Avoid touching exposed blades under Confetti-Cut shredder head.
The socket-outlet shall be installed near the equipment and shall be easily accessible.

ESPAOL ESPAO ESPA AOL

Modelo DS-12Cs DS-12C
Interruptor de desconexin de la energa Interruptor de transferencia de mando de SafeSense SafeSense

OPERATION

Cabezal de la destructora Consulte las instrucciones provistas ms abajo Sobrecalentado (rojo) En espera (verde) Tecnologa SafeSense (amarillo) Entrada del papel Interruptor de control
Encendido automtico ( I ) Apagado Retroceso (R)
Continuous operation: 5-minute maximum NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 4-5minutes will trigger 20-minute cool down period.
Press Auto-On ( I ) Set to Off (O)
Feed into paper entry and release Set to Off

Press Auto-On ( I )

Hold credit card at edge
Feed into center of entry and release

Ventana

TROUBLESHOOTING
Paper jam: Set to Off and empty basket. Replace basket and follow any or all of the below procedures.
Shredder doesnt start: Yellow - SafeSense active Yellow flashing - SafeSense w not active Make sure control switch is in Auto-On ( I ) position Set to Reverse (R) Alternate slowly back and forth Set to Off (0) Pull uncut paper from paper entry Set to Reverse (R) Wait 20 minutes for red light to turn off
Papelera extrable Tecnologa de seguridad innovadora! SafeSense detiene la destruccin cuando las manos estn demasiado cerca de la abertura.
Para probar la tecnologa SafeSense
La destructora viene completamente armada. Retire el envoltorio de la cesta y enchfela. Para operar la destructora, el interruptor de desconexcin de la energa debe estar en la posicin de encendido (I). Se enciende el sensor rea de prueba de tacto Presione Encendido automtico ( I )
ATTENTION: If the SafeSense light remains on, you must engage the SafeSense feature. (See SafeSense instructions below.)
Override Switch in order to perform steps above. Once the jam is cleared, reset the

Set to Off (0)

*Apply oil across entry

Shred one sheet

Set to Reverse (R) 2-3 seconds
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250

WARRANTY

LIMITED WARRANTY Fellowes, Inc. (Fellowes) warrants the cutting blades of the machine to be free from defects in material and workmanship for 5 years from the date of purchase by the original consumer. Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 1 year from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer.
Evite tocar las cuchillas expuestas debajo del cabezal de la destructora para el corte cruzado.
La toma del enchufe debe instalarse cerca del equipo y en un lugar al que pueda accederse con facilidad.
FRANCAIS FRANCAI FRANCA FRANC FRAN FRA FR NCAIS

Modle DS-12Cs DS-12C

Interrupteur dalimentation Interrupteur de neutralisation SafeSense Tte dchiqueteuse Consultez les instructions de scurit ci-aprs Surchauffe (rouge) Interrupteur En attente (vert)
Mise en marche automatique ( I ) Arrt Marche arrire (R) Inactif

EMPLOI

PAPIER
Technologie SafeSense (jaune) Entre de papier
Opration en continu : 5 minutes maximum REMARQUE : la dchiqueteuse fonctionne un peu aprs chaque passage pour dgager lentre. Une utilisation continuelle dune dure suprieure minutes dclenchera une priode de refroidissement de 20 minutes.
marche automatique ( I ) Rglez lappareil sur Arrt (O)
Alimentez lentre de papier et laissez aller Rglez Arrt
Appuyez sur la Mise en marche automatique ( I )
Tenez le bord de la carte de crdit

Useful Phone Numbers

DS-16Ci

Help Line

Australia Canada +1-800-33-11-77 +1-800-665-4339 Europe Mexico United States 00-800-1810-1810 +1-800-234-1185 +1-800-955-0959

