Parallel Beam Linear Sensor
Thru-beam Linear Sensor Featuring Space-saving Head and Easy-to-use Amplifier
Visible light ensures ease of optical axis adjustment for Standard Sensors. Sensor head for 10-mm model is one third the size of that used with earlier models such as the Z4LA. Digital display allows measured values to be read easily. Features hold functions, bank functions and functions for setting discrimination output according to the application. Connector cables between the Sensor and Amplifier and DIN Track mounting ensure easy installation. Side-view Attachment with 10-mm models also contributes to space saving.

Z4LB V2

Ordering Information

Sensors/Amplifiers

Sensors on Standard Models
Sensing distance Measurement width 10 mm

0 to 300 mm

Amplifiers on Standard Models
Model Z4LB-S10V2 Z4LB-S30V2 NPN model Z4LB-CV2 PNP model Z4LB-CPV2
One-side Interruption High-precision Models (Set for sensor and amplifier)

40 mm (fixed)

NPN models Z4LB-A1040V2 Z4LB-A3040V2
PNP models Z4LB-A1040PV2 Z4LB-A3040PV2
Accessories (Sold Separately)

Extension Cable

Application Connection between Sensor and Amplifier Note: Model Z49-C13 3m 8m Receiver Z49-F2D Length Vertical beam

Side-view Attachment

Application Emitter Model Z49-F2L
The Extension Cable comes in a set for receiver and emitter. When ordering, specify the length required as well as the model number.

Horizontal beam

Emitter

Z49-F3L

Receiver

Z49-F3D

Specifications

Ratings

Item Sensors Amplifiers/One-side Interruption Interr ption High-precision Models Light source (emission wavelength) Measurement width Sensing distance Minimum sensing object Response time (see note 1) Linear ea output t t Output voltage Resolution (see note 2) Linearity Temperature e eaue characteristic h t i ti Control outputs Discrimination outputs HIGH LOW HIGH, (PASS, NG) LD OFF input Timing input Forced zero input Forced-zero in ut Bank selection input Hold reset input Sensor Amplifier NPN models PNP models NPN models NPN Models PNP Models Standard Models (Separate Type) Z4LB-S10V2 Z4LB-S30V2 Z4LB-CV2 Z4LB-CPV2 One-side Interruption High-precision Models (Integrated Type) --Z4LB-A1040V2 Z4LB-A1040PV2 --Z4LB-A3040V2 Z4LB-A3040PV2
Visible-light semiconductor laser (Wavelength: 650 nm, IEC Class 1, FDA Class II) 10 mm 0 to 300 mm 0.1 mm dia. 0.2 mm dia. 0.3 or 5 ms (switch-selectable) 1 to 5 V (output impedance: 100 , allowable load resistance: 10 k min.) 5 m (5 ms), 10 m (0.3 ms) --0.1% F.S./C (see notes 4, 5) 0.02% F.S./C (see notes 4, 5) NPN open-collector outputs: 100 mA max. at 30 VDC Residual voltage: 1.2 V max. PNP open-collector outputs: 100 mA max. at 30 VDC Residual voltage: 2.0 V max. ON: 0 V short-circuited or 1.5 V max. OFF: Open (leakage current: 0.1 mA max.) ON: Power supply voltage short-circuited or power supply voltage 1.5 V max. OFF: Open (leakage current: 0.1 mA max.) Measured value display, hold, bank selection, discrimination outputs, scaling 12 to 24 VDC 10% ripple (p-p): 10% max. 200 mA max. 3,000 lx max. (incandescent lamp) Operating: 0 to 50C Storage: 15 to 60C (with no icing) Operating: 35% to 85% (with no condensation) Storage: 35% to 85% (with no condensation) 10 to 150 Hz, half-amplitude of 0.75 mm, acceleration of 100 m/s2 max. 10 to 150 Hz, half-amplitude of 0.15 mm, acceleration of 20 m/s2 max. 1,000 VAC, 50/60 Hz, 1 min 300 VAC, 50/60 Hz, 1 min IEC60529 IP40 Cable with connector (standard length of cable for Sensor: 2 m; standard length of cable for Amplifier: 2 m) Sensor: Diecast zinc, Amplifier: ABS Sensor/Oneside Interruption High-precision Model Amplifier Approx. 310 g
(emitter: approx. 110 g; receiver: approx. 105 g; includes 2-m cable)

10 mm 40 mm 0.1 mm dia.

30 mm 0.2 mm dia.
15 m (5 ms), 30 m (0.3 ms)
5 m (5 ms), 10 m (0.3 ms)
0.5% F.S. (see notes 3, 5)

Control inputs

PNP models
Main functions Power supply voltage Current consumption Ambient illumination Ambient temperature Ambient humidity Vibration ba o resistance i t Dielectric e ec c strength t th Sensor Amplifier Sensor Amplifier
Degree of protection Connection method Material Weight (including package) (see note 6)

Approx. 790 g

(emitter: approx. 230 g; receiver: approx. 195 g; includes 2-m cable)

Approx. 610 g

(Sensor: approx. 280 g; Amplifier: approx. 210 g; includes 2-m cable)

Approx. 900 g

(Sensor: approx. 510 g; Amplifier: approx. 210 g; includes 2-m cable)

Approx. 450 g

(Amplifier: approx. 210 g; includes 2-m cable)
--Instruction manual, label

Connecting bracket (Z4LB-A1040jV2 only)

Z4LB-S30V2 Z4LB-A3040jV2

LD ON indicator
Connecting bracket (Z4LB-A3040jV2 only)
Amplifier Z4LB-CjV2 Z4LB-A1040jV2 Z4LB-A3040jV2
Operating mode selector Display Gain adjuster (Z4LB-CjV2 only)
LD ON indicator HIGH/PASS indicator LOW/NG indicator TEACH Key OFF delay selector Right Key Response time selector Up Key Light/dark mode selector SET Key Measurement unit selector

