zones, exit error, recent close, swinger shutdown
Cancel code and system stabilization during

power-up

Keypad programming and remote
programming via PC and modem
Arming by keyswitch in Away or Stay mode Keypad tamper/lockout with optional CS

reporting

Upload/download and remote commands 3 methods of uploading/downloading: PC
operator-initiated, unattended downloading, and on-line downloading
Restore transmission options: after loop or

after bell

Paging (audio format) capabilities Auto Arming at a specific time of day with
capability to arm in either Away, Stay, or Instant modes Two entry timers
Fire zone reset through keypad Glassbreak reset through keypad Bell Test, Low Battery Test, AC Loss and
Communications Failure indications
Input power: 16.5VAC, 25VA; 12VDC, 4-7AH Output power: 12VDC, 500mA Bell output power: 12VDC, 1A
OMNI-848/OMNI-848EU Installation and Setup Guide

Special Notes

IMPORTANT - Failure to install and program this unit in accordance with the UL requirement is a violation of the listing mark. For more information on UL Listings, contact Underwriters Laboratories, Progress Department, 333 Pfingsten Road, Northbrook IL 60062. UL Listings The OMNI-848 is the Residential (Household) version of the control panel, and has been Listed by Underwriters Laboratories for the following applications: UL 1023 Household Burglary UL 985 Household Fire Warning
FCC Registration Number: 5GBUSA-44003-AL-E REN: 0.1B The OMNI-848EU has not been evaluated by Underwriters Laboratories. References to Programming Questions Programming questions are grouped into 4 installer programming submodes, as follows: 1 System Options 2 Zone and Report Code Programming 3 Wireless Zone/Keyfob Programming 4 Zone Descriptor Programming Throughout this manual, programming question references without a submode designation pertain to questions in submode 1 (system options). Programming questions for other submodes include the appropriate submode number.

System Wiring and Hookup

System Wiring Diagram
IMPORTANT: All control panel wiring should be completed prior to applying power to avoid possible harm to circuits due to electrostatic discharge. SYSTEM STABILIZATION MODE: When powering up a system that was previously armed when power was removed, the system will enter a 2-minute stabilization period. This 2-minute interval is used to allow motion detectors to stabilize. PLEASE STAND BY and POWER UP DELAY are displayed on the OMNI-LCD, OMNI-LCD-US, and XK7LC keypads. PL is displayed on the OMNI-KP and OMNI-KP-US keypads, and the Armed LEDs on both types of keypads are lit. All LEDs on the XK108 keypad are lit.

BELL SUPERVISION (Bell ) - To meet the NFPA 72 requirement, program
Question 17, Location 3, in Submode 1 for bell supervision. The bell is then supervised for an open circuit (not a short circuit) across the bell output terminals; the keypad will indicate that a fire trouble condition has occurred and fire trouble is reported to the CS if enabled. If the bell is already ringing, the supervision will not take effect until after bell cutoff time.
SIREN SUPERVISION (Self-Contained Siren/Speaker)
(Not for use in UL installations.) To meet the NFPA 72 requirement, program Question 17, Location 3, in Submode 1 for bell supervision. The siren is then supervised for an open circuit (not a short circuit) across the bell output terminals; the keypad will indicate that a supervision condition has occurred and bell supervision is reported to the CS if enabled (program mode 2, Question 79, Locations 1,2). If the siren is already sounding, the supervision will not take effect until after bell cutoff time. NOTE: Use FBII models ZR815C, ZR815EC, or ZR830EC.
Section 2: System Wiring and Hookup
5 SIREN SUPERVISION INPUT:
The bell output may be supervised when a conventional bell or a self-contained siren is connected. When you connect a conventional bell or a self-contained siren to the bell output terminals (3 and 4), place the jumper JP4 across pins 1 and 2. When you connect an external siren driver to the bell output terminals, connect the supervision wire to the siren supervision terminal of the siren driver, and place the jumper JP4 across pins 2 and 3. A supervisory condition will generate a pulsing keypad sounder. Also, the supervisory LED on the keypad will pulse. The sounder may be silenced by entering a valid user code while the system is disarmed. The LED will continue to pulse until the supervision is fixed. If a bell, self-contained siren, or external siren driver is not connected to the bell output terminals, a 100-ohm resistor must be placed across the siren supervision input to prevent a bell supervision error, or you must disable bell supervision (Programming Question 17, Location 3). Bell supervision will be reported to the CS if CS code is enabled.
6(+) & 7() SMOKE DETECTOR POWER:
This system accepts 9.5 - 12VDC 4-wire smoke detectors only. Approximately 50mA of current is available at these terminals for powering all detectors. These terminals adhere to the fire verification and reset logic, which is explained in the zone types section of this manual. For UL installations, use a UL Listed smoke detector.
REGULATED POWER (11.5 - 13.1VDC):

