Preface
Copyright 2004 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

AutoCAD and Autoshade are trademarks of Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International Business Machines Corp. Lotus, 1-2-3, and Symphony are trademarks of Lotus Development Corp. Windows, Word, MS-DOS, and Microsoft are trademarks of Microsoft Corp. VESA is a trademark of Video Electronics Standards Association. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Limitation of Liability

While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein.

600L i

Notices Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help

Notice:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: I/P: 100-240 Vac, 50-60Hz, 1.5A O/P: 19Vdc, 3.4A There is no internal power supply.

Table of Content

Chapter 1: Before you Start --------------------------------------------- 1 Conventions of This Manual... 1 Safety Precautions.... 1 Wichtige Sicherheitshinweise... 3 Things you must remember before working on your computer.. 6 Chapter 2: Introduction --------------------------------------------------- 9 Welcome to the Notebook PC... 9 Unpacking the Notebook.. 9 Getting to Know Your Computer.. 10 Chapter 3: Getting Started ----------------------------------------------- 19 Connecting to a Power Source... 19 Turning On Your Notebook Computer... 20 Inserting and Removing the Battery Pack... 21 Charging the Battery Pack... 22 Chapter 4: Using the Notebook Computer-------------------------- 23 Adjusting the LCD Screen Display... 23 The TouchPad... 26 Data Storage and Retrieval... 26 Power Saving Modes... 27 Resetting the System... 30 Chapter 5: Desktop Operation ------------------------------------------ 31 Audio... 31 Connecting Peripheral Devices.. 32 Chapter 6: Internet Connection ---------------------------------------- 35 Using Both DHCP and Static IP for Connection to Internet. 38 Using Wireless LAN Network for Connection to Internet (Microsofts Service Pack 2) (Optional)... 40 Chapter 7: Configuring and Maintaining your System ---------- 41 Introduction... 41 Chapter 8: Microsoft Center Edition (MCE) (Option) ----------- 49 Windows XP Media Center Edition (MCE).. 49 MCE Application Sound Adjustment.. 50 If you are using MCEs My TV application.. 50 If you are using InterVideos WinDVR application.. 51 Chapter 9: VGA Utilities -------------------------------------------------- 53
ATI OpenGL... ! ATIs Display... ! Color.... ! Options... ! Overlay... ! ATI PowerPlay... ! Direct 3D... ! Chapter 10: Viewing Live Video (Option) --------------------------- 61 Using the Remote Control... 62 WinDVR Mode... 62 Application buttons in DVR mode.. 64 Application buttons in DVD mode.. 66 Application buttons in Music mode... 68 Chapter 11: Troubleshooting ------------------------------------------- 69 Locating a Problem... 69 Checking Cables and Connections.. 69 The Power-On Self Test... 70 General Hardware Problems.. 71 Contacting Your Dealer... 72 Chapter 12: How do I Expand my Notebook----------------------- 75 Upgrading your Memory.. 76 Easy to Upgrade HDD Module... 77 Chapter 13: Specification ------------------------------------------------ 79 Detailed Notebook Specifications... 79
Canadian DOC Notice For Class B Computing Devices

This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations. Cet appareil numerique de la classe B repecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

Personal Inventory

This Notebook computer system is designed for years of productive and pleasurable computing. Use this section to keep notes about details of your purchase. Update this section when you add new options. Date of Purchase: Dealers Name: Phone: Address: E-Mail Address: WWW Site: Serial Number: CPU Type: Hard Disk Capacity: Memory Capacity: Optional Equipment:

BEFORE YOU START

Conventions of This Manual
Use this manual will help you get the most from your notebook computer. If you are an experienced user of computers and/or Microsofts Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. If you are a less experienced user, you should through the manual carefully before using your system. Whether or not you are an experienced user, you should consult on the Troubleshooting Chapter if you encounter any problems with your notebook.

Safety Precautions

This section is designed to assist you in identifying potentially unsafe conditions while working with this product. Required safety features have been installed in the computer to protect you from injury. However, you should use good judgment to identify potential safety hazards: 1. Please read these safety instructions carefully. 2. Please keep this User's Manual for later reference. 3. Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning. 4. For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible. 5. Please keep this equipment from humidity. 6. Lay this equipment on a reliable surface when installed. A drop or fall could cause injury. 7. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet.

8. 9. 10. 11. 12. 13.

