Pub. 988-0143-661 www.eaglesonar.com
Fish-finding & Depth Sounding Sonars
FishMark 320 and SeaFinder 320DF
Installation and Operation Instructions
Copyright 2002 Eagle Electronics All rights reserved. Eagle is a registered trademark of Eagle Electronics Marine-Tex is a trademark of Illinois Tool Works Inc.
Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. On the cover: SeaFinder 320DF shown. Other models covered in the manual are similar.
For free owner's manuals and other information, visit our web site:

www.eaglesonar.com

Eagle Electronics P.O. Box 669 Catoosa, OK USA 74015 Printed in USA.

Table of Contents

Section 1: Read Me First!.. 1 Capabilities and Specifications:... 2 How To Use This Manual: Typographical Conventions. 4 Section 2: Installation & Accessories. 7 Transducer Installation... 7 Recommended Tools and Supplies.. 8 Selecting a Transducer Location... 8 Transom Transducer Assembly and Mounting. 11 Trolling Motor Bracket Installation (Single-Frequency only)17 Shoot-Thru-Hull Preparation and Installation. 19 Speed/Temperature Sensors.. 21 Power Connections... 24 Mounting the Unit: Bracket, In-Dash or Portable.. 26 Bracket Installation... 26 In-Dash Installation... 28 Portable Installation... 29 Section 3: Basic Sonar Operation.. 31 Keyboard... 31 Power/Lights (On and Off).. 32 Menus... 33 Main Menu... 33 Sonar Menu.... 35 Pages... 36 Basic Sonar Quick Reference.. 39 Sonar Operations.. 40 Fish Symbols vs. Full Sonar Chart.. 43 Other Free Training Aids.. 43 Section 4: Sonar Options & Other Features.. 45 ASP (Advanced Signal Processing)... 45 Alarms.... 46 Calibrate Speed... 49 Chart Speed... 49 Depth Cursor... 50 i
Depth Range - Automatic... 51 Depth Range - Manual... 51 FasTrack.... 52 Fish I.D. (Fish Symbols & Depths)... 52 FishTrack... 55 FishReveal... 55 Frequency (Change Trans Frequency Seafinder 320DF only) 57 Grayline... 58 HyperScroll... 60 Noise Rejection... 60 Overlay Data... 60 Ping Speed & HyperScroll.. 62 Pop-Up Help... 64 Reset Options... 64 Reset Water Distance... 65 Screen Contrast and Brightness.. 65 Sensitivity & Auto Sensitivity.. 65 Set Keel Offset... 67 Set Language... 69 Software Version Information.. 69 Sonar Color Mode.. 70 Sonar Chart Display Options... 70 Full Sonar Chart... 70 Split Zoom Sonar Chart... 71 Split Frequency Sonar Chart (Seafinder 320df only). 72 Digital Data/Chart... 73 Sonar Simulator... 74 Stop Chart... 74 Surface Clarity... 75 Units of Measure... 76 Zoom, Zoom Bar & Zoom Pan... 76 Section 5: Troubleshooting... 79 Section 6: Supplemental Material.. 85 ii
How this manual can get you out on the water, fast!
Welcome to the exciting world of digital sonar! We know you're anxious to begin finding fish, but we have a favor to ask. Before you grab your unit and begin installing it, please give us a moment or two to explain how our manual can help you get the best performance from your compact, wide-screen, fish finder. First, we want to thank you for buying an Eagle sonar. Whether you're a first time user or a professional fisherman, you'll discover that your unit is easy to use, yet capable of handling demanding sonar tasks. You won't find another sonar unit with this much power and this many features for this price! Our goal for this book is to get you on the water fast, with a minimum of fuss. Like you, we'd rather spend more time boating or fishing and less time reading the manual! So, we designed our book so that you don't have to read the whole thing from front to back for the information you want. At the start (or end) of each segment, we'll tell you what content is coming up next. If it's a concept you're already familiar with, we'll show you how and where to skip ahead for the next important topic. We've also made it easy to look up any tips you may need from time to time. Here's how: The manual is organized into 6 sections. This first section is an introduction to the sonar unit. It tells you the basics you need to know before you can make the unit look below the surface to find some fish. Section 2 will help you install your unit and the transducer. We'll also tell you about some of the available accessories. Section 3 covers Basic Sonar Operation. It will show you how easy it is to run your sonar, right out of the box. This section features a one-page Sonar Quick Reference. (If you've already jumped ahead and figured out how to install the unit yourself, and you just can't wait any longer, turn to the Quick Reference on page 39 and head for the water with your sonar unit!) 1

