Congratulations on purchasing Hawkings HWPS12UG 1-Port Parallel + 2 USB Ports Wireless G Print Server. The Hawking HWPS12UG is a powerful and convenient network printing solution that will connect your USB and parallel printers to your network. The HWPS12UG has a 10/100Mbps auto-sensing port, allowing you to attach it to a 10Base-T or 100Base-TX network without the need for a dedicated PC print server. The HWPS12UG also supports multiple servers and multiple protocols, providing you with the capability to print from anywhere, from any computer and from any application.

1. 2. 3.

Connect the HWPS12UG Print Server to a network. Connect the HWPS12UG Print Server to your printer(s). Plug the AC power adapter into the power slot on the side of the Print Server. Check the LEDs marked as Power, LAN, and WLAN on the front of the Print Server. They should start to flash while doing a routine diagnostic test and printer check. If not, please contact your local dealer for repair or replacement.
You must use the power adapter shipped along with the print server. sources. Do NOT use any other power adapter from other
Please note that your HWPS12UG hardware is automatically set to a factory default IP address of 192.168.1.250
LED Indicators The HWPS12UG is equipped with LED lights to assist in diagnosing print server or network errors. Power This light will illuminate when the HWPS12UG has sufficient power and the power adapter is plugged into the HWPS12UG. When the print server unit is powered on, the Power LED along with either the LAN LED or the WLAN LED will flash as part of the units Power On Self Test (POST). This indicates that the print server hardware is properly configured. The HWPS12UG may take up to 1 minute to perform its internal diagnostic tests. LAN This light will illuminate and flash when the HWPS12UG detects 10M or 100M data transmissions over the network. Printer Port 1, 2, or 3 (P1, U2, U3) This set of lights will illuminate and flash when the HWPS12UG detects a printer attached to any of the 3 printer ports. Please note port number from the back panel of the HWPS12UG. Wireless The wireless light indicates that the HWPS12UG is sending and receiving wireless information. wireless mode is enabled.
Please note that the Reset button is located on the back of the HWPS12UG. Hold this button down for more then 5 seconds to reset the print server into factory default mode.
When the wireless light is flashing,
WINDOWS 95/98/ME/NT/2000/XP 1) POWER ON: After you have correctly connected your print server to your PC and router, please power on all units. 2) Before the installation, please verify that your network protocols are installed on your PC (TCP/IP, IPX and/or NetBEUI). If they are not installed, please consult your operating systems manual for instructions on how to do so. 3) INSTALL the Administrator Installation Program: To install your Print Server administration software, please follow the directions listed below. 1. Insert the Windows 95/98/ME/NT/2000/XP Setup CD into your CD-ROM.
(Windows should execute the Autorun.exe program automatically. If not, run Autorun.exe manually from your CD-ROM drives root directory.)
2. The Hawking Installation Windows manager will pop up on your screen as follows:
Click on Admin Installation and the Utilities Setup window will be displayed.
Click Next, and specify the destination folder where the HWPS12UG utility files will be installed.
Click Next, and select the components you want to install. It is highly recommended to install all provided components.
Click Next, and specify the program folder where the program icons will be added.
Click Next to start the utility file installation.
The Print Server Utilities program will finish installing. Click Next, and the
After this installation is complete, the next step will involve configuring your HWPS12UG. Choose Print Server dialog box will be displayed as follows.
Click Next and a dialog box will prompt you to name your print server. Naming your print server is optional. (Please make sure to write down the name you assign to your print server or the pre-generated print server name for future use.)
Click Next to configure your print servers network communication protocol.
With the TCP/IP protocol, you can either (1) assign a dedicated IP address for your print server or (2) configure it later through the configuration utility software. (If you choose Do not change IP configure later, there is no effect on your network settings. networks). 11. Click Next and the configuration summary will be displayed in the setup window. You have completed the Print Server Setup process and are ready to set up your print server to work with your printer. Please click Next and your system will add the HWPS12UGs network port to your PC. This is suitable for both Non-IP and IP-enabled

