GETTING STARTED Power The Map Guide Pro operates from AA batteries, a DURACELL NiMH rechargeable battery, or from 5 to 35 volts DC using the external power cable. If the power cable is used, the Map Guide Pro automatically switches to it if the external power is greater than the battery voltage. If for any reason the external power fails, the unit automatically switches to the batteries. BATTERIES The unit requires four AA batteries. We recommend you use alkaline batteries for the best trade-off between battery life and cost. However, you can use nickel-cadmium (ni-cad), or lithium batteries. You can also use rechargeable alkaline batteries such as RayOVac Renewals. With the exception of lithium, none of the above batteries will last as long as standard alkaline batteries. We recommend DURACELL brand, but others will work. Do not use heavy-duty batteries or any type other than the ones listed above. Do not mix different types of batteries. (For example, dont use both alkaline and ni-cad batteries at the same time.) Battery Installation First turn the unit so that its back is facing you. Push the two tabs to the left and remove the battery cover as shown at right. Install the batteries according to this diagram. (Theres a decal in the battery compartment showing the correct polarity, also.) Replace the battery compartment cover and the unit is ready for use. NiMH Battery The DURACELL DR-121 nickel-metal hydride (NiMH) battery replaces the four standard batteries. It is sold as an accessory, (model BR-1) which includes a charger custom designed for the DR-121. The battery never needs to be removed from the unit, since the charger connects to the GPS receiver and charges the DR-121. You can even use the receiver while the battery is charging! To install the NiMH battery, remove the battery cover and place the battery into the compartment as shown on the next page. It will only fit one way, so if its difficult to install, simply turn it over and drop it into place. Replace the compartment cover and follow the charging instructions included with the BR-1.
(Note: The DR-121 is the only battery that can be recharged in this unit! Using the external power cable alone does not charge the battery! You must use a charger supplied by Eagle in order to charge the battery. Also, this charger will only charge a DR-121. It will not charge any other type of battery, including nicads or rechargeable alkallines.)

satellites, and the number shown is not valid. The fix indicator on the left center shows either 2D or 3D. A 2D fix means the unit has locked onto three satellites and has calculated its position. A 3D fix means the unit has locked onto at least four satellites and has calculated both the position and altitude. (Remember, it takes three satellites to determine the position - four to determine position and altitude.) If neither 2D nor 3D are showing, then the unit doesnt have the position or altitude. A battery level indicator on the lower right side of the screen shows approximately how much life is in the batteries. This runs from F (fully charged) to E (expired). A light bulb indicator at the top right corner of the screen appears when the backlights are on. Finding Your Position Auto Search To lock onto the satellites, the GPS receiver needs to know its current position, local time, and date. (Elevation (altitude) is also used in the equation, but its rarely required to determine a position.) It needs this data so that it can calculate which satellites should be in view. It then searches for only those satellites. When your GPS receiver is turned on for the first time, it doesnt know what your position or elevation (altitude) is. It does know the current UTC time and date since these were programmed into it at the factory and an internal clock keeps the time while the unit is turned off. It begins searching for the satellites using the above data that it acquired the last time it was turned on. This probably was at the Eagle factory. Since its almost certain that youre not at the Eagle factory, its probably looking for the wrong satellites. If it doesnt find the satellites its looking for after five minutes, it switches to Auto Search. The receiver looks for any satellite in the sky. Due to advanced technology, the auto search time has shrunk to about five minutes, so the longest time you should ever have to wait is ten minutes from the time you turn the unit on until it locks onto the satellites and shows a position. Once the unit locks onto the satellites, it should take less than a minute to find your position the next time its turned on, provided you havent moved more than approximately 100 miles from the last location it was used. Manual Initialization If you dont want to wait for the Auto Search, then you may be able to speed up the initialization process by using the manual initialization fea6

the current track (direction of travel) you are taking. This is also shown in the TRK (track) box at the top of the screen. On the example shown at right, the track is 355. The current ground speed (GS) shows in the box in the lower center of this screen. When navigating to a waypoint, Nav screen number one looks like the one at right. Bearing to the destination waypoint is in the box in the upper left corner. Bearing is also shown by the large arrow pointing up towards the compass, above the present position arrow. Distance from the present position to the waypoint (DIS) shows beneath the compass on the lower left side of the screen. Lines on either side of the present position show the current cross track error range. Cross track error is the distance you are off-course to the side of the desired course line. The course line is an imaginary line drawn from your position when you started navigating to the destination waypoint. Its shown on the screen as a vertical dotted line. The default for the cross track error range is 0.25 mile. For example, if the present position symbol touches the right cross track error line, then you are.25 mile to the right of the desired course. You need to steer left to return to the desired course. The cross track error is also shown in the XTK box. In the upper right corner is the course (CRS) box showing the direction from your starting position to the waypoint. Remember, a course is a proposed path from the starting position to the destination. Track is your actual direction of travel. A circle depicting your destination (waypoint) appears on the screen as you approach the waypoint as shown on the screen at right. Nav Screen #2 This navigation screen shows all navigation information in large digital numbers. To view this screen, press the PAGES key, then press the up arrow key until the NAV1 label is highlighted. While its highlighted, press the right arrow key. The screen shown at right appears. Press the EXIT key to erase the menu. This screen is composed of eight digital boxes. Track (TRK) and ground speed (GS) data are all that show if youre not navigating to a waypoint. If you are navigat9
ing to a waypoint, then bearing (BRG), distance to waypoint (DIS), estimated time en route (ETE), cross track error (XTK), destination arrow, and the CDI also operate. See below for more information on the CDI. The destination arrow shows the direction to the destination when the top of the screen is pointing in your direction of travel.