NOTICE! The storage temperature range for your unit is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Celsius). Extended storage in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty. For more information, contact the factory's Customer Service Department; phone numbers are listed on the last page.

How Sonar Works

Sonar has been around since the 1940s, so if you already know how it works, skip ahead to the next segment on the typographical conventions used in this manual. But, if you've never owned a sonar fish finder, this segment will tell you the under water basics. Sonar is an abbreviation for SOund NAvigation and Ranging, a technology developed during World War II for tracking enemy submarines. A sonar consists of a transmitter, transducer, receiver and display. In simple terms, here's how it finds the bottom, or the fish: The transmitter emits an electrical impulse, which the transducer converts into a sound wave and sends into the water. (The sound frequency can't be heard by humans or fish.) The sound wave strikes an object (fish, structure, bottom) and bounces back to the transducer, which converts the sound back into an electrical signal. The receiver amplifies this return signal, or echo, and sends it to the display, where an image of the object appears on the scrolling sonar chart. The sonar's microprocessor calculates the time lapse between the transmitted signal and echo return to determine the distance to the object. The whole process repeats itself several times each second.
How to use this manual: typographical conventions
Many instructions are listed as numbered steps. The keypad and arrow "keystrokes" appear as boldface type. So, if you're in a real hurry (or just need a reminder), you can skim the instructions and pick out what menu command to use by finding the boldface command text. The fol4
lowing paragraphs explain how to interpret the text formatting for those commands and other instructions: Arrow Keys The arrow keys control a horizontal line depth cursor on the sonar screen. The arrow keys also help you move around the menus so you can execute different commands. They are represented by symbols like these, which denote the down arrow key, the up arrow, the left arrow and the right arrow: . Keyboard The other keys perform a variety of functions. When the text refers to a key to press, the key is shown in bold, sans serif type. For example, the "Enter/Icons" key is shown as ENT and the "Menu" key is shown as MENU. Menu Commands A menu command or a menu option will appear in small capital letters, in a bold sans serif type like this: DEPTH CURSOR. These indicate that you are to select this command or option from a menu or take an action of some kind with the menu item. Text that you may need to enter or file names you need to select are show in italic type, such as data type. Instructions = Menu Sequences Most functions you perform with the sonar unit are described as a sequence of key strokes and selecting menu commands. We've written them in a condensed manner for quick and easy reading. For example, instructions for turning on the Fish ID feature would look like this: 1. From the Sonar Page, press MENU| to SONAR FEATURES|ENT. 2. Press or to FISH ID SYMBOLS|ENT|EXIT|EXIT. Translated into complete English, step 1 above would mean: "Start on the Sonar Page. Press the Menu key then repeatedly press (or press and hold) the down arrow key to scroll down the menu and select (highlight) 5

