)$&)$&&1 )$&3)$&3&1

6HFXULW\6\VWHPV

8VHUV*XLGH

K5309-5 7/01 1

IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Central Monitoring Station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in reducing fire deaths in the United States. With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72). These recommendations can be found on page 43 of this manual.

$ERXW7KLV0DQXDO

This manual is a step-by-step guide that will acquaint you with the system's features and benefits. It defines the components and their functions, describes their operation, and provides clear step-by-step instructions for normal and emergency procedures. Keep this manual in a convenient place so that you can refer to it as necessary.

7DEOHRI&RQWHQWV

System Overview.... 5 Introduction.... 5 System Basics.... 5 About The Keypads.... 8 General Information.... 8 Functions of the Keypads.... 10 Entry/Exit Delays..... 12 Exit Delay.... 12 Entry Delay.... 12 Exit Alarms.... 13 Checking For Open Zones... 13 Using the [] Key.... 13 Arming the System.... 14 Stay Mode: Arms Perimeter Only, Entry Delay On.. 14 Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones.. 14 Instant Mode: Arms Perimeter Only, Entry Delay Off.. 14 Away Mode: Arms Entire System, Entry Delay On.. 14 Arming Commands.... 15 Single Button Arming.... 16 Single-Button Step Arming... 16 Using the Keyswitch...17 Using the Keyswitch.... 17 Disarming and Silencing Alarms... 18 Using the [OFF] key.... 18 Bypassing Protection Zones.... 19 Using the BYPASS Key.... 19 Quick Bypass..... 20 Chime Mode..... 20 Viewing Current Date and Time... 21 Viewing the Current Date and Time... 21 Setting the Date and Time.... 21 Panic Keys.... 22 Using Panic Keys.... 22 3
Macro Key Programming & Usage... 23 About Macro Keys.... 23 Example of Macro Programming.... 24 Using a Programmed Macro Key.... 24 Using Device Commands.... 25 Paging Feature.... 26 About Automatic Paging.... 26 Single Button Paging.... 27 Latch Key Paging.... 27 Security Codes & Authority Levels.... 28 About Security Codes.... 28 Authority Level Definitions.... 28 To assign User Codes and Attributes... 29 Accessing Other Partitions (GOTO Command and Multi-Partition Arming). 30 About Accessing Partitions... 30 Using the GoTo Command.... 31 Multi-Partition Arming.... 31 Common Zone Operation.... 32 Scheduling..... 33 About Scheduling.... 33 Creating Schedules.... 33 Event Logging Procedures.... 35 About Event Logging.... 35 Viewing the Event Log... 35 Testing the System (To Be Conducted Weekly).. 36 Trouble Conditions.... 37 Maintaining Your System.... 40 Fire Alarm System (If Installed).... 41 Quick Guide to Basic System Functions.. 45 Summary of Audible/Visual Notifications... 46 Regulatory Statements and Warnings... 48 Charts of Your System's Features... 50

6\VWHP2YHUYLHZ

,QWURGXFWLRQ
Congratulations on your ownership of a First Alert Professional Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today. This system provides: Three forms of protection: burglary, fire* and emergency At least one keypad which provides control of system and displays system status Various sensors for perimeter and interior burglary protection Smoke or combustion detectors* designed to provide early warning in case of fire. Your system may also have been programmed to automatically send alarm or status messages over the phone lines to a Central Monitoring Station. * Commercial installations and some residential systems may not include fire protection check with your installer. NOTE: The features and procedures described in this manual apply to both the FA168C and FA148CP security systems. Differences are noted where applicable.

7 INSTANT Arms in manner similar to the
Disarms burglary portion of the 12.
STAY mode, but without the entry delay feature. Entering via an entry/exit door will cause an alarm.
system, silences alarms and audible trouble indicators, and clears visual display after problem's correction. 3. Arms the entire burglary system, perimeter and interior.

3 STAY 2 AWAY

Used to display all open protection
zones. 13. FUNCTION KEYS: Keys A, B, C, D may have been programmed for a variety of functions, including panic (emergency) functions. For details, see the Function Keys section. 14.

4 MAXIMUM

Arms perimeter portion of burglary
system only. Interior protection is not armed, allowing movement within premises without causing an alarm. 5.

Arms the entire burglary

Tests the system and alarm
sounder if disarmed. Refer to Testing The System section for test procedures. 6.
6 BYPASS Removes individual protection
system, perimeter and interior, but without entry delay feature. Entering via an entry/exit door will cause an alarm. 15. INTERNAL SOUNDER: The built-in sounder mimics the alarm sounder during alarms, and will also "beep" during certain system functions. 16. READY INDICATOR: (GREEN) Lit when the system is ready to be armed (no faults present). While the system is disarmed, this indicator will go on and off as protection zones are closed and opened. 17. ARMED INDICATOR: (RED) Lit when the system has been armed.
zones from being monitored by the system. 7.

9 CHIME

Turns CHIME mode on and off.
When on, the opening of windows or doors while the system is disarmed will sound 3 beeps at the keypad(s). 8.
This key can be used for "Quick
Arming" of the system without use of a security code (if programmed).
)XQFWLRQVRIWKH.H\SDGV&RQWLQXHG
1 OFF 4 MAX 7INSTANT 2 AWAY 5 TEST 8 CODE STAY 6 BYPASS 9 CHIME #

FA168C-001-V0

(Keypad shown without swing-down front door)
(Keypads shown with typical function key labels) IMPORTANT! When entering codes and commands, sequential key depressions must be made within 4-5 seconds of one another. If 4-5 seconds elapse without a key depression, the entry will be aborted and must be repeated from its beginning. Be sure to observe this precaution when performing any of the procedures in this manual. If you make a mistake while entering a security code, stop, press the [] key, and then start over. If you stop in the middle while entering a code, and then immediately start the entry over, an erroneous code might be entered.

(QWU\([LW'HOD\V

Your system has preset time delays, known as exit delay and entry delay.

([LW'HOD\

Exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after arming your system in any arming mode and Alpha Display keypads display the message You May Exit Now. When You may exit now disappears, the system is fully armed. If programmed, a slow beeping will sound during the exit delay period until the last 5 seconds, which then changes to fast beeping (alerting you to the end of exit delay). If you cannot leave by this time, you should stop, disarm the system, and start over to avoid a false alarm.
Exit Delay Restart. If you wish to open the entry/exit door to let someone in after arming STAY, you can re-start the exit delay at any time simply press the [] key, then let that person in. The system automatically re-arms when exit delay expires, which avoids having to disarm the system and then re-arm it again. In addition, when the system is armed AWAY, re-entering the premises (e.g., forgot a wallet) through the entry/exit door before exit delay time expires will reset the exit delay time.

(QWU\'HOD\

Entry Delays give you time to disarm the system when you re-enter through the designated entrance door. You must disarm the system before the entry delay period ends, or an alarm will occur. The keypad beeps during the entry delay period, reminding you to disarm the system. There are two entry delays (if programmed). The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to walk to the keypad to disarm the system. You can also arm the system with no entry delay at all by using the INSTANT or MAXIMUM arming mode. This mode provides greater security while on the premises or while away for extended periods of time. See your installer for your delay times. Partition 1 ___________________________________________________________ Exit Delay: seconds Entry Delay 1: Entry Delay 2: seconds seconds
NOTE: Entry/Exit times set for partition 1 also apply to the common zone (FA168C).
Partition 2 (FA168C) _________________________________________________ Exit Delay: seconds Entry Delay 1: Entry Delay 2: seconds seconds
(QWU\([LW'HOD\V&RQWLQXHG

([LW$ODUPV

Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the message "CANCELED ALARM" or "CA" is displayed on the keypad, along with a zone number indicating the faulted zone. No message is sent to the Central Monitoring Station. To clear the exit alarm condition, the open zone must be made intact; to clear the display, enter your code plus OFF. If you do not disarm the system before the entry delay ends, and an entry/exit door or interior zone is still open, the alarm sound continues and an "exit alarm" message is sent to the Central Monitoring Station. The message ""EXIT ALARM" or "EA" is displayed on the keypad, along with a zone number indicating the faulted zone. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time. An exit alarm also results if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay.

