After Media Center returns with the Youre Done! message, your WinTV-PVR will have been set up by Media Center Edition. Now, you need to set up the Electronic Program Guide. Media Center should automatically launch the Guide set up. You will see a message: Set Up Your Program Guide. Click Next. Chose your region and the wizard will move you toward the completion of the Program Guide set up.

WinTV-PVR-USB2 MCE

Personal Video Recorder
If you cannot find the Radio button in Media Center
If you install the WinTV-PVR with FM radio, but the Radio button does not appear on the Start menu, Media Center might not have detected the added tuner yet. Go to Radio Settings to initiate a check for an available FM radio-enabled tuner. To go to Radio Settings: 1. 2. 3. Press the START button on the remote, and then select Settings. Select Radio. Media Center will check for a tuner that supports FM radio. One of the following may occur: - You will be notified if Media Center is unable to detect a tuner that supports FM radio. Try enabling the tuner again. - Media Center detects the tuner and the FM Radio Presets page appears. However, if the Radio button still does not appear on the Start menu, you may need to turn on Radio in Set Program Access and Defaults (see below). To turn on FM radio in Set Program Access and Defaults: 1. 2. 3. 4. Close Media Center. Click the Start button on the taskbar, point to All Programs, and then click Set Program Access and Defaults. Select Custom. Click the down arrow button to expand the option. Under Choose a default media player, select the check box next to Media Center Radio. Click the button Enable access to this program for Media Center Radio. When the box is selected, Radio will appear on the Media Center Start menu; when the box is cleared, Radio will not appear.
Quick Installation Guide for Windows XP Media Center Edition 2005
Hauppauge Computer Works, Inc. 2004, 2005
Hauppauge Computer Works, Inc. 91 Cabot Court Hauppauge, NY 11788 Telephone: 631-434-1600 Fax: 631-434-3198 Tech Support: 631-434-3197 techsupport@hauppauge.com Telephone: 02161-694880 Fax: 02161-6948815 Tech Support: 02161-6948840 info@hauppauge.de Telephone: 0207-378-1997 Fax: 0207-357-9171 Tech Support: 0207-378-0202 support@hauppauge.co.uk
Hauppauge Computer Works, GmbH Krefelder Strae Mnchengladbach, Germany
Hauppauge Computer Works, Ltd 6-10 Bank Chambers Borough High Street London, U.K. SE1 9QQ

www.hauppauge.com

Included with WinTV-PVR-USB2 MCE:
WinTV-PVR-USB2 box, with 125 channel cable ready TV tuner, FM radio receiver, MPEG-2 hardware audio/video compressor FM radio antenna Wall mounted power supply WinTV-PVR MCE Driver Installation CD-ROM with drivers for Windows XP Media Center Edition 2005 WinTV-PVR-USB2 MCE Quick Installation Guide (this guide) Remote control transmitter with batteries (some models) Remote control receiver (USB) with IR blaster for controlling external set top boxes (some models)
QI-MCE-V3.2-ENG 4 June. 31, 2005
Installing the WinTV-PVR-USB2 MCE
The WinTV-PVR-USB2 MCE is an external USB2.0 device with a built-in TV tuner plus FM radio and hardware MPEG encoder. The WinTV-PVR-USB2 MCE differs from the retail WinTV-PVR-USB2 version in that the MCE version does not include a built-in remote control receiver since Media Center requires its own unique USB connected remote control device. To sucessfully configure a Windows XP Media Center 2005 system with TV and remote control, you will need to install the Hauppauge WinTV-PVR-USB2 and a Media Center remote control transmitter and receiver (included in some models).
Step 2: Boot your PC. Step 3: Plug the power supply into WinTV-PVR-USB2
Plug the supplied Power Supply into the Power Supply input on WinTV-PVRUSB2.
ote: DO NOT PLUG THE POWER INTO WINTV-PVR-USB2 UNTIL YOUR PC HAS COMPLETELY BOOTED!
Step 4: Installing the WinTV-PVR-USB2 MCE driver

Installation overview

To install WinTV-PVR-USB2 MCE, you will follow these steps: Step 1. Connect the TV antenna, FM radio antenna (optional) to WinTV-PVR-USB2. Connect the USB cable to the WinTV-PVRUSB2 and to a USB port on your PC. Step 2. Boot your PC. Step 3. After Windows is running, plug the supplied Power Supply into WinTV-PVR-USB2s power input. Step 4. After plugging in the power to WinTV-PVR-USB2, the Found New Hardware Wizard will then load the WinTV-PVR-USB2 driver from the WinTV MCE Installation CD-ROM.