12. The Installation complete window will be displayed to indicate that the Administrator Installation procedure is completed.
(Please restart your computer for your setup to complete its installation.) Once your computer is restarted, please open your START menu and select the newly installed Printserver Configuration program in the Printserver Uilities folder.
Print Server Configuration Utility
Once started, the Print Server Manager program will search your network for any attached HWPS12UG print server. Please highlight the desired print server and click the setup Wizard icon located on the tool bar to configure your HWPS12UG. Double click on the Print Server Wizard and a window will pop up requesting a user name and password. Password: 1234 Click on the Print Server Wizard again and the setup wizard will guide you through the setup process. Please use User Name: admin and
Step 1: In this step, you can setup the name of the print server, the SMB group name, and the name of each printer port. You can also choose whether to enable/disable the wireless functionality of this print server.
Please note: By keeping the wireless function setting on AUTO you will need to unplug your Ethernet cable and power cable once configuration settings are saved and your print server is rebooted. Re-insert your power cable to boot the print server into Wireless Mode.
complete) (Please only perform this step after the configuration process is
Step 2: Select to enable or disable your networking and printing protocols. We suggest enabling all protocols for full print server functionality.
Step 3: Set the IP address of the HWPS12UG.

You may

specify a static IP address or use Auto to obtain an IP address from your routers DHCP server. (It is recommended to use auto if you are unsure about your network IP address) Please set the print servers subnet mask (typically 255.255.255.0) and the intended gateway.
Please Note: Your gateway is most likely your routers IP address.
Step 4: Set up NetWare printing if desired.

are not using Netware).

(You may skip setup if you
Please refer to the manual for more detailed
installation information.
Step 5: Set up AppleTalk printing if desired. Please refer to the manual for more detailed installation information.
Step 6: Select the Wireless Adapter mode to set up your wireless LAN settings. For instructions on setting up the HWPS12UG in Ad-Hoc mode, please refer to the manual for more detailed installation information.
To connect to a previously configured wireless network access point or wireless router, please select Infrastructure Mode and press Next.
Step 7: Select to scan your network for your wireless access point or router. (If you already know your router or access points SSID, you can choose to manually input it here).
Step 8: Select your access point or router from the available wireless client list by highlighting the SSID and pressing Next. (If your router or access point SSID is not visible, please hit the scan button again. If the SSID of your access point or router is still not displayed in the window, please check your wireless router or access point settings to make sure it is set to broadcast its SSID).

Step 9: If your wireless router or access point has WEP active, please change the settings for the print server to correspond with your router or access points current WEP settings.
Step 10: Click Set to finalize your settings.
NOTE: If using the AUTO Wireless setting, please unplug your Ethernet cable and power cable once configuration settings are saved. Re-insert your power cable to boot the print server into Wireless Mode. For web configuration and advanced configuration options, please refer to your HWPS1UG manual which is located on the HWPS12UG Installation CD-ROM.
Now that you have completed the administrators setup, you can perform the Client Installation procedure on all client computers in your network. To set up printing from this administrators PC to the print server, please follow the standard Add Printer procedure as described in the steps below. Please choose your appropriate operating system and follow the directions to add your printer through your OS.
(Repeat the add printer steps for each printer installed on the

HWPS12UG).

WINDOWS XP Setup Step1. Click the Start button; choose Control Panel
Printers and Faxes Step2. Click on Add a Printer
Step3. The Add Printer Wizard will appear Next.

Step4.

Select Local printer attached to this Press Next.

computer

Step5. In the Select a Printer Port window select Use the following port and drag the selection bar down to your newly created print server entry Next. Press
Step6. Select a suitable printer manufacturer and model, and then click Next.
Step7. Please continue through the next couple of installation steps by pressing Next until your new printer is added to your computer. Press the finish button to finalize your configuration. (Repeat the add printer steps for
each printer installed on the HWPS12UG).
WINDOWS 98/NT/ME/2000 Step1. Click the Start button, choose Setting Printers Step2. Double click on Add Printer
Step3. Select Local printer Next.
Step4. Select your printer manufacturer and model, and then click Next.
Step5. Choose the Print Servers Network Port, which was created by the administrator or client installation process, and click Next.
Step6. Complete the rest of the questions to finish the network printer setup. (Repeat the add printer steps for each printer installed on the

Client Installation

1. Insert the CD shipped along with the HWPS12UG into your CD-ROM drive. The Autorun.exe program will execute automatically. If it does not start automatically, run Autorun.exe manually from your CD-ROM drives root directory. 2. The "Installation Manager" will be displayed on the screen as follows.
3. Click Client Installation and the Utilities Setup window will be displayed.
4. Click Next and specify the destination folder where the utilities will be installed.