the unit is not in use. When the unit is turned off but still connected to a power supply, electrolysis can occur in the power cable plug. This may result in corrosion of the plug body along with the electrical contacts in the cable and the unit's power socket. In saltwater environments we recommend you connect the power cable to the auxiliary power switch included in most boat designs. If that results in electrical interference, or if such a switch is not available, we recommend connecting direct to the battery and installing an inline switch. This will let you shut off power to the power cable when the unit is not in use. When you are not using the unit, you should always shut off power to the power cable, especially when the power cable is disconnected from the unit. If possible, keep the power cable away from other boat wiring, especially the engine's wires. This will provide the best isolation from electrical noise. If the cable is not long enough, splice #18 gauge wire onto it. The power cable has two wires, red and black. Red is the positive lead, black is negative or ground. Make sure to attach the in-line fuse holder to the red lead as close to the power source as possible. For example, if you have to extend the power cable to the battery or power buss, attach one end of the fuse holder directly to the battery or power buss. This will protect both the unit and the power cable in the event of a short. It uses a 3-amp fuse.
To unit Black wire 12 volt battery Optional power off switch for saltwater installations

Red wire with 3 amp fuse

Power connections for the sonar unit.
CAUTION: Do not use this product without a 3-amp fuse wired into the power cable! Failure to use a 3-amp fuse will void your warranty. This unit has reverse polarity protection. No damage will occur if the power wires are reversed. However, the unit will not work until the wires are attached correctly. An optional 8-foot, CA-4 external power cable with a cigarette lighter adapter is available from Eagle.

Sonar unit rear view

Power/transducer socket Power cable Transducer cable

Accessory socket

Accessory cable
Sonar unit cable connections.
Mounting the Unit: Bracket, In-Dash or Portable
You can install the sonar unit on the top of a dash with the supplied gimbal bracket. It can also be installed in the dash or mounted on a portable power supply. If you use the supplied bracket, you may be interested in the optional R-A-M bracket mounting system. This converts the unit's gimbal bracket to a swivel mount, which can be used on the dash or overhead mounting positions. Installation instructions are supplied with the R-A-M mounting kits. Bracket Installation Mount the unit in any convenient location, provided there is clearance behind the unit when it's tilted for the best viewing angle. You should 26

also make sure there is enough room behind the unit to attach the power and transducer cables. (A drawing on the next page shows the dimensions of a gimbal-mounted sonar unit.) Holes in the bracket's base allow wood screw or through-bolt mounting. You may need to place a piece of plywood on the back side of thin fiberglass panels to reinforce the panel and secure the mounting hardware.
Front Install the gimbal bracket. Orient the bracket so the arms slope toward the front of your unit.
Drill a 1-inch (25.4 mm) hole in the dash for the power and transducer cables. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in position and results in a neat installation. Some customers, however, prefer to mount the bracket to the side of the cable hole it's a matter of personal preference. After drilling the hole, pass the transducer connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top. If you wish, you can fill in the hole around the cables with a good marine caulking compound. (Some marine dealers stock cable hole covers to conceal the opening.) No matter what type of installation you prefer, be sure to leave enough slack in the cables to allow tilting or swiveling 27
the unit. If you choose to fill in the hole, be sure to position the cables against the rear edge of the hole as you apply the fill material.
72.9 [2.87] 173.9 [6.85] 23.4 [0.92]

137.9 [5.43]

157.9 [6.22]
56.9 Millimeter [2.24] [Inch] Front view (left) and side view (right) showing dimensions of the sonar unit when mounted on gimbal bracket.
Before positioning the bracket, be sure to hold the cables against the rear edge of the hole. Then, slide the bracket over the hole and butt the rear of the bracket base firmly against the cables, thus pinning them in place against the side of the hole. Finally, fasten the bracket to the dash. Attach the unit to the gimbal bracket using the supplied gimbal knobs and washers. In-Dash Installation You can mount the unit in the dash with an optional FM-5 In-Dash Adapter Kit. The kit includes mounting hardware, a template for cutting the hole and an instruction sheet, part 988-0147-43. 28

