DIGITAL LCD TELEVISION INSTRUCTION MANUAL
MODEL: LT26R3A , LT26K3A LY26R3A , LY26K3A LTF32R3A , LTF32K3A LY32R3A , LY32K3A LTF42R3A , LTF42K3A LTF42R3B , LTF42K3B
Please read this manual carefully before operating the unit, and keep it for future reference.

Contents

01 Safety Warnings
Welcome Important information P.02 P.03

02 About your LCD TV

Get to know your TV Get to know your remote control Connecting your TV Preparation of your remote control P.06 P.08 P.09 P.11

03 Getting Started

Setting up Tuning your TV Common interface Using your TV Adjusting picture settings Adjusting sound settings Function settings Time settings Lock menu settings Shortcut menu display P.12 P.13 P.16 P.18 P.19 P.20 P.21 P.23 P.25 P.27

04 Using the features

Teletext function USB mode Using External USB Disk For Recording Using your DVD player(certain models only) P.29 P.31 P.38 P.40

05 Reference Sections

Troubleshooting Specification P.44 P.45

Safety Warnings WELCOME

Thanks for buying this 26"/32"/42" HD Ready Digital LCD TV. This guide will help you set up and begin using your TV. First, check the contents of your box with the parts checklist below: 26"/32"/42"HD Ready Digital LCD TV Remote control AAA battery x2 Instruction Manual

Now you can get started!

IMPORTANT INFORMATION

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. *To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any accessory inside the casing. *If necessary, please contact authorized after-sales services. *A lighting flash mark in a triangle: A potentially hazardous situation, which, if not avoided, could result in serious injury by high voltage. *An exclamation mark in a triangle: Major part or accessory of which technical specifications must be followed if it is to be replaced.

Warning :

To avoid fire or electric hazards, never place your television receiver in an area with heavy moisture. Attention should be paid to avoid accidental scratches or impacts onto the screen.

Caution:

Please read this manual carefully before using your television and keep this manual in a good place for future reference. To achieve the best performance of your television, read this User's Manual carefully and properly store it for future reference. Information of screen displays and figures in the User's Manual may vary due to technical innovations.
Unauthorized disassembly of this product is prohibited.
The product should be tightly fixed to avoid drop damages and even fire.
To avoid fire hazards, do not use this product under direct sunlight or closely to heat sources.
Do not locate the product close to water or oil, which may cause fire hazards.
Unplug the power supply and antenna of the product when there is a rainstorm, especially Thunderstorm.
Do not use damaged or worn electric plugs and keep electric cord away from heat sources to avoid electric shocks or fire hazards.
Do not connect excessive sockets in parallel or share the same socket by multiple plugs to avoid fire hazards.
The product must be placed on a solid and stable surface to avoid collapse.
Unauthorized disassembly of the television is prohibited to avoid electric shocks or fire hazards. Contact authorized after-sales service if technical service is needed.
Keep the product away from a transformer or heat source to avoid fire hazards.
Disconnect the product from power supply and contact authorized after-sales service if abnormal sound is heard in the product.
Don't use or store inflammable materials near the product to avoid explosion or fire hazards.
Don't place the product in a humid area to avoid fire hazards.
The antenna of the product should be away from electric cable to avoid electric shocks.
Never touch the plug when your hand is wet as this might cause electric shocks.
Always make sure that the televisionis well plugged as poor electric connection might cause fire.
When antenna is used, measures should be taken to prevent water from flowing down along the cable into the television.
Unplug the television, use soft fabric, never chemicals, if you are going to make cleaning of the product. Make sure that no water drops in the product.
The plug and electric cable must be kept clean to avoid electric shocks or fire hazards.
Disconnect the television from power supply and antenna when there is a rainstorm or thunderstorm to avoid electric shocks or fire hazards.

CONNECT A DVD PLAYER TO YOUR TV

L R Y Pb Pr

Connect the DVD video outputs (Y, Pb, Pr) to the COMPONENT (Y, Pb, Pr) IN socket on your TV. 1. Turn on the DVD player and insert a DVD. 2. Press the button to select. 3. Refer to the DVD player user guide for operating instructions.
CONNECT A DVD PLAYER OR VCR TO YOUR TV
There are two ways in which you can connect a DVD player or VCR to your TV. Make sure that both the TV and DVD player or VCR are switched off before you connect them.

Connection Option 1

1.Connect the audio and S-VIDEO cables from the VCR output jacks to the TV input jacks. 2.Insert a video tape into the VCR and press PLAY on the VCR. 3.Turn on the power of the TV first, then the VCR. 4.Press the SOURCE button on the TV to set the video input mode to S-VIDEO.

Connection Option 2

1.Connect the AV DVD/VCR outputs to the AV IN socket on your TV. 2.Press the SOURCE button on the TV to set the video input mode to AV.

SCART INPUT

1.Connect the scart lead from the external device (DVD player, Set-top box or games console) to the TV scart socket. 2.Press the SOURCE button to select SCART mode. 3.Press the PLAY button on the external device.

HDMI INPUT

1.Connect the cable from the HDMI device to the TV HDMI socket. 2.Press the SOURCE button to select HDMI mode. 3.Refer to the HDMI device user guide for how to operate.
MOUNT YOUR TV ONTO THE WALL
You can mount your TV onto the wall by using a wall bracket (not supplied). Use M4/M6 machine screws (4 pcs) to screw the TV onto the bracket (not supplied).
PREPARATION OF YOUR REMOTE CONTROL

BATTERY INSTALLATION

1.Place the remote control face down, then open the cover of the battery compartment.
2.Install two AAA batteries. (The + and- symbol of the battery must match with the marks on the remote).
3.Close the cover of the battery compartment.

BATTERY CAUTION

Confirm there is no object between the remote control and the remote sensor of the TV set. Sunshine or other strong light will interfere with the signal sent by the remote control. In this situation turn the TV set to avoid the direct light source. Do not put the remote control in direct heat or in a damp place as you may damage the remote. Please use two AAA 1.5V batteries. Do not mix battery types. Install the batteries at the correct polarities. Do not use rechargeable batteries. If your TV is to be stored for a period of time, remove the batteries from the remote control.

Getting Started

Setting up

LOCATION

You will need to place your TV near your plug socket (so the power cable can comfortably reach) and within reach of your aerial socket or extension lead.

CONNECTION

1. Insert your TV aerial lead into the Antenna input at the side of the TV. 2. Insert the batteries into the remote control. Make sure they are inserted the right way around, matching the polarity as indicated inside the battery compartment.

SWITCHING YOUR TV ON

1.Press the STANDBY button on the right side of the TV once. A red flashing light will appear in the corner of the screen. 2.Press STANDBY on the remote control. The TV will turn on and the red light will turn blue. This may take a few moments. 3.Select your chosen language when prompted from the list that will appear on screen. Use the button to scroll to the language you want and press to confirm.