6(+) & 4(-)

The total regulated output power for motion detectors and other external devices is 500mA at 11.8 - 12.5V for residential applications, or 12.0 12.5V for commercial applications, with less than 100 mVPP ripple. The total regulated output capacity of the OMNI-848 includes the power available from these terminals (6 and 4) as well as the power used by the keypads (23 [+] and 20 []) and smoke detectors (7 [] and 6 [+]). Therefore, to determine the total power available from these terminals, subtract the power consumed by the keypads and smoke detectors. The maximum auxiliary output for UL installations is 180mA.

BACKUP BATTERY: The RED (+) and BLACK (-) flying leads must be connected to a 12VDC
4-7AH battery to serve as backup power in the event of AC loss. A battery test occurs approximately every minute. Low-battery condition occurs at nominal 11VDC. The keypad AC/LOW BAT LED and buzzer pulse slowly when a low-battery condition is detected. The system reports this condition to the CS if programmed to do so. There is also an option that prevents the system from arming if a low battery has been detected (see Question 19, L2). Battery restore will occur within 4 minutes, at the next battery test. The buzzer may be silenced by entering any valid user code. NOTE: For UL installations, use two 4AH batteries connected in parallel.
TRIGGER OUTPUTS: The control panel has four built-in programmable trigger outputs. See
programming questions 47-48 for valid trigger types and programming. NOTE: In order to connect devices to the triggers, use connector XL4612TC (trigger cable). Connect to terminal P1 VBELL to obtain a POSITIVE reference point. Triggers 1, 2, 3, and 4 will go to a negative ground potential when active. For UL installations, the trigger outputs shall be connected to devices rated to operate over the range from 10.1 14.0VDC at 50mA.
Auxiliary Device Current Draw Worksheet
DEVICE Control Panel OMNI-LCD/OMNI-LCD-US (Standby/Alarm) XK7LC OMNI-KP/OMNI-KP-US (Standby/Alarm) XK108 PIR Smoke Detector Glass Break Detector CURRENT DRAW FOR EACH 65mA 40mA/180mA 65mA 40mA/70mA 30mA ** ** ** ** ** TOTAL CURRENT FOR ALL DEVICES = (500mA max.) NUMBER OF UNITS TOTAL CURRENT FOR EACH
** If you are using devices such as PIRs, smoke detectors, etc., refer to the specifications for that particular device's current draw. If the total current draw exceeds 500mA, use an additional power supply. NOTE: For UL installations, do not exceed 180mA. NFPA, UL, and the California State Fire Marshal require the backup battery to provide power for 24 hours. The maximum aux. power varies by the ampere/hour rating of the battery used: 5AH = 95mA; 7AH = 180mA; 8AH = 210mA.
Wiring Information for Keypads & Other Devices
If single or multiple devices are connected to a single 4-wire or 2-wire run ("daisy-chained") to the control terminals, determine the current drawn by the unit(s) connected to the single wire run, then refer to the Wiring Run Table below to determine the maximum wire length that can be safely used for each wire size. In some cases, the total current drawn may result in a value not shown in the table. For example, if you plan to use #22 gauge (0.64mm) wire and the total current drawn is 400mA (a value between 300mA and 500mA), the maximum wire length you should use is approximately 65 ft or 20 m (a length between 50 and 80 ft or 15 and 24 m). Other maximum wire lengths for values of current not shown in the table can be calculated in a similar manner.

OMNI-848/OMNI-848EU Installation and Setup Guide Assigning Partitions and Pager Open/Close Reports to Users Users are automatically enabled for the partition where their code was added. You can also allow users to access other partitions and/or enable open/close pager reports for a user by using the #7 command as follows: [#] + [7] + Master User Code + User No. + 1, 2, 3, or 4 where: Master User Code = user with authority level 1 or 2 User No. = the user that will be assigned access to other partitions 1, 2, 3, or 4 = select 1, 2, 3 to assign access to a partition to that user; select 4 to enable open/close paging report for that user To exit this mode, press []. User code programming can ONLY be performed while the partition is DISARMED.