Emitter connector

Receiver connector

Operation

Functions
Function Display functions LD ON indicator Display (with measurement unit selection and light/dark mode selection functions) Description Lights when laser beams are emitted. The Sensor and Amplifier indicators light at the same time. Displays either linear output voltage (V) or length (mm) according to the measurement unit selector switch setting. If the measurement unit is set to length (mm), set the measurement width to be used. The default setting is 10 mm. The amount of incident light or light interruption can be selected using the light/dark mode selector switch. HIGH/PASS indicator LOW/NG indicator Forced-zero indicator (displayed as the lowest decimal place) Output functions Linear output (with light/dark mode selection function) Lights when HIGH/PASS discrimination output turns ON. Lights when LOW/NG discrimination output turns ON. Lights when the forced-zero settings are enabled in RUN mode.
Outputs voltage (1 to 5 VDC) proportional to the amount of incident light or light interruption. The light/dark mode selector switch is used to select either light or dark mode. Dark mode Light mode
Linear output (V) Linear output (V) Amount of light interruption (mm)
Amount of incident light (mm)
HIGH/PASS output (with discrimination output setting and short-circuit protection functions)
One of the following discrimination output modes can be selected according to the application. HIGH/LOW Output Mode: Turns ON when measured value x HIGH threshold PASS/NG Output Mode: Turns ON when LOW threshold < measured value < HIGH threshold HIGH/LOW Inverted Output Mode: Turns ON when measured value y HIGH threshold The default setting is HIGH/LOW Output Mode. One of the following discrimination output modes can be selected according to the application. HIGH/LOW Output Mode: Turns ON when measured value y LOW threshold PASS/NG Output Mode: Turns ON when measured value x LOW threshold or measured value yHIGH threshold HIGH/LOW Inverted Output Mode: Turns ON when measured value x LOW threshold The default setting is HIGH/LOW Output Mode.
LOW/NG output (with discrimination output setting and short-circuit protection functions)
Function Input functions LD OFF input Description
Laser beams will be stopped when this input turns ON. ldoff appears on the display, and linear output, HIGH/LOW discrimination indicator and output remain in the previous state. All displays except the LD ON indicator and all outputs retain the previous values. Displays the measured value as zero when the unit is set to length (mm). The value is set if forced-zero input is ON for 0.2 to 0.8 s and cleared if it is ON for 1 s or more. To set forced-zero or clear forced-zero, press and hold down the SET Key for 3 s while in RUN mode.

Forced-zero input

Timing input
Forcibly turns OFF HIGH/PASS or LOW/NG discrimination output if this input turns ON during normal measurement. Controls sampling timing if this input turns ON during hold measurement. The default setting is normal.

Bank selection input

The Z4LB V2 has two banks in which thresholds can be set independently. If the bank selection input is enabled, the thresholds to be used for judgment can be switched. The default setting is disabled. Bank Bank 1 Bank 2 NPN type Open or connected to 12 to 24 VDC Connected to 0 V PNP type Open or connected to 0 V Connected to 12 to 24 VDC
Hold reset input Threshold setting g f ti function Direct setting Teaching setting
Resets the held value if this input turns ON during hold measurement. The thresholds are set to desired values by using the Right Key, Up Key, and SET Key. The thresholds are set to desired values by teaching. The HIGH threshold output turns ON when the HIGH threshold is equal to or below a measured value. The LOW threshold output turns ON when the LOW threshold is equal to or above a measured value.

Hold (See below)

Holds the display and output values. One of the following six hold methods can be selected according to the application: Peak hold, bottom hold, sample hold, peak-to-peak hold, self-peak hold, self-bottom hold. The default setting is normal. Specifies whether to back up the forced-zero set value. If the value is to be retained after the Sensor is turned OFF, always enable the backup. The default setting is enabled. The resolution changes with the response time. Select the required response time, taking the resolution into consideration. Switch FAST SLOW Response time 0.3 ms 5 ms

Backup

Response time selection
OFF delay Gain adjustment (for standard model only)
The HIGH/LOW discrimination outputs will have a 40-ms OFF delay if the OFF delay selector is set to ON. Adjusts the full scale of linear output and display.
Function Settings with Keys
Press TEACH+SET Keys for 3 s. Press TEACH Key for 3 s.

Measurement width

10 hl1 pass hl2

Discrimination outputs

Hysteresis setting

Display unit: V

Display unit: mm

00.050

Run mode
norml ph bh sh pph sph sbh
Display unit: V Display unit: mm

1.000 1.000

00.000 00.000

Bank selection

off on on off
All set value initialized
Initialization * Shaded settings are the default settings.

Z4LB V2 Hold Functions

Normal
Measurement is performed continuously and measurement results are displayed and output.
Peak Hold and Bottom Hold
The maximum or the minimum value while the timing input is ON is displayed, output, and held. The discrimination outputs are controlled according to the displayed value and output value. Displayed value (Output) Measured value

Sampling Timing input

Sampling
The discrimination outputs are not turned OFF when the timing input turns ON.
Display during this period:
The measured value is output as a linear output. Power ON or hold reset input

Sample Hold

The current value when the timing input turns ON is displayed, output, and held. The discrimination outputs are controlled according to the displayed value and output value. Displayed value (Output) Measured value
Timing input The discrimination outputs are not turned OFF when the timing input turns ON.

Peak-to-peak Hold

The difference between the maximum and minimum values while timing input is ON is displayed, output, and held. The discrimination outputs are controlled according to the displayed value and output value. Displayed value (Output) Measured value
Power ON or hold reset input
The measured value is output as a linear output.
Self-peak Hold and Self-bottom Hold
The maximum value (self-peak hold) or the minimum value (self-bottom hold) while the measured value is equal to or greater than the trigger level (self-peak hold), or is equal to or smaller than the trigger level (self-bottom hold), is displayed, output, and held. The discrimination outputs are controlled according to the displayed value and output value. Note: No sampling is performed when the timing input is ON. Displayed value (Output) Measured value

Trigger level

Z4LB V2 I/O Stage Circuit Diagrams
NPN Models Standard Model: High-precision Models: Z4LB-CV2 Z4LB-AjjV2
Brown 100 Black Shield 1- to 5-V linear output Linear output GND 12 to 24 VDC
White HIGH/PASS output Load Internal circuits Gray LOW/NG output
Blue 0 V Pink Purple Red Orange/Purple Green Bank selection input LD OFF input Timing input Hold reset input Forced-zero input

30 VDC max.

PNP Models Standard Model: High-precision Models:

Z4LB-CPV2 Z4LB-AjjPV2

White HIGH/PASS output Load Gray LOW/NG output Internal circuit
Blue 0 V Pink Purple Red Orange/Purple Green Bank selection input Hold reset input Forced-zero input LD OFF input Timing input

Dimensions

Note: All units are in millimeters unless otherwise indicated.

Sensor Z4LB-S10V2

Two, MPhilips pan head screws Vinyl insulated round cable, 4 dia. Standard length: 2 m

11.5 dia.

Two, MPhilips pan head screws Optical axis Optical axis Vinyl insulated round cable, 4 dia. Standard length: 2 m

14.7 dia.

Connector Two, M3 Effective screw depth: 3

4 dia.

