Instruction Manual

Important:
Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual!
ES-2130 A ES-2135 A ES-2140 A ES-2145 A

http://www.dolmar.com

Thank you for your trust in our product
We congratulate you on your new DOLMAR electric chain saw. We are convinced that you will be satised with this modern machine. DOLMAR electric chain saws are characterized by their robust, high-efciency motors and high chain velocities which allow an excellent cutting efciency. They are equipped with numerous state-of-the-art safety devices, are light, handy and can be put into operation immediately wherever electric power is provided. In order to guarantee the optimal function and performance of your electric chain saw and to ensure your personal safety we would request you to perform the following: Read this instruction manual carefully before putting the electric chain saw into operation for the rst time and strictly observe the safety regulations. Failure to do so can result in serious injury to the operator and/or bystanders.

Table of contents

Symbols
You will notice the following symbols on the chain saw and in the instruction manual:
Symbols... 2 Delivery inventory.. 3 Packing/Disposal... 3 Intended use... 3 SAFETY PRECAUTIONS General precautions... 4 Personal protective equipment.. 4 Putting into operation..4-5 Working behavior/method of working..5-7 Kickback... 7 Transport and storage.. 8 Maintenance... 8 First aid... 8 Technical data... 9 Denomination of components.. 9 PUTTING INTO OPERATION Mounting the guide bar and saw chain.. 10-11 Tightening the saw chain... 11 Checking the chain tension.. 12 Chain brake, Run-out brake.. 12 Saw chain oil... 13 Relling the oil tank.. 14 Lubricating the saw chain.. 14 Switching on the motor.. 15 Checking the chain brake... 16 Checking the run-out brake.. 16 Checking the chain lubrication.. 16 MAINTENANCE Sharpening the saw chain..17-18 Cleaning the guide bar/lubricating the sprocket nose.. 18 Replacing the saw chain.. 19 Inspecting and replacing the carbon brushes.. 19 Trouble shooting.. 20 Instructions for periodic maintenance.. 20 Service, spare parts and guarantee.. 21 Extract of spare parts list..22-23 Accessories...22-23 EU conformity declaration.. 23
Read instruction manual and follow the warnings- and safety precautions!
Maximum permissible cut length
Particular care and attention!

Wear protective gloves!

Wear protective helmet, eye and ear protection!
Protect against moisture!
Pull out the power supply plug!
Direction of chain travel
Pull out the power supply plug if the cable is damaged!
Double protective insulation
Saw chain oil Chain brake released First aid Chain brake actuated

Kickback!

Recycling

Forbidden!

CE-Marking

Delivery inventory

1. 2. 3. 4. 5. 6.
Electric chain saw Guide bar Saw chain Cord grip for electric cord Chain protection cover Instruction manual (not shown)
In the case that one of the parts listed should not be included in the delivery inventory, please, consult your sales agent.

Packing/Disposal

The DOLMAR electric chain saw will be delivered in a protective cardboard box to prevent transport damages. Cardboard is a basic raw material and is therefore consequently reuseable or suitable for recycling (waste paper recycling).

Intended use

Electric saws This electric saw may be used only for sawing wood. It is intended for occasional use in thin wood, caring for fruit trees, felling, removing limbs, and trimming to length. Persons who may not sue the saw: This saw must not be used by persons who are not familiar with this instruction manual, children, young people, or anyone under the inuence of alcohol, drugs or medication.
Be a good steward of the environment! Do not dispose of electrical appliances with the household trash!
If the saw is no longer operable or repairable, ask the appropriate waste disposal authority about the proper means of disposal. In order to preclude any hazard to other persons from a defective electrical appliance, cut off the power cord next to the housing. CAREFUL! Before cutting off the power cord, pull the plug. Otherwise you can be exposed to a life-threatening shock!