TUNING YOUR TV

SWITCHING TO AN EXTERNAL SOURCE OTHER THAT TV
If you have attached a DVD player or similar external device to the TV, you will need to tell the TV to display the content from it. Simply press SOURCE which will bring up the source menu in the left corner of the screen, Use the and button to highlight the required source and press OK select. For details of how to plug in other equipment see GET TO KNOW YOUR TV on page 6.
Input Source TV AV SCART1 SCART2 S-Video Component1 Component2 PC HDMI1 HDMI2 HDMI3 USB Input Source TV AV SCART1 SCART2 S-Video DVD Component PC HDMI1 HDMI2 HDMI3 USB

AUTO SEARCH

1. Press MENU button. 2. Press button to select Tuning menu, press button to enter. 3. Press button to select Country item. Press button to select you needed. 4. Press button to select Auto Search item, press OK button to enter. Press button to select the OK option, and press OK button to start searching. Press the MENU button ,you can choose to skip the TV /DTV Search or not. 5. Press EXIT button to stop auto search during searching. Note: It may take a few moments to complete the Auto Search.

OK OK OK OK OK OK

OK OK OK OK OK OK OK OK

OK CANCEL OK

DIGITAL MANUAL SEARCH
1. Press MENU button. 2. Press button to select Tuning menu, press button to enter. 3. Press button to select Digital Manual Search item, press button to enter. 4. Press button to select the Channel. Press OK button to start searching. 5. Once a channel is located, you can press OK button to save it. Press EXIT button to exit.

UHF CH

Analog Manual Search
Follow the below steps when you need to have a manual search. Menu 1. Press MENU button. 2. Press button to select Tuning menu, press button to enter. 3. Press button to select Analog Manual Search item, Press button to enter. 4. Press button to select Search item, press button is used to select the higher frequency channel. Press button is used to select the lower frequency channel. 5. And then select Storage To, press button to select the position number you want the channel on. Once a channel is located, you can press red button to save it. Press EXIT button to exit.

Sound System Press button to select "Sound System", then press button to select the correct sound system. Current CH Press button to select the channel number to edit. Storage To Press button to select the program number you want to storage to. Fine tune If the picture and/or sound are poor, try using the FINE TUNE feature. Do not use this feature unless reception is poor. 1 Repeat above steps 1-3, then press button to select the Fine Tune item. 2 Press button repeatedly to carry out fine tune, till the best picture and sound are obtained, then loosen the button.

Channel Edit

Using this function ,you can rename, move, set favorite channel and skip the channel in the analogue mode. 1.Press MENU button. 2.Press button to select TUNING menu, press button to enter. 3.Press button to select CHANNEL EDIT item, Press button to enter the sub-menu.You can press red, green , yellow or blue button to enter the menu you need. RENAME 1.Press button to select the channel , and press green button to rename. 2.Press button to select the number position of channel name, Press button to select number. 3.You can press the EXIT button to cancel the changes at anytime. NOTES:The RENAME function is only available in ATV program.

SKIP FAV

MOVE 1.Press button to select the channel any press yellow button to select the position. 2.Press button to select the number position you want to remove to, press yellow button to confirm. 3.You can press the EXIT button to cancel the changes at anytime. Setting favourite channel 1.Press button to select the channel ,press Red button to set your favourite channel. 2.You can press the Red button to cancel the changes at anytime. 3.Press FAV button on the remote control and Favourite List will be displayed. 4.Press button to select the channel , and press OK button to enter. SKIP 1.Press button to select the channel and press blue button to skip the current channel. 2.You can press the blue button to cancel the changes at anytime. GUIDE (Electronic Program Guide) Using this function ,you can access the DTV program information 1.Press MENU button. 2.Press button to select TUNING menu. press button to enter. 3.Press button to select the guide item. Press OK button to enter the submenu, the electronic program guide is displayed. You can quickly call up Guide menu by GUIDE button on the remote control. Notes: Only DTV mode.

BBC ONE Wales

Record

Schedule

REMIND

COMMON INTERFACE

The common interface (CI) slot is designed to accept the Conditional Access (CA) Module and Smart card in order to view the pay TV programmes and additional services. Contact your Common Interface service provider to get more information about the modules and subscription. Please noted that CA modules and smart cards are neither supplied nor optional accessories from us.
Warning: switch off your TV before any module is inserted in the Common Interface slot. CI Module Insert
Insert the CAM correctly, then Smart Card to the CI slot that is located at the side of the TV.
Main Menu Module information Smart card information Language Software Download Press OK to select,or Exit toquit
Turn on the TV and it will display the below message if the CA module is detected. Wait for few moments until the card is activated. Press the MENUbutton to display the Main Menu and use the and button to highlight the "CI information" line and press the "OK" button.

CI module removed

Detailed information on the CI card in use is displayed. Press OK button to access the card menu. Refer to the module instruction manual for setting details When module is removed, the following message will appear on the screen.

Software Update function

When you get the updating news from the TV shop's web, you can update the operating software using the Download menu. The data for various units are transferred consecutively on a special receiving channel. You need to search the channel with updating code stream. Note: You can get information from the TV shop or internet.

Operation

1 Press MENU button. 2 Press press 3 Press 4 Press button to select TUNING menu, button to enter. button to select Software Upgrade item. button to set it as On. The default is Off

OK OK OK OK OK

Are you sure?
5 If the updating code stream of the channel is suitable for your set, Do System Update option can be selected. Otherwise the Do System Update option is grey and cannot be selected. 6 Press button to select the System Update option and use OK button to enter. Then the TV will restart and search the upgrade information. NOTES: If the upgrade information is received, the TV will begin to upgrade. Or else, the TV will be back the DTV source. 7 Load the receiver identification. This process may also take several minutes. you can press EXIT button to cancel the download and your TV set will be standby. 8 After the download has finished, your TV set will enter burning state and the indicator light is shining. The menu 4 of right appears. The set will be standby when the update is completed.

USING YOUR TV

How to select the TV program
1.Using Program number button Enter the channel number with the number keypad on the remote control. 2.Using P+/P- button Press the P+/P- button to select a channel number.

HOW to adjust volume

Press V+/V- button on the remote control or the side of the TV to adjust the volume level.

