For example, if you have to extend the power cable to the battery or power buss, attach one end of the fuse holder directly to the battery or power buss. This will protect both the unit and the power cable in the event of a short. It uses a 3-amp fuse.
To unit Optional power off switch for saltwater installations
Black wire 12 volt battery

Red wire with 3 amp fuse

Power connections for the IntelliMap 480 GPS unit.
CAUTION: Do not use this product without a 3-amp fuse wired into the power cable! Failure to use a 3-amp fuse will void your warranty. This unit has reverse polarity protection. No damage will occur if the power wires are reversed. However, the unit will not work until the wires are attached correctly. An optional 8-foot, CA-4 external power cable with a cigarette lighter adapter is available from Eagle.
NMEA/DGPS Cable Connections
NMEA is a standard communications format for marine electronic equipment. For example, an autopilot can connect to the NMEA interface on the IntelliMap 480 and receive positioning information. The IntelliMap 480 can exchange information with any device that transmits or receives NMEA 0183 data. DGPS is an acronym for the Differential Global Positioning System. DGPS supplements and boosts the accuracy of basic GPS. DGPS was developed by the U.S. Coast Guard, which is responsible for the system's operation in the United States. Since it's creation, DGPS has become the international maritime standard for marine navigation. The most popular DGPS system relies on a grid of ground-based transmitters that send correction signals to DGPS receivers. These in turn, connect to the GPS receiver (such as the IntelliMap 480). Eagle offers an optional DGPS receiver for your unit. See the diagrams on the following page for general wiring connections. Read your other products owners manual for more wiring information. 13
NMEA/DGPS Wiring To exchange NMEA or DGPS data, the IntelliMap 480 has one NMEA 0183 version 2.0 communication port. Com port one (Com-1) can be used to receive NMEA format GPS data or DGPS data. The com port can also transmit NMEA format GPS data to another device. The three wires for the com port are combined with the two power wires to form the power/data cable. Com-1 uses the yellow wire to transmit, the orange wire to receive and the shield wire for signal ground.
Yellow (Transmit) Com-1 to IntelliMap 480 Orange (Receive) Shield (Ground) Receive Transmit Ground To DGPS Receiver
Com-1 wiring to receive DGPS position information from a DGPS receiver. Orange (Receive) Com-1 to IntelliMap 480 Shield (Ground) NMEA Transmit Ground To Other GPS Receiver

Navigation Page, going to a waypoint while creating a new trail.
The cross track error range is shown on the compass rose as a wide, white, corridor enclosing the course line. The outer edges of this white corridor represent lines that show the current cross track error range. The default for the cross track error range is 0.20 miles. For example, if the present position symbol touches the right cross track error line, then you are 0.20 miles to the right of the desired course. You need to steer left to return to the desired course. You can use the ZIN or ZOUT keys to change the cross track error range. 27
a circular symbol depicting your destination (waypoint) appears on the screen as you approach the waypoint, as shown on the screen in the preceding figure. Travel Time is the time that it will take to reach your destination at your present closing speed. (You can also customize the time data box to show Arrival Time instead. Arrival Time is the local time it will be when you arrive at the destination, based upon your present closing speed and track.) In the preceding example figure, the driver is headed west (a 265 track) toward a waypoint 265 (bearing) away. The cross track error range (white corridor) is 0.20 miles either side of the course. The driver is headed toward trail waypoint 4, which is 0.3 miles away. The vehicle is right on course. Traveling at a speed of 8 mph, the driver will arrive at the waypoint in 2 minutes, 17 seconds. The Navigation Page has its own menu, which is used for some advanced functions and for setting various options. (Options and setup are discussed in Sec. 5). To access the Navigation Page Menu, from the Navigation Page, press MENU. Map Page The Map Page screens show your course and track from a "bird's-eye" view. By default, this unit shows the map with north always at the top of the screen. (This can be changed. See the topic Map Orientation, in Sec. 5.) If you're navigating to a waypoint, the map also shows your starting location, present position, course line and destination. You don't have to navigate to a waypoint, however, to use the map. Map Page is the default screen that appears when you turn on the unit. To get to the Map Page from another page: Press PAGES| or to MAP|EXIT. When the Map Page is displayed, a screen similar to the following figures appears. The arrow in the center of the screen is your present position. It points in the direction you're traveling. The solid line extending from the back of the arrow is your plot trail, or path you've taken. The map zoom range is the distance across the screen. This number shows in the lower right corner of the screen. In the first of the following example figures, the range is 4,000 miles from the left edge of the map to the right edge of the map. The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its coverage area and the amount of mapping detail shown. There are 39 available map zoom ranges, from 0.02 miles to 4,000 miles. 28

