16 Copying

Paper Size
Use this button to select the size of paper youve loaded. Choose one of these sizes: A4, LTR (letter), 4 6, 5 7, or 8 10.
Note: If printing photos, do not use paper with with micro perforated edges. Instead, select one of the papers listed on pages 12 and 13.

Reduce or Enlarge

Use this button to reduce or enlarge the size of your copied image. You can select from these settings:
Setting Actual Auto Fit Page Letter ! ! Letter Letter ! ! Letter A4 ! Letter Letter ! A4 Result Prints the image at its original size

Reduce/enlarge

Reduces or enlarges the image, as needed, to fit the selected paper size Converts the original document size to the finished copy size
To reduce or enlarge by a specific percentage, see Manual Zoom on page 19.
Note: If you select Auto Fit Page to copy a document with white or very light colored edges, the original size may not be recognized correctly, creating an incorrect copy size. If this occurs, use the manual zoom to adjust the size of your copy (see page 19).
Changing Copy Settings 17

Copy Layout

If you want to make copies with a special layout (for example, borderless copies or several copies on one sheet), use the Copy Layout menu. To select a special layout: 1. Press the Menu button. 2. Press the green button next to the LCD screen until you see Copy Layout displayed, then press OK. 3. Continue pressing the green button until you see the desired layout setting, then press OK. Here are the layout settings you can choose from:
Copy Layout Standard Copies your original with a normal margin (0.12 inch or 3 mm) Results
BorderFreeTM Sizes your original as necessary to fit to the edges of 4 x 6, 5 x 7, or 8 x 10 paper* Min Margins Copies your original with a 0.06-inch (1.5 mm) border around the edges*
Repeat Prints an image multiple times on one sheet; select 4, 9, or 16 images per sheet, or Auto to print your image as many times as it will fit (prints full-size; works best with small images)

18 Copying

Copy Layout Poster Prints the original image on separate sheets (4, 9, or 16) that you can paste together to make a large poster

Results

2-up Copies two originals onto one sheet
4-up Copies four originals onto one sheet
If print quality declines at the bottom of the page, use the Standard layout setting.

Copy Density

To make your copies lighter or darker, use the Copy Density menu: 1. Press the Menu button. 2. Press the green button next to the LCD screen until you see Copy Density displayed, then press OK. 3. Press the green buttons (next to - and +) to lighten or darken your copies, then press OK.

Manual Zoom

You can manually adjust the size of your copies from 25% to 400%: 1. Press the Menu button. 2. Press the green button next to the LCD screen until you see Optional Zoom displayed, then press OK. 3. Use the number keypad to enter the size percentage, then press OK.

Changing Copy Settings 19

Using Memory Cards

This chapter tells you what kinds of memory cards to use with your CX6400, and how to insert them. See these sections:
Compatible Memory Cards (below) Inserting a Card on page 21 Using Your CX6400 as a Card Reader on page 22
See also Printing from a Card on page 25 and Scanning to a Card on page 32.

Compatible Memory Cards

You can use the following types of cards with your CX6400:
Slot A Type of card Memory Stick MagicGate Memory Stick Memory Stick PRO SD Card MultiMediaCard Memory Stick Duo (adapter required) miniSD Card (adapter required) SmartMediaTM xD-Picture Card CompactFlashTM Microdrive

Slot A Slot B

Slot C Memory card light

20 Using Memory Cards

Inserting a Card
1. Make sure the CX6400 is turned on. 2. If you will be printing from or scanning to the card, make sure your CX6400 is not connected to your computer (or your computer is turned off ). If you want to copy images between the card and your computer, leave the computer connected. Any images stored on the card will be automatically copied to your computer once you insert the card (see page 22). 3. Open the memory card cover.
4. Make sure the memory card light (next to the memory card slots) is off and that no cards are in any of the slots. Then insert a card into the correct slot, as shown on page 20.
Note: Do not insert more than one card at a time, or you may not be able to tell which card your images are being read from.