Lens (137)
Slit (101) 4 dia. Two, M3 Effective screw depth: 3

Connector

Mounting Hole Cutout Dimensions

Two, M3 Two, M3

Two, Hexagonal nuts

Sensor Z4LB-A1040jV2

Vinyl insulated round cable, 4 dia. Standard length: 2 m

Optical axis

Two, 4.4-dia. holes 11 dia. spot facing depth: 5 Beam
Connector Emitter side Optical axis Receiver side

Two, M4

Sensor Z4LB-S30V2

Two, 4.5 dia.

Vinyl insulated round cable 4 dia. Standard length: 2 m
Three, MPhilips pan head screws
Vinyl insulated round cable 4 dia. Three, MStandard length: 2 m Philips pan head screws
Two, M3 Effective screw depth: 5

Lens (836)

Slit (130)
Two, M4 11.5 dia. 14.7 dia. Two, M4

Sensor Z4LB-A3040jV2

Two, 4.4-dia. holes 11 dia. spot facing depth: 5

Receiver side

Emitter side
Gain adjuster (There is no gain adjuster on Z4LB-A1040jV2 or Z4LB-A3040jV2 models.)
10-conductor, vinyl insulated round cable, 5.8 dia. (conductor cross-sectional area: 1.63 mm2, insulation: 1.1 mm dia.) Standard length: 2 m

Two mounting holes

Side-view Attachment Vertical Beam Z49-F2L (For Emitter)
Emitted beam region Optical axis

Two, M2 4

Side-view Attachment Vertical Beam Z49-F2D (For Receiver)
Sensing region Optical axis
Side-view Attachment Horizontal Beam Z49-F3L (For Emitter)
Side-view Attachment Horizontal Beam Z49-F3D (For Receiver)

Sensing region

Installation

Wiring

Brown Blue White Gray Black Shield Green Purple Red Orange/Purple Pink Note: 12 to 24 VDC 0V HIGH/PASS output LOW/NG output Linear output (1 to 5 V) Linear GND (see note 3) Bank selection input Timing input Hold reset input Forced-zero input LD OFF input
1. When particularly high resolutions are required, prepare a separate, stable power supply. 2. Perform wiring correctly. Failure to do so may result in damage to the Sensor. In particular, ensure that the wire for linear output does not come into contact with other wires. 3. 0 V (blue) and linear GND (shield) are connected internally passing through a resistance. Use the blue one (0 V) to supply power, and use the shielded wire (linear GND) together with the black wire (linear output) for linear output.

Precautions

Designing the Setup

Compatibility

There is general compatibility between Sensors and Amplifiers for standard models. However, the emitters and the receivers are inspected as sets before delivery. Operation is possible using the emitters or the receivers from other sets, but in order to satisfy specifications, the serial number of the emitter and the receiver must be the same. With high-precision models, the Sensor and the Amplifier are adjusted as a set. Only use combinations with the same serial number.

Environment

Do not use the Sensor in strong electromagnetic fields or in an environment where the operation of the Sensor is subject to the reflection of intense light (such as other laser beams or electric arc-welding machines.) The Sensor may not be able to accurately detect objects of certain materials or shapes.
Mounting the Side-view Attachment
Handling Precautions Do not apply excessive shock to the Attachment. Doing so may result in damage. The Attachment can be used attached to either the emitter or the receiver, but not both.

Mutual Interference

Operation is possible with two or more Sensors mounted together, but operation is not possible with two or more beams in close proximity. If the Sensor is used in this way, it may cause malfunction.

Wiring Precautions

Wiring and Power Supply
Do not impose voltage exceeding the rated voltage, otherwise the Sensor may be damaged. When supplying power to the Sensor, make sure that the polarity of the power is correct, otherwise, the Sensor may be damaged. Do not short-circuit the load supplied with open collector output, otherwise the Sensor may be damaged. Do not lay a power supply cable for the Z4LB V2 together with highvoltage lines or power lines to prevent interference, damage, and malfunction. The Z49-C13 Extension cable (3 or 8 m in length) can be connected to the Sensor cable or Amplifier cable. The total length of the Sensor cable or Amplifier cable, however, must be 10 m or less. Use a shielded cable to extend the Amplifier cable, in which case, a shielded cable that is the same as that of the Amplifier cable must be used. Use an isolation transformer for the power supply of the Z4LB V2 as shown in the following. Do not use an autotransformer (single-winding transformer). Incorrect Autotransformer + Z4LB V2

Commercial power supply

Mounting Precautions Do not touch any internal parts when mounting. Dirt inside the Attachment may affect the high-performance reflective mirror inside and cause malfunction. When mounting the Attachment, tighten the mounting screws to a torque not exceeding 0.2 N S m.
Correct Isolation transformer

+ Z4LB V2

Other Precautions

Maintenance

Install the Sensor in a clean environment and keep the filter on the front panel of the Sensor free from oil and dust. If affected by oil or dust, clean the filter as follows: 1. Use a blower brush (used to clean camera lenses) to blow large dust particles from the surface. Do not blow the dust away with your mouth. 2. Use a soft cloth (for lenses) with a small amount of alcohol to remove the remaining dust. Note: Do not use a scrubbing action when cleaning as scratches on the filter could result in the Sensor malfunctioning.

Laser Safety

The Z4LB V2 Parallel Beam Linear Sensor, is a Class 1 Laser Product according to EN60825-1 (IEC825-1) and a Class II Laser Product according to FDA (21 CFR1040.10) (see note). The Z4LB V2 is meant to be built into final system equipment. Pay special attention to the following precautions for the safe use of the product: Note: Europe: Class 1 of EN60825-1: 1994 = IEC825-1: 1993 U.S.A.: Class II of FDA (21 CFR1040.10)
1. Use this product as specified in this datasheet. Otherwise, you may be exposed to hazardous laser radiation. 2. Be careful not to expose your eyes directly to the laser radiation or indirectly to laser radiation reflected from mirror or shiny surfaces. 3. To avoid exposure to hazardous laser radiation, do not displace nor remove the protective housing during operation, maintenance, and any other servicing. 4. The user should return the product to OMRON for all repair and servicing. 5. As for other countries, observe the regulations and standards specified by each country.
Requirements from Regulations and Standards
EN60825-1 Safety of Laser Products, Equipment Classification, Requirements and Users Guide
Summary of Manufacturers Requirements Requirements; equ e e s S b l Sub-clause Description of hazard class Classification Class 1 Safe under reasonably foreseeable conditions Class 2 Low power; eye protection normally afforded by aversion responses Class 3A Same as Class 2. Direct intrabeam viewing with optical aids may be hazardous Class 3B* Direct intrabeam viewing may be hazardous Class 4 High power; diffused reflection may be hazardous