Map screen showing Finding Waypoint, the result of a restaurant search.
7. To clear the search and return to the last page displayed, press EXIT|EXIT|EXIT|EXIT. (Before you completely exited out of the Search menus, you could have gone looking for another place.) NOTE: Search works from mapping and POI data loaded in the unit. If you do not have a high-detailed custom map (containing POI data) for the area you are searching loaded on the MMC, you may not find anything.

Set a Waypoint

a waypoint is simply an electronic "address," based on the latitude and longitude of a position on the earth. a waypoint represents a location, spot, or destination that can be stored in memory, then be recalled and used later on for navigation purposes. You can create a waypoint at the cursor position on the map, or at your current position while you are navigating. You can create a waypoint at any location by manually entering the position's latitude and longitude. You can copy waypoints from your unit to your personal computer with MapCreate software. When you want to repeat a trip, these archived waypoints can be reloaded into your GPS unit. To create and save a Waypoint: These first two techniques use the Quick Save method, the fastest and easiest way to create a waypoint. 37
Create Waypoint at Current Position While you are traveling, press WPT|WPT. The waypoint is saved and
automatically given a name with a sequential number, such as "waypoint 003." The waypoint symbol and number appear on the map.

Step 1. Step 2.

Step 3.

Step 4.

Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: vehicle continues on its way; number waypoint symbol is visible on map.
NOTE: The Quick Save method uses the default waypoint symbol until you edit an existing waypoint and change its symbol. (Edit Waypoint Symbol is described in Sec. 4.) After you have changed a waypoint symbol, the unit will remember the one you chose and use it the next time you "quick save" a waypoint. To revert back to the default symbol, edit a waypoint and choose the original symbol, or use the Reset Options command (described in Sec. 5). 38

Create Waypoint on Map

1. Use the arrow keys to move the cursor to the place where you want to make a waypoint. 2. Press WPT|WPT. The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001." The waypoint symbol and number appear on the map.

From left to right, these figures show the menu sequence for naming and saving a GPS Data File from the unit's memory to an MMC.
4. Loading to unit memory: There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selection box, use or to highlight the file, then press ENT to accept the selection. Next, press to LOAD DATA|ENT. The unit will display a completion message when the data transfer is finished. To return to the Page view, press EXIT|EXIT|EXIT|EXIT.
These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory.

Cancel Navigation

You can turn off any of the navigation commands after you reach your destination or at any other time by using the Cancel Navigation command. Press MENU|MENU| to CANCEL NAVIGATION|ENT| to YES|ENT.
Section 4: Advanced GPS Operations
Find Distance From Current Position To Another Location
1. While on the Map Page press: MENU| to FIND DISTANCE|ENT. 2. Center your cursor over the position you want to find the distance to. a rubber band line appears, connecting your current position to the cursor's location. The distance along that line will appear in a pop-up box. The box also shows the bearing to the point you're measuring to. 3. Press EXIT to return to regular operation.
At left, the distance from Dallas to Little Rock is 292.2 miles. At right, the distance from the boat's current position to the boat ramp is 0.52 miles.
Find Distance From Point to Point
You can also measure distance between two other points on the map. 1. While on the Map Page press: MENU| to FIND DISTANCE|ENT. 2. Center your cursor over the first position. (a rubber band line appears, connecting your current position to the cursor's location.) Press ENT to set the first point, and the rubber band line disappears. 3. Move the cursor to the second position. The rubber band line reappears, connecting the first point you set to the cursor. The distance along that line will appear in the pop-up box. 4. Press EXIT to clear the command and return to the page screen. (Press EXIT once more to clear the cursor.) 51

