Chronograph Stopwatch VD54 (with date - VD53)

(1 crown/2 pushers)

A MINUTE HAND

24-HOUR HAND

SECOND HAND
Time and Date Setting 1. Before setting the time, make sure the chronograph is stopped and set to zero (12:00) position. 2. Pull crown out to position 2. 3. Turn crown clockwise until the previous days date is displayed. 4. Pull crown out to position 3 when the second hand is at the 12:00 position. 5. Turn crown to set time. Note: 24-hour hand moves correspondingly with the hour and minute hands. When setting the time be sure to check that the 24-hour hand is set properly. 6. Return crown to position 1. Note: When the crown is in position 2, do not press the pushers. Otherwise the chronograph hands will move. Chronograph 1. Press A to start/stop the chronograph. 2. Press B to reset to zero. Split Time 1. Press B while the chronograph is running. 2. Press B again to return to the chronograph. 3. Press A to finalize timing. 4. Press B to reset. Chronograph Zero Reset 1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 3. 2. Press A to move hands clockwise; press B to move hands counter-clockwise. 3. Return crown to position 1.

1. Pull the crown out to position 2. 2. Turn the crown counter-clockwise to set the date. 3. Push the crown back to the position 1.
Date Watch GL10, IS13, VJ32A11, VJ32A31, 9T13, 505.2-3, 515.1-3, 515.2-3, 585.2, 715-2, 2115, 2315

Date Setting

1. Pull the crown out to position 2. 2. Turn counter-clockwise and set the date for the previous day.

(1) (2) DATE

Time Setting
1. Pull crown out to setting 3. 2. Turn counter-clockwise to advance the time and continue until the day/date changes to the present day. 3. Set the correct time. 4. Push crown back to position 1.
Day/Date Watch IS02, 507.2-3, 517.2, 2105, 2305, 2405
1. Pull the crown out to position 2. 2. Turn clockwise and set the date for the previous day.

Day Setting

With crown still in position 2, turn counter-clockwise and set the day for the previous day.
3 Hand with EL Watch 6N30/OU30

EL FUNCTION

The EL (light-up) button is located above the crown. Pressing it once will activate the light-up function of the display making the display face visible in low-light situations for 3 seconds.
DZ1065 and DZ1066 hold rights covered under U.S. Patent numbers: 6,106,127, 6,299,321, and 6,486,561.

EL BUTTON

Dual Time Watch K62/132
1. Push buttons to move hands. 2. Set correct time.

buttonS

Sub-Second 1L45
Pull crown out to position 2 and rotate to set time.
NOTE: When crown is pushed back to position 1, small second hand begins to run.
SMALL SECOND HAND (1) (2)
2 Eye Day/Date Multifunction VX36A1

(1 crown)

DATE DAY (1) (2) (3)

DATE SETTING

1. Pull crown out to position 2. 2. Turn clockwise to advance date hand. 3. Push crown back to position 1.

DATE AND TIME SETTING

1. Pull crown out to position 3. 2. Turn clockwise to advance hour and minute hands.
The hand showing days of the week will also move with the hour and minute hands. Keep turning until you have reached the desired day.
Two Eye Multifunction 6P25, 6P75
1. Pull crown out to position 2. 2. Turn counter-clockwise to select date.

DATE DATE

(1)(2) (3)

Day and Time Setting

1. To set time, pull crown out to position 3. 2. Turn clockwise to set hour and minute hands. The hand showing days of the week will also move with the hour and minute hands. Keep turning until you have reached the desired day. 3. Push crown back to position 1.

Multifunction 6P27

NOTE: Chronograph minute hand will synchronize with chronograph second hand during chronograph zero reset.

