Installation Manual MULTI DISPLAY RD-30
SAFETY INSTRUCTIONS... i SYSTEM CONFIGURATION... ii EQUIPMENT LISTS... iii 1. INSTALLATION... 1
1.1 Installation of Display Unit...1 1.2 Wiring....3

2. INITIAL SETTINGS... 7

2.1 Data Sentence Description...7 2.2 IEC 61162-1 (NMEA 0183) Input Data Sentences...8 2.3 Setting Input/Output....9
PACKING LIST... A-1 OUTLINE DRAWINGS... D-1 INTERCONNECTION DIAGRAM.. S-1
Your Local Agent/Dealer 9-52 Ashihara-cho, Nishinomiya, Japan Telephone : Telefax : 0798-65-2111 0798-65-4200

All rights reserved.

Printed in Japan
FIRST EDITION : MAR. 2001 E1 : FEB. 03,2003
PUB.No. IME-44130-E1 ( YOSH ) RD-30
*00080917801* *00080917801*

*00080917801*

*IME44130E10* *IME44130E10*

*IME44130E1*

SAFETY INSTRUCTIONS

WARNING

Do not open the cover unless totally familiar with electrical circuits and service manual. Improper handling can result in electrical shock. Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. Be sure that the power supply is compatible with the voltage rating of the equipment. Connection of an incorrect power supply can cause fire or equipment damage. The voltage rating of the equipment appears on the label above the power connector.

CAUTION

Ground the equipment to prevent mutual interference. Observe the following compass safe distances to prevent interference to a magnetic compass: Standard Steering Display unit 0.35 m 0.25 m

SYSTEM CONFIGURATION

FURUNO

MENU DISP

ENT DIM

GPS receiver GP-310B

Multi display RD-30

Sensor

Multi display RD-30 Sensor

Navigator

: Standard : Option

Ship's mains 12-24 VDC

EQUIPMENT LIST

Standard supply

No. Name Multi Display Spare Parts Installation Materials Accessories Type RD-30 SP14-02901 CP14-06000 FP14-02801 Code No. Qty set 1 set 1 set +Tapping screw (4 pcs) MJ-A7SPF0005-020 Hard cover Remarks

Optional supply

No. 3 Name Flush Mount Kit S Flush Mount Kit F Cable Assy. Type OP20-17 OP20-29 MJ-A7SPF0005-020 MJ-A7SPF0006-100 MJ-A7SPF/SRMD-100 Code No. 000-040-720 000-041-405 000-139-384 000-143-578 000-144-Qty 1 Remarks For flush mounting the display unit Power, signal 7P-7P cross cable 7P-7P straight cable

Sensors available

No. 5 Name Smart Sensor Smart Sensor Smart Sensor Smart Sensor Smart Sensor Type 235DT-MSE 235DT-PSE 235DST-PWE 235DHT-LMSE 235DHT-MSE Code No. 000-144-981 000-144-982 000-144-983 000-144-984 000-144-985 Qty 1 Remarks Depth & Temperature Sensor Depth & Temperature Sensor Depth, Speed and Temperature Sensor Depth and High Precision Temperature Sensor Depth and High Precision Temperature Sensor
For technical specifications see Airmars technical data.
This page is intentionally left blank.

INSTALLATION

Installation of Display Unit
The display unit can be installed on a tabletop, on the overhead, or in a panel (optional flush mounting kit required). Refer to the outline drawings at the end of this manual for installation instructions. When selecting a mounting location, keep in mind the following points: Locate the unit away from exhaust pipes and vents. The mounting location should be well ventilated. Mount the unit where shock and vibration are minimal. Locate the unit away from equipment which generates electromagnetic fields such as a motor or generator. Allow sufficient maintenance space at the sides and rear of the unit and leave sufficient slack in cables, to facilitate maintenance and servicing. Observe the following compass safe distances to prevent deviation of a magnetic compass. Standard compass, 0.35 m, Steering compass, 0.25 m.

