ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE. To locate your nearest Emerson Authorized Service Center or general service procedure, please call 1-800-256-2487 or write to the following: FUNAI CORPORATION, INC. Customer Service 100 North Street; Teterboro, NJ 07608 Tel :1-800-256-2487 http://www.funai-corp.com PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
0EMN02206 Printed in Malaysia L6406UG * * * * *
Place your TV in a room with adequate ventilation. Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight. Do not place your TV on soft surfaces, such as rugs or blankets. Leave enough room for air to circulate around the bottom, top and back of the set.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase Dealer Phone No. Dealer Purchase from Model No. Dealer Address Serial No. This Owners Manual is made of recycled paper.
IF YOU NEED ADDITIONAL ASSISTANCE FOR SET-UP OR OPERATING AFTER READING OWNERS MANUAL, PLEASE CALL TOLL FREE 1-800-256-2487 OR VISIT OUR WEB SITE AT http://www.funai-corp.com
ANTENNA/CABLE CONNECTIONS
UHF/VHF Rod Antenna (Not supplied)

VHF Antenna

*Some cable TV systems use
scrambled signals and require a special converter to receive these channels. Consult your local cable company.
CATV Box * or Satellite Box (Not supplied)
Before plugging the UHF/VHF Rod Antenna into the ANT(enna). IN jack, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the ANT(enna). IN jack.

Bent pin

(Not supplied) UHF Antenna (Not supplied)
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

ANT.IN

Cable Plug
(Needs to be straightened) (Straight pin) OR

ANT. IN

75-ohm Coaxial Cable
From Cable System or Satellite Antenna 75-ohm Coaxial Cable From Cable System
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR VITER LES CHOC LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
VHF/UHF Combiner (Not supplied) VHF/UHF Combination Antenna (Not supplied)

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.
Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

Caption Mode

(1) Characters can be displayed on the TV screen when the received broadcast signal contains the Caption Signals. (2) Paint-on mode: Displays input characters on the screen immediately. Pop-on mode: Once characters are stored in memory, it is displayed all at once. Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines) Note: If the CAPTION C1 or C2 is selected but the caption signal is not included, characters will not be displayed.
Notes: (1) When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a VCRs video output channel (CH3 or CH4), your TV may not display the correct caption or text. (2) Captions and texts may not match the TV voice exactly. (3) Interference may cause the closed caption system not to function properly. (4) The caption or text characters will not be displayed while the menu display or functions display is shown. (5) If you see this screen :

Text Mode

(1) Displays the text on the screen by scrolling (max. 7 lines) (2) If the received broadcast signal does not contain the caption or text signal, no change will occur. If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].
L6406.QX33 03.4.25 11:11 AM Page 2

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANY-ING THE APPLIANCE. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTI-TUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE GROUND CLAMP
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

IMPORTANT SAFEGUARDS

1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. 5. Cleaning-Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6. Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards. 7. Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting of the appliance should follow the manufacturers instructions and should use a mounting accessory recommended by the PORTABLE CART WARNING manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

S3126A

AMEUBLES- Cet appareil ne doit SYMBOLE D'AVERTISSEMENT POUR LES COMPOSANTES tre plac que sur un meuble (avec APPAREIL ET MEUBLE A ROULETTES ou sans roulettes) recommand par le fabricant. Si vous linstallez sur un meuble roulettes, dplacez les deux ensembles avec prcaution. Un arrt brusque, lutilisation dune S3126A force excessive et des surfaces irrgulires risquent de dstabiliser lensemble et de le renverser. 9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. 10. Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions. 11. Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12. Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

S2898A

receptacles, and the point where they exit from the appliance. 13. Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A) 14. Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges. 15. Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17. Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.

18. Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. Damage Requiring Service-Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the TV. c. If the TV has been exposed to rain or water. d. If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation. e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in performance-this indicates a need for service. 20. Replacement Parts-When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards. 21. Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition. 22. Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - REAR PANEL -
MENU VIDEO L AUDIO R HEAD PHONE

VOLUME

CHANNEL

POWER POWER

1 - REMOTE CONTROL -
9. CHANNEL NUMBER buttons- Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel. +100 button- Press to select cable channels which are equal or greater than number 100. 10.MUTE button- Press the MUTE button to turn off the sound portion of the TV program. (Volume level display turns LIGHT RED from LIGHT BLUE.) Press the MUTE button again or press the VOL(ume) L or M button to restore sound. 11.CHANNEL RETURN button- Press this button to go back to the previously viewed channel. For example, pressing the CHANNEL RETURN button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3. 12.DISPLAY button- Press to display the channel number on the screen. If you press it again, the channel number will disappear. 13.SLEEP button- Press the SLEEP button to display the sleep timer and start the function. The shut off time can be determined by the number of times you press the button. (0, 10, 20, 30,.90, 0 minutes) 14.GAME button- Press to set the Game mode and external input mode at the same time. Press the GAME button again to exit the mode.

L6406.QX33 03.4.25 11:11 AM Page 3

PREPARATION FOR USE

LANGUAGE SELECTION
If you want to change the language of the on-screen menu, follow the procedure below. 1) Connect the power cord to a standard AC outlet. 2) Press the POWER button to turn on the TV. 3) Press the MENU button so that the menu display appears on the TV screen. 4) Press the CH(annel) L or M button to point to "[ENGLISH]". 5) Select "ENGLISH" or "ESPAOL" = Spanish by using the VOL(ume) L or M button. 6) Press the MENU button to exit the menu.
PICTURE CHANNEL SET [ENGLISH]ESPAOL V-CHIP SET UP CAPTION [OFF]

CHANNEL PRESETTING

NOTE:You MUST PRESET channels BEFORE using CHANNEL L or M button. To preset a channel or to change a preset channel, follow the procedure below. 1) Press the POWER button to turn on the TV. 2) Press the MENU button so that the menu display appears PICTURE CHANNEL SET on the TV screen. [ENGLISH]ESPAOL 3) Press the CH(annel) L or M button to point to "CHANNEL SET". V-CHIP SET UP CAPTION [OFF] Then, press the VOL(ume) L button. 4) Press the CH(annel) L or M button to point to "AUTO MEMO". Then, press the VOL(ume) L button. PICTURE CHANNEL SET The tuner scans and memorizes all active channels in your area. [ENGLISH]ESPAOL G The TV distinguishes between standard TV channels and cable channels. V-CHIP SET UP CAPTION [OFF] G When AUTO MEMO action is completed, the lowest memorized channel reappears on the screen. G When you press the CH(annel) L or M button after selecting AUTO ADD/DELETE MEMO, the tuner will stop at the memorized channels only. AUTO MEMO STEREO [OFF] G The TV may recognize TV channels to be CATV channels by the receiving conditions. In this case, try AUTO MEMO action again in the fine receiving conditions.
[ADD/DELETE FUNCTION] 1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the CH(annel) L or M button to point to "CHANNEL SET". Then, press the VOL(ume) L button. 3) Press the VOL(ume) L button so that "ADD/DELETE" is selected. 4) Use the CH(annel) L or M button to select the channel you wish to put into memory or to erase from memory. Note: The display will return to the screen in about 10 seconds. Perform "ADD/DELETE" function while this display appears on the screen. G Press the VOL(ume) L or M button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory. G Press the VOL(ume) L or M button to light up the channel number in LIGHT RED if you wish to erase the channel from memory. 5) Press the MENU button to exit the menu.

ADD/DELETE AUTO MEMO STEREO [OFF]

STEREO SOUND SYSTEM

This function is suppresses noise, restores the dynamic range and electronically expends the stereo signal to create a more specious sound effect. 1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the CH(annel) L or M button to point to "CHANNEL SET". Then, press the VOL(ume) L button. 3) Press the CH(annel) L or M button so that "STEREO" is selected. 4) Press the VOL(ume) L or M button to select the stereo mode on or off. Stereo sound is effective when the "STEREO" is on.
ADD/DELETE AUTO MEMO STEREO [ON]

RESUME FUNCTION

If the power fails or is disconnected while the TV is powered on, the TV will turn on automatically when the power resumes.

