CXL-150

Important Notices
READ and UNDERSTAND this owners manual
Both the operator and the adult supervisor should completely read and understand this owners manual before operating this vehicle. This owners manual will instruct you in the safe operation of the vehicle.

NO Passengers

This vehicle was designed for operation ONLY by the operator, (Driver). The load limit and seat configuration is designed for the operator ONLY. It is not safe to carry passengers on the vehicle.
ADULT Supervision and Instruction are REQUIRED.
This vehicle MUST NOT be operated by a youth without adult instructions. E-TON recommends that both the operator and the adult instructor attend an ATV safety instruction course.
ALWAYS Wear Protective Clothing
While operating this vehicle, the driver must always wear protective clothing. Protective helmet with face shield, elbow and knee pads, long leg pants, gloves and hard soled boots should always be worn when operating this vehicle.

OFF ROAD Use ONLY

This vehicle is designed and manufactured for off-road use only. Operation on public streets, roads or highways is illegal and very dangerous.
OBEY all State and local laws and regulations
Each state and local governing agency has laws and regulations for ATV operations. It is the owners responsibility to know, understand and obey these laws and regulations.
Age Recommendations by model size ATV Model Size
Under 70cc 70 - 90cc over 90cc 150 cc

ETON Models

RXL-40E RXL-50M RXL-70 RXL-90 RXL-90R CXL-150 CXL-150

Minimum Age

6 years and older 12 years and older 16 years and older 16 years and older

Weight Capacity

70 Lbs 250 Lbs 250 Lbs 300 Lbs

Page 1

Table of Contents
Safety notes Vehicle identification number location Controls, switches and feature locations Control feature operations Engine stop switch Throttle lever Front & Rear Brakes Parking brake Fuel System Fuel tank Fuel valve Inline Fuel Filter Engine Oil Checking Engine Oil Level Changing Engine Oil Engine Oil Cooler Transmission Shifting Gears Checking Transmission Oil Level Changing Transmission Oil Tires & Wheels Tire inspection Tire pressure Spark Plug Spark Arrester Screen Air Filter Braking Systems Front Brake Inspection Front Brake Adjustment Rear Brake Inspection Filling the Brake Fluid Reservoir Purging Brake Line Drive Chain Throttle Lever Electrical Battery Pre-Operation Inspection Starting procedure Driving Turning Parking Accessories Standard Equipment Optional Equipment Specifications Maintenance Schedule Maintenance Record Chart Wiring Diagram Manufacturers Warranty Owners Notes 27 29

Page 2

Safety Notes
1. Both the adult instructor and youth operator must fully understand everything in this manual before operating this vehicle. 2. This vehicle was designed for the operator only. NO PASSENGERS should be allowed on this vehicle. 3. This vehicle is designed for operation on level, obstacle free off-road areas. 4. Riding this vehicle on public roads or highways is illegal. If it becomes necessary to cross a public road or highway, the vehicle should be pushed across using extreme caution. 5. DO NOT operate this vehicle while under the influence of drugs, alcohol or other medication that impairs judgment or coordination. Doing so can result in serious injury or even death. 6. Maintain a safe distance between your vehicle and other vehicles with whom you are riding. 7. READ the owners manual carefully before riding.
8. ALWAYS wear a helmet, face shield, elbow & knee pads, hard-soled boots, gloves, and protective clothing while operating this vehicle.

Page 3

9. NEVER ride this vehicle unless it has been properly maintained and adjusted. Always perform a pre-ride inspection of your vehicle. Look for wires, bolts and other fasteners that may have come loose on previous rides. Inspect the drive chain, throttle and brakes for proper adjustment and operation. Check the engine oil level in the oil tank. Check fuel level and inspect for fuel leaks. (Remember, you can ride further in one hour than you can walk back in one day!)
10. WARM UP your body with some exercises before riding. This helps to make you alert and prevent cramping and other discomfort.
11. LEARN TO RIDE this vehicle properly and safely. Have an experienced rider teach you the safe operation of your vehicle. E-TON recommends you take an ATV riding course before you first ride your vehicle.