Mounting considerations

Tabletop and overhead mounting

Tabletop

Overhead
Figure 1-1 Tabletop and overhead mounting methods

Flush mounting

There are two types of flush mount kits, F type and S type. For details, see the outline drawings at the back of this manual. F type Flush mount kit F (Type: OP20-29, Code No.: 000-041-405) No. Name Type Code No. Qty 1 Cosmetic Panel 20-016-1051 100-251-2 + Tapping Screw 5x20 SUS304 000-802-3 Hex Bolt M6x12 SUS304 000-862-4 Spring Washer M6 SUS304 000-864-Remarks
1. Make a cutout of 183 X 92 mm. 2. Attach the cosmetic panel (supplied) to the display unit with hex bolts (M6X12, supplied) and spring washers (M6, supplied). 3. Fix the display unit to the mounting location with four tapping screws (5X20, supplied). S type Flush mount kit S (Type: OP20-17, Code No.: 000-040-720) No. Name Type Code No. Qty 1 Fixing Metal 20-007-2401 100-183-2 Wing Bolt M4x30 YBSC2 000-804-MBNHex Bolt M6x12 SUS304 000-862-4 Wing Nut M4 YBSC2 000-863-MBNSpring Washer M6 SUS304 000-864-Remarks
1. Make a cutout of 167 X 92 mm. 2. Attach two fixing metals (supplied) to the display unit with hex bolts (M6X12, supplied) and spring washers (M6, supplied). 3. Screw four wing bolts (supplied) into wing nuts (supplied). 4. Fasten the display unit to the mounting location with four sets of wing bolts and nuts assembled at step 3.

Wiring

The figure below shows where to connect cables on the rear of the display unit.

GPS RECEIVER

DISPLAY UNIT
DISPLAY UNIT 1A FUSE (+ Line) Black POWER Ground (12-24 VDC) + Red
Ground the equipment to prevent mutual interference.
Figure 1-2 Wiring Note: The fuse holder contains a spring which fixes the fuse. To prevent detachment of the spring, which would cause loss of power, tie the line as shown in Figure 1-3.

Fuse holder + line (red)

Tie here.
Figure 1-3 How to fix spring in fuse holder

Grounding

The display unit contains a CPU. While it is operating, it radiates noise, which can interfere with radio equipment. Ground the unit as follows to prevent interference: The ground wire should be 1.25 sq or larger. The ground wire should be as short as possible. The signal ground and frame ground are separated, however the power line is not isolated. Therefore, do not connect the signal ground to the frame ground when connecting other equipment to a positive ground battery.

External equipment

The power supply port (IN/OUT port) is commonly used for connection of external equipment such as navigation equipment or a PC. Refer to the interconnection diagram on page S-1 for connection. IN/OUT port Connector 1 TD-A 2 TD-B 3 RD-H 4 RD-C 5 +V 6 GND 7 FG Remarks IEC61162-1/NMEA 0183 IEC61162-1/NMEA 0183 Power supply (1224VDC) (INPUT)

AUX port Connector 1 TD-A 2 TD-B 3 RD-H 4 RD-C 5 +Vout 6 GND 7 FG Remarks IEC61162-1/NMEA 0183 IEC61162-1/NMEA 0183 Max 300 mA (OUTPUT)

One Display Unit

MENU DISP ENT DIM

NMEA 0183 POWER OUT

SENSOR NMEA 0183

IN/OUT

12-24 VDC

Two Display Units

GP-310B

AUX No. 1

RD-30 PWR

Ship's battery 12-24 VDC

Max. 20 m Note2

Three Display Units

Max. 20 m Ship's battery 12-24 VDC Note2
Note1: A set of one GP-310B and three RD-30 can be powered with 12-24 VDC power. Note2: For cable length up to 10 m use cable type MJ-A7SPF0006-100 (cross cable), and for cable length 10-20 m use cable type MJA7SPF0006-100 (cross cable) and MJ-A7SPF/SRMD-100 (straight cable). Maximum length between the units is 20 m.
Note3: Turn on display units in sequential order. Note4: Refer to the following table to connect a sensor other than the GP310B. Do not exceed the maximum output current and the output voltage range. One RD-30 Maximum Output output voltage range current 300 mA 10.0-14.9 V 300 mA 21.0-30.5 V Two RD-30 Maximum Output output voltage current range 180 mA 9.2-14.4 V 180 mA 20.4-30.2 V Three RD-30 Maximum Output output voltage current range 60 mA 8.7-14.1 V 60 mA 20.4-30.3V
Ships Battery 12 VDC 24 VDC
Fox example, in the three display units connection, a sensor with maximum current 60 mA and input voltage range 8.7-14.1 V or 20.4-30.3 V can be connected.