0D[LPXP0RGH$UPV(QWLUH6\VWHP(QWU\'HOD\2II
Used when leaving the premises for extended periods (e.g., vacation). Arms same as Away mode, but entry delay is off. An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.

$UPLQJ&RPPDQGV

Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is displayed. Mode

Press these keys

security code + [3] (STAY)

Keypad Confirms By

three beeps armed STAY message displayed red ARMED indicator lights three beeps NIGHT-STAY message displayed red ARMED indicator lights three beeps armed STAY message displayed red ARMED indicator lights Note that entry delay is turned off. two beeps, or, if programmed, beeping for duration of exit delay armed AWAY message displayed red ARMED indicator lights Leave the premises through an entry/exit door during the exit delay period to avoid causing an alarm. The keypad beeps rapidly during the last 5 seconds of the exit delay to warn you that it is ending. same as Away (described above) Note that entry delay is turned off.

Night-Stay

security code + [3] + [3]

Instant

security code + [7] (INSTANT)
security code + [2] (AWAY)

Maximum

security code + [4] (MAXIMUM)
Quick Arming If "Quick Arming" was programmed by the installer, the [#] key can be pressed in place of the security code when arming the system. However, the security code must always be used to disarm the system. Function Key Arming For any arming command, a function key may have also been programmed for your system. If so, you can press and hold the appropriate function key for 2 seconds to arm the system. See your installer for the designated functions (see Single Button Arming section). Refer to the Accessing Other Partitions section for information on multi-partiion arming (FA168C).

6LQJOH%XWWRQ$UPLQJ

The A, B, C, and/or D keys on your keypad may have been programmed for single-button arming. Note that while it will not be necessary to use a security code for arming, a security code must always be used to disarm the system. If Single-Button Arming is programmed: A function key has been assigned to a specific type of arming: STAY mode, Night-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming paragraph). You DO NOT need to enter your user code before pressing the function key (you always need your user code to DISARM the system). Before arming, close all perimeter doors and windows. 1. Press and hold the assigned function key for 2 seconds (no code is required). Function keys are shown below.

(-7%61)( 6)%(= 83 %61

Fixed-Word Display: READY

INSTANT

ADT3000-007-V0
2. The keypad begins beeping and displays the armed message. The red ARMED indicator also lights.
%61)(%;%= =39 1%= )<-8 23;

Fixed-Word Display: AWAY

6WHS$UPLQJ)HDWXUH
Single-Button Step arming may have been programmed into one of the lettered keys (A, B, C, or D). Check with your installer to see if this has been done in your system. If Step-Arming is programmed: The assigned key provides a choice of three levels of security. The selected key can be pressed once, twice, or three times, increasing the level of security with each press, as follows Key First Press Second Press Third Press

A, B, C, D

Armed-STAY
Armed Night-STAY (if programmed)

Armed-AWAY

8VLQJWKH.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming. Red and green lights on the keyswitch plate indicate the status of your system as follows: Green Light: Lights when the system is disarmed and ready to be armed (no open zones). If the system is disarmed and the green light is off, it indicates the system is not ready (one or more zones are open). Red Light: Lights or flashes when system is armed in AWAY or STAY mode. See your installer for the meanings of the lit red light: Lit Steady = system armed AWAY or system armed STAY and exit delay has expired Flashing = system armed STAY and exit delay timer active Rapid flashing = an alarm has occurred (memory of alarm). Before arming, close all perimeter doors and windows. To arm in the AWAY mode: Turn the key to the right for 1/2 second and release. Keypads beep twice and the red indicator lights or flashes. To arm in the STAY mode: Turn the key to the right and hold for longer than 1 second, then release. Keypads beep three times and the red indicator lights or flashes. To disarm the system: Turn the key to the right and release. The red light turns off

GREEN RED

'LVDUPLQJDQG6LOHQFLQJ$ODUPV

8VLQJWKH>2))@NH\

The OFF key is used to disarm the system, silence alarm and trouble sounds, and clear alarm memories.
IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence. LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.

(Security Code)

The READY indicator light will be lit if all zones are secure, and the keypad will emit a single tone to confirm that the system is disarmed.
2. To Silence a Burglary Alarm and Clear a Memory of Alarm Enter your security code and press the OFF key to silence the alarm (or warning tones of a Memory of Alarm). Note the zone in alarm on the keypad display, and make that zone intact (close door, window, etc.). Now enter the security code plus OFF sequence again to clear the keypads Memory of Alarm display. 3. To Silence a Fire Alarm and Clear Memory of Alarm Simply press the OFF key to silence the alarm. Then enter the security code plus OFF sequence to clear the keypad's Memory of Alarm display. See the Fire Alarm System section.

%\SDVVLQJ3URWHFWLRQ=RQHV

8VLQJWKH%<3$66.H\
Use this key when you want to arm your system with one or more zones intentionally unprotected.
Vent Zones: Your system may have certain windows set as vent zones, which are automatically bypassed if left open when arming the system (you do not need to manually bypass them). However, if a vent zone window is closed after arming, it becomes protected and will cause an alarm if opened again while the system is armed. When bypassing zones: The system must be disarmed before you can bypass zones. Bypassed zones are unprotected and will not cause an alarm if violated. The system will not allow fire zones to be bypassed. Zones are automatically unbypassed when the system is disarmed. 1.
6 + zone numbers (see below)
Fixed-Word Display: NOT READY Alpha Display:
Enter the 2-digit zone number(s) for the zone(s) to be bypassed (e.g., 06, 10, 13, etc.). Single digit zone numbers must be preceded by a zero (e.g. 05, 06). 2. When finished, the keypad will momentarily display a "Bypass" message for each bypassed zone number. Wait for all bypassed zones to be displayed. Arm the system as usual. When armed, the arming message is displayed with ZONE BYPASSED. To display bypassed zones prior to arming, enter your security code and press the [6] BYPASS key.
(-7%61)( &=4%77 6)%(= 83 %61
Fixed-Word Display: BYPASS
%61)( 78%= >32) &=4%77)(
Typical armed alpha display after bypassing zones.

4XLFN%\SDVV

If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. This feature is useful if, for example, you routinely leave certain windows open when arming at night. 1.

+ 6 + [#]

Fixed-Word Display: NOT READY
In a few moments, all open zones will be displayed and automatically bypassed. Make sure that only those
zones that you wish to leave unprotected are bypassed, and that there are no other zones unintentionally left open.
2. Wait for all bypassed zones to be displayed, then arm the system as desired. Ask your installer if "Quick Bypass" is active for your system, and if so, check here:

7)0)'8 1%'63

1%'63 (-740%=

1%'63 4+1

0DFUR.H\3URJUDPPLQJ8VDJHFRQW
The keypad beep to acknowledge your input and displays the command you entered (followed by F). 4. Enter the next command, followed by press/holding the D key for at least two seconds. The keypad beeps and displays the keystrokes entered so far. 5. Repeat until the all the desired commands (up to 16 characters including the Fs) have been entered. Be sure to check your keystrokes before continuing. If you made a mistake, you must start over. 6. To exit, press/hold the D key for at least two seconds. The display returns to system status and indicates system is ready.
Typical Macro Alpha Display:
([DPSOHRI0DFUR3URJUDPPLQJ
Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an exterior light, and then (3) arm the security system in the AWAY mode. The procedures in the table that follows show you how you would program this macro:
Function 1. Bypass zones 02 & 03 2. Insert terminator. 3. Turn light on (device 01). 4. Insert terminator. 5. Arm system AWAY 6. Insert terminator.

Keystrokes Required

Press BYPASS [6] key, then 2-digit zone numbers 02 & 03. Press the D key for at least 2 seconds. Press [#] and 7 keys for device ON, and [01] key for selecting device 1. Press the D key for at least 2 seconds. Press AWAY [2] key. Press the D key for at least 2 seconds.

Keypad Display

* *# *#* *#* *#**

8VLQJD3URJUDPPHG0DFUR.H\

System must be disarmed before performing a macro function. 1. Press the Macro key programmed for the desired (-7%61)( series of commands for at least 2 seconds. The Enter 6)%(= 83 %61 User Code prompt appears. The prompt remains displayed for up to 10 seconds.