Page 4

12. NEVER REFUEL this vehicle when hot. Ask your adult supervisor to refuel your vehicle. Gasoline is extremely flammable and will ignite if spilled on a hot engine or muffler. Never smoke or expose the fuel to an open flame or spark while refueling your vehicle. Always refuel your vehicle in a safe place free of any ignition source.
13. NEVER run the vehicle in an enclosed area. The exhaust gases from the engine contain CARBON MONOXIDE which can be fatal if breathed in high concentrations for an extended time.
14. HOT! The engine and exhaust system on your vehicle become very hot during normal operation. Touching these hot surfaces can cause severe burns. Always assume that your units engine and exhaust system are HOT unless you know that they are not.

Page 5

Additional safety tips:
Participate in an approved ATV safety education training program. Always provide responsible adult supervision for ATV operators younger than 18 years of age. Never let youths less than 16 years old ride full-sized ATV's. Follow all safety recommendations of the ATV manufacturer. Operate ATVs only during daylight. Wear a helmet with face protection at all times. Operate only four-wheeled ATVs. Provide a drug and alcohol free environment. Always use the buddy system. Avoid riding in areas where contact with automobiles might be possible. Drive ATVs on surfaces as recommended by the manufacturer. Travel at speeds conducive to conditions and operator abilities. Check on the conditions of the trails you will be traveling. Know and understand local and state laws governing the use of ATVs. Permit only one operator per ATV _ NO Passengers. Insist on a "perfect fit" between the ATV and the physical, mental, and emotional maturity of the operator. Use antenna flags and wear bright clothing to increase visibility. Use maps and a compass if you are riding in an unfamiliar area. Make a mental note of landmarks; you may need them if you are stranded. If you are lost at night, do not move around. You will waste valuable fuel that you can use to ride safety in the daylight. Carry a first-aid pack with you. Carry snacks and a water supply with you. Carry equipment to handle medical and mechanical emergencies. Your vehicle field repair kit should include the following items; o the manufacturer's tool kit o wire, tape, elastic cords, o possibly locking pliers o and a tow rope. Pre-Ride Inspection - Inspecting the condition of your ATV before each ride is very important to minimize the chance of injury and maximize the enjoyment of your ride. It also helps to ensure long term performance of your ATV. Follow the owners manual guide to inspection and maintenance of your ATV. A well maintained ATV will give you years of enjoyment. Watch out for thin ice which may be camouflaged by snow. Remember, you can ride further in one hour than you can walk in an entire day.

Age Recommendations by model size ATV Model Size Under 70cc 70 - 90cc over 90cc 150 cc ETON Models RXL-40E RXL-50M RXL-70 RXL-90 RXL-90R CXL-150 CXL-150 Minimum Age 6 years and older 12 years and older 16 years and older 16 years and older Weight Capacity 70 Lbs 250 Lbs 250 Lbs 300 Lbs

Page 6

Vehicle Identification Numbers
Vehicle Identification Number (VIN) is located at the front of the unit under the front fender on a plate mounted between the main frame rails.
Engine serial number is located on the left-hand side of the engine on the crankcase housing.
Your VIN RFZ______________

Eng. No._______________

Controls, Switches & Feature Locations
Locations of controls and features: 1. Rear Brake Lever 2. Headlight Switch 3. Horn Button 4. Engine Stop Switch 5. Front Brake Lever 6. Throttle Lever 7. Fuel Gauge 8. Transmission Gear indicator Lamps 9. Transmission Gear Shift Shaft 10. Starter Button

Page 7

Control Features

Engine Stop Switch

As your operator gains more experience, you can increase the throttle travel to allow for
The stop switch is a red colored rocker switch located on the left-hand handle bar. To start and run the engine, this switch must be placed in the on, O, position. The vehicle is also equipped with a safety brake switch which will prevent the engine from starting until the parking brake is engaged. additional speed to be obtained. To stop your engine, place the switch to the stop, X, position. In the stop, X, position the ignition system is grounded preventing the spark plug from firing. This switch can also be used as a safety or emergency stop switch. To increase the throttles travel, thus increasing the maximum speed, turn the throttle stop bolt counter clockwise. To decrease the throttles travel, thus decreasing the maximum speed, turn the throttle stop bolt clockwise. The throttle cable should be adjusted so there is 2mm, (1/8) free travel at the lever before the throttle starts to open.