Inserting a Card 21

After the CX6400 reads the card, if it finds any images saved in a compatible format (see note below), you see the following screen:

Found Images. Total XXX

5. Press the button next to OK (shown on the screen). To remove the card, pull it straight out of its slot. On a Macintosh, drag the card icon on your desktop to the Trash icon before removing the card.
Caution: Do not remove the card or turn off the CX6400 while the memory card light is flashing, or you may lose data on the card. Note: Your image files must meet these requirements: File format Media format Image size JPEG or TIF format image files (supports Exif version 2.1/2.2) DCF (Design rule for Camera File system) version 1.0 Vertical 120 to 4600 pixels, horizontal 120 to 4600 pixels
Using Your CX6400 as a Card Reader
You can use your CX6400 as an external card reader, letting you copy images from a card to your computer, or vice versa. To use this feature with Windows 98 or Me, make sure youve already installed your CX6400 software as described on the Start Here sheet (this automatically installs the necessary USB storage driver). 1. Make sure your CX6400 is turned on and connected to your computer. 2. Insert a memory card as described in the previous section. (If youll be copying images to the card, make sure the cards write-protect tab, if it has one, is set to allow writing on the card.)

Note: If this is your first time inserting a card, see Using EPSON CardMonitor on page 23 to set up EPSON CardMonitor.

22 Using Memory Cards

3. Once the card is inserted, it appears as a removable drive icon on your computer. Copy images to or from the card, as needed.
Note: If you copy images to the card, the number of images shown on the LCD screen does not automatically change. You must remove and reinsert the card to make the CX6400 recognize the new images.

Using EPSON CardMonitor

You can use EPSON CardMonitor to copy images automatically to your computer whenever you insert a card. You can also pick an application to automatically open and help you edit your pictures. Follow the instructions below for your operating system.

Windows

1. If your computer (Windows XP or 2000) asks you what you want to do when you insert a card, select Startup CardMonitor, click the checkbox for Always do the selected action, and click OK. 2. If this is your first time inserting a card, you see this screen:
Click Next. 3. The EPSON PhotoStarter setup assistant opens. Follow the instructions on the screen to set up EPSON CardMonitor.
Using Your CX6400 as a Card Reader 23

Macintosh

1. Open the Applications folder on your hard drive, then double-click ImageCapture. You see this screen:
2. From the Image Capture menu, select Preferences. You see this screen:

Select Other

3. From the Camera Preferences drop-down list, select Other. A new Applications folder opens. 4. Open the EPSON CardMonitor folder, then click the EPSON CardMonitor icon. 5. Click the Open button. 6. Close the Image Capture utility. 7. CardMonitor will now open automatically when you insert a card. Follow the instructions on the screen to set up CardMonitor to copy images to your computer when you insert a card and open an image-editing application, if desired.
Note: If CardMonitor doesnt open automatically, browse to the new drive icon on your desktop to view your images.

24 Using Memory Cards

Printing from a Card
The Stylus CX6400 lets you print photos directly from your digital cameras memory cardyou dont even have to connect the CX6400 to a computer. If your memory card contains photos taken with a camera that supports DPOF (Digital Print Order Format), you can pre-select the photos you want to print while the card is still in the camera. See these sections:

Printing an Index Form (below) Selecting Photos to Print on page 26 Printing with DPOF on page 28 Choosing Print Settings on page 29

Printing an Index Form

In most cases, youll want to print an index form before printing any photos from your memory card. An index form lets you see small thumbnail images of the pictures on your card and select just the ones you want to print. 1. Make sure your CX6400 is not connected to your computer (or your computer is turned off ), then insert a memory card (see Inserting a Card on page 21). Once the card is inserted, the CX6400 reads and displays the number of printable images on the card (only images in a compatible JPEG or TIF file format are detected). 2. Press the Card Print button to enter Card Print mode. 3. Press the green button next to the LCD screen until Print Index appears, then press the green OK button.

Print Index

Printing from a Card 25
4. Load several sheets of plain, letter-size paper. (If there are more than 36 images on the card, you will need multiple sheets to print the index.) 5. Press the Color button to print the index. After the index form prints, Scan Index appears on the LCD screen. Leave your memory card in the printer and see the instructions below for printing your photos.
Selecting Photos to Print
You can select the photos you want to print either by filling in the ovals on the index form and scanning it (below), or by selecting a photo or range of photos from the control panel (page 27).
Selecting Photos with the Index Form
1. Once you have printed the index form, fill in the oval beneath each photo you want to print with a dark pen or pencil.