In the north-up view shown at right, we're travelling southeast towards camp, saved as waypoint number 14. In this view, the present position indicator appears to move towards the lower right corner of the screen.

NORTH-UP

In the track-up view, the present position moves straight towards the top of the display. A "N" shows to help you see which direction is north when the track-up mode is on. Remember, in the track-up mode, the screen rotates as you change direction. It always keeps your direction of travel (track) heading towards the top of the screen.

TRACK-UP

In the course-up mode, the screen is locked into your original bearing to the recalled waypoint, regardless of your track.

COURSE-UP

To select the desired mode, first press the MENU key, select MAP 1 SETUP, then select MAP OPTIONS. Finally, select ROTATE and press the right or left arrow key until the desired mode appears. Press the EXIT key to erase this menu.
AUTOZOOM This receiver has an autozoom feature that eliminates much of the button pushing that competitive units force you to make. It works in conjunction with the navigation features. First, recall a waypoint. (See the waypoint section for more information on navigating to a waypoint.) Then, with the autozoom mode on, the unit zooms out until the entire course shows, from the present position to the destination waypoint (recalled waypoint). As you travel towards the destination, the unit automatically begins zooming in, one zoom range at a time, keeping the destination on the screen. The screens below show a slice of the progression of a trip near a lake. Screen number one is the start and is on the 6 mile range. Intermediate stages progressively zoom in as it gets closer to the destination.
To use the autozoom feature, first press the MENU key, select Map 1 Setup, then Map Options. Highlight Auto Zoom, then press the right arrow key to turn it on. Press the EXIT key repeatedly to erase the menus. VIEW DESTINATION The GPS receiver normally centers the present position on the screen and moves the map past it. If a waypoint is recalled, the unit can center the waypoint on the screen, instead of the present position. To do this, press the MENU key, select Map 1 Setup, then Map Options. Highlight View Dest, then press the right arrow key to turn it on. Press the EXIT key repeatedly to erase the menus.

select CLOCK ALM SETUP and press the right arrow key. The screen shown below left appears. Now press the right arrow key. The screen below center appears. Using the arrow keys, enter the alarms time. Press

CLOCK ALARM MENU

CLOCK ALARM ADJUST MENU

CLOCK ALARM SET

the ENT key. The unit returns to the clock alarm menu. Highlight the CLOCK ALM OFF ON menu and press the right arrow key to turn it on. Press the EXIT key to erase the menus. The unit returns to the group with the alarms time showing in the clocks window.
Group I This group has estimated time enroute (ETE) at the top of the screen, a trip timer, estimated time of arrival (ETA), and the digital clock.
The trip timer measures the total time you have been travelling. It starts counting when you exceed a preset speed. The default is 5 miles per hour. You can adjust this time from zero to 200 m.p.h. To do this, press the MENU key, then select TRIP TIMER SETUP menu. The screen at right appears. Highlight the START GS label, then press the left or right arrow keys until the desired speed appears. Press the EXIT key to erase this screen.

TRIP TIMER MENU 26

Group J There are three timers on this screen and an odometer (TRIP METER). The trip timer is described in group I. The trip meter measures the distance youve travelled since it was last reset. To reset the trip meter, press the MENU key, then select TRIP METER RESET and press the right arrow key. The unit returns to Group J with the trip meter reset to zero. The up timer starts at zero and counts up. The up timer also has an alarm. The down timer starts from a user setting and counts down to zero.

UP TIMER MENU

UP TIMER SET
To start a timer, first press the MENU key, then highlight the desired timer setup menu. In this example, were using the count up timer, so the UP TIMER SETUP was selected. Now press the right arrow key. A screen similar to the one above center appears. To start the timer, simply highlight the UP TIMER menu, then press the right arrow key. To reset the timer to zero, select the UP TIMER RESET menu. The up timer has an alarm that can be set to sound at a preset time. (For example, one hour from now, three hours, etc.) To set the alarm, highlight the UP TIMER ALM SET and press the right arrow key. The screen at the upper right appears. Using the arrow keys, highlight the first number in the time that you want to set. (The time is in hours, minutes, and seconds) Now press the up or down arrow keys until the desired number shows. Continue until the time shown in the display is correct, then press the ENT key. The unit returns to the timer menu screen. To turn the alarm on, highlight the UP ALARM label. Press the right arrow key. Press the EXIT key to erase the menu. The time you set shows in the UP TIMER box. The timer continues