User Deletion

User codes (02-64) can be deleted from any disarmed partitions keypad, regardless of where the users code was first added. Once deleted their values are null. To Delete Users: Press [CODE] KEY + MASTER USER CODE + USER NO. + [#] where: [CODE] = CODE button on keypad. MASTER USER CODE = Master User code. USER NO. = the desired user number being deleted (02-64). [#] = # (pound) button.

Special Keypad Functions

The system is capable of transmitting four special keypad functions, as follows:
KEYSTROKES # & (at the same time) 7 & 9 (at the same time) 1 & 3 (at the same time) User code 61-64 OPTIONS (aud./silent; arm; beeps; triggers) CS REPORT ENABLE Submode 2, Question 74, L1-L2 See Question 32, L1, L2 Immediate and unabortable. Submode 2, Question 76, L1-L2 See Question 31, L3, L4 Submode 2, Question 76, L3-L4 See Question 31, L1, L2 Submode 1, Question 18, L1 Always SILENT
The keypads have additional keys dedicated for emergency conditions. These can be activated by pressing both keys at the same time (see the Keypad descriptions at the beginning of this section).

Quick Command Modes

The end user can perform the following commands (if programmed):

L 001 ALARM ZN APR, 10:38 P1
where: Line 1: event number (L001L128), event display, zone no. (0124), or user no. (0132) Line 2: date, time, partition (14) if a partitioned system Pressing either the [STAY] or the [] key exits this mode. Pressing any other key advances to the next valid entry. SET AUTO ARM TIME: #54 If auto arming is enabled in programming Question 33, L1-L3 (partitions 1-3), then pressing [#] + [5] + [4] sets the auto arm time of the current partition. If a user code is required to set the time, then enter: [#] + [5] + [4] + USER NO. + HOUR + MINUTE where: USER NO. = a valid 4-digit user code HOUR = two-digit hour of day in military time; e.g., 7AM = 07; 3PM = 15 MINUTE = two-digit minutes of hour; e.g., 9 min = 09; 29 min. = 29 If a user code is not required to set the time, then enter: [#] + [5] + [4] + HOUR + MINUTE In either case, the LCD keypads display a prompt for each entry. On LED keypads, the sounder beeps after each entry. The auto arm time represents the time of day that the area will automatically arm if it is not already armed. In addition, it can be programmed to arm in the STAY or INSTANT modes. An audible warning can be programmed in Question 20, L2 to sound at the keypad 2 minutes prior to arming. This signal (4 short beeps every 15 seconds for 2 minutes prior to arming) warns the occupants that the system will auto-arm in two minutes. If a user code is entered within this warning period and the system is disarmed, then the auto-arm time for that day is canceled. The system then generates an audible acknowledgment (1-second keypad sounder) and the lights on the LED display scroll to show that the auto arm time was suspended. LCD-based keypads display AUTO ARM CANCELED. The system exits this mode either automatically (no keys pressed), after the last entry (MINUTE), or after the [] key is pressed. NOTE: Auto arming will arm the system and bypass any zones that are not ready. Therefore, it is recommended that bypasses should be reported to the CS if auto arming is programmed.
Auto arming is not suitable for UL applications. LOSS OF TIME WARNING: If auto-arming has been enabled and no time is defined, a warning appears on the keypads. This can occur if time ([#] + [3] command) has not been entered, or if the system has totally lost power (AC & DC) and the time is probably incorrect. The loss of time warning consists of the LEDs on the keypads scrolling in sequence or a text message on LCD keypads. This occurs every 30 seconds until the time is set. DISPLAY PANEL REVISION: # 55 (LCD Keypads Only) Pressing [#] [5] [5] displays panel revision level on the LCD keypads. The system exits this mode when the star [] key is pressed.

