GA-8I915P-MF

Intel Pentium 4 LGA775 Processor Motherboard

User's Manual

Rev. 2202 12ME-8I915PMF-2202
* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!! * The WEEE marking applies only in European Union's member states.

Motherboard GA-8I915P-MF

Motherboard

Jun. 11, 2004

Copyright
(c) 2004 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without Gigabyte's prior written permission. Specifications and features are subject to change without prior notice.
Product Manual Classification
In order to assist in the use of this product, Gigabyte has categorized the user manual in the following: For detailed product information and specifications, please carefully read the "Product User Manual". For detailed information related to Gigabyte's unique features, please go to the "Technology Guide" section on Gigabyte's website to read or download the information you need. For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

Table of Content

GA-8I915P-MF Motherboard Layout.... 6 Block Diagram.... 7 Chapter 1 Hardware Installation... 9
1-1 1-2 1-3 Considerations Prior to Installation... 9 Feature Summary... 10 Installation of the CPU and Heatsink.. 12
1-3-1 1-3-2 Installation of the CPU.... 12 Installation of the Heatsink.... 13

1-4 1-5 1-6 1-7

Installation of Memory... 14 Install expansion cards... 16 I/O Back Panel Introduction... 17 Connectors Introduction.... 18
Chapter 2 BIOS Setup... 29
The Main Menu (For example: BIOS Ver. : F4).. 30 2-1 Standard CMOS Features.... 32 2-2 Advanced BIOS Features... 34 2-3 Integrated Peripherals... 36 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 Power Management Setup.... 39 PnP/PCI Configurations... 41 PC Health Status... 42 MB Intelligent Tweaker(M.I.T.)... 43 Load Fail-Safe Defaults... 44 Load Optimized Defaults... 44 Set Supervisor/User Password... 45 Save & Exit Setup.... 46 Exit Without Saving.... 46
Chapter 3 Install Drivers... 47
3-1 3-2 3-3 3-4 3-5 Install Chipset Drivers... 47 Software Applications... 48 Driver CD Information... 48 Hardware Information... 49 Contact Us.... 49
Chapter 4 Appendix.... 51
4-1 Unique Software Utilities... 51
4-1-1 4-1-2 4-1-3 4-1-4 EasyTune 5 Introduction... 52 Xpress Recovery Introduction... 53 Flash BIOS Method Introduction.. 56 2- / 4- / 6- / 8- Channel Audio Function Introduction.. 65

Troubleshooting.... 69

GA-8I915P-MF Motherboard Layout

KB_MS SPDIF_O SPDIF_I

CPU_FAN

IT8712

LGA775 R_USB ATX_12V

USB LAN

Intel 915P

AZALIA_FP

AUDIO1 AUDIO2

PCIE_16

DDR1 DDR2 DDR3 DDR4
PCI1 RTL8110S PCI2 TSB43AB23 CD_IN PCIE_1 COMB F2_1394 F1_1394

BAT CLR_CMOS

S_ATA3 S_ATA2 S_ATA1 S_ATA0

F_USB1 F_USB2

PWR_LED

F_PANEL

SYS_FAN

Block Diagram

LGA775 Processor CPUCLK+/-(200/133MHz)

PCI-ECLK (100MHz)

Host Interface PCI Express x16 Intel 915P GMCH

Instances of Non-Warranty
1. 2. 3. 4. 5. 6. Damage due to natural disaster, accident or human cause. Damage as a result of violating the conditions recommended in the user manual. Damage due to improper installation. Damage due to use of uncertified components. Damage due to use exceeding the permitted parameters. Product determined to be an unofficial Gigabyte product.

-9Hardware Installation

Feature Summary
Supports the latest Intel Pentium 4 LGA775 CPU Supports 800/533MHz FSB L2 cache varies with CPU Northbridge: Intel 915P Express chipset Southbridge: Intel ICHDDR DIMM memory slots (supports up to 4GB memory) (Note 1) Supports dual channel DDR400/333 DIMM Supports 2.5V DDR DIMM 1 PCI Express x 16 slot 1 PCI Express x 1 slot 2 PCI slots 1 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of 2 IIDE devices 1 FDD connection, allows connection of 2 FDD devices 4 Serial ATA connections 1 parallel port supporting Normal/EPP/ECP mode 1 COMA port, onboard COMB connection 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable) 3 IEEE1394 ports (requires cable) 1 front audio connector 1 IR connector 1 PS/2 keyboard port 1 PS/2 mouse port Onboard Realtek 8110S chip (10/100/1000 Mbit) 1 RJ 45 port ALC880 CODEC High Definition Audio Supports 2 / 4 / 6 / 8 channel audio Supports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out (Rear Speaker Out) ; Center/Subwoofer Speaker Out ;Side Speaker Out connection Supports SPDIF In/Out connection CD In IT8712

Chipset Memory

IDE Connections FDD Connections Onboard SATA Peripherals
Onboard LAN Onboard Audio

I/O Control

(Note 1) Due to standard PC architecture, a certain amount of memory is reserved for system usage and therefore the actual memory size is less than the stated amount. For example, 4 GB of memory size will instead be shown as 3.xxGB memory during system startup.

GA-8I915P-MF Motherboard

- 10 -

Hardware Monitor

BIOS Additional Features Overclocking Form Factor
System voltage detection CPU temperature detection CPU / System fan speed detection CPU warning temperature CPU / System fan failure warning CPU smart fan control Use of licensed AWARD BIOS Supports Q-Flash Supports @BIOS Supports EasyTune5 (only supports Hardware Monitor function) Over Clock via BIOS (DDR) Micro ATX form factor; 24.4 cm x 24.4cm

- 11 -

Hardware Installation
Installation of the CPU and Heatsink
Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and heatsink. 4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur. 5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. HT functionality requirement content : Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components: - CPU: An Intel Pentium 4 Processor with HT Technology - Chipset: An Intel Chipset that supports HT Technology - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology

- 13 -

Installation of Memory
Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage. 3. Memory modules have a foolproof insertion design. A memory module can be installed in only one direction. If you are unable to insert the module, please switch the direction.
The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory capacity and specifications. Memory modules are designed so that they can be inserted only in one direction. The memory capacity used can differ with each slot.
The DIMM slot has a notch, so the DIMM memory module can only fit in one direction.
Insert the DIMM memory module vertically into the DIMM slot. Then push it down.
Close the plastic clip at both edges of the DIMM slots to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module.

- 14 -

GA-8I915P-MF supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will add double up to 6.4GB/s. GA-8I915P-MF includes 4 DIMM sockets, and each Channel has two DIMM sockets as following: Channel A : DDR 1, DDR 2 Channel B : DDR 3, DDR 4 If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications. 1. Only one DDR memory module is installed: The Dual Channel Technology can't operate when only one DDR memory module is installed. 2. Two DDR memory modules are installed (the same memory size and type): The Dual Channel Technology will operate when two memory modules are inserted individually into Channel A and B. If you install two memory modules in the same channel, the Dual Channel Technology will not operate. 3. Three DDR memory modules are installed: Please note that The Dual Channel Technology will not operate when three DDR memory modules are installed; part of them will not be detected. 4. Four DDR memory modules are installed: If you install four memory modules at the same time, the Dual Channel Technology will operate only when those modules have the same memory size and type. We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in order for Dual Channel Technology to work. The following tables include all memory-installed combination types: Figure 1: Dual Channel Technology (DS: Double Side, SS: Single Side)

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>.

- 29 -

BIOS Setup
The Main Menu (For example: BIOS Ver. : F4)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M.I.T.) ESC: Quit F8: Q-Flash : Select Item F10: Save & Exit Setup Time, Date, Hard Disk Type. Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden. Please Load Optimized Defaults in the BIOS when somehow the system works not stable as usual. This action makes the system reset to the default for stability.

Standard CMOS Features

This setup page includes all the items in standard compatible BIOS.

Advanced BIOS Features

This setup page includes all the items of Award special enhanced features.

Integrated Peripherals

This setup page includes all onboard peripherals.

Power Management Setup

This setup page includes all the items of Green function features.

PnP/PCI Configuration

This setup page includes all the configurations of PCI & PnP ISA resources.

PC Health Status

This setup page is the System auto detect Temperature, voltage, fan, speed.
MB Intelligent Tweaker(M.I.T.)

This setup page is control CPU clock and frequency ratio.

Load Fail-Safe Defaults

Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe configuration.

Load Optimized Defaults

Optimized Defaults indicates the value of the system parameters which the system would be in best performance configuration.

Set Supervisor Password

Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.

- 30 -

Set User Password
Change, set, or disable password. It allows you to limit access to the system.

Save & Exit Setup

Save CMOS value settings to CMOS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.

- 31 -

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) IDE Channel 0 Master IDE Channel 0 Slave Drive A Drive B Floppy 3 Mode Suport Holt On Base Memory Extended Memory Total Memory Thu, Apr 22:31:24 [None] [None] [1.44M, 3.5"] [None] [Disabled] [All, But Keyboard] 640K 127M 128M Item Help Menu Level Change the day, month, year <Week> Sun. to Sat. <Month> Jan. to Dec. <Day> 1 to 31 (or maximum allowed in the month) <Year> 1999 to 2098 : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6: Fail-Save Default F10: Save ESC: Exit F1: General Help F7: Optimized Defaults
The date format is <week>, <month>, <day>, <year>. Week The week, from Sun to Sat, determined by the BIOS and is display only Month The month, Jan. Through Dec. Day The day, from 1 to 31 (or the maximum allowed in the month) Year The year, from 1999 through 2098
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.
IDE Channel 0 Master, Slave
IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. IDE Channel 0 Master(Slave) IDE Device Setup. You can use one of three methods: Auto Allows BIOS to automatically detect IDE devices during POST(default) None Select this if no IDE devices are used and the system will skip the automatic detection step and allow for faster system start up. Manual User can manually input the correct settings Access Mode Use this to set the access mode for the hard drive. The four options are: CHS/LBA/Large/Auto(default:Auto) Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information. Cylinder Number of cylinders Head Number of heads Precomp Write precomp Landing Zone Landing zone Sector Number of sectors If a hard disk has not been installed, select NONE and press <Enter>. GA-8I915P-MF Motherboard - 32 -

Drive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity. 1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is Enabled). 720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity 1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity. 2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled Drive A Drive B Both Normal Floppy Drive. (Default value) Drive A is 3 mode Floppy Drive. Drive B is 3 mode Floppy Drive. Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power up. No Errors The system boot will not stop for any error that may be detected and you will be prompted. All Errors Whenever the BIOS detects a non-fatal error the system will be stopped. All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value) All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K memory installed on the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map.

- 33 -

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features [Press Enter] [Floppy] [Hard Disk] [CDROM] [Setup] [Enabled] [Enabled] [Disabled] [Disabled] [Disabled] Item Help Menu Level Select Hard Disk Boot Device Priority
Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check # CPU Hyper-Threading Limit CPUID Max. to 3 No-Execute Memory Protect (Note) CPU Enhanced Halt (C1E) (Note) CPU Thermal Monitor 2(TM2) (Note)

USB Mouse Support

Enabled Disabled

Azalia Codec

Auto Disabled

Front Panel Type

If you connect HD Audio Panel to the AZALIA_FP connector, set this item to HD Audio. If you connect AC97 Audio Panel to the AZALIA_FP connector, set this item to AC97. AC97 Set front audio panel type to AC97. HD Audio Set front audio panel type to HD Audio. (Default value)

- 37 -

Onboard H/W 1394
Enabled Disabled Enable onboard IEEE 1394 function.(Default value) Disable this function. Enable Onboard H/W LAN1 function. (Default value) Disable this function.

Onboard H/W LAN1

Onboard LAN Boot ROM
This function decide whether to invoke the boot ROM of the onboard LAN chip. Enabled Enable this function. Disabled Disable this function. (Default value)

Onboard Serial Port 1

Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled BIOS will automatically setup the port 1 address. Enable onboard Serial port 1 and address is 3F8. (Default value) Enable onboard Serial port 1 and address is 2F8. Enable onboard Serial port 1 and address is 3E8. Enable onboard Serial port 1 and address is 2E8. Disable onboard Serial port 1. BIOS will automatically setup the port 2 address. Enable onboard Serial port 2 and address is 3F8. Enable onboard Serial port 2 and address is 2F8. (Default value) Enable onboard Serial port 2 and address is 3E8. Enable onboard Serial port 2 and address is 2E8. Disable onboard Serial port 2.

Onboard Serial Port 2

UART Mode Select
This item allows you to determine which Infra Red(IR) function of Onboard I/O chip. Normal Set onboard I/O chip UART to Normal Mode. (Default Value) ASKIR Set onboard I/O chip UART to ASKIR Mode. IrDA Set onboard I/O chip UART to IrDA Mode.

UR2 Duplex Mode

This feature allows you to seclect IR mode. This function will available when "UART Mode Select" doesn't set at Normal. Half IR Function Duplex Half. (Default value) Full IR Function Duplex Full.

Onboard Parallel port

Disabled 378/IRQ7 278/IRQ5 3BC/IRQ7 Disable onboard LPT port. Enable onboard LPT port and address is 378/IRQ7. (Default value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7.

- 38 -

Parallel Port Mode
SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. (Default value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as ECP & EPP mode. Set ECP Mode Use DMA to 3. (Default value) Set ECP Mode Use DMA to 1.

Auto 3,4,5,7,9,10,11,12,14,15 Auto assign IRQ to PCI 1. (Default value) Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1. Auto assign IRQ to PCI 2. (Default value) Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.

PCI 2 IRQ Assignment

Auto 3,4,5,7,9,10,11,12,14,15

- 41 -

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software PC Health Status Vcore DDR25V +3.3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning CPU Smart FAN Control CPU FAN PIN Type OK OK OK OK 33 oC 4687 RPM 0 RPM [Disabled] [Disabled] [Disabled] [Enabled] [3 PIN] Item Help Menu Level
Current Voltage(V) Vcore / DDR25V / +3.3V / +12V
Detect system's voltage status automatically.

Current CPU Temperature

Detect CPU temperature automatically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM Fan speed status automatically.

CPU Warning Temperature

60o C / 140oF 70o C / 158oF 80o C / 176oF 90o C / 194oF Disabled Disabled Enabled Disabled Enabled Monitor CPU temperature at 60oC / 140 oF. Monitor CPU temperature at 70oC / 158 oF. Monitor CPU temperature at 80oC / 176 oF. Monitor CPU temperature at 90oC / 194 oF. Disable this function. (Default value) Fan warning function disable. (Default value) Fan warning function enable. Disable this function. Enable CPU Smart Fan control function. (Default value) a. When the CPU temperature is higher than 65 degrees Celsius, CPU fan will operate at full speed. b. When the CPU temperature is between 20 and 65 degrees Celsius, the CPU fan speed will change depending on the actual CPU temperature. c. When the CPU temperature is lower than 20 degrees Celsius, CPU fan will stop spinning.
CPU/SYSEM FAN Fail Warning

CPU Smart FAN Control

- 42 -

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled. Auto BIOS autodetects the type of CPU fan you installed and sets the optimal CPU Smart FAN control mode for it. (Default value) Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable. PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable. In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables. However, some 4-pin CPU fan power cables are not designed following Intel 4-wire fans PWM control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan speed.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software MB Intelligent Tweaker(M.I.T.) CPU Clock Ratio Memory Frequency For Memory Frequency (Mhz) [15X] [Auto] 400 Item Help Menu Level

5. Exit and Restart:

Exit and restart your computer.

- 55 -

4-1-3 Flash BIOS Method Introduction
Method 1 : Q-FlashTM Utility
Q-Flash TM is a BIOS flash utility embedded in Flash ROM. With this utility, users only have to stay in the BIOS menu when they want to update BIOS. Q-Flash TM allows users to flash BIOS without any utility in TM DOS or Windows. Using Q-Flash indicating no more fooling around with any complicated instructions and operating system since it is in the BIOS menu. Please note that because updating BIOS has potential risk, please do it with caution!! We are sorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because of incorrect manipulation of updating BIOS to avoid any claims from end-users.

Before You Begin:

Before you start updating BIOS with the Q-Flash TM utility, please follow the steps below first. 1. 2. 3. Download the latest BIOS for your motherboard from Gigabyte's website. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For example, 8KNXPU.Fba) to a floppy disk. Reboot your PC and press Del to enter BIOS menu.
The BIOS upgrading guides below are separated into two parts. If your motherboard has dual-BIOS, please refer to Part One. If your motherboard has single-BIOS, please refer to Part Two.
Part One: Updating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards.
Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards supporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the same screen. This section only deals with how to use Q-Flash utility. In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOS from an older version to the latest version. For example, from Fa3 to Fba.
Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-2003, Award Software, Inc.
The BIOS file is Fa3 before updating
Intel i875P AGPset BIOS for 8KNXP Ultra Fa3 Check System Health OK , VCore = 1.5250 Main Processor : Intel Pentium(R) 4 1.6GHz (133x12) <CPUID : 0F27 Patch ID : 0027> Memory Testing : 131072K OK Memory Frequency 266 MHz in Single Channel Primary Master : FUJITSU MPE3170AT ED-03-08 Primary Slave : None Secondary Master : CREATIVEDVD-RM DVD1242E BC101 Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For Xpress Recovery 08/07/2003-i875P-6A79BG03C-00

- 56 -

Entering the Q-FlashTM utility:
Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M.I.T.) ESC: Quit F8: Dual BIOS/Q-Flash Select Language Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language F10: Save & Exit Setup Time, Date, Hard Disk Type.

Wide Range Protection Disable 1 file(s) found Boot From Main Bios 8KNXPU.Fba 512K Auto Recovery Enable Halt On Error Disable Total size Copy Main ROM Data to Backup : 1.39M Free size : 911.50K F5 : Refresh DEL : Load Default SettingsDelete Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run :Move ESC:Reset F10:Power Off
BIOS file in the floppy disk.
After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.
Dual BIOS Utility Boot From... Main Bios Main ROM Type/Size..SST 49LF003A Backup ROM Type/Size..SST 49LF003A Wide Range Protection Disable Boot From Main Bios Reading BIOS file from floppy. Auto Recovery Enable >>>>>>>>>>>>>>. Halt On Error Disable Copy Main ROM Data to Backup Don't Turn Off Power or Reset System Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy :Move ESC:Reset F10:Power Off
Do not trun off power or reset your system at this stage!!

Enter : Run

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?" GA-8I915P-MF Motherboard - 58 -
3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be displayed. Please do not take out the floppy disk when it begins flashing BIOS. 4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Wide Range Protection Disable Boot From Main Bios Auto Recovery Enable !! Copy BIOS completed - Pass !! Halt On Error Disable Copy Main ROM Data to continue Please press any key to Backup Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run :Move ESC:Reset F10:Power Off
You can repeat Step 1 to 4 to flash the backup BIOS, too.
Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after you exit Q-Flash.

Do not trun off power or reset your system at

this stage!!

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?" Please do not take out the floppy disk when it begins flashing BIOS. - 61 Appendix
Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time.
Keep DMI Data BIOS Now Updating Enable Update BIOS from Floppy >>>>>>>>>>>>>>>>>>>.. Save BIOS to Floppy Enter : Run :Move ESC:Reset F10:Power Off Don't Turn Off Power or Reset System
Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Keep DMI Data Enable !! Copy BIOS completed - Pass !! Update BIOS from Floppy Save BIOS to Floppy Please press any key to continue :Move ESC:Reset F10:Power Off
Keep DMI Data Enable Are you sure to RESET ? Update BIOS from Floppy Save BIOS to Floppy [Enter] to continure or [Esc] to abort. Enter : Run :Move ESC:Reset F10:Power Off
The BIOS file becomes F4 after updating
Intel 845GE AGPSet BIOS for 8GE800 F4 Check System Health OK Main Processor : Intel Pentium(R) 4 1.7GHz (100x17.0) <CPUID : 0F0A Patch ID : 0009> Memory Testing : 122880K OK + 8192K Shared Memory Primary Master : FUJITSU MPE3170AT ED-03-08 Primary Slave : None Secondary Master : CREATIVEDVD-RM DVD1242E BC101 Secondary Slave : None
Press DEL to enter SETUP / Q-Flash 03/18/2003-I845GE-6A69YG01C-00
Press Del to enter BIOS menu after system reboots and "Load BIOS Fail-Safe Defaults". See how to Load BIOS Fail-Safe Defaults, please kindly refer to Step 6 to 7 in Part One.
Congratulation!! You have updated BIOS successfully!!

- 62 -

Method 2 : @BIOSTM Utility
If you do not have a DOS startup disk, we recommend that you use the new @BIOS utility. @BIOS allows users to update their BIOS under Windows. Just select the desired @BIOS server to download the latest version of BIOS. Fig 1. Installing the @BIOS utility Fig 2. Installation Complete and Run @BIOS
Click Sart/ Programs/ GIGABYTE/@BIOS
Select @BIOS item than click Install

Stereo Speakers Connection and Settings:
We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo output is applied.
STEP 1: Connect the stereo speakers or earphone to "Line Out". Line Out
STEP 2 : Following installation of the audio driver, you find a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function.

- 65 -

STEP 3: Click "Speaker Configuration" then click on the left selection bar and select "2CH Speaker" to complete 2 channel audio configuration.

4 Channel Audio Setup

STEP 1 : Connect the front channels to "Front Speaker Out", the rear channels to "Rear Speaker Out".

Front Speaker Out

STEP 3: Click "Speaker Configuration" then click on the left selection bar and select "4CH Speaker" to complete 4 channel audio configuration.

- 66 -

6 Channel Audio Setup
STEP 1 : Connect the front channels to "Front Speaker Out", the rear channels to "Rear Speaker Out", and the Center/Subwoofer channels to "Center/Subwoofer Speaker Out".
Front Speaker Out Rear Speaker Out Center/Subwoofer Speaker Out
STEP 3: Click "Speaker Configuration" then click on the left selection bar and select "6CH Speaker" to complete 6 channel audio configuration.

- 67 -

8 Channel Audio Setup
STEP 1 : Connect the front channels to "Front Speaker Out", the rear channels to "Rear Speaker Out", the Center/ Subwoofer channels to "Center/Subwoofer Speaker Out", and the side channels to "Side Speaker Out".
Front Speaker Out Rear Speaker Out Center/Subwoofer Speaker Out Side Speaker Out
STEP 3: Click "Speaker Configuration" then click on the left selection bar and select "8CH Speaker" to complete 8 channel audio configuration.
Sound Effect Configuration: At the sound effect menu, users can adjust sound option settings as desired.

AWARD BIOS Beep Codes 1 short: System boots successfully 2 short: CMOS setting error 1 long 1 short: DRAM or M/B error 1 long 2 short: Monitor or display card error 1 long 3 short: Keyboard error 1 long 9 short: BIOS ROM error Continuous long beeps: DRAM error Continuous short beeps: Power error

- 70 -

- 71 -

- 72 -

- 73 -

- 74 -

- 75 -

- 76 -

- 77 -

- 78 -

Taiwan (Headquarters) GIGA-BYTE TECHNOLOGY CO., LTD. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan. TEL: +886 (2) 8912-4888 FAX: +886 (2) 8912-4003 Tech. Support : http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address (English): http://www.gigabyte.com.tw WEB address (Chinese): http://chinese.giga-byte.com U.S.A. G.B.T. INC. Address: 17358 Railroad St, City of Industry, CA 91748. TEL: +1 (626) 854-9338 FAX: +1 (626) 854-9339 Tech. Support : http://www.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.giga-byte.com Germany G.B.T. TECHNOLOGY TRADING GMBH Address: Friedrich-Ebert-Damm Hamburg TEL: +49-40-2533040 (Sales) +49-1803-428468 (Tech.) TEL: +49-40-25492343 (Sales) +49-1803-428329 (Tech.) Tech. Support : http://de.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.gigabyte.de Japan NIPPON GIGA-BYTE CORPORATION WEB address : http://www.gigabyte.co.jp Singapore GIGA-BYTE SINGAPORE PTE. LTD. Tech. Support : http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp U.K. G.B.T. TECH. CO., LTD. Tech. Support : http://uk.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://uk.giga-byte.com The Netherlands GIGA-BYTE TECHNOLOGY B.V. TEL: +NL Tech.Support : 0900-GIGABYTE (0900-44422983) BE Tech.Support : 0900-84034 FAX: +Tech. Support : http://nz.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.giga-byte.nl

- 79 -

China NINGBO G.B.T. TECH. TRADING CO., LTD. Tech. Support : http://cn.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.gigabyte.com.cn Shanghai TEL: +86-021-63410999 FAX: +86-021-63410100 Beijing TEL: +86-010-82886651 FAX: +86-010-82888013 Wuhan TEL: +86-027-87851061 FAX: +86-027-87851330 GuangZhou TEL: +86-020-87586074 FAX: +86-020-85517843 Chengdu TEL: +86-028-85236930 FAX: +86-028-85256822 Xian TEL: +86-029-85531943 FAX: +86-029-85539821 Shenyang TEL: +86-024-23960918 FAX: +86-024-23960918-809

GA-8I915P-MF

Intel Pentium 4 LGA775

2002 12MR-8I915PMF-2002

Motherboard GA-8I915P-MF

Jun. 11, 2004
2004 GIGA-BYTE TECHNOLOGY CO., LTD. . , , -.
, , Gigabyte. , , - - Gigabyte. .
, Gigabyte . ! Gigabyte , Web- Gigabyte, "Technology Guide" .pdf. Web- Gigabyte: www.gigabyte.com.tw.
GA-8I915P-MF.. 6 -.... ... 9
1-1 1-2 1-3 ... 9 ... 10 .. 12
1-3-1 1-3-2 ... 12 .. 13

1-4 1-5 1-6 1-7

... 14 ... 16 ... 17 .. 18

BIOS.... 29

( BIOS F1).. 30 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 Standard CMOS Features ( BIOS).. 32 Advanced BIOS Features ( BIOS).. 34 Integrated Peripherals ( ).... 36 Power Management Setup ( ). 39 PnP/PCI Configurations ( PnP/PCI). 41 PC Health Status ( ).. 42 MB Intelligent Tweaker (M.I.T.) ( MIT).. 43 Load Fail-Safe Defaults ( )... 44 Load Optimized Defaults ( )... 44 Set Supervisor/User Password ( / )... 45 Save & Exit Setup ( ).. 46 Exit Without Saving ( ).. 46

... 47

3-1 3-2 3-3 3-4 3-5 ... 47 .. 48 , -.. 48 .. 49 ... 49

... 51

4-1 Gigabyte.. 51
4-1-1 4-1-2 4-1-3 Xpress Recovery... 52 BIOS... 55 2- / 4- / 6- / 8- .. 64

... 69

GA-8I915P-MF

KB_MS SPDIF_O SPDIF_I

CPU_FAN

IT8712

LGA775 R_USB ATX_12V

USB LAN

Intel 915P

AZALIA_FP

AUDIO1 AUDIO2

PCIE_16

DDR1 DDR2 DDR3 DDR4
PCI1 RTL8110S PCI2 TSB43AB23 CD_IN PCIE_1 COMB F2_1394 F1_1394

CLR_CMOS

S_ATA3 S_ATA2 S_ATA1 S_ATA0

F_USB1 F_USB2

PWR_LED

F_PANEL

SYS_FAN
Pentium 4 LGA775 PCI Express x16 Intel 915P GMCH CPUCLK+/-(200/133 )

PCI-ECLK (100 )

DDR DIMM 400/333 GMCHCLK (133/200 ) 14.BIOS
1 PCIExpress x 1 PCI-ECLK (100 ) PCI Express x1 PCI TSB43AB23 RTL 8110S

3 IEEE1394

4 Serial ATA Intel ICH6 IDE ATA33/66/100 IT 8712 LPT-

COM- 8 USB / PS/2

PCICLK (33 )
Center/Subwoofer Speaker Out Surround Speaker Out Side Speaker Out MIC Line-Out Line-In SPDIF In SPDIF Out
. : 1. . 2. . 3. (, ) . 4. . 5. , .
1. , . 2. . 3. , . 4. , . 5. , . 6. . 7. , , . 8. - .
1. c , . 2. , , . 3. , . 4. , . 5. . 6. , Gigabyte.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Intel Pentium 4 LGA775 800/533 - 2 : Intel 915P Express : Intel ICHDDR DIMM ( 4 ) (. 1) DDR DIMM 400/333 2.5 DDR DIMM 1 PCI Express x PCI Express x PCI 1 IDE (UDMA 33/ATA 66/ATA 100), 2 IDE 1 - 2 - 4 Serial ATA 1 Normal/EPP/ECP 1 (COMA), COMB 8 USB 2.0/1.1 (4 , 4 - , ) 3 IEEE1394 ( ) 1 1 - 1 PS/2 1 PS/2 Realtek 8110S (10/100/1000 /) 1 RJ45 ALC880 Jack Sensing 2- /4- /6- /8 - Line In; Line Out (Front Speaker Out); MIC; Surround Speaker Out (Rear Speaker Out); Center/Subwoofer Speaker Out; Side Speaker Out SPDIF In / Out CD In

IDE - Serial ATA

! ! ! ! ! ! ! ! ! ! ! ! !
(. 1) - , - . , 4 3.xx. GA-8I915P-MF - 10 -
! IT8712 ! AWARD BIOS ! Q-Flash ! @BIOS ! ! ! ! ! ! ! BIOS ! Micro ATX, 24.4 x 24.4

BIOS -

- 11 -
: 1. , . 2. . , . . 3. . 4. . . 5. . c , . : , , , . HT: Hyper-Threading : - Intel Pentium 4 HT - Intel , HT - BIOS, HT ( HT ) - , HT
. 1 . 2 , . 4 , , , .
. 3 . . ( . , .) GA-8I915P-MF - 12 -

.1 .
. 2 , , - . , . ( Intel, Intel.)

. 3 . , . , , .

. 4 , . , .

. 5 . , , .

. 6 CPU_FAN . .

- . , . - 13

: 1. , . , . 2. , . . 3. . , .

DDR. BIOS. . .

, .

. , .

. .

GA-8I915P-MF

- 14 -
GA-8I915P-MF . - 6,4 /. GA-8I915P-MF 4 DIMM. 2 , : A : DDR 1, DDR 2 B : DDR 3, DDR 4 , , Intel: 1. DDR. . 2. DDR ( ). , , - . DDR , . 3. DDR. . . 4. DDR. , . . . ". 1: (DS: DIMM, SS: DIMM)
DDR 4 DS/SS X DS/SS DDR 2 X DS/SS DS/SS DDR 3 DS/SS X DS/SS DDR 4 X DS/SS DS/SS
". 2: (DS: DIMM, SS: DIMM)
DDR DS/SS X X X 2 3 DS/SS X DS/SS DS/SS DS/SS X DDR 2 X DS/SS X X DS/SS X DS/SS DS/SS X DS/SS DDR 3 X X DS/SS X X DS/SS DS/SS X DS/SS DS/SS DDR 4 X X X DS/SS X DS/SS X DS/SS DS/SS DS/SS

- 15 -

: 1. . 2. , . 3. . 4. , . 5. . 6. . 7. . BIOS. 8. . PCI Express x 16 :
PCI Express x 16 . PCI Express x 16 , , .

- 16 -

PS/2 PS/2

() PS/2, - () PS/2.

, .

SPDIF_O ( SPDIF)

SPDIF AC3 Dolby Digital.

SPDIF_I ( SPDIF)

SPDIF In , .

COM A ( )

.
(, , , ZIP-, .) USB , USB-. , USB. USB, , . .
10/100/1000 / (Gigabit Ethernet).

, , CD-ROM .

, .

. - 17

. 2- /4- /6- /8- .
1) 2) 3) 4) 5) 6) 7) 8) 9)
ATX_12V ATX ( ) CPU_FAN SYS_FAN FDD IDE S_ATA0 / S_ATA1 / S_ATA2 / S_ATA3 F_PANEL PWR_LED
10) 11) 12) 13) 14) 15) 16) 17)
AZALIA_FP CD_IN F_USB1 / F_USB2 F1_1394 / F2_1394 IR COMB CLR_CMOS BAT

- 18 -

ATX_12V/ATX ( )
. , . , . . ATX_12V . ATX_12V , . ! . 300 . , . ATX 24- ; .

11 12

GND GND +12V +12V 3.3V 3.3V GND VCC GND VCC GND Power Good 5V SB (. +5 ) +12V +12V 3.3V ( 24 ATX) 3.3V -12V GND PS_ON (.) GND GND GND -5V VCC VCC VCC GND

- 19 -

CPU_FAN / SYS_FAN ( )
- ( CPU_FAN) +12. . . , +12. (GND). ! . ! ! .
GND +12V Sense ( CPU_FAN)

5) FDD ( -)

-. - 360 , 720 , 1.2 , 1.44 2.88. 1-.

- 20 -

6) IDE ( IDE)
IDE-. IDE, IDE- ( ). IDE- Master, - Slave ( IDE-).
7) S_ATA0/S_ATA1/S_ATA2/S_ATA3 ( Serial ATA, ICH6)
Serial ATA ( 150 /). BIOS .
GND TXP TXN GND RXN RXP GND

- 21 -

F_PANEL ( )

, , , / F_PANEL .

/ /

SPEAK+

SPEAK-

NC RES+ RESHDHD+

PWPW+ MSGMSG+

HD ( ) SPEAK ( )

1: (+) 2: (-) 1: VCC (+) 2- 3: 4: (-)
RES ( ) PW ( ) MSG ( //) NC
: : : :./. 1: (+) 2: (-)

- 22 -

9) PWR_LED ( )
PWR_LED , , . (Suspend), .

MPD+ MPDMPD-

10) AZALIA_FP ( )

. , .

MIC2_L GND MIC2_R -ACZ_DET Line2_R FSENSE1 FAUOIO_JD LINE2_L FSENSE2

- 23 -

11) CD_IN ( CD-ROM)

CD-ROM DVD-ROM.

CD-L GND GND CD-R
12) F_ USB1 / F_USB2 ( USB )
USB . . USB . S3 USB- ("USB Device Wake up From S3") USB .
Power Power USB DXUSB DyUSB DX+ USB Dy+ GND GND

- 24 -

13) F1_1394/F2_1394 ( IEEE 1394)
IEEE1394 - , , . IEEE1394 . . IEEE1394 .

F2_1394

15 16
Power Power TPA0+ TPA0GND GND TPB0+ TPB0Power Power TPA1+ TPA1GND TPB1+ TPB1-

F1_1394

TPA2+ TPA2GND GND TPB2+ TPB2 Power Power GND

14) IR

. .

VCC IR RX GND IR TX

- 25 -

15) COMB ( )

. . .
NDCD BNSIN B NSOUT B NDTR BGND NDSR BNRTS BNCTS BNRI B

16) CLR_CMOS ( CMOS)

CMOS, . CMOS 1-2 . .

1 : CMOS

- 26 -

17) BAT ()

# . # , . # . CMOS: 1. . 2. 30. 3. . 4. .

- 27 -

- 28 -
BIOS ( -) CMOS SETUP, BIOS , . CMOS SETUP CMOS . CMOS ; , . BIOS, (POST) <Del>. BIOS, "Ctrl + F1". BIOS BIOS , . BIOS, Q-Flash @BIOS Gigabyte. Q-Flash - BIOS BIOS . @BIOS - BIOS Windows, DOS. BIOS .
< >< >< <Enter> <Esc> >< > - CMOS. - ( ) CMOS ( ) BIOS BIOS Q-Flash CMOS ( )
<Page Up> <Page Down> <F1> <F2> <F5> <F6> <F7> <F8> <F9> <F10>
F1 . <Esc>. ( BIOS E4) - 29 BIOS

( BIOS F1)

BIOS (Award BIOS CMOS Setup Utility) (.). . <Enter>.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M.I.T.) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving "#$%: Select Item F10: Save & Exit Setup Time, Date, Hard Disk Type.

ESC: Quit F8: Q-Flash

, "Ctrl+F1" BIOS. , , BIOS Load Optimized Defaults. .
! Standard CMOS Features ( BIOS)

BIOS.

! Advanced BIOS Features ( BIOS)

Award BIOS.

! Integrated Peripherals ( )
! Power Management Setup ( )
! PnP/PCI Configurations ( PnP PCI)

PCI PnP ISA.

! PC Health Status ( )
! MB Intelligent Tweaker (M.I.T.) ( MIT)

.

! Load Fail-Safe Defaults ( )
! Load Optimized Defaults ( )

. GA-8I915P-MF - 30 -

! Set Supervisor password ( )

, . BIOS BIOS.

! Set User password ( )

, , .

! Save & Exit Setup ( )

CMOS .

! Exit Without Saving ( )

- 31 -

Standard CMOS Features ( BIOS)
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Thu, Apr 22:31:24 [None] [None] [1.44M, 3.5"] [None] [Disabled] [All, But Keyboard] 640K 127M 128M Item Help Menu Level! Change the day, month, year <Week> Sun. to Sat. <Month> Jan. to Dec. <Day> 1 to 31 (or maximum allowed in the month) <Year> 1999 to 2098
! IDE Channel 0 Master ! IDE Channel 0 Slave Drive A Drive B Floppy 3 Mode Suport Holt On Base Memory Extended Memory Total Memory
"#$%: Move Enter: Select F5: Previous Values
+/-/PU/PD: Value F6: Fail-Save Default

F10: Save

ESC: Exit F1: General Help F7: Optimized Defaults

Date ()

: < >, <>, <>, <>. Week BIOS ; Month , Day , ( ) Year , 1999 2098

Time ()

: <> <> <>. 24- , , 1 13:00:00.
IDE Channel 0 Master, Slave ( IDE-)
IDE HDD Auto-Detection IDE-, , "Enter". IDE Channel 0 Master(Slave) IDE Device Setup : Auto BIOS IDE. ( ) None , IDE. , . Manual IDE- . Access Mode . : CHS/LBA/Large/Auto ( : Auto) . : Cylinder Head Precomp Landing Zone Sector , NONE <Enter>. GA-8I915P-MF - 32 -

Drive A / Drive B (-)

- , . None - 360K, 5.25" 5.25- - PC 360 K 1.2M, 5.25" 5.25- - AT , 1,2 M (3.5- , 3) 720K, 3.5" 3.5- ; 720 K 1.44M, 3.5" 3.5- ; 1.44 M 2.88M, 3.5" 3.5- ; 2.88 M.
Floppy 3 Mode Support (for Japan Area) ( 3 - )
Disabled Drive A Drive B Both -. ( ) - 3. - B 3. - B 3.

Halt on ( )

, . . . All Errors , BIOS . All, But Keyboard , . ( ) All, But Diskette , -. All, But Disk/Key , . NO Errors

Memory ()

, BIOS . .

Base Memory ( )

BIOS ( ) , . 512 K, 512 K, 640 K , 640 K.

Extended Memory ( )

BIOS . - 1 .

- 33 -

Advanced BIOS Features ( BIOS)
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features [Press Enter] [Floppy] [Hard Disk] [CDROM] [Setup] [Enabled] [Enabled] Item Help Menu Level! Select Hard Disk Boot Device Priority

! Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check # CPU Hyper-Threading Limit CPUID Max. to 3
" # " Intel Pentium 4 HT, .
Hard Disk Boot Priority ( )
SCSI, RAID . < > < >, <+> <-> . <ESC>.
First / Second / Third Boot Device (// )
Floppy LS120 Hard Disk CDROM ZIP USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Setup System -. LS120. . CD-ROM. ZIP-. - USB. ZIP- USB. CD-ROM USB. USB. .

Password Check ( )

, , . ( ) , .

- 34 -

CPU Hyper-Threading ( )
Enabled Hyper-Threading. , , . ( ) Hyper-Threading. CPUID 3 , Windows NT4. ( ) CPUID Windows XP.
Disabled Enabled Disabled
Limit CPUID Max. to 3 ( CPUID 3)

- 35 -

Integrated Peripherals ( )
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals [Enabled] [Auto] Ch.1 Master/Slave Ch.2 Master/Slave Ch.3 Master/Slave [Enabled] [Enabled] [Disabled] [Disabled] [Auto] [Enabled] [Enabled] [Disabled] [3F8/IRQ4] [2F8/IRQ3] [Normal] [Half] [378/IRQ7] [SPP] +/-/PU/PD: Value F6: Fail-Save Default F10: Save Item Help Menu Level!
On-Chip Primary PCI IDE On-Chip SATA Mode x PATA IDE Set to SATA Port 0/2 Set to SATA Port 1/3 Set to USB Controller USB 2.0 Controller USB Keyboard Support USB Mouse Support Azalia Codec Onboard H/W 1394 Onboard H/W LAN1 Onboard LAN Boot ROM Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode "#$%: Move Enter: Select F5: Previous Values
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals x ECP Mode Use DMA 3 Item Help Menu Level!
On-Chip Primary PCI IDE ( 1 IDE)
Enabled Disabled Disabled Auto 1 IDE. ( ) 1 IDE.
On-Chip SATA Mode ( Serial ATA)
. BIOS Serial ATA. ( ) Combined 4 : 2 - Serial ATA, - Parallel ATA IDE. Enhanced 6 . Non-Combined Serial ATA Parallel ATA. GA-8I915P-MF - 36 -
PATA IDE Set to ( Parallel ATA)
Ch.1 Master/Slave Ch.0 Master/Slave Parallel ATA IDE Ch. 1 Master/Slave. ( ) Parallel ATA IDE Ch. 0 Master/Slave.
SATA Port 0/2 Set to ( Serial ATA 0/2)
"On-Chip SATA Mode" "PATA IDE Set to". PATA IDE Ch. 1 Master/Slave, Ch. 0 Master/Slave.
SATA Port 1/3 Set to ( Serial ATA 1/3)
"On-Chip SATA Mode" "PATA IDE Set to". PATA IDE Ch. 0 Master/Slave, Ch. 1 Master/Slave.

Power On By Keyboard ( )
KB Power ON Password ( )
"Power On by Keyboard" Password, . Enter ( - ) Enter.

AC Back Function ( )

Soft-Off Full-On Memory . ( ) . , .

- 40 -

PnP/PCI Configurations ( PnP/PCI)
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment [Auto] [Auto] Item Help Menu Level!
PCI1 IRQ Assignment ( PCI 1)
Auto PCI 1. ( ) 3,4,5,7,9,10,11,12,14,15 PCI 1 IRQ 3,4,5,7,9,10,11,12,14,15. PCI 2. ( ) 3,4,5,7,9,10,11,12,14,15 PCI 2 IRQ 3,4,5,7,9,10,11,12,14,15.
PCI2 IRQ Assignment ( PCI 2)

- 41 -

PC Health Status ( )
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software PC Health Status Vcore DDR25V +3.3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning CPU Smart FAN Control CPU FAN PIN Type OK OK OK OK 33oC 4687 RPM 0 RPM [Disabled] [Disabled] [Disabled] [Enabled] [3 PIN] Item Help Menu Level!
Current Voltage(V) Vcore / DDR25V / +3.3V / +12V ( )
Current CPU Temperature ( )
Current CPU/SYSTEM FAN Speed (RPM) ( )

.

CPU Warning Temperature ( )
60oC / 140oF 70oC / 158oF 80oC / 176oF 90oC / 194oF Disabled 60 oC. 70 oC 80 oC. 90 oC. . ( )
CPU/SYSEM FAN Fail Warning ( )
Disabled Enabled . ( ) .
CPU Smart FAN Control ( )
Disabled Enabled . . ( ) a. 65 . - 42 -

41 - 65, . 40 , .

CPU FAN PIN Type ( )
, . 3 PIN . ( ) 4 PIN .
MB Intelligent Tweaker (M.I.T.) ( MIT)
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software MB Intelligent Tweaker(M.I.T.) CPU Clock Ratio Memory Frequency For Memory Frequency (Mhz) [15X] [Auto] 400 Item Help Menu Level!

! !

CPU Clock Ratio ( )

. , .

Memory Frequency For ( )
. CMOS. 800 : 2.0 = X 2.0. 2.66 = X 2.66. Auto SPD . ( )
Memory Frequency (Mhz) ( ())
, "Memory Frequency For". - 43 BIOS
Load Fail-Safe Defaults ( )
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password Load Fail-Safe DefaultsSave & Exit Setup (Y/N)? N PnP/PCI Configurations PC Health Status Exit Without Saving MB Intelligent Tweaker(M.I.T.) "#$%: Select Item F10: Save & Exit Setup Load Fail-Safe Defaults

- , , .

Load Optimized Defaults ( )
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password Load Optimized Defaults (Y/N)? N Setup PnP/PCI Configurations Save & Exit PC Health Status Exit Without Saving MB Intelligent Tweaker(M.I.T.) "#$%: Select Item F10: Save & Exit Setup Load Optimized Defaults

BIOS , .

- 44 -
Set Supervisor/User Password ( / )
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status MB Intelligent Tweaker(M.I.T.) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving "#$%: Select Item F10: Save & Exit Setup Change/Set/Disable Password
. 8 <Enter>. . <Enter>. , <Esc>. , <Enter>. , , PASSWORD DISABLED. BIOS. BIOS : (SUPERVISOR PASSWORD) (USER PASSWORD). , BIOS. BIOS , - . BIOS "Password Check" System, BIOS. BIOS "Password Check" Setup, BIOS.

- 45 -

! ! ! ! ! ! !
Save & Exit Setup ( )
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup Save to CMOS and EXIT (Y/N)? Y Saving PC Health Status Exit Without MB Intelligent Tweaker(M.I.T.) "#$%: Select Item F10: Save & Exit Setup Save & Exit Setup
"Y". "N".

Exit Without Saving ( )

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M.I.T.) Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Quit Without Saving (Y/N)? NExit Setup Save & Exit Without Saving "#$%: Select Item F10: Save & Exit Setup Abandon all Data
BIOS "Y". BIOS "N".

- 46 -

Windows XP. - CD-ROM. . , - Run.exe.
- Xpress Install , . , , "Install". "Xpress Install".
. Xpress Install . , . . USB 2.0 Windows XP Windows Service Pack. Windows Service Pack "Device Manager" ( ) "Universal Serial Bus controller" ( ) "?". . USB 2.0. - 47

- 54 -

1 : Q-FlashTM
Q-Flash - BIOS BIOS. Q-Flash BIOS DOS Windows. BIOS - BIOS. BIOS , . Gigabyte Technology - .
BIOS Q-Flash, : 1. Web- Gigabyte BIOS . 2. BIOS < >.Fxx (, 8KNXPU.Fba). 3. . Del BIOS. BIOS . Dual BIOS, 1. BIOS, 2.
1: BIOS Q-Flash Dual BIOS
Gigabyte Dual BIOS. BIOS , Q-Flash, Dual BIOS, . Q-Flash. GA-8KNXP Ultra, BIOS Fa3 Fba.
Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-2003, Award Software, Inc. Intel i875P AGPset BIOS for 8KNXP Ultra Fa3 Check System Health OK , VCore = 1.5250 Main Processor : Intel Pentium(R) 4 1.6GHz (133x12) <CPUID : 0F27 Patch ID : 0027> Memory Testing : 131072K OK Memory Frequency 266 MHz in Single Channel Primary Master : FUJITSU MPE3170AT ED-03-08 Primary Slave : None Secondary Master : CREATIVEDVD-RM DVD1242E BC101 Secondary Slave : None

BIOS Fa3

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For Xpress Recovery 08/07/2003-i875P-6A79BG03C-00

- 55 -

Q-FlashTM
1. Q-Flash Del. BIOS.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M.I.T.) Select Language Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language F10: Save & Exit Setup Time, Date, Hard Disk Type.
ESC: Quit F8: Dual BIOS/Q-Flash
2. Dual BIOS/Q-Flash F8, Y.

Q-FlashTM / Dual BIOS

Q-Flash / Dual BIOS :
Dual BIOS Utility Boot From... Main Bios Main ROM Type/Size..SST 49LF003A Backup ROM Type/Size..SST 49LF003A

512K 512K

Dual BIOS

Dual BIOS

Q-FlashTM
Wide Range Protection Disable Boot From Main Bios Auto Recovery Enable Halt On Error Disable Copy Main ROM Data to Backup Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run "#:Move ESC:Reset F10:Power Off

BIOS. Enter.

Q-Flash

. Enter.

, Q-Flash/Dual BIOS. .

- 56 -

BIOS Q-Flash. , " ", BIOS . BIOS , Q-Flash . : 1. Q-Flash "Load Main BIOS from Floppy" Enter. BIOS, . BIOS , "Save Main BIOS to Floppy". 2. BIOS Enter. BIOS, 8KNXPU.Fba, . , BIOS, .
Wide Range Protection Disable 1 file(s) found Boot From Main Bios 8KNXPU.Fba 512K Auto Recovery Enable Halt On Error Disable Total size Copy Main ROM Data to Backup : 1.39M Free size : 911.50K F5 : Refresh DEL : Delete Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run "#:Move ESC:Reset F10:Power Off

BIOS, .

Enter. - BIOS .
Wide Range Protection Disable Boot From Main Bios Reading BIOS file from floppy. Auto Recovery Enable >>>>>>>>>>>>>>. Halt On Error Disable Copy Main ROM Data to Backup Don't Turn Off Power or Reset System Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run "#:Move ESC:Reset F10:Power Off

BIOS !!

BIOS BIOS: "Are you sure to update BIOS?" - 57
3. BIOS Y. BIOS. - . BIOS BIOS . 4. BIOS . Q-Flash.
Wide Range Protection Disable Boot From Main Bios Auto Recoverycompleted - Pass !! !! Copy BIOS Enable Halt On Error Disable Copy Main ROM Data to continue Please press any key to Backup Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run "#:Move ESC:Reset F10:Power Off

BIOS, 1 - 4.

5. Q-Flash Esc, Y. .
Wide Range Protection Disable Boot From Main Bios Auto Recovery Enable Are you sure to RESET ? Halt On Error Disable Copy Main ROM or to Backup [Enter] to continureData[Esc] to abort. Load Default Settings Save Settings to CMOS Q-Flash Utility Load Main BIOS from Floppy Load Backup BIOS from Floppy Save Main BIOS to Floppy Save Backup BIOS to Floppy Enter : Run "#:Move ESC:Reset F10:Power Off

BIOS.

Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-2003, Award Software, Inc. Intel i875P AGPset BIOS for 8KNXP Ultra Fba Check System Health OK , VCore = 1.5250 Main Processor : Intel Pentium(R) 4 1.6GHz (133x12) <CPUID : 0F27 Patch ID : 0027> Memory Testing : 131072K OK Memory Frequency 266 MHz in Single Channel Primary Master : FUJITSU MPE3170AT ED-03-08 Primary Slave : None Secondary Master : CREATIVEDVD-RM DVD1242E BC101 Secondary Slave : None

BIOS Fba

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For Xpress Recovery 09/23/2003-i875P-6A79BG03C-00

- 58 -

6. BIOS Del. Load Fail-Safe Defaults ( ) Enter . . BIOS .
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Select Language Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password Load Fail-Safe Defaults (Y/N)? Y PnP/PCI Configurations Set User Password PC Health Status Save & Exit Setup MB Intelligent Tweaker(M.I.T.) Exit Without Saving F3: Change Language F10: Save & Exit Setup Time, Date, Hard Disk Type.

Y. 7. Save & Exit Setup ( ) CMOS BIOS. . BIOS.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Select Language Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Save to CMOS and EXIT (Y/N)? Y Set Supervisor Password PnP/PCI Configurations Set User Password PC Health Status Save & Exit Setup MB Intelligent Tweaker(M.I.T.) Exit Without Saving F3: Change Language F10: Save & Exit Setup Time, Date, Hard Disk Type.

2: BIOS Q-Flash BIOS

BIOS Q-Flash BIOS.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software ! ! ! ! ! ! ! Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status MB Intelligent Tweaker(M.I.T.) Top Performance Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F3: Change Language F10: Save & Exit Setup Time, Date, Hard Disk Type.

Y.

- 59 -

Q-Flash :

Q-Flash Utility V1.30 Flash Type/Size..SST 49LF003A

Enter : Run

Keep DMI Data Enable Update BIOS from Floppy Save BIOS to Floppy "#:Move ESC:Reset

F10:Power Off

Q-Flash
. Enter. , Q-Flash. .

Q-Flash

BIOS QFlash. , " ", BIOS . BIOS , Q-Flash .
1. Q-Flash "Update BIOS from Floppy" Enter. BIOS, . BIOS , "Save BIOS to Floppy". 2. BIOS Enter. BIOS, 8GE800.F4, . , BIOS, . Q-Flash Utility V1.30
Flash Type/Size..SST 49LF003A 256K 1 file(s) found Keep DMI Data Enable 8GE800.F4 256K Update BIOS from Floppy Save BIOS tosize : 1.14M Floppy Total size : 1.39M Free Enter : Run ESC:Reset F10:Power Off F5 : Refresh "#:Move DEL : Delete Q-Flash Utility V1.30 Flash Type/Size..SST 49LF003A Keep DMI Data Enable Reading BIOS file from floppy. Update BIOS from >>>>>>>>>>>>>>. Floppy Save BIOS to Floppy Enter : Run "#:Move ESC:Reset Don't Turn Off Power or Reset System

BIOS

BIOS BIOS: "Are you sure to update BIOS?" BIOS BIOS . GA-8I915P-MF - 60 -
3. BIOS Y. BIOS. - .
Q-Flash Utility V1.30 Flash Type/Size..SST 49LF003A 256K
Keep DMI Data BIOS Now Updating Enable Update BIOS from Floppy >>>>>>>>>>>>>>>>>>>.. Save BIOS to Floppy Enter : Run "#:Move ESC:Reset F10:Power Off Don't Turn Off Power or Reset System

BIOS !!

4. BIOS . Q-Flash.
Q-Flash Utility V1.30 Flash Type/Size..SST 49LF003A Keep DMI Data Enable !! Copy BIOS completed - Pass !! Update BIOS from Floppy Save BIOS to Floppy Please press any key to continue "#:Move ESC:Reset 256K

Q-Flash Esc, Enter. .

Keep DMI Data Enable Are you BIOSto RESET ? Update sure from Floppy Save BIOS to Floppy [Enter] to continure or [Esc] to abort. Enter : Run "#:Move ESC:Reset F10:Power Off
Award Modular BIOS v6.00PG, An Energy Star Ally

BIOS

Copyright (C) 1984-2003, Award Software, Inc. Intel 845GE AGPSet BIOS for 8GE800 F4 Check System Health OK Main Processor : Intel Pentium(R) 4 1.7GHz (100x17.0) <CPUID : 0F0A Patch ID : 0009> Memory Testing : 122880K OK + 8192K Shared Memory Primary Master : FUJITSU MPE3170AT ED-03-08 Primary Slave : None Secondary Master : CREATIVEDVD-RM DVD1242E BC101 Secondary Slave : None
Press DEL to enter SETUP / Q-Flash 03/18/2003-I845GE-6A69YG01C-00
6. BIOS Del. Load Fail-Safe Defaults ( ). . 6 - 7 1.

!! BIOS !!

- 61 -

2 : @BIOSTM

, BIOS Gigabyte @BIOS. @BIOS BIOS Windows. BIOS. 1. @BIOS. 2. . @BIOS

//GIGABYTE/@BIOS

@BIOS Install

. 3. @BIOS

. 4. @BIOS

"!"

"Update New BIOS"

1. :

I. BIOS Internet. a. "Internet Update". b. "Update New BIOS". c. @BIOS. d. . e. BIOS. II. BIOS Internet: a. "Internet Update". b. "Update New BIOS". c. BIOS, "All Files". d. BIOS, ( , , 8I915PMF.F1). e. , BIOS. GA-8I915P-MF - 62 -
III. BIOS "Save Current BIOS". , BIOS. IV. -. "About this program". , , - .
I. I , . , . . II. II , BIOS , . . III. I BIOS @BIOS, BIOS Web- Gigabyte , II. IV.: BIOS , .

- 63 -

4-1-3 2- / 4- / 6- / 8-

6 2-/4-/6-/8- , .

Line In CD-ROM/DVD-ROM, . Line Out (Front Speaker Out) . Mic In . Rear Speaker Out . Center/Subwoofer Speaker Out . Side Speaker Out .
Line In Line Out (Front Speaker Out) Mic In
Rear Speaker Out Center/Subwoofer Speaker Out Side Speaker Out

Windows 98SE/2000/ME/XP . . ( , Windows XP.)
(). 1: Line Out. Line Out
2 : ("Sound Effect"). .

- 64 -

3: "Speaker Configuration", "2CH Speaker". .
1 : "Front Speaker Out", - "Rear Speaker Out".

Front Speaker Out

Rear Speaker Out
3 : "Speaker Configuration", "4CH Speaker". 4- .

- 65 -

1 : "Front Speaker Out", - "Rear Speaker Out", - "Center/Subwoofer Speaker Out".
Front Speaker Out Rear Speaker Out Center/Subwoofer Speaker Out
3 : "Speaker Configuration", "6CH Speaker". 6- .

- 66 -

1 : "Front Speaker Out", - "Rear Speaker Out", - "Center/Subwoofer Speaker Out", - "Side Speaker Out". 2 : ("Sound Effect"). .
Front Speaker Out Rear Speaker Out Center/Subwoofer Speaker Out Side Speaker Out
3: "Speaker Configuration", "8CH Speaker". 8 .

: .

- 67 -

Jack-Sensing

Jack-Sensing . Jack-Sensing Windows 98/98SE/2000/ME Microsoft DirectX8.1 .

, .

, Jack-Sensing , . , .

- 68 -

. Web- http://tw.gigabyte.com/faq/faq.htm. 1: BIOS , . ? : BIOS , ,. , BIOS Ctrl+F1. 2: / ? : , . 3: EasyTune 4? : EasyTune 4 . - EasyTune 4, . 4: RAID ATA Windows 2000 XP RAID, IDE3 IDE4? : -, CD-ROM . , . RAID, Web-. : http://tw.giga-byte.com/support/user_pdf/raid_manual.pdf) 5: CMOS? : Clear CMOS, , Clear CMOS . , , CMOS. : 1. . 2. . 3. 10 ( - , ). 4. . 5. . 6. Del, BIOS, Load Fail-Safe Defaults ( ). 7. . 6: BIOS ? : BIOS BIOS (Load Fail-Safe Defaults Load BIOS Defaults). , CMOS. 7: ? : , . ( ) - . 8: , ? : Gigabyte , . - 69
9: IDE 2? : , - , , USB Over Current Front USB. - , . 10: . ? : , . , . . $ AMI BIOS * . * 8, . 1 2 3 64 4 5 - gate A 8 / 9 10 / CMOS 11 - $ AWARD BIOS 1 : 2 : 1 1 : 1 2 : 1 3 : 1 9 : : : CMOS BIOS