Project a Waypoint You can save a waypoint even if you dont know its position or location on the map. This unit lets you project the location of a waypoint from a known waypoint using only bearing and distance from the known waypoint. This is useful if you dont know the latitude/longitude of a location, but you do know the distance and bearing from a saved waypoint or your own position. (Note: To project a waypoint from your present position, you must first save your present position as a waypoint.) To use this feature, press the WPT key, then select a waypoint number that you want to save the projected waypoint under. Waypoint 5 is used in this example. Now select CREATE WPT. Finally, select PROJECT POS. The screen shown above appears. The unit needs a location (reference waypoint) to project the new waypoint from. The default reference is waypoint number one. Highlight the REFERENCE WPT label on the Project WPT menu and press the right arrow key. The screen at right appears. Select a waypoint using either the waypoint number, or waypoint list. When youve chosen the waypoint, highlight the SET REFERENCE label and press the right arrow key. The unit returns to the Project WPT screen shown above. The starting waypoint you chose shows in the middle of this screen. Now set the distance from the starting waypoint to the projected waypoint by highlighting the SET DIST label and pressing the right arrow key. Use the arrow keys to set the distance, then press the ENT key when youre finished. The unit returns to the Project WPT screen. Now enter the bearing from the starting waypoint to the projected waypoint by selecting SET BRG from the Project WPT screen. Once youve entered the bearing, the unit returns to the Project WPT screen with the distance and bearing showing at the bottom of the screen, as shown at right. In this example, a distance of 2.5 miles and a bearing of 50 was used. Now press the ENT key. The unit saves the projected location under the waypoint number that you picked at the beginning.
SELECTING A WAYPOINT In order to edit or navigate to a waypoint, you must first select it. There are three ways to do this: by waypoint number, waypoint list, or search by name. All selection methods are on the main waypoint menu shown at right. Waypoint Number To select a waypoint by its number, simply highlight the WPT label at the top of the waypoint menu, then press the left or right arrow keys until the desired waypoint number appears. Waypoint List The waypoint number selection method forces you to scroll through all waypoint numbers, whether theres a location saved in them or not. The waypoint list is composed only of saved waypoints. To use the list, select WPT LIST from the waypoint menu. The screen shown at right appears. The names of all waypoints stored in memory show on this list. Simply highlight the desired waypoint and press the right arrow key to select it. The waypoint menu reappears. (Note: When created, a waypoint is given a default name designated by an asterisk (*). Default names are not shown on the map. The waypoint number is shown until its renamed.) EDITING A WAYPOINT You can customize a waypoint by giving it a name or change its position or icon. To do this, first press the WPT key. The waypoint screen appears. Follow the instructions below for each item. Edit Position Any latitude/longitude can be assigned to any waypoint by manually entering it using the keyboard. First select the waypoint number that you want to save a position under from the waypoint menu. Next, highlight EDIT POSITION and press the right arrow key. The screen shown at right appears. Using the left and right arrow keys, highlight each number in the position and change it using the up and down arrow keys. When youre ready to save this position and return to the waypoint screen, press the ENT key. Note: You can also use this method to change the position of an existing waypoint.

SYSTEM SETUP Many features are listed under the System Setup label on the main menu. These commands affect the basic operation of the unit. To use them, press the MENU key, then System Setup. The screen at right appears. Sound To turn the speaker off, highlight the SOUND label as shown below, then press the left arrow key. Note: This turns the speaker completely off. The unit will not sound a tone when a key is pressed, nor will any alarm sound. The alarm messages will still flash on the screen, however. Contrast To adjust the displays contrast, highlight the Contrast label. Press the right or left arrow keys until the screens contrast is best for the lighting conditions. Backlight The display has lights that can be turned on for night use. To turn the lights on, simply press the PWR key. To turn them off, press the PWR key again. A light bulb indicator on the satellite status screen shows when the lights are on. The default light level is maximum. To reduce the level, select BACKLIGHT, then press the left arrow key until the lights are at the desired level. To increase the light level, press the right arrow key. The lights automatically turn off after 30 seconds to preserve the battery power. It will do this even if the external power is applied to the unit. The time delay is adjustable from 5 to 240 seconds by selecting Light Dly from the System Setup menu. You can also turn the lights on continuously from this menu. Highlight this menu, then press the right arrow key to increase the time the lights are on, the left arrow key to decrease it. Set Local Time When this unit is first initialized, it may not show the correct time for your location due to daylight savings time, time zone variances, and so on. If the time shown on the clock displays is incorrect, select SET LOCAL TIME from the system setup menu and press the right arrow key. The screen shown at the top of the next page appears.
Use the left or right arrow keys to select the number in the current time that you want to change. Use the up or down arrow keys to change the number. Press the ENT key to save the change, the EXIT key to erase the menu without changing it.
Units of Measure You can view data in three different formats: statute, nautical, and metric. The default is statute. The chart below shows the settings for each. Statute Nautical Metric Distance. miles. nautical miles. kilometers Speed. miles per hour.. knots. kilometers per hour Altitude. feet. feet. meters The unit will also show bearing in degrees true or magnetic, and the clock in 12 hour (a.m./p.m.) or 24 hour formats. To change a unit of measure, first select CHANGE UNITS from the System Setup menu. Highlight the desired selection, then press the left or right arrow key. You can change any or all of the settings on this page. When youre finished, press the EXIT key.