Chronograph OS60

MINUTE HAND HOUR HAND
1. Pull the crown out to position 3. Chronograph second hand and 1/20 second hand will return to zero position. Do not return the crown to its normal position while the hands are returning to zero, or else the position the hands are at when this is done will be recognized as the new zero position. 2. Turn the crown to set the desired time. 3. Return the crown to its normal position.
(1) (2) (3) 1/20 SECOND HAND
1. Pull the crown out to position 2. 2. Turn the crown counter clockwise until the correct date is shown in the date window. 3. Return the crown to its normal position.
1. Pull the crown out to position 3. Chronograph second hand and 1/20 second hand will return to zero. Do not return the crown to its normal position while the hands are returning to zero. Doing so will cause the position of the hands to be recognized as the new zero position. 2. Push (A) to set the chronograph second hand to 12:00 (zero) position. Each press of (A) advances the chronograph second hand one mark. If (A) is held down for over 2 seconds, the chronograph second hand advances continuously. 3. Push B to set the chronograph 1/20 second hand to 12:00 (zero) position. Each press of (B) advances the 1/20 second hand one mark. If (B) is held down for over 2 seconds, the 1/20 second hand advances continuously. 4. Return crown to its normal position. 5. Press (B) to reset all hands to the zero position.
1. Push (A) to start/stop the chronograph. 2. Push (B) to reset the chronograph. 3. When the measured time is over 30 seconds, the 1/20-second hand stops; however, the watch continues measuring the elapsed time. The exact time elapsed is indicated when A is pressed to stop the chronograph, and the 1/20-second hand moves to the actual time. The hand returns to the 0 position when B is pressed and the chronograph is reset. 4. If (B) is pressed again after chronograph is reset, the 1/20-second hand changes to measure each second.
Chronograph Stopwatch VD55B, VD57B
(1 crown/2 pushers) Time Setting
1/10 SECOND HAND MINUTE HAND (1) (2) (3) SECOND HAND
1. Pull crown out to position 3. 2. Set time by turning the crown clockwise. 3. Push back to position 1 to start the watch.

Using the Stopwatch

1. Press A to start/stop the stopwatch. 2. Press B to control the split time and reset.
Stopwatch Hand Adjustment

1. Pull crown out to position 3. 2. Press A to reset the stopwatch 1/10 second hand to the 0 position. 3. Press B to reset the second and minute hands. The hands only move clockwise. 4. With each press of A or B, the hands move one position. They move quickly if the buttons are kept pressed.
Note: If the stopwatch hands function improperly, pull out crown and press A and B at the same time for over 2 seconds. When the buttons are released, the stopwatch second and 1/10 second hands will spin around and return to 0. This will indicate that the internal circuit has been reset.
Date Setting (on some models only)
1. Pull crown out to position 2. 2. Turn clockwise until desired date appears in window. 3. Push crown back to position 1.

Chronograph ISA 8161/202

(1 crown/2 pushers) Setting the time

MINUTE HAND SECOND HAND

1. Pull crown out to position 3. 2. Set time by turning the crown. 3. Push the crown back to position 1.

(B) DATE

Setting the Date
1. Pull crown out to position 2. 2. Set date by turning the crown. 3. Push the crown back to position 1.
Resetting Chronograph (after battery exchange or mishandling only)
1. Press both A and B pushers at the same time. 2. Next press B to reset the minutes. 3. Then press A to reset seconds. 4. To exit press both A and B pushers at the same time.
Measuring Cumulative Times
1. Press A pusher to start. 2. Press A pusher to stop. 3. Press B pusher to reset.

Measuring Split Times

1. Press A pusher to start. 2. Press B pusher to split. 3. Press B pusher to restart. 4. Press A pusher to stop. 5. Press B pusher to reset.

Chronograph ISA 8171/201

Time and date setting
1. Pull crown out to position 2. 2. Rotate crown clockwise until the previous days date is shown in the date window. 3. Pull crown out to position 3. 4. Rotate crown clockwise until the correct date is shown in the date window. 5. Continue to rotate crown to set correct am/pm time. 6. Return crown to position 1.
Note: Do not set the date between 9:00 p.m. and 12:30 a.m. to ensure accuracy.
Chronograph 1/5 second hand Chronograph minute hand Date (A) SECOND HAND

(1) (2) (3) (B)

Chronograph operation
1. Press A to start/stop the chronograph. 2. Press B to restart/reset.
Note: After 2 hours of continuous running, the chronograph will automatically stop and reset to save the battery.

Split time

1. Press B while the chronograph is running. 2. Press B again to return to the chronograph. 3. Press A to finalize timing. 4. Press B to reset.

Chronograph zero reset

1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 2. 2. Press B to reset chronograph minute hand. Each press of B will advance the chronograph minute hand by one increment or press and hold B for fast advance. 3. Press A to reset chronograph 1/5 second hand. Each press of B will advance the chronograph 1/5 second hand by one increment or press and hold B for fast advance.