INITIAL SETTINGS

This equipment can input and output navigation data to external equipment in IEC 61162-1 (NMEA 0183) format. Input data is output as raw data. For output setting, refer to the operators manual of the equipment.
Data Sentence Description
APB: BWC: BWR: COG: DBK: DBS: DBT: DPT: GGA: GLC: GLL: GTD: HDG: HDM: HDT: MDA: MTW: MWV: RMB: Autopilot sentence data Range and bearing to waypoint (great circle navigation) Range and bearing to waypoint (rhumb line) Course over ground Depth Depth Depth below transducer Depth GPS position fixing condition (time of fix, latitude, longitude, receiving condition, number of satellites used, DOP) Geographic position Loran-C Latitude and longitude Loran-C time difference Heading, deviation and variation Heading, magnetic north Heading true Wind direction and speed Water temperature Wind direction and speed Generic navigational information (cross track error, steering direction, starting waypoint no., destination waypoint no., latitude and longitude of starting waypoint, latitude and longitude of destination waypoint, range and bearing to waypoint, range and bearing from present position to destination waypoint, velocity to destination, arrival alarm) Generic navigational information (UTC time, latitude, longitude, ground speed, true course, day, month, year) Rate of Turn Water speed and ground speeds Tidal current direction and current speed Water speed and heading Actual track and ground speeds Relative wind direction and speed Actual wind direction and speed Course error amount and direction to steer UTC time (day, month, year)

RMC: ROT: VBW: VDR: VHW: VTG: VWR: VWT: XTE: ZDA:
IEC 61162-1 (NMEA 0183) Input Data Sentences
The AUX port has priority when the same data sentences are input at it and the IN/OUT port simultaneously. > = Priority order Position: GGA>RMC>GLL Time: ZDA>GGA Speed over ground: VTG>RMC>VBW Speed through water: VHW>VBW Wind speed, direction: True: MWV(T)>VWT>MDA Apparent: MWV(R)>VWR Water temperature: MTW>MDA Depth: DPT>DBT >DBS >DBK Course: VTG>RMC Heading: HDT>HDG>HDM>VHW Waypoint: RMB>BWR>BWC Current set and drift: VDR Atmospheric pressure: MDA (Bar>Inch, converted to hPa) Humidity: MDA (True>Relative) Cross-track error: XTE>APB>RMB Time difference: GLC>GTD Temperature: MDA Rate of Turn: ROT

Setting Input/Output

The I/O SETUP menu sets up the IN/OUT and AUX ports on the RD-30. Additionally you can use this menu to output power to other display units, in case of multiple display units. Note: Note that the equipment can process data input at the rate of up to 430 characters/second. Some delay will occur when processing data input at a higher rate. 1. Press the [MENU] key once or twice to open the main menu. 2. Select I/O SETUP and then press the [ENT] key.

I/O PORT SETUP

IN/OUT PORT : OFF AUX PORT : OFF POWER OUT : OFF < SELECT SENTENCE > IN/OUT PORT AUX PORT
Figure 2-1 I/O PORT SETUP menu 3. Select IN/OUT PORT, AUX PORT or POWER OUT as appropriate and then press the [ENT] key. One of the following displays appears depending on your selection.