CH.LIST function

Press CH.LIST button on the remote control will display Channel List menu, and then press button to enter. Press button to select the channel, and then press OK button to enter.
ADJUSTING PICTURE SETTINGS
Changing the Picture Setting 1. Press MENU button. 2. Press button to select Picture menu, press button to enter. 3. Press button to select the item requires adjusting. 4. Press button to adjust the selection item. 5. When you are satisfied with your choice, press the EXIT button to return to normal viewing or press MENU button to return to the previous menu. Contrast This will adjust the intensity of bright parts in the picture but keep the dark parts unchanged. Brightness This will adjust the light output of the complete picture, which will mainly affect the darker areas of the picture. Colour This will adjust the saturation level of the colours to suit your personal preference. Sharpness This will adjust the sharpness of fine details in the picture. Tint Allows you to select the colour mix (Tint) of the picture. Note: The Tint function is only available in NTSC mode. Mode This will select the picture mode. Select Standard/Mild/User/Vivid according to the program. You can quickly select the desired mode by P.MODE button on the remote control. Colour temperature This will increase or decrease Warm (red) and Cool (blue) colours to suit personal preferences. Select Cool to give the white colour a blue tint, Normal to give the white colour a neutral tint, Warm to give the white colour a red tint. Noise Reduction Automatically filters out and reduces the image noise and improves picture quality when receiving weak video signals. Select Off/Low/Standard/High according to the image noise. Reset To recover to the default value.

ADJUSTING SOUND SETTINGS

Changing the Sound Setting
1. Press MENU button. button to enter. 2. Press button to select Sound menu, press 3. Press button to select the item requires adjusting. Menu < 4. Press button to adjust the selection item. Balance < Mode 5. When you are satisfied with your choice, press the EXIT AVL < SRS TS XT < button to return to normal viewing or press MENU button to Digital Audio Output< Equalizer return to the previous menu. Audio Languages

OK OK OK

Standard Off Off Off English
>0 > > > >

Balance

Picture

Tuning

Function
This will adjust the output of the right and left speakers to obtain the best stereo reproduction for your listening position.
This will select the sound mode. Press button to select Standard/Music/Theater/User according to the program. You can quickly select the desired mode by S.MODE button on the remote control.
AVL (Automatic volume control)
This will reduces the differences in volume level among broadcasters.

SRS TS XT

This will control the Woofer output. Press button to select SRS TS XT. Press button to set SRS TS XT as OFF, ON.
Digital Audio Output This will control the Digital Audio Output. Press button to select Digital Audio Output., Press button to set Digital Audio Output. as OFF, PCM,RAW.

Equalizer

This sound setting can be adjusted to suit your personal preference.

Audio Languages

Press press Press button to select Primary/Secondary item, and then button to select the languages you needed. button to select Close item, Press OK button to close it.
< Balance < Mode AVL < SRS TS XT < Digital Audio Output< OK Equalizer Audio Languages OK Reset OK

Picture Sound Tuning

Note: The Audio Language function is only available in DTV mode.
To recover to the default menu setting.

FUNCTION SETTINGS

1. Press MENU button. 2. Press button to select Function menu, press button to enter. 3. Press button to select the item requires adjusting. Menu 4. Press button to adjust the selection item. 5. When you are satisfied with your choice, press the EXIT button to return to normal viewing or press MENU button to return to the previous menu.
Language To select the menu language. Subtitle Language To select the Subtitle language.
Display Mode To set the picture proportion, press button to select 4:3/Zoom1/Zoom2/Wide/16:9/Auto. You can quickly select the desired mode by ARC button on the remote control. 4:3 mode Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides. 16:9 mode Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. Zoom1 Choose Zoom1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. Zoom2 Choose Zoom2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage. Wide Choose Wide when you want to adjust the picture in a non-linear proportion, that is, more enlarged at top sides and no alteration, at bottom side. Blue Screen This will select the character background colour. Note: The Blue Screen function is only available for ATV mode. Recorder To recorder the DTV program. Details of Recorder are described in the page of 38. SCART Input When you use the SCART2 input ,make sure the input source is AV or S-VIDEO,and set the SCART INPUT option.

Source Lock

Source Lock will control the On or Off of hinder external input modes. Press button to set as on or off. When the source lock is set as on, TV source will display, at this time, when press SOURCE button, the TV can switch to correspondingsource and will display the Source is locked.

Max Volume

Press button to select Max Volume. Press button for adjustment between 0-100. If a certain Value is set, when volume is being adjusted, the sound value can not exceed maximum volume value. If current volume is over Max Volume, when lock set menu is set, current volume will become set maximum volume, if current volume is below maximum volume, customer set volume will stay unchanged.

Initial Volume

The TV will remember it after your setting,that will be the volume when turn on the TV next time.

Parental Lock

Press button to select parental lock. Press the age of children who will watch TV. button to select OFF or 4-18 to limit

Clear Lock

Press button to select Unlock mode. Press button to unlock all set modes, setting all lock options to off, and the maximum volume returns to 100.

SHORTCUT MENU DISPLAY

Subtitle Function
1. Press SUBTITLE button on the remote control will display Subtitle languages menu, press button to enter. 2. Press button to select the item and press OK button to enter. You can press the EXIT button to cancel the changes at anytime. Notes: press SUBTITLE button on the remote, it will display subtitle languages menu only in the DTV mode.
Subtitle Languages off English

Channel List

CH.LIST Function
1. Press CH.LIST button on the remote control, will display Channel List menu. 2. Press button to select the channel and press OK button to enter. You can press the EXIT button to cancel the changes at anytime.

GUIDE Function

Press GUIDE button on the remote control, will display Program Guide menu, press button to select the program. You can press the EXIT button to cancel the changes at anytime. Notes: Available only in the DTV mode.

INFO Record Schedule DATE REMIND OK

FAV Function

Press FAV button on the remote control, will display Favourite List menu. Press button to select program and press OK button to enter. You can press the EXIT button to cancel the changes at anytime.
Press INFO button on the remote control, will display the current channel information. You can press the EXIT button to cancel the changes at anytime.
Press AUDIO button on the remote control, will display Audio Languages menu. Press button to select the desired settings and press OK button to enter. You can press the EXIT button to cancel the changes at anytime. Notes: Press AUDIO button on the remote, it will display Audio Languages menu only in the DTV mode.

Eliminate Sound

When you need to pay attention to surrounded sounds, or there is a telephone calling you or there are some guests visiting you, the sound elimination (mute) function is very convenient.
1 Press the MUTE button on the remote control and "Mute" type face will display on the lower part of the screen. At this Time, the sound of the TV set is turned off. 2 If you want to recover the sound, press the MUTE button again or directly press V+ button.

Quick program view

This function enables quick swap to the last watched program. Press Q.view button, and the TV will be back to the TV source, expect in the USB and DVD source. 1 Suppose the channel number you used just now is 8 and the channel number you are using is 18 (as shown in the figure). 2 If you want to return to the last watched program channel 8, you can simply press the Q.View button. 3 If you want to return to channel 18, press the button again. Use this function, you can easily change between the channel you are using and the channel you used last Timer.