Personal protective equipment

Putting into operation

Pay attention to the diameter of the extension cable. When using a cable roll the cable should be completely wound off. Use only extension cords that meet the specications in Technical data. If using the saw out of doors make sure that the extension cord is approved for such use. Before starting work the electric chain saw must be checked for perfect function and operating safety according to the prescriptions. Check especially the function of the chain brake, the correct mounting of the guide bar, the correct sharpening and tightening of the saw chain, the rm mounting of the sprocket guard, the easy motion of the power switch, the function of the locking button, the good mechanical condition of cable and plug and the cleanliness and dryness of the handles. Put the electric chain saw only into operation if it is completely assembled. Never use the electric chain saw when it is not completely assembled. Remove the adjusting tool before switching the saw on. All protective installations and guard supplied with the chain saw during operation. Make sure that there are no children or other persons within the working range. Also pay attention to any animals in the working vicinity (6). Before switching on the electric chain saw ensure that you have a safe footing. When switching on the electric chain saw always hold it with both hands. Take the back handle with the right hand and the tubular handle with the left hand. Hold the handles tightly with your thumbs facing your ngers. The bar and chain must indicate away from your body (7). Switch on the saw only in the manner described in this manual. Do not overload your saw. It will work better and more safely if you use it within its intended performance range. Switch off the electric chain saw immediately if you observe a change in its operating behavior. CAUTION: When releasing the power switch the chain keeps on running for a short period of time (free-wheeling). Protect the power cord from heat, oil and sharp edges. Route the power cord in such a way that in cannot get caught in branches or other objects during sawing.- If the cable is being damaged or cut, pull out the power supply plug immediately. If the sawing device is hit by stones, nails or other hard objects, pull out the power supply plug and check the sawing device immediately Pull out the power supply plug before checking the chain tension, tightening the chain, replacing it or clearing malfunctions. When stopping work or leaving the electric chain saw switch off the chain saw and pull out the power supply plug. Put the electric chain saw in a safe location to prevent danger to others. For relling the oil tank the power supply plug must be pulled out. Do not smoke or light open res. Avoid skin or eye contact with mineral oil products. Always wear gloves when relling the oil tank. Take care that no chain oil oozes into the soil (environmental protection). Use an appropriate base. If oil has been spilt, clean the electric chain saw immediately. Do not work on your own. There must be someone around in case of an emergency (within shouting distance). During sawing operation always hold the electric chain saw with both hands. Thus you will be able to guide it safely. Only use the electric chain saw during good light and visibility periods. Be aware of slippery or wet areas, and of ice and snow (risk of slipping). The risk of slipping is extremely high when working on recently peeled wood (bark). Never work on unstable surfaces. Make sure that there are no obstacles in the working area, risk of stumbling. Always ensure that you have a safe footing. Never saw above your shoulder height. Never saw while standing on a ladder. Never climb up into trees to perform sawing with the electric chain saw. Never bend forward by far to perform sawing.

CAUTION: Do not fell or debranch trees unless you are specially trained for it! There is a high risk of injury! Make sure to follow local regulations. - Before cutting down a tree ensure that a) only those persons are within the working range which are actually involved in cutting down the tree b) all persons involved in the felling have an unhindered retreat route (the retreat path should be about 45 diagonally and to the rear away from the direction of fall). Be aware of the increased risk of stumbling from electric cables! c) the bottom part of the trunk is free from foreign bodies, underbrush and branches. Make sure to have a safe footing (risk of stumbling). d) the next working place is at least 2 1/2 tree lengths away (16). Before cutting down the tree check the direction of fall and make sure that there are neither other persons nor any objects within a distance of 2 1/2 tree lengths (16). - Judging the tree: Direction of hanging - loose or dry branches - height of the tree - natural hang over - is the tree rotten? - Take into account the direction and the velocity of the wind. If strong gusts are occuring, do not perform any cutting down works. - Cutting the roots: Start with the strongest root. First perform the vertical and then the horizontal cut. - Notching the trunk (A, 17): The notch determines the direction of fall and guides the tree. The trunk is notched perpendicular to the direction of fall and penetrates 1/3 -1/5 of the trunk diameter. Perform the cut near the ground. - When correcting the cut always do so over the whole width of the notch. - Cut down the tree (B, 18) above the bottom edge of the notch (D). The cut must be exactly horizontal. The distance between both cuts must be approx. 1/10 of the trunk diameter. - The material between both cuts (C) serves as a hinge. Never cut it through, otherwise the tree will fall without any control. Insert felling wedges in the cut (B, 18) in good time. - Secure the cut only with wedges made of plastic or aluminium. Do not use iron wedges. - When cutting down a tree always stay sideways of the falling tree. - When withdrawing after having performed the cut down be aware of falling branches. - When working on a sloping ground the user of the electric chain saw must stay above or sidewards of the trunk to be cut or the already cut down tree. - Be aware of trunks which may roll towards you.

