Key Features

The switch provides the following key features: Compatible with IEEE 802.11n, 802.11g/b wireless standards. Provides three 802.11n/g/b wireless Reverse SMA detachable antennas High speed transfer data rate up to 300Mbps Supports wireless data encryption with 64/128-bit WEP, WPA and WPA2 Supports authentication for wireless connectivity based on ESSID Supports Multiple BSSID. Provides MAC access control and hidden SSID function WDS supported with WEP, TKIP and AES encryption Channel: USA 11, Europe 13 Supports NAT IP Sharing Supports WAN connection type-Static IP, PPPoE, PPTP, & DHCP client SPI Anti-DoS Firewall; Virtual DMZ; DNS relay; UPnP Provides DHCP server and client Supports ALG for FTP, NetMeeting, DDNS (DynDNS, TZO) Supports QoS:WMM Supports firmware upgrade function via Web Supports system log Certifications: FCC Class B, CE Mark, VCCI Class B

The Front Panel

The front panel of the Wireless Router:
LED Definitions Status LED The LED will be dark for a few seconds when the system is started. After that, the LED will blink periodically to show the Wireless Router is working normally. If the LED stays green/dark that means the system failed, you need to contact your agent or try to reboot the system. WLAN LED I. When Wireless AP is ready for data transmitting and receiving, it is steady green. II. When the data is transmitting or receiving, it is blinking green. LAN LEDs Every port has an Act/Link LED. Steady green (link state) indicates that the port has good linkage to its associated devices. Flashing green indicates that the port is receiving or transmitting data between its associated devices. WAN LED The LED stays light (green) means the WAN port has good linkage to its associated devices. The LED will blink green when there is traffic transverse the port. Setup Button We provide this setup button to help users connecting this router to Internet quickly.

The Rear Panel

The rear panel of the Wireless Router is shown below.
Power Connection Plug the circle end of the power adapter firmly into the rear panel of the Wireless Router, and the other end put into an electric service outlet then the system is ready.

Restore Default Button 1. Push the button for more than 5 seconds and then release it, the system will return to factory default setting. In the meantime, system rewrites flash to default value and Status LED halts for a while. Approximately 60 seconds later, the Status LED blinks green periodically, now the whole system parameters have returned to factory default value. If the process has been interrupted by any reason (power off), the system will fail. Before performing the process, ensure a safe operating environment please! To reboot the Router, press the button for 2-5 seconds and then release it, and all the setting wont be erased. Wait for the Router to complete the reboot, and then you can start to use it. WarningIncomplete factory setting recovery procedure will cause the Wireless Router malfunctionIf you are unfortunately in this situation, do not try to repair it by yourself. Consult your local distributor for help!
Installing And Using Wireless Router
This Chapter provides a step-by-step guide to the installation and configuration of the Wireless Router. We suggest you go over the whole chapter and then do more advanced operation.
Network configuration setup
Steps to build up the network: Connect the ADSL or Cable modem to the Ethernet WAN port on the back of the Wireless Router by using the UTP cable. Connect the phone line from the wall socket to the line-in port on the ADSL modem, or the coaxial cable to the line-in port on the Cable modem. Plug-in the power adapter to the modem and turn on the power. Install the Ethernet card into the computer by referring to the User Guide that came with the card. Connect the computer to the Wireless Router by using standard twisted-pair Ethernet cable from the computers Ethernet card to an 10/100Mbps Ethernet port on the back of the Wireless Router. Plug-in the power adapter to the Router and the other side to the wall outlet.
Computer configuration setup
In order to communicate with this Wireless Router, you have to configure the IP addresses of your computer to be compatible with the device. The router supports DHCP server and it is enabled as default. Users that configure your IP address as Obtain an IP address automatically may skip the following IP configuration instruction. Note: 1. The default network setting of the device: IP address: Subnet Mask: DHCP Server: 192.168.1.1 255.255.255.0 enabled

Static IP Mode

Items Information IP Address, Subnet Mask and Fill in the IP address, Subnet Mask and Default Gateway that provided by your Default Gateway Internet Service Provider (ISP). nd To specify the Domain Name Server (DNS). Primary and 2 DNS server Enter the DNS provided by your ISP in 1st and 2nd server. To enable the Maximum Transmission Unit Static IP MTU of Router setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter the MTU number in the blank to set the limitation (default 1500bytes). Name of this device. Host Name Mark the check box to enable others Ping from WAN detecting this device from WAN, and clear the checkbox to disable. Select to use the following MAC as the WAN Ethernet MAC MAC while serving Internet: Original MAC: the MAC of the device. Manual Settings: the MAC of your computer. Click on the words in the bracket to clone your computer MAC in the blank. You can also change the MAC numbers if you need.
* Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations.

