Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose) and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Digital Security Controls Ltd. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada. WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

Out of Warranty Repairs

Digital Security Controls Ltd. will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to Digital Security Controls Ltd. must first obtain an authorization number. Digital Security Controls Ltd. will not accept any shipment whatsoever for which prior authorization has not been obtained. Products which Digital Security Controls Ltd. determines to be repairable will be repaired and returned. A set fee which Digital Security Controls Ltd. has predetermined and which may be revised from time to time, will be charged for each unit repaired. Products which Digital Security Controls Ltd. determines not to be repairable will be replaced by the nearest equivalent product available at that time. The current market price of the replacement product will be charged for each replacement unit.

New Features

PC5200 Support
The PC5020 v3.1 and higher supports the new PC5200 Power Supply module. See PC5200 Power Supply Output Module, Pg 2. The PC5020 v3.1 and higher supports the PC5936 15-station audio matrix module. See PC5936 Audio Interface Module, Pg 3. SIA False Alarm Reduction has been incorporated in this version. See the Quick Reference Chart SIA-FAR on the following page. This feature enables the system (or partition) to arm if there is no zone activity for a programmed time period. See sections [191]-[198] - No-Activity Timer (Partition 1-8), Pg 30. The Auto- arm Pre-alert Time is now programmable. The default value for this timer has been extended to 5 minutes. See Section [199] - Auto-arming Pre-Alert Time, Pg 30.

Connect the PC5020 and modules that use the telephone line(s) in the following order:

PC5936

For example, if you are installing a PC5020 with a LINKS1000/GSM1000 and a PC5936 intercom module, connect the incoming line to the LINKS1000, then from the LINKS1000 to the PC5020, then from the PC5020 to the PC5936 audio module and then from the PC5936 module to the house telephones. NOTE: Ensure that all plugs and jacks meet the dimension, tolerance and metallic plating requirements of 47 C.F.R. Part 68, SubPart F. For proper operation there must be no other telephone equipment connected between the control panel and the telephone company facilities. NOTE: Do not connect the alarm panel communicator to telephone lines intended for use with a FAX machine. These lines may incorporate a voice filter which disconnects the line if anything other than FAX signals are detected, resulting in incomplete transmissions.
2.5 Current Ratings - Modules & Accessories
In order for the PC5020 system to operate properly, the power output capabilities of the main control and expansion devices must not be exceeded. Use the data presented below to ensure that no part of the system is overloaded and cannot function properly. PC5020 Device Ratings (@ 12 VDC) LCD5500Z Keypad: 85 mA LCD5501Z Keypad: 45mA
2.3 Wire Routing for Power & Non-Power Limited
All wiring entry points are designated by the arrows. All circuits are classified UL installation power limited except for the battery leads which are not power limited.
Installation and Wiring: 2.6 Assigning Zones to Zone Expanders
LCD5501Z32-433 Keypad/Receiver: 260mA (max.) PC5100 Addressable Device Interface Module: 40mA PC5508Z Keypad: 80 mA PC5516Z Keypad: 90 mA PC5532Z Keypad: 120 mA PC5108 Zone Module: 35 mA PC5108L Downlook Interface: 60 mA PC5132 Wireless Module: 125 mA PC5200 Output Module: 20 mA PC5204 Output Module: 20 mA PC5208 Output Module: 50 mA PC5320 Multiple Receiver Interface Module: 55mA Escort5580(TC) Module: 150 mA PC5400 Printer Module: 65 mA PC5700 Fire Module: 150 mA PC5904 Central Station Talk/Listen Module: 175mA PC5936 Audio Interface Module: 65 mA PC5937 Audio Port Expansion Module: 5mA PC5921 Intercom Audio Station: 20 mA PC5921 EXT Door Box Audio Station: 20 mA PC5921 EXT/R Door Box Audio Station: 35 mA DLM-4L v1.0: 180 mA T-Link module: 150mA System Outputs (all 12 VDC)
PC5020 VAUX: 550 mA. Subtract the listed rating for each keypad, expansion module and accessory connected to VAUX or Keybus. NOTE: The maximum AUX capacity for 24-hr standby is 420mA. 700 mA. Continuous Rating. 3.0 A. Short Term. Available only with standby battery connected. 1.0 A. Continuous Rating. Subtract for each device connected. 3.0 A. Short Term. Available only with standby battery connected. 1.0 A. Continuous Rating. Subtract for each device connected. 3.0 A. Short Term. Available only with standby battery connected. 250 mA. Subtract for each device connected. Subtract the total load on this terminal from the PC5020 VAUX/Keybus output. 100 mA. Subtract for each device connected. Subtract the total load on this terminal from the PC5020 VAUX/Keybus output.