Power/lights on and off

To turn on the unit, press PWR. To change the backlight, press PWR again. This unit has two backlight levels to select from. Repeatedly pressing PWR will cycle through the backlight settings, turn off the backlight, then turn it back on again. Turn off the unit by pressing and holding the PWR key for about 3 seconds. 32
Your sonar unit will work fine right out of the box with the factory default settings. You only need to learn a few basic functions to enhance your viewing. We'll discuss them briefly here, then talk about them and all the other commands in more detail in the next section, which begins on page 45. Your unit has three primary menus that control its operation. They are the Main Menu, the Sonar Menu and the Pages Menu. Main Menu The Main Menu contains some basic function commands and some setup option commands. You access the Main Menu by pressing MENU|MENU. You run a command by using the or to highlight the command and then pressing ENT. To clear the Main Menu screen and return to the Page display, press EXIT. (Remember, our text style for "MENU|MENU" means "press the Menu key twice." See a full explanation of our instruction text formatting on page 4, Instructions = Menu Sequences.)

Main Menu.

Main Menu Commands
There are four "basic" Main Menu commands that you'll really want to read more about. They are: Screen command: changes the contrast or brightness of the display screen. Use this command to adjust how the screen looks under various lighting conditions. Sounds command: enables or disables the sounds for key strokes and alarms, controls the volume and sets the alarm style. If you don't like to hear a beep each time you press a key, you can turn this off, or select tunes or sound effects instead. The sounds are especially useful when used with the Fish I.D. fish symbol feature and fish alarm feature. Sonar Alarms command: turns alarms on or off and changes alarm thresholds. The fish alarm, used with Fish I.D., is the most popular use. It tells you when the sonar sees a fish. You can also set deep or shallow depth alarms and zone alarms. Popup Help command: turns the pop-up help boxes on or off. When you select a menu command, these information boxes appear to tell you what the command does or how to use the command. The default setting is on, which is really handy while you're learning. The remaining Main Menu commands are for more advanced functions, mostly setting various sonar options. (They're all detailed in Sec. 4.) Units of Measure command: selects the units of measure used for showing speed/distance, depth and temperature. Set Keel Offset command: calibrates the unit to show depth under the keel or actual depth from the surface. Calibrate Water Speed command: adjusts how a speed sensor measures water speed. Reset Water Distance command: resets water distance log to zero. Sonar Simulator command: turns the simulator feature on and off. Useful for learning how to operate the unit and all its functions. 34

9. If you are drifting at a very low speed or anchored, you are not moving fast enough for a fish to return the tell-tale fish arch signal. As you drift over a fish, or as a fish swims through the transducer's signal cone, the fish echo will appear as a straight line suspended between the surface and the bottom. 10. To turn off the unit, press and hold PWR key for three seconds.

Sonar Operations

As you can see from the quick reference, basic operation is pretty easy, right out of the box. If you are a sonar novice, try operating the unit with the factory defaults until you get a feel for how it's working. As you're learning the basics, there is one setting you might want to tinker with from time to time Sensitivity. Sensitivity controls the unit's ability to pick up echoes. If you want to see more detail, try increasing the sensitivity, a little at a time. There are situations when too much clutter appears on the screen. Decreasing the sensitivity can reduce the clutter and show the strongest fish echoes, if fish are present. As you change the sensitivity setting, you can see the difference on the chart as it scrolls. You can change the sensitivity level whether you are in Auto Sensitivity mode or Manual Sensitivity mode. The adjustment method works the same in both modes, but it gives you slightly different results. Adjusting sensitivity in Auto Sensitivity Mode is similar to manually adjusting a car's speed with the accelerator pedal while cruise control is on. You can tell the car to run faster, but when you let off the gas the cruise control automatically keeps you from running slower than the minimum speed setting. In the sonar unit, auto mode will let you increase sensitivity to 100 percent, but the unit will limit your minimum setting. This prevents you from turning sensitivity down too low to allow automatic bottom tracking. When you change the setting with auto turned on, the unit will continue to track the bottom and make minor adjustments to the sensitivity level, with a bias toward the setting you selected. 40
Adjusting sensitivity in Manual Sensitivity Mode is similar to driving a car without cruise control you have complete manual control of the car's speed. In the sonar unit, manual mode allows you to set sensitivity at 100 percent (maximum) or zero percent (minimum.) Depending on water conditions, the bottom signal may completely disappear from the screen when you reduce sensitivity to about 50 percent or less!