Position Format The Map Guide Pro can show the position in degrees, minutes, and thousandths of a minute (36 28.700') or degrees, minutes, seconds, and tenths of a second (36 28' 40.9"). It can also show position in UTM (Universal Transverse Mercator) projection, British, Irish, Swedish, Swiss, Finnish, New Zealand, and Military Grid. UTMs are marked on USGS topographic charts. This system divides the Earth into 60 zones, each 6 degrees wide in longitude. German, Taiwan, British, Irish, Swedish, Swiss, New Zealand, and Finnish grid systems are the national coordinate system used only in their respective countries. In order to use these grid systems, you must be in the respective country. This unit will pick the matching datum for you when you select the grid. See the Datums section for more information. The military grid reference system (MGRS) uses two grid lettering schemes, which are referred to as standard and alternate MGRS on the Map Guide Pro. Your position and datum in use determines which one to use. If you use the standard, and your position is off significantly, then try using the alternate. Note: When the position format is changed, it affects the way all positions are shown on all screens. This includes waypoints. To change the format, highlight the Position Format label on the GPS Setup menu, then press the right arrow key. A screen similar to the one at right appears. Press the up or down arrow keys to select the desired format. Press the EXIT key to erase the position format menu. DATUM Maps and charts are based on a survey of the area thats covered by the map or chart. These surveys are called Datums. Maps that are created using different datums will show the same latitude/longitude in slightly different locations. All datums are named. The GPS system is based on the WGS-84 datum, which covers the entire world. Other datums may also cover the entire world, or just a small portion. By default, your position shows using the WGS-84 datum. However, it can show your position using one of 191 different datums.
To change the datum, first press the MENU key, then highlight the GPS Setup label and press the right arrow key. Now highlight the Select Datum label. Finally, press the right arrow key again. A screen similar to the one at right appears. The WGS-84 label is highlighted. To change it, simply press the up or down arrow keys to highlight the desired datum, then press the ENT key. This selects the datum and erases the select datum menu. To erase the menu without changing the datum, simply press the EXIT key. A list of the datums used by the Map Guide Pro is in the back of this manual. PCF (Position Correction Factor) Another method used to make your display match a chart or map is called PCF or Position Correction Factor. This unit gives you the capability to move or offset the position shown on the display to match one on the chart. The unit will add this offset to all position and navigation displays at all times. Remember, the position error on any radio navigation system is very dynamic and the PCF offset should never be used in an attempt to cancel the error. In general terms, PCF should only be used if your map indicates what the possible error is. PCF should always be reset to zero when youre finished with the chart. For example, suppose you are stopped at a location that is accurately marked on a chart. Your unit shows a longitude position that is.244 minutes east of the one on the chart and.047 minutes north latitude. Using the PCF feature, you can make the Map Guide Pro match the chart youre using. If you move, the unit will continuously add the change to all position, navigation, and mapping displays. This makes it more closely match the datum used by the chart. For this reason, you should be careful when entering the PCF offset. Its saved in memory and doesnt change when the unit is turned off. However, resetting the unit does erase the PCF offset. To change the PCF offset, first press the MENU key, then highlight the GPS Setup label and press the right arrow key. Now highlight the Set

PCF Offset label. Finally, press the right arrow key again. A screen similar to the one at right appears. Now enter the correction for your location. Remember, this is the difference between the location shown on the present position display and the position shown on the chart. In this example, we entered 0 degrees, 0.047 minutes north latitude and 0 degrees, 0.244 minutes east longitude. That is the difference between the present position shown by the Map Guide Pro and the one on our chart. After youve entered the latitude/longitude correction, press the ENT key to accept it. The Map Guide Pro erases the PCF entry screen and returns to the navigation or mapping screens with the correction factor applied.
POSITION PINNING When using a GPS receiver at extremely low speeds, it can have trouble determining your course over ground, or direction youre travelling. This is due in large part to SA, or selective availability. SA is small inaccuracies purposefully put into the GPS satellites signal by the government. This cause wide variations in the track display and other navigation displays when using the unit at slow speeds. If youre using this receiver without DGPS and stop, the position pinning feature locks the present position indicator on the plotter until youve moved a short distance or exceed a very slow speed. This prevents the wandering plot trail seen when youre stopped with position pinning turned off. This also affects the navigational displays. The easiest way to see the effects of S/A is to stand still with the GPS receiver turned on and watch your plot trail with position pinning turned off. Youll see the present position change, speed increase and decrease, and a random plot trail on the plotters screen. If you wish to turn the position pinning feature off, press the MENU key, then highlight the GPS Setup label and press the right arrow key. Now highlight the Pinning label. Finally, press the left arrow key.
ALARMS The Map Guide Pro has several alarms. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint. For example, if you have the arrival alarm set to.1 mile, then the alarm will flash a message when you come within.1 mile of the recalled waypoint. The course deviation indicator alarm (CDI) can warns when your track drifts too far to the right or left of the course line to the waypoint. For example, if the alarm is set to.1 mile, then the alarm flashes a message if you drift.1 of a mile or more to the right or left of the line to the waypoint. The anchor alarm is triggered when you drift outside of a preset radius. Again, using the.1 mile as an example, if youre anchored and your boat moves more than.1 of a mile, the alarm will flash a message and sound a tone. To use any of these alarms, first press the MENU key, then select the ALARMS/CDI menu. A screen similar to the one shown at right appears. Press the up or down arrow key to move the black box to the desired alarm, then press the right arrow key to turn it on. To adjust an alarms distance, move the black box to the alarms DIS menu item, then press the right or left arrow keys to increase or decrease the alarms distance. When youre finished, press the EXIT key to erase this menu. Important Alarm Notes: Anchor Alarm - Since civilian users dont receive the accuracy given to military users, the anchor alarm may be triggered even when youre sitting still. This typically happens when using small (less than.05 mile) anchor alarm ranges. If you have a DGPS beacon receiver connected to the Map Guide Pro, smaller ranges may be usable. Arrival Alarm - If you set the arrival alarms distance to a small number, and you run a route (see the routes section), the Map Guide Pro may not show navigation data to the next waypoint, once you arrive at the first one, since you may not be able to come close enough to the first waypoint to trip the arrival alarm. MESSAGES The DGPS message selections are found on the Alarms/CDI menu shown above. Pressing the EXIT key erases these messages.