Installer Code. Section [006]
3.4 Programming Toggle Options
Some Sections contain several toggle options. The panel will use zone lights 1 through 8 to indicate if the different options are enabled or disabled. Refer to the Programming Worksheets to determine what each option represents and whether the light should be ON or OFF for your application. Press the number corresponding to the option to toggle the light ON or OFF. Once all the toggle options have been selected correctly press the [#] key to exit the Section and save the changes. The panel will turn off the Ready light and turn on the Armed light.
3.2 Programming Decimal Data
When the Ready light is ON the panel is waiting for the information to be programmed for the selected Section. Enter the information written in the boxes for the Section found in the Programming Worksheets. If a digit is entered for each program box in a Section the panel will automatically exit from the Section. It will turn OFF the Ready light and turn the Armed light back ON. You can also press the [#] key to exit a Section before entering data for every box. This is handy if you only need to change the first few program boxes. All other locations in the Section will remain unchanged. If the [#] key is pressed the panel will turn OFF the Ready light, turn ON the Armed light and exit you from the Section.
3.3 Programming Hexadecimal Data
On occasion, hexadecimal (Hex) digits may be required. To program a Hex digit press the [*] key. The panel will enter Hex programming and Ready light will begin to flash.

3.5 Viewing Programming

LED and LCD5501Z Keypads Any programming section can be viewed from an LED or LCD5501Z keypad. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section. The keypad displays the information using a binary format, according to the following chart:
See Hex data entry instructions
Press any of the Emergency keys (Fire, Auxiliary or Panic) to advance to the next digit. When all the digits in a section have been viewed, the panel will exit the section: the Ready light will turn OFF, and the Armed light will turn ON, waiting for the next three-digit programming section number to be entered. Press the [#] key to exit the section LCD Keypad When a programming section is entered, the keypad will immediately display all the information programmed in that section. Use the arrow keys (< >) to scroll through the data being displayed. To exit the section, scroll past the end of the data displayed, or press the [#] key.

Section 4: Keypad Commands
Use any system keypad to enter commands, or to program the PC5020 security system. The LED keypad uses function and zone indicator lights to represent alarm functions and status. The LCD keypad provides a written description on the liquid crystal display and uses function indicator lights to communicate alarm status to the user. The PC5020 Users Guide provides basic directions for arming and disarming the system, bypassing zones and performing user functions from the keypads. The following sections provide additional details on these functions.

