Voice Commander / STARTING VOICE COMMANDER..12-2 VOICE COMMAND FORMAT..12-3 VOICE COMMANDER SETTINGS..12-5 Contacts Settings Page..12-5 Application Settings Page..12-8 Music Settings Page..12-10 Digit Training Settings Page..12-12 Advanced Settings Page...12-14 FAQ....12-15
Specifications / Regulation Notice and Safety Declaration / SAR INFORMATION...14-1 HEALTH AND SAFETY INFORMATION..14-2 FAQ /
1 Voice Command Satellite
Navigation Device Installation

Navigation /

Pocket PC Pocket PC Car Mount: place where it is easily accessible to driver or passenger Car Charger: when Pocket PC is low on power, recharge by connecting one end to the car cigarette lighter/12 volt power outlet and the other end to the socket on base of Pocket PC. Attention: The GPS signal receiver is built into the Pocket PC. If car windscreen has heat reflective metallic film, or Pocket PC is obstructed by objects, then the receptivity of the GPS will be adversely affected. Voice Command Satellite Navigation 1-1
GPS Navigation Software Installation
Please follow your car navigation system operating manuals instructions on software installation in order to use the navigation function.
Conditions for Using GPS Car Navigation
By using this system you are agreeing to the following conditions: 1. When using this device, please use with matching car mount. Affix device securely to the car mount. Please be aware that installation in the areas depicted below is forbidden and is strictly prohibited.
Do not place where it will obstruct driver vision Do not place over air bag Do not place where it can not be securely attached Do not place in path of activated air bag 2. Please set navigation destination before driving. Do not operate this system while driving. 1-2
3. Please use this system with care. If any harm results from careless use of this system, the responsibility for safe driving resides with the driver. 4. GPS positioning is limited by weather and usage location (tall buildings, tunnels, underpasses, trees, bridges). Most GPS do not work indoors, nor can GPS signals penetrate buildings, car sun shades and heat reflective film with metallic content. Please install GPS outdoors with clear line of sight. Beneath the windscreen at the front of the car is a common choice, and the windscreen should be free of heat reflective film. 5. If reception is poor, an external GPS antenna may give better signal reception. 6. The GPS system is built and operated by the U.S. Department of Defense which is also responsible for its maintenance and calibration. Any changes made by them may affect the operation and accuracy of the GPS system. 7. Wireless devices (mobile phones, speed radar detectors) will all interfere with the satellite signal and cause unreliable signal reception. 8. The GPS position fix is provided only for the drivers reference and should not affect actual driver behavior. 9. The electronic map data provided in the navigation system is for normal reference only and not intended for high precision applications. The user should determine their exact location based on actual road conditions. 10. The route provided by the navigation system, the audio cues and intersection data are derived from recommended optimal route calculated using the electronic map data. This is provided for the drivers reference only, the driver should decide their chosen route according to actual road conditions. 11. When not in use, please do not leave the device inside the car. If exposed directly to sunlight, the battery may overheat and cause damage to this device. This may endanger the vehicle as well. Voice Command Satellite Navigation 1-3

If you need to charge the main battery by itself, you can insert it into the charging slot at the back of the charger. The LED indicator on the side of the charger displays the charging status.
Charging Red LED lights up
Fully charged Green LED lights up

No battery LED is off

Re-installation or Replacing the Battery
If the phone or GPRS connection function is already activated, deactivate it first and run the next step; otherwise abnormal disconnection will occur. 1. Press the fixing lock button on the rear side of the Pocket PC and remove the back cover. 2. Slide the main battery lock down to open the main battery lock. Now you can easily remove the battery. 3. Replace the main battery and lock it properly. When you remove the main battery, the system operation will be powered temporarily by the backup battery. 4. Slide the back cover into the groove until you hear a click to indicate that the back cover lock is locked properly.

Unlock

Follow the directions in the figure to install or remove the battery properly. Back cover lock. Main battery lock. Slide down to unlock and slide up to lock. 2-8

Power On and Off

Power Button

Sleep Mode

1. Press the Power Button at the top of the Pocket PC to enter the Sleep mode. At this time, the screen is turned off and all peripheral devices enter the power-saving mode. But if the phone is turned on, it is still in the call waiting mode. 2. To turn on the screen later, just press the Power Button. 3. Tap , Settings, the System tab,
Power and then the Advanced tab to set the device to turn off automatically after waiting for a certain time period.