DHCP Client Mode

Items Set DNS server
Information If your DNS provide by ISP is dynamic, choose Automatically, if not choose Manually and enter the DNS provided by your ISP in DNS 1, 2. To enable the Maximum Transmission Unit of Router DHCP MTU setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter your MTU number in the text-box to set the limitation (default 1500bytes). Name of this device. Host Name Mark the check box to enable others detecting this Ping from WAN device from WAN, and clear the checkbox to disable. WAN Ethernet MAC Select to use the following MAC as the MAC while serving Internet: Original MAC: the MAC of the device. Manual Settings: the MAC of your computer. Click on the words in the bracket to clone your computer MAC in the blank. You can also change the MAC numbers if you need.

PPPoE Mode

Items Information PPPoE Username and Fill in the User Name and Password that provided by your ISP. The default username/password is Password USERNAME/PASSWORD. If your DNS provide by ISP is dynamic, choose Set DNS server Automatically, if not, choose Manually and enter the DNS provided by your ISP in DNS 1, 2. To enable the Maximum Transmission Unit of PPPoE MTU Router setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter your MTU number in the text-box to set the limitation (default 1492 bytes). Name of this device. Host Name Mark the check box to enable others detecting this Ping form WAN device from WAN, and clear the checkbox to disable. Select to use the following MAC as the MAC while WAN Ethernet MAC serving Internet: Original MAC: the MAC of the device. Manual Settings: the MAC of your computer. Click on the words in the bracket to clone your computer MAC in the blank. You can also change the MAC numbers if you need.

LAN Interface Setup To set up the configuration of LAN interface, private IP of you router LAN port and subnet mask for your LAN segment.

Router Settings

Items IP address Subnet Mask DNS Proxy Information The IP of your Router LAN port (default 192.168.1.1). Subnet Mask of you LAN (default 255.255.255.0). DNS proxy takes DNS queries from the local network and forwards them to an Internet DNS. Mark the check box to enable DNS Proxy function or clear to disable.

DHCP Server Settings

Items Information Enable DHCP Server To give your LAN Client an IP, you have to enable DHCP server. If not, manual setting up your client IP is necessary when you want to use the router as your clients default gateway. Specify the DHCP Client IP address range default DHCP IP Range (100~150). The time for the device to recycle and give out DHCP IP DHCP Lease Time (default 86400).
DHCP Server Settings The information of type, hostname, MAC, IP, description and expire time of the DHCP clients that have connected with this device.
QoS Settings The QoS (Quality of Service) Settings page provides different priority to different users or data flows.
Total Bandwidth Settings You can setup the total upload/ download bandwidth manually (default 102400). Bandwidth QoS Settings Items Enable this Rule Type LAN IP Address Priority Bandwidth Comment Action Information Mark to enable the configuration, and clear to disable. Select the type of download or upload. Fill in the MAC address that you are going to control. Select the transmission priority of low, medium, high, or highest. Fill in the minimum and maximum bandwidth. Give a definition to the LAN IP Address. After configuring the above settings, click Add to add a new list in the following MAC Access Control List. The Change button can be used to change the configuration.
Bandwidth QoS Settings Lists the Bandwidth QoS Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list.

Wireless Settings

Basic Settings You can set up the configuration of your Wireless and monitor the Wireless Clients associate with your AP.

Items Enable Wireless

Information Mark the checkbox to enable Wireless interface or uncheck to disable. To select a band for this device to match 802.11g/b/n Wireless Mode mixed, 802.11g/b mixed, 802.11b, 802.11g, or 802.11n. Select the region you live. Country Wireless Channel Select a channel for the wireless network of this device. Service set identifier for the name of the wireless SSID network.