Protective housing Safety interlock in protective housing Remote control Key control Emission warning device Attenuator Location controls Viewing optics Scanning Class label Aperture label Service entry label Override interlock label User information Purchasing and service information Medical products Fibre optic *
Required for each laser product; limits access necessary for performance of functions of the products Designed to prevent removal of the panel until accessible emission values are below the AEL for the class assigned Not required Not required Not required Permits easy addition of external interlock in laser installation Laser inoperative when key is removed Gives audible or visible warning when laser is switched on or if capacitor bank of pulsed laser is being charged Gives means beside ON/OFF switch to temporarily block beam Controls so located that there is no danger of exposure to AEL (see note 2) above Classes 1 or 2 when adjustments are made.
Not required Not required
Emission from all viewing systems must be below Class 1 AELs as applicable Scan failure shall not cause product to exceed its classification Required wording Not required Figures A and B and specified wording Specified wording required
Required as appropriate to the class of accessible radiation Required under certain conditions as appropriate to the class of laser used Operation manuals must contain instructions for safe use Promotion brochures must reproduce classification labels; service manuals must contain safety information Special calibration instructions required Special calibration instructions, means for measurement and target-indicator required
Cable service connections require tool to disconnect if disconnection breaks protective housing and permits access above Class 1
With respect to the requirements of remote interlock connector, key control, emission warning and attenuator, Class 3B laser products not exceeding five times the AEL of Class 2 in the wavelength range of 400 nm to 700 nm are to be treated as Class 3A laser products. 1. This table is intended to provide a convenient summary of requirements. See text of this standard for complete requirements. 2. AEL: Accessible Emission Limit The maximum accessible emission level permitted within a particular class. For your reference, see ANSI Z136.1-1993, Section 2.
Symbol and border: black Background: yellow Legend and border: black Background: yellow
Figure A Warning label Hazard symbol FDA (Compliance Guide for Laser Products, 1985, according to 21 CFR1040.10) Requirements equ e e s I Performance (all laser products) Protective housing Safety interlock Location of controls Viewing optics Scanning safeguard Remote control connector Key control Emission indicator Beam attenuator Reset Medical Surveying, leveling, alignment Demonstration R (see note 2) R (see notes 3, 4) N/A R R N/A N/A N/A N/A N/A S S S R (see note 2) R (see notes 3, 4) R R R N/A N/A N/A N/A N/A S S S R D (see note 5) N/A R (see note 6) R R R R (see note 2) R (see notes 3, 4) R R R N/A N/A R R N/A S S S R D (see note 5) R R (see note 7) R R R R R N/A N/A R R N/A IIa

Figure B Explanatory label
Class (see note 1) II IIIa R (see note 2) R (see notes 3, 4) IIIb R (see note 2) R (see notes 3, 4) R R R R R R (see note 10) R N/A S (see note 8) NP S (see note 11) R D (see note 5) R R (see note 12) R R R IV R (see note 2) R (see notes 3, 4) R R R R R R (see note 10) R R (see note 13) S (see note 8) NP (see note 11) R D (see note 5) R R (see note 12) R R R
Performance (laser systems)
Performance (specific purpose products) S (see note 8) S S R D (see note 5) R R (see note 9) R R R
Labeling (all laser products) Certification & identificaR tion Protective housing Aperture Class warning User information Product literature Service information Abbreviations: D (see note 5) N/A N/A R N/A R
Information (all laser products)
R: Required. N/A: Not applicable. S: Requirements: Same as for other products of that Class. Also see footnotes. NP: Not permitted. D: Depends on level of interior radiation. Footnotes: 1. Based on highest level accessible during operation. 2. Required wherever & whenever human access to laser radiation above Class I limits is not needed for product to perform its function. 3. Required for protective housings opened during operation or maintenance, if human access thus gained is not always necessary when housing is open. 4. Interlock requirements vary according to Class of internal radiation. 5. Wording depends on level & wavelength of laser radiation within protective housing.
6. Warning statement label. 7. CAUTION logotype. 8. Requires means to measure level of laser radiation intended to irradiate the body. 9. CAUTION if 2.5 mW cm2 or less, DANGER if greater than 2.5 mW cm2. 10.Delay required between indication & emission. 11. Variance required for Class IIb or iV demonstration laser products and light shows. 12.DANGER logotype. 13.Required after August 20, 1986.

Use Precautions

EN60825-1 Requirements; equ e e s S b l Sub-clause Remote interlock Key control Beam attenuator Emission indicator device Warning signs Beam path Specular reflection Eye protection Protective clothing Training * Classification Class 1 Not required Not required Not required Not required Not required Not required No requirements No requirements No requirements No requirements Terminate beam at end of useful length Prevent unintentional reflections Required if engineering and administrative procedures not practicable and MPE exceeded Sometimes required Specific requirements Class 2 Class 3A Class 3B* Remove key when not in use When in use prevents inadvertent exposure Indicates laser is energized Follow precautions on warning signs Class 4 Connect to room or door circuits

Required for all operator and maintenance personnel
With respect to the requirements of remote interlock connector, key control, beam attenuator, and emission indicator, Class 3B laser products not exceeding five times the AEL of Class 2 in the wavelength range of 400 nm to 700 nm are to be treated as Class 3A laser products. This table is intended to provide a convenient summary of requirements. See text of this standard for complete precautions.
ANSI Z136.1:1993 American National Standard for the Safe Use of Lasers Control Measures for the Four Laser Classes Control measures Engineering Controls Protective Housing (4.3.1) Without Protective Housing (4.3.1.1) Interlocks on Protective Housing (4.3.2) Service Access Panel (4.3.3) Key Control (4.3.4) Viewing Portals (4.3.5.1) Collecting Optics (4.3.5.2) Totally Open Beam Path (4.3.6.1) Limited Open Beam Path (4.3.6.2) Enclosed Beam Path (4.3.6.3) Remote Interlock Connector (4.3.7) Beam Stop or Attenuator (4.3.8) Activation Warning Systems (4.3.9) Emission Delay (4.3.9.1) Indoor Laser Controlled Area (4.3.10) Class 3b Laser Controlled Area (4.3.10.1) Class 4 Laser Controlled Area (4.3.10.2) Laser Outdoor Controls (4.3.11) Laser in Navigable Airspace (4.3.11.2) ----MPE --------MPE ------MPE MPE ------MPE MPE ----1 X 2a X 2 X Classification 3a X 3b X X X S MPE MPE X NHZ X NHZ S S S --X NHZ X --X NHZ S 4 X X X X MPE MPE X NHZ X NHZ X X X X X NHZ --X X NHZ S
LSO (see note 2) shall establish Alternate Controls
None is required if 4.3.1 and 4.3.2 fulfilled ----------------------------------------------------------------------S
Control measures Temporary Laser Controlled Area (4.3.12) Remote Firing & Monitoring (4.3.13) Labels (4.3.14 and 4.7) Area Posting (4.3.15) Administrative & Procedural Controls Standard Operating Procedures (4.4.1) Output Emission Limitations (4.4.2) Education and Training (4.4.3) Authorized Personnel (4.4.4) Alignment Procedures (4.4.5) Protective Equipment (4.4.6) Spectator (4.4.7) Service Personnel (4.4.8) MPE Demonstration with General Public (4.5.1) Laser Optical Fiber Systems (4.5.2) Laser Robotic Installations (4.5.3) Eye Protection (4.6.2) Protective Windows (4.6.3) Protective Barriers and Curtains (4.6.4) Skin Protection (4.6.5) Other Protective Equipment (4.6.5) Warning Signs and Labels (4.7) (Design Requirements) Service and Repairs (4.8) MPE MPE ----------MPE --MPE ----------MPE X MPE ----------MPE X MPE ----------X X X NHZ S MPE X NHZ S X MPE X NHZ Classification --MPE --X --1 --------------MPE --X --2a --------------MPE --X --2 ----S --X ----MPE --X S 3a --S --X ------X X NHZ 3b S X X X S S X S
X X NHZ 4 X X X X X X X X X X NHZ X MPE X NHZ S X MPE X NHZ