The DGPS message appears whenever the unit begins or stops using DGPS data to help determine your position. The default setting for these messages is on. To turn the message off, select the Setup Alarms menu from the main menu, then highlight DGPS MSG and press the left arrow key.
SUNRISE/SET MOONRISE/SET CALCULATOR This unit has a sunrise/sunset and moonrise/moonset calculator that shows this information anywhere or anytime in the world. To use it, press the MENU key, then highlight SUN/MOON CALC and press the right arrow key. Highlight either the sun or moon calculator and press the right arrow key. The screen shown at right appears if you chose the sunrise calculator. (Both calculators work identically. The sunrise/sunset calculator is used for this example.) The sunrise and sunset for todays date appear in the center of the screen. Todays date shows at the top of the screen. If you want to know the sunrise/sunset for a different date, press the ENT key, then enter the new date with the arrow keys. The unit returns to the sunrise/sunset calculator screen with the sunrise and sunset times shown for the date you entered. The sunrise and sunset show for your present position. If you move the plotters cursor to a different position before using this calculator, it will show the sunrise/sunset for the cursors location. The moonrise/moonset calculator works identically to the sunrise/sunset calculator. It looks like the screen at right. A moon symbol shows near the bottom of the screen, showing the approximate phase of the moon. The arrow next to the symbol shows if it is moving towards a full moon (up) or a new moon (down). Press the EXIT key to erase this screen.
SIMULATOR A simulator is built into this unit that has several options. You can use nearly all of the units features - even save and recall waypoints. This is useful for trip planning. To use the simulator, press the MENU key, then press the up or down arrow keys until the SIMULATOR SETUP menu is surrounded by the black box. Now press the right arrow key. The screen shown at right appears. If you simply press the right arrow key, turning the simulator on, the Map Guide Pro will start from your present position and follow a track of 355 at 100 miles per hour. To change either the track or speed, highlight the one you want to change, then press the right or left arrow key. When the numbers are correct, press the EXIT key. Starting Position Normally, the starting position for the simulator is your present position. If you want to change the starting position, highlight the SET START WPT label on the Simulator Setup menu, then press the right arrow key. The screen shown at right appears. You can select any waypoint as the simulators starting point. Select the starting point by pressing the right arrow key on the WPT# label until the desired starting waypoint number appears. Now highlight the SET SIM START label and press the right arrow key. The unit returns to the Simulator Setup menu using the specified waypoint as the starting waypoint. Use Arrow Keys to Steer This option lets you change both the course and speed on the screen as the simulator is running. To do this, highlight the STEER WITH ARROWS label on the Simulator Setup screen, then press the right arrow key. The screen shown at right appears. Use the up and down arrow keys to increase or decrease the speed. Use the right and left arrow keys to change the track. When youre finished changing the track and speed, press the EXIT key to erase the menus.

DEFINITION OF TERMS/ABBREVIATIONS Due to space considerations, the digital displays use abbreviations for some names. They are as follows: ALT.. Altitude - Your height above sea level. BRG. Bearing - The direction from your present position to a waypoint. CDI.. Course Deviation Indicator - Shows your distance to the side of the desired course line. CLOCK. Your local time. TRK. Track - The direction youre travelling. DIS.. Distance - Distance remaining between your present position and a waypoint. DNT/UPT. Countdown timer (DNT) and Count up timer (UPT) ETA.. Estimated Time of Arrival ETE. Estimated Time En route ICON. A symbol you can place on the map, representing a landmark. POSITION. Your present position. GS. Ground Speed - Your actual speed. UTC. Coordinated Universal Time - Time at the prime meridian at Greenwich, England. Formerly known as GMT. VOLTS.. Electrical system voltage. VMG. Velocity Made Good - Your ground speed towards a recalled waypoint, airport, etc.

