MP3 Player MW3847 2GB INSTRUCTION MANUAL

Warnings and Precautions

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol, located on back or bottom of the unit, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol, located on back or bottom of the unit, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Any use of the controls or an adjustment to the procedures other than those specified herein may result in hazardous radiation.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
To reduce the risk of electric shock, do not remove cover (or back). There are no user-serviceable parts inside. Please refer any servicing to qualified service personnel.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the users authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Features

The button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste

Features Defined

1 LCD Display View the track, track time, and song info. through this Liquid Crystal Display.
2 Plus Press the Plus button to increase the volume. 3 PREV/SEARCH Press the PREV/SEARCH button to skip to the previous track. Press and hold the PREV/SEARCH button to search backwards through a song 4 Minus Press the Minus button to decrease the volume. 5 NEXT/SEARCH Press the NEXT/SEARCH button to skip to the next track. Press and hold the NEXT/SEARCH button to search forward through a song. 6 Dual Headphone Jacks Use the Dual Headphone Jacks to plug in one or two sets of headphones. 7 Mini-USB Port Use the Mini-USB Port to connect the MP3 Player to a computer via the included USB Cord. 8 USB Cord Use the USB Cord to connect the MP3 Player to a computer. 9 Hold/Un-Hold Use the Hold/Un-Hold toggle switch to lock or unlock the buttons on the MP3 Player. 10 PLAY/PAUSE Press the PLAY/PAUSE button to play or pause the MP3 Player, or hold the PLAY/PAUSE button to turn the MP3 Player off and on. 11 M (Mode) Press the M (Mode) button to switch between MTP and USB mode when connected to a computer. 12 R (Repeat) Press the R (Repeat) button to cycle through the following repeat modes; REP

System Requirements

Microsoft Windows 98SE, ME, 2000 Professional, XP

Home/Professional Edition CD-ROM Drive USB Driver compatible with Microsoft Windows ME, 2000 Professional, and XP. Multi-CPU or Multi-Boot environments are not supported.
Customers with Windows 98/98SE computer need to go to our website, www.gpx.com, to download the appropriate drivers for the MP3 Player.

Connecting to a Computer

1. Turn on the MP3 Player by holding the PLAY/PAUSE button. 2. Take the USB Cord and plug the corresponding ends into the MP3 Player and a Computer. 3. When connected the LCD Display will either say USB or MTP. 4. Press the M (mode) button to switch between USB and MTP mode. MTP mode will only work, when your player is connected to Microsoft Windows XP and Windows Media Player 10. The MP3 Player will only work in USB mode when it is connected to Windows 98SE, ME, or 2000 Professional.
Using Windows Media Player 9
1. Start Windows Media Player 9 and connect the MP3 Player to your computer. 2. Click Copy to CD or Device. 3. In the drop-down list, on the Items to Copy pane, click the play list, category, or other item that you want to copy. 4. Clear the check boxes next to any files you do not want to copy. 5. In the drop-down list, on the Items to Copy pane, click the device that you want to copy files to. 6. Click the Copy button. 7. Repeat steps 2-5 for any other items that you want to copy to your unit.
Using Windows Media Player 10
1. Start Windows Media Player 10 and connect the unit to your computer. On your players display it should say MTP. If not, then while the unit is connected press the M (mode) button to change from USB to MTP mode. 2. If you have not set up synchronization between your computer and this device, the Device Setup Wizard starts. In the Device Setup Wizard, select Manual. 3. Click Finish. 4. Select Library option. On the right pane select Sync List. 5. From the left pane you can select the Play list or Library and you will see the content songs in the center pane. 6. Select the songs from the center pane, drag and add them to the Sync List. 7. Click the Start Sync button in the Sync List pane. 8. Repeat steps 4-7 for any other items that you want to copy to your unit.

Service Information

Address Phone Fax Email Website
2116 Carr Street, St. Louis MO, 63106 1-314-621-2881 1-314-588-1805 prodinfo@gpx.com www.gpx.com Para descargar este manual de instruccin en ingls, espaol, o francs visite la seccin de la ayuda en www.gpx.com. Pour tlcharger ce manuel dinstruction en anglais, espagnol, ou le Franais visitez la section de soutien www.gpx.com.
To download this Instruction Manual in English, Spanish, or French visit the Support section at www.gpx.com. 2007 DPI, Inc.

USERS GUIDE

BC219B PORTABLE CD PLAYER WITH AM/FM RADIO CONTENTS WARNINGS AND PRECAUTIONS 2 IMPORTANT SAFETY INSTRUCTIONS 2 QUICK START 3 CD/AUX MODE....3 AM OR FM MODE...3 GENERAL PRODUCT INFORMATION 4 IN THE BOX...4 FEATURES....4 POWERING THE UNIT & REMOTE 5 UNIT POWER OPTIONS...5 REMOTE POWER OPTIONS...5 OPERATIONS 6 PLAYING A CD...6 PROGRAMMING A CD...6 OPERATIONS 7 TUNING THE AM/FM RADIO....7. USING THE AUXILIARY INPUT...7 UNIT CONTROLS & FEATURES 8 UNIT CONTROL GLOSSARY 9 REMOTE CONTROLS & FEATURES 10 REMOTE CONTROL GLOSSARY 11 COMPANY INFORMATION 12 GREEN INITIATIVE...12 INTERNATIONAL SUPPORT...12 SERVICE INFORMATION...12.
For the most up-to-date version of this Users Guide, go to www.GPX.com