Turn on the Screen

This product is designed with a power-saving feature. If the screen is turned off, press the Power Button at the top of the Pocket PC to turn it on.
If the screen is too dark and you cannot see clearly, set the proper brightness level for the backlight. Here are two methods that you can use: 1. Long press Power Button to turn the backlight on or off. 2. Tap , Settings, the System tab,
Backlight and then the Backlight Level tab.
Using the Stylus to Touch the Screen Your Pocket PC is designed for graphics-based operation. Generally speaking, we usually use the stylus to perform basic actions such as tap, drag, and tap and hold on the touch screen. Other actions such as reset and cold boot will require the use of the stylus tip. Pull the stylus to full-length to make it easier to tap the screen during operation. When kept completely in the stylus holder, the stylus length shortens.

Tap Menu, Options, and then the Phone tab. You can set the ring type as ring, vibration or mute. If you want to use a customized ring tone file, use the ActiveSync program on your desktop computer to copy the.wav ring tone file to the /Windows/Rings folder on the Pocket PC. You can then select this ring tone from the Ring tone list. Set the key sound for dialing. You can set a PIN (Personal Identity Number) to block unauthorized access to your phone. Your first PIN is provided by your phone service provider.

Add Ringtone

Tap , Programs, Phone, and then Add Ringtone. 1. All of the music files stored in your Pocket PC or Mini SD card will be listed, please select the new ringtones which you would like to add. 2. Tap Add Ringtone Button, then you can enter the Phone tab for telephone environment settings and select your ringtone files from the Ring tone list. 4-12
Phone Application Programs
Caution! Before you can use the functions described in the Phone Group. Make sure that the SIM card is properly installed in your Pocket PC and the Phone is already turned on.

SIM Tool Kit

Tap , Programs, Phone, and then SIM Tool Kit.
This screen is for reference only. The actual screen is based on the service items provided by your telecom company.
Tap any service item. Select Button: Launch service item. Follow the screen or voice instructions.

SMS Sender

Tap Tap , Programs, Phone, and then SMS Sender. , Messaging, and then New.
Enter the composing SMS screen in Messaging.
Text Messages means you are editing SMS. Input the mobile phone number. Input the messages you want to send. Tap Menu and then My Text to select canned messages or to edit your Text Messages. Tap to send SMS message.

Speed Dial

Tap , Programs, Phone, and then Speed Dial.

Hot Key Switch

Tap the box according to the functions provided by the system. View Button: to switch between these functions: Frequency Dial Index Dial. Tools Button: Provides the relevant menu. For example, select Settings to set the interface as Frequency Dial or Index Dial. Select Sound on/off to set the sound for tapping the screen.
Tap Tools and then Color and Text to enter the Setting screen shown on the left. You can set the text font, text color and button background color according to your personal preferences. Font Text color Button background Preview area

Frequently Dialed Screen

Frequency Dial screen
Tap View Button to switch to the Frequency Dial screen as shown on the left. Tap any phone entry box to speed dial. Tap and hold the box, then select appropriate command from the pop-up menu. Sort according to the number of calls in descending order. The upper left corner has the most number of calls while the lower right corner has the least number. : Tap to view the previous or next page.

Index Dial

Index Dial screen Tap View Button to switch to the Index Dial screen as shown on the left. Tap on any letters. The content displayed are the data created in Contacts. If you did not create any data in Contacts, the screen is blank.
The letter F appears on the upper left side of the screen (see left). This indicates that this page contains all address data that starts with F. The English Address Book is arranged alphabetically using the First Name. Tap any box to speed dial. : Tap to view the previous or next page.

Call Filter

Tap , Programs, Phone, and then Call Filter.