a route is a series of waypoints, linked together in an ordered sequence, that's used to mark a course of travel. You can visualize a route as a string of beads: The beads represent waypoints and the string represents the course of travel connecting waypoint to waypoint. The course from one waypoint to the next is a leg; routes are composed of one or more legs. The legs of all GPS routes are based on straight lines between waypoints. 53
a route provides the automatic capability to navigate through several waypoints without having to reprogram the unit after arriving at each waypoint. Once programmed into the GPS unit, a route provides the option of navigating forward through the route waypoints or in reverse order (you can even begin navigating in the middle of a route!) Create and Save a Route You have the option of creating and editing a route in the unit, or you can make a route on your computer with our MapCreate 6 software.

PC-created Routes

MapCreate is the easiest method for preparing a route, simply because your PC's larger screen, keyboard and mouse are easier to manipulate than the unit. To load a MapCreate route into the unit, follow instructions in MapCreate's manual for creating a route and saving it as part of a GPS Data File (file format *.usr). Copy the GPS Data File to an MMC and insert the MMC in the unit. (See Sec. 2 for instructions on installing MMCs. To load the GPS Data File into the unit's memory, see the entry on Transfer Custom Maps & GPS Data Files in Sec. 3, Basic GPS Operations.)
Routes Created in the Unit
You can create a route by selecting existing waypoints from the waypoint list or you can set a series of route waypoints on the map with cursor arrows and the Enter key. In this example, we'll create a route from the map. 1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE, press MENU|MENU| to ROUTE PLANNING|ENT|ENT.
Route Planning command on Main Menu, left, will open the Route List screen, right.
2. Press to (END OF ROUTE)|ENT| to ADD FROM MAP|ENT. The Map Page appears with the cursor showing.

Auto Satellite Search

To lock onto the satellites, the GPS receiver needs to know its current position, UTC time and date. (Elevation [altitude] is also used in the equation, but it's rarely required to determine a position.) It needs this data so that it can calculate which satellites should be in view. It then searches for only those satellites. When your GPS receiver is turned on for the first time, it doesn't know what your position or elevation (altitude) is. It does know the current UTC time and date since these were programmed into it at the factory and an internal clock keeps the time while the unit is turned off. (If the time and/or date are incorrect, you can set it using the "Set Local Time" menu.) The unit begins searching for the satellites using the above data that it acquired the last time it was turned on. This probably was at the factory. Since it's almost certain that you're not at our factory, it's probably looking for the wrong satellites. If it doesn't find the satellites it's looking for after approximately one minute, it switches to Auto Search. The receiver looks for any satellite in the sky. Due to advanced technology, the auto search time has shrunk significantly from the early days of GPS. Once the unit locks onto the satellites, it should take less than a minute to find your position the next time it's turned on, provided you haven't moved more than approximately 100 miles from the last location it was used. 66
GPS Auto Search on the Satellite Status Menu.
You can force the unit to immediately kick into auto search mode. Here's how: From the Satellite Status page, MENU| to GPS AUTO SEARCH|ENT| to YES|ENT.
Check MMC Files and Storage Space
To check MMC Files: Press MENU|MENU| to BROWSE MMC FILES|ENT.
Main Menu, left, MMC File Browser, right.
Communications Port Configuration
The unit has one NMEA 0183 version 2.0 compatible communication port, or com port for short. The Com Port Menu, which is accessed from the System Setup Menu, allows you to configure the communications port to send or receive data to another electronic device, such as an autopilot. The com port can be used for either NMEA, DGPS or SiRF Binary data transfer. 67
Menus for changing Com Port settings.
For connectors and wiring information for another device, see page 14. For assistance in configuring the unit to communicate with another device, consult the factory; customer service phone numbers are in the back of this manual. Also see the entries below for Configure DGPS and Configure NMEA. To set Com Port Configuration: 1. Press MENU|MENU| to SYSTEM SETUP|ENT. 2. Press to COMMUNICATIONS PORT|ENT.

