*228867*

228867

Operating instructions Mode demploi Manual de instrucciones
Safety precautions for double-insulated tools
WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: Read all instructions
1. Keep Work Area Clean. Cluttered areas and benches invite injuries. 2. Consider Work Area Environment. Dont expose power tools to rain. Dont use power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence of flammable liquids or gases. 3. Guard Against Electric Shock. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. 4. Keep Children Away. Do not let visitors contact tool or extension cord. All visitors should be kept away from work area. 5. Store Idle Tools. When not in use, tools should be stored in dry, and high or locked-up place out of reach of children. 6. Dont Force Tool. It will do the job better and safer at the rate for which it was intended. 7. Use Right Tool. Dont force small tool or attachment to do the job of a heavy-duty tool. Dont use tool for purpose not intended for example dont use circular saw for cutting tree limbs or logs. 8. Dress Properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair. 9. Use Safety Glasses. Also use face or dust mask if cutting operation is dusty. 10. Dont Abuse Cord. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. 11. Secure Work. Use clamps or a vise to hold work. Its safer than using your hand and it frees both hands to operate tool.
12. Dont Overreach / Maintain Control. Keep proper footing and balance at all times. 13. Maintain Tools With Care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. 14. Disconnect Tools. When not in use, before servicing and when changing accessories, such as blades, bits, cutters. 15. Remove Adjusting Keys and Wrenches. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 16. Avoid Unintentional Starting. Dont carry tool with finger on switch. Be sure switch is off when plugging in. 16A. Extension Cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavler the cord. Extension Cord Table
Volts Total Length of Cord in Feet

120 V 240 V

025 050

101200 201300

Ampere Rating

More Than Not More Than

guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off. 20. Only use accessories and attachments which are given in the operating instructions or in the respective catalogue. The use of accessories or insert tools or attachments other than those specified in the operating instructions can result in personal injury to you. 21. Only have repairs carried out by recognized electrical specialists. This electric tool/machine complies with respective safety regulations. Repairs may only be carried out by an electrical specialist otherwise an accident hazard for the operator can exist. 22. Wear ear protectors when using for extended periods. 23. Always use any supplied side handle, and keep it tightly secured; use both hands during operation. Keep proper footing and balance and dont overreach. Firm control of the tool is necessary should the tool bind. 24. Hold Tool by Handle(s) Provided. Do not touch uninsulated parts of tool when drilling. Exposed metal surfaces may be made live if the tool drills into electrical wiring. 25. Replacement Parts. When servicing use only identical replacement parts. 26. Polarized Plugs. To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Please read and take note of these precautions before you use the tool/machine and keep these safety precautions in a safe place!

Not recommended

17. Outdoor Use Extension Cords. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18. Stay Alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired. 19. Check Damaged Parts. Before further use of the tool, a

SAVE THESE INSTRUCTIONS

Hilti TE 15 Rotary Hammer Drill

Technical data

Input power: 650 W Voltage (versions): 115 V, 230 V, Input current: 6.3 A, 2.9 A Frequency: 5060 Hz Speed under load: 0700 r.p.m. Hammering under load: 03800 impacts/min. Single impact energy: 2.2 Joule / 1.6 ft-lb Drill bit size range: 525 mm / 3/161 dia. Optimal performance dia.: 1016 mm / 3/85/8 Drilling performance in medium-grade ^ concrete with 12 mm / 1/2 dia. drill: 42 cm3/min. (2.56 in3/min.) = 370 mm/min. Chuck type: TE-C Drill bit connection end: TE-C Automatic cut-out brushes Double insulation, class II With slip clutch Dust-tight enclosure, central and permanent lubrication (maintenance free) Variable speed switch Side handle adjustable with depth gauge
Always wear ear protectors. Always wear protective gloves. Always wear safety Double insulation glasses.
This Product is UL listed and CSA certified
Before starting to work, please read the enclosed safety precautions.
Right of technical modifications reserved.
Please note before start-up:
1. The electric supply must be the same as given on the machine nameplate. 2. This machine is double insulated and need not be grounded (earthed). 3. Do not exert undue pressure on the machine. This will not increase its performance. Just position the bit and guide it into the hole. Lubrication of chuck: The chuck is not incorporated in the lubricating system of the machine. The drill bit connection end, therefore, must be cleaned regularly and sprayed sparingly with Hilti lubricant. Start-up time at low temperatures: Shorten it by jolting the drill bit once against the base material during the start-up. Servicing: Electric tools comply with respective safety regulations. Servicing must, therefore, be carried out only by qualified electrical specialists. For your safety, only use original Hilti repair parts.