DATUMS

WGS 84.. WGS 1984 DEFAULT Default ADINDAN.. Adindan MEAN Mean for Ethiopia, Sudan ADINDAN.. Adindan BURKINA Burkina Faso FASO ADINDAN.. Adindan CAMEROON Cameroon ADINDAN.. Adindan ETHIOPIA Ethiopia ADINDAN.. Adindan MALI Mali ADINDAN.. Adindan SENEGAL Senegal ADINDAN.. Adindan SUDAN Sudan AFGOOYE. Afgooye SOMALIA Somalia AIN EL ABD. Ain el Abd Bahrain BAHRAIN AIN EL ABD. Ain el Abd SAUDI Saudi Arabia ARABIA ANNA 1 ASTRO. Anna 1 Astro COCOS Cocos Islands ISLANDS ANTIGUA.. Antigua Island Astro 1943 ISLAND Antigua (Leeward Islands) ASTRO 1943 ARC 1950. Arc 1950 MEAN Mean for Botswana, Lesotho, Malawi, Swaziland, Zaire, Zambia, Zimbabwe ARC 1950. Arc 1950 - Botswana BOTSWANA ARC 1950. Arc 1950 - Burundi BURUNDI ARC 1950. Arc 1950 - Lesotho LESOTHO ARC 1950. Arc 1950 - Malawi MALAWI ARC 1950. Arc 1950 - Swaziland SWAZILAND ARC 1950. Arc 1950 - Zaire ZAIRE ARC 1950. Arc 1950 - Zambia ZAMBIA ARC 1950. Arc 1950 - Zimbabwe ZIMBABWE ARC 1960. Arc 1960 - Mean for Kenya, MEAN Tanzania ASCENSION.. Ascension Island 1958 ISLAND Ascension Island 1958 ASTRO BEACON. Astro Beacon E 1945 - Iwo Jima E 1945 IWO JIMA ASTRO DOS 714. Astro DOS 71/4 - St Helena Island ST HELENA ISLAND ASTRO TERN. Astro Tern Island (FRIG) 1961 ISLAND Tern Island 1961 ASTRONOMICAL. Astronomical Station 1952 STATION 52 Marcus Island MARCUS ISLE AUSTRALIAN. Australian Geodetic 1966 GEODETIC Australia & Tasmania 1966 AUSTRALIAN. Australian Geodetic 1984 GEODETIC Australia & Tasmania 1984 AYABELLE. Ayabelle Lightlhouse - Djibouti LIGHTHOUSE DJIBOUTI BELLEVUE. Bellevue (IGN) - Efate & (IGN) EFATE Erromango Islands ERRAOMANGO BERMUDA. Bermuda 1957 - Bermuda 1957 BISSAU. Bissau - Guinea-Bissau GUINEA BOGOTA. Bogota Observatory - Colombia OBSERVATORY COLOMBIA BUKIT RIMPAH. Bukit Rimpah - Indonesia (Bangka INDONESIA & Belitung Islands) CAMP AREA.. Camp Area Astro - Antarctica ASTRO (McMurdo Camp Area) ANTARCTICA CAMPO. Campo Inchauspe - Argentina INCHAUSPE ARGENTINA CANTON ASTRO. Canton Astro 1966 - Phoenix 66 PHOENIX Islands ISLANDS CAPE. Cape - South Africa SOUTH AFRICA CAPE. Cape Canaveral - Bahamas, CANAVERAL Florida BAHAMAS FL

CARTHAGE. Carthage - Tunisia TUNISIA CH-1903. Switzerland CHATHAM. Chatham Island Astro 1971 ISLAND ASTRO New Zealand (Chatham Island) NEW ZEALAND CHUA ASTRO. Chua Astro PARAGUAY Paraguay CORREGO. Corrego Alegre ALEGRE Brazil BRAZIL DABOLA. Dabola GUINEA Guinea DJAKARTA. Djakarta (Batavia) (BATAVIA) Indonesia (Sumatra) INDONESIA DOS 1968. DOS 1968 NEW GEORGIA New Georgia Islands ISLANDS (Gizo Island) EASTER. Easter Island 1967 ISLAND Easter Island 1967 EUROPEAN. European MEAN Mean for Austria, Belgium, WESTERN Denmark, Finland, France, West Germany, Gibralter, Greece, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland EUROPEAN. European MEAN Mean for Austria, Denmark, CENTRAL France, West Germany, Netherlands, Switzerland
EUROPEAN. European ITALY Italy (Sardinia) (SARDINIA) EUROPEAN. European ITALY (Sicily) (SICILY) EUROPEAN. European Malta MALTA EUROPEAN. European SPAIN Portugal, Spain PORTUGAL EUROPEAN. European Mean for Austria, Finland, MEAN Netherlands, Norway, Spain, Sweden, Switzerland FORT THOMAS.. Fort Thomas, NEVIS Nevis, St. Kitts ST. KITTS (Leeward Islands) GAN 1970. Gan 1970 REPUBLIC OF Republic of Maldives MALDIVES GEODETIC. Geodeic Datum 1949 DATUM 1949 New Zealand NEW ZEALAND GRACIOSA. Graciosa Base SW 1948 BASE SW Azores (Faial, Graciosa, Pico, 1948 AZORES Sao Jorge, Terceira) GUAM.. Guam Guam GUNUNG.. Gunung Segara SEGARA Indonesia (Kalimantan) INDONESIA GUX 1 ASTRO. GUX 1 Astro GUADALCANAL Guadalcanal Island ISLAND HERAT NORTH.. Herat North AFGHANISTAN Afghanistan HJORSEY. Hjorsey Iceland ICELAND HONG KONG. Hong Kong Hong Kong HU-TZU-SHAN. Hu-Tzu-Shan TAIWAN Taiwan INDIAN. Indian BANGLADESH Bangladesh INDIAN. Indian INDIA NEPAL India, Nepal INDIAN 1954. Indian - 1954 THAILAND Thailand, Vietnam VIETNAM INDIAN 1975. Indian - 1975 THAILAND Thailand
EUROPEAN. European MEAN Mean for Iraq, Israel, Jordan, MIDDLE EAST Lebanon, Kuwait, Saudi Arabia, Syria EUROPEAN. European Cyprus CYPRUS EUROPEAN. European Egypt EGYPT EUROPEAN. European GREAT England, Channel Islands, Ireland, BRITAIN Scotland, Shetland Islands EUROPEAN 50.. European 1950 FINLAND Finland, Norway NORWAY EUROPEAN. European Greece GREECE EUROPEAN. European Iran IRAN

