ABOVE ALL

NEVER let anyone, especially children push anything into holes, slots or any other opening in the case - this could result in a fatal electric shock. NEVER guess or take chances with electrical equipment of any kind - it is better to be safe than sorry!

1. Power Source

The set should be operated only from a 220-240V AC, 50 Hz. outlet. Ensure you select the correct voltage setting for your convenience.
DONT continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way switch off, withdraw the mains plug and consult your dealer.
Be sure to ground the connection properly.

2. Power Cord

Do not place the set, a piece of furniture,etc. on the power cord(mains lead) or pinch the cord.Handle the power cord by the plug.Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short
Connect the ground terminal of the AC inlet of this display with the ground terminal provided at the power outlet using the enclosed power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
6XUHO\ FRQQHFW WKH JURXQG ZLUH

English - 3 -

circuit or electric shock.Never make a knot in the cord or tie it with other cord.The power cord should be placed in such a way that they are not likely to be stepped on. A damaged power cord can cause fire or give you an electric shock. When it is damaged and need to be changed, it should be done by qualified personel.

3. Moisture and Water

Do not use this equipment in a humid and damp place (avoid the bathroom, the sink in the kitchen, and near the washing machine). Do not expose this equipment to rain or water, as this may be dangerous and do not place objects filled with liquids,such as flower vases on top of the set. Avoid from dripping or splashing. If any solid object or liquid falls into the cabinet, unplug the set and have it checked by qualified personnel before operating it any further
Battery, including those which is heavy metal-free, should not be disposed of with household waste. Please dispose of used battery in an environmentally sound manner. Find out about the legal regulations which apply in your area. Cold cathode fluoresant lamp in LCD PANEL contains a small amount of mercury, please follow local ordinates or regulations for disposal. The mains plug of the power supply is used as disconnect device and therefore shall remain readily operable. Warning: To prevent injury, this device must be securely attached to the floor/wall in accordance with the installation instrutions.

4. Cleaning

Before cleaning, unplug the set from the wall outlet. Do not use liquid or aerosol cleaners. Use soft and dry cloth.

5. Ventilation

The slots and openings on the receiver are intended for ventilation and to ensure reliable operation. To prevent overheating, these openings must not be blocked or covered in anyway.

6. Heat and Flames

The set should not be placed near to naked flames and sources of intense heat,such as an electric heater. Ensure that no naked flame sources, such as lighted candles, are placed on top of the set

7. Lightning

In case of storm and lightning or when going on holiday, disconnect the power cord from the wall outlet.
The LCD panel is very high technology product with about a million thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product. DO NOT LEAVE YOUR TV AT STAND-BY OR OPERATING WHEN YOU LEAVE YOUR HOUSE

8. Replacement Part

When replacement parts are required, be sure the service technician has used replacement parts which are specified by the manufacturer or have the same specifications as the original one. Unauthorised substitutions may result in fire, electrical shock, or other hazards.

9. Servicing

Please refer all servicing to qualified personnel. Do not remove the cover yourself as this may result in an electric shock. WARNING: When the device is not in use for a long time, disconnect from power. Instructions for waste disposal: Packaging and packaging aids are recyclable and should principally be recycled. Packaging materials, such as foil bag, must be kept away from children.

English - 4 -

Features
Remote controlled colour LCD TV. Fully integrated Digital TV (DVB-T) 100 programmes from VHF, UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system. It has 2 Scart sockets for external devices (such as video, video games, audio set, etc.) Stereo sound system (German+Nicam). Full function Teletext (1000 pages). Fastext, TOP text. Headphone connection. A.P.S. (Automatic Programming System). All programmes can be named. Forward or backward automatic tuning. Sleep timer. Child Lock. Automatic sound mute when no transmission. NTSC Playback. AV in and S-VHS in are available. It has VGA connector for external devices such as computer. It has an HDMI connector for Digital Video and Audio. This connection is also designed to accept High Definition signals. AVL (Automatic Volume Limiting) When no valid signal is detected, after 5 minutes the TV switches itself automatically to stand-by mode. PLL (Frequency Search) PC Input Plug&Play for Windows 9X, ME, Vista, 2000, XP Audio Line Out PIP, PAP, PAT is available.