Not OK:

2. Near the bottom of the form, select the type and size of paper you want to use. You can select from these options:
Option Glossy - Glossy - Glossy - Letter DB Photo - DB Photo - Letter Matte - Letter Available paper types EPSON Photo Paper EPSON Glossy Photo Paper EPSON Premium Semigloss Photo Paper EPSON DURABright Ink Glossy Photo Paper EPSON Matte Paper Heavyweight PremierArt Matte Scrapbook Paper for Epson
3. Load the type of paper youve chosen to print on (see Loading Paper on page 11). 26 Printing from a Card
4. Make sure Scan Index appears on the control panel, then press OK. (If it doesnt appear, press the Card Print button, press the green button next to the LCD screen until you see Scan Index, then press OK.) 5. Place the index form face-down on the scanner, so that the top of the form is aligned against the left edge of the glass (see page 31). 6. Press the Color button. The form is scanned and your photos are automatically printed.
Selecting Photos from the Control Panel
1. Once you have printed the index form, identify a photo or range of consecutive photos you want to print. 2. Make sure youre in Card Print mode (if necessary, press the Card Print button). 3. Press the green button next to the LCD screen to select One image, Range of images, or All images, then press OK.

If you have loaded this kind of paper. Plain paper EPSON Bright White Photo Paper EPSON Matte Paper Heavyweight PremierArt Matte Scrapbook Paper for Epson EPSON Photo Paper EPSON Glossy Photo Paper EPSON Premium Semigloss Photo Paper EPSON DURABright Ink Glossy Photo Paper
Use this button to select the size of paper youve loaded. Choose one of these sizes: LTR (letter), 4 6, 5 7, or 8 10. (Some sizes are not available, depending on the selected paper type.)
Choosing Print Settings 29

Layout

Use this button to select one of these layout settings:
Setting B-Free 1-up 2-up 4-up 8-up 20-up 80-up
Results Prints without margins (BorderFree) so that the image covers the whole page. Prints one or more photos per page. For example, 8-up prints up to 8 photos per page. (The actual number may be less, depending on the number of photos or the number of copies youve selected. For example, if you select 5 copies for an 8-up layout, only 5 photos will print on the page. If you select more than 8 copies, you will need additional sheets to print your photos.) The size of each photo is adjusted automatically for the layout and paper size.

Upper1/2

Prints only on the upper half of each page

30 Printing from a Card

Scanning to a Card
Follow the instructions in this chapter to scan your photos and other documents directly to a memory card. See these sections:
Placing Your Original Document (below) Scanning to a Card on page 32
Placing Your Original Document
1. Open the scanner lid. 2. Place your document face-down on the glass, in the upper left corner. Move your document about 1/8 inch from the top and side edge so your entire document is scanned.
Move the document about 1/8 inch in from the edges
3. Close the scanner lid.
Note: If you place your document against the guides, the edges next to the guides wont be scanned. If you need to scan a thick document, such as a book, you can remove the scanner lid to scan. Gently press down the original to keep it flat on the document table. Be sure to replace the scanner lid when youre finished.

Scanning to a Card 31

Follow these steps to scan an image to a memory card and save it in JPEG format: 1. Make sure your CX6400 is not connected to your computer (or your computer is turned off ), then insert a memory card (see page 21).
Note: If the card is not properly formatted, you see a message on the LCD screen. Press the button indicated on the screen to format the card. Any data stored on the card will be erased.

2. Press the Scan button to enter Scan Mode. 3. Press the green button next to the LCD screen until To Photo Card appears, then press OK.
Note: You can also scan to your computer or create an e-mail with the scanned image attached. Select either To PC or To E-mail, then see your online Reference Guide for details.
4. Select the document type (Text or Graphic).

Document type

5. Select Auto as the scan area. (If the edges of your document are light in color, the CX6400 may not be able to detect them and part of your image may be cut off; in that case, select Max. to scan the entire area.) 6. For ordinary documents, select Normal as the quality of the scanned image. For higher quality, select either Fine (for text) or Graphic (for photos).
Note: Higher-quality images take up more memory card space.