)28)6 97)6 '3()

2. Enter your 4-digit user code. The programmed macro sequence begins automatically after the user code is entered.

8VLQJ'HYLFH&RPPDQGV

$ERXW'HYLFH&RPPDQGV
Your system may be set up so that it can control certain lights or other devices. Some devices may be automatically turned on or off by the system. You may be able to override automatically controlled devices using the commands described below. Some devices can be manually turned on or off using the commands described below. See your installer for a list of devices that may be set up for your system. A list of these devices is provided at the back of this manual for you to fill out. To Activate Devices: + [#] + [7] + 2-digit device number

If the test mode is inadvertently left active, it automatically turns off after 4 hours.

7URXEOH&RQGLWLRQV

"Check" and "Battery" Displays The word CHECK on the keypad's display, accompanied by a "beeping" at the keypad, indicates a trouble condition in the system.
To silence the beeping for these conditions, press any key. 1. A display of "CHECK" and one or more zone numbers indicates that a problem exists with the displayed zone(s) and requires your attention. Determine if the zone(s) displayed are intact and make them so if they are not. If the problem has been corrected, the display can be cleared if you enter the OFF sequence (security code plus OFF key) twice. If the display persists, CALL FOR SERVICE. Note: A display of CHECK 70 on Alpha Display keypads indicates that the wiring connection to the external sounder is at fault (opened or shorted), and you should CALL FOR SERVICE. See BELL FAILURE on next page. A display of CHECK 90 indicates that RF interference may be impeding the operation of wireless sensors* in the system. See Rcvr Jam on next page. 2. If there are wireless sensors* in your system, the CHECK condition may also be caused by some change in the environment that prevents the wireless receiver from hearing a particular sensor. CALL FOR SERVICE if this occurs. IF YOU CANNOT CORRECT A "CHECK" DISPLAY, CALL FOR SERVICE.
TYPICAL "CHECK" DISPLAYS
* Not all systems use wireless sensors.

',)'/ &)(6331;-2(3;

ALPHA DISPLAY KEYPAD
FIXED-WORD DISPLAY KEYPAD
7URXEOH&RQGLWLRQV&RQWLQXHG
Words or letters in parentheses ( ) are those that are displayed on Alpha Display keypads.

Other Trouble Displays

* Any beeping that
accompanies a trouble display can be stopped by depressing any key on the keypad or by entering an OFF sequence (code + OFF)

COMM. FAILURE (or FC)

Indicates that a failure has occurred in the telephone communication portion of your system. CALL FOR SERVICE. Indicates that a low system battery condition exists. Display is accompanied by "beeping"* at the keypad. If this condition persists for more than one day (with AC present), CALL FOR SERVICE. Indicates that there is a low battery condition in the wireless transmitter** number displayed (00 is RF keypad). Accompanied by a single "beep"* (once every 40 seconds) at the keypad. Either replace the battery yourself, or CALL FOR SERVICE. If the battery is not replaced within 30 days, a CHECK display may occur. Wireless part of the system is experiencing RF interference which may impede reception from wireless sensors.** Indicates that the control is on-line with the Central Monitoring Station's remote computer. The control will not operate while on-line. Wait a few minutes the display should disappear. Indicates that the wiring connection to the external sounder is at fault (open or shorted). Accompanied by beeping at the keypad. CALL FOR SERVICE.

SYSTEM LO BAT (or BAT with no zone No.)

** Not all systems use

wireless sensors.
LO BAT + zone descriptor (or BAT with zone No.)

Rcvr Jam (or CHECK 90)

MODEM COMM (or CC)
BELL FAILURE (or CHECK 70)
Other Trouble Displays (Continued) AC LOSS (or NO AC) The system is operating on battery power only due to an AC power failure. If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. If AC power cannot be restored and a low system battery message appears (see previous page), CALL FOR SERVICE. Busy-Standby (or dI) OPEN CIRCUIT (or OC) Long Rng Trbl (or bF) If this message remains displayed for more than 1 minute, system is disabled. CALL FOR SERVICE. The keypad is not receiving signals from the control. CALL FOR SERVICE. If part of your system, back-up Long Range Radio communication has failed. CALL FOR SERVICE. The telephone line has a problem. CALL FOR SERVICE.
TELCO FAULT (or CHECK 94)
Total Power Failure If there is no keypad display at all, and the READY indicator
is not lit, operating power (from AC and back-up battery) for the system has stopped and the system is inoperative. CALL FOR SERVICE.
In The Event Of Telephone Operational Problems
In the event of telephone operational problems, disconnect the control from the phone line by removing the plug from the phone wall jack. We recommend that your installer demonstrate this disconnection on installation of the system. Do not attempt to disconnect the phone connection inside the control. Doing so will result in the loss of your phone lines. If the regular phones work correctly after the control has been disconnected from the phone wall jack, the control has a problem and you should immediately call for service. If upon disconnection of the control, there is still a problem on the phone line, notify the Telephone Company that they have a problem and request prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the security system. Repairs must be made only by authorized service (see the LIMITED WARRANTY statement for information on how to obtain service).

0DLQWDLQLQJ<RXU6\VWHP

Taking Care of Your System
The components of your security system are designed to be as maintenance-free as possible. However, to make sure that your system is in reliable working condition, do the following: 1. Test your system weekly. 2. Test your system after any alarm occurs. You can silence the keypads warning tones by pressing the OFF key, but the keypad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your wireless sensors. When you replace the weak battery with a fresh one, the sensor sends a "good battery" signal to the control as soon as the sensor is activated (opening/closing of door, window, etc.), causing the low battery display to turn off. If the sensor is not activated, the display will automatically clear within approximately 1 hour. Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects a low battery in wireless sensors, including smoke detectors, the personal emergency transmitter, and the portable wireless keypad and displays a low battery message*. (A low battery in a portable wireless keypad is detected as soon as one of its keys is pressed, and displayed as 00.). Battery-operated smoke detectors with a low battery also emit a single "chirp" sound approximately once every 2030 seconds. Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 24 years of service. 3-volt lithium batteries provide up to 4 or more years of operation. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures or large swings in temperature, may all lead to the reduction of actual battery life in an installation. * The low battery message comes on as a warning that battery replacement

in indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low battery indication is still fully operational.
Silencing Low Battery Warning Tones at the Keypad
Replacing Batteries in Wireless Sensors
Wireless sensors may not have been used in your security system IMPORTANT: Use only batteries recommended by your installer as replacement.
Routine Care Treat the components of your security system as you would any other
electrical equipment. Do not slam sensor-protected doors or windows. Keep dust from accumulating on the keypad and all protective sensors, particularly on motion sensors and smoke detectors. The keypad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any other fluid on the units.
)LUH$ODUP6\VWHP,I,QVWDOOHG
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

General

Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Keypad(s) and any external sounders. A FIRE message will appear at your Keypad and remain on until you silence the alarm (see below for silencing fire alarms). * Temporal pulse sounding is produced for Fire alarms, as follows: 3 pulsespause3 pulsespause3 pulsespause. , repeated.
TYPICAL FIRE EMERGENCY DISPLAYS

*-6)1%78)6 &)(6331

ALARM FIRE

FIXED-WORD KEYPAD

Silencing Fire Alarms and Clearing Memory of Alarm
You can silence the alarm at any time by pressing the OFF key (the security code is not needed to silence fire alarms). To clear the display, enter your code and press the OFF key again (to clear Memory of Alarm).
2. If the Keypad's FIRE display does not clear after the second OFF sequence, smoke detectors may still be responding to smoke or heat producing objects in their vicinity. Investigate, and should this be the case, eliminate the source of heat or smoke. 3. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. When the problem has been corrected, clear the display by entering your code and pressing the OFF key.
Smoke Detector Depending on the type of smoke detectors in your system, it may be Reset necessary to "reset" the smoke detectors after a fire alarm has been
turned off. Check with your installer. This "reset" is accomplished at a keypad, as follows: Enter User Code*, then press the [1] key (* except arm only user).