SIMPLE ANALOG (1 crown)

1. Press and hold B for 2 seconds to enter setting mode; year will begin flashing. 2. Press A to advance digit; press and hold A for fast advance. 3. Press B to set and advance to next setting value. 4. Setting sequence is year, month, date, hour, minute. 5. Press B to exit setting mode.
Note: Hour will be displayed in 24-hour format in time setting mode. Note: If no pusher/button is operated for 30 seconds, all changes will be saved and the setting will automatically return to display mode.

Digital FL137AX

(A) (B)

DIGITAL FL137AX

(2 pushers)

Digital FL137EA

Ana-Digi FL052I
1. Press A to change mode. Mode sequence is: normal time, world time, alarm, chronograph, memory recall, timer. 2. Press B for EL. 3. Press C to toggle chime on/off. 4. Press D to toggle DST on/off for the selected city. 5. In any mode or setting, if no pusher is operated for 60 seconds, setting will be returned to normal time display.

(B) (C)

TIME AND CALENDAR SETTING
1. Press and hold B for 2 seconds to enter setting mode. 12/24-hour time will begin flashing. 2. Press C to select 12/24-hour time. 3. Press A to set and advance to seconds. 4. Press C to reset seconds to zero. 5. Press A to set and advance to minute. 6. Press C to increase the digit; press D to decrease the digit. 7. Press A to set and advance to next setting value. 8. Setting sequence is: 12/24-hour format, seconds, minute, hour, year, month, date, and city. 9. Press B to exit setting mode.
Note: Weekday will automatically update upon exiting setting mode.

ALARM SETTING

1. Press and hold B for 2 seconds to enter setting mode; minutes will begin flashing. 2. Press C to increase the digit; press D to decrease the digit. 3. Press A to set and advance to hour. 4. Press C to increase the digit; press D to decrease the digit. 5. Press B to exit setting mode.
Note: Alarm is automatically turned on when setting is changed.

WORLD TIME MODE

1. Press A to change to world time mode. 2. Press C to select city. 3. Press D for DST on/off for the selected city.
Words MDY HNL ANC LAX DEN CHI NYC CCS RIO -2H -1H LON City Midway Honolulu Anchorage Los Angeles Denver Chicago New York Caracas Rio de Janeiro -2H -1H London Hour Difference -11 hours -10 hours -9 hours -8 hours -7 hours -6 hours -5 hours -4 hours -3 hours -2 hours -1 hour 0 hours Words PAR CAI MOW DXB KHI DAC BKK HKG TYO SYD NOU AKL City Paris Cairo Moscow Dubai Karachi Dacca Bangkok Hong Kong Tokyo Sydney Noumea Auchland Hour Difference +1 hour +2 hours +3 hours +4 hours +5 hours +6 hours +7 hours +8 hours +9 hours +10 hours +11 hours +12 hours

CHRONOGRAPH MODE

1. Press A to change to chronograph mode. 2. Press C to start the chronograph; press D to stop the chronograph. 3. Press D again to reset.

SPLIT TIME

PRESS ONCE TIME OF DAY PRESS AND HOLD PRESS ONCE CHRONO PRESS AND HOLD PRESS ONCE TIMER PRESS AND HOLD PRESS ONCE ALARM PRESS AND HOLD PRESS ONCE SETTING PRESS AND HOLD A LIGHT EL EL EL EL EL B MODE CHRONO SETTING TIMER ALARM SETTING TIME OF DAY SETTING NEXT FIELD CONFIRM/EXIT C START/SPLIT TOGGLE TIME/DATE TIME FORMAT START/SPLIT START INCREMENT FAST INCREMENT D RESET/STOP CHIME ON/OFF STOP RESET STOP RESET ALARM ON/OFF DECREMENT FAST DECREMENT
NOTE: - Analog time and digital time may not be in sync. - The key tone enable/disable will be dependent on the HOURLY CHIME enable/disable status.

Digital FO-001

NORMAL TIME DISPLAY Press A to change display. Display sequence is normal time, date, seconds. TIME AND CALENDAR SETTING 1. In normal time display, press B twice; month will begin flashing. 2. Press A to increase digits. 3. Press B to advance to next setting value. 4. Setting sequence is: month, date, hour, and minute. 5. Press B to exit setting mode.
NOTE: At any point in setting mode, press A to exit setting mode and return to normal time display.