Using the features

Teletext functions
Teletext is an information system, broadcast by certain channels, which can be read like a newspaper. It also provides subtitles for people with hearing difficulties or those who are unfamiliar with the language in which a particular program is being broadcast (cable networks, satellite channels, etc.). Note: The teletext buttons could be working even if there is no teletext signal, but there is no teletext display.

Teletext

Teletext functions To select teletext press the button on the handset. To switch off teletext, press the button again. Note all menu functions are not available in teletext mode. Only a few direct button control functions are available in teletext mode, they are: Volume adjustment Mute function Page up/down Use the P+/P- buttons to browse next or previous page.
Page number entering To select a Teletext page, enter the page number using the numeric key pad on the remote control, or use the P+ or P- buttons, or the coloured Fast text buttons. Mix mode To view the TV picture while in Text mode press the button, this will superimpose the Teletext data on top of the TV picture. Press this button again to return to Full text. INDEX Press the INDEX button to go to the index page of teletext.

4. Press on the remote control unit to select the required file, press OK button / to enter the selected file.
5. To exit the streaming media playing system and watch a TV program, you must press BACKbutton to return to the streaming media main menu at first(to protect equipment), and then press SOURCE to select TV to return to the TV mode.
Notes: 1. Under source of US B , when press button MENU , screen goes black, except when images or movies are being played. 2.While playing the USB ,press BACKbutton repeatly , the screen picture will return to USB main interface, and only at this time you can switch corresponding signal sources by pressing SOURCE again. 3. Please do not unplug the USB device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.

Operating the USB device

1. Press option. 2.Press OK to confirm your selection. 3.Press
to scroll through main menu or submenu and select your desired
to achieve the FWD (fast forward) and REV (fast back) of the
option being played. 4. Press "PLAY/PAUSE" to play and press it again to pause playing. and
5. Press ZOOM to magnify pictures; when the picture is enlarged, press /

to move the picture.

6.Press STOP
to stop playing ,or return to the previous menu, and press BACK
repeatedly to return to the main menu.
NOTE: You can choose the photos or music in different files to play together.

Playing a Picture

1.After entering USB main interface, press to select PHOTO item. /
2.Press OK to confirm the selection and enter the picture file list.
3. Press to select the picture you / want to play press OK to confirm, and then press PLAY/PAUSE button to play the pictures.
4. If you want to pause the picture which is being palyed, press the PALY/PAUSE button again.

Press / Press Press

ZOOM to magnify the picture. When the picture is enlarged, press to move the picture. PREV/NEXT to select the last or next picture.
to rotate the picture. to stop the picture being played. repeatedly.

Press STOP

5.To exit playing, just press BACK
NOTE: The menu display varies with the photo name and pixel in your equipment.

Playing Music

1. After entering USB main interface, press to select MUSIC. /
2. Press OK to confirm the selection and enter the music file list.

/ 3. Press PLAY/PAUSE

and OK button to select the music you want to play button to play the music.

then press

Press played. Press
to achieve the REV (fast back) and FWD (fast forward) of the musicbeing

PREV/NEXT to select the last or next music. to stop the music being played,when the current interface is the music

Press STOP being played.

4. To return to the main menu

just press

repeatedly.
NOTE: You can enjoy the music and the picture at the same time.

Playing a Movie

1. After entering USB main interface, press to select Movie. /
2. Press OK to confirm the selection and enter the movie file list.
3. Press and OK button to select the movie you want to play and then press / PLAY/PAUSE button to play the movie.
Press ZOOM to magnify the picture Press PREV/NEXT to select the last or next movie. Press STOP to stop the movie being played.
4. To exit playing, just press BACK repeatedly.
1. After entering USB main interface, press to select Text. /
2. Press OK to confirm the selection and enter the text file list.
/ 3. Press and OK buttonto select the text you want to play and then press PLAY/PAUSE button to play the text.
Press PREV/NEXT to select the last or next text.

4. To exit the

Text mode
NOTE: You can enjoy the music and the text at the same time.
Using External USB Disk For Recording
1. Insert the USB device with FAT32 format into the USB1 connector. Then, press MENU button. Note: Only USB1 is available for recording. 2.Press button to select FUNCTION menu, press button to enter. 3.Press button to select Recorder. Press OK button to enter the submenu. 4.Press button to Select Disk and press or OK button to enter. Press button to select disk if your device has several disks. 5.Press button to select Format and press to enter. Press button to select the size you want to format.Press OK button to format the USB Disk. NOTES: The system will format the whole device and if your device size is bigger than 1GB, you can set the size which is used for time shift. 6.Format may take several minutes and the time is depending on the memory size. Press button to select the Time Shift Disk Size. The max device size for Time Shift is 8GB.Then, press OK button to save. NOTES: If you select all the size format for time shift, you can not do any recording.
Menu Select Disk Check File System USB Disk Format Time Shift Size Speed File System Size File System Size SD 27Min OK All HD7Min

USB1 C: start

CANCEL
Format Do not unplug USB device Formating..
Time Shift Size Time Shift Size SD 14Min OK All HD4Min CANCEL
7.Waiting for the system checking. And you can see the speed data after the success checking. NOTES: 1. Only have to format when you use the device for record for the first time. 2. The minimum device size for record is 1GB. Provide device formatting function is up to 2TB. The max Multi-Partition is 16 partitions and one is active at a time. 3. Bit rate: Device bit-rate>4.5MB/s REC is safe at HD stream Device bit-rate>1.5MB/s REC is safe at SD stream Device bit-rate<600KB/s REC is bad for REC 4. The system can not work normally if the USB device have the listing problem below: The device has bug. The device has error block. The device reports the unfaithful size.

PLAYING A JPEG CD 1.Insert a JPEG CD in the same way as you would a DVD or Audio CD, with the label facing away from you. 2.The CD will load and a menu of the disc's contents will appear on screen. 3.Use the and buttons to highlight the folder and picture you wish to view and press PLAY/PAUSE. Each image on the disc will show consecutively, like a slide show. 4.Press PLAY/PAUSE during the slide show to pause on one image. 5.Press the or button to skip to the next image or return to the previous one. PLAYING AN AUDIO CD 1.Insert a CD in the same way as you would a DVD, with the label facing away from you. 2.The CD will load and a menu of the disc's contents will appear on screen. 3.Use the and buttons to highlight the track you wish to play and press PLAY/PAUSE, or just press PLAY/PAUSE to listen to the whole CD from the beginning. You can stop, pause, fast forward or fast rewind a CD in the same way as a DVD. You can also use the REPEAT button to repeat a track, folder album or the contents of the whole disc. Press repeatedly to select what you would like to repeat. You can also use the A-B function to repeat a certain section of a track or CD.

