About Your New Labelmaker
With your new DYMO LabelPOINT 350 labelmaker, you can create a wide variety of highquality, self-adhesive labels. You can choose to print your labels in many different sizes and styles. The labelmaker uses DYMO D1 label cassettes in widths of 6 mm (1/4), 9 mm (3/8), 12 mm (1/2), or 19 mm (3/4). Label cassettes are also available in a wide range of colors. Visit www.dymo.com for information on obtaining tapes and accessories for your labelmaker.
Figure 2 2. Insert the batteries following the polarity markings (+ and ). 3. Replace the battery compartment cover. Remove the batteries if the labelmaker will not be used for a long period of time.

Warranty Registration

Please complete the warranty registration card and return it to the appropriate customer service address within seven days. Visit www.dymo.com for details.

Using the Battery Pack

An optional, rechargeable battery pack can be used to power the printer. The battery pack can be purchased through your local DYMO reseller. The printer must be connected to external power through the AC adapter to charge the battery pack. When the battery pack is completely discharged, allow four to 2 hours to fully charge the battery. When connected to external power, the battery charging indicator may continue to display even though the battery pack is fully charged. To use the battery pack 1. Open the battery compartment door. 2. Insert the battery pack. See Figure 3.

Getting Started

Follow the instructions in this section to print your first label.

Connecting the Power

The labelmaker is powered by standard batteries, a rechargeable battery pack, or an AC power adapter. To save power, the labelmaker will automatically turn off after two minutes of inactivity.

Inserting the Batteries

The labelmaker uses six AA batteries. To insert the batteries 1. Remove the battery compartment cover. See Figure 2.
Figure 3 3. To charge the battery pack, connect the AC adapter as described below.
Connecting the Power Adapter
An optional AC power adapter can also be used to power the labelmaker. Connecting the AC adapter to the labelmaker disconnects the batteries as a power source. To connect the power adapter 1. Plug the power adapter into the power connector on the top, left side of the labelmaker. 2. Plug the other end of the power adapter into a power outlet. Make sure the labelmaker power is turned off before you disconnect the power adapter from the main power source. Otherwise, your most recent memory settings will be lost.

Remove cardboard insert

Select tape cassette size
Figure 5 2. Set the cassette switch for the size of the label cassette that you are inserting. See Figure 5. A notch in the cassette fits over the switch when the cassette is in the correct position. 3. Make sure the tape and ribbon are taut across the mouth of the cassette and that the tape passes between the guideposts. If necessary, turn the spool clockwise to tighten the ribbon. 4. Insert the cassette with the tape and ribbon positioned between the print head and pinch roller. See Figure 6.

Inserting the Label Cassette
Your labelmaker comes with one label cassette. Visit www.dymo.com for information about purchasing additional label cassettes. To insert the label cassette 1. Press and release the label cassette cover to open the label compartment. See Figure 4.

CLICK!

Figure 4 The first time you use the labelmaker, remove the protective cardboard insert from between the print head and pinch roller. See Figure 5.
Figure 6 5. Press firmly until cassette clicks into place. 6. Close the label cassette cover and press A to turn on the power.

Settings

You can select the language and corresponding units of measure you want the labelmaker to use.
The A button turns the power on and off. After two minutes of no activity, the power is switched off automatically. The last label created is remembered and displayed when the power is turned back on. The previously selected style settings are also restored.

Selecting a Language

You can select from a number of different language options. By default, the language is set to English. To select a language 1. Press Language. 2. Use the arrow keys to select the language you want and press OK.

LCD Display

The labelmakers LCD display shows a row of sixteen characters. However, you can enter up to 99 characters and spaces. The display is similar to a window that scrolls across the text. (See Figure 7.) The number of characters actually displayed can vary due to proportional spacing. The quick brown fox jum over the lazy dog. jumps Figure 7 In addition, feature indicators appear on the display to let you know when a feature is selected. See Figure 8.

Font Style Scroll Bar

Selecting Units of Measure
You can choose to show measurements in inches or millimeters. By default, the units of measure are set to inches. To set the units of measure Memory 1. Press Settings. 2. Use the arrow keys to select Set Units and press OK. 3. Select inches or millimeters and press OK.
Printing Your First Label
You are now ready to print your first label. To print a label 1. Enter text to create a simple label. 2. Press G. 3. Use the cutter lever to cut the label. Congratulations! You have printed your first label. Continue reading to learn more about the options available for creating labels.