WARNINGS AND PRECAUTIONS

This symbol, located on back or bottom of the unit, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS
1. 2. 3. 4. 5. 6. 7. Read these Instructions. Keep these Instructions. Heed all Warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding -type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
This symbol, located on back or bottom of the unit, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This product utilizes a Class 1 laser to read Compact Discs. This laser Compact Disc Player is equipped with safety switches to avoid exposure when the CD door is open and the safety interlocks are defeated. Invisible laser radiation is present when the CD Players lid is open and the systems interlock has failed or been defeated. It is very important that you avoid direct exposure to the laser beam at all times. Please do not attempt to defeat or bypass the safety switches. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. To reduce the risk of electric shock, do not remove cover (or back). There are no user-serviceable parts inside. Please refer any servicing to qualified service personnel. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. WARNING: To prevent fire or shock hazards, do not expose this unit to rain or moisture. WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. PRCAUTION: Danger dexplosion si les piles sont remplaces de faon incorrect. Remplacer les piles seulement par le mme type de pile ou lquivalent. WARNING: The remote controls button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
13. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. L appareil ne doit pas tre expos aux coulements ou aux claboussures et aucun objet ne contenant de liquide, tel quun vase, ne doit tre plac sur lobjet. 14. Battery shall not be exposed to excessive heat such as sunshine, fire, or the like. Les piles ne doivent pas tre exposes de forte chaleur, tel qu la lumire du soleil, au feu ou autres choses de semblable. 15. Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. La prise du secteur ne doit pas tre obstrue ou doit tre facilement accessible pendant son utilisation. Pour tre compltement dconnect de lalimentation dentre, la prise doit tre dbranche du secteur. 16. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 17. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 18. Excessive sound pressure from earphones and headphones can cause hearing loss. 19. Des pressions acoustiques excessives provenant dcouteurs ou de casques peuvent provoquer des pertes de laudition. 20. To prevent fire or shock hazard, do not use this plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.
21. Symbol is used to indicate that a specific component shall be replaced only by the component specified in that documentation for safety reasons.
22. This symbol indicates that this product incorporates double insulation. 23. Caution marking is located at the rear of apparatus. Les prcautions demploi sont inscrites en bas de lappareil.

QUICK START 1. Plug the BC219 into an AC outlet or insert 8 C batteries into the battery compartment.
2. Adjust the Source Switch on the side of the unit to CD/Aux, AM, or FM mode.
CD/AUX MODE 1. Open the CD Door and load a CD into the unit.
AM OR FM MODE 1. Extend the FM antenna to improve FM reception. An AM antenna is built into the unit. Adjust the position of the unit to improve AM reception.
2. Press the Play/Pause Button to begin playing the loaded CD. 2. Turn the Tuning Dial to adjust the AM or FM radio station.
GENERAL PRODUCT INFORMATION IN THE BOX BC219 - Portable CD Player with AM/FM Radio Remote Control Detachable AC Cord Users Guide & Warranty
FEATURES CD player: CD, CD-R/RW AM/FM stereo radio with digital readout Auxiliary input Remote Programmable CD tracks Repeat play Analog volume control Built-in stereo speakers Stereo headphone jack AC power DC power: requires 8 C batteries, not included Includes: detachable AC cord, remote control
POWERING THE UNIT & REMOTE UNIT POWER OPTIONS AC Power Detachable AC Cord (included)
DC Power Requires 8 C batteries (not included)
REMOTE POWER OPTIONS DC Power Requires 1 CR2025 battery (included)

CR2025

RY TTE BA M 25 IU 20 TH CR 3V
Y ER TT BA 5 M 202 HIU CR 3V

IU CR M B 2 AT 3V 025 TE

OPEN PUSH
OPERATIONS PLAYING A CD Disc compatibility: CD, CD-R/RW 1. Adjust the Source Switch to CD/Aux Mode. PROGRAMMING A CD Before Programming a CD, read through the Playing a CD instructions. 1. After the CD is loaded and ready to play, press the Program Button to begin programming the CDs tracks.
2. Open the CD Door and load a CD into the unit.
2. Press the Skip/Search Buttons to select the track to play first. 3. Press the Program Button to program the selected track. 4. Repeat steps 2-3 to continue programming tracks numerically. Up to 20 CD tracks can be programmed at one time. 5. Press the Repeat Button once to repeat all of the programmed tracks. Press the Repeat Button twice to repeat an individual track from the programmed list.
3. Press the Play/Pause Button to begin playing the loaded CD.
4. Press the Stop Button to stop the CD during play. 5. Press the Skip/Search Buttons to skip between tracks on the loaded CD. Press and hold the Skip/Search Buttons to search through individual tracks on a loaded CD. 6. Press the Repeat Button once to repeat the current CD track. Press the Repeat Button twice to repeat an entire album. Please note: When an audio source is connected to the Auxiliary Input and a CD is loaded, the Auxiliary Input connection will take priority. To play a CD, disconnect the Auxiliary Input. 6

