doro th80
1 Left menu button/Back/ Internal call 2 Speaker phone 3 Talk button
Front Housing - keypad area Lens -laser etching -pant (for numbers :colour white after laser) Shared phonebook 8 Recall button (PBX features) (for on/off keys: green and red respectively) 9 Right menu button/OK * and ring signal off/on Date : 8 May Scroll button # and keyguard Prepared by: Rickard N End call button and on / off Version :a

English

Connection. 1. Range.. 1. Battery.. 2. Base unit indicators. 2 The display. 2. Making a call.. 3 Receiving a call.. 3. Temporary silent mode. 3 Volume control.. 3 Turning On/Off.. 3 Redial. 3 Mute button.. 3 KeyGuard.. 3 Paging.. 3 Message button.. 3 Phonebook. 4. Incoming numbers/Caller ID.. 5 SMS messages.. 6 UK only.. 7. Message Indication (voice mail).. 8. Other info services.. 9. Sound. 10 Other settings. 10 Base settings. 11 Register a new handset. 11 Expanded system (+1).. 12 Troubleshooting.. 13 Specific Absorption Rate (SAR). 14. Declaration of conformity14 Guarantee. 14 UK. 14 Australia and New Zealand.. 15

Connection

1. Connect mains adapter and phone cable to respective wall sockets. 2. Insert battery according to the the markings. 3. Charge the handset with the keypad facing outwards (for 24 hours the first time). Language 4. Press Menu. 5. Scroll to HS settings using . Press OK. 6. Scroll to Language. Press OK. 7 Scroll to desired setting 8 / 9. Press OK. 8. Press L to return to standby mode. Date/Time 9. Press Menu. 10. croll to HS settings. Press OK. S 11.Scroll to Date/Time. Press OK. 12. croll to the required time format using 8 / 9. Press }. S 13. croll to the required date format using 8 / 9. Press }. S 14. nter time of day (HH:MM). Press }. E 15. nter date (DD MM YY). Press OK. E 16. ress L to return to standby mode. P
The telephones coverage will vary between 50 and 300 metres, depending on whether the radio waves carrying the conversation are blocked by obstacles in their path. Coverage can be improved by turning ones head so that the handset is aligned with the base unit. Sound quality declines as the limit is reached until the call is finally interrupted.

Battery

As batteries only have a certain lifespan it is quite normal that call time and standby time will decrease somewhat compared to the specifications when the telephone is used regularly. Fully-charged batteries (10 hours charging) will last for approx. 100 hours standby time or approx. 10 hours call time. These times apply at normal room temperature. Full battery capacity will not be reached until the batteries have been charged 4-5 times. The base unit has an automatic charging mechanism that prevents the batteries from being overcharged or damaged due to prolonged charging.

Please note!

Use only original battery (3.7V Li-ion polymer 465mAh) and original power adapter (7.5V DC 400 mA) Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instruction in your country. The base unit should not be located close to other electrical equipment, in direct sunlight or near any other strong heat source! This is to minimize the risk of any interference. It is normal for the device to become warm during charging and this is not dangerous.

Base unit indicators

Steady light while charging.

The display

Icon Function Shown when in range of base unit Key lock activated. Ring signal disconnected. Alarm activated. Speaker phone. During calls.
Icon Function ECO mode is enabled. Battery charge indicator. New SMS* received. New (missed calls) number received. Mute button.
Message waiting Message indication*.
* Only functions in certain countries. In order to save the batteries, the display is very dark on standby, press L once to illuminate. During calls, use.

Making a call

1. Enter the required number. 2. Press O , and the number will be dialled. Press L to end the call.

Receiving a call

1. Wait for the handset to ring. 2. Press O to answer. Press L to end the call.
To switch between handset/speaker press. Please remember that in speaker mode, it is only possible for one person at a time to talk. This product does not usually ring on the first signal to allow correct matching to the phone book. When the battery is low or when there is too great a distance to the base unit the telephone will be unable to connect to a line.

Temporary silent mode Volume control Turning On/Off
When someone calls, you can press Silence to turn off the handset ring signal. The volume can be adjusted during a call with }/{. Press and hold the L button for a few seconds to turn the handset off or on. Confirm disconnection by pressing Yes.