Arms system in mode selected, quickly and without use of a code. Bypassed zones are unprotected and will not cause an alarm if violated. Bypasses all faulted zones automatically. Also disarms system. Memory of alarm remains until cleared. Memory of Alarm remains until cleared. Determine cause. Also silences sounders. Memory of alarm remains until cleared. Keypad beeps rapidly on entry if alarm has occurred while absent. Alarm display will remain upon disarming until cleared. Performs desired action and sends silent alarm to Central Station. See the Panic Keys section for emergency functions programmed for your system. Note: Keys A, B, and C may have been programmed for other functions. The keypad will sound if doors or windows are violated while system is disarmed and chime mode is ON.
Quick Bypass (if programmed) Silence Sounders Burglary: Fire: "Check": Disarm System Clear Alarm Memory
Enter code. Press OFF key. Press OFF key. Press any key. Enter code. Press OFF key. After disarming, enter code again. Press OFF key again.
Duress (if active and connected to Central Station) Panic Alarms (as programmed)
Arm or disarm "normally", but use your 4-digit Duress code to do so. Press key [A], [B], or [C] for at least 2 seconds.

Chime Mode

To turn ON or OFF: Enter code. Press CHIME key.
Test Mode Phone Access if applicable
To turn ON: Enter code. Press TEST key. Tests alarm sounder and allows sensors To turn OFF: Enter code. Press OFF key. to be tested. Consult Phone Access User's Guide that accompanies the Phone Module. Permits system access remotely, via Touch-tone phone.
6XPPDU\RI$XGLEOH9LVXDO1RWLILFDWLRQV

)L[HG:RUG'LVSOD\.H\SDGV

SOUND LOUD, INTERRUPTED* Keypad & Ext. LOUD, CONTINUOUS* Keypad & Ext. ONE SHORT BEEP (not repeated) Keypad only BURGLARY/AUDIBLE EMERGENCY ALARM a. SYSTEM DISARM b. SYSTEM ARMING ATTEMPT WITH AN OPEN ZONE. c. BYPASS VERIFY CAUSE FIRE ALARM DISPLAY FIRE is displayed; zone number of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed. ALARM is displayed. Zone number of zone in alarm is also displayed. a. READY indicator light comes on. b. Number of the open protection zone displayed. c. Zone numbers of the bypassed protection zones are displayed (one beep is heard for each zone displayed). Subsequently, BYPASS is displayed. a. Opened zone numbers will appear. b. BAT displayed with zone number of transmitter. AWAY is displayed. Red ARMED indicator is lit. a. STAY or INSTANT is displayed. Red ARMED indicator is lit. b. CHIME displayed; zone number of open protection zone will be displayed if the [] key is pressed. a. CHECK displayed. Zone number of troubled protection zone is displayed. b. FIRE or ALARM is displayed; zone number of zone in alarm is displayed

ONE SHORT BEEP (once every 40 secs) Keypad only TWO SHORT BEEPS Keypad only THREE SHORT BEEPS Keypad only
a. SYSTEM IS IN TEST MODE b. LOW BATTERY AT A TRANSMITTER ARM AWAY or MAXIMUM a. ARM STAY, NIGHT-STAY, OR INSTANT b. ZONE OPENED WITH SYSTEM IN CHIME MODE.
RAPID BEEPING Keypad only
a. TROUBLE b. MEMORY OF ALARM
c. BAT displayed with no zone ID number. c. SYSTEM LOW BATTERY d. EXT. SOUNDER WIRING FAIL d. CHECK 70 is displayed. SLOW BEEPING Keypad only a. EXIT DELAY WARNING b. ENTRY DELAY WARNING a. AWAY is displayed. b. Exceeding the entry delay time without disarming causes alarm.
* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.

$OSKD'LVSOD\.H\SDGV

SOUND LOUD, INTERRUPTED* Keypad & Ext. LOUD, CONTINUOUS* Keypad & Ext. ONE SHORT BEEP (not repeated) Keypad only CAUSE FIRE ALARM. DISPLAY FIRE is displayed; descriptor of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed. ALARM is displayed. If programmed, descriptor of zone in alarm is also displayed a. DISARMED/READY TO ARM is displayed. b. Number and descriptor of open protection zone is displayed. c. Numbers and descriptors of the bypassed zones are displayed (One beep is heard for each zone displayed). Subsequently, the following is displayed: DISARMED BYPASS /Ready to Arm. a. Opened Zone identifications will appear. b. LO BAT displayed with description of transmitter. ARMED AWAY or MAXIMUM displayed. Red ARMED indicator lit. a. ARMED STAY or ARMED INSTANT displayed. Red ARMED indicator lit. b. CHIME displayed, descriptor of open protection zone will be displayed if the [] key is pressed. a. CHECK displayed. Descriptor of troubled protection zone is displayed. b. FIRE or ALARM is displayed; descriptor of zone in alarm is displayed. c. SYSTEM LO BAT displayed.
BURGLARY/AUDIBLE EMERGENCY ALARM. a. SYSTEM DISARM. b. SYSTEM ARMING ATTEMPT WITH AN OPEN ZONE. c. BYPASS VERIFY.
a. SYSTEM IS IN TEST MODE. b, LOW BATTERY AT A TRANSMITTER. ARM AWAY or MAXIMUM. a. ARM STAY, NIGHT-STAY, OR INSTANT. b. ZONE OPENED WHILE SYSTEM IS DISARMED. a. TROUBLE. b. MEMORY OF ALARM.
c. SYSTEM LOW BATTERY. d. EXT. SOUNDER WIRE FAIL. d. BELL FAILURE is displayed. SLOW BEEPING Keypad only a. EXIT DELAY WARNING (if programmed). b. ENTRY DELAY WARNING.
a. ARMED AWAY OR MAXIMUM is displayed along with You May Exit Now. b. DISARM SYSTEM OR ALARM WILL OCCUR is displayed. Exceeding the delay time without disarming causes an alarm.
5HJXODWRU\6WDWHPHQWVDQG:DUQLQJV
NOTE: This is a Grade A Residential System
RADIO FREQUENCY EMISSIONS

List of Output Devices

( FA168C can use devices 01-16; FA148CP can only use devices 01-08; both can use trigger devices 17/18.) Description Schedule No. Function Key Device 17 18
/,0,7$7,2162)7+,66<67(0
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F, the detection performance can decrease. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

Applies to FA168C only.

For UL installation requirements, refer to the Installation Instructions for the 4204.

Address 11

4204 4204
DIP SWITCH FOR SETTING DEVICE ADDRESS AND ENABLING/DISABLING TAMPER COVER TAMPER (REED) SWITCH
RELAY 4 TYPICAL (SHOWN "OFF") RELAY
C NC NO C NC NO C NC NO C NC NO TB2

4-PIN CONSOLE PLUG RELAY

EITHER OR BOTH CAN BE USED TB16 YEL BLK GRN RED DATA IN FROM CONTROL () GROUND DATA OUT TO CONTROL (+) 12V RELAY
Figure 11. 4204 Connections to Control (4229 Module is shown in the 4219/4229 Expansion Zones paragraph on page 2-7)
Powerline Carrier Devices
1. Install the powerline carrier devices according to the instructions included with each. FA168C: Up to 16 devices (if no relays are used) FA148CP: Up to 8 devices (if no relays are used) 2. Use Programming Mode to enter the device house ID in data field*27, and enter the unit code using *79 Output Device menu Mode. See connections diagram in the AC Wiring paragraph for connecting the 4300/1321X10 transformer.
When using Powerline Carrier devices, you must use a 4300 or 1321X10 Transformer instead of the 1321 Transformer. The 4300/1321X10 Transformer provides AC power to the control panel, and also supplies signals from the control panel through the premises AC wiring to the Powerline Carrier devices (which are plugged into AC outlets). You can then make devices that are plugged into Powerline Carrier devices perform various functions in response to commands you enter at the security system keypads.
Powerline Carrier devices and the 4300 Transformer are not UL Listed for fire or burglary functions and are intended for home automation.