Advanced Settings You can set advanced wireless LAN parameters of this router. We recommend not changing these parameters unless you know what changes will be there on this router.
General Wireless Advance Settings Items Hide SSID Information Mark to disable SSID from broadcasting. As default, this device broadcasts its SSID to allow every wireless station located within the coverage of this wireless router to discover this wireless router easily. The period of time a beacon is broadcasted (default Beacon Period 100ms). The beacon of a Delivery Traffic Indication Message DTIM Period is broadcasted (default 1 beacon). If the packet size is smaller than the Request To RTS Threshold Send threshold, the wireless router will not send this packet by using the RTS/CTS mechanism (default 2347 bytes). Fragment Threshold Specifies the maximum size of packet during the data transition. A higher value brings a better performance (default 2346 bytes) Select the Transmission Power of very weak, weak, Tx Power medium, and strong according to your demand. Allows the adapters search for 802.11g/b singles g/b Protection only. Select Auto to turns it on or off automatically, select Always On to support protection or select Always Off to disable this function. To enable/disable Wi-Fi Multimedia function. Support WMM
802.11n Wireless advance Settings Items HT Operation Mode Information Select the mixed or green field mode as the Hyper Throughput operation mode. Select the 40MHz or 20MHz as the channel HT Channel Bandwidth bandwidth. Select 400ns or 800ns as the interval time. HT Guard Interval Enable HT TX Aggregate Mark to enable Hyper Throughput TX Aggregate MAC Service Data Unit, and clear to disable. MSDU
Security Settings The Security function protects your wireless network from invasion. We provide WEP and WPA encryption to secure your wireless network. As default, the authentication is configured as safe mode. Please select None/WEP/WPA (Personal) in the drop list. If you select none, any data will be transmitted without encryption and any station can access the router.

WEP Configuration

Items Authentication
Default Key ID WEP Key 1, 2, 3 and 4
Information Open: Wireless AP can associate with this wireless router without WEP encryption. Shared Key: Wireless AP can associate with this wireless router only with WEP encryption. Select to use the WEP key value of 1,2,3 or 4 as in the following settings. Select ASCII or Hex to setup the key value (default 012345).

WPA Configuration

Items WPA Mode
Information Select the option in the drop list to enable modes of auto, WPA only, or WPA2 only. Select TKIP / AES, TKIP or AES as WPA WPA Encryption encryption. Select the key format of Pass Phrase or Pre-Shared Key Hex. Enter the Pre-Shared Key according to the key format you select (default 01234567). To enable/disable WPA rekey method by WPA ReKey Method time or by packet. Enter the numbers to setup the WPA WPA ReKey Interval rekey interval. Pairwise Master Key Cache Select 1, 5, 10, 20, 30, 60, or 120 minuets as the cache interval time. Interval this checkbox to enable Pre-Authentication Support Mark pre-authentication function, and clear to disable.
Access Control To restrict the Number of Access authentication of Stations, set up the control list in this page. You may select Allow Listed to allow those allowed MAC addresses or select Deny Listed to ban those MAC addresses from accessing to this device.
MAC Access Control Settings Items Enable this Rule MAC Address Description Action Information Mark to enable the configuration, and clear to disable. Fill in the MAC address that you are going to control. Give a definition to the MAC Address. After configuring the above settings, click Add to add a new list in the following MAC Access Control List. The Change button can be used to change the configuration.
MAC Access Control List Lists the MAC Access Control Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. Current Associated Client List Lists the current associated client connected to this device. Click on the list to add it into the MAC Access Control List then to do more configurations on it.
WDS Settings Wireless Distribution System allows the router to communicate with other APs wirelessly. To make it work, you must ensure that these APs and the Router are in the same Channel and add these APs MAC Address and Comment values into the WDS list.

AP+WDS (AP Repeater)

WDS (AP Bridge)

Auto (AP Bridge)

Items WDS
Information Select the option in the drop list to enable AP+WDS (AP Repeater), WDS (AP Bridge) or Auto (AP Bridge) as WDS format. Encryption Type Select the option in the drop list to enable WEP, WPA/TKIP, and WPA/AES encryption types. If you select None, any data will be transmitted without encryption and any station can access the router. WPA Encryption For encryption type of WPA/TKIP and WPA/AES, you have to fill in the WPA encryption key. Please use Key Pass Phrase (8~32bytes) key format. For encryption type of WPA/TKIP and WPA/AES, you WDS AP MAC have to fill in the WDS AP MAC. You can fill up to 4 List sets of WDS AP MAC lists.

WPS Settings

WPS Connection Settings Items WPS Config Method Information PIN method (Personal Identification Number): read the PIN from either a sticker on the new STA or a display. PBC method (Push Button Communication): in which the user simply has to push a button, either an actual or virtual one, on both the AP and the new STA. Fill in the PIN code to enrollee device. Click on Build WPS Connection button to execute.

Add Enrollee PIN Code

WPS Information Shows the information of WPA configured, status, SSID, authentication mode, and pre-shared key. Click on Refresh button to refresh the information.