Operating:

Fig. 1: Insertion of drill bit Turn chuck to the left (symbol ( )). Insert drill bit in any position until resistance is felt. Then turn it until it moves in farther. Turn chuck to right and lock drill bit in place (symbol ()). Fig. 2: Rotary hammer drilling To hammer drill into concrete, masonry and stone, shift setting lever to indicated rotary hammer drilling position (symbol ). Fig. 3: Rotary drilling Shift setting sleeve to indicated rotary drilling position (symbol ). Only the rotary action is transmitted to the drill bit in this position. Fig. 4: Changing the chuck Pull forward sleeve and completely remove chuck. When attaching chuck pull forward sleeve and hold it there. Press chuck onto guide tube as far as it will go. Release sleeve. Turn chuck until steel balls snap into place. Note: On attaching a keyless chuck, the hammering action is automatically cut out i. e. rotary drilling only is obtained. Fig. 5: Side handle/depth gauge Unscrew side handle to release depth gauge. Adjust depth gauge and retighten.

Double insulation

The Hilti TE15 Hammer Drill is doubleinsulated for extra operator protection. The tool is equipped with a two-wire cord and two-prong plug which can be used on standard 115 volts outlets. No grounding of the tool is necessary.

cid_etlx V. 10.1 GIESE

For information only, will not be exchanged when altered!
QuantityUnit Name Specification

Date Proc.restr.

04.04.2005 09:51

Cnt-no Item-no

73113 228859
piece Stator 110/115V assy piece Rotor 110V/120V assy piece Brush holder 100/115V assy piece Connector housing assy piece Capacitor 0,22 piece Supply cord USA/CDN piece Rating plate TE 15-C 120V piece Plastite screw 45 5X35 T25 SW piece Plastite screw 45 5X16 piece Depth gauge piece Side handle assy piece Recess tapping screw ST2,9X13 piece Recess tapping screw ST3,9X45 piece Labyrinth seal piece Motor housing TE 15-C piece Bearing plate piece Ball bearing 10X26X12,4 piece Housing endcap assy piece Cooling fan piece O-ring 13,95X2,62 piece Spring washer piece Washer piece Ball bearing piece Grip unit DIN 7981 8.1990 C-H-A2K national purchase

Spare part list

HILTI Aktiengesellschaft Schaan/FL
Copyright reserved HILTI = Registered trademark

Item-no 287306

Index Name

valid as fro Drawing

29.01.04 27425

Page 1 / 5

Combihammer TE 15-C 120V

76406 287363

piece Grip cover piece Switch 100-120V piece Conductor end A1-6 piece Clamp piece Protective sleeve piece Air deflector piece Torx-soc re scr 4X18 piece Absorber piece Ball 7 G20 piece Detent sleeve piece Guide tube piece Sealing ring 14,45X16,15X3,3 piece Circlip 17X2 piece Ram piece O-ring 10,77X2,62-S-NBR70 piece Stop piece Rotary shaft seal 32X52X7 FORM AS piece Circlip 52X2 piece Retaining ring SW28 piece Ball bearing 28X52X12 piece Compression spring piece Compression spring piece Dowel pin 7X20 piece Compression spring DIN 5401 8.2002 national purchase DIN 46228-1 8.1992 national purchase

Page 2 / 5

108 110

76582 76485

piece Coupling ring piece Washer piece Retaining ring RW28 piece O-ring 11X3 70SH HITEC piece Striker piston piece O-ring 16,0x3,0 piece Coupling piece Bevel gear Z=55 piece Ball bearing 30x42x7 piece Drive piston assy piece Conrod piece Sealing ring piece Eccentric assy piece Ball bearing 61804 piece Retaining ring SW20 piece Circlip JV32 piece Coupling sleeve piece Toothed gear Z=33 piece Shim ring 14X8X0,5 piece Circlip 8X0,8 piece Supporting ring piece Retaining ring SW8 piece Circlip 24X1,2 piece Toothed gear Z=41 DIN 471 9.1981 BRUENIERT national purchase

Page 3 / 5

149 703

73440 30215

piece Bevel pinion Z=13 piece Ball bearing 9X24X7 piece Gear housing piece Setting lever assy piece Setting plate piece O-ring 17X2 70SH piece Casing piece Eccentric assy piece Sheet metal part piece Screw plug Service assy piece Support piece Cone piece Feather key 3X3X7.7 piece Seal piece Air deflector piece Compression spring 1,15X17,9X12 piece Torx-soc tapt scr M4X8 piece Torx-soc pl scr 45 4X26 piece Carbon brush set piece Reversing switch piece Ball knob piece Feather key A3X3X10 piece O-ring 17,12X2,62 piece Oil Turmopol 20HD 1L

Page 4 / 5