OMNI-848/OMNI-848EU Installation and Setup Guide 4. Press the [INSTANT] key to proceed to Question 02. Next, enter the desired unattended identification number (each digit followed by the [#] key). This will be used by the Compass software in the CS downloading computer to determine the proper account information to download to this subscriber. The unattended identification number must be 12 digits in length. It is the unattended identification number (not the account number) that will be communicated to the Compass software in the CS downloading computer. For unattended identification numbers fewer than 12 digits, you must enter leading 0's to make the number 12 digits long. Example: for account number 345, enter 0 # 0 # 0 # 0 # 0 # 0 # 0 # 0 # 0 # 3 # 4 # 5 # 5. Press the [STAY] key to exit programming mode. The control panel now dials the telephone number entered into the callback number (Question 03). The downloading computer must be placed into the Unattended Communications option from the main menu. Upon connection with the computer, the customer account number programmed in step 3 is obtained and the system performs the desired download operation. NOTE: The CS downloading computer must be waiting in the Unattended Communications mode and preprogrammed with the account information in order for the unattended download to be functional. Press the [INST] key to exit programming mode without activating Unattended mode. INSTALLER MODE 9 (ON-LINE DOWNLOAD) In this mode, the installer can initiate a remote communications session with the CS downloading computer from the control panel location. Typically, a remote communications session is initiated by the CS. On-line downloading allows the installer to call the office (from the same telephone line as the panel), discuss the action required, and allows the CS operator to complete the request while on-line, with no additional telephone call needed. Online connection can be made as follows: 1. Installer completes installation and attaches a handset to telco terminals (tip and ring) or uses the standard home telephone to dial the CS downloading modem telephone line. Connection is made with a person at the CS downloading computer and the account to be downloaded is verbally identified. The downloading computer operator selects the Online Remote Operations from the device menu. 2. The installer enters the on-line download sequence: [CODE] [] [INSTALLER] [9] or uses the end-user command of # 9, if enabled (Question 18, L1). This causes the control panel to react as if it had received a request for a remote communications session, and to look for the standard panel-to-CS protocol. 3. Once the standard connection is made, the necessary remote communications sessions can take place (upload, download, remote commands). 4. The installer hangs up the telephone or removes the headset from the line to prevent interference, which may affect upload/download data. The downloader software automatically terminates the connection after remote communications end.

Example: To enter an A, press [CODE] followed by [1]. Exit System Program Mode After all programming has been completed, press the [STAY] button to exit the system program mode. Question Acknowledgment The keypad beeps between keystrokes. In addition, a beep confirms advancement between question numbers. Four beeps are generated if an invalid input is entered. Upon entry of an invalid input, you remain at the same question number and location as before the input error.
Summary of System Programming
To Enter Programming: Press [CODE] + [] + 4- or 6-digit Installer Code + [1] + Submode 1-4. To Skip a Question: Press [] + 2-digit Question Number. To Move Within a Question: Press [#] until the desired location is reached. To Enter Data: Press a single digit: 0-9, A-F [#] Hexadecimal Entries: A = [CODE] [1] B = [CODE] [2] C = [CODE] [3] D = [CODE] [4] E = [CODE] [5] F = [CODE] [6]
To Exit Programming: Press the [STAY] button. This section defines the programming questions and the values for each question. You should complete the SYSTEM PROGRAMMING WORKSHEET (insert) before entering data.
Installer Mode 1, Submode 1: SYSTEM OPTIONS
Enter Installer Programming mode, then press [1] at the submode prompt to enter System Options mode.
QUESTION 00 INSTALLER CODE

L1 L2 L3 L4 L5 L6

NOTE: When Programming Submode 1 is entered, the System automatically displays Question 01. To display this question for review and/or modification of the Installer Code, you enter [] + [0] = [0]. Enter the 4- or 6-digit Installer Code in Question 00 locations L1L4 for a 4-digit code or L1 L6 for a 6-digit code. When using a 4-digit code, L4 and L5 may be left at the default value of 0. IMPORTANT: When using a 6-digit code, enter the third through sixth digits of the code in L1L4 respectively and the first and second digits in L5 and L6 respectively. For example:
Section 6: System Programming 4-digit code of 1234 enter 6-digit code of 123456 enter