OFF IN/OUT AUX BOTH

IN/OUT and AUX options

OFF ON

POWER OUT options
OFF: No output ON: Outputs power to other display units
OFF: No output IN/OUT: Output data which is input through the IN/OUT port. AUX: Output data which is input through the AUX port. BOTH: Output mixed data which is input through the IN/OUT and AUX ports.
Figure 2-2 IN/OUT PORT, AUX PORT and POWER OUT options Note: If, when BOTH is selected, the data sentence which has an input interval faster than one second (ROT, HDT, etc.) is turned on, some data may not be output. 4. Select appropriate option and then press the [ENT] key. 5. When OFF, IN/OUT or AUX is selected for the IN/OUT or AUX port, go to step 8. When BOTH is selected for IN/OUT or AUX port, select IN/OUT PORT or AUX PORT of the SELECT SENTENCE and then press the [ENT] key.

IN/OUT PORT

APB BWC BWR DBK DBS DBT DPT : : : : : : : OFF OFFOFF OFF OFF OFF OFF OFF 00/08 APB BWC BWR DBK DBS DBT DPT

AUX PORT

: : : : : : : OFF OFFOFF OFF OFF OFF OFF OFF 00/08
Number of sentences currently turned on
Figure 2-3 IN/OUT PORT and AUX PORT menu Note: Sentences currently being received are shown in reverse video. 6. Select sentence to output and then press the [ENT] key. Use to scroll the display.
Figure 2-4 IN/OUT PORT and AUX PORT options 7. Select ON or OFF as appropriate and then press the [ENT] key. You can turn ON up to eight sentences. 8. Press the [MENU] key twice to close the menu. See the next page for examples of port settings.

GP-310B AUX

FURUNO FURUNO

L/L POWER

MENU ENT DIM

L/L POWER L/L

IN/OUT Ship's battery 12-24 VDC IN/OUT: OFF AUX: OFF POWER OUT: ON
IN/OUT: AUX AUX: OFF POWER OUT: ON
DEPTH TEMPERATURE AUX GPS L/L PLOTTER

E/S L/L

DEPTH TEMPERATURE IN/OUT: AUX AUX: IN/OUT POWER OUT: OFF

PLOTTER L/L POWER

GPS PLOTTER AUX L/L

MENU ENT DIM DISP

DEPTH E/S L/L

L/L L/L

IN/OUT Ship's battery 12-24 VDC IN/OUT: OFF AUX: AUX POWER OUT: ON

IN/OUT L/L DEPTH

IN/OUT: BOTH AUX: IN/OUT POWER OUT: ON
IN/OUT: AUX AUX: IN/OUT POWER OUT: OFF
GP-310B L/L L/L LORAN C PLOTTER Note: For "BOTH," select sentences to receive with "SELECT SENTENCE" on the I/O SETUP menu.
L/L IN/OUT Ship's battery 12-24 VDC IN/OUT: BOTH AUX: OFF POWER OUT: ON
Figure 2-5 Example of I/O PORT SETUP

N A M E

MULTIDISPLAY 000-041-574 **

14CJ-X-9851 -4

O U T L I N E UNIT

DESCRIPTION/CODE

RD-30-E

SPARE PARTS

FGMB 1A 125V

SP14-02901

2 000-114-805

COVER

ACCESSORIES

20-016-1091-2

FP14-02801

1 100-297-032

MJ CABLE ASSY.

INSTALLATION MATERIALS

MJ-A7SPF0009-020

CP14-06000

1 000-145-612

+ +TAPPING SCREW

5X20 SUS4 000-802-081
3.-[**]- CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.

Jan. 31, '03

Navigational data organizer

REMOTE DISPLAY UNIT

Model RD-30

Speedometer

Anemometer
I Organizes operation of GPS, VideoPlotter, radar, echo sounder, etc. for user's preference I NMEA 0183 or IEC 61162-1 digital interface I Positive display of own ship position, speed, course, water temperature, depth, speed and direction of current and wind
The RD-30 is a navigational data organizer that allows the operator to select the preferred display from interfaced equipment such as GPS, VideoPlotter, Radar and echo sounder, autopilot and various sensors for water temperature, tide and wind. The compact, high contrast Silver Bright 4.5" LCD may be installed in a limited space, remote from its source.
I AIRMAR Smart SensorTM providing water temperature, water depth and speed relative to water I Audible alarms for course error, ship speed, cross track error, temperature, depth, arrival I High contrast 4.5" Silver Bright LCD display, night and day light viewable
Five display modes are available including Speedometer, Highway and Text. The text mode presents up to four of the most necessary types of data. The display layout can be customized for your specific needs. AIRMAR Smart SensorTM is available. It contains the functionality of measuring water temperature, water depth, speed relative to water, and NMEA interface all in one and is connected to the RD-30 with a single cable.