LSO Determination

Use may be required ----S S
Modification of Laser Systems (4.9) LSO Determination Note: 1. LEGEND X: Shall S: Should ---: No requirement : Shall if enclosed Class 3b or Class 4 MPE: Shall if MPE is exceeded NHZ: Nominal Hazard Zone analysis required : Applicable only to UV and IR Lasers (4.5.1.2) 2. LSO: Laser Safety Officer An individual shall be designated the Laser Safety Officer with the authority and responsibility to monitor and enforce the control of laser hazards, and to effect the knowledgeable evaluation and control of laser hazards. For your reference, see ANSI Z136.1-1993, Section 1.3.

Laser Product Classifications
Class Class 1 Class 2 Class 3A Description Lasers which are safe under reasonably foreseeable conditions of operation. Lasers emitting visible radiation in the wavelength range from 400 nm to 700 nm. Eye protection is normally afforded by aversion responses including the blink reflex. Lasers which are safe for viewing with the unaided eye. For laser emitting in the wavelength range from 400 nm to 700 nm, protection is afforded by aversion responses including the blink reflex. For other wavelengths the hazard to the unaided eye is no greater than for Class 1. Direct intrabeam viewing of Class 3A lasers with optical aides (e.g., binoculars, telescopes, microscopes) may be hazardous. Direct intrabeam viewing of these lasers is always hazardous. Viewing diffuse reflections is normally safe (see note). Lasers which are also capable of producing hazardous diffuse reflections. They may cause skin injuries and could also constitute a fire hazard. Their use requires extreme caution.

Class 3B Class 4

Conditions for safe viewing of diffuse reflections for Class 3B visible lasers are: minimum viewing distance of 13 cm between screen and cornea and a maximum viewing time of 10 s. Other viewing conditions require a comparison of the diffuse reflection exposure with the MPE.
Comparison of Classifications between FDA and ANSI
Class Class I/1 FDA definition Limits applicable to devices that have emissions in the ultraviolet, visible, and infrared spectra, and limits below which biological hazards have not been established. ANSI description A Class 1 laser is considered to be incapable of producing damaging radiation levels during operation and maintenance and is, therefore, exempt from any control measures or other forms of surveillance. Class 2 lasers are divided into two subclasses, 2 and 2a. A Class 2 laser emits in the visible portion of the spectrum (0.4 to 0.7 m) and eye protection ( ) y is i normally afforded by the aversion response i ll ff d d b th i including the blink reflex.

Class IIa/2a

Limits applicable to products whose visible emission does not exceed Class I limits for emission durations of 1,000 seconds or less and are not intended for viewing. Limits applicable to products that have emissions in the visible spectrum (400 to 710 nm) for emission durations in excess of 0.25 second, providing that emissions for other durations and/or wavelengths do not exceed the Class I limits. Class II products are considered hazardous for direct long-term ocular exposure. Limits to products that have emissions in the visible spectrum and that have beams where the total collectable radiant power does not exceed 5 milliwatts. Limits applicable to devices that emit in the ultraviolet, visible, and infrared spectra. Class IIIb products include laser systems ranging from 5 to 500 milliwatts in the visible spectrum. Class IIIb emission levels are ocular hazards for direct exposure throughout the range of the Class, and skin hazards at the higher levels of the Class. Exceeding the limits of Class IIIb and are a hazard for scattered reflection as well as for direct exposure.

Class II/2

Class IIIa/3a

Class IIIb/3b

Class 3 lasers are divided into two subclasses, 3a and 3b. A Class 3 laser may be hazardous under direct and specular reflection viewing conditions, g , but the diffuse reflection i usually not a h b t th diff fl ti is ll t hazard. d

Class IV/4

A Class 4 laser is a hazard to the eye or skin from the direct beam and sometimes from a diffuse reflection and also can be fire hazard. Class 4 lasers may also produce laser-generated air contaminants and hazardous plasma radiation.

Label Indications

Note: FDA
Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure. Z4LB-S10V2 Z4LB-A1040jV2 FDA Certification Label Z4LB-S30V2 Z4LB-A3040jV2 FDA Certification Label FDA Laser Aperture Label
FDA Caution Label FDA Laser Aperture Label FDA Laser Aperture Label FDA Caution Label FDA Caution Label FDA Certification Label

44 650

Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure.
The product has been produced at OMRON Ayabe which obtained ISO9001-approval for its quality system and ISO14001-approval for its environmental management system from international certification bodies.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Cat. No. F051-E1-1A

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company Industrial Sensors Division Sensing Devices and Components Division H.Q. 28th Fl., Crystal Tower Bldg., 1-2-27, Shiromi, Chuo-ku, Osaka 540-6028 Japan Tel: (81)6-6949-6012/Fax: (81)6-6949-6021 Printed in Japan 0400-1M (1099) a

Direct solenoid and solenoid pilot operated valves

Series 200

Individual mounting
inline inline hazardous location

Series

Manifold mounting
sub-base non plug-in sub-base with pressure regulators sub-base hazardous location

Manual operator

Sealed solenoid enclosure

Armature

Solenoid push pin
Spring biased moveable pole piece

2 CYL 1 N.C.

700 900

3 N.O.

Balanced poppet

Valve spring

SERIES FEATURES
800 ISO 1 ISO 2 ISO 3 MAC 125A MAC 250A MAC 500A
The patented MACSOLENOID with its non-burn out feature on AC service. Six valve functions with one Inline valve and four valve functions with one Manifold valve. A triple rated coil for 120/60, 110/50 or 24 VDC (6 Watt). Inline & add-a-unit manifold capability. Use on lube or non-lube service. Extremely rapid response and cycle rate. Various types of manual operators and electrical enclosures. Extremely long service life. Optional low wattage DC solenoids down to 1 watt.
Consult Precautions page 364 before use, installation or service of MAC Valves

OF PRODUCTION TESTED

MONTHS

WARRANTY

APPLICATION CONVERSION PROCEDURE:
3-ways and 2-ways. Changes within a stack from one function to another can be made without disturbing the plumbing.

