104801man_de_en_fr_es_nl.indd 10

g User manual

BEFORE OPERATING THIS HEADSET FOR THE FIRST TIME The device must be charged for approx. 4 hours, uninterrupted, until the indicator light goes out. See "Charging the BLUETREK TATTOO" in the instructions. Pair the headset with a mobile phone. See "Pairing the BLUETREK TATTOO" in these instructions. INTRODUCTION The BLUETREK TATTOO headset is a wireless headset for mobile phones with Bluetooth technology. The BLUETREK TATTOO is a Bluetooth-enabled headset that fulls the conditions as required by Bluetooth 2.0 protocol. Two proles are supported: Headset proles and devices equipped with "Hands-free" proles. The BLUETREK TATTOO headset has 2 buttons: "TALK" button (main button) "VOL+/- " button Charging socket
Removeable earband TALK VOL+/-
Indicator light Replaceable "skin"

Microphone 11

104801man_de_en_fr_es_nl.indd 11
Charging the BLUETREK TATTOO Connect the charger to the headset and the mains. During charging, the indicator light ashes red. As soon as the charging process is over, the indicator light goes out. Each subsequent charging cycle lasts approx. 3 hours. When you hear a low-pitched beep in your headset and the indicator light ashes red, the headset must be recharged. Important: When the headset is fully charged, the red indicator light does not illuminate when the device is connected to the charger. (To check whether the headset is fully charged, press the TALK button for approx. 2 seconds. When you release the button, the red indicator light illuminates for approx. 3 seconds.) The headset cannot be used while it is charging. To maintain the battery capacity for as long as possible, we recommend fully charging the headset only when the battery is low. This way, the battery can be maintained for approx. 500 charging cycles. If the battery has been dead for a long period of time, the battery may be fully discharged. In this case, charge the battery for 3 hours or longer, until the battery is fully recharged. If you are charging the battery for the rst time after a long period of storage, it can take several minutes for the red indicator light to illuminate. Do not charge the headset for longer than 10 hours. Use of a different charger voids the warranty. To do so is expressly prohibited and extremely dangerous.
104801man_de_en_fr_es_nl.indd 12
Pairing the BLUETREK TATTOO Before using the BLUETREK TATTOO headset for the rst time, you must pair the headset with your Bluetooth-enabled mobile phone. "Pairing" means setting up a wireless connection between two Bluetooth-enabled devices so that these devices can communicate with one another. Preparing to pair the devices: 1. Place the BLUETREK TATTOO and the mobile phone at a distance of 30 cm from one another. 2. Switch on the mobile phone and select Bluetooth detection mode (see the instructions for your Bluetooth mobile phone).

3. With the BLUETREK TATTOO switched off, press and hold the TALK button for about 7 seconds until the green and red lights ash alternately. A tone is heard over the speaker.
104801man_de_en_fr_es_nl.indd 13
4. Follow the steps in the instructions of your mobile phone to accept the pairing. The PIN code (or passkey) for the BLUETREK TATTOO is 0000. After entering the PIN, press "Yes" or "OK".
5. With most phones, you must then select the "Connect" function. Once the connection has been established, the indicator light illuminates green and begins to ash slowly. If discover mode is not activated within 5 minutes, the headset switches off automatically. The headset must be switched back on and the pairing must be reinitiated. 14
104801man_de_en_fr_es_nl.indd 14
Switching the BLUETREK TATTOO ON and OFF Switching the BLUETREK TATTOO ON With the BLUETREK TATTOO switched off, press and hold the TALK button for 3 seconds until the green indicator light is on. A beeping sound (2 tones) is heard in the speaker. Then release the TALK button. Switching the BLUETREK TATTOO OFF With the headset switched on, press and hold the TALK button for 7 seconds until the red indicator light is on. A beeping sound (2 tones) is heard in the speaker. Then release the TALK button. Making a call Mobile phones with voice dialling Make sure that the voice dialling function on the mobile phone is activated and that the necessary voice tags are saved in the phone. To enter these voice tags, see the information in the operating instructions of your mobile phone. If there is no call in progress and no incoming call, press the TALK button. Wait until the audio signal is sent by the mobile phone (normally a short tone). Say the name of the person whom you wish to call (voice tag).
104801man_de_en_fr_es_nl.indd 15
Mobile phones without voice dialling Make sure that the headset and the mobile phone are switched on and in standby mode. Dial the number on the mobile phone; after about 2 seconds, the audio connection is established. This function does not work on all mobile phones. For more information, see our website: www.bluetrek.com for information on troubleshooting. Accepting a call When the headset rings, press the TALK button to accept the call. Ending a call Press the TALK button once to end the call. Setting the volume To increase the volume during a call, press the VOL+ button on the headset. To decrease the volume during a call, press the VOL- button on the headset. Muting the microphone Muting the microphone during a call During a call, press and hold the VOL+ button for approx. 2 seconds. A periodic tone is heard in the speaker when the microphone is muted.

104801man_de_en_fr_es_nl.indd 16
Turning mute off When the microphone is muted, briey press the VOL+ button on the BLUETREK TATTOO. The periodic tone can no longer be heard. Fitting the Ergobud* The package includes 3 differing sizes of Ergobud*. For your personal comfort, you can change the position of the Ergobud*.
To replace the Ergobud*, carefully remove the cover from the speaker by pulling it off.
Place the new Ergobud* onto the speaker. Start with the bottom of the speaker.
*Registered trademark pending
104801man_de_en_fr_es_nl.indd 17
Replacing the "skin" To attach a new "skin", take hold of the old "skin" at the edge and pull it off as shown in the illustration.
Stick the new "skin" onto the headset as shown in the illustration. Press the "skin" down to ensure that it adheres rmly.
Call waiting If you hear the call waiting signal tone during your call, press the TALK button for approx. 3 seconds to accept the second call and place the active call on hold. Press the TALK button for approx. 3 seconds to switch between the active call and the second call. To end a call and accept the second call, press the TALK button once. Under some circumstances, this function may not be available on your mobile phone. You can accept the second call at any time using the keypad of your mobile phone.
104801man_de_en_fr_es_nl.indd 18
Additional functions for some mobile phones Rejecting a call When the headset rings, press and hold the TALK button for approx. 2 seconds. Redialling the last number If there is no incoming call and no call currently in progress, press and hold the TALK button for approx. 2 seconds until a beeping sound is heard. g Registration and Safety Certi cation/General Information This device bears the CE symbol as specied by the provisions of Directive R & TTE (1999/5/EC). Hama GmbH & Co. KG hereby declares that this device is in compliance with the basic requirements and other relevant guidelines and regulations of the 1999/5/EC guideline. You will nd the declaration of compliance and declaration of conformity in the Internet at http://www.hama.com
104801man_de_en_fr_es_nl.indd 19

104801man_DE_EN_FR_ES_NL_Quickstart.indd 9
Hama GmbH & Co KG D-86651 Monheim/Germany www.hama.com
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.
104801man_DE_EN_FR_ES_NL_Quickstart.indd 10

00104801/01.10