Redial

Press { and scroll through the 15 most recently dialled numbers using {/}. Press O.
Mute button KeyGuard Paging
The microphone can be switched on/off during a call using b. The KeyGuard is turned off/on by pressing and holding #. The handset will ring when J (on the base unit) is pressed. The signal will stop automatically after a while or if the L button on the handset or the J button on the base unit are pressed.

Message button

Can be used when there is a new message in e.g. Caller ID or SMS. Press the button to access the different messages.

Phonebook

200 telephone numbers (max. 24 digits) with names (max. 15 letters) can be stored in the handsets phonebook. If you subscribe to a caller ID service, the name allocated to the caller in the phonebook will be shown for incoming calls. You can also select different ring signals for different groups of numbers that are stored in the phonebook. Letters Each number key has been allocated certain letters. The phonebook is arranged according to the order of the buttons, which is not the same for all languages.

1.. [Space] #.. Switch 0

between upper/lower case letters ABC/abc/Abc (press & hold). Pause in telephone number
Save name/number in handset 1. Press 8 ( b ). Press Option. 2. Scroll to New entry. Press OK. 3. Press equivalent digit key one or more times for desired name. Press }. 4. Enter the telephone number, including the area code. 5. Press OK to save or first press } and scroll with 8 / 9 to assign the position to a ring signal group. Managing the phonebook 1. Press 8 ( b ). 2. Scroll among the entries with {/}. You can quick search the phonebook by pressing the corresponding number key for the first letter. 3. Press O to make a call or press Option for the following choices: - New entry see description above. - Edit entry - revise information. - View to see stored information. - Copy/Copy all to duplicate positions on other handsets. - Delete entry/Delete all - Capacity shows the number of free positions. - Edit call Gp. to select a certain ring signal for certain groups of numbers. - Speed dial to assign a position to a certain button in order to make it easier to make a call. To dial a speed dial number press down the equivalent 2 - 9 button. First scroll to the desired button, press OK, then scroll to the desired position in the phonebook. Press OK.
English Shared phone book The phone book in the base unit is shared by all handsets and has 10 entries which only need to be stored once however many handsets there are. Useful telephone numbers are pre-programmed in certain models. However these numbers may not match with caller identification for name/ringtone. 1. Press. 2. Scroll among the entries with {/}. 3. Press O to dial or scroll to the entry that is to be replaced. Press Option. 4. Scroll to Edit entry. Press OK. 5. Enter name. Press }. 6. Enter the telephone number, including the area code. Press OK.

Incoming numbers/Caller ID
The display shows you who is calling and the 30 most recent incoming numbers. Missed calls are indicated by in standby mode. If one and the same number calls in more than once it will be saved as only one entry.
This function requires a subscription from your service provider.
Retrieving and dialling 1. Press }. Scroll to the required entry using {/}. 2. Press O to make a call or press Option for misc. choices. Caller identification messages UnavailableNo information received, e.g. an international call. Withheld Number cannot be shown. Caller ID settings 1. Press }. Press Option. 2. Scroll to Settings. Press OK. 3 Scroll to required function, e.g. Category. Press OK. 4. Scroll to desired setting using 8 / 9. Press OK. Category New call alert Select whether the telephone will store missed or all incoming calls. You can activate a tone that is heard when new numbers have been received.

SMS messages

This applies only to subscribers of text messaging services (SMS). This service is not yet available in all countries. Maximum 160 signs per message. A new SMS message is indicated with the text New SMS and the symbol The memory can store up to 20 messages.
Program the correct number for your operator, see next page.
In most cases you must subscribe to the SMS service as well as the caller ID service supplied by your service provider for message reception to function. Information about the functions you can use varies depending on the service provider. It is not certain that all service providers can send/receive SMS with all types of equipment. With certain service providers you can send an SMS even to people without SMS equipment. In those cases the message is read by an automated voice. Failed SMS are saved in the outbox. There are also templates for frequently used texts.
Read new SMS/inbox 1. Press Menu. Scroll to SMS. Press OK. 2. Scroll to Inbox. Press OK. 3. Scroll to selected entry. Press Read. 4. Read your message. Press Option. 5. Scroll to the required selection. 6. Press OK and follow the instructions in the display. Write new SMS message 1. Press Menu. Scroll to SMS. Press OK. 2. Scroll to Write new SMS. Press OK. 3. Press corresponding digit key one or more times for the desired text.