4.1 Arming and Disarming

Arming The system cannot be armed unless the Ready light is on. If the Ready light is not on, ensure all protected doors and windows are secure and stop movement in areas covered by motion detectors. When the Ready light is on, enter a valid access code. As each digit is pressed the keypad will beep. If an incorrect code is entered, the keypad will emit a steady 2-second beep to indicate that the code was not correct. If the code is correct but the Ready light was not on, the panel will beep six times rapidly followed by a long 2-second beep to indicate the system was not ready. When the correct code is entered and the system is ready, the panel beeps six times rapidly, and the Armed light turns on. The panel begins counting down the Exit Delay. If the Audible Exit Delay option is enabled, the keypad will beep every second until the Exit Delay expires. The keypad will beep rapidly for the last 10 seconds of Exit Delay to warn the user the system is about to arm. Exit the premises through the designated entry/exit door before the Exit Delay expires. Users can restart the Exit Delay while it is counting down by pressing the Away key. The system will not log the user who re-started the Exit Delay, unless the Quick Arming Disabled/Function Keys Require Code option is turned on (Section [015], option [4]). Other methods of arming are available (see Section [*] [0] Quick Arm, [*][9] Arming without Entry Delay, and section 4.4 Function Keys). NOTE: The PC5020 has a built-in feature called Audible Exit Fault (see Section 5.3 Basic Programming PWS Sect 3 [001]-[004] for more information). Stay and Away Arming When a user arms the system, if any zones on the system have been programmed as Stay/Away, the panel will immediately turn on the Bypass light. The panel will then monitor all zones programmed as Delay 1 and Delay 2. If no delay type zone is violated by the end of the Exit Delay (i.e., nobody leaves through the entry/exit door), the panel will bypass all Stay/Away type zones. The panel is now Stay armed. The Bypass light will remain on to inform the home owner that the interior protection is bypassed. This is a convenience for users that want to arm the panel while at home. Using this method, users do not have to bypass the interior zones manually. Users can add the Stay/Away zones back into the system at any time by entering [*] [1] (see section [*][1] Zone Bypassing), or by using the Away function button. If a delay zone is violated during the Exit Delay (i.e., somebody leaves through the designated entry/exit door), all zones will be active after the Exit Delay expires. The panel is now Away armed. The Bypass light on the keypad will be off. Other methods of Stay and Away arming are available (see section Function Keys).

If the Code Required for Bypass option is enabled, the Master code or Supervisor codes must be used to access this feature. NOTE: If a 24-hr zone is bypassed, ensure that the zone is restored or disabled before removing the bypass.
Code required for bypass. Section [015], Option [5]

4.2 [*] Commands

[*][1] Zone Bypassing Users can bypass individual zones using the [*][1] keypad command. This command can be used if users want to have access to an area while the partition is armed, or to bypass a defective zone (bad contact, damaged wiring) until service can be provided. A bypassed zone will not cause an alarm. Instructions on zone bypassing can be found in the PC5020 Users Guide (Zone Bypassing). When the partition is disarmed, all zones bypassed using [*] [1] will be unbypassed, except for 24-Hr zones. If the Code Required for Bypass option is enabled, an access code will be required to enter the Bypass mode. Only access codes with the Bypass attribute enabled will be able to bypass zones (see section [*] [5] Programming Access Codes). These features are also available on the [*][1] zone bypassing menu: Bypass Recall: Press [99] while in the [*][1] menu to recall the last set of bypassed zones. Clear Bypasses: Press [00] while in the [*][1] menu to clear all bypassed zones. Bypass Groups: Users can program a group of zones to be bypassed (bypass group). Each partition can have a different bypass group. To program a bypass group, in the [*][1] menu, select the zones to be bypassed. Press [95] to save the group. To recall the group, press [*][1] followed by [91].
[*][2] Trouble Display The panel constantly monitors itself for several different trouble conditions. If a trouble condition is present, the Trouble light will be ON and the keypad will beep twice every 10 seconds. The trouble beep can be silenced by pressing any key on any keypad. If Bell Squawk on Trouble is enabled (section [014], option[5]), the bell will squawk every 10 seconds when a Trouble condition is present. NOTE: If there is an AC Trouble, the keypad will not beep for a General System Trouble. To view Trouble conditions from an LED or LCD5501Z keypad: 1. Press [*] [2]. 2. The keypad will flash the Trouble light. The zone indicator lights corresponding to the present Trouble conditions will be ON. When using an LCD keypad, the Trouble conditions will be listed on the display. Users can scroll through the list of present Trouble conditions using the arrow (< >) keys. NOTE: Troubles can be viewed while armed using the LCD keypad, provided the keypad is version 2.0 or later. Older keypads will incorrectly display Fire Trouble. If using older LCD keypads, program section [013], option [3] as OFF to ensure that Troubles are displayed correctly. The various Troubles are described below:

NOTE: If you enable the Bell Squawk on Arming/Disarming option (section [014], option [1]), the bell will sound arm/disarm bell squawks for all access codes, regardless of the programming for attribute [7] (See Section 5.3 Basic Programming PWS Sect 3 [001]-[004] and Section 5.4 Advanced Programming). Installer Programming - Codes and Options There are three codes which can be programmed by the installer in Installer Programming: the Master Code, the Installer Code, and a Maintenance Code. All other access codes can be programmed through the [*][5] command, as described previously in this section. The master code can also be programmed by the user as access code (40). However, if the Master Code Not Changeable option is enabled, the Master Code can only be changed in Installer programming. The Maintenance Code can only be used to arm and disarm the system. The Maintenance Code cannot bypass zones, use [*][9] to arm the system, cancel auto-arming, or perform [*][7] command functions. There will be no arm/ disarm bell squawks when the Maintenance Code is used. General access codes can arm and disarm the system. When the Code Required for Bypassing option is enabled, users will need to enter a valid access code in order to bypass zones. Individual access codes can have the Zone Bypassing attribute disabled under Access Code Attribute programming, as described previously in this section.
Installer Code. Section [006] Master Code. Section [007] Maintenance Code. Section [008] Master Code Not Changeable. Section [015]: [6] Code Required for Bypassing. Section [015]: [5]
NOTE: Only one partition at a time can use [*][5] programming. [*] [6] User Functions NOTE: Only one partition at a time can use [*][6] programming. To program user functions, perform the following: 1. Press [*] [6] [Master Code]. The keypad will flash the Program light. 2. Press the number [1] to [5] for the item to be programmed. [1] - Time and Date See the PC5020 Users Guide for instructions on setting the time and date (Setting the Time and Date). [2] - Auto-arm Enable/Disable Enter [2] to enable (three keypad beeps) or disable (one long beep) the auto-arm feature. [3] - Auto-arm Schedule Enter [3] to change the auto-arm time for each day of the week. Scroll to the day of the week you want to change, or enter the number of the day (1-7 for Sunday to Saturday). On an LED keypad, zone lights 1-7 will represent Sunday to Saturday. When you have selected a day, enter the auto-arm time in 24-hr format (i.e., enter a 4-digit number in [hhmm] format). The system will return you to the day selection menu. Scroll to the next day you want to program, or to exit auto-arm programming, press [#]. NOTE: To change the Auto-arm schedule at another partition, users with access to that partition will have to select the partition on the keypad, before entering the

Delay 2 Instant Interior

Interior Stay/Away.

Delay Stay/Away

Delayed 24-hr Fire (Hardwired)
Standard 24-hr Fire (Hardwired) 24-hr Supervisory
24-hr Supervisory Buzzer 24-hr Burglary 24-hr Holdup 24-hr Gas 24-hr Heat 24-hr Medical 24-hr Panic 24-hr Emergency 24-hr Sprinkler 24-hr Water 24-hr Freeze 24-hr Latching Tamper
Momentary Keyswitch Arm Maintained Keyswitch Arm LINKS Answer
Programming Sections: 5.3 Basic Programming PWS Sect 3
[001]-[004] ZONE DEFINITIONS