Image quality

Scan area
7. Press the button next to OK (shown on the LCD screen).

32 Scanning to a Card

8. Make sure your original document is placed in the scanner, then press the Color button to start scanning. Your image is saved to the epscan folder on the memory card.
9. Wait until scanning finishes and the memory card light goes off, then remove the card.

Scanning to a Card 33

Maintaining Your CX6400
If you notice a decline in print quality, follow the instructions in this chapter to check and clean the print head. Youll also find instructions on checking ink levels and replacing the ink cartridges. See these sections:
Cleaning the Print Head (below) Replacing Ink Cartridges on page 36

Cleaning the Print Head

If your printouts are unexpectedly light or faint, or you notice light or dark bands across your printout, you may need to clean the print head. This unclogs the nozzles so they can deliver ink properly.
Note: Print head cleaning uses ink, so clean it only if quality declines. If you notice that text or straight vertical lines appear jagged, you may need to align the print head. See your online Reference Guide for details.

Running a Nozzle Check

1. Make sure the CX6400 is turned on, paper is loaded, and the red ! error light is off. (If the ! error light is on, check the LCD screen to see if you have to replace an ink cartridge.) 2. Press the Setup button to enter Setup Mode. 3. Press the green button next to the LCD screen until you see Nozzle check displayed, then press the Color button to print the nozzle check.
34 Maintaining Your CX6400
4. After the nozzle check finishes printing, make sure each line is complete, without any gaps or missing dots:
If any dots are missing, as shown below, clean the print head as described in the next section.
Running the Head Cleaning Utility
If you need to clean the print head, follow these steps: 1. Press the Setup button to enter Setup Mode. 2. Press the green button next to the LCD screen until you see Head Cleaning displayed, then press the Color button. The CX6400 runs a head cleaning cycle, and you see the message Head cleaning. on the LCD screen.
Caution: Never turn off the CX6400 while head cleaning is in progress, or you may damage the mechanism.
3. When the message Head cleaning. disappears, repeat the nozzle check (see page 34) to verify that the print head is clean. If you dont see any improvement after cleaning three or four times, turn off the CX6400 and wait overnight. This lets any dried ink soften. Then try cleaning the print head again the next day.
Cleaning the Print Head 35

Replacing Ink Cartridges

To check ink levels, follow these steps: 1. Press the Setup button to enter Setup Mode. 2. Press the green button next to the LCD screen until Ink Levels is displayed, then press the Color button. You see the amount of ink available in each cartridge: C (Cyan), M (Magenta), Y (Yellow), K (Black).
Note: To view all the ink levels, wait for them to scroll across the screen.
Ink levels C:50% M:50% Y:50%
3. When done, press the OK button. When your ink starts getting low, make sure you have replacement cartridges available. You cannot print if an ink cartridge is empty.
Installing New Cartridges
Make sure you have a new ink cartridge before you begin. Use these cartridges:
Color Black Cyan Magenta Yellow * Part number T0441 (standard capacity)* T0431 (high capacity)* T0442 T0443 T0444
Availability of black ink cartridge types varies by location. The high capacity black ink cartridges are recommended as replacement cartridges for this printer for users who print frequently. Users that print infrequently may want to choose the standard capacity black ink cartridge. Your printer includes the high capacity black ink cartridge.

Problems and Solutions

Check the solutions below if youre having trouble using your CX6400 in stand-alone mode.

Copying Problems

Make sure your paper is positioned on the right side of the sheet feeder, behind the feeder guard, then push the left edge guide lightly against the paper. Dont load paper above the arrow on the left edge guide. Make sure your paper is loaded short edge first. Make sure your original is positioned in the top-left corner of the glass, with the short edge at the left (see page 31). Place it approximately 1/8 inch from the edge of the glass to avoid cropping. Make sure you select the copy layout you want. See page 18 for instructions. If you select Auto Fit Page to copy a document with white or very light edges, the original size may not be recognized correctly. Select Actual as the Reduce/Enlarge setting and use the Optional Zoom setting to adjust the size of your copy.

