digital baby monitor

5 soothing lullabies 2-way communication excellent sound quality
Bm50 uses advanced digital technology to provide crystal clear sound that is both secure and free from interference with other networks.
Remote controlled night lights
Colour: applegreen / white General features Digital signal processing operation 120 duplex channels within the 1880MHz to 1900MHz band 32kbps ADPCM speech coding Full duplex TDD for interception and interference avoidance Voice encryption for maximum security Crystal clear voice quality Range (meters) Parent unit features Unit on/off 6 level digital volume control 5 level VOX control Voice level visual indication Baby sound high alert Dot matrix LCD LED LCD backlit Low battery indicator Link indicator Out of range warning Talk back to baby unit Baby unit nightlight remote on/off User replaceable rechargeable battery cells Battery level indication Use and charge on cradle

12 hours continuous use time, 20 hours use time on VOX Rechargeable on stand-alone charger Remote lullaby play control Room temperature monitoring with alerts Default function Belt-clip Baby unit features Unit on/off 5 level digital volume control Dot matrix LCD LED LCD backlit Link indicator Low battery warning Out of range warning Nightlight with on/off Backlit nightlight key Use with adaptor or alkaline batteries 20 hours use time 5 pre-recorded lullabies Lullaby playback with auto stop and lullaby selection Lullaby playback pause function Parent unit paging Room temperature detection Default function

Play, stop, pause

up to 50 m indoors (300 m outdoors)

4 AA (not included)

2 AA, NiMh

www.doro.com

Connection

Parent unit ( ) 1. Remove the battery cover by pressing in the latch on the underside and lifting. 2. Insert the two batteries as shown and replace the cover. 3. Place the parent unit in its stand and connect the mains adapter. The charging indication | flash charging indicator will light will in the display and the up on the charging stand.

Please note!

The equipment must be charged for 12 hours before use. It is normal for the device to become warm during charging and this is not dangerous. Low Battery will be shown in the display when the batteries are running low, and the unit will emit a beep once every minute. Place the parent unit in its charging stand. Fully-charged batteries will last for up to 12 hours. These times apply at normal room temperature. Because batteries only have a certain lifespan it is quite normal that operating time will decrease somewhat compared to the specifications when the baby monitor is used regularly. Only use rechargeable original batteries in the parent unit. The guarantee does not cover any damage caused by incorrect batteries. Baby Unit ( ) The baby unit can be connected to the mains power supply or can run on batteries. We recommend that the unit is operated on mains power, as battery operation time is limited and intended only for temporary use such as shorter trips away from home. If there are charged batteries in the unit they will be used in the event of a power cut. 1. Turn the button for the battery cover (use a coin) and slide the cover downwards. 2. Insert the batteries (not included) as shown, replace the cover and lock it with the button.
Low Battery will be shown in the display when the batteries are running low. New batteries will last for up to 25 hours.

Activation

1. Place the baby monitor close to the child (but out of reach) and connect the mains adapter. 2. Switch on the baby unit and the parent unit by pressing down 1. The green lights on the units will flash as they search to find each other. When contact has been established, they will shine with a steady light.

Setting the volume

1. Set the desired volume on the baby unit with +/-. This setting determines how loudly the lullabies and your voice speaking to the child will be heard. 2. Set the desired volume on the parent unit with +/-. In the Volume Off position, the noises from the child or its surroundings will not be heard there will be three warning signals in the parent unit if the noise from the child exceeds a certain level (e.g. when the child cries), see Sensitivity on the next page. To hear the child, the volume can now be turned up. Whatever the setting, the lights will provide a visual indication of the sound level from the child.

Speaking to the child

Hold the send button pressed down and speak into the loudspeaker.
Turning the nightlight on and off
Baby Unit Turn the nightlight on and off by pressing. Parent Unit 1. Press w. The display shows the suggested change e.g. Light On? to turn on the light. 2. Press O to turn on the nightlight; is shown in the display.