15. 16. 17.
Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. All cautions and warnings on the equipment should be noted. If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage. Never pour any liquid into the opening, this could cause fire or electrical shock. Never open the equipment. For safety reason, the equipment should only be opened by a qualified service personnel. If on the following situations arises, get the equipment checked by a service personnel: a. The Power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment has not worked well or you cannot get it work according to the user's manual. e. The equipment has dropped and damaged. f. If the equipment has obvious sign of breakage. Do not leave this equipment in an environment unconditioned, storage temperature above 60C (140f), it may damage the equipment. The unit can be operated at an ambient temperature of max. 35C. The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A). Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection. The cord set must be approved for the country in which it is used. The appliance coupler must have a configuration for mating with a CEE22/EN6032/IEC 320 appliance inlet. A. For U.S. and Canada: The cord set must be UL Listed and CSA Certified. The minimum specifications for the flexible cord are No. 18 AWG. B. For Japan:

Try to avoid the computer components from being destroyed if it is over heated, so try to allow plenty of room for air to circulate around the case. Do not block the ventilation opening. Do not place your computer in direct sunlight. Suitable place to work Your computer will run well wherever youre comfortable but extremes of temperature and humidity can be challenging to your systems parts. There are some things you can tolerate that the computer cant things like static electricity, dust, water, steam and oil. In case you decide to pull over for roadside computing, try to choose a clean, comfortable work area for your system. A lithium-ion battery pack will be available when you are traveling. If you are running your system for the first time on battery power, remove the battery from the package, install it into the system and recharge the battery to fully prepare for service.

INTRODUCTION

Welcome to the Notebook PC
Congratulations on your purchase of the Notebook PC. Your Notebook features the latest advances in portable computing technology. The Notebooks modular design provides maximum expandability without compromising portability. The high-performance CPU and enhanced IDE hard drive provides you with extra processing power for handling complex graphics and running large programs. A premium notebook designed for successful executives who demand the very best and featuring ultimate power, ultimate wide screen display, ultimate AV capabilities and ultimate connectivity. A Media solution is a combination of Windows XP software augmented by InterVideo WinCinema including WinDVR for watching television, WinDVD for viewing movies and WinRIP for playing music.

Unpacking the Notebook

The Notebook comes securely packaged in a sturdy cardboard shipping carton. Upon receiving your Notebook, open the carton and carefully remove the contents. If anything is missing or damaged, please contact your Notebook dealer immediately. The shipping carton should contain the following items: The Notebook computer An AC adapter An AC power cord Software Drivers CD Do not throw the packaging materials away. You may need them later if you have to ship the computer for repairs.

Cable TV Input

Before connecting the cable into the connector, be sure to remove first the cover on the cable TV connector at the rear of the computer with the aid of a screw driver. One more thing that you need to be aware of is to know the video standard being used in your country that you are viewing. This system supports 3 video standard namely: NTSC, PAL and SECAM. For detailed information on the proper connection of the cable TV, please refer to Chapter 9 on Viewing Live Video. 2. USB Ports

The Bottom Panel

1. 2. 3. 4. 5.
Expansion Compartment Hard Disk Optical Drive CPU Compartment Battery Release Latch

Battery Lock Battery

Page intentionally left blank

GETTING STARTED

Connecting to a Power Source
Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computers battery pack. The adapters AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. The power cord for the AC adapter requires a three-hole grounded AC outlet. To connect the computer to an external power source: 1. Plug the AC adapters connector into the DC-IN connector at the left side of the computer. 2. Connect the power cord to the AC adapter and then to a wall outlet.
Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices. Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery. Never turn off or reset your Notebook while the hard disk is in use and the HDD status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebooks electrical circuitry.
Turning On Your Notebook Computer

Turn on your Notebook by pressing the power button. Hold the button down for a 1 or 2 second and release. The Power-On Self Test (POST) runs automatically. After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as booting a computer). If your OS (Operating System such as Windows XP etc) is installed, it should start automatically. To turn the Notebook off, save your work and close all open applications, click on Start, then select the Turn off the computer. A selection box will be displayed and click on the Turn Off button to shut down your computer. When your computer hangs up, press the power button for 4-6 seconds to shut down the computer. Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer for approximately 2 hours under the following conditions: The battery pack initially has a full charge. No peripheral devices are installed. The disk/DVD-ROM drives run no more than 10% of the time. 20
Only use batteries that are approved by an authorized dealer for this model only. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions.
Inserting and Removing the Battery Pack
The battery pack should already be inserted in your Notebook computer when you unpack it. If not inserted, follow these directions:
To remove the battery pack:
Charging the Battery Pack
The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. If this is your first time to use the battery, be sure to fully discharge the battery and recharged until it is fully charged.
USING THE NOTEBOOK COMPUTER
Adjusting the LCD Screen Display
The LCD screen display can be adjusted by the following key combinations. KEYS FUNCTIONS [Fn] + [F7] [Fn] + [F8] Decreases the brightness level. Increases the brightness level.

Power Saving Modes

This section contains information on the Notebooks power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system. The AC Adapter converts AC power from a wall outlet to the DC power required by the computer. The Battery Power System A fully charged pack will provide approximately 2 hours of battery life depending on your system configuration application it runs. Before using the computer on battery power for the first time, check the battery status icon on the Windows Toolbar to make sure the battery is fully charged. See Battery Status later in this section for a description and explanation of the Windows Battery icon. Charging the battery takes about 4 hours to charge when the system is in off state. If possible, always charge the battery completely. Removing the Battery Pack To remove the battery pack from its compartment, please refer to Chapter Three, Inserting and Removing the Battery Pack.
Preparing the Battery Pack for Use Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: Insert the battery into the battery compartment and turn on the Notebook. If the battery is completely without power go to the next step. Otherwise, let the battery run down until the battery low-low warning beeps are heard. The system will automatically enter Suspend mode. 2. Turn the Notebook off. Connect the AC adapter and let the battery fully recharge. When the battery charge indicator turns off, the battery is fully charged. 3. Turn On the notebook, let the battery run down until the battery is in low-low state and you hear a warning beeps. The system will automatically enter the Suspend mode. You can now connect the AC adapter. 4. The battery pack is now calibrated properly. In general, using the battery until the low-low battery-warning indicator appears and fully recharges the battery each time (full discharge/charge cycle) will ensure the accurate reporting of the battery gauge status. Automatic Battery Pack Charging Function You can automatically charge the battery pack by using the AC Adapter. The charge time is about 4 hours when the Notebook power is turned off. The following table summarizes the charging modes: Charge Mode Charge Time Fast 4 hours with the system off or in Suspend mode. The temperature must be 25C or below room temperature. A pre-charge is supplied to the Li-Ion battery pack. 1.

Pre-Charge

Battery Status Windows XP has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the Notebook is running on battery power or is attached to the AC adapter. This applet also displays a meter that indicates how much charge is remaining in the battery. 28

Battery Low Warning When the pack initially reaches the Battery Low state approximately 7 ~ 10 minutes of the usable battery life is left. You will hear an audible beep signal every 1.5 seconds alerting you to the Battery Low status. When the battery power reaches the Battery Low Low status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data. Sound Meaning Continuous beeping every 1.5 seconds Beeping accelerates Battery Low: Indicates that there is 7 to10 minutes charge remaining. Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the Notebook, or connect the AC adapter.
When there is only one minute of battery charge remaining, the Notebook will enter suspend mode or hibernate according to Windows setting. You should connect AC power and resume to save your work. Small Battery for the Real Time Clock There is a small built-in battery pack that supplies power to the system in order to maintain certain system information while the power is off. If the Notebook is left without a power source for long period of time, this battery will be exhausted and system information will be lost. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. Battery Calibration The purpose for this process is to provide a long battery life for your system battery pack. 1. Turn on the computer, when the text appears, press [Del] or the [Delete] key until the system enters the BIOS Setup screen, you may now make the necessary changes. 2. Press the arrow key until it reaches the Exit menu screen. Again press the arrow key and select the Battery Calibration item. 29

3. 4. 5. 6.

Press the [Enter] key and disconnect the AC adapter then press the [Y] key until you hear continuous battery low-low warning beeping sounds. The system will be fully discharge and shutdown completely. Connect the AC adapter and let the battery fully recharge. The Battery Charge LED which is located at the left side of the notebook will light indicating it is in charging status. When the battery charge LED turns off will indicate the system is fully charged. Repeat step 1 to 4 once again. The battery is now fully calibrated.

Resetting the System

After installing a software application package, you may be prompted to reset the system to load the changed operating environment. To reset the system, or reboot, press the [Ctrl] + [Alt] + [Delete] keys simultaneously. This is known as warm boot. This key combination acts as software reset switch when you encounter hardware or software problems, which lock up the Notebook. If this key combination does not shut down the Notebook, you can reset the Notebook by using the Notebooks power button. Should the Notebook lock up for some reason, pressing this button powers the Notebook off. Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F7] key to reduce the brightness or [F8] to increase the brightness.