1.. [Space]

between upper/lower case letters ABC/abc/Abc 4. Press Option. Scroll forward to send or store the message. Press OK. 5. Enter the telephone number including the area code, or press Option to retrieve the telephone number from the phonebook. 6. Press Send. 7. The display shows if the SMS has been sent successfully or not. If no error report is shown, the message has been sent successfully.

#.. Switch

English Entering the telephone number to SMS service centre/Send service Check that the correct number for your service provider has been programmed.

UK only

- - - - - 1. 2. 3. 4. 5. E.g. for BT: SMS-Centre 1 (sending): 147017094009 SMS-Centre 2 (receiving): 0800587529 To register for the SMS text messaging service you can either send a text message to another telephone number, or text REGISTER to 00000. Should you wish to reset your SMS settings text RESET to 00000. You can also request a delivery report by entering * 0 # prior to any SMS message. An SMS message can also be sent to a telephone number that does not support this feature, and will be received as a voice message. Not all networks (ie mobile, cable) are compatible. Press Menu. Scroll to SMS. Press OK. Scroll to SMS settings. Press OK. Scroll to Service centre. Press OK. Scroll to selected entry. Press OK. Enter number. Press OK.
Under Send service you specify which of the stored numbers is to be used for outgoing SMS. Message Alert You can activate a tone that is heard when new messages have been received. 1. Press Menu. Scroll to SMS. Press OK. 2. Scroll to SMS settings. Press OK. 3. Scroll to New SMS alert. Press OK. 4. Scroll to desired setting. Press OK.
Message Indication (voice mail)
This applies only to subscribers with access to a voice mail service. In addition, if you subscribe to services for message indication and caller ID the display will show if someone has left a message. A new message is then indicated with the text Message waiting on standby (only applies in certain countries).
The telephone number to call voice mail depends on the network and must be programmed see Network codes under Other services further on in this chapter.
Playback with hot key Hold 1 pressed down for a few seconds. Listen to the information/messages received. Playback via the menu 1. Press Menu. Scroll to Oper. Service. Press OK. 2. Scroll to Mailbox. Press OK. 3. Scroll to Call mailbox. Press OK. 4. Press Yes to dial. Listen to the information/messages received. Message Alert You can activate a tone that is heard when a new voice message is received. 1. Press Menu. Scroll to Oper. Service. Press OK. 2. Scroll to Mailbox. Press OK. 3. Scroll to Mailbox alert. Press OK. 4. Scroll to desired setting. Press OK.

Other info services

Most usual operator/extra services can be accessed via the menu or with the menu buttons during a call. Some functions are pre-programmed but is not certain that all functions will work on delivery as this will depend on the country of installation/operator. You can change the codes that are sent, see below in this chapter. The functions available will depend on your service provider.
You may have to pay extra for some services, contact your service provider for more information. Some services will not work unless you have contacted your service provider to activate them.

Busy number/call waiting 1. Connect an external call and wait until the timer is shown. Press Option. 2. Scroll to required service. - CW accept Answer incoming call waiting (= R 2). - CW reject Refuse incoming call waiting and send engaged tone (=R 0). - Auto callback When a number is engaged. When the number is free you will hear a quick ring signal (=5). 3. Press OK. Under inquiry/alternating/answered call waiting Use the respective menu button: - Brok Switching between two calls (= R 2). - Conf Conference/three party call (= R 3). Call Forwarding 1. Press Menu. Scroll to Oper. Service. Press OK. 2. Scroll to Call forward. Press OK. 3. Scroll to required service. Press OK. 4. Follow the instructions given in the receiver, speaker or the display. Other services 1. Press Menu. Scroll to Oper. Service. Press OK. 2. Scroll to Functions. Press OK. 3. Scroll to required service. - Call anonymous Withhold your number from recipient. The code for this service must be programmed manually, see below. - CW on/off Command to turn the call waiting service off or on easily. - Network codes The codes supplied when you use the operator services can be changed. The number for Message indication can also be programmed here. 4. Press OK. Follow the instructions given in the receiver, speaker or the display.
1. Press Menu. Scroll to Sound. Press OK. 2. Scroll to desired function, e.g. Ringer. Press OK. 3. Scroll to desired function, e.g. Ring volume. 4. Scroll to desired setting 8 / 9. Press OK. Ringer The handsets ring signal can be adjusted. Tones Can be heard when pressing buttons/when charging starts, low battery, confirmation or when out of range.

