. Level - 2 . 0 99.
. Amount - 1 . -12 24. Level - 2 . 0 99.
, . Amount - 1 . 1 99. Level - 2 . 0 99.
, . Amount - 1 . -12 12. Level - 2 . 0 99.
, . Amount - 1 . 1 99. Level - 2 . 0 99.

Whammy (bd)

. Amount - 1 . Level - 2 . 0 99.

Whammy ( )

1 (1 ) 2 (2 ) 3 ( ) 4 ( ) 5 ( ) 6 (1 ) 7 (2 ) 8 (6 )

Harmony Bends ( )

9 ( ) 10 ( ) 11 ( ) 12 ( ) 13 ( 1 ) 14 (1 ) 15 (1 ).
Bypass). , 1 , 2 , 3 . Rhythm .
RP100 . : . . 1. RP100. 2. Select, RP100. 3. , Store, . rE, RP100 .

Delay ()

Type/Level - 1 . OF - . 1d 9d - . 1A 9A - . 1P 9P - - . Delay Time - 2 . ( ), (). Delay Feedback - 3 . 0 99.

Reverb ()

. . Reverb Type - 1 . St = ro = CL = HA = AP = CH = gA = SP = Ar = PL = Decay - 2 . 1 99. Reverb Level - 3 . 0 99.
, . . . , RP100, DigiTech A&T Trade. (095) 242-5325. E-mail: info@attrade.ru

: 1/4 : 1/4 TRS : 1/8 TRS -: 24 - : 9 , 1.3 (PS0913B) 6 AA : 40 /40 : , 12 , 3- , , , , , , , , , , , -, , , , , , , Whammy. : 30 : 12 : 210 , 159 , 57 : 1 ,
RP100 . Control In RP100. Volume, Wah Whammy. Wah Whammy , , . Wah Whammy , .
RP100 , . Rhythm ( Store