Add New List Button to

add a new Block List. Tap and hold an entry in the list. Select from the pop-up menu to manage the list according to your needs. Tap Add New List to add a
new Allow List. Tap and hold any entry in the list to display the pop-up menu. Add New List Button Call History Button: Blocked call records. Options Button
Synchronize Button: Tap Options and then Synchronize to activate the functions for this button. The system will synchronize the names according to the current Contacts entries but without updating the phone numbers. Find Button: Helps you find entries conveniently if there are lots of entries in the list. About Button: Information about Call Filter.
Tap Add New List Button in the Call Filter screen to enter the screen shown on the left. Input name and telephone number. Add to Block List or Allow List. OK Button Cancel Button Tap and hold a contact in the Contacts screen. Select Add to Call Filter from the pop-up menu to add a new entry to the Block List.
Tap Options Button in the Call Filter screen to enter the screen shown on the left. Call tab: Set to accept or reject call. History tab: Set the time for keeping the record. Synchronize tab: Activate or deactivate the functions of Synchronize Button in the Call Filter screen. Status tab: Set to activate or deactivate the Status icon on the lower right of the Today screen. If or activated, the icons will show. Tap to view the filter status.

Tap the icon

on the lower right of the Today screen
to display the Call Filter Status window.
Display Call Filter setting status.
Tap to hide the Call Filter Status window.

5 Customize

Your Pocket PC /
You can adjust the Pocket PC settings according to your personal preferences and install other programs.

Connecting Directly to the Mail Server
For single-machine use, not combining office and home E-mails, please refer to E-mail Server Setup section.
You will receive messages directly from the mail server. This is irrelevant to personal computer use. You can work online or offline. When working online, you read and respond to messages while connected to the e-mail server. Messages are sent as soon as you tap Send, which saves space on your Pocket PC.
When working offline, once youve downloaded new message headers or partial messages, you can disconnect from the e-mail server and then decide which messages to download completely. The next time you connect, Inbox downloads the complete messages youve marked for retrieval and sends the messages youve composed.
Based on your preference, you can program the Pocket PC to receive mail for the last few days, receive subjects only or the entire mail, or just receive mail with file attachments smaller than a specified size. If you want to receive more or less mail, tap Menu, Tools and then Options to adjust the E-mail account settings according to your needs.
Sending and Receiving Messages

E-mail Server Setup

Refer to this section if you are preparing for single-machine use and not combining office and home E-mails. If you already have an E-mail account from your ISP or company network, you can use Messaging to send and receive mails and messages. To establish a new Messaging E-mail server on your Pocket PC, refer to the following sections. 1. Obtain the following information from your ISP or companys network administrator for convenience in setting up the E-mail service. E-mail address, account name and password POP3 or IMAP4 server name for internal mail SMTP server name for sending mail 2. E-mail Setup: Tap ,
Messaging, Menu, Tools, and then New Account to display the screen on the left. Follow the screen instructions to set up the E-mail service. 3. Refer to Connecting to the Internet section to connect the Pocket PC to the Internet and you can start sending and receiving E-mails and SMS messages. 4. Connecting to the E-mail server: Tap Messaging, Menu, Switch Accounts, and then check POP3. Tap Menu and then Send/Receive. Tap Menu, Tools and then Options to change the E-mail setup. 8-4

Using E-mails and SMS

Below is a brief description of the Messaging screen functions:
Select the service and folder you want to display. Select the sort order for messages. Tap to open a message. Tap and hold to display a pop-up menu of actions. Status bar Tap to change the account settings. Tap to compose a message.
Brief description on writing, sending, reading and replying (to) mail: 1. Send and Receive Mail: Tap New to compose a message and then tap Send to send it.
Tap To, Cc or Bcc to open the Contacts screen. As long as you have set up Contacts beforehand, you can just tap to select. Tap the data area to input the E-mail adress, mobile phone number and subject directly. If there is more than one contact, use a semi-colon (;) to separate the addressees. POP3 means to send E-mail, and Text Messages means to send an SMS message. Note that the same message cannot be sent as E-mail and SMS message at the same time. Use the scroll bar to view the header. Menu Button: Provides frequently-used functions for writing mail such as request return receipt, attach files to E-mail, select canned messages, edit canned messages or cancel mail. Send Button: Send your messages.
2. Read and Reply: Receive new mails by tapping Menu and then Send/Receive. Switch to the Inbox folder and tap to open. The following figure shows the open mail screen.
Besides reading the messages, provide frequently-used functions for replying to or forwarding.
3. Change preference settings. Set the Inbox Synchronization option under ActiveSync. Tap Messaging, Menu, Tools, Options, and then the Accounts, Messagetabs on the Pocket PC to set the appropriate options.