Other settings

1. 2. 3. 4. Press Menu. Scroll to HS settings. Press OK. Scroll to required function e.g. Language. Press OK. Scroll to desired setting. Press OK.
This function allows you to dial a predetermined number by pressing any button (however not Opt which allows you to disconnect this function). Alarm The activated alarm is indicated with on standby. When the alarm goes off, an audio signal is heard for 30 seconds. Use Stop to switch it off permanently. The volume is determined by the set ringer level. Date/Time Setting of date/time is described in the Connection chapter. Select base Only used in systems with more than one base unit. Display Setting the contrast and the text displayed in standby mode. Language Language settings are explained in the Connection chapter. Auto answer The handset answers incoming calls when it is lifted from the base unit. Register To register a new handset, see separate description. De-Register To deregister a handset from a base unit. System PIN is 0000 on delivery. Handset reset Resetting the handset. Direct call

Base settings

Base PIN is 0000 on delivery. 1. Press Menu. 2. Scroll to Base settings. Press OK. 3. Scroll to desired function e.g. Exchange code. Press OK. 4. Scroll to desired setting. Press OK. The base units ring signals can be set at several different levels. You can decide whether all handsets should ring at once when there is an incoming call, or if one handset should start ringing before the others. You can set the number of ring signals for this function as well. Dial mode Must be in tone in most countries. Flash time Only for adaptation to international company switchboards. For most countries, the setting is 100 ms. Msg Wait Off To turn off the message indication manually. System PIN You can change the PIN code (0000 on delivery). Exchange codeEnter the digit that obtains an external line and the telephone will insert a pause automatically when a number starts with that digit. ECO mode When this function is enabled, less power is consumed during charging, if you use one handset only. System reset Reset base unit. Ringer HS priority

Register a new handset

All new handsets that are to use the base unit must be registered. See also the Expanded Systems chapter for more information. 1. Press Menu. 2. Scroll to HS Settings. Press OK. 3. Scroll to Register. Press OK. 4. Scroll to the desired base. Press OK. 5. Enter the base units PIN code (0000 on delivery). Press OK. 6. Hold down the base units search button J until a beep is heard. 7. If the registration is successful the handset will return to standby mode within one minute.

Expanded system (+1)

All handsets included in the package are already registered to the base unit. The handset number used for internal calls is shown in the display on standby mode. The base unit should be positioned centrally so that the coverage area is roughly equal for all handsets. You can register up to 5 handsets to one base unit.
This model is GAP (Generic Access Profile) compatible, which means that the handset and the base unit can both be used with most other GAP compatible units irrespective of manufacturer. However the GAP protocol cannot guarantee that all functions may be accessed.
Intercom / internal call 1. Press Int. 2. Scroll to selected handset. Press OK. A tone will be heard if an external call comes in while an internal call is in progress. End the internal call with L and then answer the external call with O. Transferring calls/Conference between handsets 1. An external call is connected. 2. Initiate an internal call as described above. 3. Press L to transfer the call or press Conf for conference.