- 10 -

Digital FDT003 / BD3000
Alarm Version FDT003 / BD3000
This instruction book is set-up to mirror the logic of the digital module. The features DUAL TIME, ALARM, CHRONOGRAPH and TIMER are described in the order they appear as in the module. Therefore almost all setting instructions fall under the OPTIONS section. Each mode of operation is covered in detail below; however, there are a number of unique innovations that need to be explained first.

B D C A E

Mode Icon Legend
TIME 1,2 OPTIONS AUTO EL ALARM Week,1,2 ALARM mode icon/on Hourly chime on CHRONO COUNTDOWN TIMER
The EL (light-up) button is (C). Pressing it once will activate the light-up function of the display making the display face visible in low-light situations for 3 seconds. Press and hold the EL button for 2 seconds and the AUTO EL function is turned on, marked by the Auto EL icon. This function enables the EL to be activated with the pressing of any function buttons. To turn this function off, press and hold the EL button again for 2 seconds.

Figure 1

Figure 2

Figure 3

~ continued on next page ~

- 11 -

CHIME When Chime is on, your watch will chime once on the hour every hour: A chime will also accompany mode changes, with a higher pitched chime signaling the TIME mode. 1. To set Chime on or off, press (B) till Options is activated. Press either (D) or (E) till Alrms is highlighted, press (A) to select. 2. Press either (D) or (E) till Chime is highlighted, press (A) to select. The Chime icon will activate indicating that the chime is on. (see Fig. 1) 3. Press (A) again to turn chime off.
SETTING ALARMS 1. Press (B) till Options icon is activated. Press either (D) or (E) till Alrms is highlighted, press (A) to select (see Fig. 2). The Alarm W, 1, 2 icons will begin to flash. 2. Press either (D) or (E) to highlight, Alarm Weekday, 1 or 2, AL-wk, AL-1 or AL-2 and press (A) to select. Either the Alarm W, 1, or 2 icon will begin to flash depending on your selection. ALARM- WEEK, AL-wk 1. Pressing (D) will + the minute while pressing (E) will the minute. Press (A) to select and advance to the HOUR setting. 2. Pressing (D) will + the hour while pressing (E) will the hour. Press (A) to select. At this point blinking minutes will appear again on the display and you may go through and change any of the settings again or press (B) to EXIT and return to the AL-wk, AL-1, AL-2 or Chime menu. Pressing (B) again will take you back to the Options menu.

Alarm Weekday display

ALARM 1, 2, AL-1, AL-2 1. Press either (D) or (E) to highlight Alarm 1 or 2, AL-1 or AL-2 and press (A) to select. Either the Alarm 1, 2 icon will begin to flash depending on your selection. 2. The Alarm 1 or 2 default view will display with the MINUTES flashing. Pressing (D) will + the minute while pressing (E) will the minute. Press (A) to select and advance to the HOUR setting. 3. Pressing (D) will + the hour while pressing (E) will the hour. Press (A) to select and advance to the MONTH setting. 4. Pressing (D) will + the month while pressing (E) will the month. Press (A) to select and advance to the DATE setting. 5. Pressing (D) will + date while pressing (E) will the date. Press (A) to select. At this point blinking minutes will appear again on the display and you may go through and change any of the settings again or press (B) to EXIT and return to the AL-wk, AL-1, AL-2 or Chime menu. Pressing (B) again will take you back to the Options menu.

Figure 2 Figure 2

Figure 1 Figure 1

- 12 -

Digital FL075AB

DISPLAY MODES

The digital portion of the module has (3) three display views which are selected by pressing (A). 1. While in TIME view, whether in 12 or 24 hour display is irrelevant, press (A) once and the DATE view will appear. 2. To have alternating views between TIME and DATE press (A) a second time and each view will display for 1 second. 3. To return to TIME only view press (A) for a third time.