40 Solving Problems

Paper Feeding Problems
If paper doesnt feed, remove it from the sheet feeder. Fan the paper, load it against the right side, behind the feeder guard, and slide the left edge guide against the paper (but not too tightly). If paper jams, follow these steps: 1. Press the On button to turn off the CX6400. 2. Lift up the scanner section and remove any paper thats inside, including any small pieces that may have torn off.
Caution: Clear paper jams by pulling the paper out towards the front of the CX6400. Never pull the paper out in the direction of the sheet feeder.
3. Turn the CX6400 back on and reload the paper. Make sure the edges are not creased or folded.

Copy Quality Problems

If you have any problems with the quality of your copies, try these solutions:
Make sure the document is placed flat against the document table glass. If only part of the image is blurred, your document may be wrinkled or warped. Make sure the CX6400 is not tilted or placed on an uneven surface. Clean the print head; see page 34 for instructions. If a dotted line appears in the image, clean the scanner glass with a soft, dry, lint-free cloth (paper towels are not recommended). If the glass is still not clean, use a small amount of glass cleaner on a soft cloth. Make sure you wipe off any remaining liquid. Dont spray glass cleaner directly on the glass. Make sure your paper isnt damp, curled, or loaded face down (the printable side should be face up). Load new paper face up. Use EPSON papers for proper saturation and absorption of genuine EPSON inks. Use a support sheet with special paper or load your paper one sheet at a time. If you notice jagged vertical lines, you may need to align the print head. See your online CX6400 Reference Guide for instructions. The ink cartridges may be old or low on ink; see page 36 for instructions on replacing an ink cartridge.

Problems and Solutions 41

Where To Get Help

If you need help with your EPSON Stylus CX6400 or EPSON Scan software, see EPSON Support below. If you need help with any other software that came with your CX6400, see Other Software Technical Support on page 43.

EPSON Support

EPSON provides technical assistance 24 hours a day through the electronic support services and automated telephone services listed in the following table:
Service World Wide Web Access From the Internet, you can reach EPSON Support at http://support.epson.com. At this site, you can download drivers and other files, look at product documentation, access troubleshooting information, and receive technical advice through e-mail. A variety of automated help services are available 24 hours a day, seven days a week. To use these services, you must have a touch tone telephone and call (800) 922-8911. Your EPSON SoundAdviceSM Express Code is 70495. Use this code to quickly select the EPSON Stylus CX6400 in SoundAdvice.
Automated Telephone Services
To speak to a technical support representative, dial:
U.S.: (562) 276-4382, 6 AM to 6 PM, Pacific Time, Monday through Friday Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday
Toll or long distance charges may apply.

42 Solving Problems

Before you call, please have the following information ready:
Product name (EPSON Stylus CX6400) Product serial number (located on the back of the unit) Proof of purchase (such as a store receipt) and date of purchase Computer configuration Description of the problem
You can purchase ink cartridges, paper, manuals, and accessories from the EPSON Store at (800) 873-7766 or visit www.epsonstore.com (U.S. sales only). In Canada, please call (800) 463-7766 for dealer referral.
Other Software Technical Support
Software EPSON Smart PanelTM ArcSoft PhotoImpressionTM Telephone (510) 445-8616 Fax (510) 445-8601 Online and E-mail www.newsoftinc.com tech@newsoftinc.com (510) 440-9901 8:30 AM5:30 PM, Pacific Time, Monday through Friday (510) 226-6719 (510) 440-1270 www.arcsoft.com/ techmain support@arcsoft.com