SPECIAL APPLICATIONS:

INDIVIDUAL MODELS The balanced poppet design facilitates using the same valve for 6 functions with any port being connected to vacuum, pressure or plugged. Piping is shown in the chart below. MANIFOLD MODELS The interchangeable function plate between the valve body and base permits selection for 2- or 3-way, Normally Closed or Normally Open operation, instead of through piping as shown below in the Inlines. On 3-way applications, one function plate is used for both N.C. and N.O. When "3-C" is visible on the plate, the function will be N.C. When "3-O" is visible, the function is N.O. On 2-way applications, a separate plate is used and like the 3-way plate is marked "2-C" for N.C. and "2-O" on the other side for N.O. The 2-way plates block the exhaust at the valve, permitting the mixing in a stack of
PIPING CHART FOR INDIVIDUAL MODELS
N.C. ONLY MODELS A single purpose Normally Closed Only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. EXPLOSION PROOF MODELS These models are designed to meet U.L. and C.S.A. standards for Division 1, Class I, Groups B, C, D and Class II, Groups E, F and G (NEMA equivalent to Class I is NEMA 7; Class II is NEMA 9). Explosion proof models are available in either inline or manifold versions but only with the no operator ("O") manual operator.

PLUGGED 3

3 Way Normally Closed

2 Way Normally Closed

Selector

P L 1 U G G E D

3 Way Normally Open

2 Way Normally Open

Divertor
Supply Operator De-Energized Operator Energized

Function

3/2 NO-NC, 2/2 NO-NC

OPERATIONAL BENEFITS

Port size

1/8 - 1/4

Flow (Max)

0.5 Cv

inline
1. Balanced poppet, immune to variations of pressure. 2. Short stroke with high flow. 3. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Manual operator standard on all valves. 6. Burn-out proof solenoid on AC service.

HOW TO ORDER

Universal valve

NC only valve

1/8 NPTF 1/4 NPTF

224B-XXYZZ 225B-XXYZZ

274B-XXYZZ 275B-XXYZZ

SOLENOID OPERATOR

XX Y ZZ *

Voltage

120/60, 110/50, 24 VDC (6.0 W) 240/60, 220/50 24/60, 24/VDC (2.5 W) 24 VDC (24.0 W) 24 VDC (8.5 W)

Non-locking Locking

JA JC BA CA

Electrical connection

Square connector Square connector with light Flying leads (18) Conduit 1/2 NPS
ISO 1 ISO 2 ISO 3 MAC 125A MAC 250A MAC 500A
* Other options available, see page 357. Notes: CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN Individual inline valves can be changed from normally closed to normally open by connecting the inlet to port 3 instead of port 1. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above.

100% 100%

technical data

WARRANTY MONTHS

Fluid : Pressure range : Lubrication : Filtration : Temperature range : Flow (at 6 bar, P=1bar) : Leak rate : Coil : Voltage range : Protection : Power : Response times :
Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180F and 210F) 40 0F to 140F (-18C to 60C) 0.5 Cv General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush : 33 VA = 1 to 24 W 24 VDC (8.5 W) 120/60 Energize : 15 ms Energize : 3-8 ms De-energize : 5 ms De-energize : 3-13 ms Holding : 19.7 VA

S pare parts : Options :

Solenoid operator (power 6 W) : D4-XXAAB, cover mounting screws 32222 and seal B5-6001. BSPP threads.

dimensions

Dimensions shown are metric (mm)
99.2 5.1 DIA.-THRU TYP.(2) 27.83 TYP.(2)
38.6 TYP. (2) 34.6 5.29 45.2 88.6
inline hazardous location
1. Balanced poppet, immune to variations of pressure. 2. Short stroke with high flow. 3. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Burn-out proof solenoid on AC service.

224B-XX0EA 225B-XX0EA

274B-XX0EA 275B-XX0EA
120/60, 110/50, 24 VDC (6.0 W) 240/60, 220/50 24/60, 24/VDC (6.0 W) 12 VDC (6.0 W) 12 VDC (9.5 W) 24 VDC (8.5 W)
Notes: The special version of the 200 Series designed for hazardous locations has been approved by CSA for Class I, Groups B, C & D; Class II, Groups E, F & G. Maximum rated fluid and ambient temperature is 40C; maximum pressure is 150 p.s.i. Approval is limited to certain common AC & DC voltages which are those designated in the table above. These valves are supplied without manual operators. This version of the 200 Series can be supplied on the standard individual inline or the manifold valve body assemblies. It can also be supplied as a pilot for the 57, 58 and 59 Series (with special adapter plate # M-00012). CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN Individual inline valves can be changed from normally closed to normally open by connecting the inlet to port 3 instead of port 1. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above.

Fluid : Pressure range : Lubrication : Filtration : Temperature range : Leak rate : Coil : Voltage range : Protection : Power : Response times :
Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180F and 210F) 40 0F to 104F (-18C to 40C) 1 General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage NEMA 7, NEMA 9; Class I Groups B, C & D; Class II Groups E, F & G. Inrush : 33 VA = 1 to 24 W 24 VDC (8.5 W) 120/60 Energize : 15 ms Energize : 3-8 ms De-energize : 5 ms De-energize : 3-13 ms Holding : 19.7 VA
Solenoid operator (power 6 W) : D4-XXAAB. Adapter plate assy. : A3-0506. BSPP threads.

1/2" NPSM CONDUIT

ADAPTER PLATE

5.1 DIA. 2 MTG HOLES

sub-base non plug-in

IN EXH

Valve less base 1/8 base NPTF 1/4 base NPTF
250B-XXYZZ 256B-XXYZZ 257B-XXYZZ
280B-XXYZZ 286B-XXYZZ 287B-XXYZZ

JC JA BA CA

Square connector with light Square connector Flying leads (18) Conduit 1/2 NPS

6300 6500

* Other options available, see page 357. End plate kit required (Port size : 1/4) : A2-5003-01.