Throttle lever

The throttle lever is located on the right-hand handle bar below the grip. To operate the throttle lever, place your right thumb on the

Front and Rear Brakes

This vehicle is equipped with dual front mechanical drum brakes and a rear hydraulic disc brake. The front brakes are controlled by the long brake lever on the right-handle bar. The rear brake is controlled by the long lever on the left-handle bar.
lever and press forward to increase your speed. To decrease your speed, reduce your pressure on the lever and the spring tension will automatically reduce your speed. The travel of the throttle lever is controlled by the throttle stop bolt.

Page 8

The rear brake is the primary stopping brake on your vehicle. Using the rear brake to stop your vehicle will prevent steering control loss.

Fuel Tank

Use your front and rear brakes in combination to control your speed while descending a grade. Use caution not to apply too much pressure to your front brakes so that the wheels lock up, stop turning, and cause a loss of steering control. If the front wheels lock up, and stop turning, lightly reduce the pressure on the front brake lever until they unlock and start to turn.

and press the starter button. Fuel should flow into the container from the fuel line.
ALWAYS CHECK YOUR Fuel level before you start riding your ATV. Remember: You can drive further in one hour on your ATV than you can walk in one day.

Inline Fuel Filter

Page 10

Engine Oil

dusty or humidity is high the engine oil should be change more frequently.

Changing Engine Oil

1. Place an oil catch pan under the unit directly below the engine crankcase. 2. Remove the crankcase drain plug located on the bottom of the crankcase on the underside of the unit. 3. Remove the engine oil dipstick located on the right hand side of the engine below the shifter shaft. 4. Allow the oil to drain completely (1530 min). 5. Reinstall the drain plug and tighten. Torque to 7-10ft-lbs 6. Fill the crankcase with of SAE 30W engine oil through the dip dipstick hole. 1 liter / 1 quart. 7. Reinstall the engine oil dipstick and finger tighten. 8. Dispose of used oil at a proper recycling station as required by law
Your ATV uses automotive type engine oil to lubricate the engine. The engine oil dip stick is located on the right hand side of your engine below the transmission shifting lever. To check your oil level, remove the dip stick by turning the thumb hold counter clockwise until the stick has been completely disengaged from the threads. Pull the dip stick out of the crankcase and check the level of the oil as indicated on the dip stick. The engine oil is full when the oil reaches the level on the stick as indicated in the photo above. Always check your engine oil level with the engine off and cold. Removing the dip stick with the engine running could cause hot oil to splash from the crankcase causing severe burns. Checking your engine oil while the engine is hot can give you a false reading; always check the oil level with a cold engine. Your engine requires SAE 30W engine oil and the crankcase capacity is 1.0 Liters / 1 quart. The engine oil should be changed before the start of each riding season or every 300 hours of operation. When riding where conditions are

Page 11

Oil Cooler

Transmission Shifting

Your ATV is equipped with a fully automatic C.V.T. transmission and has forward and reverse gearing. A transmission shifting shaft is located on the right hand side of your engine.
The engine oil is cooled by pumping the oil through an external oil cooling radiator located at the front of the unit. It is important that the cooling fins of the radiator be kept clean of dirt build up to prevent engine overheating.
The shifter has three positions F Forward, N Neutral and R Reverse.
Remove any build up of mud and dirt from the cooling unit with a pressurized spray of water.
. Inspect the Oil cooler line for leaks and damage. Replace any damaged lines and repair any leaking connections before starting the engine.

The instrument panel has three lights that correspond to the transmission shifter shaft position. The transmission must be placed in the N (neutral Green indicator Lamp) to start the engine.

Page 12

Slowly move the shifting lever to the desired gear pausing slightly at the neutral position. Once you have the gear selected increase the throttle slowly until the transmission becomes fully engaged and the vehicle starts moving in the desired direction. When shifting gears it is important that you bring the vehicle to a complete stop with the rear brake fully engaged and the engine at idle. If you attempt to shift the transmission with the engine running above the idle speed the engine will automatically shut down to protect the transmission. If this should happen you will need to turn off the ignition switch to reset the safety lock out before attempting to restart the engine.