OPERATIONS TUNING THE AM/FM RADIO 1. Adjust the Source Switch to AM or FM radio modes. USING THE AUXILIARY INPUT 1. Adjust the Source Switch to CD/Aux Mode.
2. Turn the Tuning Dial to adjust the AM or FM radio station.
2. Connect an MP3 Player or other audio source to the Auxiliary Input. Connecting an audio source to the Auxiliary Input requires a cord with a 3.5 mm mini-phono plug.
The FM Stereo Indicator (FM ST) illuminates when the FM radio is in stereo mode. Extend the FM antenna to improve FM reception. An AM antenna is built into the unit. Adjust the position of the unit to improve AM reception.
3. Use the connected devices controls to play, pause, stop, and skip between tracks on the connected device. Please note: When an audio source is connected to the Auxiliary Input and a CD is loaded, the Auxiliary Input connection will take priority. To play a CD, disconnect the Auxiliary Input.
UNIT CONTROLS & FEATURES 03 04
UNIT CONTROL GLOSSARY 01. Play/Pause Buttons Press the Play/Pause Buttons to play or pause a loaded CD. 02. Skip/Search Buttons Press the Skip/Search Buttons to skip between tracks on a loaded CD. Press and hold the Skip/Search Buttons to search through an individual track on a loaded CD. 03. Program Button Press the Program Button to program the tracks of a loaded CD to play in a particular order. 04. Stop Button Press the Stop Button to stop a CD during play. 05. Repeat Button Press the Repeat Button once to repeat the current CD track. Press the Repeat Button twice to repeat the entire CD. 06. LCD Display 07. CD Door Open the CD Door using the finger grip at the bottom of the door. Please note, the CD Door must be closed for a loaded CD to play. 08. FM Antenna Extend and adjust the FM Antenna to improve FM radio reception. An AM Antenna is built into the unit. Adjust the position of the unit to improve AM radio reception. 09. Source Switch (CD, Aux, Power Off, AM, FM) Adjust the Source Switch to activate CD, Aux, Power Off, AM, or FM modes. 10. Tuning Dial Turn the Tuning Dial to adjust the current AM or FM radio station. 11. Volume Dial Turn the Volume Dial to adjust the volume of audio output from the unit. 12. Headphone Jack Use the Headphone Jack to connect a set of earbuds or headphones to the unit. 13. Auxiliary Input Use the Auxiliary Input to connect an MP3 player or other audio source to the unit. 14. AC Power Input Use the AC Power Input to connect the included detachable AC cord to the unit. 15. Battery Compartment (Requires 8 C batteries, not included)

REMOTE CONTROLS & FEATURES
REMOTE CONTROL GLOSSARY 16. Repeat Button Press the Repeat Button once to repeat the current CD track. Press the Repeat Button twice to repeat the entire CD. 17. Program Button Press the Program Button to program the tracks of a loaded CD to play in a particular order. 18. Play/Pause Button Press the Play/Pause Buttons to play or pause a loaded CD. 19. Skip/Search Buttons Press the Skip/Search Buttons to skip between tracks on a loaded CD. Press and hold the Skip/Search Buttons to search through an individual track on a loaded CD. 20. Stop Button Press the Stop Button to stop a CD during play. 21. FM Indicator Displays when in FM radio mode. 22. AM Indicator Displays when in AM radio mode. 23. Radio Station Displays the current AM or FM radio station. 24. CD Track Displays the current track of a loaded CD. 25. FM ST. Indicator The FM Stereo Indicator illuminates when the FM radio is in stereo mode.
COMPANY INFORMATION GREEN INITIATIVE Environmental Commitment to Protect for Today and Sustain for Tomorrow 2009 marks the official launch of DPI, Inc.s corporate campaign for a greener and cleaner world. DPI and its four brands, iLive, WeatherX, Capri, and GPX, are building upon environmental initiatives introduced at all of their facilities to help formulate and sustain significant and important conservation efforts within its manufacturing and marketing communities. In addition to targeting and selecting energy efficient product features, and structuring green office procedures, other initial program efforts include: Reduction of all packaging sizes Recyclable plastics for clamshell packages, with a plan to eventually replace plastic with recyclable paper Recycled fiber board in place of the polyfoam in packing boxes Recycled plastics in place of the virgin material in product construction
INTERNATIONAL SUPPORT To download this Users Guide in English, Spanish, or French, visit the support section at www.gpx.com. Para transferir esta gua de usuario en ingls, espaol, o francs, visite la seccin de la ayuda en www.gpx.com. Pour tlcharger ce guide de lutilisateur en anglais, espagnol, ou franais, visitez la section de soutien chez www.gpx.com.
SERVICE INFORMATION Address: 2116 Carr Street, St. Louis MO, 63106 Phone: 1-314-621-2881 Fax: 1-314-588-1805 Email: prodinfo@gpx.com Parts Email: partsinfo@dpi-global.com Website: www.gpx.com
2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are subject to change without notice