Fellowes

Australia Benelux Canada Deutschland Espana France Italia +61-3-8336-9700 +31-(0)-76-523-2090 +1-905-475-6320 +49-(0)-5131-49770 +34-91-748-05-01 +33-(0)-1-30-06-86-80 +39-071-730041 Japan Korea Malaysia Polska Singapore United Kingdom United States +81-(0)-3-5496-2401 +82-(0)-2-3462-2844 +60-(0)-35122-1231 +48-(22)-771-47-40 +65-6221-3811 +44-(0)-1302-836836 +1-630-893-1600
Please read these instructions before use. Do not discard: keep for future reference.
1789 Norwood Avenue, Itasca, Illinois 60143-1095 USA 630-893-1600

fellowes.com

Polska Singapore United Kingdom United States
Australia Australia Benelux

Canada China

Deutschland Espaa Espaa

France Italia

Japan Korea
2008 Fellowes, Inc. Part No. 403484

WARRANTY

Our promise to you is quite simple. Fellowes shredders are built stronger, engineered to run longer, resist jams and power through large jobs. The Fellowes worry free warranty described below covers the performance of the product, provides for prompt service and support, plus a lifetime cutter warranty. Limited Warranty: Fellowes, Inc. (Fellowes) warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 2 years from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for the lifetime of the shredder. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer.

DATE OF PURCHASE

SERIAL NUMBER
Serial Number is located on inside of cabinet.

Serial Number

ENGLISH
A. SafeSense Technology B. Paper entry C. See safety instructions D. CD/Card flap E. Pullout bin F. Casters G. Disconnect power switch H. Power controls I. SafeSense override switch J. Overheat (red) K. Bin open (red) L. Bin full (red) M. Remove Paper (red) N. SafeSense indicator (yellow) O. Sheet capacity indicator P. Auto correcting button (blue) Q. Reverse R. On/off (blue) S. Forward

Model DS-16Ci

CAPABILITIES
Will shred: Paper, credit cards, CD/DVDs, staples and small paper clips Will not shred: Adhesive labels, continous form paper, transparencies, newspaper, cardboard, large paper clips, laminates, file folders, X-rays or plastic other than noted above Paper shred size: Cross-Cut...5/32 x 1-1/2 (3.9 x 38mm)
Maximum: Sheets per pass.... 16* CDs/Cards per pass... 1* Paper entry width...9/230mm *8.5x11, 20lb., (75g) paper at 120V, 60 Hz, 5Amps; heavier paper, humidity or other than rated voltage may reduce capacity. Recommended daily usage rates: 50100 shredding passes per day, 50 credit cards; 10 CDs. 16 sheets per pass.
Fellowes SafeSense shredders are designed to be operated in home and office environments ranging between degrees Fahrenheit (degrees Celsius) and 40 80% relative humidity.
ADVANCED PRODUCT FEATURES
Jam Proof System Eliminates frustrating jams by preventing overloads and powering through misfed paper. TECHNICAL EXPLANATION Sheet capacity indicator tells you when you have too many sheets or too few to maximize productivity
Patented SafeSense Technology Stops shredder immediately when hands are too close to the paper entry. TECHNICAL EXPLANATION
SilentShred Technology SilentShred noise quality shreds without noisy disruptions. TECHNICAL EXPLANATION SilentShred motor features whisper-quiet, efficient shredding performance without the noisy disruptions

AUTO AUTO

Shredder will stop automatically and indicator will light up when hands are too close to the paper entry.
Shredder will not operate when too many sheets are fed into paper entry (red light). Reduce sheet quantity and refeed If misfed, shredder will automatically adjust to power through or reverse out paper
Shredder will resume normal operation when hands are no longer near the paper entry.
Flashing indicator warns when SafeSense technology has been shut off
IMPORTANT SAFETY INSTRUCTIONS Read Before Using!
Keep away from children and pets. Keep hands away from paper entry. Always set to off or unplug when not in use. Keep foreign objects gloves, jewelry, clothing, hair, etc. away from shredder openings. If object enters top opening, switch to Reverse ( ) to back out object. Never use aerosol products, petroleum based lubricants or other flammable products on or near shredder. Do not use canned air on shredder. Do not use if damaged or defective. Do not disassemble shredder. Do not place near or over heat source or water. This shredder has a Disconnect Power Switch (G) that must be in the ON (I) position to operate shredder. In case of emergency, move switch to OFF (O) position. This action will stop shredder immediately. Avoid touching exposed cutting blades under shredder head. Rotate CD flap entry for shredding CDs/cards. Keep finger away from CD hole. Jam Proof System is disabled when flap is in CD position. Do not put foreign objects in paper entry. The grounded socket-outlet shall be installed near the equipment and shall be easily accessible.