On-Board Triggers

Connect field wiring to the desired trigger pin on the 8-pin trigger connector centrally located above the terminal strip. If using 1321X10 transformer and powerline carrier devices, use the SA4120XM-1 cable. See Wiring the AC Transformer section for transformer connections. If only using the on-board triggers, you can use a standard keypad cable as shown below.
There are two on-board triggers that can be used to activate output devices. Program these triggers using *80/*81 Menu modes as you would for any other relay output. When using these outputs, note: pin 1 = output number 17 (trigger 1): 56 ohms to ground when closed; open when off; (can support 12V relay module that draws less than 40mA) pin 5 = output number 18 (trigger 2): 100 ohms to ground when closed; open when off; (can support 12V relay module that draws less than 20mA)

Entering Interactive Mode Press [] + [Interactive Mode No.] (for example, 56) while in Program Mode. The Alpha display keypad will display the first of a series of prompts requesting entries. After making the appropriate entry, press the [] key to accept the entry and continue to the next prompt.
Loading Factory Defaults/Initializing for Download
To Load Default Entries Press 97 while in Program Mode. This resets all data fields to the default values shown in the boxes in the Program Form. Use 97 only if you wish to return to the original factory-programmed defaults. Press 96 while in Program Mode. This initializes the system for downloading and resets all the subscriber account numbers and CSID.
To Initialize Download ID
Do not press 97 to load defaults if any programming has been done previouslydata already programmed into the system will be changed! Exiting the Programming Mode
Prevent installer code reentry Press 98. Exits Programming Mode and prevents re-entry by: Installer Code + [8] + [0] + [0]. To enter the programming mode if 98 was used to exit, you must first power the system down. Then power up again, and press [] and [#] at the same time, within 50 seconds of powering up, UNLESS Local Lockout is enabled (field *91). If so, re-entry to programming mode is permitted only by Installer code + [ 8] + [0] + [0]. Press 99. Exits Programming Mode and allows re-entry by: Installer Code + [ 8] + [0] + [0] or by: Pressing [] and [#] at the same time, within 50 seconds of power-up.
Allow installer code reentry
Table of Device Addresses
Address 28 Report Device 100 RF Receiver 115 n/a n/a n/a n/a n/a n/a n/a n/a n/a Long Range Radio FA4286 Voice Module Zone Expanders (4219/4229): module 1 zones 09 - 16 module 2 zones 17 - 24 module 3 zones 25 - 32 module 4 zones 33 - 40 module 5 zones 41 - 48 Relay Modules (4204): module 1 module 2 module 3 module 4 Keypads: keypad 1 keypad 2 keypad 3 keypad 4 keypad 5 keypad 6 keypad 7 keypad 8 5800TM Module Programmed by *56 zone programming: input device type entry automatic if output to long range radio field *29 enabled automatic if phone module access code field *28 enabled *56 zone programming: input device type entry, then: automatic if zone no. 9-16 entered as AW type or relay assigned automatic if zone no. 17-24 entered as AW type or relay assigned automatic if zone no. 25-32 entered as AW type or relay assigned automatic if zone no. 33-40 entered as AW type or relay assigned automatic if zone no. 41-48 entered as AW type or relay assigned *79 output device programming: device address prompt: entered at device address prompt entered at device address prompt entered at device address prompt entered at device address prompt data field programming as listed below: always enabled for partition 1, all sounds enabled. data field *190 data field *191 data field *192 data field *193 data field *194 data field *195 data field *196 automatic

4219/4229 addresses 9-11 and 4204 addresses 14-15 apply to the FA168C only. Addressable devices are identified by 1 plus the device address when reporting. Enter a report code for zone 91 to enable addressable device reporting (default = reports enabled). See field *199 for addressable device (ECP) 3-digit/2-digit identification keypad display options. 3-6

Data Field Programming

About Data Field Programming
The following pages list this controls data fields in numerical order. Field numbers are listed in the left column followed by a Title and Data Entries column, which lists the valid entries for each field. Experienced installers can simply follow this column when programming the data fields. The Explanation column provides explanatory information and special notes where applicable. Use the blank programming form to record the data for this installation.

Programming Data Fields

Data field programming involves making the appropriate entries for each of the data fields. Start Data Field programming by entering the installer code + 8 + 0 + 0.
System Setup Fields (20 29)
FIELD TITLE and DATA ENTRIES Installer Code

Enter 4 digits, 0-9

EXPLANATION
The Installer Code is used to assign the 4-digit Master Security Code. See "Master Code" in the System Operation section for procedure. If enabled, a user code is not needed to arm the system. Instead, users can press the [#] followed by an arming key to arm the system. However, the user code is always needed to disarm the system. If enabled, a report is sent if the system detects an RF jamming signal. UL installations must be 1 if wireless devices are used. All zones bypassed by this function will be displayed after the bypass is initiated. UL installations must be 0 (no forced bypass) The House ID identifies receivers and wireless keypads. If a 5827 or 5827BD Wireless Keypad or 5804BD Transmitter is being used, a House ID code must be entered, and the keypad should be set to the same House ID. You can assign RF house ID for each partition. If enabled, you can define the specific zones intended to chime when faulted while the system is in Chime mode. Use zone list 3 to assign these zones (see 81 Zone List Programming section for details).

*20 *21 *22 *23 *24 *26

*60 *61 *62

Bypass Report Code

AC Loss Report Code

*63 *64 *65 *66 *67 *68 *70 *71 *72 *73 *74 *75

Low Bat Report Code

Test Report Code

Open Report Code

Arm Away/Stay Report Code
RF Trans. Low Batt. Report Code

Cancel Report Code

Alarm Restore Report Code
Trouble Restore Report Code
Bypass Restore Report Code

AC Restore Report Code

Low Bat Restore Report Code
RF Xmtr Low Batt. Restore Code

Test Restore Report Code

Miscellaneous System Fields
FIELD TITLE and DATA ENTRIES Daylight Saving Time Start/End Month
0 = Disabled 1 = Jan 2 = Feb 3 = Mar 4 = April # + 10 = Oct # + 11 = Nov # + 12 = Dec Enter the start and end weekend for daylight savings time, if applicable to the region.
Enter the start and end month for daylight savings time, if applicable to the region.
Daylight Saving Time Start/End Weekend
0 = disabled 1 = first 2 = second 3 = third 4 = fourth 5 = last 6 = next to last 7 = third to last

Auto-Stay Arm

0 = no 1 = partition 1 only 2 = partition 2 only 3 = both partitions
With this field enabled and system armed in AWAY mode at a keypad (non-RF device), the system automatically reverts to armed STAY (or INSTANT) mode if a door is not opened and shut within the programmed exit delay time. An Opening report followed by an Armed Stay report is sent to the Central Station. Any RF device that arms the system AWAY overrides this feature and the system remains armed in the AWAY mode. Sets the maximum amount of time in which two cross zones must be tripped in an armed system to send an alarm message to the Central Station. If only one cross zone is tripped during this time, a trouble message (CID code 380) for that zone is sent to the Central Station. Assign cross zone pairs in zone list 4. This option not for use in UL installations. When enabled (1 = yes), this feature causes a CANCELED ALARM display on the LCD keypad under the following conditions: After the kissoff of the cancel message to the Central Station, indicating a successful transmission. When an alarm is successfully canceled before the Central Station received the Alarm message. E.g., if an alarm is incorrectly triggered and the user presses code + OFF before the dial delay time has expired, the message will never go out to the CS. When the Cancel report is not enabled and the system is disarmed: a. before dialer delay expires (alarm report not sent) message Canceled Alarm is displayed. b. after dialer delay expires message Canceled Alarm is not displayed. Used with zones assigned to a configurable zone type with fault delay on (configurable zone type digit 6), and sets a zone response time of 15 seconds to 15 min. It can be assigned to zones with sensors that provide a trouble indication when an oil tank is low, or similar applications for critical condition monitoring where a non-alarm response is desired. UL: May only be used on non-burglar alarm and non-fire alarm zones when used on a fire and/or UL burglar alarm installation. If an Event Logging selection is made in field 90, a message can be sent to the central station receiver when the log is 80% full. If the log becomes full, new messages overwrite the oldest messages in the log. This system has the ability to record various events in a history log (FA168C = 100 events; FA148CP = 50 events). At any time, the downloader operator can then upload the log and view or print out all or selected categories of the log. The log can also be cleared by the downloader operator. The display/printout at the central station will show the date, time, event, and description of the occurrences. Data Entry Example: To select Alarm/Alarm Restore and Open/Close, enter 9 (1+ 8); to select all events, enter #15.