To switch to a different depth setting, open the Sonar Alarms menu and repeat the instructions in steps 3 and 4 above. Fish Alarm Use the fish alarm for a distinctive audible alarm when fish or other suspended objects are detected by the Fish I.D. feature (Fish I.D. must be turned on for the Fish Alarm to work). A different tone sounds for each fish symbol size shown on the display.
To turn the fish alarm on: 1. Press ALARM.
2. Press to FISH ALARM|ENT|EXIT. 3. To turn off the alarm, press ALARM| to FISH ALARM|ENT|EXIT.

Brightness

See the entry in this section for Screen Contrast and Brightness.

Calibrate Speed

The speed sensor can be calibrated to compensate for inaccuracies. Before you change the setting, first calculate the percentage that the speed is off. You will enter this percentage in a moment. For example, if you figure the sensor is reading 10 percent faster than actual speed, you will enter 10 in the calibration window. If the sensor is reading 5 percent slower than true speed, you will enter + 5 in the window. Perform your test in relatively calm water free of current, if possible. (Unless, of course, you are taking the current speed into consideration when making your calculation.) After you have a correction figure, here's how to enter it: 1. Press MENU|MENU| to CALIBRATE WATER SPEED|ENT. 2. Enter the number you calculated earlier: press or to change the first character (+ or ), then press to move the cursor to the next number and repeat until the percentage is correct, then press EXIT.

Chart Speed

The rate that echoes scroll across the screen is called the chart speed. The default is maximum; we recommend that you leave the speed set there for virtually all fishing conditions. However, you might consider experimenting with chart speed when you are stationary or drifting very slowly. You may sometimes achieve better images as you slow down the chart speed to match how fast you are moving across the bottom. If you are at anchor, ice fishing or fishing from a dock, experiment with a chart speed around 50 percent. If you are drifting slowly, try a chart speed around 75 percent. When you are stationary and a fish swims through the sonar signal cone, the image appears on the screen as a long line instead of a fish arch. Reducing the chart speed may result in a shorter line that more closely resembles a regular fish return. 49
If you do experiment with chart speed, remember to reset it to maximum when you resume trolling or moving across the water at higher speed. To change chart speed: 1. From the Sonar Page, press MENU| to CHART SPEED|ENT. 2. The Chart Speed Control Bar appears. Press to decrease chart speed; press to increase chart speed. 3. When it's set at the desired level, press EXIT.

Contrast

Depth Cursor
The depth cursor consists of a horizontal line with a digital depth box on the right side. The numbers inside the box show the depth of the cursor. Cursor line

Depth box

Sonar chart with the depth cursor active. The line indicates the large fish is 34.64 feet deep.
The cursor can be moved to any location on the screen, letting you pinpoint the depth of a target. 50
1. From the Sonar Page, press MENU| to DEPTH CURSOR|ENT. 2. The depth cursor appears. Press to lower the cursor line; press to raise the cursor line. 3. To clear the depth cursor, press EXIT.

Depth Range - Automatic

When turned on for the first time, the bottom signal is automatically placed in the lower half of the screen. This is called Auto Ranging and is part of the automatic function. However, depending upon the bottom depth and the current range, you can change the range to a different depth. To do this: 1. From the Sonar Page, press MENU| to DEPTH RANGE|ENT. 2. The Depth Range Control Scale appears. Press or to select a different depth range. A black bar highlights the selected range. Range numbers in gray cannot be selected. 3. When the new range is selected, press EXIT to clear the menu.