NAT Settings

NAT Settings NAT (Network Address Translation) involves re-writing the source and/or destination addresses of IP packets as they pass through a Router or firewall. NAT enable multiple hosts on a private network to access the Internet using a single public IP address.
NAT & ALG Settings Click on the checkbox to enable NAT function, IPSec (IP Security), PPTP (point-to-point tunneling protocol), and L2TP (layer 2 tunneling protocol) pass through on Virtual Private Network (VPN), or clear to disable. Fill in the port number in the Non-standard FTP port blank if you need. ALG Settings Click on the checkbox to enable SIP (session initiation protocol), NetMeeting, Window Messenger File Transfer, and StarCraft/Battle.net ALG.
Virtual Server After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page.
Virtual Server Settings Items Enable this Rule Application Select WAN Port Protocol LAN Server IP LAN Port Action Information Mark to enable the configuration, and clear to disable. Select an application for your demand. Fill in the port number of WAN. Select the protocol type of TCP, UDP or Both Fill in the IP of your LAN Server. Fill in the port number of LAN. After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration.

Virtual Server Mapping List Lists the Virtual Server Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list.
Virtual DMZ The virtual DMZ (Demilitarized Zone) is used to enable protocols, which need to open ports on the router. The router will forward all unspecified incoming traffic to the host specified in this page. To configure it, mark to enable and then enter the Host IP (private IP address) and click Save Settings to enact the setting.

Firewall Settings

IP Filter
The Wireless Router could filter the outgoing packets for security or management consideration. You can set up the filter against the IP addresses to block specific internal users from accessing the Internet. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page.
IP Filter Settings Items Enable this Rule IP Address Protocol Filter Mode Date Define Time Define Action Information Mark to enable the configuration, and clear to disable. Fill in the IP address that you are going to filter. Select the protocol type of TCP, UDP or Both Select the filter mode of Always or by Schedule For filter mode of by Schedule, you have to define the filter date and time. After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration.
IP Filter Rule List Lists the IP Filter Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list.
Port Filter The firewall could not only obstruct outside intruders from intruding your system, but also restricting the LAN users. Port filtering restricts certain type of data packets from your LAN to Internet through the router. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page.
Port Filter Settings Items Information Enable this Rule Mark to enable the configuration, and clear to disable. Fill in the port range that you are going to filter. The Port Range valid numbers are 1~65535. Select the protocol type of TCP, UDP or Both Protocol Select the filter mode of Always or by Schedule Filter Mode For filter mode of by Schedule, you have to define the Date Define filter date and time. Time Define After configure the above settings, click Add to add a Action new list in the following IP Filter Rule List. The Change button can be used to change the configuration.
Port Filter Rule List Lists the Port Filter Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list.

MAC Filter The Wireless Router could filter the outgoing packets for security or management consideration. You can set up the filter against the MAC addresses to block specific internal users from accessing the Internet. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page.
MAC Filter Settings Items Enable this Rule MAC Address Filter Mode Date Define Time Define Action Information Mark to enable the configuration, and clear to disable. Fill in the MAC address that you are going to filter. Select the filter mode of Always or by Schedule For filter mode of by Schedule, you have to define the filter date and time. After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration.
MAC Filter Rule List Lists the MAC Filter Settings you have added before. Click on the list to change
configuration, or the Delete button to delete the list. Website Filter
The Website Filter allows users to prevent certain website from accessing by users in LAN. This filter will block those websites that contain certain keywords. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page.
Website Filter Settings Items Enable this Rule IP Address Website or Key Word Action Information Mark to enable the configuration, and clear to disable. Fill in the local IP address that you want to restrain it from serving the filtering websites. Fill in the name or keywords of the website to block. After configure the above settings, click Add to add a new list in the following Website Filter Rule List. The Change button can be used to change the configuration.
Website Filter Rule List Lists the Website Filter Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list.

Services Settings

DDNS Settings
DDNS (Dynamic Domain Name Server) service allows users to connect to this device via a fixed and easy-toremember hostname.
Items Enable DDNS Service Provider

Domain Name User Name/Email
Password/Key Confirmed Password
Information Mark to enable the configuration, and clear to disable. The website that provides DDNS service. Please select DynDns.org, No-IP.com or TZO from the drop list. The hostname that you have applied for the device. DDNS login account. For DynDNS users, please fill in your user name; for No-IP and TZO users, please fill in your email address (default USER). The password of your DDNS service account (default PASSWORD). Retype the password to confirm.

