Grsslin (UK) Ltd

Tel : Fax : 01732 354445
INSTALLATION & OPERATING INSTRUCTIONS
SOCKET BOX DIGITAL SBST DIGI INSTALLATION GENERAL NOTES:
1. 2. 3. INSTALLATION SHOULD BE CARRIED OUT IN ACCORDANCE WITH THE CURRENT EDITION OF THE I.E.E. WIRING REGULATIONS. THE TIMER SHOULD NOT BE MOUNTED ON AN UNEARTHED METAL OR METALLISED SURFACE. IF THE TIMER IS TO BE CONNECTED TO AN APPLIANCE THAT IS REQUIRED TO BE EARTHED THE SUPPLY EARTHING CONDUCTOR AND THE APPLIANCE EARTHING CONDUCTOR SHOULD BE TERMINATED TOGETHER IN THE EARTH TERMINAL PROVIDED WITHIN THE TIMER.

INSTALLATION PROCEDURE:

1. SWITCH THE SUPPLY OFF AT THE MAINS. MEANS OF DISCONNECTION FROM THE SUPPLY HAVING AT LEAST 3MM CONTACT SEPARATION IN ALL POLES MUST BE INCORPORATED IN THE FIXED WIRING MAINS SUPPLY. UNSCREW THE TWO SCREWS LOCATED TOP RIGHT AND BOTTOM LEFT OF FRONT MODULE COVER, REMOVE COVER AND GENTLY PULL MODULE FROM BACKPLATE. DO NOT PUT UNDUE STRESS ON, OR INTERFERE WITH FIXED BLUE WIRE. BARE WIRES BACK FOR 6mm (1/4inch) MAXIMUM; INSERT INTO TERMINALS AND SECURE WITH THE SCREWS, IN ACCORDANCE WITH CIRCUIT DIAGRAM LABEL BENEATH TERMINALS. FIX BACKPLATE TO SOCKET BOX. CONNECT WIRING IN ACCORDANCE WITH WIRING DIAGRAM. FIT COVER OVER MODULE AND REASSEMBLE TO BACKPLATE. ENSURING FIXED BLUE WIRES ARE STOWED NEATLY WITHOUT BEING TRAPPED. RE-FIT AND TIGHTEN COVER. SWITCH ON MAINS.

3. 4. 5. 6. 7.

SETTING UP / PROGRAMMING SETTING THE CLOCK
1/ PRESS AND HOLD THE CLOCK FACE BUTTON 2/ SET THE CURRENT DAY, HOUR AND MINUTE ( D,H,M) 3/ ONCE YOU HAVE SET THE DAY, HOUR AND MINUTE, RELEASE THE CLOCK FACE BUTTON

SETTING THE PROGRAMMES

1/ PRESS AND RELEASE THE PROG BUTTON 2/ INPUT THE DAY OR DAYS, HOURS AND MINUTES (D,H,M) 3/ PRESS THE HAND BUTTON ONCE, CIRCLE WITH A DOT SHOULD APPEAR ON DISPLY INDICATING AN ON COMMAND 4/ PRESS PROG BUTTON AND REPEAT STEP 2 TO SET UP OFF TIME 5/ PRESS HAND BUTTON TWICE, CIRCLE WITHOUT A DOT TO INDICATE OFF COMMAND 6/ REPEAT STEPS 1 THROUGH 5 IF YOU WISH TO INPUT MORE PROGRAMME SETTINGS 7/ PRESS AND RELEASE THE CLOCK FACE BUTTON TO RETURN TO NORMAL TIME 8/ PRESS THE PROG BUTTON SEQUENTIALLY TO REVIEW OR CHANGE YOUR PROGRAMME SETTINGS 9/ WHEN DISPLAY SHOWS BLANKS WHERE THE TIME SHOULD BE, THIS IS YOUR NEXT PROGRAMME SLOT 10/ PRESS THE PROG BUTTON ONCE MORE AND AN FR NUMBER WILL BE DISPLAYED. THIS IS THE AMOUNT OF PROGRAMME SPACES UNUSED. NOW SIMPLY PRESS THE CLOCK FACE BUTTON TO RETURN TO NORMAL TIME. IMPORTANT NOTE: IF FOR EXAMPLE YOU WANT THE UNIT TO COME ON AT 6 AM TILL 6 PM AND YOU ARE SETTING THIS PROGRAMME UP AT 11 AM THEN WHEN YOU FINISH YOU WOULD EXPECT THE TIMER TO COME ON. THIS IS NOT THE CASE, THE REASON IS THAT YOU HAVE ALREADY PASSED THE ON TIME, (6AM). TO OVER COME THIS SIMPLY PRESS THE HAND BUTTON AND THE HAND SYMBOL WILL SHOW IN THE DISPLAY AND THE UNIT WILL COME ON. THE TIMER WILL NOW STAY ON UNTIL NEXT PROGRAMMED OFF TIME AND SWITCH BACK TO TIMED MODE READY FOR NEXT PROGRAM

Grsslin (UK) Ltd

Tel : Fax : 01732 354445

SPECIFICATION SHEET

Socket box timer synchronous & digital
PRODUCT CODE SBSTUZH SBSWUZH DIGISB 24 hour synchronous 7 day synchronous 24 hour / 7 day digital 16 Amps 16 Amps 16 Amps
All products are suitable for fitting to a standard depth power socket box, and will provide timed control for any fixed-wiring device up to a resistive load of 16 amperes. Synchronous units are supplied in 24 hour or 7 day versions, incorporate a manual (Fix On / Timed / Fix Off) control and are without battery reserve. The digital version has a self-resetting override, plus Fixed On / Fixed Off selection, and incorporates a battery reserve, retaining the time display and programming in the event of a mains failure.

Technical specification:

Fitting Dimensions Suits standard power socket box 92mm square, 40mm projection, 15mm depth into box. 160g
Weight AC switching capacity: - resistive load 16A 250v AC - inductive load cos 0.6 8A 250v AC - incandescent lamp load 1350W - fluorescent lamp load 60W Minimum switching current 100mA (20v) AC/DC Ambient temperature: - Synchronous units -20 0C to +550C - Digital units -20 C to +55 C Accuracy mains synchronized typ. 2.5 sec. / day Battery charging time (quartz) 70 hours Minimum switching time: - 24 hour dials 15 minutes - 7 day dials 2 hours - digital unit 1 minute Synchronous manual override fix ON / timed / fix OFF Digital manual override Advance / fix ON / timed / fix OFF