TROUBLESHOOTING

To assist in location of possible faults use the help guide below:
Verify if the television is properly plugged in. Verify if the television has a proper supplied power source. Verify if electricity is available. Verify if correct signals are input. Operate the remote to change signal input to correct input. Restart the television if power supply is interrupted. Press MUTE button and verify if Mute mode is set. Switch to other channel and verify if the same problem happens. Press VOL+ button to see if the problem can be solved. Verify if sound system is correct. Refer to user's manual for adjustment. Verify if correct channel is selected. Adjust the antenna.

No picture, no sound

Blank screen

No sound

Poor sound
No picture in some channel No color for some channel program (black and white)
Verify if the same problem exists in other channels. Check out of picture and sound systems. Refer to relative instructions in the Manual for color adjustment. Verify if the antenna is correctly connected. Verify if the antenna is in good condition. Make fine adjustment of channel. Disconnect the television from power supply and 10 seconds later, connect the television to the power supply. If the problem still exists, contact authorized after-sales service for technical assistance.

DIGITAL LED LCD TELEVISION

INSTRUCTION MANUAL

Please read this manual carefully before operating the unit, and keep it for future reference.

Contentss

01 Safety Warnings 2
Welcome...2 Important Information..2 Safety notice...3 Electrical connections..4

02 About your LED LCD TV

Get to know your TV..5 Get to know your remote control..7 Connecting your TV...8 Preparation of your remote control.9

03 Getting Started

Setting up...9. Tuning your TV.. 10 Common interface... 11 Using your TV... 12 Adjusting picture settings... 12 Adjusting sound settings.. 13 Function settings... 13 Channel managment.. 14 Time settings... 15 Lock menu settings... 15 Shortcut menu display.. 17

04 Using the features

Teletext functions.. 19 USB mode... 20. Using external USB disk for recording.. 21

05 Reference Sections

Troubleshooting... 22 Specification... 23
Digital LED LCD Television Instruction Manual

01 Safety Warningss

WELCOME
Thanks for buying this 19"/22" HD Ready Digital LED LCD TV. This guide will help you set up and begin using your TV. First, check the contents of your box with the parts checklist below: 19"/22" HD Ready Digital LED LCD TV Remote control AAA battery 2 Instruction Manual Warranty TV stand Now you can get started!

IMPORTANT INFORMATION

READ ALL INSTRUCTIONS BEFORE USE AND KEEP FOR FUTURE REFERENCE.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).NO USER SERVICEABLE PARTS INSIDE. FOR ANY PROBLEMS, REFER SERVICING TO THE CUSTOMER HELP LINE. THERE IS A LIGHTNING ARROW SYMBOL IN THE TRIANGLE: THIS SYMBOL INDICATES HIGH VOLTAGE IS PRESENT INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT WITH ANYINSIDE PART OF THIS PRODUCT. THERE IS A EXCLAMATION MARK IN THE TRIANGLE: THIS SYMBOL ALERTS YOU THAT IMPORTANT LITERATURE CONCERNING OPERATION AND MAINTENANCE HAS BEEN INCLUDED WITH THIS PRODUCT. CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE, DO NOT PUT THE TV SET NEAR SOURCES OF HUMIDITY. DO NOT USE ANY ABRASIVE CLEANERS WHICH MAY SCRATCH OR DAMAGE THE LCD SCREEN. AVOID CONTACT WITH OBJECTS THAT MAY SCRATCH THE LCD SCREEN. NOTE: SERVICING THE UNIT YOURSELF IS UNAUTHORISED AND COULD LEAD TO INJURY OR PRODUCT DAMAGE. REFER ALL SERVICING TO THE CUSTOMER HELPLINE.

SAFETY NOTICE

For your protection,please read these instruction completely and keep this manual for future reference. Please ensure that the set has adequate ventilation. Do not place the set near a heat source or in direct sunlight. Do not put the unit near water or oil as it may cause a fire. During thunderstorms, unplug both the antenna and power plug to prevent damage. Do not use a damaged power plug or put the power supply near a heat source as it may cause electric shock or fire. To prevent potential fire, do not overload an electrical outlet with too many plugs. Place the set on a level surface to prevent it from tipping and potential damage. Do not remove the cover of the set or try to service your TV. This may result in electrical shock or fire. All service work must be completed by an authorised technician.
To prevent fire, do not use or store any flammable materials near the unit. To prevent fire, do not place the unit near a damp wall. To prevent electric shock, ensure that any external antenna connected to the set is clear of contact with any power lines. Do not plug/unplug the unit while your hands are wet. This may cause an electric shock. Please ensure a solid connection with the AC wall socket in order to avoid shock and potential fire. To prevent electric shock or fire, please prevent rain from entering the set along the wire connected to the outside antenna. When cleaning, please unplug the unit. Use a soft cotton cloth. Do not use any abrasive cleansers, and prevent water from entering the set. If any plugs or input wires are dirty, unplug the set and clean them. This will prevent the risk of electric shock or fire. If the set is not going to be used for an extended period, unplug the unit from the main power.
The apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as vases should be placed on the apparatus. The mains plug is used for disconnecting the device, make it easily accessible. Do not use any accessories that are not recommended by the manufacture.

01 Saftety Warnings

If there are any abnormal sounds or smells from the unit, unplug it immediately and contact an authorised service provider.
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH HOUSEHOLD WASTE. PLEASE RECYCLE WHERE FACILITIES EXIST. CHECK WITH YOUR LOCAL AUTHORITY FOR RECYCLING ADVICE. TruSurround XT, SRS and the symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is

Prepartion of your remote control

Battery installation

A the remote control face down, then open the Place
cover of the battery compartment.

GettingStarted

Setting up

Location

You will need to place your TV near your plug socket (so the power cable can comfortably reach) and within reach of your aerial socket or extension lead.
B Install two AAA batteries. (The + and - symbol of
the battery must match with the marks on the remote).

Connection

A Insert your TV aerial lead into the Antenna input at the
Insert the batteries into the remote control. Make sure B they are inserted the right way around, matching the polarity as indicated inside the battery compartment. side of the TV.
C Close the cover of the battery compartment.

Switching your TV on

A the POWER button on the right side of the TV Press
once. A red flashing light will appear in the corner of the screen. Press B POWER on the remote control. The TV will turn on and the red light will turn blue. This may take a few moments. Select your chosen language when prompted from the C list that will appear on screen. Use the34 button to scroll to the language you want and press OK button to confirm.

Battery caution

Confirm there is no object between the remote control and the remote sensor of the TV set. Sunshine or other strong light will interfere with the signal sent by the remote control. In this situation turn the TV set to avoid the direct light source. Do not put the remote control in direct heat or in a damp place as you may damage the remote.