Troubleshooting

Check that the telephone cord is undamaged and properly plugged in. Disconnect any additional equipment, extension cords and other phones. If the problem is resolved, the fault is with some other equipment. Test the equipment on a known working line (e.g. at a neighbours house). If the equipment works there the fault is probably with your telephone line. Please report this to your network operator. No number shown when ringing - This function requires a Caller ID subscription from your service provider. - A switchboard cannot usually pass on incoming numbers. Warning signal during call/Cannot connect - The batteries may be running low (recharge the hand unit). - The hand unit may be nearly out of range. Move closer to a base unit. - Try turning the ECO Mode function off under System settings. Telephone does not work - Check that the adapter and telephone cord are connected to the base unit and to their respective wall sockets. - Check that you have selected Tone Dial, see System Settings/Dial. - Check the charge status of the handset batteries. - Try connecting another telephone, known to be in working order, to the line socket. If that phone works then it is likely that this equipment is faulty. The telephone continues to ring - Some of the telephones ringers do not follow the line signal, which means that the signal may continue for up to 10 seconds after answering a call. SMS does not work - In order for this feature to function, you must subscribe to the SMS service from your network provider. - Check that the correct telephone number is stored for each service. If the telephone still does not work, contact the place of purchase for service. Dont forget the receipt or a copy of the invoice.
Specific Absorption Rate (SAR)
This device meets applicable international safety requirements for exposure to radio waves. This telephone measures 0.06 W/kg (measured over 10g tissue). The max. limit according to WHO is 2W/kg (measured over 10g tissue).

Eco functionality

We have introduced the ECO FUNCTIONALITY label to help customers identify products within our assortment having a lower impact on the enviornment. Products carrying this label feature: - Reduced power consumption in both operational and standby modes. - Adaptive transmission power depending on range on base unit. - Full Energy Star compliance and approval (www.energystar.gov)

Doro AB, an ENERGY STAR Partner
Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the US EPA and the EU Commission. ENERGY STAR and the ENERGY STAR mark are registered US marks. ENERGY STAR is a registered mark owned by the US government.
Declaration of conformity
Doro hereby declares that the Doro th80 products conform to the essential requirements and other regulations contained in the directives 1999/5/EC (R&TTE), 2002/95/EC (ROHS). A copy of the manufacturers declaration is available at www.doro.com/dofc

Guarantee

This product is guaranteed for a period of 12 months from the date of purchase. If you experience any problems please contact the place of purchase. Proof of purchase is required for any service or support needed during the guarantee period. This guarantee will not apply to a fault caused by an accident or a similar incident or damage, liquid ingress, negligence, abnormal usage, non-maintenance or any other circumstances on the users part. Furthermore, this guarantee will not apply to any fault caused by a thunderstorm or any other voltage fluctuations. As a matter of precaution, we recommend disconnecting the device during a thunderstorm. Batteries are consumables and are not included in any guarantee. This guarantee does not apply if other batteries than DORO original batteries have been used.
If you cannot resolve the fault using the faultfinder section, technical support is available by email on tech@doro-uk.com or via a premium rate telephone number: 0854, calls cost 50 pence per minute (prices correct at the time of publication). Further contact details are available on our website: www.doro-uk.com Alternatively you can write to: Customer Services Doro UK Ltd 1 High Street Chalfont St Peter Buckinghamshire SL9 9QE 14
Australia and New Zealand
Products permitted for connection to the telephone network are marked with in Australia and in New Zealand. These marks indicate the products comply with the regulations and can be legally connected in the country of purchase. Customer support AUSTRALIA DORO Australia Pty Ltd PO Box 6646 Silverwater BC NSW 1811 Australia Ph: Ph: 023 Fax: (02) 9748-6892 support@doro.com.au www.doro.com.au NEW ZEALAND Atlas Gentech (NZ) Limited Private Bag 14927 Panmure Auckland New Zealand Ph: 0900-500-25 (Toll Call) Fax: (09) 574-2722 support@atlasgentech.co.nz
Electro Magnetic Radiation (EMR) This telephone complies with applicable safety requirements for exposure to radio waves. The mean power of this telephone is not greater than 14 mW. This is below the 20mW limit at which testing is required. REN (RN for New Zealand) The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to connect more than 1 telephone to your telephone line. A standard telephone line has a maximum REN capacity of 3 (RN of 5). It is possible to connect 3 devices with a REN of 1 (RN of 1) with no degradation to the products performance. Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring at all. ALL PRODUCTS The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with the minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecoms network services. This equipment shall not be set to make automatic calls to the Telecom 111 Emergency Service. This equipment may not provide for the effective hand-over of a call to another device connected to the same line. This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom Customers. CND PRODUCTS If a charge for local calls is unacceptable, the DIAL button should NOT be used for local calls. Only the 7 digits of the local number should be dialled from your telephone. DO NOT dial the area code digit or the 0 prefix. 15