Map Data

This menu lets you turn the map off, if desired (which turns the map screen into a GPS plotter); turn off or on the pop-up map info boxes; draw the map boundaries or boxes around the areas of high detail; or fill land areas with gray. You can also turn on or off Map Overlays, which display latitude and longitude grid lines or range rings on the map. This menu lets you select Navionics Maps; for instructions, see the Navionics Charts entry in this section. To get to Map Data: From the Map Page, press MENU| to MAP DATA|ENT.
Map Menu, left, Map Data Menu, right.
Show Map Data From the Map Page, press MENU| to MAP DATA|ENT. Press ENT to enter the EARTH MAP DETAIL selection list, and choose how much detail you want, from Off (so the unit operates like a GPS plotter) to High. After the option is set, press EXIT repeatedly to return to the page display. Pop-up Map Information From the Map Page, press MENU| to MAP DATA|ENT. Press to POPUP MAP INFORMATION. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display. Map Boundaries From the Map Page, press MENU| to MAP DATA|ENT. Press to DRAW MAP BOUNDARIES. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display. Fill Water With White From the Map Page, press MENU| to MAP DATA|ENT. Press to FILL WATER WITH WHITE. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display. Map Overlays (Range Rings; Lat/Long Grid) The map screen can be customized with four range rings and/or grids that divide the plotter into equal segments of latitude and longitude. Range rings are handy for visually estimating distances on the map. The ring diameters are based on the current zoom range. For example: at the 100 mile zoom, the screen will show two rings with your current position 76
in the center. The large ring touching the left and right sides of the screen is 100 miles in diameter (same as the zoom range). The second smaller ring is 50 miles in diameter (always 1/2 the zoom range). The distance from your current position to the smaller ring (the ring's radius) is 25 miles (always 1/4 the zoom range). With the arrow keys and map cursor, you can scroll the map to see the third and fourth rings. In this example, the distance to the third ring is 75 miles and distance to the fourth ring is 100 miles from your current position. To set range rings: From the Map Page, press MENU| to MAP DATA|ENT. Press to DRAW MAP BOUNDARIES| to RANGE RINGS. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display. To set Lat/Long Grid: From the Map Page, press MENU| to MAP DATA|ENT. Press to POPUP MAP INFORMATION| to LAT/LON GRID LINES. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display.

Map Menu, left; Map Orientation menu with the North Up map orientation option selected, right.
NOTE: In North Up and Course Up, the present position arrow appears in the center of the map page. In Track Up, the position arrow appears centered in the lower third of the page.

Navionics Charts

Your unit can display Navionics electronic charts on MMCs. They work just like a MapCreate custom map on an MMC.
Left, entrance to Chesapeake Bay in a MapCreate 6 custom map, 10 mile zoom. Center, same position on Navionics chart at 11.15 mile zoom and right, 5.56 mile zoom.
To display a Navionics chart: 1. Install the Navionics MMC in the memory card compartment and turn on the unit. (For full card install instructions, see Sec. 2.) WARNING: You should never format the MMC containing your Navionics chart. Formatting the MMC will permanently erase the chart from the card. 2. From the Map Page, press MENU| to MAP DATA|ENT| to NAVIONICS MAP CHOICE|ENT. Use or to select the Map Name, then press ENT|EXIT|EXIT.
These figures show menu sequence (from left to right) for selecting a Navionics chart for the South Chesapeake Bay area.
3. To turn off a Navionics chart, From the Map Page, press MENU| to MAP DATA|ENT| to NAVIONICS MAP CHOICE|ENT. Use or to select EAGLE, then press ENT|EXIT|EXIT. Port Information Navionics charts contain Port Services information, represented by anchor icons on the map display. An example is displayed in the following figure. To view Port Services information: 1. Use the arrow keys to move the cursor over a Port Services icon. When selected, a pop-up name box appears. 2. Press WPT to display the Port Services Information screen. The Port Services information screen has two windows. The top window lists the various service categories. The lower window lists the detailed services available in each basic category.
Port Services icons Pop-up name box