Lullaby

You can select the desired lullaby and start and stop playback. The lullaby will stop automatically after 5 minutes. Baby Unit 1. Press the button to select one (or all) of the five lullabies available. 2. Press to start or stop playback. Press and you will pause playback. Press again to resume playback. Start/stop lullaby from parent unit (Lullaby/Play) 1. Press w. 2. Scroll to Lullaby with +/-. Press O. 3. Play? will be shown. Press O to start playback. 4. Press O to start/pause or press w followed by O to stop. Select lullaby from the parent unit (Lullaby/Select New) 1. Press w. 2. Scroll to Lullaby with +/-. Press O. 3. Scroll to Select New. Press O. 4. Scroll to the desired lullaby or play all by pressing (Play All). Press O. 5. Playback will start.
English Here you can set the desired temperature range (Range). If the temperature in the childs room drops below the set minimum temperature Low will be shown, and if it rises above the set maximum temperature High will be shown. If the temperature falls below 7 C or exceeds 33 C -- will flash in the display. The display will always show the current temperature in the childs room. 1. w. Press 2. Scroll to Temperature with +/-. Press O. 3. Scroll to Range. Press O. 4. Select desired minimum temperature (10-19 C). Press O. 5. Select desired maximum temperature (22-30 C). Press O. 6. Press w to finish. Temperature Alarm (Alert) Here you can select whether or not a beep alarm should be heard when the temperature moves outside the set range above. 1. Press w. 2. Scroll to Temperature with +/-. Press O. 3. Scroll to Alert On/Off. Press O. 4. The display will show the suggested change e.g. Alert On? to activate the beep alarm. 5. Press O to accept the change. 6. Press w to finish. Here you can select if whether or not a beep alarm should be heard when the volume on the parent unit is switched off. In the Volume Off position, the noises from the child or its surroundings will not be heard there will be three warning signals in the parent unit if the noise from the child exceeds a certain level (e.g. when the child cries). 1. Press w. 2. Scroll to Sound Alert with +/-. Press O. 3. The display will show the suggested change e.g. Alert On? to activate the beep alarm. 4. Press O to accept the change or w to cancel without change. 5. Press w to finish. Here you can set the sensitivity of the microphone on the baby unit. 1. Press w. 2. Scroll to Sensitivity with +/-. Press O. 3. Select desired sensitivity with +/-. Press O. 4. Press w to finish. Level =least sensitive Level =most sensitive

Temperature

Sound Alert

Sensitivity

Paging
1. Press Page on the baby unit. If the parent unit is switched on and charged, it will emit a sound that will make it easier to locate. 2. Paging can be switched off by pressing Page or any button on the parent unit. The units range depends on whether or not the radio waves carrying the signals are restricted by obstacles in their path, and is usually between 50 and 300 metres. The indicator will flash when the units are out of range (the display will show Not Linked) and warning signals will be heard. The indicator will shine with a steady green light when the units are within range.
Doro hereby declares that this Doro bm50 product conforms to the essential requirements and other regulations contained in the directives 1999/5/EC (R&TTE), 2002/95/EC (ROHS). A copy of the manufacturers declaration can be found at www.doro.com/dofc.

Troubleshooting

The unit does not activate despite being switched on. - The batteries have run down (charge the parent unit). - Are the batteries inserted correctly? Acoustic Feedback - The units are too close to each other. No sound in handset (parent unit) - Turn up the volume. - Adjust the level for sound sensitivity. - Move the units closer together.
This device meets applicable international safety requirements for exposure to radio waves. This telephone measures 0.015 W/kg (per 10g tissue). The max. limit according to WHO is 2W/kg (per 10g tissue). The above figure is measured right next to the baby unit. At a typical application with around 1 meter from the baby the SAR value is significantly reduced (<0.00003 W/Kg).

Guarantee

This product is guaranteed for a period of 12 months from the date of purchase. If you experience any problems please contact the place of purchase. Proof of purchase is required for any service or support needed during the guarantee period. This guarantee shall not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, wrong batteries, non-maintenance or any other circumstances on the users part. Furthermore, this guarantee will not apply to any fault caused by a thunderstorm or any other voltage fluctuations. Batteries are consumables and are not included in any guarantee. This guarantee does not apply if batteries other than rechargeable original batteries have been used in the parent unit.