After plugging the power to your WinTV-PVR-USB2, the Found New Hardware Wizard will appear. Insert the WinTV-PVR MCE Driver Installation CD-ROM in your PCs CD-ROM drive and make sure Install the software automatically (Recommended) is checked. Click Next. The WinTV-PVR-USB2 drivers will automatically install. This will take a minute or two. Click Finish.
Removing the WinTV-PVR driver
Step 1: Connect the WinTV-PVR-USB2 cables
Plug your TV antenna or cable TV cable into the WinTV-PVR-usbs TV Connector. If you would like to use FM radio, plug the supplied Radio aerial into the FM radio connector. This may not be necessary if your TV aerial or cable network supplies FM, or if you do not want to listen to radio with Media Center. The S-Video and Composite video inputs and the Left & Right Audio Inputs can be used to bring audio/video from a VCR, camcorder, DVD player or satellite receiver. Plug one end (the square end) of the supplied USB cable in the WinTVPVR-USB2s USB Cable connector.
FM radio antenna connector Left &Right Audio Inputs Composite video input S-Video input
If you ever need to remove the WinTV driver, run HCWClear.EXE from the WinTV-PVR MCE Installation CD-ROM.
WinTV-PVR-USB2 setup under Media Center Edition 2005
If you are using the WinTV-PVR under Windows XP Media Center Edition 2005, you should run the TV Setup Wizard in Media Center. Normally, the next time you run Media Center after the installation of a new TV tuner, the Setup Wizard will run. This might not happen if you had previously installed a different TV tuner board or USB device. To manually launch the TV Set Up Wizard, in the main Media Center menu go to Settings / TV / Set up TV Signal. You will see a message: Set Up Your TV Signal. Click Next. You will then see Chose your Region, select your region and click Next.
TV Connector for antenna or Cable TV

USB Cable Connector

Power Supply input
If you are using WinTV-PVR-USB2 for receiving analog TV, you will see the message Select cable, satellite, Antenna or no signal at this time. Chose one and click Next. You will then be asked if you have a Set top box? Chose yes or no. Click Next.

ote: at this point, Media Center Edition will set up the TV tuner. This might

take a minute or so.

After determining the type of signal, Media Center displays a message You are Done! Now, you need to set up the Electronic Program Guide. You will see a message: Set Up Your Program Guide. Click Next. The Program Guide Set Up Wizard will move you through the completion of the Program Guide set up. When you are finished with the Program Guide Setup, you can start watching TV under Media Center! Just click the MyTV button on your Media Center remote control.
WinTV-PVR for Media Center Edition Quick Installation Guide
WinTV-PVR-150 MCE Kit WinTV-PVR-500 MCE Kit
Hauppauge Computer Works, Inc. 2005

Troubleshooting

Removing the WinTV-PVR driver If you ever need to remove the WinTV-PVR driver, run HCWClear.EXE from the WinTV-PVR MCE Driver Installation CD-ROM. If you cannot find the Radio button in Media Center If you install the WinTV-PVR-USB2 MCe or WinTV-PVR-500 MCE with FM radio, but the Radio button does not appear on the Start menu, Media Center might not have detected the added tuner yet. Go to Radio Settings to initiate a check for an available FM radio-enabled tuner. To go to Radio Settings: 1. 2. 3. Press the START button on the remote, and then select Settings. Select Radio. Media Center will check for a tuner that supports FM radio. One of the following may occur: - You will be notified if Media Center is unable to detect a tuner that supports FM radio. Try enabling the tuner again. - Media Center detects the tuner and the FM Radio Presets page appears. However, if the Radio button still does not appear on the Start menu, you may need to turn on Radio in Set Program Access and Defaults (see below). To turn on FM radio in Set Program Access and Defaults: 1. 2. 3. 4. Close Media Center. Click the Start button on the taskbar, point to All Programs, and then click Set Program Access and Defaults. Select Custom. Click the down arrow button to expand the option. Under Choose a default media player, select the check box next to Media Center Radio. Click the button Enable access to this program for Media Center Radio. When the box is selected, Radio will appear on the Media Center Start menu; Radio will not appear if unchecked.
Hauppauge Computer Works, Inc. 91 Cabot Court Hauppauge, NY 11788 Hauppauge Computer Works, GmbH Krefelder Strae Mnchengladbach, Germany Hauppauge Computer Works, Ltd 6-10 Bank Chambers Borough High Street London, U.K. SE1 9QQ
Telephone: 631-434-1600 Tech Support: 631-434-3197 techsupport@hauppauge.com Telephone: 02161-694880 Tech Support: 02161-6948840 info@hauppauge.de Telephone: 0207-378-1997 Fax: 0207-357-9171 Tech Support: 0207-378-0202 support@hauppauge.co.uk