MSN Messenger

On the Today screen, tap screen. Tap , Programs, Pocket MSN, and then MSN Messenger. to display the MSN Messenger sign-in
To switch to MSN Messenger, tap

, Programs, and then tap

Pocket MSN. MSN Messenger on your Pocket PC is an instant messaging program that lets you:

Tap Messaging

Tap to change the MMS sort method. Select the folder types you want to display in the list. Tap to manage your MMS mailbox. Tap to add a new MMS. Provides the relevant menu.

Setting Up MMS Mailbox

You must first apply for GPRS services with your telecommunications service provider. Usually, MMS service comes with GPRS, but this may still depend on your particular service provider and the services that they offer. Please check the detailed information provided by your service provider. After you have performed the complete configuration process, go on to the Create and Edit MMS section and try out the easy to use yet exciting multimedia MMS which has abundant audio and video special effects. , Settings, the 1. Tap Connections tab, Connections, the Tasks tab, and then Add a new modem connection. Refer to the information provided by your service provider to create a new GPRS connection. 2. This is exclusively for MMS usage, therefore the Server name for the MMS server setting must correspond with the Connection Name shown in the screen on the left. 3. Continue and tap the Advanced tab in Connections, and then tap the Select Networks Button. 4. Make sure that the upper item in the screen on the left has been set to My ISP.
, Messaging, Menu, 5. Tap Switch Accounts, and then check MMS.
6. Tap Messaging, Menu, MMS Configuration, the Servers tab, and then New Button. The screen displays shown on the left. 7. Refer to the information provided by your service provider and enter the information accordingly, then tap OK Button to save. 8. The Server Name that you enter in the screen shown on the left should be the same as the Connection Name that you entered for the Add a new modem connection. settings in Connections. 9. The Internet should be selected for Connect via.
10. Select the item that you have just saved, then tap the Set As Default Button. 11. Now you have completed the MMS configuration process.

Create and Edit MMS

How to add a new MMS: 1. Select MMS Composer to display a MMS template that you can edit freely. 2. Tap specified areas to insert the desired picture, text and audio files. Tap Send button to send the MMS messages. Tap To button to select a phone number or E-mail address from your Contacts. You can tap the entry area to input the phone number or E-mail address also. Tap to show or hide the complete header. Tap to input the subject.
Tap the specified area to insert the desired picture file. The next screen will display the current available files. You can use the pull-down menu on the upper left corner to change the folder path. The pull-down menu on the upper right corner allows you to select a picture file to be inserted. Select the desired picture file and tap to insert. Tap the text dialog area, edit MMS text and then just tap. How to use Canned Text: Tap to insert pre-saved expressions and phrases. In addition, if you tap and hold on the canned text screen, then tap New on the pop-up menu, you can create your own canned text. Tap the specified area to select the audio to be included in the MMS. After selecting the required file, tap. Note: Only one audio file is allowed for each slide. Tap to view the other slides you created. Preview Button Options Button: Set your favorite MMS options. 8-16

Multimedia Manager

Tap , Programs, Multimedia, and then Multimedia Manager.
You can use Multimedia Manager to manage and view multimedia information such as pictures, music, videos, etc.
Preview Multimedia Information
Select the folder you want to display. Tap to change the order of the list. Preview thumbnail. Set according to the multimedia information placed in the folder. If you are browsing pictures, tap a thumbnail to display the full picture. If you are browsing music or video, tap a thumbnail to play. Tap and hold the thumbnail and when the pop-up menu appears, select the desired functions. View Button: Select other types or auto-play pictures as a slideshow. Tools Button: Create new folders, link to other usable programs and set the viewing method. Show Type Button: Select to display as large or small picture and the number of pictures per row. Tap to the upper directory.

Slide Show Function

Tap Multimedia Manager, View, and then SlideShow.
Double tap anywhere on the screen to exit the slideshow. Playing the last picture while not in the slide show looping mode, tap the screen and then tap the icon to exit the slideshow. Refer to the method described above to exit the slideshow and enter the screen shown on the left. Select the picture scale, rotation and view picture properties. Link to other available programs. Full-screen view. To exit full-screen mode, tap the screen and then tap the icon on the
lower left corner of the screen. View the previous or next picture. Enlarge or shrink to the suitable screen size. Zoom in or out.