Transmission Oil

Your ATV uses SAE 80/90W gear oil to lubricate the drive and transmission gears.
Changing Transmission Oil
1. Place an oil catch pan under the unit directly below the transmission box. 2. Remove the transmission box drain plug located on the bottom of the transmission box on the underside of the unit. 3. Remove the transmission box fill hole plug locate on top of the transmission box on the right hand side of the engine. 4. Allow the oil to drain completely (1530 min). 5. Reinstall the drain plug and tighten. Torque to 7-10ft-lbs 6. Fill the transmission box with SAE 8090 gear oil, 750cc / 25.4oz 7. Reinstall the fill hole plug and torque to 2-3lbf-ft. 8. Dispose of used oil at a proper recycling station as required by law.
There is an oil sight glass in the side of the transmission case to check the level of the oil in the gear box. The oil level is correct when the level in the sight glass is half way up the glass. The level should be checked with the engine stopped and cold. Checking the level when the engine is hot can cause a false reading and lead to a low gear oil level. Your gear oil should be checked before each riding session. The gear oil should be changed before each riding season or every 1000 hours operation.

Page 13

Tires and Wheels

Spark Plug

Replace spark plug at the beginning of each season with a replacement plug NGK C7HSA. Disconnect spark plug wire. Clean dirt from around spark plug base with brush or compressed air. Remove spark plug with spark plug wrench. Set the spark plug gap on the new plug to 0.023 Install the new plug screwing it in finger tight and then use the plug wrench to screw the plug in another turn. Inspect the spark plug wire for cuts, nicks or other damage. Replace as needed.

Tire & Wheel inspection
It is important to inspect your tires and wheels for damage and wear before each riding session. Inspect each tire for cuts, tears and punctures. Inspect the wheel rim for dents and separation of the wheel from the tire bead. Replace any tire or wheel found to be damaged. Operating your ATV with damaged tires or wheels is dangerous. Damaged tires or wheels can result in a sudden loss of tire pressure and control which could result in injuries. Check your tire pressure before each riding session and at each refueling operation. Always check the pressure when the tires are cool. Use the tire pressure gauge that came with your ATV to check the tire pressure.

Spark Arrestor Screen

Required maintenance and cleanout: 1. After every 100 hours of operation the muffler should be cleaned by removing the clean out bolt by using a 12mm wrench. 2. After every 60 hours of operation the Spark Arrester has to be cleaned by loosening the retaining nut using a 10mm socket. Using pliers turn the sleeve of the Spark Arrester counterclockwise and pull out. Clean the screen with an exhaust cleaning solution and replace, securing it by tightening the retaining nut. 3. After every 200 hours of operation the Spark Arrester has to be replaced by loosening the retaining nut using a 10mm socket or wrench. Using pliers turn the sleeve of the Spark Arrester counterclockwise and pull out. Replace a new Spark Arrester and secure it by tightening the retaining nut.

Tire Pressure

Recommended tire pressure is:

Front Rear

Min Max Min Max
3.2psi / 0.23kg/cm2 4.0psi / 0.28kg/cm2 3.2psi / 0.23kg/cm2 4.0psi / 0.28kg/cm2
Wheel Nut torque 24-30 N/m (18-22 lb/ft)

Page 14

Air Filter
Air Filter Maintenance Remove the filter element from the air box and replace the filter element as needed.

Braking Systems

To maintain the highest performance from your engine and to reduce excessive wear that could cause engine failure the engine requires a continuous flow of clean air. Air is taken into the engine through an air filter to clean the air prior to mixing it with fuel in the carburetor. During normal operation the filter accumulates dirt from the air and will need to be cleaned to maintain the proper air flow. The filter should be cleaned every 30 days, more often if you ride in a dusty or dirty environment and the element should be replaced every year. The air filter box is located at the front of the engine under the fuel tank. Your ATV unit is equipped with dual front mechanical drum brakes and a rear hydraulic disc brake. The front brakes are applied by squeezing the brake lever on the right-handle bar, while the rear brake is applied by squeezing the brake lever on the left-handle bar. Proper maintenance of the brake system is a necessary part of safe operation of your unit. The brake systems should be inspected and tested before each riding session.

Page 16

Purging Brake Lines
After riding your unit, be sure to clean any build up of mud, sand and dirt from the brake rotor skid plate. This will protect the rotor disc from rust and corrosion.
For the hydraulic brake system to operate safely, the brake system must be purged of air in the lines and reservoir. To bleed the air will require two people to perform the following procedure.