L4 L5 L6

Note that if the system is set for 4-digit codes and you enter a 6-digit code, the first two digits of the code (L5 and L6) are stored into memory but will not become active until the system is set for 6-digit codes (Submode 1, Question 17, L3) and the programming mode ends.
QUESTIONS 01-06 TELEPHONE and PAGER NUMBERS Enter the telephone number (including area code and/or dialing prefix, IF NECESSARY) of the primary central station receiver in Question 01, L1 L20. Example: If the primary telephone number to be entered is: 1-516-921-6704, enter (on Programming Worksheet): 15169216704. Enter the valid digits from the table below.
Entry 0-9 A B C D E F Function 0-9 Signifies end of the phone number Star () 3-Second pause Pound (#) 70C (Touch Tone) 1170C (Rotary) 800 Comments Enter after last digit of phone number Enter whenever the star is used Provides delay to wait for dial tone Enter whenever the pound is used Enter to disable Call Waiting Enter to dial 800

L2 Entry Supervision Restore Tamper Restore RF Low Bat. Restore

Q 16, L3

CS Dialer Attempts
Section 6: System Programming This option selects the number of times the communicator will attempt to dial both CS receivers. If CS #2 is not programmed, then this option determines the dialer attempts to CS #1. Enter the number of attempts, 1-15. NOTE: This option is valid for all CS receiver formats.
L3 Entry Dialer Attempts same as L3 Entry A B C D E F Dialer Attempts 14 15

Q 16, L4

For UL installations, you must select a value between 5 and 10. Restore Reporting Enter the digit for the type of restore reports to be sent. Program the actual trouble restore report code in Submode 2, Question 80, L4.
L4 Entry C D E F Send AC Restore Send Low Bat. Restore Send Zone Restore Restore Follows Loop
Send Zone Restore & Restore Follows Loop: Normally, zone restores are sent at bell cutoff, or when the panel is disarmed, and when the panel is reset. If you select Restore Follows Loop, zone restore reports will be sent as soon as the zone restores.

SYSTEM OPTIONS

This question defines various system-wide options.
OMNI-848/OMNI-848EU Installation and Setup Guide Q 17, L1 Enter the L1 digit for the desired options from the table below.
L1 Entry A B C D No Bell if Dial Delay Fast Zones 7/8 DoubleBalanced Zones
No Bell if Dial Delay: If selected, bell sounding will not occur until the dialer is activated (bell is delayed by the same amount of time as the dial delay setting). See Question 24, L4 for setting the dial delay (15-255 seconds). Fast Zones 7/8: Sets zones 7 and 8 to fast response (10ms). If set, these zones must be wired as NC loops. Double-Balanced Zones: Select if using double-balanced zones. This option allows hardwired zones to be wired such that a tamper will be detected on an open or a shorted loop. Q 17, L2 Enter the L2 digit for the desired options from the table below.
L2 Entry A B C D E F XL 4705 Relay Enable RF Receiver Used
4705 Relay Enable: Enables the relay module. If used, the systems built in triggers 3 and 4 will no longer be available as triggers. Instead, they will serve as clock and data lines, respectively, for the relay module. RF Receiver Used: Enables the RF receiver, if used.
L2 must be programmed as 0 or 2 for UL installations.
Section 6: System Programming Q 17, L3 Enter the L3 digit for the desired options from the table below.
L3 Entry A C D E Euro Pulse Dialing TouchTone Dialing U.S. Pulse Dialing User Codes 4-digit 6-digit Bell Supervision

Q 17, L4

Dialing Method: Select the type of dialing desired. User Codes 4/6 Digits: The system supports either 4-digit or 6-digit user codes. If this option is selected, the system is set to use 6-digit codes. Existing 4-digit user codes will be automatically changed to include 00 before the existing code (e.g., 1234 becomes 001234). If the system is set to 6-digit codes and is changed to 4-digit codes, the system automatically deletes the first two digits of existing 6-digit user codes (e.g., 123456 becomes 3456). Bell Supervision: Select this option to comply with NFPA 72 requirements. If selected, the bell will be supervised for an open circuit across the bell output terminals. If a fault is detected, the keypad will display a bell supervision condition. Enter the L4 digit for the desired options from the table below.

Quick Exits must not be enabled for UL installations.