Interior Delay Zone

The Interior Delay Zone is normally used with motion detectors and has a standard Exit Delay time. If the panel is armed, and a Delay zone is violated during the Exit Delay (or the Away function key is used), the Interior Delay Zone will be active at the end of the Exit Delay. This zone will cause an instant alarm when violated. This zone type will follow the Entry Delay time provided that a Delay zone is violated first. If the panel is armed, and a Delay zone is NOT violated during the Exit Delay (or the Stay function key is used, or [*][9] armed), a violation of this zone type will initiate Entry Delay 1. These zones are active at all times but do not cause an alarm, and do not show up in alarm memory. Zone Attributes such as Zone Bypassing and Door Chime affect the functionality of this zone. A 24-hr Non-alarm zone may be used for Zone Follower automation applications. NOTE: This zone type will be active in Walk Test. Tampers and Faults. Zones programmed as 24-hr Nonalarm type will not cause alarms. NOTE: Alarms on this zone will not initiate Downlook. These zones will follow the waterflow Delay Timer. When a delayed waterflow zone is violated, the waterflow timer will start, (any subsequent delayed waterflow zones that become active do not reset or abort this timer). If there are still delayed waterflow zones open when the waterflow timer expires, the panel will go into alarm and communicate the event(s) regardless of the armed state. A waterflow alarm is a Fire alarm. The Fire related bells and Aux functions are activated. This Zone type functions similar to Type 27 (Delayed 24-hr waterflow), but does not follow the Waterflow Delay Timer. When this zone is violated, it will immediately go into alarm. This zone type always uses a single EOL configuration. This zone ensures that an alarm condition persists by resetting a tripped sensor in a fire zone and confirming that the sensor has remained tripped or is waiting for the sensor to re-trip within a set period of time (e.g., cycling power to a smoke detector to ensure the condition persists when power is restored). The alarm sequence for the zone is indicated below: Step #1 Duration 20 Seconds Sensor Reset Step #2 Duration 10 Seconds Settle Time (Power-up) Step #3 Duration 60 Seconds Check for Verified Alarm NOTE: If another Fire device detects Fire during the Auto Verify or Delay sequence, the sequence is terminated and alarms are immediately generated for all pending zones. This applies to all other Fire zones on the system regardless of the partition assignments (i.e., two fire alarms anywhere on the system will cancel all pending fire delays and create immediate alarms). When this zone is violated, the system turns on the keypad buzzer, and communicates the supervisory alarm condition to the monitoring station. The buzzer will not follow the Bell Time-out. To silence the buzzer, a valid access code must be entered. NOTE: The fire supervisory alarm is not affected by the waterflow silence inhibit option described in [018], Option 4, Pg 32 A zone programmed as this type has different characteristics in the armed and disarmed state. In the disarmed state, violating this zone will sound the keypad buzzer but will not log or report the event. In the armed state, violating this zone will sound the bell and communicate the event. Used only with wireless smoke detectors. Functions same as Zone Type [07]. Used only with wireless smoke detectors. Functions same as Zone Type [08].

OFF 3 Verbal Alarm ON

OFF 4 Waterflow Silence Inhibit ON OFF 5 Keypad Buzzer Alarm ON OFF 6 Cross Zoning / Police Zone Select ON

Exit Delay Restart

AC Trouble Beeps
Programming Sections: 5.4 Advanced Programming PWS Sect 4
[020] - Keypad Zone Assignment Assigning Keypad Zones Each keypad has a zone input to which a device (e.g., a door contact) can be connected (see section 2.11 Keypad Zones for wiring information.) Once the keypad zones are installed, enter the 2-digit zone designated for each keypad (slot), from 01-64. NOTE: 24-hr Supervisory (LINKS) and LINKS Answer Zones cannot be used on keypad zones. Fire zones can not be used on keypad zones if DEOL is enabled.
[030] - Fast Loop Response An eight bit toggle option controls which main board zones have Fast Loop (36 ms) or Normal Loop Response (540 ms). Fast Loop Response is typically used for vibration sensors.
5.4 Advanced Programming PWS Sect 4
[101]-[164] Zone Attributes The two sets of attributes (1-8 and 9-16) can be toggled by pressing 9 within any zones attribute section. If the Ready LED is on, the keypad is indicating Zone Attributes 1-8; if the Ready and Armed LEDs are on, the keypad is indicating Zone Attributes 9-16. The following options can be enabled or disabled by zone. NOTE: DO NOT change Fire zones attributes from the default settings. [101]-[164] ZONE ATTRIBUTES