To Fill the Reservoir

Remove the reservoir cover by removing the two cover bolts. Fill the reservoir to 1/8 from top with Dot-3 SAE-J1703 grade brake fluid. 1. Place a drain pan under the brake caliper to catch the fluid. 2. Open the bleeder valve turn counter clockwise. 3. Squeeze the brake lever to expel air from the system. 4. While holding the brake lever, close the bleeder valve. 5. Repeat steps 2 through 4 until the brake fluid coming from the bleeder valve is a solid stream without any air, then close the valve and replace rubber protection cap. 6. Test the brake system by squeezing the lever, the lever should feel firm and stop without fading.
Caution: DO NOT allow dirt to fall into the reservoir.
Refold the cover gasket as shown in picture and replace cover and bolts

Page 17

Drive Chain
the proper tension retighten the axle position locking bolt.
The drive chain will stretch with use and will require periodic adjustments. To check the chain tension, remove the chain guard and measure the slack. The amount of slack in the chain should not exceed 10-20mm or -. Inspect the drive and axle sprockets for worn, damaged or broken teeth. Replace as needed. Inspect the chain links for damaged, worn or loose rivets. Repair or replace as needed.
The chain should be kept well lubricated to prevent excess wear and premature failure. We recommend that you lubricate the chain every 15 hours of operation, or more frequently if needed, with a high quality chain lubricant.

Throttle Lever

Chain Slack Adjustment
The throttle lever is located beside the righthandlebar grip and is operated by using the righthand thumb. The lever is spring loaded and will return to the idle position when you remove your thumb from the lever. To accelerate the unit, simply press the lever forward to open the throttle slide in the carburetor. To slow the unit, reduce the pressure on the lever or remove your thumb and the throttle will return to the idle position automatically.
Loosen the axle position lock bolt slightly and turn the chain adjuster nut to take up the excess slack in the chain. Once the chain has been adjusted to

Page 18

Adjusting the throttle cable
The speed of the unit can be adjusted by adjusting the throttle stop screw to limit throttle travel. Loosen the throttle stop screw locking nut and turn the throttle stop screw clockwise to reduce the throttle travel thus reducing the maximum speed of the unit. Turning the stop screw counter clockwise will increase the throttle travel thus increasing the maximum speed of the unit. Tighten the stop screw locking nut when the desired throttle travel has been established.

Electrical Battery

The cable should be adjusted to allow for free travel before the throttle engages the carburetor throttle slide. Slide the adjuster cover down the cable to uncover the adjuster assembly. To adjust the cables free travel, loosen the locking nut of the cable adjuster, and turn the adjuster nut until there is free travel in the lever. Tighten the locking nut to secure the adjusting nut. Slide the cover back over the adjuster assembly.
The units battery is located under the seat and supplies electrical power to the unit. The battery is a 12 volt jell acid type that contains no liquid electrolyte. The battery should be removed from the vehicle when stored for extended periods and charged before being replaced in the unit. Use a trickle charger set at 12 volts to recharge the battery to full charge before replacing it in the unit.

Page 19

When reinstalling the battery, be sure to connect the red cable to the positive (+) terminal and the black cable to the negative (-) terminal. The battery should be replaced every three years or when it no longer holds a charge. Do not expose the battery, for extended periods of time, to freezing temperatures. If the battery has been frozen it will need to be replaced. There is an inline fuse on the positive lead of the battery to protect the wiring system from over loads. If your starter motor will not turn over and the battery is fully charged, check the inline fuse on the unit.
9. Check all nuts, bolts and other fasteners for loose conditions. 10. Inspect unit for any broken or damaged parts. 11. Check all indicator lights and switches for proper operation. 12. Insure you are wearing proper clothing and protective gear: Helmet, Gloves Pads, etc.

