English
Battery indicator and charging The symbol | in the display indicates when the batteries require charging. The indicator has three segments which disappear as the battery charge decreases, and will flash when the battery is running low. Charge the equipment as soon as possible when the indicator flashes! The battery indicator will show | when charging is complete (approximately 10 hours/ initially 24 hours). Fully-charged batteries will last for approximately 85 hours in standby or 3.5 hours operational time. These times apply at normal room temperature.

Please note!

Transfer code selection There are 38 transfer codes available which can be used to filter out unwanted signals. However, your conversation may still be overheard irrespective of which code is used. To enable communication between handsets (as well as monitor to handset), the same transfer code must be used on all units. In order to communicate with equipment that cannot select a code, enter code 0. 1. Press w repeatedly until the small digits in the top right hand corner of the display flash. 2. Scroll to the desired transfer code using v/V. 3. Press PTT to confirm. Scanning You can scan all available channels to locate any signals being transmitted. Once a signal has been located the display will show the channel number, and a signal will be heard for a few seconds. You can press PTT to stop at the located channel. Please note: while searching battery consumption will be significantly higher than normal. 1. Press w and { at the same time. The unit will start searching. 2. To stop scanning press w.
Termination (Roger) tone If selected a beep tone will be heard when you release the PTT button. This can be used as a reminder to the other person that you have finished talking and are waiting for a response. 1. Press w repeatedly until ro is displayed. 2. Scroll to the desired setting using v/V (OF =off, On=on). 3. Press PTT to confirm. Key tone If selected a tone will be heard when the handset buttons are pressed, this can be switched on or off. 1. Press w repeatedly until to is displayed. 2. Scroll to the desired setting using v/V (OF =off, On=on). 3. Press PTT to confirm. Searching two channels You can enter a different channel for simultaneous listening while using the selected operating channel. 1. Press w repeatedly until DCM is displayed. 2. Scroll to the desired setting using v/V (OF =off). Press w. 3. Scroll to the desired transfer code using v/V. Press PTT. 4. Press PTT to confirm. Key lock This function locks buttons w and v/V to prevent unintentional usage. 1. To activate the key lock press w until the display shows the key symbol. 2. To deactivate the key lock press and hold w until the key symbol disappears. Declaration of conformity Doro declares that the apparatus Doro AirLuba wt88 complies with the essential requirements and other relevant positions of Directive 1999/5/ EC, 2002/95/EC. A copy of the Declaration of Conformity can be found at www.doro.com/dofc Guarantee This product is guaranteed for a period of 12 months from the date of purchase. Proof of purchase is required for any service or support required during the guarantee period. This guarantee shall not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, not reasonably maintained or any other circumstances on the purchasers part. Furthermore, this guarantee shall not apply to a faults caused by the use of poor quality batteries, battery leakage, corrosion or similar events related to non DORO batteries. This guarantee does not in any way affect your statutory rights.
Never charge ordinary (non-rechargeable) batteries in the handset, since this will ruin the equipment. The guarantee does not cover this type of damage. The equipment must be charged initially for 24 hours before use during which time the handset cannot be used. The recharging system used in this model may result in it becoming warm. This is normal and will not damage the equipment. Important! Please note when programming all references to press = to press and then immediately release the button. Switching the Handset on/off Press and hold 1 for a few seconds to turn the handset on or off. To communicate 1. Make sure that all handsets (and monitor unit) are set to the same channel and transfer code. See below. 2. Press and hold PTT (Push To Talk) to speak. Please note! If you are unable to communicate it may be because different channels or transfer codes have been selected, the battery is running low or the units are too far apart. Channel selection All UHF/CB radio equipment share the available designated channels. If the chosen channel is in use select an alternate channel, the selected channel number will be displayed in standby mode. 1. Press w. The current selected channel flashes. 2. Select the desired channel using v/V. 3. Press PTT. Monitor function The monitor function can be used in weak signal areas to locate any other signal being transmitted. 1. Press w and V at the same time. 2. To stop monitoring press w.

1 Headset socket 2 Push to Talk (PTT) button 3 Call button
DOWN Menu button UP On/Off button

Voice control (VOX)

Area of use The handset is intended for both indoor and outdoor use, it is NOT resistant to rain, water, rough or other careless treatment. In ideal conditions ie: line of sight with no obstructions between handset/s and monitor, the range can be up to 6 km. Batteries 1. Remove the belt clip by lifting the small locating tab and pushing the clip upwards. 2. Before removing the battery cover release the locking clasp at the base of the handset. 3. Insert the rechargeable battery pack ensuring correct battery polarity is observed. 4. Refit the battery cover and belt clip. Charge the handset for 24 hours before use.
This handset can be used without having to press the PTT button to transmit. By setting the correct level, the handset can automatically determine when you are speaking. Test different settings until the sensitivity selected is acceptable. Please note that however accurate your setting there is always a small risk that increased noise from the surroundings may activate the transmitter, this may result in the initial word being unclear. The transmitter will shut off two seconds after you have finished speaking. VOX will be displayed while the function is active. If the handset transmits by itself the sensitivity is set too high and will need to be adjusted. Press w to be able to temporarily interrupt and change the setting. 1. Press w repeatedly until VOX is displayed. 2. Scroll to the desired setting using v/V (OF =off, 1=least sensitive.3=most sensitive). 3. Press PTT to confirm. Call melody You can select different call melodies (OF =off). 1. Press w repeatedly until CA is displayed. 2. Scroll to the desired melody (1 -5) using v/V. 3. Press PTT to confirm.
The rechargeable battery pack has been installed the handset must be charged for 24 hours before use. Charging Connect the mains adapter to the socket on the rear of the charging stand and to an electrical wall socket. Place the handset in the charger with the buttons facing out.

AirLuba wt88

6 km of range compact walkie talkie for outdoor conditions
8 channels and 38 sub-codes sure-grip design long standby and talk times

Colour: orange/black

Calling/talking
Voice activation (VOX) Headsets with Push-To-Talk button Dual channel monitor 2

Mechanical

Weight (g) 108

Technical

PMR 446 Mhz compatible Channels 3.5 2

Ringer

Roger beep Calling tones 5
Sub codes to each of the 8 selectable channels Range up to* (km) Stand by time (h)

Charging pod 1

Talk time (h) NiMh rechargeable battery pack AAA

Handset LCD Display

Backlit LCD display

Others

Auto power save
Compact, high performance walkie talkie that in spite of its small size offers 6 km of range. AirLuba is designed to handle the tough outdoor conditions of your favourite slopes, fishing spots and hiking trails.
May vary depending upon environmental and/or topographical conditions

www.doro.com