Depth Range - Manual

You have complete control over the range when the unit is in the manual mode. There are 16 depth ranges, from 5 feet to 4,000 feet.
To switch to Manual Depth Range:
1. First, turn off automatic depth range. From the Sonar Page, press MENU| to AUTO DEPTH RANGE|ENT. 2. Press to DEPTH RANGE|ENT and the Depth Range Control Scale appears. 3. Press or to select a different depth range. A horizontal black bar highlights the selected range. 4. When the new range is selected, press EXIT to clear the menu. 51
To turn Auto Depth Range on again: 1. From the Sonar Page, press MENU| to AUTO DEPTH RANGE|ENT|EXIT.
NOTE: The sonar's depth capability depends on the transducer installation, water and bottom conditions, and other factors.

FasTrack

This feature automatically converts all echoes to short horizontal lines on the display's far right side. The graph on the rest of the screen continues to operate normally. FasTrack gives you a rapid update of conditions directly under the boat. This makes it useful for ice fishing, or when you're fishing at anchor. When the boat is not moving, fish signals are long, drawn out lines on a normal chart display. FasTrack converts the graph to a vertical bar graph that, with practice, makes a useful addition to fishing at a stationary location.

FishTrack

The FishTrack feature shows the depth of a fish symbol when it appears on the display. This lets you accurately gauge the depth of targets. This feature is available only when the Fish I.D. feature is on. The default setting for FishTrack is off. To turn on FishTrack: (Note: These instructions will turn on FishTrack and Fish I.D. at the same time.) 1. From the Sonar Page, press MENU| to SONAR FEATURES|ENT. 2. Press to FISH ID DEPTHS|ENT|EXIT|EXIT. To turn off FishTrack, repeat the instructions in step 1. Turning off FishTrack in this manner will not turn off Fish I.D. symbols.
Symbols with FishTrack depths
Sonar Features menu with Fish I.D. Depths selected (at left, dualfrequency menu; center, single-frequency menu). When the check box to the left is checked, the feature is on. At right, Sonar Page showing Fish I.D. symbols and FishTrack depths turned on.

FishReveal

When displaying actual sonar returns, the FishReveal feature uses 10 levels of gray tones to show fish targets hidden by surface clutter, thermoclines, weed beds and other cover. 55
The normal mode of operation (with FishReveal turned off) shows the weakest echoes as black and the strongest echoes in light gray. Since all weak echoes are black, fish arches show boldly against the white background. The drawback is that all weak echoes such as thermoclines are also emphasized. This can make it hard to distinguish fish signals inside thermoclines or other cover. In FishReveal mode, the weakest echoes are white and the strongest echoes are black. Echoes in between vary in gray in proportion to their signal strength. The Grayline control determines the range for black to white. Also note that when using FishReveal, we recommend that you turn off Auto Sensitivity and turn up Sensitivity to near maximum.
Sonar Color Mode command with FishReveal selected (at left, dual-frequency menu; at right, single-frequency menu).
To turn FishReveal on: 1. From the Sonar Page, press MENU| to SONAR FEATURES|ENT. 2. Press to SONAR COLOR MODE|ENT| to FISHREVEAL|ENT. 3. Press EXIT| to AUTO SENSITIVITY|ENT| to SENSITIVITY|ENT. 4. Press until the Sensitivity Control Bar reads 100% (or close to it), then press EXIT. (If you reach the maximum limit, a tone sounds.)

Set Language

This unit's menus are available in 10 languages: English, French, German, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU|MENU| to SET LANGUAGE|ENT. 2. Use or to select a different language and press ENT. All menus now appear in the language you selected.
Software Version Information
From time to time, Eagle updates the operating system software in some of its products. These software upgrades are usually offered to customers as free downloads from our web site, www.eaglesonar.com. These upgrades make the unit perform better or introduce a new feature or function. You can find out what software version is running in your sonar unit by using the Software Information command.
Software Information screen.
1. Press MENU|MENU| to SOFTWARE INFO|ENT. 2. Read the information displayed on the screen. 3. To return to the last page displayed, press EXIT|EXIT.