Remote Controller RC 1072

Batteries 2 X AAA

Accessories
Check the supplied accessories before installation. In case of missing or damaged items please contact your dealer immediatley.

Instruction Book

UK Plug

Quick Guide

English - 5 -
Rear View and Peripheral Connections
S-VHS Input (S-Video) Video Input (FAV) Audio Inputs Headphone Audio Line Outs Subwoofer TV/AV MENU
-P/CH+ -VOLUME+ STAND-BY PC VGA Input (PC RGB) PC Audio Input RF (Antenna) (TV/DTV) Component Video Inputs (YPbPr) Component Audio Inputs
SCART 1 (EXT-1) SCART 2 (EXT-2) HDMI Input (HDMI1) For Service Use Only Power On/Off Switch Power Cord Input CI Slot
Note: Because FAV CVBS and SVHS Y are connected parallelly, the picture may blend if the two peripherals are used at the same time. Likewise, because SVHS C and SCART II R are connected parallelly, the picture may blend if the two peripherals are used at the same time. Thus these two are not to be used at the same time.

English - 6 -

Remote Control Buttons
= Stand By YELLOW / FEATURE = Feature Menu/Fastext button BLUE / INSTALL = Install Menu/Fastext button = Update / PAP Mode = Hold / GUIDE = Index Page GUIDE= Electronic Programme Guide (EPG) / PC = Reveal / PC 0 - 9 = Direct Programme - / - - / EXIT = No Function V+ = Volume Up P + = Programme Up = TV / Digital TV Mode = External Source (TV, EXT1, EXT2, EXT2 S, FAV, S-VIDEO, HDMI, YPBPR, PC, DTV) PP = Personal preference = Cursor Up = Cursor Right OK/SELECT = OK (Store) = Cursor Down M = Menu = Cursor Left I-II = Mono/Stereo - Dual I-II / INFO = Info - P = Programme Down = Mute - V = Volume Down P<P = Previous Programme / WIDE / / = Teletext = Time / subtitle on / off in the digital mode = Image size / Expand = PIP Mode / Mix
RED / SOUND = Sound Menu/Fastext button
GREEN / PICTURE = Picture Menu/Fastext button

English - 7 -

Preparation
For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Use this product in moderate climates, operating temperature range for this product is 0-40 Degrees Celsius. Note: Remove the battery from remote control handset when it is not to be used for a long period. Otherwise it can be damaged due to any leakage of battery.

To start installation process, select Yes, to cancel select No. To select an option Yes or No, highlight the item by using _ / ` buttons and press the SELECT button. The IDTV will automatically tune to the UHF transmision channels 21 to 68 looking for digital terrestrial TV broadcasts and displaying the names of channels found. This process will take about five minutes. To cancel searching, you can press the "M" button at any time during the process.

To switch the TV off

Press the (stand-by) button on the remote control or On/Off switch on the TV, so the TV will switch to stand-by mode. To power down the TV completely, press Power On/ Off button or unplug the power cord from the mains socket.
Navigating the Menu System
1- Press M to display the menu. 2- Press b or a button to select an icon. Press ` for more options.
After Automatic Search process is completed, the following message asking for analogue channel search appears on the screen. TV switches to the analogue TV mode.
4- Press _ or ` buttons to change the settings. Press OK to set as default. 5- To exit the menu or return from sub-menu screen, press M. These explanations are available for the navigation of the whole Menu System. To select options that are explained in the following parts, refer to Navigating The Menu System.
3- Use b or a button to highlight.
To seach for analogue channels, select Yes. The menu below is displayed to search for analogue channels.

English - 11 -

Basic Operations
You can operate your TV using both the remote control and onset buttons.
Operation with the buttons on the TV

Volume Setting

Press - button to decrease volume or + button to increase volume, so a volume level scale (slider) will be displayed at the middle of the bottom on the screen.