Cursor lines

Navionics chart showing Port Services icon selected by cursor.
3. To scroll through the Service Categories window: press ENT then use or to see the types of services available. As you highlight a different category, the list in the lower window changes. To return to the Map Page, press EXIT|EXIT. 4. Depending on the location, the Detailed Services window may have a long list of services under the General Services category. To scroll through the Detailed Services window: from SERVICE CATEGORIES, press to DETAILED SERVICES|ENT, then use or to read the list of available services. To return to the Map Page, press EXIT|EXIT. To return to the top service category window, press ENT|. 81
Port Services information screens.
Tidal Current Information Navionics charts contain Tidal Current information, represented at large zoom ranges by a box icon with the letter "C." The icon stands for a Tidal Current Station location. An example is displayed at right. When you zoom in to a sufficiently small zoom range, the icon itself becomes an animated arrow showing tidal current velocity and direction for the selected tidal station at the present time. At larger zoom ranges, you can select the boxed "C" icon and it becomes an animated arrow with a pop-up name box. An example is displayed in the following figure. To view Tidal Current information: 1. Use the arrow keys to move the cursor over a Tidal Current Station icon. When selected, a pop-up name box appears. 2. Press WPT to display the Tidal Current Information screen.

From time to time, Eagle updates the operating system software in some of its products. These software upgrades are usually offered to customers as free downloads from our web site, www.eaglesonar.com. These upgrades make the unit perform better or introduce a new feature or function. You can find out what software version is running in your unit by using the Software Information command. 89
System Setup command left; Software Information command, center. At right, the Software Information screen.
1. Press MENU|MENU| to SYSTEM SETUP|ENT| to SOFTWARE INFO|ENT. 2. Read the information displayed on the screen. 3. To return to the last page displayed, press EXIT|EXIT|EXIT.
Sounds and Alarm Sound Styles
Sounds triggered by key strokes and alarms can be adjusted: You first press MENU|MENU| to SOUNDS|ENT.
Sounds command, left. At right, the Sounds menu. Once in the Sounds menu:
To set Key Press Sounds: With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display. To set Alarm Sounds: Press to ALARM SOUNDS. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to return to the page display. To set Alarm Volume: Press to VOLUME. Press or to move the bar. The left end of the scale is low volume; the right end is high volume. After the option is set, press EXIT|EXIT to return to the page display. 90
To set Alarm Style: Press to ALARM STYLE|ENT. Press or to change the style, then press ENT. After the option is set, press EXIT|EXIT to return to the page display.

Track Smoothing

This is a factory setting on the GPS Setup menu that should always be left on. When stopped or traveling at slow speeds (such as walking or trolling), Track Smoothing prevents wandering of trails, the steering arrow, compass rose and a map in track-up mode.
Track Smoothing option, turned on.

Trail Options

There are several options you can use with trails. Some affect all trails, other options can be applied to a particular trail. You can change the way trails are updated, display or hide trails, make them flash on the screen or not flash, create a new trail, delete a trail, etc.

General Trail Options

To access the Trails Menu: 1. Press MENU|MENU| to MY TRAILS|ENT.
Main Menu, left, Trails Menu, center, Trail Options, right.
Delete All Trails To remove all of the trails from memory: from the Trails Menu, press to DELETE ALL|ENT| to YES|ENT. Flash Trails on Screen Option From the Trails Menu, press to TRAIL OPTIONS|ENT| to FLASH TRAILS. With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) Update Trail Option This menu lets you change the way the trail updates occur. WARNING: If you uncheck the Update Trail option, automatic trail creation and recording will be turned off. You must turn it back on to record trails. The default setting is on. From the Trails Menu, press to TRAIL OPTIONS|ENT. With UPDATE ACTIVE TRAIL highlighted, press ENT to check it (turn on) and uncheck it (turn off.)