Starting Procedure

The following procedure must be followed each time you start your unit. Park the unit on a level surface and lock the parking brake. Place the transmission gear selector shaft in the N, Neutral, position. Turn the engine stop switch to the ON position. Turn the ignition key switch to the ON position. Apply slight pressure to the throttle lever. Press the starter button on the lefthandle bar. Your unit should start within 10 seconds of pushing the starter button. If the unit fails to start check the following. 1. Ignition key switch is ON 2. Engine stop switch is ON. 3. Parking Brake Locked ON. 4. Transmission selector switch in the N position

Replace the fuse with a 7A fuse.
Pre-Operation Inspection procedure
The following procedure must be performed before each operating session. Checking your ATV takes only a few minutes and may save you from serious injuries and costly repairs. 1. Check engine oil level. 2. Check engine fuel level. 3. Check brake operations and brake fluid level. 4. Check tire condition and pressure. 5. Check drive chain condition and slack. 6. Check throttle operation and free play adjustment. 7. Check engine stop switch for proper operation. 8. Check steering system. Look for free and smooth operation. Check all fastening hardware.

Driving your ATV

Your ATV should only be driven in an area that is designated for this use. Insure that the area is free of obstacles and other dangers that could cause a loss of control. Check with your local authorities for any regulations regarding the use of your ATV. Always keep your feet on the footrests and your hands on the handle bar grips while operating your ATV. Doing so will give you the best control of the unit. Start your ATV by following the starting procedure above and allow the engine a few minutes to warm up before releasing the parking brake. Start the unit by slowly increasing the throttle until the unit begins moving.

Page 20

Turning your ATV
Learning to turn your ATV requires you to learn to shift your weight and control the throttle to allow the rear wheels to turn properly. When making a turn, the wheels on the outside of the turn must travel a wider radius and thus a greater distance than the inside wheels of the turn. Since the rear axle does not permit a different rate of rotation, it is not enough to merely steer your ATV into the turn. To turn properly, steer in the direction of the turn and lean your body to the inside of the turn while supporting your weight on the outer footrest. Use the throttle to maintain power throughout the turn. If you do not use this turning technique the unit will have a tendency to continue in a straight line. If this occurs, release the throttle lever to allow the unit to stop. Avoid braking or accelerating until you have regained directional control.

Parking Your ATV

1. Always park your ATV on a level surface. 2. Turn the ignition key to the OFF position to stop the engine. 3. Set the engine stop switch to OFF position. 4. Engage the parking brake locking button. 5. Remove the ignition key to prevent unauthorized use or theft of your ATV.

Page 21

Standard Accessories
Your Yukon comes equipped with a front and rear cargo racks. The weight limit on these racks is 30Lbs each. Exceeding these limits can result in loss of control causing damage to your unit and serious injuries. Also standard is the full front brush bar. The brush bar protects the ATV and engine oil cooler unit. The screen on the bar must be kept free of debris to allow air to free flow to the oil cooling radiator.
Dual driving lights and Brake/Tail light for additional safety. Test the operation of your driving lights and Brake/Tail light before each riding session.
Auxiliary 12v DC electrical outlet for cell phone and other mobile equipment. (DON NOT Operate Vehicle while using Cell Phone)

Optional Accessories

ETON offers a factory trailer hitch kit for the Yukon II. The tongue weight limit is 70 lbs. and towing capacity of 330 lbs. (Ball not included)

Page 22

YUKON II Specifications

Engine

Type Displacement Bore / Stroke Compression Power Four cycle Air/Oil cooled 149.56 cc 57.4 * 57.8mm 9.7 : 1 10.6ps @ 7500rpm Automatic (C.V.T. V-Belt) 1730mm / 68.1" 980mm / 38.6" 1070mm / 42.1" 1115mm / 43.9" 172kg / 379lbs Dual A-arm Adjustable Shocks @ 3.5" travel Swing Arm Adjustable Shock @ 3.75" travel Dual Mechanical drum Hydraulic Disc 21/7-10 22/10-10 3.2psi / 0.23kg/cm2 4.0psi / 0.28kg/cm2 3.2psi / 0.23kg/cm2 4.0psi / 0.28kg/cmx 110mm Kei-Hin with Electric choke 1.12mm 0.35mm Back out turns Idle 1600 - 1800rpm