= cutting down range

Kickback
- When working with the electric chain saw dangerous kickbacks may occur. - Kickback occurs when the tip of the blade(especially the top quarter) inadvertently comes into contact with wood or other solid objects. - In this case the electric chain saw is thrown without any control and with high energy potentials in the direction of the user (risk of injuries). In order to prevent kickbacks follow the indicated instructions: - Never apply the end of the bar when starting to make a cut. Always observe the end of the bar. - Never use the bar end for sawing. Be careful when continuing to cut. - When starting to perform a cut the chain must be running. - Ensure that the chain is always sharpened correctly. Pay special attention to the hight of the depth limiter (for detailed information see the chap. "Sharpening the saw chain"). - Never cut several branches at the same time. When cutting a branch ensure that no other branch is touched. - When crosscutting a trunk be aware of the trunks next to it. It is recommended to use a saw jack.

Maintenance

First aid

SERVICE

Technical data
Power consumption Nominal voltage Mains frequency Nominal current Fuse, electric circuit Cable length Chain type Chain pitch Length of a cut Max. chain speed

per EN 60745-2-13

ES-2130 A Watt V Hz A A cm inch cm m/s dB (A)
ES-2135 A - 240 ~ 50 - 60 8,30 / 3/8"

ES-2140 A

ES-2145 A

35 13,3 101,8 90,8

Sound power level LWA av
Sound pressure level LpA av dB (A) at the workplace per EN 60745-2-13 Vibration acceleration
ah,w av per EN 60745-2-13
- Tubular handle m/s2 - Rear handle m/s2 Oil pump Oil tank capacity ml Power transmission Overload protection Chain brake Run-out brake Weight (without bar/chain) kg kg Weight (with bar/chain) Radio interference suppression / EMC Protective case Extension cable

(not included)

4,7 5,6 automatic 140 direct electrical manually actuated electrical 4,4 5,1 5,2 Per EMC Directive 2004/108/EG class II (double protective insulation) DIN 57282/ HO 7RN-F L= 30 m max., 3x1,5 mm2
1 Denomination of components
Figure: Identication plate ES-2145A

2008 123456

Serial number Year of manufacture
230-240 V~ 50-60 Hz 8.8 A 2000 W

Typ 226

XXX XXX XXX
Tubular handle Hand guard (release for chain brake) Spike bar Sprocket guard quick tightener Sprocket guard, chain brake Carbon brush cover Back hand guard Power cord with plug Guide bar Oil tank cap Identication plate Locking button Rear handle Power switch Sightglass for oil level Saw chain Cord grip for electric cord (pull relief)
Indicate when ordering spare parts!

PUTTING INTO OPERATION

CAUTION: When working on the guide bar or saw chain always wear protective gloves and pull out the power supply plug. CAUTION: Switch on the electric chain saw only after having assembled it completely and inspected!
Mounting the guide bar and saw chain
Put the electric chain saw on a stable surface and carry out the following operations for mounting the bar and chain: Release chain brake. To do this, pull the hand guard (1) in the direction of the arrow.
Flip up the sprocket guard quick tightener (2) (see also Fig. G). Push in the sprocket guard quick tightener rmly against spring pressure, and slowly turn it counter-clockwise until you feel it engage. Keep pushing in, and turn it as far as possible counter-clockwise. Release the sprocket guard quick tightener (remove pressure) and now turn it clockwise to its original position. Repeat this procedure until the sprocket guard (3) is unscrewed. Pull the sprocket guard (3) up slightly, pull out of the rear ttings (4) and remove.