Mixed Formats

CAPS mode

Multiple Lines

Fixed Length

Align/Justify

Getting to Know the Labelmaker
The following sections describe each feature in detail. Become familiar with the location of the feature and function keys on your labelmaker. See Figure 1 on page 2.

Figure 8

Box/Underline

# of Copies

CAPS Mode
The # key toggles capitalization on and off. When CAPS mode is turned on, the CAPS mode indicator is shown on the display and all letters that you enter will be capitalized. The default setting is CAPS mode on. When CAPS mode is off, all letters entered appear in lower case.
Connecting to Your Computer
Your labelmaker can be used as a standalone label printer or you can print labels from your computer using the DYMO LabelMANAGER software. Your labelmaker connects to your computer using the USB connection located on the top of the labelmaker. See Figure 9.

Shift Key

The 8 key, when used in combination with an alphabet key, changes the case of the selected letter. When used in combination with number keys or function keys, the 8 key selects the alternate function shown on the key. For example, when you press 0, the character to the left of the cursor is deleted; however, when you press 8 + 0 together, the entire label text and formatting is deleted and the display is ready for you to type a new label.
Figure 9 Refer to the LabelPOINT 350 Quick Start Card for installation instructions and the DYMO Label Software User Guide for information about designing and printing labels.

Space Bar

The V inserts one or more blank spaces in your text.

Formatting Your Label

You can choose from a number of formatting options to enhance the appearance of your labels. The labelmaker remembers the last selection made so that each time you enter one of the feature menus described in this section, you are positioned at the last item selected from that menu.

Backspace

The 0 key removes the character to the left of the cursor. Pressing 8 + 0 clears all label text and formatting.

Cancel

The Cancel key allows you to exit from a menu without making a selection or to cancel an action.

Changing the Font Size

Seven font sizes are available for your labels: Arial Narrow Arial Normal Arial Wide Times New Roman

Navigation Keys

You can review and edit your label using the left and right arrow keys. You can navigate through menu selections using the up and down arrow keys, and then press OK to make a selection.
When you select a font, that font applies to all characters on a page. If you want to use more than one font, you must insert format breaks. See Using Mixed Formats on page 8 for more information. To set the font 1. Press the key. 2. Use the arrow keys to move to the desired font and then press OK.
Styles can be used with all alphanumeric characters and symbols. See Using Symbols and Special Characters on page 8 for more information on printing symbols. To set the font style key. 1. Press the 2. Use the arrow keys to move to the desired style and then press OK.

Adding Font Styles

You can choose from thirteen different font styles to apply to your text: Normal Vertical Italic Bold Outline Shadow 3D Italic + Bold Italic + Outline Italic + 3D Italic + Shadow Strike-through Mirror Figure 10 When you select a style, that style applies to all characters on a page. If you want to use more than one style, you must insert format breaks. See Using Mixed Formats on page 8 for more information. However, when you use mirror or vertical style, that style applies to the whole label.
Adding Box and Background Styles
You can further highlight your text by choosing a box, underline, or background style. Normal DYMO Underline Square Box Pointed Box Rounded Box Crocodile Box Scroll Box 3D Box Dots Wood Grain Bricks Checkers Parquet Diamonds Weave Figure 11
DYMO DYMO DYMO DYMO DYMO DYMO
A label can be underlined or enclosed in a box or background, but not both together. To set the box style 1. Press the key. 2. Select a frame style and then press OK. On multi-line labels, all lines are underlined. However, all the lines are enclosed in a box style.
Creating Multiple-Line Labels
The number of lines you can print on a label depends on the size label tape you are using: Maximum of five lines on 19 mm (3/4") labels Maximum of three lines on 9 mm (3/8") and 12 mm (1/2") labels Maximum of one line on 6 mm (1/4") labels To create a multiple-line label 1. Type the text for the first line, and press 7. A new line character is displayed at the end of the first line, but will not print on the label. 2. Type the text for the second line. The display shows the line on which you are currently entering text. The example below indicates that the second line is the current line on the label. Use the arrow keys to move between lines.