AN NO SOLUCION EL PROBLEMA?
Fellowes est comprometido a proporcionar a los clientes el soporte tcnico y el servicio que merecen. Es por esto que ofrecemos varias opciones para que encuentre informacin tcnica, asistencia paso a paso y atencin personal. www.fellowes.com posee una amplia seccin de soporte tcnico en lnea, adems de una serie de opciones de autoservicio Nuestros profesionales de servicio al cliente estn dedicados a solucionar cualquiera de sus problemas Vaya a la seccin de soporte tcnico (Support) de www.fellowes.com o consulte la contraportada del manual para conocer nmeros de telfono tiles.
Model DS-16Ci SAFESENSE TECHNOLOGY OPERATION
Stops shredder immediately when hands are too close to the paper entry.
SET-UP AND TESTING FLASHING INDICATOR
BASIC PRODUCT MAINTENANCE AND TROUBLESHOOTING OILING SHREDDER
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE

*Apply oil across entry

Press and hold forward ( ) 2-3 seconds *Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250

Press forward

Shred one sheet
Turn the shredder ON ( ) to activate SafeSense
Touch test area and look for the SafeSense indicator to illuminate
SafeSense is active and working properly
SafeSense is deactivated when indicator is flashing
Shift override switch to the active position, reactivating SafeSense
Confirm the indicator is no longer flashing and retest by putting your hand on the test area
All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin.
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry).

TO CLEAN THE SENSORS

ADVANCED PRODUCT FEATURE MAINTENANCE AND TROUBLESHOOTING JAM PROOF SYSTEM *
Eliminates frustrating jams by preventing overloads and powering through misfed paper.

DISABLING THE FEATURE

Turn off and unplug shredder

Lift CD flap.

Locate Auto-start infared sensor.
Dip cotton swab in rubbing alcohol.
Using cotton swab, wipe away any contamination from the paper sensors.
PREVENTIVE MAINTENANCE AND MISCELLANEOUS TROUBLESHOOTING
If jam occurs, press and hold forward ( ) key until the document is completely through the shredder If not cleared, press reverse ( ) briefly (repeat steps 4 and 5 until shredded) If steps 4 and 5 do not clear jam, reverse paper all the way out, remove several sheets and refeed Run shredder once a day in reverse for 15 seconds to clear cutters Empty wastebasket when bin full indicator light is illuminated using bag # 36052 Shredder will not function if the pull-out bin is not pushed all the way in, or if bin needs to be emptied. When shredding for a prolonged period of time, the motor can become warm and require a cool down period. When this occurs the overheat indicator will alert you to the problem, this model will require 30 minutes to cool down.
Should you choose to disable the system, press and hold the auto button (blue) and reverse ( ) key at the same time
Once disabled, the blue Auto light is no longer illuminated (To re-engage, repeat step 1)
Shredding can continue with the system disabled, however a paper jam may occur with too many sheets and Remove Paper icon ( ) will illuminate
*100% Jam Proof when used in accordance with user manual

SAFESENSE TECHNOLOGY

ACCESSORIES
Maintenance is an important part of protecting your investment. Dont forget oil and shredder bags.
Shredder oil #35250 Should the SafeSense indicator stay lit without touching the opening The shredder will stop and SafeSense will need to be deactivated To deactivate, shift override switch to the not active position Once deactivated, the indicator will flash and the SafeSense feature will not function To clear paper, press and hold forward ( ) key until paper is shredded Once the paper is cleared, reactivate the SafeSense feature (To re-engage, see Operations)
DS-16Ci Shredder plastic bag #36052
PROBLEM STILL NOT SOLVED?
Fellowes is committed to giving our customers the support and service they deserve. That is why we offer several options for you to find technical information, step-by-step assistance and personal attention. www.fellowes.com features an extensive on-line support section with a number of self-service options Our customer service professionals are dedicated to resolve any of your issues Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.