Chain brake

These models come with a chain brake as standard equipment. If there is a kickback resulting from the guide bar tip impacting the wood (see SAFETY INSTRUCTIONS, page 7), the back of the hand hitting the handguard will engage the chain brake. The chain will stop within a fraction of a second.

Run-out brake

The electric chain saw come with a run-out brake as standard equipment. The run-out brake ensures that the chain comes to a stop immediately when the ON/OFF switch is released, thus preventing the chain from continuing to run and presenting a hazard. Testing of the run-out brake is described on page 16.
Chain and run-out brake maintenance
The brake systems are very important safety features, and like any other part they are subject to a certain amount of wear. Regular inspection and maintenance is important for your personal safety, and can be properly performed only by a DOLMAR service centre.
Engaging the chain brake (braking)
With your left hand, press the handguard (1) towards the tip of the guide bar (arrow 2). Releasing the chain brake
Pull the hand guard (1) towards you (arrow 3) until you feel it catch. The brake is now released. Note: When the chain brake is actuated the power supply to the motor will be cut off. Testing of the chain brake is described on page 16.

Saw chain oil

Use a special oil with adhesive addition for lubricating the saw chain and bar. The adhesive addition prevents that the oil is centrifuged too fast from the sawing device. Do not use mineral oils. In order to protect the invironment the use of biologically decomposeable oil is prescribed. The saw chain oil sold by DOLMAR, called BIOTOP, is made of special vegetable oils and is biologically decomposeable to 100%. BIOTOP has been granted the "blue angel" for being particularly favourable to the environment (RAL UZ 48).
BIOTOP oil is available in the following packing sizes to suit your individual requirements: 1 liter order number liters order number liters order number 213 Biologically decomposeable oil is stable only for a limited period of time. It should be consumed within 2 years from the date of manufacture (printed on the container).
Important note on bio-degradable chain oils
If you are not planning to use the saw again for an extended period of time, empty the oil tank and put in a small amount of regular engine oil (SAE 30), and then run the saw for a time. This is necessary to ush out all remaining bio-degradable oil from the oil tank, oil-feed system, chain and guide bar, as many such oils tend to leave sticky residues over time, which can cause damage to the oil pump or other parts. The next time you use the saw, ll the tank with BIOTOP chain oil again. In case of damage caused by using waste oil or unappropriate chain oil the product guarantee will be null and void. Your salesman will inform you about the use of chain oil.

NEVER USE WASTE OIL

Waste oil is very dangerous for the environment. Waste oil contains high amounts of carcinogenic substances. The residues in the waste oil result in a high degree of wear and tear at the oil pump and the sawing device. In the case of damage caused by using waste oil or unappropriate saw chain oil the product guarantee will be null and void. Your salesman will inform you about the use of saw chain oil.

Waste oil

AVOID SKIN AND EYE CONTACTS
Mineral oil products as well as oil degrease the skin. If your skin repeatedly comes in contact with these substances for a longer period of time, it will desiccate. Various skin deseases may result. In addition, allergic reactions are known. Eyes can be irritated by contact with oil. If oil gets into your eyes, immediately wash them with clear water. If your eyes are still irrritated, go to see a doctor.

Relling the oil tank

Only if the motor is switched off and the power supply plug is pulled out! Thoroughly clean the oil tank around the cap to prevent dirt from entering the tank. Unscrew the tank cap (1) and ll in chain oil until it is on a level with the bottom edge of the ller socket. Tightly screw on the tank cap. Thoroughly remove any oil that has overown.
Important! Before operating the saw for the rst time, the oil feed system must be completely lled, until the chain oil lubricates the chain and guide bar. This procedure can take up to two minutes. The oil level can be controlled in the sight glass (2).
In order to ensure sufcient lubrication of the saw chain there must always be enough oil in the tank.
Lubricating the saw chain Only if the motor is switched off and the power supply plug is pulled out! To guarantee a troublefree operation of the oil pump the oil guide groove (3) as well as the oil inlet bore in the guide bar (4) must be cleaned in regular intervals. Note: After the saw has been turned off it is normal for residual chain oil to drip from the oil feed system, the guide bar and the chain for a time. This does not constitute a defect! Place the saw on a suitable surface.