Attribute

Bell Bell Type Chime
ON OFF ON OFF ON OFF Silent Alarm
An alarm will cause the bell output to activate. The bell output will be steady when the zone is in alarm. The bell output will pulse when the zone is in alarm. Every keypad will chime when the zone is violated and when the zone is secured. Door Chime will work in both the armed and disarmed states. The zone will not chime the keypads. The zone can be manually bypassed. The zone cannot be bypassed. The system (partition) can be armed with the zone violated. The zone will be temporarily bypassed, and when the zone is secured it will be added back into the system. The system cannot be armed if this zone is open. The zone will shut down after a programmed number of alarms, inhibiting further transmissions to the monitoring station. The bell can follow swinger shutdown if programmed. Swinger Shutdown Disabled The reporting of zone alarms will be delayed for the programmed time. If a valid access code is entered within this time, no alarm signal will be communicated. When an alarm occurs, the reporting code is transmitted immediately. NOTE: Transmission Delay cannot be used on fire zones. Zone is Wireless. The zone will ignore the main board zone (if applicable) and respond to the corresponding zone enrolled on the PC5132. Zone is Hardwired. The zone uses the corresponding hardwired zone. Zone is a Cross Zone. Zone is enabled for Cross Zoning. Zone is not a Cross Zone. Zone is not enabled for Cross Zoning. The default state for the Cross Zone attribute is OFF for all zone types. NOTE: DO NOT change Fire Zones attributes from the default settings.

LINKS Dialing

Delinquency
[381] - SECOND COMMUNICATOR OPTION CODES
Option 1 Communicator Code Opening After Alarm Keypad Ringback On/Off ON Description Opening After Alarm Keypad Ringback Enabled. When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the keypad will sound a series of 8 beeps to confirm to the end user that the Opening After Alarm code was sent and received. This ringback will occur for each Opening After Alarm code successfully reported. Opening After Alarm Keypad Ringback Disabled Opening After Alarm Bell Ringback Enabled. When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the bell will sound a series of 8 squawks to confirm to the end user that the Opening After Alarm code was sent and received. This ringback will occur for each Opening After Alarm code successfully transmitted. Opening After Alarm Bell Ringback Disabled SIA Sends Programmed Reporting Codes. This option is for use with the SIA communication format.). If 00 is programmed in the reporting code section, the event will not be communicated. When this option is ON and there is a valid reporting code programmed in the reporting code section, the programmed reporting code will be transmitted. If FF is programmed as a reporting code, the event will not be communicated. Reporting Code Entry Option ON Option OFF 00 No Transmission No Transmission FF No Transmission Auto Reporting Code sent 01-FE 01-FE sent Auto Reporting Code sent SIA Sends Automatic Reporting Codes. When this option is OFF and there is a valid reporting code (01-FE) or FF programmed in the reporting code section, the panel will transmit an automatic reporting code for SIA only. This would be used when automatic reporting codes are required but there is a requirement for a different reporting code (e.g., Pager format, etc.). Closing Confirmation Enabled. When a Closing reporting code is successfully transmitted to a programmed telephone number, the keypad will sound a series of 8 beeps to confirm to the end user that the Closing code was sent and received. Closing Confirmation Disabled. There will be no keypad ringback when a Closing reporting code is successfully transmitted to a programmed telephone number. Talk/Listen (PC5936) on Phone #1/3 Enabled. If Talk/Listen is requested for an event by the PC5936, the panel will request the session on the next communication on phone number 1/3 (via L-Block) to the central station. Talk/Listen (PC5936) on Phone #1/3 Disabled. The panel will not request a Talk/Listen session for an event even if the PC5936 has requested it. Talk/Listen (PC5936) on Phone #2 Enabled. If Talk/Listen is requested for an event by the PC5936, the panel will request the session on the next communication on phone number 2 (via L-Block) to the central station. Talk/Listen (PC5936) on Phone #2 Disabled. The panel will not request a Talk/Listen session for an event even if the PC5936 has requested it. Contact I.D. Uses Programmed Reporting Codes. The Contact I.D. communications format will use programmed reporting codes when transmitting to the central station. Contact I.D. Uses Automatic Reporting Codes. The Contact I.D. communications format will use the automatic reporting codes as shown in Appendix C when transmitting to the central station.