5. Click Next and specify the program folder where the program icons will be added.
6. Click Next to start the installation.
7. You have completed the software installation process. Click Continue and the HWPS12UGs network port will be detected on the network and will be added to your PC.
8. The Installation complete window will be displayed to indicate that the Client Installation procedure is finished.
You must then perform the Windows standard Add Printer procedure, as described below, to add a network printer to your PC. Step1. Click the Start button, choose Setting Printers Step2. Double click the Add New Printer Local printer click Next. select
Step3. Select a suitable printer manufacturer and
model, and then click Next. Step4. Choose the HWPS12UGs Network Port that was created in the client installation process and click Next. Step5. Complete the rest of the questions by hitting Next to finish the network printer setup.

(Repeat

the add printer steps for each printer installed on the

IPP Printing

The IPP (Internet Printing Protocol) provides you with a convenient method for remote printing jobs via the TCP/IP protocol. The HWPS12UG 10/100M 2 USB Ports + 1-port Parallel Wireless G Print Server can support IPP printing capabilities. It is not necessary to modify any of the print servers internal settings to use the IPP printing features. Windows 2000 and Windows XP computers can use IPP printing functions through the operating systems internal IPP functionality. IPP printing will let you share your network printer with any PC that can access the HWPS12UG print server by IP. You can even share your printer with users over the Internet who know your printer model, printer port, and the IP address of your HWPS12UG.

IPP Setup

Print Server Side It is not necessary to modify your IPP settings on the print server side. Make sure you know your print servers IPP settings and make sure they are correctly set to your networks IP settings. Contact your system administrator if you are unfamiliar with your networks routed IP settings. If you would like to share your printer with Internet users outside of your internal network structure, you will have to set an outside IP address that can access the print server. You also have to make sure that any gateway, router or firewall does not block the IPP

protocol if you have those devices installed. Please contact your system administrator or consult your routers manual for DMZ or port mapping configuration settings. Client Side You will need to perform Windows standard Add New Printer procedure. To do this, select the Network Printer setting as shown in the screen below and click Next.
Select Connect to a printer on the Internet or on a home or office network and enter the URL of your HWPS12UG print server. The URL format will be http://IP:631/LPT_PORT. The IP portion of the URL will be the print servers IP address. You will need to write down 631 after the IP address. 631 is the IPP standard port number for IPP printing requests. LPT_PORT is the port name of your print server that your printer is connected to. For one port print servers, the 37
port name will be lpt1. For Hawkings HWPS12UG three-port print server, the port names are lpt1, lpt2 or lpt3 depending on which printer port your printers are connected to. (Please write down the printer port and corresponding printer model for configuring our line of multiple port print servers.) An example IP address will be modeled as follows: The URL will be http://192.168.2.1:631/lpt1 for a print server located on the first printer port (lpt1) of the IP address 192.168.2.1. After entering the URL of print server, click Next and complete the remaining configuration settings to access the shared network printer.
For advanced configuration options, please refer to your HWPS12UG manual which is located on the HWPS12UG Installation CD-ROM.
Ethernet A networking standard using cables (Category 5) to create a network. IPP Internet Printing Protocol. IPP allows you to print your documents over an Internet connection to another printer over the net. Network Adapter Also known as a NIC (Network Interface Card). Used to provide PCs or laptops with an Ethernet port or wireless access to the network. SSID (Service Set Identifier) Also referred to as the wireless network name. This is the call tag used to identify a wireless network. Please make sure the SSID of your print server is the same as the SSID of your current wireless network. Router A device used to share Internet access from one user to multiple users.