Plug in the saw

CAREFUL! Before connecting the saw to a source of electricity, always make sure to check that when the ON/OFF switch (1) has been pressed in and released, it automatically comes back out to the "off" position. If it does not, do not under any circumstances connect the saw to a power source do not plug it in. Take the saw to a DOLMAR service centre before doing any work with it. Clip the extension cord and the saws power cord into the cord grip (2). Plug the saw plug (3) into the socket of the extension cable (4).

Switching on the motor

Plug in the saw (see above). When switching on the electric chain saw always hold it with both hands. Take the back handle with the right hand and the tubular handle with the left hand. Hold the handles tightly with your thumbs facing your ngers. The bar and chain must not be in contact with any object. First depress the locking button (5) and then the power switch (1). Then release the locking button (5). Attention: The chain starts running immediately. Keep the power switch depressed as long as the motor is to run.
CAUTION: Never lock the power switch in the ON position.

Switching off the motor

Release the power switch (1). NOTE: When the chain brake is actuated the power supply to the motor will be cut off. If the saw does not start when the ON/OFF switch (1) is actuated, it will be necessary to release the chain brake. Pull the hand guard (6) rmly in the direction of the arrow until you feel it catch.
Important: These models are equipped with a starting current limiter. This electronic component prevents too abrupt starting of the electric motor. Excess current cutoff: When the electrical current to the saw exceeds the permissible level, the power supply to the motor is automatically cut off. This prevents overheating of the motor and resulting damage. To start the saw up again, release the ON/OFF switch and press it again. CAUTION: Do not use the saw if the current cutoff repeatedly switches off the saw. Consult a DOLMAR service centre.

Checking the chain brake

Do not work with the chain saw without rst checking the chain brake! - Start the motor as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact). - Grasp the tubular handle rmly with one hand and hold the grip with the other. - Switch on the motor and press the hand guard (1) in the direction of the arrow with the back of your hand until the chain brake engages. The chain should stop immediately. - Switch the motor off Immediately and release the chain brake. Important: If the saw chain does not stop instantly when you carry out this test, do not under any circumstances use the saw! Take the chain saw to a DOLMAR service center.
Testing the run-out brake
Do not work with the saw without rst testing the run-out brake! Start the motor as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact). Grasp the tubular handle rmly with one hand and hold the grip with the other. Switch the motor on and then back off. The chain should come to a full stop within two second of switching off the motor. Important: If the saw chain does not stop within two second when you carry out this test, do not use the saw! Inspect the carbon brushes (see page 19).

The le holder makes le guidance easier. It is marked for the correct 30 sharpening angle (keep the marks parallel with the chain when ling, see illustration) and limits the cut depth to the correct 4/5 of the le diameter. See "Accessories" for the order number.
After having sharpened the chain, the height of the depth limiter must be checked by means of a chain gauge. See "Accessories" for the order number. Correct even the smallest excess height with a special at le (1). See "Accessories" for the order number. Round off the front of the depth limiter (2).
Cleaning the guide bar, lubricating the sprocket nose
CAUTION: Protective gloves must be worn. Regularly inspect the bearing surfaces of the guide bar for damage, and clean them with a suitable tool. If the saw is used intensively it will be necessary to lubricate the return sprocket bearings regularly (once a week). To do this, rst thoroughly clean the 2 mm hole at the tip of the guide bar, and then press in a small amount of multi-purpose grease. Multi-purpose grease and grease guns are available as accessories. Multi-purpose grease Grease gun (order no. 000) (order no. 000)

Replacing the saw chain

CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare parts list)! Check the sprocket (1) before mounting a new chain. CAUTION: Worn out sprockets (2) may damage the new chain and must therefore be replaced. Do not attempt to replace the sprocket yourself. Sprocket replacement requires special training and tools and must be done at a DOLMAR service centre.
Inspecting and replacing the carbon brushes
Important: Inspect the carbon brushes at regular intervals! A notch on the brush shows the limit of wear. NOTE: The carbon brush is very delicate, so be careful not to let it drop. When taking it out, be sure to note the position it was installed in, since each brush is run in with the rotor. Use a slotted bit screwdriver to unscrew the cover (1), and then pull out the brush (2). If the wear limit has not yet been reached, put the brush back in the same position and screw the cover (1) back on. Run the saw briey (about a minute) so the brushes can run in again.
Important: Now test the run-out brake (see page 16). If the saw chain does not come to a full stop within two second, run the saw again briey and repeat the test until the brake functions properly. NOTE: After installing new carbon brushes, run the saw about 5 minutes and then check the run-out brake.