This UPS shipping offer is good only in the continental United States (excludes Alaska and Hawaii).
KEEP THIS LABEL! YOU WILL NEED IT IF YOU EVER NEED TO RETURN YOUR UNIT TO THE FACTORY FOR REPAIR.
Accessory Ordering Information
To order accessories such as power cables, please contact: 1) Your local marine dealer. Most quality dealers that handle marine electronic equipment should be able to assist you with these items. Consult your local telephone directory for listings. 2) LEI Extras, Inc. P.O. Box 129 Catoosa, OK 74015-0129 or call 800-324-0045 (USA orders only.) Eagle Electronics may find it necessary to change or end our shipping policies, regulations, and special offers at any time. We reserve the right to do so without notice.
EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY
We", our, or us refers to EAGLE ELECTRONICS, a division of LEI, the manufacturer of this product. You or your refers to the first person who purchases this product as a consumer item for personal, family, or household use. We warrant this product against defects or malfunctions in materials and workmanship, and against failure to conform to this products written specifications, all for one year (1) from the date of original purchase by you. WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship, or any nonconformity with the products written specifications, occurred within one year from the date of your original purchase, which must be substantiated by a dated sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your original purchase date will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain without charge a replacement of the product or a refund for the product. THIS REPAIR, REPLACEMENT, OR REFUND (AS JUST DESCRIBED) IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT, MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty does NOT apply in the following circumstances: (1) when the product has been serviced or repaired by anyone other than us, (2) when the product has been connected, installed, combined, altered, adjusted, or handled in a manner other than according to the instructions furnished with the product, (3) when any serial number has been effaced, altered, or removed, or (4) when any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owners manual for the product. We reserve the right to make changes or improvements in our products from time to time without incurring the obligation to install such improvements or changes on equipment or items previously manufactured. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. REMINDER: You must retain the sales slip or sales receipt proving the date of your original purchase in case warranty service is ever required. This warranty does not apply to any database or its contents supplied initially with this product. For warranty information on the databases and their contents, please refer to the Databases Limited Warranty included with this product. EAGLE ELECTRONICS PO BOX CATOOSA, OK 74015

GPS Units Compatible with Maptechs Terrain Navigator and Terrain Navigator Pro

Updated 6/7/04

There are two reasons to connect a GPS to your PC - Real-time position tracking on the PC screen and transferring information between the PC and GPS. Virtually any GPS unit can be used for real-time positioning, but transferring routes, waypoints, and tracks to and from a GPS requires special compatibility.
Real-time Position Tracking on the PC screen
Connect any industry-standard NMEA 0183 GPS to a PC COM port, and Terrain Navigator (Pro) will display your realtime position on top of a Maptech topo map (or aerial photo with the Pro version). Most GPS receivers made in the past 5+ years output the NMEA 0183 (version 1.5, 2.0/2.1, or 2.3) data language. GPS receivers can be connected by a serial cable (sold by the GPS manufacturers) to your PC through a standard 9-pin serial port. If your PC only has USB connections, you can connect a GPS serial cable to a serial-to-USB hub that will connect it to the USB port on your PC.
Transferring Waypoint, Route and Track Information Between the PC and GPS
Terrain Navigator (Pro) can transfer Waypoint, Route and Track Information between the PC and specific GPS models. Many users find it easier to plan routes on the PC than to hand-key them into their GPS, and Terrain Navigator (Pro) facilitates this. Unlike with Real-Time positioning, there is no industry-standard for transferring Waypoint, Route and Track information. Each GPS model has its own specific drivers for communicating this information. Below is Information about specific GPS Manufacturers and models in alphabetical order. Real-time Tracking on the PC screen Any unit that supports the industry standard NMEA 0183 interface specification (version 1.5, 2.0/2.1or 2.3) may be used for realtime tracking in Terrain Navigator (Pro). In the Terrain Navigator (Pro) GPS Setup, choose NMEA - Generic as the manufacturer. Real-time Tracking on the PC screen Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS from GPS Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS to and from GPS
ANY MANUFACTURER (NMEA 0183 GPS)

BRUNTON Multi-Navigator

This GPS unit is not capable of receiving tracks. The unit stores one track log, which you may transfer to Terrain Navigator (Pro) for display on the charts. Real-time Tracking on the PC screen Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS to and from GPS
DELORME Earthmate (9-pin serial) Tripmate
Note on Delormes USB Earthmate GPS: We do not recommend this GPS since Delorme does not support its use with non-Delorme products. We have posted a technical document on the support section of www.maptech.com that explains how to set up a virtual COM port for use with this GPS. If you do not already own this model, we recommend using an alternative GPS receiver on this list. Real-time Tracking on the PC screen Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS to and from GPS
FURUNO GP-31 GP-1650DF GP-1700C
Note that Furuno GPS units are not capable of storing tracks.

GARMIN

Real-time Tracking on the PC screen
Transfer of WAYPOINTS to and from GPS
Transfer of ROUTES to and from GPS
Transfer of TRACKS to and from GPS
Below is a list of units that our support and development staff have tested for use with Terrain Navigator (Pro). eMap eTrex (Legend, Mariner, Summit, Venture & Vista) GPS 12 (12, 12cx, 12xl, 12Map) GPS 38 GPS 45 & 45xl GPS 48 GPS 76, GPSMAP 76 GPS 126 GPS 128 GPSMAP 130 GPSMAP 168 Sounder GPSMAP 175 GPSMAP 176/176C GPSMAP 295 Garmin II & II+ Garmin III & III+ Garmin V StreetPilot Rhino 110/120