Digit 8 = entry delay 1/entry delay 2 + exit delay + interior zone type

DIGIT 9

Alarm Sounds 0 = none 1 = steady keypad 2 = steady bell see fields *32, see zone type and keypad *33 09; see note = pulsing bell and keypad Digit 9 = alarm sounds + bell timeout + fire zone Use Bell Timeout 0 = no 4 = yes Respond as Fire Zone 0 = no 8 = yes

DIGIT 10

Trouble Sounds 0 = none 1 = periodic beep 2 = trouble beeps Chime when Chime Mode On 0 = no 4 = yes
Digit 10 = trouble sounds + chime
Keypad Programming Fields
NOTE: Each keypad must be assigned a unique address. Keypads programmed with the same address will give unpredictable results. FIELD TITLE and DATA ENTRIES Keypad Device Address 17
1st Digit Partition Assignment: 0 = keypad disabled 1 = partition 1 (FA168C)/enable (FA148CP) 2 = partition = common 2nd Digit Sound Option: 0 = no suppression 1 = suppress arm/disarm and E/E/ beeps 2 = suppress chime beeps only 3 = suppress arm/disarm, E/E/ beeps and chime beeps
Keypad 2 First digit: For FA168C, enter the partition in which the keypad is located; for FA148CP, enter 1 to enable, or 0 to disable. Second digit: Enter the desired sound option for this keypad. NOTE: Address 16 is reserved for keypad 1, which is automatically set to partition 1 with all sounds enabled.
*191 *192 *193 *194 *195 *196 *197

Keypad Device Address 18

See field *190 for entries.
Keypad 3 First digit: FA168C = partition (1, 2); FA148CP = enable (1)/disable (0). Second digit: Enter the desired sound option for this keypad. Keypad 4 First digit: FA168C = partition (1, 2); FA148CP = enable (1)/disable (0) Second digit: Enter the desired sound option for this keypad. Keypad 5 First digit: FA168C = partition (1, 2); FA148CP = enable (1)/disable (0) Second digit: Enter the desired sound option for this keypad. Keypad 6 First digit: FA168C = partition (1, 2); FA148CP = enable (1)/disable (0) Second digit: Enter the desired sound option for this keypad. Keypad 7 First digit: FA168C = partition (1, 2); FA148CP = enable (1)/disable (0) Second digit: Enter the desired sound option for this keypad. Keypad 8 First digit: FA168C = partition (1, 2); FA148CP = enable (1)/disable (0) Second digit: Enter the desired sound option for this keypad. If enabled, keypads display the exit time remaining after arming the system, with display updates at the interval selected (i.e. if the exit delay is 30 seconds and 2 is selected in this field, the keypad display refreshes every 2 seconds, displaying 30, 28, 26, 24, etc.). An interval greater than 1 may be necessary for some older keypads to allow users time to enter key presses between display updates. If selected, the partition number is displayed in the upper-left corner of the display. This is useful when using the GOTO partition function. Select 0 if using Alpha keypads and/or 3-digit Fixed-Word Display keypads. ECP faults will display 1 plus the device address (00-30) of device causing the fault (e.g., faults on device 07 display as 107). Select 1 if using 2-digit Fixed-Word Display keypads. If selected, ECP faults for all devices will display as 91 on 2-digit displays, and 191 on 3-digit or Alpha keypads.

Keypad Device Address 19

Keypad Device Address 20

Keypad Device Address 21

Keypad Device Address 22

Keypad Device Address 23

Exit Time Display Interval
0 = no display 1-5 = seconds between display updates

*198 *199

Display Partition Number

ECP Fail Display

0 = 3-digt display (1 + device address) 1 = 2-digit fixed-display as 91

Zone Programming

(56 and 58 Menu Modes)

About Zone Programming
Zone Programming is used to program zones, zone types, report codes, enroll 5800 RF Wireless Transmitter serial numbers, and identify the type of loop input device(s). This mode can also be used to enter alpha descriptors for programmed zones; however, we recommend entering descriptors in menu mode 82 (Alpha Descriptor Programming after all zone programming has been completed). For a faster method of zone programming, you can use the 58 Expert Programming Mode instead of 56 Zone programming. The 58 Expert Programming Mode is designed for those who have had previous experience in programming control panels of this type. NOTE: Alpha display prompts are shown in a double-line box.
Zone Programming Procedure
Zone Programming involves: 1. Entering the zone number to be programmed; 2. Making appropriate entries at the prompts; 3. Confirming the serial number of wireless transmitter zones. Start Zone Programming mode by pressing 56 while in Data Programming mode. The following prompts are displayed: PROMPT
SET TO CONFIRM? 0 = NO 1 = YES
VALID ENTRIES Set to Confirm
If 1 (Yes) is entered, you will be prompted to confirm each transmitter after entering the serial and loop numbers (at the XMIT TO CONFIRM prompt later in this procedure). We recommend that you confirm the programming of every transmitter. Enter the zone number that you wish to program. Zone 10 has been entered as an example in the display at left. Enter a report code for zone 91 to enable addressable device reporting. Enter a report code for zone 92 to enable duress reporting. 95, 96, 99 are emergency (panic) key zones. A summary display appears. IN: L appears for wireless zones and indicates input type and loop. IN: AD appears for hardwire expansion zones (AW) and indicates the modules address (AD), which is based on the zone number. HW: RT appears for hardwire zones and indicates configuration (EOL, NO, NC, zone doubling, double-balanced) and response time selection.

Zn ZT P RC HW: RT EL 1

01-64 = zone number 00 = quit [] to continue OR [D] to go to prompts for wireless key programming templates

Zn ZT P RC IN: L 10 :

Zn ZT P RC IN: L RF 1
ZT = see Zone Type chart shown in *56 Menu Mode Zone Type prompt P = partition 1, 2, 3 (common) RC = 1 (send CID report) 0 (no report) IN = input type L = loop number
A summary screen with the selected zones current programming appears. Begin programming zone information as follows: Enter Zone Type (ZT), Partition (P), Report Code (RC), and Input Device Type (IN)* sequentially, but not the Loop No. (L). Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the screen. Use the [C] key to copy the previous zones attributes. Press [] to save the programming and continue to the serial number/loop number prompt. If needed, you can press the [#] key to back up without saving. * If HW (hardwired) or AW (Auxiliary) is entered for Input Device Type, the next screen will be similar to the prompt shown, except that HW or AW will be displayed under IN. If RF, BR, or UR is entered, a prompt for Serial and Loop number will be displayed, as follows.

10 INPUT S/N: AXXX-XXX L

VALID ENTRIES Serial number
S/N = serial number L = loop number [] to continue
Manually enter the serial number (found on the transmitter label), by typing digits in the X locations, using the [A] (advance) or [B] (back) keys as required. You can also perform two open and close sequences; for button-type transmitters that means pressing and releasing the button twice. NOTE: If you want to copy the previous zones serial number, press the [C] key. Press [] to advance to the loop number, then enter loop number. Press [] to accept the existing serial and loop number and continue to the Confirm prompt below. If necessary, press [#] to back up and re-enter or edit the serial number.
To Delete a Serial Number
To delete an existing serial number, enter 0 in the loop number field. The serial number will change to all 0's as shown. If 0 was entered in error, simply re-enter the loop number, and the serial number will return to the display. The prompt to confirm appears. This prompt will only appear if the first prompt after entering 58 was answered Yes. To confirm, activate the loop input or button that corresponds to this zone. The system checks for duplicate. If a duplicate exists, a long error beep will sound. Press [#] to back up and re-enter the serial and/or loop number. If the serial/loop number combination transmitted does not match the serial and loop number entered, a display similar to the one below will appear. If the loop number does not match, it will also be displayed. If so, activate the transmitters loop input or button one or more times. If a match is still not obtained (i.e., summary display does not appear), press the [#] key twice and enter the correct loop input or, if correct, press [#] again and then enter the correct serial number. If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a summary display will appear, showing the programmed information for that zone. Press [] to begin programming the next zone. See first Summary Screen prompt paragraph on previous page.