OPERATIONS

WATCHING A TV PROGRAM
1) Press the POWER button to turn on the TV. 2) Select the desired channel with the CH(annel) L or M button. 3) Adjust the volume to the desired listening level using the VOL(ume) L or M button. 4) Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)

PICTURE ADJUSTMENT

1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the VOL(ume) L button so that "PICTURE" is selected. 3) Select the feature you wish to adjust with the CH(annel) L or M button and adjust it with the VOL(ume) L or M button. GAME MODE Set to the most suitable position for TV GAME. [+] : ON [-] : OFF BRIGHT Adjust until the whitest parts of the picture are as bright as you prefer. [+] : increase brightness [-] : decrease brightness CONTRAST Adjust to increase or decrease contrast. [+] : increase contrast [-] : decrease contrast COLOR Adjust to be brilliant or pale color. [+] : be brilliant color [-] : be pale color TINT Adjust to obtain natural skin tones. [+] : greenish tone [-] : reddish tone Notes: G + is achieved by pressing the VOL(ume) L button and - by pressing the VOL(ume) Mbutton. : Press the CH(annel) L or M button.
G In the above steps, the picture adjustment

SETTING THE SLEEP TIMER

The sleep timer function enables you to shut off the power without pressing the POWER button after a desired time period. 1) Press the POWER button to turn on the TV and press the SLEEP button on the remote control. SLEEP 10 2) You may change the sleep time with pressing the SLEEP button on the remote control repeatedly. The timer is set up to 90 minutes, 10 minutes each time the SLEEP button is To cancel the sleep timer: pushed. (The timer display counts up and sleep timer will Press the SLEEP button repeatedbe displayed on the screen when you press the SLEEP ly until "SLEEP 0" is displayed. button on remote control.) Note: When you disconnect the unit from the AC outlet, or if you have a power failure, the sleep time will be lost.
display will disappear from the TV screen after about 10 seconds unless you press any buttons, even though you may not be finished. Press the MENU and VOL(ume) L button so that "PICTURE" is selected. Then, press the CH(annel) L or M button repeatedly until the display returns to the screen. G If you adjust the other Picture control after you set the Game mode to [ON], the Game mode is set to [OFF] automatically. [USING THE GAME BUTTON] You may also set the Game mode and external input mode at the same time by pressing the GAME button on the remote control. GAME appears on the TV screen. G To exit the Game mode and external input mode, press the GAME button on the remote control again. G To cancel the Game mode only, adjust the picture control. In this case, VIDEO instead of GAME appears on the TV screen. G When you press the GAME button if the TV is off, the TV turns on and will be in the Game mode and external input mode automatically.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program. 1) Press the MENU button so that the menu display appears on the TV screen. 2) Press the CH(annel) L or M button to point to "CAPTION". 3) Press the VOL(ume) L or M button to select the mode you wish. 4) When done, press the MENU button to exit the menu.
PICTURE CHANNEL SET [ENGLISH]ESPAOL V-CHIP SET UP CAPTION [ T1] PICTURE CHANNEL SET [ENGLISH]ESPAOL V-CHIP SET UP CAPTION [ T2]
: Press the VOL(ume) L or M button.
PICTURE CHANNEL SET [ENGLISH]ESPAOL V-CHIP SET UP CAPTION [OFF] PICTURE CHANNEL SET [ENGLISH]ESPAOL V-CHIP SET UP CAPTION [ C1]

PICTURE CHANNEL SET [ENGLISH]ESPAOL V-CHIP SET UP CAPTION [ C2]

[-] GAME MODE [+] OFF ON

BRIGHT

CONTRAST

L6406.QX33 03.4.25 11:11 AM Page 4

OPERATIONS (Continued)