To add a format break 1. Enter and format text for the first section. 2. Press Insert. 3. Select Insert Format Break and press OK. A new section character is displayed at the end of the first section, but will not print on the label. 4. Continue entering and formatting text for the next section of the label.

Using Tabs

You can add tabs to a label to align text on multiline labels. Tabs are left justified and the default spacing is 50 mm (2.0). To change the tab spacing Memory 1. Press Settings. 2. Select Set Tab Length and press OK. 3. Use the up and down arrow keys to increase or decrease the tab setting, and then press OK. To insert a tab 1. Enter your text. 2. Press the key and continue entering text.
Using Symbols and Special Characters
Symbols and other special characters can be added to your labels.

Using Mixed Formats

You can apply different fonts and format styles to the text on a label by inserting format breaks to divide the label into blocks or sections of text. You can add two format breaks allowing you to apply three separate formats per label. Alignment, underline, box styles, and background patterns cannot be mixed on a label. These styles are common to the entire label.

Adding Symbols

The labelmaker supports the extended symbol set as shown in Figure 12.
To add a symbol 1. Press Symbols. The first row of symbols shown in the table appears in the display. 2. Use the arrow keys to move to the desired symbol. The left and right arrows move horizontally along a row of symbols. The up and down arrow keys scroll vertically through the rows of symbols. To quickly see a row of symbols, you can press the letter corresponding to the row you want. 3. When you locate the desired symbol, press OK to add the symbol to your label text.
Adding International Characters
The labelmaker supports the extended Latin character set using RACE technology. Similar to using a mobile phone keypad, if you type a letter multiple times within a very short time, you will scroll through variations on that letter. For example, if French is selected as the language and you repeatedly press the letter a, you will see a and so on through all the variations available. The character variations and the order in which the variations appear depend on the language you have selected to use.

Currency Symbols

The currency key also uses RACE to scroll through a number of currency symbols:
The order these symbols appear depends on the language you have selected.

Printing Options

Figure 12 You can print multiple copies of a label at one time, print serialized labels, print fixed-length labels, review label text and format, and adjust the printing contrast.

Printing Multiple Copies

You can print up to 16 copies of a label at one time. When printing multiple copies, a dotted cut-line is printed between each label. To print multiple copies of the label Memory 1. Press Settings and then select Set # Copies. 2. Press the up arrow key to increase the number of copies to print. 3. Press the down arrow key to begin decreasing the number of copies from 16. 4. Press OK. 5. Press G to begin printing. When printing is finished, the number of copies to print returns to the default value of 1.
You can specify a fixed length for a label in 2 mm (0.1) increments between 40 mm (1.5) and 400 mm (15.0). The preset fixed length is 100 mm (4.0). Any change you make to the fixed length setting remains in effect until you change it. To set the label length. 1. Press 8 + 2. Select ON to turn on Fixed Length. 3. Press the up arrow to increase the length. 4. Press the down arrow to decrease the length. 5. Press OK to set the fixed length. 6. After you print the label, repeat step 1 and turn Fixed Length OFF; otherwise, all your subsequent labels will print with this fixed length.

Serializing Your Labels

You can print a series of labels with the last number incremented by one number. The number of labels serialized depends upon the number of copies you selected to print. Only the last series of numbers that follows any letter, space, or punctuation will be serialized. For example, abc123 will print as abc123, abc124, abc125; and 123-998 will print as 123-998, 123-999, 123-1000, and so on. To serialize your labels 1. Enter the text for your label. 2. Select the number of labels to print as described in Printing Multiple Copies on page 10. 3. Select 8 +.

Printing Barcode Labels

The labelmaker can print barcodes in six standard formats: UPC A, UPC E, EAN8, EAN13, CODE-39, and CODE-128. You can only print a barcode on 19 mm (3/4) label tape; and you can only print one barcode per label. The barcode prints horizontally along the label with the text in small print underneath the barcode. You can optionally add text before and after the barcode. Or, you can add text above or below the barcode by creating a two-line label. See Creating Multi-Line Labels on page 8. Four of the standard barcodes require a fixed number of characters to generate the barcode: EAN-8, EAN-13, UPC-A, and UPC-E. CODE-39 and CODE-128 barcodes allow a variable number of characters to be entered. To set a barcode Memory 1. Press Settings. 2. Select Set Bar Code and press OK. 3. Use the arrow keys to select the barcode type, and press OK.

