INSTRUCTIONS FOR SMPTE AND MIDI SONG POSITION POINTER
TO GENERATE SMPTE (STRIPING): 1. 2. Press Sync input options button and select 4 (prnt). Select the desired frame format (24F, 25F, 30F or 30D) by using the up and down arrows.
3. Using the right and left arrow and the 10-Key pad, enter the start time in Hours: Minutes: Seconds: Frames (for example: 00:00:15:00 would start the stripe at 15 seconds SMPTE time and continue until you press stop). The start time you choose is pretty much up to you unless youre working in film and video, where the start and end times will have an important relationship to a video cassette or film. 4. Make sure the SMPTE OUT (SYNC OUT on the 9000) is connected to the input of your tape recorder. 5. After putting your tape machine in record on the appropriate channel, press enter to start printing SMPTE code to tape. The Forat SMPTE card will respond to levels as low as -15dB but its best to record SMPTE as hot as you can get away with. 6. To stop SMPTE generation, press stop after the desired time has elapsed. Remember to leave at least 10 seconds extra at the end. The 9000 will stop, if loop to bar is set to stop at end or it will loop to the entered bar when it reaches the end of sequence. Example: You have a song which is 3 minutes long. No offset is usually necessary when generating code for audio interlock with the 9000, so you can just leave all values at 00:00:00:00 and, once your tape machine is in record, simply press enter to start generating SMPTE code. Allowing for an extra 15 seconds of pre-roll and 10 seconds of post roll, you would want to generate code for a total time of about 3 minutes 25 seconds, or until the readout reads 00:03:25:00. TO READ SMPTE: 1. Press sync input options button, and select 3 SMPTE.
2. If necessary, change the frame format to match the SMPTE printed on tape by using the up and down arrows. 3. Enter an appropriate offset time using the right arrow and the number key pad. The time you enter here is the SMPTE time at which you want the sequence to start playing and it should allow for at least 15 seconds pre-roll.For example, if the SMPTE on tape starts at 00:00:00:00 you should enter an offset of 00:00:15:00. This allows time for the 9000 and the various tape machines to become locked together, and to run in synchronization.
Note: If no offset is entered, the 9000 may not play the first 8th note of the sequence. 4. Make sure the output of the tape recorders SMPTE track is connected to the SMPTE IN jack on the 9000. 5. Once the offset has been entered, --:--:--:-- is displayed, indicating that the 9000 is waiting for SMPTE. NOTE: While the 9000 is waiting for SMPTE to start, it will not respond to any pads or buttons but stop, record and cancel current operation until the SMPTE has started the sequence. You may enter in and out of record mode while the 9000 is waiting for SMPTE to start, by pressing the record button. 6. Start the tape machine rolling; the 9000 will display the incoming SMPTE code and starts the sequence at the offset entered at step 3. Important: Tempo and offset are unrelated to SMPTE. To insure accurate SMPTE lock up to tape, the exact tempo and offset values for each song must be entered each time SMPTE is used. Make a record of these values for every song to avoid headaches! As of 7.09 software, you may save all user set variables such as Smpte start time and tempo, etc to disk as part of a Save All file. MIDI SONG POSITION POINTER AND MIDI CLOCK To read MIDI Song Pointer and MIDI clock press the Sync input options button and select 2 MIDI. While in this mode the 9000 responds to MIDI commands such as start, stop, continue and Song Pointer received on the MIDI input jack. You may enter record mode by pressing the record button while the 9000 is waiting for MIDI clock to start. The 9000 will not send MIDI Song Pointer or MIDI clock out of its MIDI out jack while reading MIDI clock if this is desired, use the MIDI through on the 9000. MIDI clock is only sent while in play, record, SMPTE read or sync to tape modes.
If you have any questions please call Bruce Forat at (818)763-3007.

Application Format for Claiming Reimbursement of Certification Charges of acquiring ISO-9000/ISO-14001 Certificate under the Incentive Scheme of O/o Development Commissioner (SSI), M/o Small Scale Industries, Nirman Bhawan, New Delhi-110011. 1. (a) Name and address of the unit [Office & Factory Location (s).] (b) Telephone No. Factory & Office (c) E-mail & Fax 2. Details of PMT SSI Registration No.; date of issue; Directorate of Industries/ GM, DIC of the State concerned (Enclose an attested copy of all pages of SSI Registration Certificate) Item (s) of manufacture/processing as indicated in the PMT SSI Registration. Proof of SSI status and functional status of the unit as on the date of submission of Application The following document(s) to be submitted
A certificate (in original) from State DI/GM,DIC confirming SSI and functional status of the unit at the time of acquiring ISO-9000/ ISO-14001 certificate; as on date as per Format at Annexure I. OR
An Affidavit (in original) from Managing Director/ Director/Proprietor/Partner of the SSI unit duly sworn before a Notary Public confirming SSI status and functional status of the unit at the time of acquiring ISO-9000/ISO-14001 certificate; and as on date,( As per Format Annexure II) accompanied by CA certificate of the total investment in plant & machinery as on date (original purchase value) (As per Format Annexure III)
Details of ISO-9000/ISO-14001 Certificate Name and address of Certification agency; The Certificate must have address of the site/location certified; Scope of certification, Certificate No , date of issue & period of validity (or date of expiry), Name & Logo & Number of the Accreditation Body/Board. (Enclose an attested copy of the Certificate) Details of expenditure incurred in acquiring ISO-9000/ ISO-14001 Certificate (excluding hotel & travel expenses & surveillance charges). Furnish a CA certificate of expenditure (in original) giving the details (as per the Format Annexure IV). Details of reimbursement/grant/subsidy already received, if any, from Centre Govt (including DC(SSI) / State Govt./Financial Institution etc. for acquiring ISO-9000/ ISO-14001Certificate ( Furnish, an Undertaking/declaration (in original) from the Managing Director/Director/ Proprietor/ Partner of the SSI/ ancillary units duly sworn before Notary Public as per the Format Annexure V) Pre-receipt to be furnished as per Format at Annexure VI.
Declaration: I (full name).,,S/o of. Managing Director/Director/Proprietor/Partner of M/s. (complete address) hereby declare that the particulars given in the application are correct. In case any of the statement/information furnished in the application/documents later found to be wrong or incorrect or misleading, I do hereby bind myself and my unit to pay to the Government on demand the full amount received as reimbursement in respect of above mentioned activity, within seven days of the demand being made to me in writing.
Name and Signature of Managing Director/ Director/Proprietor/Partner of SSI unit. (Full Name) Note: (a) The copy of SSI Registration, ISO-Certification must be attested by any one of the followings:
(1)GM (DIC) or (2) Director, SISI of the Region or (3) Chartered Accountant (with name of the signatory, CA Stamp, and CA Membership No. )