V-CHIP SET UP
V-CHIP enables parents to prevent their children from watching inappropriate material on TV. V-CHIP reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels, and Emergency Broadcast System signals), then denies access to programming if the program's rating meets the limitations you select. In this case, "PROTECTED PROGRAM by." message appears on the TV screen. To block ratings, follow the steps below. G Programming may be rated by the Motion Picture Association of America (MPAA) or according to the Television Parental Guidelines. In order to block any inappropriate programming, set your limits in both places (MPAA RATING and TV RATING). G You cannot access the menu when the "PROTECTED PROGRAM by." message appears. In this case, change to the unblocked channel, then press the MENU button. [MPAA RATING SET UP] 1 Press the MENU button so that the menu display appears on the TV screen. 2 Press the CH(annel) L or M button to point to "V-CHIP SET UP". Then, press the VOL(ume) L button. 3 Press the CH(annel) L or M button to point to "MPAA RATING". Then, press the VOL(ume) L button. 4 Press the CH(annel) L or M button to point to your desired item. Then, press the VOL(ume) L button to select [BLOCK] or [VIEW].
<Selection> G: PG: PG-13: R: NC-17: X: <Rating Category Explanations> General Audience Parental Guidance suggested. Unsuitable for children under 13 Restricted; under 17 requires accompanying parent or adult guardian No one under 17 admitted Mature audience only
[TV RATING SET UP] 1 Press the MENU button so that the menu display appears on the TV screen. 2 Press the CH(annel) L or M button to point to "V-CHIP SET UP". Then, press the VOL(ume) L button. 3 Press the CH(annel) L or M button to point to "TV RATING". Then, press the VOL(ume) L button. 4 Press the CH(annel) L or M button to point to your desired item. Then, press the VOL(ume) L button to select [BLOCK] or [VIEW].
<Selection> TV-Y: TV-Y7: TV-G: TV-PG: TV-14: TV-MA: <Rating Category Explanations> Appropriate for all children Appropriate for children seven and older General Audience Parental Guidance suggested. Unsuitable for children under 14 Mature audience only

TV RATING MPAA RATING

TV-Y TV-Y7 ( TV-G TV-PG ( TV-14 ( TV-MA (
[VIEW] ) [VIEW] [VIEW] ) [VIEW] ) [VIEW] ) [VIEW]
G When you select the rating category and turn it [BLOCK], the higher rating will turn [BLOCK]

automatically. Also, the lower rating will turn [VIEW] automatically.
G When you turn "TV-Y" to [BLOCK] or [VIEW], the all ratings will turn to [BLOCK] or

[VIEW] automatically.

G When you turn "TV-MA" to [VIEW], the all ratings will turn to [VIEW] automatically.

G PG PG-13 R NC-17 X

[VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK]
When you select TV-Y7, TV-PG, TV-14, or TV-MA and you press the VOL(ume) L button, the sub-ratings will appear on the TV screen. If you select the rating category (example: TV-PG) and turn it [BLOCK] or [VIEW], the sub-ratings (example: V for Violence) will turn [BLOCK] or [VIEW] automatically. You can set the sub-ratings to [BLOCK] or [VIEW] individually when the [BLOCK] rating category is set to [BLOCK]. To set the sub-ratings individually, follow TV-Y7 the steps below. FV [BLOCK] Press the CH(annel) L or M button to select "FV" (Fantasy Violence). Then, press the VOL(ume) L button to select [BLOCK] or [VIEW]. G When you select [TV-PG], [TV-14] or [TV-MA]: Press the CH(annel) L or M button to select "D"(Suggestive Dialog), "L"(Coarse Language), "S"(Sexual Situation), or "V"(Violence). Then, press the VOL(ume) L button to select [BLOCK] or [VIEW]. Note: When you select [TV-MA], "D" does not appear on the TV screen. G The sub-ratings which set to [BLOCK] appears next to the rating category in the TV RATING menu. 5 Press the MENU button to exit the menu.
G When you select [TV-Y7]:

TV-PG D L S V

[BLOCK] [BLOCK] [BLOCK] [BLOCK] [BLOCK]
automatically. Also, the lower rating will turn [VIEW] automatically. G When you turn "G" to [BLOCK] or [VIEW], the all ratings will turn to [BLOCK] or [VIEW] automatically. G When you turn "X" to [VIEW], the all ratings will turn to [VIEW] automatically. 5 Press the MENU button to exit the menu.
TV-Y [VIEW] ) [VIEW] TV-Y7 ( [BLOCK] TV-G TV-PG (DLSV) [BLOCK] TV-14 (DLSV) [BLOCK] TV-MA ( LSV) [BLOCK]

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. Before arranging for service, check these items. It could save your time and money.
Poor Reception on Some Channels Different color marks on screen Remote Control Doesnt Work