www.hauppauge.com

Included with the WinTV-PVR-150/500 MCE Kits: WinTV-PVR-150 MCE PCI board, with 125 channel cable ready TV tuner, MPEG-2 hardware audio/video compressor. The WinTV-PVR-500 MCE PCI board comes with dual 125 channel cable ready TV tuners and dual hardware MPEG encoders plus one FM radio receiver. WinTV-PVR MCE Driver Installation CD-ROM WinTV for Media Center Quick Installation Guide (this guide) Media Center Remote control transmitter and two AA batteries Media Center USB remote control receiver IR transmitter cable
QI-PVR150MCE-V3.4-ENG August 7, 2005
Installing the WinTV-PVR-150/500 Kit for Media Center Edition
The WinTV-PVR for Media Center boards differ from the non-MCE WinTV-PVR versions in that they use the Microsoft Media Center USB Remote control and IR transmitter instead of the WinTV-PVRs built-in IR receiver transmitter.

/500MCE via the white and red audio input jacks. Step 2: Installing the WinTV-PVR-150/500 Media Center driver After installing the WinTV-PVR in your PC, boot Windows. The Found New Hardware Wizard will appear. Insert the WinTV-PVR MCE Driver Installation CD-ROM in your PCs CD-ROM drive. Click No, not at this time. Click Next. Make sure Install the software automatically (Recommended) is checked. Click Next. If the Hardware Installation dialog box opens, click Continue Anyway. Click Finish. If you are installing the dual tuner WinTV-PVR-500MCE, you will see the Found New Hardware message for the second TV tuner. Follow these steps for the second TV tuner. Step 3. Install the Media Center Remote control The Media Center remote control receiver is a USB device which both receives remote control commands and also transmits commands via an IR Blaster to a set top box to change channels. To install the Media Center remote control, simply plug it into any USB port. To test the Media Center remote, click the Start button in the middle of the remote control. Media Center should open. If you have a satellite set top box and would like the Media Center remote control receiver to change channels, plug one end of the IR Blaster cable into the Media Center remote control receiver and position the other end (the transmitter end) over the IR receiver on your set top box.

Installation overview

Step 1. Install the WinTV-PVR in your PC and connect the TV and A/V cables. Step 2. After starting WindowsXP install the WinTV-PVR device driver from , the WinTV MCE Driver Installation CD-ROM. Step 3. Install the Media Center remote control.
Detailed installation instructions
Step 1: Install the WinTV-PVR-150/500 board in your Media Center PC and connect the cables Turn the power off on your PC. Install the WinTV-PVR into a PCI slot. On some PCs, the WinTV-PVR needs to be plugged into the first or second PCI slot. Plug your TV antenna or cable TV cable into the TV Connector. Audio and video from an external A/V device (satellite TV receiver, cable TV box, VCR, camcorder, camera, DVD player) can be brought into the WinTV-PVR via the back panel connectors. If your A/V device uses S-Video, connect to the S-Video input on the WinTV-PVR-150/500MCE. If your video device uses composite video instead of S-Video, use the yellow RCA jack. Audio input from an external A/V device can be brought into the WinTV-PVR-150

WinTV-PVR-150 WinTV-PVR-500 Board connectors
FM Radio Connector input (WinTV-PVR-500 only) TV Connector for antenna or Cable TV input S-Video input
TV set up under Media Center Edition
To manually launch Media Centers TV Set Up Wizard, in the main Media Center menu go to Settings / TV / Set up TV Signal. You will see a message: Set Up Your TV Signal. Click Next. In Confirm your Region, make sure your region is selected. Click Next. You will see Automatic TV Signal Setup. We recommend selecting Configure my TV signal automatically. Click Next.
Composite video input connector
Left audio input Right audio input
ote: at this point, Media Center Edition will set up the TV tuner. This might

take a minute or so.

You will then see a message saying Examining your TV signal. Media Center is determining the type of TV connection you have. When it is finished, it will tell you whether you have a cable TV, antenna or set top box connection.