Multimedia Manager Tools

Tap Multimedia Manager, Tools, and then Setting. Slideshow tab: As shown on the left, this is the settings of the slideshow mode. Association tab: Select the desired file type you want to open with Multimedia Manager. File Browse tab: Set the browsing method. Tap Multimedia Manager, Tools, and then Delivery. Tap thumbnail. The in the upper
left corner indicates that it is already selected. Next: Select the program to link to. For example, if you select Image Maker, you will go to Image Maker.

Image Maker

Tap , Programs, Multimedia, and then Image Maker.
Image Maker is used to create, edit and view pictures. Use it to view and edit the pictures you take. You can also use the relevant Image Maker commands and tools such as rotate, stretch, brightness, etc. to edit and process the graphics.
Drawing tool box. Tap to utilize more drawing tools. Drawing or image editing area. When the image file exceeds the viewing range of the editing area, tap the scroll button on the right or bottom of the screen. File Button: Provides file management function such as opening and saving files. Edit Button: Provides editing functions such as undo, copy and paste, etc. Image Button: Provides special effects for pictures.

For more information about using Windows Media Player for Pocket PC, tap , and then tap Help.

Internet Explore

Using Internet Explore
Use Microsoft Internet Explorer Mobile to view Web or WAP pages in either of these ways:
During synchronization with your desktop computer, download your favorite links and mobile favorites that are stored in the Mobile Favorites subfolder in Internet Explorer on the desktop computer. Connect to an Internet service provider (ISP) or network and browse the Web. To do this, youll need to create the connection first, as described in Connect to the Internet.
When connected to an ISP or network, you can also download files and programs from the Internet or intranet. To switch to Pocket Internet Explorer, tap Explorer. and then Internet

Browse the Internet

Refer to Connecting to the Internet section to connect the Pocket PC to the Internet and start browsing websites. 1. Tap and then Internet Explorer.
2. Input the site address into the address bar at the top of the screen and connect to this site. 3. Use the scroll bar at the right side or bottom of the screen, or press the up or down button on the Pocket PC to view the contents of the entire website. Input address here Tap to launch Back Button Provides the relevant menu, such as Favorites, Add to Favorites, Home, and Refresh.
Aside from keying in the address directly, you can also connect to websites using the following methods. Tap the Favorites button, and then tap the favorite you want to view. In the address bar, tap the arrow to choose from previously entered addresses. To add a favorite link while using the Pocket PC, go to the page you want to add, tap and hold on the page, and tap Add to Favorites. Companion Programs 10-25
View Mobile Favorites and Channels
Tap the favorite you want to view. Tap to add or delete a folder or favorite link.
1. Tap the Favorites button to display your list of favorites. 2. Tap the page you want to view.
Youll see the page that was downloaded the last time you synchronized with your desktop computer. If the page is not on your Pocket PC, the favorite will be dimmed. You will need to synchronize with your desktop computer again to download the page to your Pocket PC, or connect to the Internet to view the page.
The Mobile Favorites Folder
Only items stored in the Mobile Favorites subfolder in the Favorites folder in Internet Explorer on your desktop computer will be synchronized with your Pocket PC. This folder was created automatically when you installed ActiveSync.

Favorite Links

During synchronization, the list of favorite links in the Mobile Favorites folder on your desktop computer is synchronized with Pocket Internet Explorer on your Pocket PC. Both computers are updated with changes made to either list each time you synchronize. Unless you mark the favorite link as a mobile favorite, only the link will be downloaded to your Pocket PC, and you will need to connect to your ISP or network to view the content. For more information on synchronization, see ActiveSync Help on the desktop computer.

Synchronize Mobile Favorites
If you are using Microsoft Internet Explorer 5.0 or later on your desktop computer, you can download mobile favorites to your Pocket PC. Synchronizing mobile favorites downloads Web content to your Pocket PC so that you can view pages while you are disconnected from your ISP and desktop computer. Use the Internet Explorer plug-in installed with ActiveSync to create mobile favorites quickly.