MAINTENANCE

CABINET CLEANING
G Wipe the front panel and other exterior sur-

SUPPLIED ACCESSORIES

Remote control unit (NE127UD) Batteries ("AA" x 2) Owners Manual (0EMN02206)
Lines or Streaks in Picture

Sound OK, Picture Poor

Picture OK, Sound Poor

Picture Rolls Vertically

Ghosts in picture

Picture Distorted

QUICK SERVICE CHECK LIST

No Picture or Sound

Bars On Screen

Picture Blurred

Weak Picture
faces of the TV with a soft cloth immersed in lukewarm water and wrung dry. G Never use a solvent or alcohol. Do not spray insecticide liquid near the TV. Such chemicals may cause damage and discoloration to the exposed surfaces.

PROBLEM

No Color

PICTURE TUBE CLEANING

Wipe the picture tube of the TV with a soft cloth. Before cleaning the picture tube, disconnect the power cord.
POSSIBLE REMEDY Try a new channel, if OK, then possible station trouble.
Is TV plugged in? Power at outlet? Is TVs POWER button on? Is antenna connected to terminal on the back of the set? If outside antenna is being used, check for broken wire. Check for local interference. Turn off with POWER button and then turn it on after about a minute. Adjust COLOR control. Adjust CONTRAST & BRIGHT control. Check batteries in Remote Control. Move the TV away from the nearby appliances which have Magnetism. Turn off using the POWER button, then turn it on again 30 minutes or so later.

SPECIFICATIONS

GENERAL SPECIFICATIONS
Television system: Closed Caption System: Channel coverage VHF: UHF: CATV: Tuning System Channel access: Terminals Antenna input: Video input: Audio input: Head phone Stereo Sound System 2 speakers NTSC-M TV Standard 15.119/FCC 2 ~ ~ ~ 13, A ~ W, W+1 ~ W+84, A-5 ~ A-1, 5A 181 channel frequency synthesized tuning system Direct access keyboard, programmable scan and up/down VHF/UHF/CATV 75 ohm unbalanced (F-type) RCA connector x 1 RCA connector x 2 (L+R) 1/8 stereo (3.5mm)
ELECTRICAL SPECIFICATIONS
Sound output: 1W, 8 ohmx2

OTHER SPECIFICATIONS

Remote control: Operating temperature: Digital encoded infrared light system

Closed Caption Problem

Possible Remedy
My TV is showing captions that are misspelled.
You are watching a live broadcast and spelling errors made by the closed captioning production company may pass through uncorrected. A prerecorded program will not show any misspelled words because of the normal time available for editing the captions.
My TV will not show the text in its entirety Captions that are delayed a few seconds behind the actual dialogue or there is a delay of what is being said. are common for live broadcasts. Most captioning production companies can display a dialogue to a maximum of 220 words per minute. If a dialogue exceeds that rate, selective editing is used to insure that the captions remain up-to-date with the current TV screen dialogue. My captions are scrambled with white boxes on the TV screen. My program guide listed a TV show as being closed captioned but none of the captions were displayed. My prerecorded videotape does not show any captions. The tape box mentions it being closed captioned. Interference caused by building, power lines, thunderstorms, etc. may cause scrambled or incomplete captions to appear. Broadcasters may at times use a time compression process to the actual program so that additional advertising time can be given. Since the decoder cannot read the compressed information, captions will be lost. The videotape was either an illegal copying or the tape duplicating company accidentally left out the captioning signals during the copying process.
5C to 40C (41F~104F) Power requirements: AC120V, 60Hz Power consumption (Maximum): 73W Picture tube: 19 Dimensions: H : 16-7/8" (428mm) W: 18-11/16" (475mm) D : 17-7/8" (454mm) Weight: 41.9 lbs. (19kg) Designs and specifications are subject to change without notice. If there is a discrepancy between languages, the default language will be English.
My TV screen shows a black box on certain You are in the TEXT mode. Select CAPTION mode or CAPTION channels. [OFF].
As an ENERGY STAR Partner, our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark.
L6406UGES.QX33 03.4.25 11:59 AM Page 1