Programme Selection

Press P/CH + button to select the next programme or P/CH - button to select the previous programme.

Entering Main Menu

By pressing _ / ` button, adjust the Country item and press b to highlight Language item. Use _ / ` button to set Language. Use _ / ` buttons to select TXT Language and set it by using _ / ` buttons. Press OK button to continue: Press the MENU button to enter Main menu. In the Main menu select sub-menu using P/CH - or P/CH + buttons and enter the sub-menu using - or + buttons. To learn the usage of the menus, refer to the Menu System sections (pages 15 or 21).

In the EPG Menu all channels are displayed. Current channel is highlighted. Use a / b buttons to change or buttons to make page channels. Also press up/down scroll for the channels. If you highlight an event, short event description, extended event description, start and finish times of event are displayed on the screen. When the current programme is highlighted, the box is switched to the highlighted channel by pressing the SELECT button. If you press the SELECT button when a next event is highlighted, a reminder is set for the highlighted programme and a clock appears across the highlighted channel line. Programme reminders can be set to signal that a programme is about to start when you are watching another channel. If you set reminder to a programme, then you will be asked for switching to that channel when the reminder time is reached. Press the M button to view the 7 day EPG. Press a / b button to navigate in Channels or Programmes. Press _ / ` button to navigate through the channel and programme list.
The information banner gives a number of facts on the channel selected and the programmes on it. The name of the channel is displayed, along with its channel list number and an indication of the strength of the signal received on this tuning channel. Hint Not all channels broadcast the programme data. If the name and times of the programmeis not available then No Information Available are displayed in the information banner. Icons are also displayed in the information banner and if this channel is a favourite channel: Favourite channel icon.
If the selected channel is locked, you must enter the correct four digit code to view the channel.

See page 16 for details.

Electronic Programme Guide (EPG)
Some, but not all, channels send information about the current and next events. Please note that event information is updated automatically. If there is no event information data available in channels, only channel names with No Information Available banner is displayed. Pressing the GUIDE button again exits EPG menu. In EPG Menu, you can easily see the extended help information by pressing INFO button and by press With RED/GREEN buttons you can change sched-

English - 13 -

ule time. By pressing YELLOW/BLUE you can advance the schedule backward / forward of a day. If you press INFO button you can see the detailed help information easily. And by pressing INFO button again you can exit Help menu. The starting time for EPG is the current time.You can see the event information for the next two hours. By pressing a / b button, you can go to the next/ previous hours while Programmes list is highlighted. lf you press the SELECT button when a next event is highlighted, a reminder is set for the highlighted programme and a clock appears on the screen. Programme reminders can be set to signal that a programme is about to start when you are watching another channel. If you set reminder to a programme, then you will be asked for switching to that channel when the reminder time is reached.

English - 14 -

IDTV Menu System
The IDTV menu can only be shown when watching Digital terrestrial broadcasting. Press the button to turn IDTV on while TV is in analogue mode. Press the "M" button. The menu below appears on the screen:
To watch a specific channel, highlight it using a / b button and then press SELECT button, while the SELECT item on Channel List menu is highlighted by using _ / ` button. Then the name and number of the selected channel will be displayed in the top-left and top-right of the channel display at the top-right of the screen, respectively.

deleted.

Deleting the channels in the channel list Press a / b button to select the channel that will be
Press _ / ` button to select the Delete item on Channel List menu. As seen on Channel List menu, SELECT is written next to Delete item at the bottom of the screen to indicate that press the SELECT button to delete the highlighted channel in the channel list.

Channel List

Using the a / b button on the remote control in Main menu, make sure that the first item, Channel List, is highlighted and press the SELECT button to display the Channel List. The following operations can be performed in this menu: 1. Navigating the whole list of channels 2. Deleting channels 3. Renaming channels 4. Adding locks to channels 5. Setting favourites Channel List is the place where the channels are managed. Press the SELECT button to delete the highlighted channel in the channel list. Then the message below appears on the screen.
Press _ / ` button to highlight the desired option. If SELECT button is pressed while Yes is highlighted, the highlighted channel is deleted. Selecting No cancels the delete operation.