TUNING YOUR TV

Please use two AAA 1.5V batteries. Do not mix battery Switching to an external source other types. Install the batteries at the correct polarities. that TV Do not use rechargeable batteries. If your TV is to be stored for a period of time, remove the batteries from If you have attached a DVD player or similar external device the remote control. to the TV, you will need to tell the TV to display the content from it. Simply press SOURCE which will bring up the source
menu in the right corner of the screen, use the 5 and button to highlight the required source and press OK select. For details of how to plug in other equipment see Get to konw your TV on page 5.

Source TV DTV AV SCART Component PC HDMI USB

Current CH Country

Tuning

9 United Kingdom Select

Coulor System PAL Sound System DK Auto Search Manual Search Skip Off
B 5 button to select Tuning menu, press 4 Press
button to enter. Press C 5 button to select Manual Search,then press 4 button to start searching. Press D MENU button to stop Manual Search during searching.

Auto search

A MENU button. Press

Current CH

Press 34 button to select the channel number to edit.

United Kingdom Select

Colour System
Press button to select Colour System, then press 4 button to select the correct colour system.

Sound System

Press button to select Sound System, then press 4 button to select the correct sound system.
To skip the channel when press P+/P- button by setting the Skip button On.
button to enter. Press C 5 button to select Country item. Press 34 button to select you needed. Press D 5 button to select Auto Search item, press 4button to start searching. Press E MENU button to stop auto search during searching. Note It may take a few moments to complete the Auto Search.

Fine tune

If the picture and/or sound are poor, try using the FINE TUNE feature. Do not use this feature unless reception is poor. Repeat above steps 1-3 ,then press button to A select the Fine Tune item. Press B 34 button repeatedly to carry out fine tune, till the best picture and sound are obtained, then loosen the button.

Manual search

COMMON INTERFACE
The common interface (CI) slot is designed to accept the Conditional Access (CA) Module and Smart card in order to view the pay TV programmes and additional services. Contact your Common Interface service provider to get more information about the modules and subscription. Please noted that CA modules and smart cards are neither supplied nor optional accessories from us.
Warning Switch off your TV before any module is inserted in the Common Interface slot. Insert the CAM correctly, then Smart Card to the CI A slot that is located at the side of the TV.

CI Slot

H When module is removed, the following message
will appear on the screen.

Message

CI Module Removed

Software Update function

Smart Card
B on the TV and it will display the below message Turn
if the CA module is detected. Wait for few moments until the card is activated.

When you get the updating news from the TV shops web, you can update the operating software using the Download menu. The data for various units are transferred consecutively on a special receiving channel. You need to search the channel with updating code stream. Note

CI Module Inserted

CI Module is OK

Operation

Press C the MENU button then press 56 button to select TUNING menu, press 4 button to enter
Channel Management Country Auto Search Manual Search Time Option Version 1.6.0826 United Kingdom Select
Press D 56 button to select Option item, press 4 button to enter.

Option

Audio Language Subtitle Language Guide CI Information Parental Lock Parental Rating Software Upgrade Off

English

Select
Press E 56 button to select displayed.

CI Information option.

Detailed information on the CI card in use is F Press G OK button to access the card menu. Refer to the module instruction manual for setting details.
B 56 button to select TUNING menu, press 4 Press
button to enter. Press C 56 button to select Option item, press 4
You can get information from the TV shop or internet.
button to enter. Press D 56 button to select option. Press E 34 button to set it as On. (The default is Off )
Start system upgrade Do you want to upgrade your TV? , Don t turn off your TV or touch any button! YES NO

Software Upgrade

Press V+/V- button on the remote control or the side of the TV to adjust the volume level.
ADJUSTING PICTURE SETTINGS
Changing the Picture Setting
A MENU button. Press Press B 5 button to select Picture menu, press 4
button to enter. Press C 5 button to select the item requires adjusting.
Menu Contrast Brightness Colour
If F the upgrade information is received, the TV will begin to upgrade. Load G the receiver identification. This process may also take several minutes. You can press EXIT button to cancel the download.
Updating Download-Don t turn off the TV! It will take several minutes. Please wait.

Picture

50 Standard Standard Select
Sharpness Tint Picture Mode Colour Temp
After H the download has finished, please restart the TV.
Upgrade finished Upgrade finished Please turn off theTV!
Press D 34 button to adjust the selection item. When you are satisfied with your choice, press the E EXIT button to return to normal viewing or press MENU button to return to the previous menu.

Contrast

This will adjust the intensity of bright parts in the picture but keep the dark parts unchanged.

USING YOUR TV

How to select the TV program
A Using Program number button Enter the channel
number with the number keypad on the remote control. Using P+/P- button. B Press the P+/P- button to select a channel number.

Brightness

This will adjust the light output of the complete picture, which will mainly affect the darker areas of the picture.

Colour

This will adjust the saturation level of the colours to suit your personal preference.

Sharpness

This will adjust the sharpness of fine details in the picture.
Allows you to select the colour mix (Tint) of the picture.

How to adjust volume

Note The Tint function is only available in NTSC mode.
the desired mode by S.MODE button on the remote control.

Picture Mode

AVL (Automatic volume control)
This will reduces the differences in volume level This will select the picture mode. Select Standard/ among broadcasters. Mild/User/Vivid according to the program. You can quickly select the desired mode by P.MODE button on SRS TS XT This will control the Woofer output. the remote control. Press button to select SRS TS XT. Colour temp Press 34 button to set SRS TS XT as OFF, ON. This will increase or decrease Warm (red) and Cool Equalizer (blue) colours to suit personal preferences. This sound setting can be adjusted to suit your Select Cool to give the white colour a blue tint, personal preference. Standard to give the white colour a neutral tint, Warm to give the white colour a red tint.

ADJUSTING SOUND SETTINGS

Changing the Sound Setting
A MENU button. Press Press B button to select Sound menu, press 4
button to enter. Press C button to select the item requires adjusting.
Menu Balance Sound Mode AVL SRS TS XT Equalizer Standard Off Off

FUNCTION SETTINGS

A MENU button. Press Press B button to select Function menu, press 4 C button to select the item requires adjusting. Press D 34 button to adjust the selection item. Press When you are satisfied with your choice, press the E
EXIT button to return to normal viewing or press MENU button to return to the previous menu.

0 Select

FUCTION
Language Display Mode Blue Screen Osd Time Out Sleep Reset English Wide On 15 Secs Off Select

Text Language West

Language
To set the OSD language, press34 button to select English/Italiano/Espanol/Francais/ Deutsch/ Nederlands.

Balance

This will adjust the output of the right and left speakers to obtain the best stereo reproduction for your listening position.

Text Language

To set the Text language, press34 button to select West/East/Russian/Arabic/ Farsi.

Sound Mode

This will select the sound mode. Press 34 button to select Standard/Music/Theater/ User according to the program. You can quickly select Digital LED LCD Television Instruction Manual

Display Mode

To set the picture proportion, press34 button to select 4:3/16:9/Auto/Wide/Zoom1/Zoom2. You can quickly select the desired mode by SCREEN button on

button to enter.

the remote control.
Note The HDMI Overscan function is only available for HDMI mode.