TEMPLATE 2

TEMPLATE 5

TEMPLATE 3

TEMPLATE 6
Output Device Programming

(*79/*80 Menu Mode)

About Output Device Programming
Output Devices: The FA168C system supports up to 16 relays and/or Powerline Carrier devices (X-10 devices) plus 2 built-in trigger outputs in any combination. These 18 outputs are assigned to system-wide output numbers (01-18). Use *79 Menu Mode to assign output numbers and map them to device addresses. The FA148CP supports 8 relays and 2 built-in trigger outputs (total 10 outputs).
Output Functions: The system also provides installer-defined output functions, which can be assigned to any of the physical outputs. Therefore, the action of any one of the outputs can be based on as many of these functions as desired. This lets a single relay or X-10 device perform many functions. The controls support up to 48 output functions. Use *80 Menu Mode to define output functions. Relays and output devices are not recommended for life safety applications. NOTE: When navigating the *79 and *80 menus: The [] key is used to accept an entry and advance to the next prompt. The [#] key is used to revert back to the last question to check or change an entry. Press [] to go forward again. Output Device programming involves: 1. Use *79 Menu Mode to assign module and output numbers and map them to device addresses. NOTE: You must map output devices using *79 Menu Mode before you can use *80 menu Mode). 2. Use *80 Menu Mode to create output definitions, which control the output devices.
*79 Menu Mode: Output Device Mapping
Use this menu to assign Relay Module device addresses and specific relay numbers, and Powerline Carrier unit numbers. The system is based on predefined module addresses for 4204 and 4229 modules. Refer to the table shown at the Module Address prompt on the next page and set the modules addresses (via module DIP switches) accordingly. The following table shows how these outputs are identified. Output Identification
This output Relays: X-10 Device Built-in Outputs is identified by the Relay Modules device address and the relay position on that module (i.e. the physical relay number, 1-4, on that module). a house ID (entered in data field *27) and the unit number of the device. the output number assigned, 17 for trigger 1 and/or 18 for trigger 2.
Installation Instructions Start Output Device Mapping by pressing *79 while in Data Programming Mode. The following prompts are displayed: 79 Menu Mode PROMPT

01 Delete Zone? 0 = No 1 = Yes

Deleting a Zone

0 = dont delete zones 1 = go to next prompt to delete zones [] to continue
01 Zn to Delete? (00 = Quit) 00

Delete the Zone

01-64 = zones to be deleted from list followed by [] to accept each zone 00 to continue
Enter each zone to be deleted from the list, followed by []. After all zones to be deleted are entered, enter 00 to return to the Zone List No. prompt. so that another list can be programmed, if desired. FA168C = 01-64; FA148CP = 01-40.
Installation Instructions Notes: Any list may include any or all of the system's zone numbers. A zone list can be assigned to more than one output relay. When creating zone list 4 for cross zoning, include only zones assigned to zone types 3, 4, or 5. Do not include zones that have delays (entry/exit zones, interior w/delay) or 24-hour zones, as these zone types may produce unpredictable operation and may not function as intended.

Function Key Programming

(57 Menu Mode)
About Function Key Programming
The system provides the ability to program each of the four keypad function keys to perform one of 12 system operations. The end user can then activate the function by simply pressing and holding the programmed key for 2 seconds. Typical functions (listed below) include single-button arming, turning lights on/off, or single-button paging.
Programming Function Keys
Function key programming involves: 1. Assigning the function key number and partition; 2. Selecting the desired function for that key. Start Function Key Programming mode by pressing 57 while in Data Programming mode. The following prompts are displayed: PROMPT
Press Key to Pgm 0 = Quit 0
VALID ENTRIES Function Key
Press the desired function key, A-D. [] to continue
Press the desired function key (A-D) you want to program. NOTE: A key programmed as a function key is no longer available to be used as an end-user macro key or panic key.

BYPASS

keypad_keys-00-001-V0

INSTANT

Partition 1

Partition Number

1 = partition = partition = common partition [] to continue
Enter the partition in which the function key is active.
Key "A" Func Zone 95

Define Key Function

00-12 = see list to right [] to continue Returns to key number prompt with the next function key letter displayed.
System defaults to these function key settings. Macros 11-12 apply to FA168C only.
Enter the desired function for this key, 00 to 12, from the options listed. (00 selected for example display shown at left) 00 = For the Function key selected, the function will be as follows: If A selected = Zone 95 (emergency key, same as [1] [] pair) If B selected = Zone 99 (emergency key, same as [] [#] pair) If C selected = Zone 96 (emergency key, same as [3] [#] pair) If D selected = Single-button paging 01 = Single-button paging (sends a 999-9999 message to pager) 02 = Display time 03 = Arm AWAY (reports as User 00 if closing reports are enabled) 04 = Arm STAY (reports as User 00 if closing reports are enabled) 05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled) 06 = Step Arming (arms STAY, then NIGHT-STAY, then AWAY) 07 = Device A ctivation (for device programmed as system operation type 66function key in *80 Menu Mode) 08 = Communication Test (sends Contact ID code 601) 09 = Macro Key 1 (define macro by user code + [#] [6] [6] command) 10 = Macro Key 2 (define macro by user code + [#] [6] [6] command) 11 = Macro Key 3 (define macro by user code + [#] [6] [6] command) 12 = Macro Key 4 (define macro by user code + [#] [6] [6] command)

WARNING THE LIMITATIONS OF THIS ALARM SYSTEM (Continued)
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and remote keypad) should be tested as well. Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low-battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system. Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

INDEX

1321 AC Transformer. 1-2, 2-4, 2-11 1321X10. 1-2, 2-4, 2-11, 14-2 15-Second Dialer Delay (Burglary). 4-3
Backup Battery.. iii, 1-2, 2-5 Battery Life.. 2-9 Battery Tests.. 13-3 Bell Supervision. 1-1 Bell Supervision Jumper. 2-4 Bypassing Zones.. 12-2
Earth Ground. 2-5 ECP Fail Display.. 4-12 Enrolling. 2-9, 5-1 Entering Serial Number.. 5-5 Entry Delay.. 3-4 Entry Delay 1. 4-2 Entry Delay 2. 4-2 Entry/Exit Burglary.. EOLR.. 2-6 Event Log Full Report Code. 4-6 Event Logging.. 1-1, 4-6 Exit Delay... 4-2 Exit Error Alarm.. 12-3 Exit Error Report Code. 4-4 Exit Time Display Interval.. 4-12 Exit Warning.. 4-2 Expander Module Addresses. 2-7 Expansion Zones.. 2-7 Expert Programming Mode.. 5-4
24-Hour Audible Alarm. 3-4 24-Hour Auxiliary Alarm. 3-4 24-Hour Silent Alarm. 3-4 2-Wire Smoke Detectors. 2-6
Cabinet.. 2-1 CALIFORNIA STATE FIRE MARSHALL.. 2-5 Caller ID Unit.. 2-12 Cancel Report Code.. 4-5 Cancel Verify. 4-6 Character (ASCII) Chart.. 4 Character List.. 9-3 Charging Voltage.. 14-1 Chime By Zone.. 4-1 Chime Mode.. 12-2 Clean Me Option.. 2-6, 4-9 Common zone.. 1-1, 3-1 Communication.. 14-1 Configurable Zone Type Options. 4-10 Configurable Zone Type Programming Fields... 4-10 Confirmation Of Arming Ding. 4-2 CONTACT ID EVENT CODES. 11-3 Contact ID Reporting.. 14-1 Cross Zone Timer.. 4-6 Custom Message.. 9-3 Custom Words.. 9-3, 4

Keypad Addresses.. 2-3, 3-2 Keypad Functions. 12-2 Keypad Programming Fields.. 4-12 Keyswitch... 2-9 Kissoff.. 11-1
Local Lockout.. 4-7 Lock.. 2-1 Long Range Radio, 1-2, 2-13, 3-6, 4-2, 4-4, 3, 14-1 Low Battery Message. 13-3