ABBYY FineReader Sprint

(510) 226-6069
www.abbyyusa.com support@abbyyusa.com

Where To Get Help 43

Notices
Important Safety Instructions
Before using your EPSON Stylus CX6400, read and follow these safety instructions:
Be sure to follow all warnings and instructions marked on the Stylus CX6400. Use only the type of power source indicated on the Stylus CX6400 label. Connect all equipment to properly grounded power outlets. Avoid using outlets on the same circuit as air control systems or other high-load devices that regularly switch on and off. Place the Stylus CX6400 near a wall outlet where the plug can be easily unplugged. Placez limprimante prs dune prise de contacte o la fiche peut tre dbranche facilement. Do not let the power cord become damaged or frayed. If you use an extension cord with the Stylus CX6400, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cords ampere rating. Also, make sure the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlets ampere rating. Avoid electrical outlets controlled by wall switches or automatic timers. Keep your Stylus CX6400 and computer system away from potential sources of electromagnetic interference, such as loudspeakers or cordless telephone base units. Avoid locations that are subject to rapid changes in heat or humidity, shocks or vibrations, or dust. Leave enough room around the Stylus CX6400 for sufficient ventilation. Do not place the Stylus CX6400 near a radiator or heating vent or in direct sunlight. Place the Stylus CX6400 on a flat, stable surface that extends beyond its base in all directions. It will not operate properly if it is tilted or at an angle. Leave enough space in front of the Stylus CX6400 (at least 9 inches) so it doesnt tip forward and fall off of the work surface. Turn off and unplug the Stylus CX6400 before cleaning. Clean with a damp cloth only. Do not spill liquid on it. Always turn the Stylus CX6400 off using the On button. Dont turn off the power using a switch on a power strip or unplug the Stylus CX6400 until the On light is off.

44 Notices

Do not block or cover openings in the Stylus CX6400 case or insert objects through the slots. Except as specifically explained in your documentation, do not attempt to service the Stylus CX6400 yourself. Unplug the Stylus CX6400 and refer servicing to qualified service personnel under the following conditions: if the power cord or plug is damaged; if liquid has entered the product; if the product has been dropped or the case damaged; if the product does not operate normally or exhibits a distinct change in performance. Adjust only those controls that are covered by the operating instructions. Before transporting the Stylus CX6400, make sure the print head is capped in the far right position and the ink cartridges are in place. This product includes a lamp component that contains mercury (Hg). Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

46 Notices

to Epson or its authorized service center, where the printer will be fixed and sent back to you. You are responsible for packing the printer and for all costs to and from the Epson authorized service center. When warranty service involves the exchange of the printer or a part, the item replaced becomes Epson property. The replacement printer or part may be new or refurbished to the Epson standard of quality, and, at Epsons option, may be another model of like kind and quality. Epsons liability for replacement of the covered printer will not exceed the original retail selling price of the covered printer. Exchange products and parts assume the remaining warranty period of your original product covered by this limited warranty. What This Warranty Does Not Cover: This warranty does not apply to refurbished or reconditioned products. This warranty covers only normal use in the United States and Canada. This warranty is not transferable. This warranty does not cover any color change or fading of prints or reimbursement of materials or services required for reprinting. This warranty does not cover damage to the EPSON product caused by parts or supplies not manufactured, distributed or certified by Epson. This warranty does not cover ribbons, ink cartridges or third party parts, components, or peripheral devices added to the EPSON product after its shipment from Epson, e.g., dealer or user-added boards or components. Epson is not responsible for warranty service should the Epson label or logo or the rating label or serial number be removed or should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-Epson products, or service other than by an Epson Authorized Servicer. If a claimed defect cannot be identified or reproduced, you will be held responsible for the costs incurred. THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENT OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY. In Canada, warranties include both warranties and conditions. Some jurisdictions do not allow limitations on how long an implied warranty lasts, and some jurisdictions do not allow the exclusion or limitation of incidental or consequential Epson America, Inc. Limited Warranty 47

Declaration of Conformity
According to 47CFR, Part 2 and 15 for: Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers: We: Located at: EPSON AMERICA, INC. MS 3-Kilroy Airport Way Long Beach, CA 90806 Telephone: (562) 290-5254
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Trade Name: EPSON Type of Product: Multifunction printer Model: C161A

ENERGY STAR Compliance

As an ENERGY STAR Partner, EPSON has determined that this product meets the ENERGY STAR guidelines for energy efficiency. The EPA ENERGY STAR office equipment program is a voluntary partnership with the computer and office equipment industry to promote the introduction of energy-efficient personal computers, monitors, printers, fax machines, and copiers in an effort to reduce air pollution caused by power generation.
Declaration of Conformity 49
Printed in XXXXXX XX.XX-XX