Create a Mobile Favorite

1. In Internet Explorer on your desktop computer, click Tools and then Create Mobile Favorite. 2. To change the link name, enter a new name in the Name box. 3. Optionally, in Update, select a desired update schedule. 4. Click OK. Internet Explorer downloads the latest version of the page to your desktop computer. Companion Programs 10-27
5. Synchronize your Pocket PC and desktop computer. Mobile favorites that are stored in the Mobile Favorites folder in Internet Explorer are downloaded to your Pocket PC.
If you did not specify an update schedule in step 3, you will need to manually download content to keep the information updated on your desktop computer and Pocket PC. Before synchronizing with your Pocket PC, in Internet Explorer on your desktop computer, click Tools and then Synchronize. You will see the last time content was downloaded to the desktop computer, and you can manually download content if needed. You can add a button to the Internet Explorer toolbar for creating mobile favorites. In Internet Explorer on your desktop computer, click View, Toolbars, and then Customize.

Save Pocket PC Memory

Mobile favorites take up storage memory on your Pocket PC. To minimize the amount of memory used:
In the settings for the Favorites information type in ActiveSync options, turn off pictures and sounds, or stop some mobile favorites from being downloaded to the Pocket PC. For more information, see ActiveSync Help. Limit the number of downloaded linked pages. In Internet Explorer on the desktop computer, right-click the mobile favorite you want to change and then Properties. In the Download tab, specify 0 or 1 for the number of linked pages you want to download.
Maintaining the Pocket PC / Backup Utility
, Programs, Utilities, and then Backup Utility.

Backup Utility is used to back up or restore files saved in the Pocket PC. You can back up personal data such as Calendar, Contacts, Tasks, Personal profile, Network settings, etc.

Storage Space

When making backups, you can choose the following storage spaces: 1. My Documents: Data saved here may disappear when you perform a cold boot. It is recommended that you use this area only as temporary storage. 2. External storage card: Mini SD card
Maintaining the Pocket PC

Backup Files

Wizard Mode
Tap Backup. Tap Next Button and the
Wizard will guide through the steps that follow. Standard: Switch to the Standard mode.

Standard Mode

Backup your personal data to a storage space.

Tap the Backup tab.

Tap to check the items for backup. Tap the function button to select the storage space from the list. Tap Backup Button to start
the backup. Advanced Button: Enter the Advanced settings screen.
Advanced Settings Options
Under the Backup Files screen, tap Advanced settings screen as shown below. Advanced Button to enter the
Check the options as required.
If you check this option, the Wizard will guide you through the steps to complete the operation the next time you open Backup Utility. Cancel Button OK Button If you checked Auto backup files, tap to enter the screen

shown on the left.

Select the backup option. Select the site to backup to. Pocket PC performs auto backup when the battery power is low. To backup regularly, tap to
select Auto Backup on schedule.
If you checked Auto backup on schedule, tap to enter the
screen shown on the left.
Backup frequency. Tap the date button on the right of Starting to set the starting date. Tap the time button on the right of Starting to set the starting time. If you have selected Weekly, tap the function button on the right of Every to set the day of the week to backup. If you selected Manage old backup files, tap to enter the
Tap the arrowhead to set the number of files. Tap the files to be retained.

Restore Files

Caution! 1. When restoring files, the system will delete all current data in the Pocket PC and replace it with the backup files. 2. To make sure that files can be restored successfully, do not use the Pocket PC while performing restore. 3. Restore cannot be stopped once it is started. Think carefully before proceeding. 4. After restore completed, your Pocket PC will reboot.
Tap Restore. Tap Next Button and the
Restore the backup personal data from a storage space.

Tap the Restore tab.

Select Latest below Restore From. Or select from the list. Tap backup file name from the list under File Name. Tap restoring. Restore Button to start

In addition, you can use the Rename/Move or Save As function provided by the program above to move or save files to the storage card.
Tap , Settings, the System tab, and then System Information.
Tap + or - to display or hide the system information.