Trouble shooting

Malfunction Chain saw does not work System total Observation electric motor does not function Cause no power supply, cable defective chain brake actuated Mains fuse blown

insufcient performance

Carbon brushes

low pulling power

Carbon brushes worn down

no chain lubrication

Oil tank, oil pump

no oil on the saw chain

oil tank empty,
Saw chain does not stop instantly

Brake band worn down

Saw chain continues to run
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents! The user of the electric chain saw is not allowed to perform maintenance works which are not described in the instruction manual. All other works must be carried out by a DOLMAR service centre. Page General work Electric chain saw Plastic case Saw chain Guide bar Regularly clean the outside. Check for cracks and ruptures. In case of damage have it immediately repaired at a service centre. Resharpen regularly. Replace in time. Turn over after a certain period of time so that the bearing surfaces are uniformly worn. Replace in time. Have it replaced in time at a service centre. Have it inspected regularly at a service centre. Have it inspected regularly at a service centre.
Sprocket Chain brake Run-out brake Each time before putting the saw into operation
Saw chain Guide bar Chain lubrication Chain brake Run-out brake Power switch Power supply cable Oil tank cap
Check for damage and sharpness. Check the chain tension. Check for damage, and remove burrs if necessary. Functional check. Functional check. Functional check. Functional check. In case of damage have it replaced at a service centre. Check for tightness. Clean the oil inlet bore. Clean, especially the oil guide groove. Empty. Demount, clean and lubricate slightly. Clean the guide groove of the guide bar. Store safely in a dry place. After a long storage time, have the electric chain saw checked at a service centre (residual oil can become resinic and the valve of the oil pump clogged).

17-16 15

After each shutdown
Guide bar Chain carrier Chain oil tank Saw chain/guide bar Electric chain saw

Storage

Service, spare parts and guarantee

Maintenance and repair

The maintenance and repair work of modern electric motors as well as all safety related assemblies require qualied technical training and the availability of a special workshop equipped with special tools and testing devices. Any work not described in this Instruction Manual must be performed only by a DOLMAR service centre. The DOLMAR service centres are provided with all the necessary equipment and skilled and experienced personnel to work out correct customer solutions and to advise you in all matters accordingly. Repair attempts by third parties or unauthorised persons void all warranty claims.

Spare parts

A reliable and continuous operation as well as the safety of your chain saw is also subject to the quality of the spare parts used. Use original DOLMAR spare parts only, marked: Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning and safety. Original spare parts and accessories can be obtained from your local dealer. He will also have the relative spare part lists to determine the required spare part numbers, and will be constantly informed about the latest improvements and also about spare part innovations. To nd your local distributor, please visit www.dolmar.com Please, take in mind that in the case that foreign spare parts are used instead of the original DOLMAR spare parts this will automatically invalidate the DOLMAR product guarantee.

Guarantee

DOLMAR guarantees the highest quality and will therefore reimburse all costs for mending through replacement of damaged parts as a result of material or production faults, which occur within the guarantee time after purchase. Please, note that in some countries particular guarantee conditions may exist. In case of any doubts, please, contact your salesman who is responsible for the guarantee of the product. We ask for your understanding that we cannot accept any responsibility for damage caused by: Disregard of the instruction manual. Non-performance of the required maintenance and cleaning instructions. Normal wear and tear. Obvious overload due to permanent excess of the upper limits of capacity. Use of guide bars and saw chains which have not been approved. Use of guide bar and saw chain lengths which have not been approved. Use of force, improper use, misuse or accidents. Damage caused by overheating due to dirt obstructing the cool air supply at the motor case. Use of unsuitable spare parts or parts which are not original DOLMAR parts, as far as they have caused the damage. Use of unsuitable or old oil. Damage related to conditions arising from lease or rent contracts. Works on the chain saw by unskilled persons or performance of inappropriate repairs.
Cleaning, servicing and adjustment works are not covered by the guarantee. All repairs covered by the guarantee are to be performed by a DOLMAR service centre.
Extract from the spare parts list
Use original DOLMAR spare parts only. For performance of repairs and for replacement of other components your DOLMAR service centre should be consulted.