Transmission

Chassis
Overall Length Overall Width Overall High Wheel Base Dry Weight

Suspension

Brakes
Front Rear Front Tire Pressure Rear Min Max Min Max

Wheels

Bolt Pattern

Carburetor

Make/Size Main Jet Pilot Jet Air Mixture Adjustment Idle Speed

Page 23

Sprockets
Front Rear Chain 12 teeth 34 teeth #520 O-Ring 12V-9AH - GTX9 Type Volume Type Volume Type Volume Unleaded Gasoline 89 octane 6.5liters / 1.7gal SAE 30W 1.0liters / 1gt SAE 80/90 weight gear Oil 750cc / 25.4oz C7HSA/NGK U22FS-U Z9Y (Not recommended) 0.6-0.7mm / 0.023-0.027"

Battery Fluids

Fuel Engine Oil Transmission
NGK Nipendenso Champion Electrode Gap

Carrying Capacity

Rack Capacity Towing Capacity Maximum Rider Weight Minimum Rider Age Front Rear Trailer Weight Tongue Weight
16kg / 30lb 16kg / 30lb 150kg / 330lbs 32Kg / 70Lbs 150kg / 300lb 16 years

Page 24

Maintenance Schedule
First week Every 30 Days Every Year Notes
Replace Fuel & Vent Lines every 2 years Inspect as part of pre-ride inspection
Fuel Lines Throttle Operation Air Filter Fuel Filter Spark Plug Drive Chain Brake Shoes Brake System Brake Fluid Bolts, Nuts & Fasteners Wheels Steering system Suspension System C.V.T. Drive belt Transmission Oil Engine Oil I I I I I I I I C I I, L I I

R R R I

Inspect as part of pre-ride inspection Inspect as part of pre-ride inspection Replace every 2 years Inspect as part of pre-ride inspection Inspect as part of pre-ride inspection Inspect as part of pre-ride inspection Replace as needed

I, L I I

Every 6 months

I I R or 100 hrs

R or 100 hrs
Inspect as part of pre-ride inspection
Choke I Spark Arrester C every 100 hrs R every 200 Hours Battery I, C I = Inspect, Clean, Adjust, Lubricate or Replace as needed C= Clean L = Lubricate R = Replace Owners Maintenance Records Maintenance Preformed Date Preformed By

Page 25

YUKON II Wiring Diagram

Page 26

ETON AMERICA, LLC.

LIMITED VEHICLE WARRANTY

ETON America warrants all new ETON vehicles sold by authorized Eton Dealers to be free from defects in materials and workmanship, subject to the following exclusions and limitations. New vehicles sold by an authorized dealer to original retail consumers are covered by this policy for a period of six (6) months from the date of delivery. There is no mileage limitation. Vehicles used in rental service or for certain commercial purposes are specifically excluded from this policy. (Check with your dealer for warranty application.) Items and conditions that are specifically excluded from this warranty program are; 1. Damage caused by accidents, misuse, negligence, improper vehicle operation. 2. Any modification or alteration to any standard specifications or equipment. 3. Any repairs made by an unauthorized dealer or service firm. 4. Use of non-ETON genuine parts for repairs or alteration to standard specifications. 5. Damage caused by failure to perform factory scheduled service maintenance. 6. Damage which occurs as a result of improper storage. 7. Damage caused by the use of improper fuel or lubricants, and/or failure to use proper oil/gas mixture on two stroke models. The following normal wear parts are specifically excluded from warranty coverage: 1. Rubber parts 2. Tires 3. Belts 4. Brake linings 5. Normal wear item 6. Brake parts 7. Cables 8. Filters 9. Spark plugs 10. Bulbs 11. Batteries 12. Sprockets 13. External springs 14. Seat and hand grips.