2 US B + 1 Pa r a l l e l W i r e l e s s G Pr i n t S e r v e r
CO N N E CT W H E R E V E R Y O U W A N T W H E N E V E R Y O U W A N T

C A R E F R E E

W IR E LE SS

HW PS12UG

Print Server
Wireless 802.11G 2 USB + 1 Parallel Port
PACKAGE CONTENTS: One Wireless Print Server One CD Software Utility Power Adapter Easy-to-follow Quick Installation Guide
Print over the Internet/Intranet to your home or office networked printer! The Hawking HWPS12UG Wireless 802.11g 2 USB + 1 Parallel port 10/100M Internet Print Server is a powerful and convenient tool to connect your USB and parallel printers to a 10/100M or wireless 802.11b or 802.11g Network. Through its enhanced functionality, the HWPS12UG can support up to three printers at one time (2 USB + 1 Parallel). The Hawking HWPS12UG combined with the Internet Printing Protocol (IPP) lets you easily connect to any printer and print documents by specifying the print server's IP address. With IPP technology, printing over a WAN or the Internet becomes much easier. You can send a print job to a printer in another country just as easily as sending a print job to your home or office printer. IPP eliminates the need for fax communications between offices. Simply print an original document through the HWPS12UG's IPP capabilities and send it from one office to another. The print quality from IPP printing is equal to that of a document printed fromyour local office. The HWPS12UG will turn your printers into fully functional wireless print stations. System Requirements: Windows 95/98/2000/NT/ME/XP, NetWare, Mac OS X **, UNIX or LINUX 10Base-T Ethernet or 100Base-TX Fast Ethernet network Parallel Printer and/or USB Printer
* The HWPS12UG is not compatible with multi-function printers.
CA R E FR E E NETW ORK ING
HAWKING TECHNOLOGIES, INC
USA: Irvine, California Website: www.hawkingtech.com Email: sales@hawkingtech.com Tel: 888.662.8828, 949.580.0888 READY, NETWORK & GO! Step 1 - Connect It!
Europe: Rotterdam, The Netherlands Website: www.hawkingeurope.com Email: sales@hawkingeurope.com Tel: 31.10.245.1600
It's easy to install, it's easy to use!
Connect your printers to the HWPS12UG's printer ports. Connect to an existing network via a wireless LAN or RJ-45 Port. The HWPS12UG uses a 10/100M auto-sensing Ethernet port and is backwards compatible with the 802.11b

HWP S U G

Easy To Install And Use Easily Connect Multiple Printers To A Wired or Wireless Network No Need For a Dedicated Print Server Computer Two Year Warranty
wireless standard so you don't have to worry about what speed your network is currently using. Step 2 - Install the Drivers and Utilities Insert the setup CD into your computers' drive and run the setup program. Configuring your HWPS12UG is easy. You can use the Windows based configuration utility or configure the HWPS12UG via any web browser. Step 3 - "Add" it! Simply run the Add Printer wizard and specify that you are printing to a network printer. For Internet printing, enter the printer's URL or IP address.
SPECIFICATIONS: Interface 10/100M RJ-45 x 1 (Auto-MDIX) USB 1.1 x 2 + DB-25 x 1 (Parallel Printer Port) Supports IEEE 802.11g /b Wireless LAN Network Protocol Support IPX/SPX, TCP/IP, IPP, DHCP, LPR, Raw Printing, Novell NetWare, Windows Server-Based Printing, and AppleTalk protocols Network Operation Systems Support Windows 95/98/98SE/ME/2000/NT/XP NetWare 3.x and above Mac OS X (Supports Postscript Printers Only) Unix and Linux Encryption 64/128 Bit WEP Memory 2 MB Flash 16 MB SDRAM Power 12V DC, 1A Linear Power Adaptor Operating Environment Temp: 10~40C Humid: 10~90% Certification FCC Class B C-Tick CE

WIRELESS NETWORK DIAGRAM:
FEATURES: 10/100Mbps auto-sensing port 802.11b/g Wireless Allows you to attach the HWPS12UG to a 10Base-T or 100Base-TX wired network or a 802.11b or 802.11g Wireless network without the need for a dedicated PC print server. Capability to print from anywhere, from any computer and from any application. Includes easy Setup Disk and Quick Installation Guide. Instantly adjust the HWPS12UG's settings to your ideal printing environment.
Multiple servers and multiple protocols support Quick and Easy Installation
HAWKING PRODUCT INFORMATION: HPS1P HPS3P HPS1U HWPS1P HMPS1U 10/100M Parallel Print Server 3 Parallel Port 10/100M Print Server 10/100 USB Print Server Wireless 802.11b Parallel Port Print Server 1-Port USB Print Server for Multifunction Printers
Copyright Hawking Technologies, Inc. 2004. All rights reserved. All trademarks herein are the property of their respective owners. Product specification subjects to change without notice.