UPnP Settings

The UPnP (Universal Plug and Play) service allows devices to connect seamlessly and to simplify the implementation of networks in the home (data sharing, communications, and entertainment) and corporate environments. This page allows user to monitor the information of UPnP clients. Mark or clear the checkbox to enable or disable UPnP IGD, and then click Save Settings to enact your settings.

System Log Settings

The System Log Settings page shows the information of the current activities on the router.

Items System Log

Information Mark to enable the configuration, and clear to disable. Select cleanup when reboot or save Log Type log message as the log type. Select the log message size of 4, 8, or 32 Log Message Size Kbytes. Mark to enable the following Remote Log configuration, and clear to disable. Remote Log Server Address Fill in the sever address for remote log. Fill in the sever port for remote log. Remote Log Server Port To enable/disable log to remote and local Log to Remote and Local

Date/Time Settings

This page allows users to configure the date and time of the router. To specify manually, select the date and time from the drop list and click the Save Settings button. To synchronize time from a timeserver, please enter the update interval hour numbers, select an NTP server from the drop list or manually enter a private NTP server and then click the Save Settings button.
Mark the Daylight Saving checkbox if you want to apply it on system time.

Manual Time Setting

NTP Time Server

Management

Admin Account The admin account is the account for accessing this configuration interface. In this page, you can reset the password of the admin account and setup a designated IP to remote control this device.

Remote Administration Items Remote Control Information Mark this checkbox to allow remote PC accessing the configuration interface of this router. HTTP port for remote The HTTP port for accessing this management interface (default 8080). The permitted IP for accessing. The default IP Remote Control IP 0.0.0.0 allows all IP addresses form accessing. Click on this button to update your setting. Update button Admin Accounts Items Access Level Password Confirm Password Action Information Select an access level of admin or guest. The new password for the admin account Fill in the new password again Click Change button to apply the new password.

Ping Test

The Ping Test page allows the administrator to test the connecting status of Internet. Fill in the IP then click on the Ping Test button to view the result information.

Config

The Config page allows users to backup and download the configuration status of the device or restore the factory default configuration.
Items Save Settings to File Load Settings from File
Reset Settings to Default
Information Click on the Save button to save settings. Click Browse to select the file and then click Reload to start the process. Please wait for it to complete. Click Reset to Default to start the process and it will be completed till the status LED starts blinking.
Firmware Upgrade Sometimes a new firmware may be issued to upgrade the system of this device. You could upgrade the firmware you got in this page. To upgrade the firmware, please click on the Browse button, locate the firmware in your computer and then click the Upload button to execute.

Information

System Information This information page shows the current settings of this device. You could check if the parameters match your configuration.
Packet Statistics This page allows users to get information of data transferring condition, and monitor the status and performance of this router including interface, receiving/sending packets, and receiving/sending errors.
Routing Table This page shows the routing table in this router. Users can get connecting information including destination, gateway, net mask, flags, metric, ref, use and interface.
System Log This page shows the system log information. Click the Refresh button to refresh the list.

Logout

Logout Click the Logout button to log out the admin account from this system
Reboot Click the reboot button to restart this system. This may cost 1 minute to restart the system. Please wait upon restarting.

Product Specifications

Standard
Interface WAN Connection Cable Connections Transmission Mode LED indications Security Receiver Sensitivity Transmit Power Range Coverage Emission Operating Temperature Operating Humidity Power Supply

IEEE 802.11n IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u LAN: 4 port 10/100Mbps Ethernet, RJ-45 WAN: One RJ45 port 3* 802.11n/g/b wireless reverse SMA detachable antenna Ethernet 10/100 Mbps RJ-45 (10BASE-T): Category 3,4,5 UTP RJ-45 (100BASE-TX): Category 5 UTP Auto-Negotiation (Full-duplex, Half-duplex) 1*Power, 1*WAN, 4*LAN, 1*WLAN 64/128-bit WEP, WPA, WPA2 11Mbps-91dBm, 54Mbps-78dBm, 300mbps -69dBm 11Mbps 19dBm, 54Mbps 16dBm, 11n 20MHz and 11n 40MHz 16dBm Indoor 35~100 meters Outdoor 100~300meters. FCC CLASS B, CE 00 ~ 400C (320 ~ 1040F) 10% - 90% RH non-condensing External Power Adapter, 12VDC/ 1A