SOUND OPTIONS

This question defines sounder and bell options. Q 20, L1 Enter the L1 digit from the table below. Applies only to wireless keys.
L1 Entry A B C D E F FOB/keysw. Ding Arm Bell Ding Disarm Ding Fast Ding
Fob/Keyswitch Ding: If selected, arming from a keyfob or keyswitch causes the alarm sounder to ding twice; disarming causes the bell to ding once, provided that arm/disarm bell ding options (see below) are selected. Arm Bell Ding: If selected, the alarm sounder dings twice upon arming. Disarm Ding: If selected, the alarm sounder dings once upon disarming. Fast Ding: If selected, the arming and disarming dings will be shorter tones.
OMNI-848/OMNI-848EU Installation and Setup Guide Q 20, L2 Enter the L2 digit from the table below.
L2 Entry A B C D E F Threshold Sounder Threshold Bell CS Test Ringback Invert Bell Output
Threshold Sounder: Alerts the user to the end of exit time by sounding 4 rapid beeps 30, 20, 10, and 5 seconds before exit time expires. When exit time expires, the keypad sounds an acknowledgment tone. Threshold Bell: Similar to threshold sounder option, except the alarm sounder will sound 1 second at 30, 20, 10, and 5 seconds before the end of exit time. CS Test Ringback: If selected, keypads beep after the central station has received the system test code. Inverted Bell Output: If selected, the bell output signal is inverted. This is useful when using bell boxes requiring inverted signals. NOTE: If inverted bell output option is used, bell supervision must be disabled (Q17, L3).

Q 20, L3

Enter the L3 digit from the table below.
L3 Entry A B C D E F Phone Fail Enable Phone Fail Sounder Phone Fail Bell Bell Ring Cancel
Phone Fail Enable: If selected, the phone line is monitored. If no phone line is detected for4-8 minutes, a phone fail message is displayed, and, if the phone fail sounder (L2) and/or phone fail bell options (L3) are enabled, a sound occurs. The phone fail is automatically cleared approximately 4 minutes after the phone line has been restored. Bell Ring Cancel: If selected, the bell dings upon receiving cancel code.

Q 20, L4

Selects whether you want the system to sound upon the listed conditions. This option does not affect keypad display of these events.
Section 6: System Programming Enter the L4 digit from the table below.

Section 6: System Programming Q 28, L4 Pager Enables for Partitions and Follow Me
L4 Entry A B C D E F Enable User Page Part. 1 Enable User Page Part. 2 Enable User Page Part. 3 Enable #58 Follow Me
Enable User Page Part. 1-3: If selected, the open and/or close events selected in L1-L3 above are reported to a pager for users in a particular partition. This setting can be toggled by using the #8 command. Enable #58 Follow Me: If selected, enables the #58 Quick Command. The #58 Quick command is used to modify the pager telephone number from the keypad.
KEYPAD TAMPER, ARMING, AND RF JAMMING
L1 L2 Tamper L3 No Arm L4 Jam
This question defines keypad tamper, arming, and jamming options. Q 29, L2 Enter the L2 digit for the keypad tamper options from the table below.
L2 Entry 7 Keypad Tamper Enable Keypad Tamper Sounder Keypad Tamper Bell
Keypad Tamper Enable: If enabled, the system will monitor the keypads for a keypad tamper report. If a keypad tamper is reported by a keypad, a report will be sent to the central station if enabled in Submode 2, Question 77, Locations 3 and 4. Keypad Tamper Sounder: If enabled, the keypad sounder will sound on a keypad tamper condition. Keypad Tamper Bell: If enabled, the bell will sound on a keypad tamper condition.

Q 29, L3

NOTE: Keypad tamper is only available on some OMNI-LCD, OMNI-LCD-US, OMNI-KP, and OMNI-KP-US keypads. Refer to your keypad instructions to see if your keypad has keypad tamper reporting capabilities Enter the L3 digit for the jamming, supervision and no AC arming options from the table below.
L3 Entry 7 No Arm if Jam No Arm if Super No AC/2X
No Arm if Jam: If selected, when the user tries to arm the system when in a jam condition, the system will provide a negative acknowledgement and will not arm. No Arm if Super: If selected, when the user tries to arm the system and a supervised RF zone has a fault condition, the system will provide a negative acknowledgement and will not arm. No AC/2X: If selected, when the user tries to arm the system with an AC fail condition, the system will provide a negative acknowledgement and will not arm. To arm the system, the user must enter their code a second time.
OMNI-848/OMNI-848EU Installation and Setup Guide Q 29, L4 This question defines if the system should detect a jam signal from the RF receiver, and if detected, determines the type of jamming to be recognized and the action to be performed (sounder or bell).Enter the L4 digit from the table below. NOTE: RF Jamming detection will only function if the system uses a ZR402EU or OMNI-RF Receiver that has jam output capability.