OFF I.D. Tone Frequency DLS Window ON OFF ON OFF

FTC Bell

[703] - Delay Between Dialing Attempts For standard (force) dialing, the panel will go off-hook, search for dial tone for 5 seconds, hang-up for 20 seconds, go off-hook, search for dial tone for 5 seconds, then dial. If there is no initial handshake recognized within 40 seconds, the panel will hang up. This programmable timer
adds a delay before the next call is attempted, and is defaulted to 001 for a total of six seconds.
5.10 Module Programming PWS Sect 10
The programming sections listed below pertain to additional modules on the system. For instructions on programming these modules and a description of each programming section, see the associated Installation Manuals. 43
1. PC5400 Programming Section [801] 2. PC5936 Programming Section [802] PC5936 audio interface will allow you to connect to 16 Interior (PC5921) or exterior (PC5921EXT) Intercom Station. These surface mounted stations contain a speaker and a microphone. This module enables Page/ Answer, Do Not Disturb, Baby Monitor, Answer Incoming Calls, Doorbell Function, and Background Music features in your alarm. This module also has the Listen-in feature for central station monitoring. The central station can select the audio station, listen/talk, extend on-line time and hang up. The Listen-In feature can be enabled separately for telephone numbers 1/3 and 2. All Talk/Listen and/or video sessions will be disconnected if the panel needs to communicate alarms to the central station.
Alternate Communicator Programming Section [803] PC5132 Programming Section [804] PC5100 Programming Section [805] PC5108L Programming Section [806] NOTE: All Talk/Listen and/or video sessions are disconnected when the panel communicates alarms to the central station. T-Link Programming Section [851] NOTE: Option [5] in Section [382] must be enabled to access this section. The T-Link module can be used to communicate panel events in SIA format over a Local Area Network (LAN). It can also be used for downloading (this requires DLS-3 v1.3).
Telephone 1 & 3 Listen-In Enabled. Section [381], Option 5 Telephone 2 Listen-In Enabled. Section [381], Option 6
Periodic Camera Test When the Periodic Camera Test option is enabled, the panel will test cameras connected to a PC5108L module every 30 minutes. Only cameras with the Camera Test option enabled will be tested. See your PC5108L Installation Manual for more information on camera tests. If the Local Mode option is ON, the panel will send events to the PC5108L module, Downlook will not be initiated if requested. If the Local Mode option is OFF, the panel will send communicated events to the PC5108L module. Downlook will initiate when requested. See your PC5108L Installation Manual for more information.See Periodic Camera Test Section [017], Option [7] and Local Mode Enabled/Disabled Section [381], Option [8]

120VAC 60Hz PRIMARY

*300mA (max), 5VDC Supervised
FTC Frost 3716 16.5VAC 37VA (min)
Do not connect to receptacle controlled by a switch
DEVICE DEVICE DEVICE DEVICE
To +AUX To +AUX To +AUX To +AUX
PGM 1: 50mA Max.* PGM 2: 300mA Max.(supervised) PGM 3: 50mA Max. PGM 4: 50mA Max.

Connect to local phones

To PC5700 Fire Module
Refer to the PC5700 Installation Instructions Part #29005063
4-WIRE SMOKE DETECTORS Smoke Detector must be latching type (DSC MN240 Series). To reset smoke detectors, enter [] [7] [2].

Zone Input

+ AUX 1 PGM 2
Compatible signalling device: Wheelock Model 34T-12-R (UL-Listed)
Supplementary Bell Circuit (Supervised for non-fire use only)
BELL / SIREN 12VDC 700 mA MAXIMUM
OBSERVE POLARITY Power limited access Power limited access
RM-1 POWER LOOP SUPERVISORY RELAY
Zones 1-8 of PC5020 or Zones 1-4 of PC5700
COM BLK 12VDC 35mA maximum WHT
SMOKE DETECTOR POWER 12VDC