Voice Commander /

, Programs and then Voice Commander.
Voice Commander is continuous voice recognition application software in the Pocket PC. Voice Commander allows the user to use their own voice to dial and control functions. Voice Commander has the following features: Fully voice-controlled system that allows the user to complete operations (such as dialing phone or running applications) quickly without using hands. Uses Speaker-Independent (SI) recognition technology that allows the user to use the Pocket PC immediately without having to train or pre-record for the system. Provides a Conversational UI for guiding beginners to issue voice commands through the conversational method. The user can then use commands easily without any practice. Provides the Voice tag and digit model adaptation function so that the user can customize personal settings and further increase recognition and convenience in usage. The Voice Commander provided with this product does not need personal training or recording. You can use voice control to operate this Pocket PC immediately. Try calling out Solitaire to play. Tap the Voice Commander Button on the side of the Pocket PC and when the system prompts you to Say Command, just say Start Solitaire and the Solitaire game screen will appear. Voice Commander 12-1

Starting Voice Commander

Here are two methods for running Voice Commander: 1. Tap
, Programs, Voice Commander, and then Voice Commander. button on the Pocket
2. Voice Commander Button. The system sets the
PC as the exclusive Voice Commander button. Just press this button to run Voice Commander. Show the format of voice command. Re-Start Button: Restart Voice Commander. Menu Button: Settings: Setup Voice Commander. Help: About Voice Commander. Exit: Exit Voice Commander.

, Settings, the

Personal tab, and then Buttons to redefine the Voice Commander hot
key or other hardware buttons.

Voice Command Format

Press the Voice Commander Button on the Pocket PC and enter the Voice Commander screen.
Voice Name dialing Usage: Call <Contact> at <Home/Work/Mobile> Example 1: Call Jennifer Lopez Example 2: Call Jennifer Lopez at mobile Voice Show Contact Usage: Show <Contact> at <Home/Work/Mobile> Example 1: Show Eric Clapton Example 2: Show Eric Clapton at work Voice Digit Dial Usage: Digit Dial Example: Digit Dial (System: What number) 29109088 Voice Show Appointment Usage: Todays/Tomorrows/ This weeks Appointment Voice Play Music File Usage: Play <Music file name> Example 1: Play The Moment Example 2: Play SHE album Example 3: Play Music Goodbye Usage: Goodbye Start Application Usage: Start <Application> Example: Start Calendar

Tips All the names in Contacts will automatically become recognizable contacts in the Voice dialing syntax. However, if the number of contacts exceeds 1000 entries, the system will not recognize the excessive entries. To add these entries to Voice Commander for recognition, tap Menu and then Settings or run Voice Commander Settings to check and add these contacts manually for voice recognition. If your volume is too low or if your surroundings are so noisy that the system cannot recognize your voice, the system will prompt you Please say again. Adjust the distance between yourself and your Pocket PC or reduce the noise and try again.
Tips If the user has a heavy accent that may cause poor voice recognition, use any of the following methods to train the personal digital adapted model in order to increase recognition: 1. Tap Menu, Setting, and then the Digit Training tab. 2. Tap Voice Commander Settings and then the Digit Training tab. Tips You can also tap Voice Commander, Menu, and then Exit to end Voice Commander. If you open another program while using Voice Commander and it covers the Voice Commander screen, Voice Commander will terminate automatically.

Voice Commander Settings

There are two ways to run Voice Commander Settings: Tap Settings. Tap Menu and then Settings while using Voice Commander. Voice Commander Settings allows the user to personalize the Voice Commander settings, add and remove contacts or applications within the recognition range, record voice tags or play commands to prompt the user on how to say the correct command. , Programs, Voice Commander, and then Voice Commander

Contacts Settings Page

Tap Voice Commander Settings and then the Contacts tab. The setting page will list all the names and their status (whether or not it is selected, with or without voice tag) in Contacts. Check box function If a contact is checked, it can be identified normally. If unchecked, this indicates that it is not within the recognizable range. Please create a voice tag. Lips icon: Voice tag is built. Tap a contact name to highlight it for using with buttons.
Play Button: Play the recorded voice tag for this contact and hear how it is pronounced. Build Button: Record the voice tag for this contact again. Delete Button: Delete the voice tag for this contact. Contacts tab: Sets the voice commands for Contacts. Application tab: Sets the voice commands for applications. Digit Training tab: Sets the voice command for digital dialing. Advanced Settings tab: Sets the length and sensitivity for digital dialing.
For example, record Alex Cooper in Contacts as Sweet Heart. 1. Tap Alex Cooper. 2. Tap Build Button. 3. When you hear a beep, say the words Sweet Heart that you want to record. 4. When you hear a second beep, say Sweet Heart again. 5. After recording twice, the system will play the voice you just recorded to indicate that you have created a voice tag. 6. At this time, a Lips icon appears to the right of your contact, Alex