4:3 mode

Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.

16:9 mode

Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

Channel management

Choose Wide when you want to adjust the picture in a non-linear proportion, that is, more enlarged at top sides and no alteration at bottom side.

Zoom1

Choose Zoom1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.
B 56 button to select Tuning menu, press Press
4 button to enter. Press C 56 button to select the Channel management item , and press 4 to enter.

DTV Channel Manager

Channel Edit Channel Sorting Channel Grouping Delete All Channels

Zoom2

Choose Zoom2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.

Blue Screen

This will select the character background colour. Note The Blue Screen function is only available for ATV mode.
When you are satisfied with your choice, press the D EXIT button to return to normal viewing or press MENU button to return to the previous menu.

OSD Time Out

To set how long you want the menus to appear on-screen. Each press of 34 button repeatedly to select the number of preset minutes, the Time will be set in sequence: 5secs, 10secs, 15secs, 20secs, 25secs,30secs.

Channel Edit

0023 0025

Channel name

five Ch15 QVC UK Gold bid-up.tv TCM
To set how long you want to turn off the TV after a preset time (from 5 to 240 minutes).
To control the turner , program,source volume and so on , please refer to the page 15 for detail.

Max Volume

Press 56 button to select Max Volume. Press button for adjustment between 0-100. If a certain Value is set, when volume is being adjusted, the sound value can not exceed maximum volume value. If current volume is over Max Volume, when lock set menu is set, current volume will become set maximum volume, if current volume is below maximum volume, customer set volume will stay unchanged. Rating, Press 56 button to select Parental Lock to set it
Enter Old Password Enter New Password Confirm New Password

SHORTCUT MENU DISPLAY

Subtitle Function

Channel list

Group 0023 None five Ch15 QVC UK Gold bid-up.tv
A SUBTITLE button on the remote control, Press
the Subtitle languages menu will be displayed.
Subtitle language Subtitle language

ON English

GUIDE Function
Press GUIDE button on the remote control, will display Program Guide menu, press 5634button to select the program. You can press the EXIT button to cancel the changes at anytime.
Press B 34 button to set the item ON or OFF, and press OK button to enter. You can press the EXIT button to cancel the changes at anytime.

Daily Mode

S.No Channel name five Ch15 QVC UK Gold bid-up.tv TCM

14:35-15:38 15:38-15:40

03/10/2004 15:07:09 03/10/2004 Wednesday
The Streets of San Francisco Five News Update
Note Press SUBTITLE button on the remote, it will display subtitle languages menu only in the DTV mode.

CH.LIST Function

14:35-15:38 Daily
The Streets of San Francisco Weekly Info Remider/Recorder
Press CH.LIST button on the remote control the TV will display Channel List menu. Note In TV mode, press56 button to select the channel, and Available only in the DTV mode. then press OK button to enter,then you can edit the characters of the channel. FAV Function Press FAV button on the remote control, will display Channel list Channel Frequency System Name Skip Favourite List menu. 1 49.75 DK CH-02 Off Press button to select program and press OK 2 62.25 BG CH-04 Off button to enter. You can press the EXIT button to 3 83.25 BG CC-77 Off cancel the changes at anytime. 4 144.25 DK CC-06 Off
9 152.25 184.25 220.25 471.25 487.25

Swap Insert Move

DK CC-07 DK CH-06 I CH-11 BG CH-21 DK CH-23

Copy Enter/Edit

Off Off Off Off Off

Delete

Favourite LIST
S.NO 0023 Channel five Ch15 QVC UK Gold bid-up.tv

Channel List

Channel Name Sound System Frequeny Fine Tune Skip On 5 CC-07 DK 152.25

Press INFO button on the remote control, it will display the current channel information. You can press the EXIT button to cancel the changes at anytime.
In DTV mode, press56 button to select the channel, and then press OK button to enter.

0005 five

14 35-The Streets of San Francis 15 38-Five News Update Singal 50% Quality 81%

button again.

Quick program view
This function enables quick swap to the last watched program. Press Q.view button, and the TV will be back to the TV source, expect in the USB and DVD source. Suppose the channel number you used just now A is 8 and the channel number you are using is 18 (as shown in the figure).
The sleep timer automatically shuts off the TV after a preset time (from 5 to 240 minutes). Press A the Sleep button and then the "Sleep Left Time" will be diaplayed on the screen. Press B the Sleep button again,you can set the Sleep time. When you are satisfied with your choice, press C MENU button to return to the previous menu or press the EXIT button to return to TV viewing. And the time begins to count down from the number of minutes selected.

AUDIO/I/II

Press AUDIO button on the remote control, will display Audio Languages menu. Press button to select the desired settings and press OK button to enter. You can press the EXIT button to cancel the changes at anytime.

Audio Language

B you want to return to the last watched program If
channel 8, you can simply press the Q.View button.
Stereo English English V.I.
C you want to return to channel 18, press the If
button again. Use this function, you can easily change between the channel you are using and the channel you used last Time.
Note Press AUDIO button on the remote, it will display Audio Languages menu only in the DTV mode.

04 Using the

features

Teletext functions

Teletext is an information system, broadcast by certain channels, which can be read like a newspaper. It also provides subtitles for people with hearing difficulties or those who are unfamiliar with the language in which a particular program is being broadcast (cable networks, satellite channels, etc.). Note The teletext buttons could be working even if there is no teletext signal, but there is no teletext display.

Eliminate Sound

When you need to pay attention to surrounded sounds, or there is a telephone calling you or there are some guests visiting you, the sound elimination (mute) function is very convenient.
A the MUTE button on the remote control and Press
Mute type face will display on the lower part of the screen. At this Time, the sound of the TV set is turned off. If B you want to recover the sound, press the MUTE

Teletext

To select teletext press the button on the handset. To switch off teletext, press the button again. Note all menu functions are not available in teletext mode. Only a few direct button control functions are available in teletext mode, they are: Volume adjustment Mute function
characters between Eastern and Western.
Pressing the button will stop the teletext page automa ically updating. This feature is very useful t where there are several teletext pages or data on the same page number.

Page up/down

Use the P+/P- buttons to browse next or previous page.
Pressing the button changes between full screen top half bottom half full screen. This feature is very useful as it magnifies the image making the characters easier to read.

Page number entering

To select a Teletext page, enter the page number using the numeric key pad on the remote control, or use the P+ or P- buttons, or the coloured Fast text buttons.

Reveal

Pressing the button will reveal hidden text. This feature is used to reveal information such as answers to Teletext on-line interactive puzzles.
While in normal TV mode only, pressing the button will display the teletext time in the top right hand corner for a few seconds.