Wireless IEEE 802.11g 54Mbps Four Port LAN Router

ENHWI-G3

Product Description The Encore ENHWI-G3 Wireless-G Router offers a simple, secure method to add wireless to your network at a great value. It delivers a wireless speed up to 54Mbps, which is almost five times faster than 802.11b standard. ENHWI-G3 is backward compatible with 802.11b standard. In addition, ENHWI-G3 features 4 Fast Ethernet (10/100Mbps) ports to support a wired network. For your protection and convenience, ENHWI-G3 comes with strong security features and user-friendly configuration utility. The ENHWI-G3 is an ideal router for your small office or home. Use this router to surf the Internet, play online games or share office resources. You can achieve significant cost reduction by sharing just one Internet connection among several computers. Getting amazing multimedia applications across your local area network is easier than ever with Encore Wireless-G Router. The ENHWI-G3 is an essential component for your high-speed wired and wireless network. This router features a built-in firewall and WPA and WEP encryption to prevent hacking and intrusion. In addition, ENHWI-G3 supports virtual server and virtual pc mapping for extra protection. You can easily configure and install ENHWI-G3 using the web-based configuration utility.

Product Features

Provide Ethernet to Wireless LAN bridge fully compatible on Ethernet side and fully IEEE 802.3 compatible on the Ethernet side and fully interoperable with IEEE 802.11b & IEEE 802.11g compliant equipment 4 x 10/100Mbps Fast Ethernet port for LAN with Auto MDI-X function 1 x 10/100Mbps WAN port for ADSL / Cable Modem with Auto MDI-X function IEEE 802.11b/g Infrastructure operating modes Dynamic data rate scaling at 11, 5.5, 2 and 1Mbps for 802.11b mode Dynamic data rate scaling at 54, 48, 36, 24, 18, 12 and 6Mbps for 802.11g mode Allow auto fallback data rate for optimized reliability, throughput and transmission range Supports wireless data encryption with 64/128-bit WEP standard for security Supports enhance security for WPA-PSK, WPA2-PSK, WPA and WPA2 Web-based configuration tools and management via WEB Browser Supports PPPoE/PPTP/L2TP protocol for ADSL Supports NAT for share 1 IP address to all LAN user Supports DHCP Server / Client Supports Firewall protection, Virtual server mapping, Special application seeting Supports UPnP Supports statistics information

Product Specifications

Standards

IEEE 802.11b Wireless LAN IEEE 802.11g Wireless LAN IEEE 802.3/IEEE 802.3u Fast Ethernet ANSI/IEEE 802.3 Auto negotiation

Network Management

Web base configuration utility via Ethernet

Channel

USA: Channel 1 ~ 11 Europe: Channel 1 ~ 13 Japan: Channel 1 ~ 14

Radio Technology

Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division Multiplexing (OFDM)

Security

64/128-bits WEP Encryption WPA, WPA2 WPA-PSK, WPA2-PSK MAC address filtering Protocol filtering Domain filtering

Transmission Rate

802.11b: 1, 2, 5.5, 11Mbps (auto sense) 802.11g: 6, 12, 24, 36, 48,54Mbps (auto sense)

Receiver Sensitivity

54Mbps: Typical -70 @ 10% PER (Packet Error Rate) 11Mbps: Typical -85 @ 8% PER (Packet Error Rate)

Range Coverage

Indoor: Up to 30 meters (depends on environment) Outdoor: Up to 100 meters (depends on environment)
Wireless LAN Frequency Range
2412 ~ 2484 MHz ISM band (channels 1 ~ 14)

Modulation Schemes

DBPSK/DQPSK/CCK/OFDM

Diagnostic LEDs

Power, System WAN: Link.ACT LAN: Link/ACT WLAN: ACT

Media Access Protocol

CSMA/CA with ACK

Transmit Power

802.11b: 152dBm typically 802.11g: 132dBm typically

Power Adapter

7.5V / 1A

Antenna Type

Dual diversity antennas with one internal printed antenna and one external 2 dB Gain dipole antenna

Operation Temperature

0 ~ 40 C

Protocol

TCP/IP

Storage Temperature

-10 ~ 70 C

Interface

LAN: 4 x 10/100Mbps Auto-MDIX Ethernet ports WAN: 1 x 10/100Mbps Auto-MDIX Ethernet port

Humidity

10% ~ 95% RH, no condensation

Certifications

FCC Part 15.247 for US ETS for Europe
Supported Network Protocols
TCP/IP NAT PPPoE/PPTP/L2TP HTTP DHCP Server/Client

Dimensions (W x H x D)

147 x 115 x 35 mm (without antenna)