Find Any Item Selected by Map Cursor
On the Map Page: with a POI or map feature selected by the cursor press WPT. To return to the previous page, press EXIT.
a POI selected by the cursor, left, POI information screen, right.
NOTE: Since the Go To Waypoint command is highlighted, you can navigate to the selected POI by pressing ENT|EXIT while in the POI Waypoint Information screen. 98
Find Interstate Highway Exits
1. From the Map Page, press MENU| to HIGHWAY EXITS|ENT, which calls up the Find Exit menu.
Find Highway Exits command, left, and Find Exit menu, right.
2. First, select a highway name by pressing ENT, which calls up the Find By Name menu. There are two highway search options: a. You can spell out the highway name in the top selection box. Press or to change the first letter, then press to move the cursor to the next letter and repeat until the name is correct, then press ENT|ENT. B. Jump down to the lower selection list by pressing ENT, then press or to select a highway from the list, then press ENT.

Find By Name menu.

3. Once you have selected a highway name you can then select an exit. Press to switch to the Exit List, then press or until you highlight the exit, then press ENT. 99
Find Exit menu, with an exit selected in the Exit List.
4. In the Exit Information screen you have two choices. a. Press ENT to navigate or "go to" the exit. B. Press |ENT to find the exit on the map.
"Go To Exit" option, left, "Find On Map" option, right.
You can also look up some additional information on the Exit Services located near this exit. Press to SERVICES|press or to select Service Name|ENT.
Exit Information screen, left; general location and amenities information, at right.
Find Map Places or Points of Interest (POI)
1. Press WPT, press or to select a map place or POI category, then press ENT. (To narrow your search, press then press or to select a subcategory before pressing ENT.) You will be given two options; Search By Name or By Nearest.
Find Waypoint menu with Lodging POI category selected, left, and with the RV Parks subcategory selected, right.
2. Search by nearest POI. Press |ENT. The "find by nearest" menu will show a "calculating" screen, then a list of the nearest POI's will appear. Press or to the selected POI and press ENT to call up the POI's Waypoint Information screen.
Find by Nearest option, left, Calculating screen, center, POI list, right.
3. Search by name of POI. Press ENT. There are two options: a. You can spell out the POI in the top selection box. Press or to change the first letter, then press to move the cursor to the next letter and repeat until the name is correct, then press ENT|ENT. B. Jump down to 101