UNTESTED GARMIN UNITS: Cross-compatibility: Garmin has a wide range of GPS models. Many of them have different shapes, sizes and colors but share similar internal software. Maptech has created a number of software drivers to support Garmin models. If your model isnt listed above, theres a good chance it works, but will require picking another models driver. Often, a single driver will work with multiple Garmin units. Below is a cross-compatibility list of Garmin models, based solely on information from other customers. If you have additions or corrections for this list, we and your fellow users would appreciate hearing about them. Please call us at 888-839-5551 or email sales@maptech.com with additions or corrections. Also note that Maptech technical support may not be able to fully assist you with the hookup and use of these units. GPS Model GPS 17N GPS 40 Reported Working As NMEA Generic GPS 45 Notes Real-time tracking only
GPSMAP 60C GPSMAP 76 This configuration requires using a Garmin PC interface cable (Garmin Part # 010-10141-00), plus a serial-to-USB adapter if no 9-pin serial port is available on the PC. The number of transferable waypoint, routes and tracks may be limited. Maptech does not have drivers to use the Garmin USB cable included with the GPSMAP 60C. GPS72 GPS 12 One user reported as working; another reports that marker names dont transfer correctly.

GPS 75 GPSMAP 76C

GPS 45 GPSMAP 76 GARMIN Continued on next page
GPS Model GPS 128 GPS 152 GPSMAP 180 GPSMAP182 GPSMAP188 Sounder GPSMAP 215 GPSMAP 225 GPSMAP 230
Reported Working As GPS 12XL eTrex Garmin II GPSMAP 76 GPSMAP 76 GPS 12XL GPS 126 GPSMAP 130

Also works as GPS 45xl

GPSMAP 276C GPSMAP 76 This configuration requires using a Garmin PC interface cable (Garmin Part # 010-10514-00), plus a serial-to-USB adapter if no 9-pin serial port is available on the PC. The number of transferable waypoint, routes and tracks may be limited. Maptech does not have drivers to use the Garmin USB cable included with the GPSMAP 276C. GPSMAP 2006/2006C GPSMAP 2010/2010C StreetPilot III Real-time Tracking on the PC screen GPS 76 GPSMAP 76, also GPS 38 eMap Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS to and from GPS Also works as GPS 38

LOWRANCE

Below is a list of units that our support and development staff have tested for use with Terrain Navigator (Pro). Eagle Explorer Eagle Map Guide Eagle Map Guide Pro GlobalMap 100 GlobalNav 12 GlobalNav 212
UNTESTED LOWRANCE UNITS - Cross-compatibility: Lowrance has a wide range of GPS models. Many of them have different shapes, sizes and colors but share similar internal software. Maptech has created a number of software drivers to support Lowrance models. If your model isnt listed above, theres a good chance it works, but will require picking another models driver. Often, a single driver will work with multiple Lowrance units. Below is a cross-compatibility list of Lowrance models, based upon information received from their support staff. If you have additions or corrections for this list, we and your fellow users would appreciate it. Please call us at 888-839-5551 or email sales@maptech.com with additions or corrections. Also note that Maptech technical support may not be able to fully assist you with the hookup and use of these units. GPS Model Eagle Accunav Sport Eagle Expedition/Expedition II Eagle Journey GlobalMap 12 GlobalMap Sport GlobalNav 200 Reported Working As Eagle Map Guide Pro Eagle Map Guide Pro Eagle Map Guide Pro Eagle Map Guide Pro Eagle Map Guide Pro Eagle Map Guide Pro Tracks may appear shifted in position. Notes

MAGELLAN

Real-time Tracking on the PC screen
Transfer of WAYPOINTS to and from GPS
Transfer of ROUTES to and from GPS
Transfer of TRACKS from GPS
Below is a list of units that our support and development staff have tested for use with Terrain Navigator (Pro). 2000XL & 4000XL Meridian Tracker & ColorTRAK GPS 315 & 320 MAP 330
* Magellan GPS units are not capable of receiving tracks. The unit stores one track log, which you may transfer to Terrain Navigator Pro for display on the maps. UNTESTED MAGELLAN UNITS: Cross-compatibility: Magellan has a wide range of GPS models. Many of them have different shapes, sizes and colors but share similar internal software. Maptech has created a number of software drivers to support Magellan models. If your model isnt listed above, theres a good chance it works, but will require picking another models driver. Often, a single driver will work with multiple Magellan units. Below is a cross-compatibility list of Magellan models, based upon information received from their support staff. If you have additions or corrections for this list, we and your fellow users would appreciate hearing about them. Please call us at 888-839-5551 or email sales@maptech.com with additions or corrections. Also note that Maptech technical support may not be able to fully assist you with the hookup and use of these units. GPS Model 3000XL Meridian GPS Meridian Gold Meridian Platinum NAV 6000 SporTrack SporTrack Pro Real-time Tracking on the PC screen Reported Working As 2000XL GPS 315 GPS 315 2000XL 2000XL Tracker Tracker Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS to and from GPS Also works as 4000XL Notes Also works as 4000XL
NORTHSTAR 941, 951 & 952
Northstar GPS units are not capable of storing tracks. Real-time Tracking on the PC screen Transfer of WAYPOINTS to and from GPS Transfer of ROUTES to and from GPS Transfer of TRACKS to and from GPS
STANDARD HORIZON GPS Chart 150
Standard Horizon GPS units are not capable of storing tracks.
TRIMBLE GeoExplorer II Scoutmaster
Real-time Tracking on the PC screen
Transfer of WAYPOINTS to and from GPS
Trimble handheld GPS units are not capable of storing tracks or routes. Instead, coordinate data is stored in waypoint form (single locations not grouped in sequence). Mobile GPS