Quick Arm Enable.. 4-1

Verify Operation. 2-6 VOCABULARY LIST. 9-4
Relay Module Addresses.. 2-10 Relay Modules. 2-10 Relay Programming.. 3-1 Remote Keypads.. 1-2 Report Code.. 4-4, 5-2, 5-4 Report Code Formats. 11-1 Report Format.. 4-3 Reports In Armed Period. 4-7 Response Time.. 2-7 RF House ID Code.. 4-1 RF Interference.. 2-8 RF jam detection.. 1-1 RF Jam Option.. 4-1 RF Receiver. 2-1, 2-2, 2-5, 2-8, 3-6, 3 RF System.. 4-1 Ring Detection Count.. 4-7 RJ31X Jack. 2-12
Wireless Key Templates. 5-6 Wiring Length/Gauge Chart. 2-3 Wiring Run Chart.. 2-3 Word String.. 9-3
Macros.. 1-1 Master Security Code.. 4-1 Model 112.. 2-9 Modem.. 3-1 Module Addresses.. 6-2 Momentary Switch.. 2-9
Zone Doubling.. 2-6 Zone Lists.. 3-1, 7-1 Zone Not Used.. 3-3 Zone Programming. 5-1 Zone Programming Procedure. 5-1 Zone Type Definitions.. 3-3 Zone Types. 3-3, 5-2, 6-4
No Alarm Response.. 3-4 Normally Closed Zones.. 2-6 Normally Open Zones.. 2-6
On-Board Triggers. 2-11, 2-13 Output Definition Components. 6-3 Output Device Mapping.. 6-1 Output Devices.. 3-3, 6-1 Output Functions.. 6-1 Output relays. 1-2 Output To Long Range Radio. 4-2
SA4120XM Cable.. 2-4 Schedules. 1-1, 10-1 Secondary Phone No.. 4-3 Security Codes..iv, 1-1, 12-1 SESCOA/Radionics Select.. 4-3 Silent Burglary.. 3-5 Silent Panic. 12-3 Single Alarm Sounding Per Zone.. 4-2 Smoke Detectors.. 2-6 Sniffer Mode.. 13-2 sounder connections. 2-4 Split/Dual Reporting.. 4-3 Supervised Fire.. 3-4 Supplementary Power.. 2-3 Swinger Suppression.. 4-7 System Communication.. 11-1 System Operation.. 6-4 System Status Report Codes. 4-4 System Test.. 13-1
PABX Access Code.. 4-2 Pager #1 Phone No. 4-8, 4-9 Pager Format.. 4-8 Pager Programming.. 3-2 Pager Programming Fields.. 4-8 Pager Report Options.. 4-8 Panic Keys.. 12-3 Part. 1 Primary Subs. Acct. No. 4-3 Part. 2 Primary Subs. Acct. No. 4-3 Partitions.. 1-1, 3-1 Perimeter Burglary.. 3-3 Phone Line.. 2-12 Phone Line Monitor Enable. 4-7 Phone Module 1-1, 1-2, 2-3, 2-5, 2-12, 2-13, 4-1, 4-7, 9-1, 9-3, 4 Phone Module Access Code. 4-1 Phone System Select.. 4-3 Power Failure.. 12-4 Power Supply.. 2-3 Power Up In Previous State. 4-2 Powerline Carrier Device (X-10) House ID.. 4-1 Powerline Carrier devices.. 2-4 Powerline Carrier Devicesiii, 1-2, 2-11, 12-2 Primary Phone No.. 4-3 Prompt To Confirm.. 5-5

BLK RED GRN YEL
4219 WIRED EXPANSION MODULE (8 ADD'L EOLR WIRED ZONES) -OR4229 WIRED EXPANSION/RELAY MODULE (8 ADD'L EOLR WIRED ZONES PLUS 2 OUTPUT RELAYS) -OR4204 RELAY MODULE (4 OUTPUT RELAYS) AND/OR
5881* Type RF RECEIVER WIRELESS ZONES 5881L: UP TO 8 5881M: UP TO 16 5881H: UP TO 64 *5882 IN CANADA
SET UNITS DIP SWITCH FOR DEVICE AUX PWR + 5 ADDRESSES OUTPUT _ 7 - TERMINALS SEE INSTRUCTIONS.
4-WIRE SMOKE DETECTOR CONNECTIONS
RELAY PROGRAM RELAY AS ZONE TYPE 54 (FIRE ZONE RESET) BLK
RED JUMPER CUT FOR BELL SUPERVISION. ALSO, CONNECT 2000 OHM RESISTOR DIRECTLY ACROSS SOUNDER.
TO TERM 4 TO TERM 5 TO TERM 6 TO TERM 7
SET RECEIVERS DIP SWITCH FOR DEVICE ADDRESS OF 0. SEE INSTRUCTIONS.
4-WIRE SMOKE OR COMBUSTION DETECTOR TO ZONES 2-8 TERM. (+) TO ZONES 2-8 TERM. (_) HEAT DETECTOR

VIOLET 2000 OHMS EOLR

EOL POWER SUPERVISION RELAY MODULE A77-716B
GREEN: DATA IN FROM KEYPAD

RED: KEYPAD PWR ( + )

ZONE 7

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE 6

ZONE 8

TO 110VAC UNSWITCHED OUTLET (24HR)

YELLOW: KEYPAD DATA OUT

FA168C ONLY
AUX. POWER OUTPUT 10.5-13.8VDC 600mA MAX. (500mA MAX. FOR UL INSTALLATIONS) ALL OUTPUTS ARE POWER LIMITED. NOTE: KEYPAD (S) CURRENT (IN BOTH PARTITIONS) AND ALL OTHER DEVICES DRAWING POWER FROM TERMS 4 & 5 MUST BE INCLUDED IN AUX CURRENT DRAIN CALCULATIONS.
ALARM OUTPUT 10.513.8VDC, 2A MAX. (600mA MAX. FOR UL USAGE, INCLUDING AUX POWER) STEADY FOR BURGLARY/PANIC, TEMPORAL PULSE SOUNDING FOR FIRE. CAN USE 702 SIREN, OR 12V BELL). SEE INSTRUCTIONS.
REMOTE KEYPADS AND OTHER ADDRESSABLE DEVICES (e.g. 5800TM, 4285/4286, LRR, 4219, 4229, 4204, 5881) REMOTE KEYPADS CAN USE FA260KP OR FA560KP KEYPADS. LOCAL PROGRAMMING MUST BE DONE WITH A FA560KP, BUT NEED NOT REMAIN IN THE SYSTEM (SET TO ADDRESS 16).
FOR COMPLETE INFORMATION, SEE INSTRUCTIONS K5305-5

ASSEMBLED IN MEXICO

Figure 17. Summary of Connections
BLACK: KEYPAD GROUND (- ) RETURN
CAN BE USED FOR 2-WIRE SMOKE DETECTORS
RING TIP RING TIP (BROWN) (GRAY) (GREEN) (RED)

INCOMING PHONE LINE TELEPHONE WIRING (VIA RJ31X* JACK AND DIRECT CONNECT CORD) *CA38A IN CANADA HANDSET
EARTH GROUND SEE INSTRUCTIONS FOR PROPER GROUNDING
FOR CONNECTION OF OPTIONAL 4285 OR 4286 VIP MODULES TO PHONE TERMINALS, SEE INSTRUCTIONS.

WARNING: TO

MAXIMUM LOOP RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR) RESPONSE, ZONES 1-8: 10, 350, OR 700 MSEC (PROGRAMMABLE) MAXIMUM NUMBER OF 2-WIRE SMOKE DETECTORS ON ZONE 1 IS 16; DETECTORS MUST HAVE COMPATIBILITY IDENTIFIER AS "A".

ZONE PAIRS

10 ZONE 2 11
PREVENT RISK OF SHOCK, DISCONNECT TELEPHONE LINE AT TELCO JACK BEFORE SERVICING THIS UNIT.
COMPLIES WITH FCC RULES, PART 68. FCC REGISTRATION NO. 5GBUSA-44003-AL-E RINGER EQUIVALENCE: 0.1B. THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

DOC LOAD NO.: 3

2k 3k ZONE 10

2 / / / / / / / 16

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.
TYPICAL WIRING FOR DOUBLE BALANCED ZONE (FA168C ONLY)
TYPICAL WIRING FOR ZONE DOUBLING (FA168C ONLY)
ALL DEVICES AND ACCESSORIES USED IN A CANADIAN INSTALLATION MUST BE LISTED FOR USE IN CANADA

FA168C148CP-SOC-V0

LIMITED WARRANTY
Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its First Alert products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 36 months from the date stamp control on the product or, for products not having a date stamp, for 30 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than First Alert Professional factory service. For warranty service, return product transportation prepaid, to: First Alert Professional Factory Service, 165 Eileen Way, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized