Reviews & Opinions
Independent and trusted. Read before buy Gigaset SE567!

Gigaset SE567

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (Arabic)
Gigaset SE567, size: 2.5 MB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Gigaset SE567About Gigaset SE567
Here you can find all about Gigaset SE567 like manual and other informations. For example: reset, router, software, ip, wireless, setup, ip address, password.

Gigaset SE567 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Gigaset SE567 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Gigaset SE567 photo ]

Video review

Aliant: Siemens Gigaset SE567 issue with Real Palyer

 

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

Option B>required to setup your system for using the Gigaset Macintosh Configuration The steps Option A > Configure the PC 1: Configuring Windows
To setup the Gigaset device, you must first configure your PC to obtain an IP address from a DHCP server. Follow the procedure below: Note: The following procedures are for a PC running Windows XP. Please refer to the User Guide on the CD-ROM for help configuring other operating systems. 1. Click Start > Control Panel. 2. Double-click the Network Connections icon. 3. Double-click your Network Card. 4. Click Properties. 5. Select Internet Protocol (TCP/IP). 6. Click Properties. 7. Select Obtain an IP address automatically. 8. Select Obtain DNS server address automatically. 9. Click OK and exit out of the Control Panel. 10. Configure Internet Access using the procedure that follows.
Step 3 > Choose a Configuration Method
Option B > Configure the Macintosh
To setup the Gigaset device, you must first configure your computer to obtain an IP address from a DHCP server. Use the procedure below that corresponds to your system's operating system.
depend on whether you use a PC or a Macintosh. Select the appropriate option for your system.
2: Configuring Internet Access
Next, use the procedure below to make sure your PC will use the Gigaset device (and not Dial-up Networking) when connecting to the Internet. 1. Click Start > Control Panel. 2. Double-click the Internet Options icon. 3. Click the Connections tab.
4. Click Setup. 5. Click Next. 6. Click Connect to the Internet.
7. Click Next. 8. Click Setup my connection manually. 9. Click Next. 10. Select Connect using a broadband connection that is always on. 11. Click Next. 12. Click Finish. 13. Configure the Gateway using the procedure Configuring the Gateway.
ePM17640d.ipc01s0 g P3 021xesm_00_0 a : // qtoo1_e7

Troubleshooting

Power is off.

Power is on.

Blinking Green

Blinking Red/Green

Flash write in progress.

Quick-Start Guide

- POST in progress. - POST error occurred (if persistent). N/A

007-SE01-002

Configuring OSX
1. Click Apple > Preferences. 2. Select the Network icon under the Internet & Network section.

Configuring OS9

1. Click Apple > Control Panels > TCP/IP.
Ethernet 1-4 Wireless - Power not applied. - No link. - Power not applied. - No link. - Power not applied. - DSL Signal not detected. - Power not applied. - No LAN data activity. - Power not applied. - No WAN or LAN activity. - Power not applied. - No link. Normal operation, Link okay. Normal operation, Link okay. DSL line is trained and ready for traffic. - DSL link and WAN interface are up. - WAN interface has IP Address. N/A User traffic N/A flowing in either direction. Wireless user N/A traffic flowing in either direction. Steady blinkingDSL line is attempting to train. N/A N/A
2. Select Ethernet from the Connect via drop-down menu. 3. Select Built-in Ethernet from the Show drop-down menu. 4. Select Using DHCP Server from the Configure IPv4 drop-down menu. 5. Click Apply Now and exit the System Preferences window. 6. Configure the Gateway using the steps that follow. 3. Select Using DHCP Server from the Configure drop-down menu. 4. Close the window and save the changes. 5. Configure the Gateway using the steps that follow.

Activity Internet

LAN user traffic flowing in either direction.

Gigaset

SE567/SE568
Step 4 > Configure the Gateway
Windows ME and XP users: If you have Universal Plug and Play (UPnP) enabled, Windows may detect the Gigaset device upon startup and provide a shortcut to the device on the desktop. The icon will be labeled Residential Gateway. Double-click the icon and skip to step 3. If your PC has not been connected to a broadband modem or other network device, perform the PC configuration procedure below. Remember to restart each PC when finished. 1. Start your Web Browser. 2. In the address bar, type http://gigaset, then press Enter. The Gateway Setup Wizard appears to guide you through the setup process. 3. When you have completed the Gateway Setup Wizard, you can connect to the Internet or configure additional options on the Gateway.

USB (model SE568 only)

USB connected.
USB user traffic N/A flowing in either direction.
Residential Wireless Gateway
Gigaset Communications USA LLC 4849 Alpha Road Dallas, Texas 75244 (972) 852-1000 Fax (972) 852-1001 http://www.gigaset.com
Gigaset Communications GmbH 2008 Gigaset Communications GmbH is a trademark licensee of Siemens AG. All rights reserved. Subject to availability. Rights of modification reserved.
Congratulations! You have completed installing your Gigaset device.

A 8 - M- R1 - 2 - 1 9

Before you begin.
Verify that the following items came with your DSL kit:
Step 1 > Install Line Filters
Devices such as fax machines, caller ID boxes, or phones or phones that share the same phone line as your DSL account require a line filter. The line filter prevents noise from disrupting the DSL signal on the phone line. Filters can be in the form of a stand-alone line filter or a wall-mount filter.
Step 2 > Choose an Installation Method
The Gigaset SE567 device can only be connected to an Ethernet port; the Gigaset SE568 can be connected to an Ethernet or a USB port. To connect using an Ethernet port, complete the steps in Option A. To connect to a USB port, complete the steps in Option B.
Option B > USB Installation Method
Connect the Gigaset Device
1. Connect the USB cable to the USB port on the Gigaset device (blue port). 2. Connect the other end to the USB port on your computer. 3. Plug the DSL cable (RJ-11) into the DSL port on the Gigaset device (gray port). 4

Internet Connection

RJ-11 DSL Cable

Power Supply

1 Gigaset Device 2 Documentation 3 Software Manual/USB Drivers CD-ROM 4 Power Supply 5 RJ-45 Ethernet cable
Option A > Ethernet Installation Method
If your computer does not have an Ethernet Adapter installed, install it now. Refer to your Ethernet Adapter manufacturers documentation for complete installation instructions.
4. Plug the other end of the DSL cable (RJ-11) into the phone jack. 5. Plug the power adapter into the power outlet and Gigaset device (black port). 6. Ensure the Gigaset device is powered on (power switch located on the right side of back panel).

USB connection to computer

Stand-alone Line Filter

For each device that ahares the DSL phone line: 1. Unplug the device's cord from the phone jack. 2. Plug the filter into the phone jack.
Optional: Use Crossover (Xover) cable when connecting to a hub or switch without an uplink port
6 RJ-11 DSL cable 7 USB cable (SE568 only)
Windows USB Driver Installation
Connect the Gigaset Device 1. Connect the Ethernet cable (RJ-45) to the Ethernet port on the Gigaset device (yellow port). 2. Connect the other end to the Ethernet port on your computer. 3. Plug the DSL cable (RJ-11) into the DSL port on the Gigaset device (gray port). 4. Plug the other end of the DSL cable (RJ-11) into the phone jack. 5. Plug the power adapter into the power outlet and the Gigaset device (black port). 6. Ensure that the Gigaset device is powered on. The power switch is on the right side of the back panel. 4

Software Installation

Your service provider may include an Ethernet Adapter, a line filter, and a wall-mount filter in your DSL kit. If you received any of these items, follow the instructions provided in this guide for basic installation. For further assistance installing these items, contact your service provider.
3. Plug the phone cord (or other device cord) into the filter.
If you are using connecting the Gigaset device via the USB port, you must install USB drivers. Before installing the software make sure your PC is equipped with Windows 98, Windows 98 Second Edition (SE), Windows 2000 Professional, Windows Millennium Edition (ME), or Windows XP; 32MB RAM; Pentium-compatible 166MHz or faster processor; 12MB available hard disk space. 1. Insert the Gigaset Installation CD in to your CD-ROM drive to automatically start the software installation program. Follow the on-screen directions to complete the installation. 2. After the USB driver is installed, continue with the PC Configuration procedures described on the next page. If the software installation program does not start automatically, start it manually: 1. Click Start > Run. 2. Browse to setup.exe on the CD and double-click it to start the program.
A PCI Ethernet Adapter B Line filter(s) C Wall-mount filter
Ethernet Connection to Computer RJ-45 Straight-through Ethernet cable

Wall-mount Filter

For a wall-mounted phone, use a wall-mount filter: 1. Remove the phone from the wall. 2. Connect the wall-mount filter to the all plate.

Optional: Use Crossover (Xover) cable when connecting a hub or switch without an uplink port

3. Reconnect the phone.

You have completed the installation of your Gigaset hardware. There is no software installation required when using an Ethernet connection. If you have the router model, proceed to Step 3 to configure your router and connect to the Internet.
Macintosh USB Driver Installation
Before installing the software, make sure your system is running OS 8.6 or above. This procedure will restart your computer to complete the installation. 1. Insert the Gigaset Installation CD into your CD-ROM drive. 2. Open the Gigaset icon from the desktop. 3. Click Readme.txt. Follow the directions in Read me.txt to complete the software installation. 4. After the USB driver is installed, continue with the PC Configuration procedures described on 5 the next page.

doc1

007_se01_001_print.qxd

26.02.2007

Seite 1

A31008-M9207-R101-1-7619

Quick-Start Guide

007-SE01-001

Gigaset

SE567/SE568
Residential Wireless Gateway
Gigaset Communications GmbH is a trademark licensee of Siemens AG

Seite 2

Before you begin.
Verify that the following items came with your DSL kit:
1 Gigaset Device 2 Documentation
3 Software Manual/USB Drivers CD-ROM 4 Power Supply 5 RJ-45 Ethernet cable
6 RJ-11 DSL cable 7 USB cable (SE568 only)
Your service provider may include an Ethernet Adapter, a line filter, and a wall-mount filter in your DSL kit. If you received any of these items, follow the instructions provided in this guide for basic installation. For further assistance installing these items, contact your service provider.
A PCI Ethernet Adapter B Line filter(s) C Wall-mount filter

Seite 3

Step 1 > Install Line Filters
Devices such as fax machines, caller ID boxes, or phones or phones that share the same phone line as your DSL account require a line filter. The line filter prevents noise from disrupting the DSL signal on the phone line. Filters can be in the form of a stand-alone line filter or a wall-mount filter.

Stand-alone Line Filter

For each device that ahares the DSL phone line: 1. Unplug the device's cord from the phone jack. 2. Plug the filter into the phone jack. 3. Plug the phone cord (or other device cord) into the filter.

Wall-mount Filter

For a wall-mounted phone, use a wall-mount filter: 1. Remove the phone from the wall. 2. Connect the wall-mount filter to the all plate. 3. Reconnect the phone.

Seite 4

Step 2 > Choose an Installation Method
The Gigaset SE567 device can only be connected to an Ethernet port; the Gigaset SE568 can be connected to an Ethernet or a USB port. To connect using an Ethernet port, complete the steps in Option A. To connect to a USB port, complete the steps in Option B.
Option A > Ethernet Installation Method
If your computer does not have an Ethernet Adapter installed, install it now. Refer to your Ethernet Adapter manufacturers documentation for complete installation instructions.
Connect the Gigaset Device 1. Connect the Ethernet cable (RJ-45) to the Ethernet port on the Gigaset device (yellow port). 2. Connect the other end to the Ethernet port on your computer. 3. Plug the DSL cable (RJ-11) into the DSL port on the Gigaset device (gray port). 4. Plug the other end of the DSL cable (RJ-11) into the phone jack. 5. Plug the power adapter into the power outlet and the Gigaset device (black port). 6. Ensure that the Gigaset device is powered on. The power switch is on the right side of the back panel. 4

Internet Connection

RJ-11 DSL Cable

Power Supply

Ethernet Connection to Computer RJ-45 Straight-through Ethernet cable
Optional: Use Crossover (Xover) cable when connecting a hub or switch without an uplink port
You have completed the installation of your Gigaset hardware. There is no software installation required when using an Ethernet connection. If you have the router model, proceed to Step 3 to configure your router and connect to the Internet.

Seite 5

Option B > USB Installation Method

Connect the Gigaset Device
1. Connect the USB cable to the USB port on the Gigaset device (blue port). 2. Connect the other end to the USB port on your computer. 3. Plug the DSL cable (RJ-11) into the DSL port on the Gigaset device (gray port). 4. Plug the other end of the DSL cable (RJ-11) into the phone jack. 5. Plug the power adapter into the power outlet and Gigaset device (black port). 6. Ensure the Gigaset device is powered on (power switch located on the right side of back panel).
USB connection to computer
Optional: Use Crossover (Xover) cable when connecting to a hub or switch without an uplink port
Windows USB Driver Installation

Software Installation

If you are using connecting the Gigaset device via the USB port, you must install USB drivers. Before installing the software make sure your PC is equipped with Windows 98, Windows 98 Second Edition (SE), Windows 2000 Professional, Windows Millennium Edition (ME), or Windows XP; 32MB RAM; Pentium-compatible 166MHz or faster processor; 12MB available hard disk space. 1. Insert the Gigaset Installation CD in to your CD-ROM drive to automatically start the software installation program. Follow the on-screen directions to complete the installation. 2. After the USB driver is installed, continue with the PC Configuration procedures described on the next page. If the software installation program does not start automatically, start it manually: 1. Click Start > Run. 2. Browse to setup.exe on the CD and double-click it to start the program.

USB Drivers

Windows/Mac OS September 2006 007-SE03-001
Global network of innovation

trad emar ks of

tive pec ir res Sieme by the ns A G, Germ held any. All other trademarks are

ies. pan com

Macintosh USB Driver Installation
Before installing the software, make sure your system is running OS 8.6 or above. This procedure will restart your computer to complete the installation. 1. Insert the Gigaset Installation CD into your CD-ROM drive. 2. Open the Gigaset icon from the desktop. 3. Click Readme.txt. Follow the directions in Read me.txt to complete the software installation. 4. After the USB driver is installed, continue with the PC Configuration procedures described on 5 the next page.
For Windows: Close all applications. Load the CD into drive. Installation will run automatically. If not, go to My Computer. Right-click and open the CD drive. Double-click on setup.exe.

res erves

ice. not out to ma e with ke ch any tim anges to product s pecifications at

Cop yrigh t

6 SIEM ENS SUBSCR IBER
NET WORKS, I NC. All rights

. Sie rved rese

s and men

ens Siem

Seite 6
Option B> Macintosh Configuration
Step 3 > Choose a Configuration Method
The steps required to setup your system for using the Gigaset depend on whether you use a PC or a Macintosh. Select the appropriate option for your system.
Option A > Configure the PC 1: Configuring Windows
To setup the Gigaset device, you must first configure your PC to obtain an IP address from a DHCP server. Follow the procedure below: Note: The following procedures are for a PC running Windows XP. Please refer to the User Guide on the CD-ROM for help configuring other operating systems. 1. Click Start > Control Panel. 2. Double-click the Network Connections icon. 3. Double-click your Network Card. 4. Click Properties. 5. Select Internet Protocol (TCP/IP). 6. Click Properties. 7. Select Obtain an IP address automatically. 8. Select Obtain DNS server address automatically. 9. Click OK and exit out of the Control Panel. 10. Configure Internet Access using the procedure that follows. 4. Click Setup. 5. Click Next. 6. Click Connect to the Internet.
2: Configuring Internet Access
Next, use the procedure below to make sure your PC will use the Gigaset device (and not Dial-up Networking) when connecting to the Internet. 1. Click Start > Control Panel. 2. Double-click the Internet Options icon. 3. Click the Connections tab.
7. Click Next. 8. Click Setup my connection manually. 9. Click Next. 10. Select Connect using a broadband connection that is always on. 11. Click Next. 12. Click Finish. 13. Configure the Gateway using the procedure Configuring the Gateway. 6

Seite 7

Option B > Configure the Macintosh
To setup the Gigaset device, you must first configure your computer to obtain an IP address from a DHCP server. Use the procedure below that corresponds to your system's operating system.

Configuring OSX

1. Click Apple > Preferences. 2. Select the Network icon under the Internet & Network section.

Configuring OS9

1. Click Apple > Control Panels > TCP/IP.
2. Select Ethernet from the Connect via drop-down menu. 3. Select Built-in Ethernet from the Show drop-down menu. 4. Select Using DHCP Server from the Configure IPv4 drop-down menu. 5. Click Apply Now and exit the System Preferences window. 6. Configure the Gateway using the steps that follow. 3. Select Using DHCP Server from the Configure drop-down menu. 4. Close the window and save the changes. 5. Configure the Gateway using the steps that follow.
Step 4 > Configure the Gateway
Windows ME and XP users: If you have Universal Plug and Play (UPnP) enabled, Windows may detect the Gigaset device upon startup and provide a shortcut to the device on the desktop. The icon will be labeled Residential Gateway. Double-click the icon and skip to step 3. If your PC has not been connected to a broadband modem or other network device, perform the PC configuration procedure below. Remember to restart each PC when finished. 1. Start your Web Browser. 2. In the address bar, type http://gigaset, then press Enter. The Gateway Setup Wizard appears to guide you through the setup process. 3. When you have completed the Gateway Setup Wizard, you can connect to the Internet or configure additional options on the Gateway.

Congratulations! You have completed installing your Gigaset device.

Seite 8

Troubleshooting

Power is off.

Power is on.

Blinking Green

Blinking Red/Green

Flash write in progress.

- POST in progress. - POST error occurred (if persistent). N/A

Ethernet 1-4 Wireless

- Power not applied. - No link. - Power not applied. - No link. - Power not applied. - DSL Signal not detected. - Power not applied. - No LAN data activity. - Power not applied. - No WAN or LAN activity. - Power not applied. - No link.
Normal operation, Link okay. Normal operation, Link okay. DSL line is trained and ready for traffic. - DSL link and WAN interface are up. - WAN interface has IP Address. N/A
User traffic N/A flowing in either direction. Wireless user N/A traffic flowing in either direction. Steady blinkingDSL line is attempting to train. N/A N/A

Internet

Activity
LAN user traffic flowing in either direction.

USB (model SE568 only)

USB connected.
N/A USB user traffic flowing in either direction.
Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. Subject to availability. Rights of modifications reserved. www.gigaset.com
A31008-M9207-R101-1-7619_18-10-2008

 

Tags

Ip Deskjet 650C MX 40 Suunto X9I Roland RS-5 MRO-DV100 PCG-X18 HT-X70 C-460zoom TX-PF42g10 Password KX-TG6422E Nevada DJ72 Oslo 502 DD55C Actros HL-6050DN Cube R700 KDL-52W4500 E-300 EWT811 Suunto Core KDL-37W5720 Garageband 2 Wireless IC-P4CT CH-X400 Dslr-A380L LH-T912SB Sensor BAR CDX-GT63UIW 1680 PRO LP-1400 LPF 6200 UR5U-8500L Lowrance X91 TDR125 E2725B Fujifilm A820 NS125DLX ECM20 HVR-HD1000P 1244-4IU Roadnavigator RN10 I 1200 WR250F-2004 Hilti PD22 DG-20 Quad 22L Electronics M6 TX32LX85P AVR 45 Slider 28DG21C HQ7340 NV-U83 EMX512SC EP720 Media Home DIR-615 DR-202 Olympus X-41 NP2500 A3100 IS S12AHP 46A65M GP1200-2000 Chronis IB Wintv-nova 21PT5433-78R SR2024C PM7200 V360I KV-32FQ86B P405M UX-D57CL EC 700 P5Q-EM FAX Cnip CT-M5R VDR-D160EP PM3500M Ws PRO Filter Favorit 475 32PFL7403D MZ-42PM13 MY100X Software HD080HJ-B Ip Address Series 42PFL7433D 12 Setup Router VS8F-2 249-4 Easy 270 FBU55 Lrsc26911TT DR-MV1 GR-432SFA VS8F-1 Creatis Base Reset Aviat 617 CDM-7872RB FAX-phone L75

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101