OPTIONS

26XB-XXYZZ

- universal 2-way

(Base only - 1/8)

(Base only - 1/4)

6600 1300
CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN For manifold base mounted valves a plate is provided between the valve and the base. Three plates are available; a reversible plate for 3 Way valves (N.C. & N.O.), one plate for 2 Way N.C. and one for 2 Way N.O. Appropriate plates, determined by the valve model number, are supplied automatically with the valve. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above.
Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180F and 210F) 40 0F to 140F (-18C to 60C) 0.5 Cv 100 cm3/min General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush : 33 VA = 1 to 24 W 24 VDC (8.5 W) 120/60 Energize : 15 ms Energize : 3-8 ms De-energize : 5 ms De-energize : 3-13 ms Holding : 19.7 VA

S pare parts :

Solenoid operator (power 6 W) : D4-XXAAB, cover mounting screws 32222 and seal B5-6001. Function plate : A2-7005. Seal between bases : B5-5010. Tie-rod (x2) : B4-9004. BSPP threads. Explosion-proof model. Isolation of inlet : Mod. 313P. Isolation of exhaust : Mod. 313E. Additional bottom inlet : Mod. 0210. Bottom cyl. port : Mod. 0009. All bottom & side ports : Mod. 0004. Specify Mod. number after valve model number (i.e. 257B-111BA Mod. 0210)

1/8 OR 1/4 CYL PORT

Options :

Note :

OPTIONAL 1/8 OR 1/4 BOTTOM PORTS 1/4 INLET & EXH. PORTS EACH END MTG SLOT 8,1 DIA. MAX.

0.4 Cv

sub-base with pressure regulators
1. Balanced poppet, immune to variations of pressure. 2. Short stroke with high flow. 3. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Manual operator standard on all valves. 6. Burn-out proof solenoid on AC service. 7. Individual pressure control to each cylinder port.
Valve less base 1/4 base NPTF

250B-XXYZZ 252B-XXYZZ

280B-XXYZZ 282B-XXYZZ
* Other options available, see page 357. Manifold fastening kit required : N-02003 MODEL 252B3-Way N.C. or N.O. 262B2-Way N.C. or N.O. 282B3-Way N.C. only INDIVIDUAL PRESSURE CONTROL TO EACH CYLINDER PORT In this version the common inlet pressure supplies each individual valve in the stack. This common pressure passes through a relieving type regulator mounted on the same base as the valve and is supplied through the function plate to the Normally Closed or Normally Open poppet position. Through use of the appropriate function plate on the 200 Series basic valve, the operation can be Normally Closed Or Normally Open, 3-way or 2-way except for 282B models which are Normally Closed only. The exhaust ("out") port is common. Operation of the valves then opens or closes the cylinder port (See schematic diagram next page).
Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180F and 210F) 40 0F to 140F (-18C to 60C) 0.4 Cv 100 cm3/min General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush : 33 VA = 1 to 24 W 24 VDC (8.5 W ) 120/60 Energize : 15 ms Energize : 3-8 ms De-energize : 5 ms De-energize : 3-13 ms Holding : 19.7 VA

Solenoid operator (power 6 W) : D4-XXAAB, cover mounting screws 32222 and seal B5-6001. Function plate : A2-7005. Seal between bases (x2) : 17016-01. Tie-rod (x2) : B4-9004. Pressure regulator : PR02A-A0AA. BSPP threads. Explosion-proof model. Isolation of inlet and/or exhaust. Mod. PR80 (0-80 pressure range), Mod PR30 (0-30 pressure range)
128.9 1/2" NPS CONDUIT 110.5

5.7 DIA. MTG HOLE

1/8" NPTF GAUGE PORT

20.5 51.5 65.0

1/4" NPTF
1/4" NPTF IN & EXH. PORTS BOTH ENDS
EXHAUST ("OUT")

("OUT")

INLET ("IN")
("IN") SCHEMATIC 3-VALVE STACK
Inlet & outlet port size
1. Balanced poppet, immune to variations of pressure. 2. Short stroke with high flow. 3. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Manual operator standard on all valves. 6. Burn-out proof solenoid on AC service. 7. Selected pressure control to a single outlet.

251B-XXYZZ

* Other options available, see page 357. Manifold fastening kit required : N-02003 MODEL 251B3-Way Normally Closed SELECTED PRESSURE CONTROL TO A SINGLE OUTLET This version permits the alternate selection of any of the regulated pressures in the stack to one common outlet. With all valves de-energized the regulated pressure supplied to the Normally Open pressure port passes through the valves and out the corresponding port at the other end of the stack (Common Outlet Port). Pressure supplied to the common inlet port is regulated at each valve and blocked by the poppet of each valve. When a valve is shifted in the stack the Normally Open pressure is blocked and the regulated normally closed pressure of that valve is open to the common outlet. If two valves are energized at the same time the pressure at the common outlet would be that of the energized valve nearest the outlet. If the normally open pressure port is not used it is open to exhaust from the common outlet. The individual cylinder port in each base is non-operative. (See schematic diagram next page).

ddimensionss imension

1/2" NPS CONDUIT 110.5
EXHAUST OR N.O. OPTIONAL PRESSURE ("OUT")

SOL SOL SOL

COMMON OUTLET ("OUT")
COMMON SUPPLY ("IN")

SCHEMATIC 3-VALVE STACK

("IN")

sub-base hazardous location
250B-XX0EA 258B-XX0EA 259B-XX0EA
280B-XX0EA 288B-XX0EA 289B-XX0EA

82 6300

208 209
End plate kit required (Port size : 1/4) : A2-5003-01.

26XB-XX0EA

Notes: The special version of the 200 Series designed for hazardous locations has been approved by CSA for Class I, Groups B, C & D; Class II, Groups E, F & G. Maximum rated fluid and ambient temperature is 40C; maximum pressure is 150 p.s.i. Approval is limited to certain common AC & DC voltages which are those designated in the table above. These valves are supplied without manual operators. This version of the 200 Series can be supplied on the standard individual inline or the manifold valve body assemblies. It can also be supplied as a pilot for the 57, 58 and 59 Series (with special adapter plate # M-00012). CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN For manifold base mounted valves a plate is provided between the valve and the base. Three plates are available; a reversible plate for 3 Way valves (N.C. & N.O.), one plate for 2 Way N.C and one for 2 Way N.O. Appropriate plates, determined by the valve model number, are supplied automatically with the valve. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above.
Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180F and 210F) 40 0F to 140F (-18C to 60C) 0.5 Cv 100 cm3/min General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush : 33 VA = 1 to 24 W 24 VDC (8.5 W ) 120/60 Energize : 15 ms Energize : 3-8 ms De-energize : 5 ms De-energize : 3-13 ms Holding : 19.7 VA
Solenoid operator (power 6 W) : D4-XXAAC-0EA. Function plate : A2-7005. Seal between bases : B5-5010. Tie-rod (x2) : 19598. BSPP threads. Isolation of inlet : Mod. 313P. Isolation of exhaust : Mod. 313E. Additional bottom inlet : Mod 0210.