SECOND

SETTING TIME/DATE

MINUTE

1. Press (C) to enter SET mode. The YEAR will begin flashing, press (A) to change the year. This module features an auto calendar from 2000 to 2050. 2. Press (C) to advance to the MONTH setting. The month will begin flashing, press (A) to change the month. 3. Press (C) to advance to the DATE setting. The day will begin flashing, press (A) to change the date. 4. Press (C) to advance to the 12hr/24hr setting. The 12h characters will begin flashing, press (A) to change to 24h. 5. Press (C) to advance to the HOUR setting. The hour will begin flashing, press (A) to change the hour. 6. Press (C) to advance to the MINUTE setting. The minute will begin flashing, press (A) to change the minute. 7. Press (C) to advance to the SECONDS reset. The seconds will begin flashing, press (A) to reset to 00. 8. Press (C) to exit SET mode.

TIME DISPLAY MODE

SHOWING DATE

Digital MLG367D, FL610AB

1. Press A to change mode. Mode sequence is normal time, alarm, time zone 2, timer, and chronograph. 2. Press B for EL.
Note: At any point in any setting mode, press D to exit setting mode. Note: In any setting mode, if no pusher is operated for 2 minutes, all changes will be saved and the setting will automatically return to display mode.

(B) LIGHT (C) START/STOP

1. In normal time display, press D; seconds will begin flashing. 2. Press C to set seconds to zero. 3. Press A to advance to hour. 4. Press C to advance digit, press and hold C for fast advance. 5. Press A to set and advance to next setting value. 6. Setting sequence is: seconds, hour, minute, year, month, and date. 7. Press D to exit setting mode.

Note: In any mode, press and hold C 3 seconds to change to chronograph mode. Note: At any point in any setting mode, press B to exit setting mode. Note: In any setting mode, if no pusher is operated for 30 seconds, all changes will be saved and the setting will automatically return to display mode.
Time and Calendar Setting
1. In normal time display, press and hold B 3 seconds; hour will begin flashing. 2. Press C to increase digit; press D to decrease digit. Press and hold C or D for fast increment/decrement. 3. Press A to set and advance to next setting value. 4. Repeat steps 2 and 3 through setting sequence. Setting sequence is: hour, minute, second, year, month, date, 12/24-hour format, month/date or date/month format. 5. Press B to exit setting mode. 6. To set Time Zone 2, press and hold D 3 seconds to change to Time Zone 2. Then use steps 1-5 to set.
Note: Weekday is automatically updated upon exiting setting mode.

Countdown Timer

1. Press A to change to timer mode. Default setting is 5 minutes. 2. Press C to start timer; press D to stop the timer. 3. Press and hold D 3 seconds to clear the countdown and reset the timer.
Note: Alarm will sound for 20 seconds when countdown reaches zero. Press any pusher to silence alarm.

Recall Mode

Timer Setting
1. Press A to change to recall mode.
Note: If no data is stored, display will show NO DATA. If data is saved, display will show the current set (1-9).
2. Press C to toggle through set data: total time, best time, average time, and each lap (up to 100 laps). 3. Press D to display current set; press D again to scroll to next set. 4. Press and hold D 3 seconds to delete all stored data in the current set.
Note: At any point in recall displays, press A to exit and change to alarm mode.
1. In timer mode, press and hold B 3 seconds to enter setting mode; hour will begin flashing. 2. Press C to increase digit; press D to decrease digit. Press and hold C or D for fast increment/decrement. 3. Press A to set and advance to next setting value. 4. Repeat steps 2 and 3 through setting sequence. Setting sequence is: hour, minute, seconds. 5. Press B to exit setting mode.
1. Press A to change to alarm mode. 2. Press C to toggle alarm on/off. 3. Press D to toggle alarm 1/alarm 2.
1. In any mode, press and hold C 3 seconds to change to chronograph mode. 2. Press C to start the chronograph; press D to stop the chronograph. 3. Press and hold D 3 seconds to reset to zero.

Lap Counting

1. Press C while the chronograph is running for lap reading.
Note: If no other pusher is pressed after C is pressed, display will automatically show total chronograph time after 5 seconds, then next lap running time after another 5 seconds.

- Press (C) to select the alarm. - Press (D) to enable/disable the alarm. - Press (B) to change to Time mode again. Alarm Setting Mode - Press and hold (A) for 2 seconds to enter the alarm settings mode. - Press (C) and (D) to increase or decrease the settings value. - Press (A) to exit the settings mode. - 15 -

Digital FO-002

1. Press B for EL. 2. Press C to display date. 3. Press D to display alarm. will be displayed for alarm on. 4. Press C and D to toggle alarm on/off. 5. Press A and D to toggle chime on/off. All weekdays will be displayed for chime on.

