Anthem service manual

Maestro suspension performance. No brake influence, no pedal kick-back, linear rising rate, superb traction, and absolute efficient pedaling. Rock-solid lateral rigidity which increase sprinting efficiency and tight cornering stability in racing courses and singletrack. The Anthem is built on the basis of our Maestro suspension technology with all the features that meet todays XC racing demand. Aggressive and agile XC racing geometry Lightweight frame design Newly designed rear shock. Works well even when set up with little to no sag without sacrificing the original Maestro suspension performance & characteristics.

TABLE OF CONTENTS

Notice to authorized Giant dealers Spare Parts
Exploded Drawing Spare Parts List
Mounting Bolt Torque Settings Dual Suspension Quick Start Guide
Basic Terms & Shock Set-Up Overview Air Shick Set-up Setting and Adjusting Rebound Damping Front Suspension Travel & Sag Guide

Maintenance

General maintenance Replacement of Rear Shock Replacement of Rocker Arm Replacement of Rear Triangle Replacement of Joint/Clev Replacement of Front Frame

Troubleshooting

Notice to authorized Giant dealers
The Anthem is a new XC racing bike based on the Maestro suspension system. It inherits the strengths of Maestro suspension technology and is tuned and perfected to yield most efficient XC racing machine. The Anthem is designed to get from start to finish fastest, and take the rider to the podium.

WARNING

Please read this service manual carefully. Improper assembly of the rear shock or malfunction of the shock system can be extremely hazardous, and may lead to an accident causing injury or death.
Only Giant Glory, Faith, and AC model bicycles are engineered for use with dual crown suspension forks. Use of dual crown suspension forks on any Giant bicycle other than these models will void the warranty and can result in frame failure, which may cause injury or death. Giant is not responsible for damage or injury resulting from the improper use of dual crown forks.

Spare parts

Seq# 0440 0450
Articl# 12806GU0051A1 12806GU0048A4 12806GU0041A6 12806GU0040A9
(GSC)/no 12806GU0051A1 12806GU0048A4 12806GU0041A6 12806GU0040A9
Name LINK BOLTSET D.LINK BOLT R.FRAME BOLT SHOCK BOLT
Description GS804H ROCK ARM BOLT SET(2+3+4) GS804H DOWN PIVOT BOLT SET(6+7) GS804H R.FRAME PIVOT PARTS SET(2+6) GS804H REAR SHOCK BOLT SET(4+5)
Mounting bolt torque settings
Dual Suspension Quick Start Guide
Basic Terms & Shock Set-Up Overview TERMS Bottomed Out: When a shock absorber or suspension fork (herein after referred to as shock) is compressed completely and all the suspension travel has been used. Compression Stroke: The motion of the shock in response to an impact. Damping: Internal mechanism to control the speed of compression or rebound. PSI: Pounds per square inch Rebound: The extension or return stroke of the shock. Sag: Compression of the shock caused by the riders weight. Spring Rate: The amount of force required to compress the spring. Topped Out: When shock or fork returns to its fully extended position rapidly and produces an audible clunk. SET-UP Please refer to the individual shock manufacturers technical manuals for specific information on how to adjust the shocks on Giant dual suspension bicycle. The shocks on Giant dual suspension bicycle can be adjusted to meet riding style and weight. This booklet is intended as a quick-start guide to help get started. It may take a few rides to find your preferred settings.
Platform Valve On bikes equipped with a Manitou Stable Platform Valve (SPV) rear shock, you can adjust the bikes pedaling efficiency by increasing the air pressure in the SPV air cartridge. Increasing the air pressure will resist pedal-induced bobbing. Decreasing the air pressure will make the suspension more sensitive to small bump forces. Please refer to the individual shock manufacturers technical manual for specific information on how to adjust SPV shock. Sag All Giant dual suspension bikes rely on sag for their suspensions to work efficiently. Please take a few moments to read through this guide to understand sag as it applies to your bicycle. Setting bikes sag will greatly enhance your riding experience and the performance of bicycle. Rebound Damping Rebound damping controls the rate of speed at which the shock returns to its original position after responding to a bump force. Rebound damping prevents the shock from returning to its fully extended position too quickly. This is desirable because it improves the rear suspensions sensitivity to small bumps and the tires ability to stay in contact with the ground. It also helps reduce unwanted motion from the rear suspension when the bike encounters a bump while the rider is seated. Typically, the heavier the rider [and higher the neccessary spring rate], the more rebound damping is required. Please refer to this guide for details on how to set rebound damping date. You should also refer to the individual shock manufacturers technical manual for specific information.

AIR SHOCK SET-UP Giant cross-country and trail bikes feature an air shock equipped Maestro suspension design. All rely on sag for proper riding performance. SETTING AND ADJUSTING MAESTRO (ANTHEM) SAG (air shock) 1. Pump the main air chamber to a psi (pounds per square inch) equivalent to riders body weight. 2. Push the rubber O-ring that is around the shocks shaft all the way against the base of shaft (closest to shock body). 3. Position your bicycle next to a wall so that you can sit on the bike with both feet on the pedals while steadying yourself with one arm. Gently sit on the saddle without bouncing. Dismount gently and look at how far the O-ring has moved down the shaft. Measure distance O-ring has moved.
4. Add or remove air until desired shock movement is obtained. Refer to the Sag Recommenda-tion Guide below for proper sag measurements. Maestro Sag Recommendations: Anthem: 1/4 (6mm) O-ring movement
SETTING AND ADJUSTING REBOUND DAMPING 1. If you are unfamiliar with rebound damping, perform this procedure: With full body weight, push down on the saddle forcefully to compress the shock. Watch (and feel) how the shock rebounds from compression. 2. Next, turn the rebound damping knob clockwise until it stops and compress the shock under full body weight. Note that the shock rebounds very slowly. Next, turn the damping knob counterclockwise a few turns and re-perform your compression testing until the shock rebounds just slightly more slowly than with no damping. 3. To check the rebound damping rate while riding, ride off a curb while seated. The rear suspension should bounce only once upon rebound (the heavier the rider, the more damping will be required). Adjust accordingly to accomplish this motion. If the suspension bounces more than once, turn the damping knob in the appropriate direction until one bounce is achieved.
FRONT SUSPENSION TRAVEL & SAG GUIDE
To determine bikes front suspension travel adjustments and recommended settings, please refer to the fork manufacturers technical manual. A suspension fork is effective at both absorbing bump forces and helping the tire to track the ground for improved traction and braking control. When in active mode, a fork will rely on sag to keep the front tire in better contact with the ground during braking. The chart should be used as a general guideline. AIR SPRUNG FORKS As a general guide, pump the main chamber (main spring) to a psi equal to 70% of your body weight. Ride off a curb or similar object. If there is little or no movement from the fork, decrease psi in 10-psi increments until desired movement is achieved. If the fork bottoms out, increase the psi in 10-psi increments until desired movement is achieved. To check rebound, turn the rebound damping knob (if applicable) counter clockwise until it stops. With full body weight, push down on the fork forcefully with the front brake on and watch (and feel) how the fork rebounds. Turn the rebound damping knob clockwise until the fork rebounds slightly slower than with no damping (the heavier the rider, the more damping will be required). SPRING AND ELASTOMER SPRUNG FORKS Springs on these types of forks are set at the factory. Most have a simple adjuster that allows the rider to make the fork firmer or softer depending on rider weight. The heavier the rider, the firmer the spring setting should be. SUGGESTED FRONT SUSPENSION SAG GUIDE FORK TRAVEL (mm) (ALL TYPES) SAG* (mm) 12-15 12-16 15-20 18-30 29-37 34-50 36-54 40-60

*Manitou Forks with SPV may not sag upon initial rider weight. To check sag on an SPV fork, inflate the main spring cartridge to 70% of riders weight, and the SPV cartridge to 30% of riders weight (check the manufacturers technical info for details).

General Maintenance

Inspect all suspension bolts and tighten if necessary to required torque settings. Do not use high-pressure water sources to wash or rinse bicycle. Doing so can displace any lubricants that are present, as well as possibly forcing water and/or contaminants into the bearing that can harm the pivot and bearing, reduce performance, and cause premature wear. Use only low pressure water, or bucket water with a soft nylon bristle brush and mild dish soap to clean the frame and components. Always use LoctiteTM Primer (#7649) and LoctiteTM blue Removable Threadlock (#242) or similar material on thread of fixing bolts of calipers and rotors during re-assembly.
Replacement of rear shock

Shock mounting bolt

Steps 1: Loosen the shock mounting bolt and remove the shock.
Repeat Step 1 in reverse to reassemble the rear shock.
Recommended torque for the shock mounting bolt is 90-110 kgf-cm.
Replacement of rocker arm
Before dismantling the rocker arm: Remove the rear shock.
Rock arm Rear Triangle Bolt Rock arm Bolt
Step 1: Loosen the bolt and remove the rocker arm.
Repeat Step 1 in reverse to reassemble the rocker arm.
Recommended torque for the rear triangle bolt is 120-150 kgf-cm. Recommended torque for the rock arm bolt is 90-110 kgf-cm. Recommended torque for the shock mounting bolt is 90-110 kgf-cm.
Replacement of Rear Triangle
Before dismantling the rear triangle: Remove the rear wheel set. Remove the crank, chain wheel, chain. Remove the rear brake. Remove the rear ends, derailleur.
Step 1: Loosen the rear triangle bolt and remove the rear triangle.
Repeat Step 1 in reverse to reassemble the rear triangle.
Recommended torque for the rear triangle bolt is 120-150 kgf-cm.
Replacement of Joint/clev
Before dismantling the Joint/Clev: Remove the crank, Remove the chain wheel.