DESKTOP OPERATION

This chapter discusses those functions of your notebook that are typical of desktop systems.
The Multimedia Sound System The Notebooks built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software. The Notebook is equipped with internal stereo speakers, a microphone, and input audio ports for external audio units. An external microphone can be connected to the microphone jack. External speakers or headphones can be connected to the Notebooks audio-out jack. External audio devices can be connected to the Line in jack. Audio Volume Control The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key combination decreases the audio output volume; press the [Fn] + [F4] hot-key combination increases the audio output volume. Audio Software Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through the built-in speakers or through external speakers connected via the system ports. Sound Recording Your system allows you to record sounds and store them as files using the microphone via the microphone jack on the rear of the notebook computer. Check the Windows Help and Support Center in Windows for information on using the various elements in sound recording.
For a high-quality sound, click on the "Volume Control" at the lower right end of your screen. From the Volume Control windows, click on the "Advanced" tab, click and select the "Microphone Boost" item. Playing Sound Files Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check the Help and Support Center in Windows for information on the functions of the Media Player. External Speakers and Microphone The sound system is capable in providing high-quality sound to external speakers and receiving and processing sounds from an external microphone or external sound source.

Alternate Key

Function Scrolls backward through the values for the highlighted field. Scrolls forward through the values for the highlighted field.

PgUp PgDn

Moves the cursor to the field at the top of the window. Moves the cursor to the field at the bottom of the window. Sets the parameters for the current menu to their default values. Save and Exit. Will select a sub menu or show a range of options for a field.
F10 Enter Launching Submenus
Note that a right pointer symbol appears to the left of certain fields. This pointer indicates that a submenu can be launched from this field. A submenu contains additional options for a field parameter. To call up a submenu, simply move the cursor to highlight the field and press the [Enter] key. Use the [Esc] key to return to the Main menu. General Help In addition to the Item Specific Help window, the BIOS Setup program also provides a General Help screen can be called up from any menu by simply pressing [F1]. To exit the help window, press the [Enter] or the [Esc] key. Save Changes and Exit the Setup Program Refer to the Exit menu section of this chapter for detailed information on saving changes and exiting the setup program.
The Main Menu When the Setup program is accessed, the following screen appears:
The Advanced Menu Selecting Advanced from the menu bar displays the advanced menu:
If your system support InterVideo application, select the InterVideo item from the Shortcut Key Working With selection menu. If your system supports the WinXP MCE application, select the WinXP MCE item from the Shortcut Key Working With selection menu. If your system supports the CyberLink application, select the CyberLink item from the Shortcut Key Working With selection menu. (Optional)
The Security Menu The Notebooks advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program.
The Boot Menu The Boot menu allows the user to specify the order in which the Notebook is to check for a device to boot the system. You can also configure the way that the system will boot up. To make changes, select Boot from the menu bar. The following screen appears:
Use the up and down arrows to select the boot device. Then press either the plus key [+] to move the device up the list or the minus key [-] to move the device down the list.

The Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu:
MICROSOFT CENTER EDITION (MCE) (OPTION)
Windows XP Media Center Edition (MCE)
The Windows MCE is a complete software for home PC operating system for you to enjoy entertainment choices together in one place easily accessible from anywhere in the room. This will benefits the consumers to enjoy Media Center experience in their own living room. For more information on the function of the MCE, please refer to the Microsofts Windows XP MCE users guide that goes along with your software package.
Please be advice that when you received your computer, the MCE port at the right side.
MCE Application Sound Adjustment
This notice only applies to those systems that only support MCE application when you are using the Windows volume adjustment function. From your Windows, click on the lower left corner of the screen the speaker icon and open the Volume Control Properties Window.
If you are using MCEs My TV application
1. 2. Use your mouse right button to click on the Volume icon and select the Open Volume Control item. The Volume Control display window is displayed on your screen.
Click on the Options tab and select the Properties item.
From the Properties display window, enable the Aux item and click OK. The Aux is now added on the Volume Control window.
Enable the Mute tab on the Aux item and close the window.
If you are using InterVideos WinDVR application
The procedures are almost the same as those mentioned above from steps 1 to 5 to adjust the volume control. On step 6, disable the Mute tab on the Aux item and close the window.

VGA UTILITIES

click on the Display icon. From the Display Properties window, select the Settings tab and click on the Advanced tab to enter the Digital Flat Panel (1024x768)on Mobile Intel 915GM/GMS,910ML Express Chipset Family" window.