TIME/DATE SETTING

1. From normal time display, press A 3 times to enter setting mode; seconds will begin flashing. 2. Press C to reset seconds to zero. 3. Press D to advance to minutes. 4. Press C to advance setting value. 5. Press D to set and advance to next setting. 6. Setting sequence is: seconds, minutes, hour, day, month, and weekday.
NOTE: When setting the hour, H is displayed for 24 hour format; A or P for 12 hour format.
1. From normal time display, press A 2 times to enter setting mode; hour will begin flashing. 2. Press C to adjust setting value. 3. Press D to set and advance to minutes. 4. Press C to adjust setting value. 5. Press A to exit setting mode and return to Normal Time Display.
NOTE: Alarm will sound for one minute. Press D to stop alarm sound; press C for 5 minute snooze.
1. From normal time display, press A 1 time to enter chronograph mode. 2. Press C to start/stop the chronograph. 3. Press D to reset to zero.
NOTE: While the chronograph is running, press A to return to Normal Time Display. Chronograph will continue running in the background.
1. Press D while the chronograph is running. 2. Press C to finalize timing and exit split count. 3. Press D to display all counts. 4. Press D to reset.

Digital ZD0603B01

1. In normal time display, the display is off. 2. When the display is off, press A or B to enter time/date mode. A real time display scrolling animation will appear on the display first, and then the time display will be shown for 1 second. Followed by date display scrolling animation, the date display will also be shown for 1 second, and then it will automatically shut off.

1. Press and hold A to enter setting mode; 12/24 hour format selection will begin flashing. 2. Press A to select 12/24 hour format. 3. Press B to set and advance to hour. 4. Press A to advance the setting value. 5. Press B to set and advance to next setting. 6. Setting sequence is: 12/24 hour, hour, minute, date, month, year. 7. Setting will automatically return to time display after year is set.
NOTE: The weekday will automatically be updated when the date, month, and year are set.

Digital MLL033

1. Press A to display month and date for 3 seconds. 2. Press A twice to display seconds; press A again to return to normal time display.
1. Press B twice, to display month. 2. Press A to advance digit. Press and hold A for fast advance. 3. Press B to set and advance to next setting value. 4. Setting sequence is month, date, hour, minute. 5. Press B to set. 6. Press A to activate watch. Watch is activated when colon is flashing.
Note: To change from 12 to 24-hour format, when setting hour, scroll through all digits. 12-hour format is indicated with A and P, and 24-hour format is indicated with H.

- 16 -

LED Digital MLG-035
1. Press A to display time for 8 seconds. 2. Press A again (while display is on) to change mode. Mode sequence is time, date.
Note: Animation will be displayed before time or date for 2 seconds. Note: If no pusher is operated for 8 seconds, settings will be saved and the display will return to normal time display.
1. Press A to display time. 2. Press and hold B, 12/24 hour format will begin flashing. 3. Press A to select 12/24 hour format.
Note: In 12-hour format, a small dot will be shown in the upper left hand corner of the display to indicate p.m. time.
4. Press B to set and advance to hour. 5. Press A to advance digit; press and hold A for fast advance. 6. Press B to set and advance to next setting value. 7. Setting sequence is: 12/24 hour format, hour, minutes. 8. Press B to save and exit setting mode.
1. Press A to select date mode. 2. Press and hold B, date will begin flashing. 3. Press A to advance digit; press and hold A for fast advance. 4. Press B to set and advance to month. 5. Press A to advance digit; press and hold A for fast advance. 6. Press B to save and exit setting mode.
Curved LED Digital MLL-045
NORMAL TIME DISPLAY 1. Press B for time display and animation. 2. Press B again to toggle time/date mode. 3. When time or date is displayed, press and hold B for 3 seconds to toggle horizontal/vertical display. TIME AND DATE SETTING 1. From time display, press and hold A; 12/24 hour format will begin flashing. 2. Press B to select 12/24 hour format.
NOTE: In 12 hour format, a small dot will be shown in the upper left hand corner of the display to indicate p.m. time.
3. Press A to set and advance to hour. 4. Press B to advance digit. 5. Press A to set and advance to next setting value. 6. Setting sequence is: 12/24 hour format, hour, minutes, date, month. 7. Press A to save and exit setting mode.

NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will return to normal time display.
PERSONAL MESSAGE SETTING 1. Press B to display time, press B again to display date, press and hold A; first letter of message will begin flashing. 2. Press B to select character. 3. Press A to set and advance to the next character. 4. Repeat steps until desired message. Please note there are only ten spaces available.

OLED MODULE

The display is normally off. To activate display, press A for date display with scrolling time (Figure 1), or press B for time/date display with animation (Figure 2).
NOTE: Animation is randomly selected from 4 designs. Press B to change animation.
1. When the display is activated, press and hold A for 2 seconds to enter setting mode. Hour will begin flashing. 2. Press B to advance digit. Press and hold B for fast advance. 3. Press A to set and advance to next setting value. 4. Setting sequence is hour, minute, month, date, year, 12/24 hour format. 5. After the minute has been set, the seconds will reset to zero. 6. After 12/24 hour format has been selected, settings will be saved and the display will automatically return to time display.
NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will return to time display.

- 17 -

Digital BJ2718, BJ2679, BJ2957
NORMAL TIME DISPLAY 1. Press A to change mode. Mode sequence is normal time, chronograph, alarm, and time setting. 2. Press B for EL. 3. Press C to display date. 4. Press D to display alarm. 5. Press A+D to toggle chime on/off. (all days of week will display for on.) 6. Press C+D to toggle alarm on/off. CHRONOGRAPH MODE 1. Press A to change to chronograph mode. 2. Press C to start/stop the chronograph. 3. Press D to reset to zero.
NOTE: Press A while the chronograph is running to return to normal time display; chronograph will continue running.
SPLIT TIME 1. Press D while the chronograph is running for split time. 2. Press D again to measure multiple split times. 3. Press C to finalize timing. 4. Press D to scroll through all counts. 5. Press D again to reset to zero. ALARM SETTING 1. Press A to change to alarm setting mode; hour will begin flashing. 2. Press C to increase digit; press and hold C for fast advance. 3. Press D to confirm. 4. Press D again to toggle to minutes. 5. Press C to increase digit; press and hold C for fast advance. 6. Press A to save data and return to normal time display.

NOTE: Alarm will sound at preset time for 60 seconds. Press D to silence alarm, or press C for 5 minute snooze.
TIME AND CALENDAR SETTING 1. Press A to change to time and calendar setting; seconds will begin flashing. 2. Press C to set seconds to zero. 3. Press D to advance to minutes. 4. Press C to advance digit; press and hold C for fast advance. 5. Press D to advance to next setting value. 6. Setting sequence is: seconds, minutes, hour, date, month, weekday. 7. Press D to exit setting mode.
NOTE: When setting the hour, H will be displayed for 24-hour format; A or P for 12-hour format.

Digital BJ3101

NORMAL TIME DISPLAY 1. Press A for EL. 2. Press A to display date. TIME AND DATE SETTING 1. Press B to enter setting mode; seconds will begin flashing. 2. Press A to set seconds to zero and return to normal time display. 3. Press B twice to set hour. 4. Press A to increase digit; press and hold A for fast advance. 5. Setting sequence is hour, minutes, month and date. 6. Press B to exit setting mode.

CURVED LED QFL631

NORMAL TIME DISPLAY 1. Press B for time display. 2. Press B again immediately for date display. 3. After time or date display, message will scroll. Display will automatically turn off after message scrolling is complete. TIME AND DATE SETTING 1. Press and hold A for 2 seconds to enter setting mode; 12/24-hour format will begin flashing. 2. Press B to select 12/24 hour format. 3. Press A to advance to hour. 4. Press B to increase digits; press and hold B for fast advance. 5. Press A to advance to next setting value. 6. Setting sequence is: 12/24-hour format, hour, minutes, year, month, date 7. Press A to save and exit setting mode.
NOTE: If no pusher is operated for 7 seconds, settings will be saved and the display will automatically turn off.
MESSAGE SETTING 1. In calendar mode, press and hold A for 2 seconds to enter setting mode; first character will begin flashing. 2. Press B to change the character. 3. Press A to advance to next character.