Joint/Clev bolt

Joint/Clev
Step 1: Loosen the Joint/Clev bolt and remove the Joint/Clev.

Rear triangle bolt

Repeat Step 1 in reverse to reassemble the Joint/Clev.
Recommended torque for the rear triangle bolt is 120-150 kgf-cm. Recommended torque for the Joint/Clev bolt is 120-150 kgf-cm.
Replacement of front frame
Step 1: Remove the rear shock, rocker arm. Step 2: Remove the rear triangle (follow rear triangle disassembly steps). Step 3: Remove the saddle, seat post, seat post clamp. Step 4: Remove the front fork, heat parts, stem Step 5: Remove the Joint/Clev (follow Joint/Clev disassembly steps).

Q1: If the frame pivots and links for any looseness or play 1. 2. 3. 4. 5. Make sure that the pivot bolts are tightened to the appropriate torque value If the pivot bolt is not tightened to the apporpriate torque value, unthread the bolt enough to expose the receiving threads on frameset or linkage. Put one drop of blue LoctiteTM on the exposed receiving threads. Tighten the bolt to the appropriate torque value. Wipe off excess blue LoctiteTM on the back of the threads.

OFF ROAD | PERFORMANCE | Competition

ANTHEM X3

FROM WORLD CUP XC RACES, TO MARATHONS, OR WEEKEND EPICS. FOR THOSE WHO DO IT ALL, AND WANT TO DO IT FASTER. ANTHEM X IS THE ANSWER.

SPECIFICATIONS

FRAME DESIGN
Frame Technology AnthemXisthelightestalloyfullsuspensionbikeGianthaseverproduced.It featuresaradicallyFluidFormedALUXXSLtubesetusingthelatest,lightweight copivotdesign,pushingaluminumfullsuspensionbiketechnologytonewlimits ofweight,strengthandperformance. OverDriveheadtubeformaximumfrontendstiffnesswithnoweightpenalty Classic71/73*headtube/seattubegeometryforoutstandingXCracing/riding characteristics IntegratedPowerCorebottombracketforsuperiorframestiffness(AnthemXonly) Poststylerearbrakemountsforpowerful,accuratestopping(AnthemXonly) MegaDriveDowntube/toptubeforunparalleledfrontendstiffness Customwomensgeometryavailable
SIZES COLORS FRAME FORK SHOCK

COMPONENTS

XS:14.5,S:15.5,M:17.5,L:19.5,XL:20.5 Black/Blue ALUXXSLFluidFormedalloyMaestro4.0travel Fox32F100RLw/taperedsteerer&lockout, 4/100mm FoxFloatR GiantConnectoversizealloy670mmx19mmrise GiantConnectoversizealloy,4bolt,8degree GiantConnectoversizealloymicroadjust30.9 Fizi:kTundraw/Manganeserail ShimanoM520SPDclipless ShimanoDeorerapidfire27sp. ShimanoDeore9sp.34.9 ShimanoSLXShadow9sp. ShimanoM445hydraulicw/66boltrotors ShimanoM445hydraulic ShimanoHG509sp.1134T ShimanoHG739sp. ShimanoDeore22x32x44T ShimanoBB71,pressfit GiantSXC2Sport,doublewall,alloy32Hdisc Fr:GiantTracker9mm|Rr:ShimanoM4759spdisc 14/15Gbuttedstainless MaxxisCrossmark26x2.1 Shockpump
HANDLEBAR STEM SEATPOST SADDLE PEDALS

DRIVETRAIN

SHIFTERS FRONT DERAILLEUR REAR DERAILLEUR BRAKES BRAKE LEVERS CASSETTE CHAIN CRANKSET BOTTOM BRACKET

WHEELS

KEY UPGRADES
KEY FEATURES Fox32F100RL,FoxFloatRrearshock ShimanoSLX/Deore27speeddrivetrain GiantConnectBar/Stem/Seatpost RecomendedRetailPriceAU$1,999.00 Note:Freightratestodifferentlocationscanaffecttheretailprice

RIMS HUBS SPOKES TIRES

Price: RRP $ 1,999

EXTRAS