Application buttons in DVR mode
TV - Launch the WinDVR application Channel Surfing - Surf channels by displaying 16 channels at once. Full screen - Change display size to full screen. Mute - Mute or restore sound when watching TV. C.C. (Close Caption) - Display overlay text caption. MTS/SAP - Switch TV sound mode to mono stereo or SAP Scan (Auto scan) - Scans all available channels for context. Arrow Up and Down - Navigates up or down. Arrow Left and Right - Navigates left or right. Cancel - Cancel last operation. Select - Selection.
CH Up & Down - Selects next higher or lower channel in channel memory. Replay Playback previous sequel after pressing the TimeShift. Skip - Skip the recorded program. Volume (Volume up and down) Increase and decrease sound. Stop - Stops functions such as record, play, rewind, forward and pause. Play/Pause - Plays or pauses a scene. Record - Records TV and encodes it into MPEG I/II format. TimeShift - Pauses live TV. Real Screen (Go Live) Stop timeshift. Snapshot - Captures a favorite screen shots from the program. Numeric Keypad (0-9) - Select a channel up to 99 by pressing two numbers.
Application buttons in DVD mode
DVD - Launch the WinDVD application. Audio Selection - Selects a language. Subtitle - Activates language subtitles. Full screen - Change display size to full screen. Angle (Angle Selection) - Allows multiple angle viewing Mute - Mute or restore sound when watching CD title or MPEG file. Arrow Up and Down - Navigates up or down. Arrow Left and Right - Navigates left or right. Cancel - Cancel last operation. Select - Selection. Speed - Speed up the play. CHAPTER (Previous & Next) Selects previous or next chapter. Volume (Volume up and down) Increase and decrease sound. REW - Play disc in fast reverse mode. FWD - Play disc in fast forward mode. Stop - Stops the current play. Play/Pause - Starts or pause the disc. Step Forward Single frame advance while in pause mode. Bookmark - Instantly mark your favorite scene. Menu - Opens DVD title main menu. SnapShot - Captures still images of current playback. Numeric Keypad (0-9) - Inputs chapter number to playback.
Please take note that when you are playing the DVD applicaton, you will only be able to use the Remote Control DVD button if your system support the InterVideo WinCinema application.If your system support the WinXPMCE application, you will have to use the Microsoft Remote Control that comes with your package. Use Lunch key to chosoe between these two applications, please proceed to BIOS Setup and select the Advanced menu. From the Shortcut Key Working With selection item, select the InterVideo if your system only support the InterVideo application or the WinXP MCE application if your system support the Microsofts WinXP MCE application.

The Power-On Self Test

The Power-On Self Test (POST) runs every time you turn on or reset the Notebook. The POST checks memory, the main system board, the display, the keyboard, the disk drives, and other installed options. A few seconds after you turn on your computer, a copyright message appears on your display screen. A memory test message appears next; as the test continues, memory size increases until all installed memory is tested. Normally, the only test routine visible on the screen will be the memory test. Two classifications of malfunctions can be detected during the POST: Error messages that indicate a failure with either the hardware, the
software, or the Basic Input/Output System (BIOS). These critical malfunctions prevent the computer from operating at all or could cause incorrect and apparent results. An example of a critical error is microprocessor malfunction. Messages that furnish important information on the power-on and boot processes (such as memory status). These non-critical malfunctions are those that cause incorrect results that may not be readily apparent. An example of a non-critical error would be a memory chip failure. In general, if the POST detects a system board failure (a critical error), the computer halts and generates a series of beeps. If failure is detected in an area other than the system board (such as the display, keyboard, or an adapter card) an error message is displayed on the screen and testing is stopped. It is important to remember that the POST does not test all areas of the computer, only those that allow it to be operational enough to run diagnostic programs. If your system does not successfully complete the POST, but displays a blank screen, emits a series of beeps, or displays an error code, consult your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented in the table below: Problem: The capacity of the battery is between 95 to 99% but can not fully charged. Solution: Please discharged to less than 95% of its capacity then recharge the battery. Problem: Failure in the installation of the Audio driver. Solution: Be sure to first remove the current audio device from your system. Please follow the instruction on the installation of audio driver. Problem: The display screen is dark Solution: Make sure that the computer is not in Suspend mode. Check the Brightness controls for the screen. If the controls are turned too far down, the screen will be dark. Problem: An incorrect date and time are displayed. Solution: Correct the date and time using the DOS DATE and TIME commands or the options in the Setup Utility. If the date and time become incorrect after a short time, your CMOS battery may