Printing a Fixed Label Length
Normally, the length of the label is determined by the length of the text entered. However, you may wish to make a label for a specific purpose that is a fixed length regardless of the length of the text.
4. One or more question marks appear between the barcode symbols ( ).
3. Press 0 to turn off the alignment setting.

???????0

You may see a 0 in the far right position for some barcode types. This is a check digit and will be replaced with a number when the barcode data is entered. 5. Enter the data for the barcode, replacing the question marks, and press OK when finished. To insert a barcode 1. Enter the text you wish to appear before the barcode on the label. (optional) 2. Press Insert. 3. Use the arrow keys to select Insert Barcode and press OK. 4. Enter any text you wish to appear after the barcode. (Optional) 5. Press.
Adjusting the Print Contrast
You can adjust the print contrast to fine tune the print quality of your label. To set the contrast Memory 1. Press Settings. 2. Select Print Contrast and press OK. 3. Select a contrast setting and press OK.

Using Labelmaker Memory

The labelmaker has a powerful memory feature that stores text and formatting as follows: Automatically stores the last fifteen labels printed. Allows you to store the text of up to ten labels you use frequently. Allows you to name and store up to ten commonly used label formats.

Previewing Your Label

You can preview the text or format of your label prior to printing. A two-line label is previewed as a single-line label. To preview your label 1. Press 8 + Insert. 2. Select Text or Format. If you select Text, the text of the label scrolls across the display. If you select Format, the format selected displays briefly.

Storing Label Text

The labelmaker automatically keeps the last ten labels printed in a text buffer. In addition, you can store up to ten specific labels you use frequently. To store the current label text Memory 1. Press 8 + Settings. 2. Select SAVE and then LABEL. The first of ten memory fields is displayed. 3. Use the arrow keys to move through the fields. You can store new text in any of the memory locations, however, if you select a location that is filled, the previous label text will be overwritten. 4. Select a memory location and press OK. Your label text is saved and you are returned to the label.

Aligning the Text

When you print a fixed length label you can choose to align the text at the left, center, or right side of the label. For multi-line labels, all lines of text are aligned left, center, and right relative to each other. To align the text. 1. Press 8 + 2. Select the desired alignment and press OK.

Storing Formats

In addition to label text, you can store up to ten specific label formats you use frequently. This feature stores only the formatting information not the label text. To store the current format Memory 1. Press 8 + Settings. 2. Select SAVE and then FORMAT. The first of ten memory fields is displayed. 3. Use the arrow keys to move through the fields. You can store a new format in any of the memory locations, however, if you select a location that is filled, the previously stored format will be overwritten. 4. Select a field and press OK. The word NAME? appears in the field. 5. Enter a name for the format and press OK. The label format is saved and you are returned to the label.
Caring for Your Labelmaker
Your labelmaker is designed to give you long and trouble-free service, while requiring very little maintenance. Clean your labelmaker from time to time to keep it working properly. Clean the cutter blade each time you replace the tape cassette. To clean the cutter blade 1. Remove the label cassette. 2. Press and hold down the cutter lever to expose the cutter blade. 3. Use a cotton ball and alcohol to clean both sides of the blade. 4. Release the cutter lever. You can also follow this procedure if the cutter blade becomes lodged in the forward position and will not move. To clean the print head Clean the print head using the cleaning tool located inside the tape compartment lid.
Recalling Stored Labels and Formats
You can easily recall labels and formats stored in memory to use at a later time. To recall labels or formats Memory 1. Press 8 + Settings. 2. Select Recall and then LABEL, FORMAT, or LAST PRINTED. The first memory location is displayed similar to storing a label or format. 3. Select a label or format to recall and press OK.

Troubleshooting

Review the following possible solutions if you encounter a problem while using your labelmaker.
Problem/Error Message No display Poor Print Quality Solution Ensure the labelmaker is turned on. Replace discharged batteries. Replace discharged batteries or attach power adapter. Ensure tape cassette is installed properly. Clean the print head. Replace the tape cassette.