Sonar Color Mode

The default color scheme for the sonar chart is grayscale, but we offer other variations to suit your viewing preferences. You can select the chart to be displayed in reverse grayscale, bottom black or FishReveal mode. (For more information on FishReveal, see the entry on that topic elsewhere in this section.) To change the chart mode color scheme: 1. From the Sonar Page, press MENU| to SONAR FEATURES|ENT. 2. Press to SONAR COLOR MODE|ENT. 3. Press or to Mode Name|ENT. 4. Press EXIT|EXIT to return to the Sonar Page.
Sonar Chart Display Options
The Pages Menu offers four chart display options for dual-frequency models and three options for single-frequency models. To access them, press PAGES| to Option Name|EXIT.
Pages Menu showing sonar chart display options (at left, dual-frequency menu; at right, single-frequency menu).
Full Sonar Chart This is the default mode used when the unit is turned on for the first time or when it's reset to the factory defaults. The bottom signal scrolls across the screen from right to left. Depth scales on the right side of the screen aid in determining the depth of 70
targets. The line at the top of the screen represents the surface. The bottom depth and surface temperature (if equipped with a temperature sensor or a transducer with a temp sensor built in) show at the top left corner of the screen. The FasTrack display shows just to the right of the scale. This changes all echoes into short horizontal bars, replicating a flasher sonar. The zoom bar on the far right shows the area that's zoomed when the zoom is in use. (See the Zoom section for more information.)
Full Sonar Chart. The Overlay Data (depth and water temperature) are both set to the small text size.
Split Zoom Sonar Chart A split chart shows the underwater world from the surface to the bottom on the right side of the screen. The left side shows an enlarged version of the right side. The zoom range shows at the bottom left corner of the screen.

EAGLE ELECTRONICS PO BOX 669, CATOOSA, OK 74015 (800) 324-1354

How to Obtain Service

in the USA:
We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer service to determine if a return is necessary. Many times, customer service can resolve your problem over the phone without sending your product to the factory. To call us, use the following toll-free number:

800-324-1354

8 a.m. to 5 p.m. Central Standard Time, M-F
Eagle Electronics may find it necessary to change or end our shipping policies, regulations, and special offers at any time. We reserve the right to do so without notice.

in Canada:

If you're in Canada and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer service to determine if a return is necessary. Many times, customer service can resolve your problem over the phone without sending your product to the factory. To call us, use the following toll-free number:

800-661-3983

905-629-1614 (not toll-free)
8 a.m. to 5 p.m. Eastern Standard Time, M-F
outside Canada and the USA:
If you have technical, return or repair questions, contact the dealer in the country where you purchased your unit. To locate a dealer near you, visit our web site, www.eaglesonar.com and look for the Dealer Locator. 86
Accessory Ordering Information for all countries
To order Eagle accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items. To locate an Eagle dealer near you, visit our web site, www.eaglesonar.com and look for the Dealer Locator. Or, you can consult your telephone directory for listings. 2) U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129 Call 1-800-324-0045 or visit our web site www.lei-extras.com. 3) Canadian customers can write: Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario L4W2R7 or fax 905-629-3118.

Shipping Information

If it becomes necessary to send a product for repair or replacement, you must first receive a return authorization number from Customer Service. Products shipped without a return authorization will not be accepted. When shipping, we recommend you do the following: 1. Always use the original shipping container and filler material the product was packed in. 2. Always insure the parcel against damage or loss during shipment. Eagle does not assume responsibility for goods lost or damaged in transit. 3. For proper testing, include a brief note with the product describing the problem. Be sure to include your name, return shipping address and a daytime telephone number.

Visit our web site:

Eagle Pub. 988-0143-661 Printed in USA 101702
Copyright 2002 All Rights Reserved Eagle Electronics