Accessories, 1, 3, 4, 6, 11, 14, 15, 19, 30, 48, 95 Sec. 2, Installation & Accessories, 11 Alarm Clock, 61 Alarms, 23, 33, 46, 48, 59, 65, 66, 74 Anchor Alarm, 65, 66 Antenna, 1, 3, 4, 11, 12, 15, 16, 17, 33, 34, 113 Arrival Alarm, 33, 46, 48, 59, 65, 66, 74
Navigate, 53 Information Displays (Customize Display), 25 Installation, 4, 6, 11, 14, 15, 16, 17, 18, 48, 80 Sec. 2, Installation & Accessories, 11 Introduction GPS and WAAS, 6 Sec. 1, Introduction, 1 Specifications, 2 Typographical Conventions, 8
Backlights / Lighting, 2, 21 Batteries, 11, 12, 13, 17, 18 Brightness, 23, 87, 88
Keypad Description, 8, 21
Languages, 3, 88 Lat/Lon Grid (Map Data option), 77
Cancel Navigation, 23, 33, 41, 42, 46, 48, 50, 58 Communications Ports, 13, 14, 67, 68, 69 Compass, 7, 8, 26, 27, 33, 36, 40, 42, 46, 47, 53, 59, 74, 91 Contrast, 2, 23, 87, 88 Coordinate System, 69 Cursor, 34, 35, 39, 41, 42, 52, 53, 85 Custom Maps, 1, 3, 5, 18, 19, 29, 30, 35, 37, 48, 54, 80, 95 Customize Display, 25 Customize Map Data Shown, 75, 76, 77, 80, 81
Main Menu, 22, 23, 54, 58, 67, 91 Man Overboard, 40, 41 Map Boundaries (Map Data option), 76, 77 Map Data, 75, 76, 77, 80, 81 Map Datum, 70, 77, 78 Selection, 70, 77 Map Detail, 31, 76, 78 Map Fix (Coordinate System), 70, 71, 72 Map Menu, 76, 78, 79, 85 Map Orientation, 28, 78, 79 Map Overlays (Map Data option), 75, 76 Memory Cards (MMC), 1, 3, 4, 5, 18, 19, 20, 21, 23, 29, 33, 37, 44, 48, 49, 50, 54, 67, 80
Data Boxes (Customize Display), 25 Depth Range, 3, 4, 27, 28, 29, 30, 33, 34, 45, 75, 76, 77, 82, 83, 84, 85, 92
Navigating, 9, 33, 39, 40, 41, 42, 45, 46, 47, 53, 56, 58, 66 A Route, 58 A Trail, 45 Cancel, 23, 33, 41, 42, 46, 48, 50, 58 To Cursor Position, 41 To Icon, 53 Nearest, 35, 36, 39, 95, 101, 106, 107 NMEA, 13, 14, 67, 68, 69
GPS Data File, 5, 48, 49, 50, 54, 67
Icons, 3, 5, 8, 22, 29, 30, 31, 48, 52, 53, 78, 81, 82, 83, 84, 86 Creating, 52 Deleting, 52

Off Course Alarm, 65

Page Displays, 2, 24, 31, 32, 33, 73 Digital Data, 31 Map, 9, 21, 22, 24, 27, 28, 29, 31, 32, 33, 39, 40, 41, 42, 45, 46, 51, 53, 54, 55, 56, 57, 58, 59, 73, 74, 75, 76, 77, 78, 79, 80, 81, 95, 97, 98, 99, 102, 104, 106, 107, 108 Navigation, 21, 24, 26, 27, 28, 33, 40, 41, 42, 45, 46, 53, 54, 56, 57, 58, 59, 72 Satellite Status, 21, 24, 25, 26, 33, 72 POI (Point of Interest), 22, 23, 29, 30, 31, 35, 36, 37, 41, 42, 63, 73, 95, 98, 101, 102 POIs Search, 101 Pop-up Help, 85 Pop-up Map Info (Map Data option), 76 Power, 1, 2, 3, 6, 11, 12, 13, 14, 15, 16, 17, 18, 21, 22, 33 Product Specifications, 2

EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY
"We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family, or household use. We warrant this product against defects or malfunctions in materials and workmanship, and against failure to conform to this product's written specifications, all for one (1) year from the date of original purchase by you. WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship, or any non-conformity with the product's written specifications, occurred within one year from the date of your original purchase, which must be substantiated by a dated sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your original purchase date will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain without charge a replacement of the product or a refund for the product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT, MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty does NOT apply in the following circumstances: (1) when the product has been serviced or repaired by anyone other than us; (2) when the product has been connected, installed, combined, altered, adjusted, or handled in a manner other than according to the instructions furnished with the product; (3) when any serial number has been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owner's manual for the product. We reserve the right to make changes or improvements in our products from time to time without incurring the obligation to install such improvements or changes on equipment or items previously manufactured. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. REMINDER: You must retain the sales slip or sales receipt proving the date of your original purchase in case warranty service is ever required.

Visit our web site:

Eagle Pub. 988-0143-741 Printed in USA 121903
Copyright 2003 All Rights Reserved Eagle Electronics