QUESTION 49-51 PARTITION DESCRIPTORS
These questions allow you to enter up to 16 partition descriptor digits for partitions 1-3. There is no provision for the common partition descriptor. Each digit corresponds to a single character in the descriptor. Q 49 DESCRIPTOR FOR PARTITION 1 Q 50 DESCRIPTOR FOR PARTITION 2 Q 51 DESCRIPTOR FOR PARTITION 3
Summary of Keypad Functions

User Functions

ARMING/DISARMING: STAY ARMING: INSTANT ARMING: STAY/ INSTANT ARMING: BYPASS/UNBYPASS: MULTIPLE BYPASS: QUICK BYPASS: USER CODE PROGRAMMING: USER PART/PAGER ASSIGN: USER CODE DELETION: CHANGE PARTITION: QUICK ARM: QUICK FORCED ARM: SET TIME: DISPLAY ZONE DIR.: SET AUTO ARM TIME: DISPLAY/TOGGLE CHIME: DISPLAY TIME: DISPLAY AUTO ARM TIME: KEYFOB LOW BATTERY TEST DOOR STRIKE: USER ON-LINE DOWNLOAD: PANIC: FIRE: AUXILIARY: AMBUSH: User Code [STAY] + User Code [INSTANT] + User Code [STAY] + [INSTANT] + User Code [BYPASS] + User Code + Zone No. [BYPASS] + User Code + Zone No. + [BYPASS] + Zone No., etc. [BYPASS] + Zone No. [CODE] + Master User Code + User No. + New User Code + Auth Lev [#] + [7] + Master Code + User No. + [1, 2, 3, or 4 (pager)] [CODE] + Master User Code + User No. + [] [#] + [0] + Level 1 or Level 2 User Code + [0,1-3,9] [#] + [1] [#] + [2] [#] + [3] + User Code + Hour + Minute + Day + Year + Crystal Adjust (optional) + Adjust Value (optional) [#] + [4] (LCD Keypads only) [#] + [5] + [4] + User Code + Hour + Minute [#] + [6] [#] + [5] + [1] (LCD Keypads only) [#] + [5] + [2] (LCD Keypads only) [#] + [5] + [6] + user code or [#] + [5] + [6] (LCD Keypads only) [#] + [5] + [7] + [CODE] + Trigger Number [#] + [9] [#] + [] at the same time [7] + [9] at the same time [1] + [3] at the same time User Code 60-64, if programmed
NOTES: User codes can be 4 or 6 digits, depending on system programming (Question 17, L3). Zone numbers, hour/minute, day/year, and trigger numbers require 2-digit entries.

Installer Modes

KEYPAD PROGRAMMING: SYSTEM DEFAULT: DEFAULT USER CODES: PROGRAM REVIEW MODE: WALK TEST SYSTEM LOG VIEW: SYSTEM DEFAULT: CLEAR TAMPERS: DEFAULT USER CODES: UNATTENDED DOWNLOAD: ON-LINE DOWNLOAD: [CODE] + [] + Installer Code + [1] + [1-4 submode] [CODE] + [] + Installer Code + [1] + [1-4 submode], then press [1] + [3] at the same time [CODE] + [] + Installer Code + [1] + [1-4 submode], then press [7] + [9] at the same time [CODE] + [] + Installer Code + [2] [CODE] + [] + Installer Code + [3] [CODE] + [] + Installer Code + [4] [CODE] + [] + Installer Code + [5] [CODE] + [] + Installer Code + [6] [CODE] + [] + Installer Code + [7] [CODE] + [] + Installer Code + [8] [CODE] + [] + Installer Code + [9]

OMNI-848/OMNI-848EU Installation and Setup Guide This format transmits in DTMF a total of 7 digits (including the parity digit). This format is similar to the 4x1 Extended or 4x2 formats in that the output sends a 4-digit account and 2digit event code. However, its advantage is speed because it transmits touch-tones instead of pulses and it always sends a parity digit. Examples: 1 (1st round) (resulting data) Burglary Zone 1