Page 27

Scheduled maintenance service is the responsibility of the owner during and after the warranty period. In the event of a failure or required repair, the owner should take vehicle to an authorized dealer for repair without undue delay and within a maximum of thirty, (30), days of the occurrence of the problem. All eligible warranty repairs must be made at any authorized dealers normal place of business. Any transportation costs, or other expenses which may occur in order to obtain warranty service, are the responsibility of the owner. All eligible repairs covered under this warranty will be paid to the servicing dealer only, by ETON America, and no additional payments shall be made for authorized warranty repairs. Dealer and/or ETON America are not responsible for loss of use, other damage or inconvenience due to warranty repairs. It is the customer/buyers responsibility to review with the selling dealer the predelivery service schedule to assure machine is properly serviced prior to delivery acceptance. It is recommended that the buyer take a test ride to familiarize themselves with the machine and to make certain the unit is in proper operating condition. The dealer is responsible for checking and performing all items on the set-up and pre-delivery checklist prior to delivery to the customer. This warranty is valid at any authorized ETON Dealer in the United States only. In the event you experience any problem obtaining prompt service, contact ETON America, customer service department for assistance. Always consult first with your selling dealer and or service personnel for assistance with any service work or repairs. In the event you have a problem obtaining service send your name, address, and vehicle identification number to Eton America for assistance. The above stated policy is the only policy offered and backed by ETON America, and no other organization or individual is authorized to make or offer any different arrangements. Some states prohibit certain limitations or conditions or do not allow exclusions or limitations. You may be eligible for additional consideration, so check with your local dealer or appropriate state agency for assistance. Rights vary from state to state, and you may have other rights not offered in this warranty. ETON America warrants all new vehicles comply with applicable US regulations.

Page 28

Owners Notes:

Page 29

Page 30

Yukon CXL150

by E-TON
Engine Type Displacement Bore / Stroke Compression Ratio / Pressure Torque / BHP EPA Approved Starting Transmission Type Chassis Overall Length-With-Height Wheel Base Seat Height Ground Clearance Dry Weight Suspension Front Rear Brakes Front Rear Tires Front Rear Front Tire Pressure Wheels Bolt Pattern Front Rear 4 x 160mm (P.C.D.) 4 x 110mm (P.C.D.) Kei-Hin CVEK-019 26mm with Manual Choke 1.12mm 0.35mm Back out 1 - 2turns Idle 1600 - 1800rpm 520x12t 520x24t #520 O-Ring 12V-9AH - GTX9 10Amp Unleaded Gasoline 89 octane 6.5liters / 1.7gal SAE 30W 1.0liters / 1.0qt SAE 85/140 weight gear Oil 750cc / 25.4oz N/A N/A Standard equipment N/A 14kg / 30 lb 14kg / 30 lb 150kg / 330 lb 32kg / 70 lbs 150kg / 330 lbs 16 years Min Max Min Rear Max Four cycle air/oil cooled (EPA Compliant) SOHC 149.56cc 57.4 * 57.8mm 9.7 : 1 / 150-190psi 10.6N m @ 7500rpm / 10.0BHP Meet or exceeds EPA clean air requirements and CA Green Sticker Electrical starter with kick start backup Automatic (C.V.T. V-Belt) with forward/reverse shift 1730mm / 68.1" - 980mm / 38.6" - 1070mm / 42.1" 1115mm / 43.9" 700mm / 26.6" 140mm / 5.5" 172 kg / 379 lbs Independent A-arm Adjustable Shocks @ 3.5" travel Swing Arm Adjustable Shock @ 3.75" travel Dual Mechanical Drum Hydraulic Disc 21/7-10 22/10-10 3.2psi / 0.23kg/cm2 4.0psi / 0.28kg/cm2 3.2psi / 0.23kg/cm2 4.0psi / 0.28kg/cm2

Just go there!

Yukon CXL 150
Red Silver Real Tree Camo
Introducing the E-TON Yukon II ATV. E-TONs biggest utility ATV, the Yukon II includes a 149.56cc four-stroke air/oil cooled engine, Automatic C.V.T. belt transmission with forward/reverse shifting, front and rear carrying racks, and a U.S. Forest Service-approved spark arrestor. The Yukon II meets or exceeds EPA clean air requirements and is eligible for the California Green Sticker. Includes full six month limited factory warranty. Designed for riders ages 16 and up.

Optional Accessories

Heavy duty trailer hitch Light duty trailer hitch E-TON safety flag Helmets and apparel available on the web site ETON AMERICA

www.etonamerica.com

Carburetor Make/Size Main Jet Pilot Jet Air Mixture Adjustment Idle Speed Sprockets Front Rear Chain Battery Jell Acid (Maintenance Free) Main Fuse Fluids Type Fuel Volume Type Engine Oil Volume Type Transmission Volume Safety Features Safety Tether Switch Remote Stop Switch Enclosed Foot Rest Area Enclosed Engine compartment Carrying Capacity Front Rack Capacity Rear Towing Capacity Trailer Wgh
Tongue Wgh Maximum Rider Weight Minimum Rider Age