Mix mode

To view the TV picture while in Text mode press the button, this will superimpose the Teletext data on top of the TV picture. Press this button again to return to Full text.
Fast text coloured buttons
Fast text automatically displays the four most commonly used pages that the broadcaster thinks that you may want to choose next. Press the same coloured button on the remote control as the coloured link at the bottom of the teletext page to go directly to that page.

Press the INDEX button to go to the index page of teletext.

Language change

Pressing the button will change the Teletext

Subcode

Pressing the button by entering its 4-digit number to enter a secondary page.

may be unsmooth.

Playing Pictures

USB MODE

Note The diagrams in the following section are schematic and only for your reference. Please see the actual product if necessary.
A entering USB main interface, press yellow After
button to select PHOTO item. Press B OK to confirm the selection and enter the picture file list,and the TV will prompt us to set the background music. You can set the background music as you need.

USB Devices

Connect the USB device to the USB IN jack on the side of TV (or on the back of TV).
Recorder Do you want to select background music? YES NO

Move Music

Press C 5/6 and 4 / 3 to select the picture you want to play, press OK to play the pictures.

To use the USB device

A Supported file formats:
Photo: *.jpg; Music: *.mp3 files; Movie: *.avi files; Note Due to the particularity of file cording, some files may be unable to read. Supported equipment: B Support the equipment that supports Mass Storage Protocol , such as some USB disks, mobile harddisks. If USB equipment could not be identified due to unsupported file system, please format the equipment to the FAT32. To C achieve smooth playing, ensure the following: The file code rate should be lower than 300KB/S; Due to the limitation of USB signal transmission distance, it is recommended not to use USB patch cord, in case of using the cord, make sure that its length is not over 1m; Use high-speed USB equipment in conformity with USB2.0 full speed Interface Standard; If USB equipment in conformity with USB1.1 full speed Interface Standard is used, the playing
DIf you want to pause the picture which is being
palyed, press the PALY/PAUSE button again. Press ZOOM to magnify the picture. Press PREV/ NEXT to select the last or next picture. Press 3/4 and 5/6 to rotate the picture. To E exit playing, just press BACK repeatedly. Note The menu display varies with the photo name and pixel in your equipment.

Playing Music

A entering USB main interface, press green After
button to select MUSIC. Press B OK to confirm the selection and enter the music file list.

0001 C:

C 5/6 button to select the music you want to Press
play, then press PLAY/PAUSE button to play the Digital LED LCD Television Instruction Manual
music. Press / to achieve the REV (fast back) and FWD (fast forward) of the music being played. Press PREV/NEXT to select the last or next music. To D return to the main menu, just press BACK repeatedly. Note You can enjoy the music and the picture at the same time.
The device reports the unfaithful size.

Time shift

Timeshifting Pause II

Playing a Movie

A entering USB main interface, press 3/4 to Atter
select Movie. Press B OK to confirm the selection and enter the movie file list.

Timeshifting

Message Do you want to stop TIMESHIFT? YES OK
Time Shift function is only available in DTV mode. Press PLAY/PAUSE to prepare and then the TV begin timeshifting. If you want to stop time shift function, press the STOP button.

Move Select

Music Photo
Press / to achieve the REV (fast back) and FWD (fast forward) of the time shift program. Press PLAY/PAUSE to pause timeshifting. You can stop the time shift program being played by pressing the STOP button.
C / button to select the movie you want to Press
play, and then press PLAY/PAUSE button to play the movie. Press PREV/NEXT to select the last or next movie. To D exit playing, just press BACK repeatedly.

Recording

A D.MENU button to record the program being Press

played.

Using External USB Disk For Recording
A Insert the USB device with FAT32 format into the
USB connector. Waiting for the system checking. And you can see B the speed data after the success checking. Note The system can not work normally if the USB device have the listing problem below: The device has bug. The device has error block.
Press B STOP button to stop the program recording being played.
Message Do you want to stop RECORDING? YES OK
C Playback the recorded program. Press INDEX For

button to open the recorded list.
Recorder Recorded List Select Disk Reminder Select: OK or -->
Changing the channel will not influence the recording in the same frequency, but will influence the time shift. When the recorded program is being played, you can not delete it.

Reference

sections
Press 56 button to select the content you recorded. Press the 4 button to display the program To assist in location of possible faults use the information. help guide below: Recorded list
QVC(000101_022255).mpg) five(040310_145012).mpg)

Troubleshooting

Duration 00:00:13 (3MB)

DELETE

No picture, no sound
Press red button to cancel. Press OK or PLAY/PAUSE button to play the program recorded and press STOP button to stop it.

Select Disk

Verify if the television is properly plugged in. Verify if the television has a proper supplied power source. Verify if electricity is available. Verify if correct signals are input. Operate the remote to change signal input to correct input. Restart the television if power supply is interrupted. Press MUTE button and verify if Mute mode is set. Switch to other channel and verify if the same problem happens. Press VOL+ button to see if the problem can be solved. Verify if sound system is correct. Refer to users manual for adjustment. Verify if correct channel is selected. Adjust the antenna. Verify if the same problem exists in other channels. Check out of picture and sound systems. Refer to relative instructions in the Manual for color adjustment.

Blank screen

No sound
D 56 button to select the Select Disk. Press
Press the 4 button to enter,then press 56 button to select the device.

Reminder/Recorder

Timer NO Mode Program Data Time Duration 1 Off

Poor sound

Wakeup Mode
five 03/10/2004 14:5 00:00

Recorder

No picture in some channel
Press E 56 button to select the Reminder. Press the 4 button to enter , then set the appointment of recording. Note
No color for some channel program (black and white)
Spots with some or all pictures
Verify if the antenna is correctly connected. Verify if the antenna is in good condition. Make fine adjustment of channel. Disconnect the television from power supply and 10 seconds later, connect the television to the power supply. If the problem still exists, contact authorized after-sales service for technical assistance.

Accessory

User manual Remote control Battery (2)
Television out of control
* he part specifications of this TV set provided here T are for reference only. Differences may occur as product technology is updated. Design and specifications are subject to change without notice.

Note If the fault can not be repaired using the above guide consult with your local authorized service centre. The TV set must only be repaired by a qualified registered service person. Never attempt to remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.

Specification

Colour system
PAL, SECAM, NTSC (AV) BG, DK, I, L,L' SCART, YPb/Pr, YCb/Cr, AV, VGA, HDMI, USB Composite: 480i/p, 576i, 720p, 1080i, 1080p See rating plate See rating plate

2.5W+2.5W

Sound system Video input DTV Y/Pb/Pr Power Power consumption

Audio output

Environment conditions
Working temperature: +5 C - +35 C Working humidity: 20% - 80% Storage temperature: -15 C - +45 C Storage humidity: 5% - 90%

0090509580C