ADEMCO Point ID

The Point ID Reporting Format: AAA 18 QXYZ GG ZZZ where: AAAA = Four-digit Account Number (Program Questions 7-14) 18 = Uniquely identifies this format to the receiver and to an automation system, but is not displayed or printed. Q = Event qualifier, which gives specific event information 1 = New Event or Opening 3 = New Restore or Closing XYZ = Event Code: The event code is a 3-digit code (3 decimal digits). For zone alarms and some conditions, this can be specified; other conditions are dedicated; see the tables below. GG = Group number; this represents the partition number (01-04, with 04 being the common partition). ZZZ = Zone, sensor, or user identifier (3 decimal digits). For user-initiated actions such as openings/closings, this is the actual user number (01 - 15). This format is also known as ADEMCO Contact ID. A total of 16 digits (including the parity digit) are sent in DTMF. It enables reporting of 999 (001 - 999) unique zone or user identifiers instead of the 15 possible identifiers of most other pulse formats. This feature allows the full reporting capability of this system (48 zones and 64 users). In addition, it transmits at a much greater speed than the conventional pulse formats, since it uses DTMF (touch-tones) instead of pulses to transmit the data and it always sends a parity digit. Its main advantage over all the other formats is its large number of event codes (see tables below) with the ability to pinpoint an event (alarm, trouble, bypass, restore, etc.) to a specific zone (up to 48 zones in this system) and to report openings/closings for many users. For some reporting codes, the first of the two programmable digits determines the PID Event code to be transmitted. Other reporting codes transmit a dedicated PID Event code regardless of the digit programmed in the first location. In both cases, if transmissions are not desired, then program AA in locations 1 & 2. Refer to the following tables to select the PID Event codes to be transmitted.
Digit A B C D BURGLARY ZONE TYPES EVENT ENGLISH OUTPUT AT CODE CS RECEIVER 122 Silent Panic 123 Audible Panic 130 Burglary 131 Perimeter 132 Interior Hour Alarm 134 Entry/Exit 135 Day/Night 136 Outdoor 137 Tamper 140 General Alarm 144 Sensor Tamper 155 Foil Break 156 Day Trouble Digit A B C D E F FIRE ZONE TYPES EVENT ENGLISH OUTPUT AT CODE CS RECEIVER 110 Fire Alarm 111 Smoke 112 Combustion 113 Water Flow 114 Heat 115 Pull Station 116 Duct 117 Flame 140 General Alarm Hour Non-Burg 158 High Temperature 159 Low Temperature 200 Fire Supervisory 201 Low H2O Pressure 202 Low COGate Valve Sensor

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

LIMITED WARRANTY

Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way, Syosset, New York 11791, warrants its product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturers date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product(s) which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.

Technical Support Step-By-Step

Created on 05/17/05

How to Disable the Listen in Circuitry.
Since the DSL signal will interfere with the AMD (Answering Machine Defeat) circuitry in FBII panels and cause erroneous operation of the security equipment, you must only use a separate telephone line or a split installation. If these options are not feasible you may disable the Listen-in circuitry on the FBII panel. To disable the circuit, power the system down and cut one leg of the resistor indicated for the panel and lift it to a vertical position. Be careful that you dont damage any other component on the board, and the cut resistor does not touch other components. It is not advised to remove this resistor; this way it may be reconnected in the future if ever needed.

Cut Here

Figure 1 NOTE: The security dealer must check the system completely after the DSL installation is completed. Testing should be done to make sure that signals are received properly at the central station, and that downloading, if used, can be performed without problems. XL-2 Cutting the R74 resistor on board will stop the panel from listening for the warble tones. XL-21/XL-2S Cutting the R73 resistor on board will stop the panel from listening for the warble tones. XL-2P The feature cannot be disabled on this panel except by changing the Ring Count to ZERO. XL-2T Cutting the R25 resistor on board will stop the panel from listening for the warble tones. NOTE: With Revision 2.5, Q13 digit L2 with a value of +8 will also disable the Listen-in Circuit. XL-31 Cutting the R74 resistor on board will stop the panel from listening for the warble tones. XL-4/XL-4C Cutting the R59 resistor on board will stop the panel from listening for the warble tones. XL-20 Cutting the R20 resistor on board will stop the panel from listening for the warble tones. NOTE: Making this change will not affect the operation of the control panel, except to disable Answering Machine Defeat, whether it is installed with DSL or not.