NO ALM

*NOTE: AUX+ is shared between AUX+,
Keybus, (Red, Blk, Yel, Grn) and all PGM outputs. Minimum system required: One LCD5500Z keypad (85mA) and one PC5700 (150mA) or T-Link (150mA). Available current for AUX+, Keybus & PGM should total 180mA.
PC5020 CONTROL PANEL WIRING DIAGRAM
ALARM INITIATING LOOP RESISTANCE: 100 GRN
LATCHING 4-WIRE SMOKE DETECTOR (DSC MN240 SERIES)
EOLR-2 END OF LINE RESISTOR 5600 0.5W
Refer to installation guidelines in Installation Manual & detector manufacturer's literature when locating smoke detectors.
For max. loading, refer to the Battery Calculation Charts part# 29005057
IMPORTANT: A minimum of 1/4" (7mm) separation must be maintained at all points between power limited wiring and all other non-power limited wiring and connections. Wire entry for power limited wiring must be separate from non-power limited wiring.
Non-power AC IN limited access ONLY

2-WIRE SMOKE DETECTORS

Compatiblity Identifier: PC5-2 Maximum Operating Voltage: 13.75VDC Maximum Circuit Resistance: 100 (total) Do not mix different models on the same circuit, as the correct operation may be impaired. NOTE: The PC5020 is capable of a maximum of three 2-wire smoke detectors in the alarm condition.

+ BELL -

1 PGM 2

16VAC 37VA

(2)12V 7Ah battery (not supplied)
2200 END-OF-LINE RESISTOR EOLR-3

Voltage Barrier

Refer to the 2-wire smoke detector compatibility chart in the manual. NOTE: For PGM2 only.

PGM CONNECTIONS (1-4)

FCC Reg. No.: F53CAN-34330-AL-E REN=0.1B Plug Type: RJ-31X

Made in Canada

TABLE 1
Refer to the PC5020/PC5020CF Installation Manual P/N 29005907, Instruction Manual P/N 29005909. The PC5020 is UL Listed for limited energy installations per NEC Article 760. Recognized limited energy cable should be used. Observe NEC wiring requirements and local codes defined by the authority having jurisdiction. Printed information describing proper installation, operation, testing, maintenance, evacuation planning, and repair service is to be provided with this equipment. Security detection devices that require power from the control panel must be UL Listed for the intended application and operate over the range of 10.0 to 14.0 VDC. The DSC Bravo Series is a recommended UL Listed motion detector. Temperature Range: 0C to 49C (32F to 120F) Maximum Humidity: 85% relative humidity Control panel is suitable for the following UL installations: Grade AA Central Station and Grade AA Police Connect with high line security (using TLink to communicate to Sur-Gard MLR-IP receiver) Household Fire and Grade A Household Burglary & Home Health Care Signaling Equipment Grade A Local Grade B Central Station and Grade A Police Connect with basic line security Grade C Central Station and Grade A Police Connect with basic line security
(a) The delay (power-up) (start-up) time marked on the installation wiring diagram of the smoke detector or on the installed smoke detector(s) is to be used.
NOTE: For ULC installations, please refer to the ULC Wiring Diagram part#18006238 and the ULC Installation Information Sheet part#29002157.

Wiring Diagrams

B.2 PC5020CF and PC5700 Fire Module Communications Connections

PC-LINK Connection

PC5020

To Local Phones

B.3 Battery Lead and AC Power Lead Routing for Central Station Fire Monitoring Systems
POWER LIMITED POWER LIMITED

Control Panel PC5020

WARNING: Do not route any wiring over circuit boards. Maintain at least 1" (25.4mm) separation.

Cable Tie

KEYBUS

Power Limited

Cable Tie (not provided)

Class2 Power Limited

To prevent wires from falling onto batteries, secure them to the enclosure or to the plastic standoff located under the control panel.

Non-Power Limited

For fire installations, lines comethrough conduit connections.

37VA +

Voltage Barrier NON-POWER LIMITED

Incidence of Harm

If this equipment PC5020 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment PC5020, for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user. Simplex Time Recorder Co. 100 Simplex Drive, Westminster MA 01441-0001 USA, Tel: (978) 731-2500

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this number must be provided to the Telephone Company. FCC Registration Number: F53CAN-34330-AL-E REN: 0.1B USOC Jack: RJ-31X

Additional Information

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialing equipment for you.