Poor Cutter Performance Printing Too many characters Exceeded maximum number of characters in buffer. Too many lines Exceeded maximum number of lines allowed. Insert Tape Cassette Tape cassette missing or empty. Battery low Batteries almost discharged. Tape Jam Motor is stalled due to tape jam. Too many pages Exceeded masimum number of pages allowed. Page not empty Tape size too small Set Fixed-length label selected and the length necessary to print the label exceeds the selected length.
Clean the cutter blade. See Caring for Your Labelmaker. No action required. Message disappears when printing is finished. Delete some or all of the buffer text. Select another format. Insert a new tape cassette Replace batteries or connect AC power adapter. Remove jammed tape and replace tape cassette. Clean cutter blade. Change label layout. Delete all content on the page. Change label size or press Cancel to exit Box/Background menu. Following this message, a fixed-length value is displayed which indicates the minimum label length necessary to fit the text. Do one of the following: Adjust the fixed-length label setting appropriately, or Select a narrower font size.
If you still need assistance, contact DYMO Customer Support. Refer to Contacting Customer Support on page 63 to locate the contact number for your country.

Documentation Feedback

We are constantly working to produce the highest quality documentation for our products. We welcome your feedback. Send us your comments or suggestions about our user guides. Please include the following information with your feedback: Product name, version number, and page number Brief description of content (instructions that are inaccurate or unclear, areas where more detail is needed, and so on) We also welcome your suggestions about additional topics you would like to see covered in the documentation. Send email messages to: documentation@dymo.com Please keep in mind that this email address is only for documentation feedback. If you have a technical question, please contact Customer Support.
This product is CE marked in accordance with the EMC directive and the low voltage directive and is designed to conform with the following international standards: US FCC Class B Compatibility Safety - EN 60950, IEC 950, UL 1950 EMC Compatibility EN 61000 3-2/3; EN 61000 4-2/3/4/5/6/8/11; ENV 50204; EU Immunity - EN 55024 & addendums A1, A2 Electromagnetic Compatibility (EMC) - Information Technology equipment, Immunity Characteristics Emissions EN 61000-6-3: Electromagnetic Compatibility (EMC) - Part 6: Generic Standards - Section 3: Emission standard for residential, commercial and light industrial environments. Esselte is an ISO 14000 registered company. Plastic components of this printer have been marked to enable final disposal in a manner that is sensitive to the environment.

Features

PRINTING FONT, STYLES & EFFECTS Resolution Number of fonts Normal / Bold / Vertical / Outline / Shadow / Italic / Mirror / 3D / Strikethrough Underline Box Number of character sizes Number of print lines Last label Number of extra memories Automatic Number of batteries Battery type

LM 350D

180 dpi 6 6 AA

MEMORY TAPE CUT POWER

LabelManager 350D
Versatile desktop label maker to create and store many labels

Customize

Available tapes for LabelManager 350D
STANDARD D1 LABELS BLACK CLEAR

6/9/12/19 mm

BLACK W HITE

BLACK B LUE

9/12/19 mm

BLUE C LEAR

BLUE W HITE

BLACK R ED

RED CLEAR

RED WHITE

BLACK YELLOW

WHITE CLEAR

12/19 mm

WHITE BLACK

BLACK GREEN

D1 PERMANENT LABELS

D1 FLEXIBLE LABELS FOR CURVED SURFACES BLACK W HITE

Super fast & easy

Just type, customize, print, stick

Dealer

Produced by: DYMO bvba - Industriepark-Noord 30 - B-9100 Sint-Niklaas - Belgium A Newell Rubbermaid Company - www.sanfordbrands.com Made in Belgium - 2007 DYMO

S0820000

LabelManager 350D is the ideal desktop label maker for professionals expecting top quality labeling. The sleek looking and comfortably designed LabelManager 350D has numerous functions and options for customization.
VERSATILE AND PACKED WITH FEATURES The multifunctional LabelManager 350D is a must have for professionals demanding high quality. It has a wide range of functions, fonts and styles allowing you to create customized labels quickly. And the 350Ds extensive memory allows you to save numerous personal labels and preferences. Plus, you can also use a broad range of tapes in different colours and sizes up to 19mm wide.
QUICK GLANCE LABEL MAKER FEATURES Large semi-graphical display with print preview for convenient viewing and editing. Type-writer style keyboard for faster label input. Easy-to-use function keys and navigation pad. Quiet, automatic electric cutter.