ES-2130 A, ES-2135 A ES-2140 A, ES-2145 A

Pos. 6

DOLMAR No. 140

Qty. 1

Denominatio Oil tank cap compl. Sprocket guard compl. Carbon brushes Sprocket nose bar 30 cm (12") Sprocket nose bar 35 cm (14") Sprocket nose bar 40 cm (16") Sprocket nose bar 45 cm (18") Saw chain 3/8", 30 cm Saw chain 3/8", 35 cm Saw chain 3/8", 40 cm Saw chain 3/8", 45 cm Chain protection cover (30-35 cm) Chain protection cover (40-45 cm)
Accessories (not included in the delivery inventory) 1 Chain gauge 3/8 File handle Round le 4 mm Flat le File holder compl. 3/8
EU Conformity Declaration
The undersigned, Tamiro Kishima and Rainer Bergfeld, as authorized by DOLMAR GmbH, declare that the DOLMAR machines, Type: 226 ES-2130 A ES-2135 A ES-2140 A ES-2145 A EU prototype test certicate No. M068 M068 M068 M068
manufactured by DOLMAR GmbH, Jenfelder Str. 38, 22045 Hamburg, Germany, conforms to the basic safety and health requirements of the applicable EU guidelines: EU Machinery Directive 98/37/EG, EU EMC Directive 2004/108/EG, Outdoor Noise Directive 2000/14/EG. Starting on 29 Dec. 2009, Guideline 2006/42/EG will come into force, replacing Guideline 98/37/EG. This product meets the requirements of the new Guideline. The most important standards applied to properly meet the requirements of the above EU Directive were: EN 60745-2-13, EN 610003-2, EN 61000-3-3, EN 55014-1, EN 55014-2. The conformity assessment procedure 2000/14/EG was performed per Annex V. The measured sound power level (LWA) is 101,8 dB(A). The guaranteed sound power level (Ld) is 103 dB(A). The EU-Type-Examination Certificate was performed by: TV Sd Product Service GmbH, Zertifizierungsstelle, Ridlerstr. 31, D-80339 Mnchen. The technical documentation is on le at DOLMAR GmbH, Jenfelder Strae 38, Abteilung FZ, D-22045 Hamburg. Hamburg, 15.5.2008 For DOLMAR GmbH
Tamiro Kishima Managing Director
Rainer Bergfeld Managing Director

To nd your local distributor, please visit www.dolmar.com
DOLMAR GmbH Postfach 20 D-22004 Hamburg Germany http://www.dolmar.com
Specications subject to change without notice

Form: 303 (2.09 GB)

ES-2140 AP

Powerful and reliable

5 m cable as a standard
Tool-less chain tensioner (TLC)

Metal spike bar

Soft handle and big trigger switch provide safety and comfort
Technical specifications Rated voltage Power consumption Net weight Oil tank capacity Chain tensioning Automatic oilpump Guide bar 230 V 2.000 W 5,2 kg 140 ml Toolless Chain tensioning (TLC) yes 40 cm Chain Sound pressure level Sound power level Power factor K Vibration acceleration Front Vibration acceleration Rear Power factor K 092 | 3/8" 90,8 dB(A) 101,8 dB(A) 1,0 dB(A) 4,7 m/s 5,6 m/s 1,5 m/s
Powerful and extremely heavy-duty Makita electric motor Ergonomic hand guard with non-slip coating Automatic oil pump for reliable chain lubrication Toolless chain tensioner Metal spike bar for effective force deflection Oil fill level window
Electric runout brake Electric overload protection Professional bar With 5m cable Initial current limiter
DOLMAR GmbH. A Member of the Makita Group www.dolmar.com