R4.0 TYP. (2)

127.8 122.9 118.0
35.6 TYP. (2) 142.7 94.5 52.9

72.8 92.7

20.1 TYP. (2)
Codification table for voltages / Manual operator / Electrical connection / Wire length

VALVE CODE

- XX Y ZZ (-VV) 3 4

OPTIONS AVAILABLE FOR

- valves type 100 Series - pilot valves "CNOMO"

- valves type 200 Series

- Pilot operated valves with pilots type 100 Series Series : 55 - 56 - 700 - 800 - 900 - 6300 - 6500 - 6600 - 1300 - ISO 1 - ISO 2 - ISO 3. - MAC 125 - MAC 250 - MAC 500

- pilot operated valves with pilots type 200 Series Series : 200 - 57 - 58 - 59.
- Pilot operated valves with pilots "CNOMO" Series : ISO1 - ISO2 - ISO3
Used on valve series: 100, 55, 56, 700, 800, 900, 6300, 6500, 6600, 1300, MVA1C, MVA2B, MVA3B, MAC125, MAC250, MAC500. Used on valve series: 200, 57, 58, 59.
1. VOLTAGE (100 Serie type coil) - XX Y 26* B69* 75 76* 84* 87* 88* 89* 90 91* 95 A1 A2 A3 ZZ VOLTAGE 120/60, 110/50 240/60, 220/50 100/60, 100/50 200/60, 200 /50 10/60 6/60 12/50, 12/60 24/60, 24/50 32/60, 32/50 48/60, 42/50 380/50, 440/50, 440/60, 480/60 220/60 127/50, 120/50 48/50 16/60 24/VDC (6 W) 24 VDC (4 W) 12 VDC (4 W) 12 VDC (6 W) 12 VDC (2.5 W) 24 VDC (2.5 W) 12 VDC (8.5 W) 24 VDC (8.5 W) 6 VDC (6 W) 32 VDC (7 W) 48 VDC (5.8 W) 64 VDC (7.5 W) 120 VDC (6.4 W) 220 VDC (8.7 W), 250 VDC (11.2 W) 90 VDC (8.8 W) 100 VDC (6.9 W) 125 VDC (10.9 W) 24 VDC (17.1 W) 12 VDC (17.4 W) 36 VDC (18.8 W) 28 VDC (8.2 W) 6 VDC (10.6 W) 190 VDC (6.5 W) 3 VDC (7 W) 38 VDC (6.4 W) 24 VDC (1 W) 12 VDC (1 W) 9 VDC (1 W) - XX Y 78* 86 93* ZZ
1. VOLTAGE (200 Serie type coil) VOLTAGE 120/60, 110/50, 24 VDC (6 W) 240/60, 220/50 100/60, 100/50 200/60, 200/50 6/60 12/60 24/60, 24/50 32/60, 32/50 48/60, 42/50 240/50 480/60, 440/50 127/60 415/50 220/60 380/50 550/60, 550/50 120/60, 110/50 600/60 127/50 48/VDC (6 W) 24 VDC (4.5 W) 24 VDC (2.5 W) 24 VDC (1.0 W) 12 VDC (6 W) 12 VDC (2.5 W) 48 VDC (2.5 W) 12 VDC (9.5 W) 24 VDC (8.5 W) 6 VDC (8.5 W) 32 VDC (10 W) 48 VDC (11.5 W) 64 VDC (10.5 W) 120 VDC (12.3 W) 250 VDC (9.2 W) 8 VDC (8.2 W) 24 VDC (12 W) 198 VDC (10 W) 72 VDC (11.3 W) 90 VDC (11.3 W) 100 VDC (9 W) 220 VDC (10 W), 230 VDC (11.6 W) 24 VDC (24 W) 55 VDC (10.6 W) 170 VDC (11.1 W) 15 VDC (8.1 W) 125 VDC (10 W) 36 VDC (11 W) 12 VDC (24 W) Consult Precautions page 364 before use, installation or service of MAC Valves
MOD. DD01 : Protection diode (DC) - MAX. 8.5W MOD. MOV1 : Protection varistor (AC) - MAX. 8.5W * Voltages are CLSF only
2. MANUAL OPERATOR (Common options for 100 & 200 Series type coils) - XX Y 4 ZZ MANUAL OPERATOR No operator Non-locking recessed Locking recessed Non-locking extended Locking extended 5* 6* 7* 8* 9* No Operator with Light Non-Locking Recessed with Light Locking Recessed with Light Non-Locking Extended with Light Locking Extended with Light

* Lights used with AA electrical connection 3. ELECTRICAL CONNECTION (100 Serie type coil) - XX Y ZZ AA BA CA CC FA GA HA JA* JB JC* JD JE JF JG JH JJ JM MA MB NA NC RA ELECTRICAL CONNECTION Wiring box with 1/2" NPS conduit Flying leads 1/2" NPS conduit 1/2" NPT conduit Military type 2 PIN Military type 3 PIN AA with ground wire Square connector Rectangular connector Square connector with light Rectangular connector with light Square connector on top (ISO2, ISO3) Rectangular connector on top (ISO1, ISO2, ISO3) JE with light JF with light Square connector, male only Rectangular connector, male only Electrical common conduit (100 Series-Manifold/900 Series) Electrical common conduit (100 Series-Stacking/700 Series) CA with ground wire CC with ground wire 3/8" NPS conduit - XX Y 3. ELECTRICAL CONNECTION (200 Serie type coil) ZZ AA BA CA CC EA EA FA GA HA JA* JC JJ NA NC ELECTRICAL CONNECTION Wiring box with 1/2" NPS conduit Flying leads 1/2" NPS conduit 1/2" NPT conduit Explosion proof (200 Series) Explosion proof (57, 58 & 59 Series) Military type 2 PIN Military type 3 PIN AA with ground wire Square connector Square connector with light Square connector, male only CA with ground wire CC with ground wire
* Not to be used with 100, 800 and 900 Series manifold mounting
4. COIL WIRE LENGTH (Common options for 100 & 200 Serie type coils) - XX Y ZZ (-VV) AA AB AD AE AF AG AR AU BA BB MOD L024 MOD L036 MOD L048 MOD L060 MOD L072 MOD L120 WIRE LENGTH 72 120
Series 6000 : wire length, from the base