www.furuno.com

SPECIFICATIONS OF RD-30
1. Display Unit 4.5-inch monochrome LCD (8 gray tones) 120 (V) x 64 (H) pixels 2. Display Mode Highway, Graphical, Speedometer, Text mode, Anemometer 3. Alarm Water temp, Depth, Speed, Time, Anchor watch, Distance run, Cross track error 4. Correction Manual correction for Water temp, Depth, Speed, Wind 5. Interface Input/Output (NMEA 0183) BWR, CUR, DBK, DBS, DBT, GGA, GLC, GLL, GTD, HDG, HDT, HDM, MDA, MTW, MWV, RMB, RMC, ROT, VBW, VDR, VTG, VHW, VWT, VWR, ZDA 6. Power supply 12-24 VDC, 200-105 mA Display Unit
0.6 kg 1.3 lb 209 8.2" 175 6.9" 125 4.9" 100 3.9" 85 3.4" 78 3.1"

15 0.6"

4- 6 (140 5.5")

(32 1.3")

Flush mount kit F-type
17 0.7" 4- 5.5.1" (112 4.4") 205 8.1" 68 2.7"

61 2.4"

(187 7.4") 92 3.6"

EQUIPMENT LIST

Standard 1. Display Unit RD-unit 2. Standard Spare Parts and Installation Materials 1 set Option 1. Flush mount kit for display S type (OP20-17), F type (OP20-18/29) 2. Extension Cable for sensor MJ-A7SPF/SRMD-100 ENVIRONMENT Climatic and EMC: IEC 60945 Waterproofing IPX5 (IEC 60529), CFR-46 (USCG)
Cutout for flush mount 183 7.2"

Flush mount kit S-type

15 0.8" (50 2.0") 215 8.5" 70 2.8"

70 2.8"

63 2.5"

12 0.5"max

4- 5.3.6"
Cutout for flush mount 167 6.6"
Lineup of AIRMAR Smart Sensor
Type 235DT-MSE 235DT-PSE 235DST-PWE 235DHT-LMSE 235DHT-MSE Remarks Depth & Temperature Sensor Depth & Temperature Sensor Depth, Speed and Temperature Sensor Depth & High Precision Temperature Sensor Depth & High Precision Temperature Sensor

Interconnection Diagram

RD-30 Display Unit RD-30 IEC 61162-1 NMEA 0183 DGPS/GPS Echo sounder Videoplotter Radar Autopilot
Smart SensorTM is a trade mark of AIRMAR, registered in U.S. and other country.

IEC 61162-1 NMEA 0183

12-24 VDC OPTION Sensor
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
ALL BRAND AND PRODUCT NAMES ARE REGISTERED TRADEMARKS, TRADEMARKS OR SERVICE MARKS OF THEIR RESPECTIVE HOLDERS FURUNO ELECTRIC CO., LTD. FURUNO FRANCE S.A.S. FURUNO NORGE A/S
Nishinomiya, Hyogo, Japan Phone: +81 (0)798 65-2111 Fax: +81 (0)798 65-4200, 66-4622 Bordeaux-Mrignac, France Phone: +Fax: +lesund, Norway Phone: +102950 Fax: +102951

FURUNO POLSKA Sp. Z o.o.

Gdynia, Poland Phone: +20 Fax: +21
Catalogue No. N-845f 09023SS Printed in Japan

FURUNO U.S.A., INC.

Camas, Washington, U.S.A. Phone: +1 360-834-9300 Fax: +1 360-834-9400