Renaming channels

To rename a specific channel, the channel must be highlighted via pressing a / b button and then highlight the Edit Name item by pressing _ / ` button. Press the SELECT to activate rename feature.
Navigating the whole channel list Press a / b button for selecting the previous or next
channel. You can press up or page down. or button to move page

English - 15 -

Setting Favourites
You can set various channels as favourites so that only the favourite channels are navigated. To set a favourite you should highlight the Favourites item at bottom of the Channel List menu. Use the _ / ` button to highlight the Favourites item at the base of the screen and then, in turn, highlight each channel you want to add to the favourites list, using the a / b buttons (or press the SELECT button. Now pressing _ / ` button moves to the previous/ next character. Pressing a / b button toggles the current character, i.e., b character becomes a by b and c by a. Pressing the numeric buttons 0.9 replaces the highlighted character with the characters printed above the button one by one as the button is pressed. Press the "M" button to cancel the editing or SELECT button to save the new name. / buttons), and

Press the OK button to search for analogue channels.The following menu appears on the screen for analogue channel search.
First of all choose Language,Country and TXT Language by using a / b and _ / ` buttons. This will affect the sort process in APS. To start APS press OK button:
,QVWDOODWLRQ $GG 1HZ &KDQQHOV )LUVW 7LPH ,QVWDOODWLRQ
By selecting YES and pressing the OK button, the existing channel table will be deleted. After factory settings is loaded, First Time Installation menu will be displayed. After APS is finalized, the programme table will appear on the screen. In the programme table you will

English - 17 -

see the programme numbers and names assigned to the programmes. If you do not accept the locations and / or the programme names, you can change them in the Program menu.
and enables the automatic display of subtitles whenever subtitle information is broadcast. Highlight the Subtitle line in the Configuration menu and use the _ / ` button to cycle through Off and language options. Favourite mode This function enables or disables the favourite channel list mode. See Channel List menu Favourites on page 16. Use _ / ` button to turn on/off favourite mode. If the Favourite Mode is on, in normal operating mode pressing P+ and P- buttons will only navigate through the channels that were previously defined as favourites in Channel List. EPG Preference Digital terrestrial television channels can broadcast simultaneous Next&Now and 7-Day electronic programme. Highlight the EPG Preference line in the Configuration menu and use the _ / ` button to select Next&Now or 7-Day. Receiver Upgrade The IDTV can be upgraded via the configuration menu, entered from the main menu. In the Configuration menu, highlight the Receiver Upgrade item by pressing _ / ` button and press the SELECT button to start upgrade process. There are two possibilities for Receiver software to be upgraded: automatic and manual.

Configuration

Press the "M" button to display the Main Menu and the b button twice to highlight Configuration, then press the SELECT button to display the Configuration menu. Press the "M" button to leave the menu.

The various configuration functions are displayed in a list, along with a quarter-screen image of the currently selected channel. You can select a function by highlighting the corresponding menu line using the a / b button.
Audio Language Digital terrestrial television channels can broadcast simultaneous soundtracks in more than one language. This function selects which language soundtrack you will hear when switching to a channel broadcasting with the multiple soundtracks. Highlight the Audio Language line in the Configuration menu and use the _ / ` button to cycle through the language options. Subtitle Digital terrestrial television channels can broadcast subtitles displayed on-screen for the hard-of-hearing. This function selects the desired subtitle language Automatic Download (Automatic upgrade) Automatic Download can be enabled or disabled by pressing _ / ` button. If it is enabled, then there are two ways for automatic upgrade. The first one is checking the existence of a new software every time the IDTV goes to standby. The second one is waking up at 03:00 a.m. every night, provided that the IDTV is left in standby mode. Both automatic upgrade methods result in standby mode either upgraded or not. If the automatic upgrade is set to Disabled then this function will not work. Search For New Version (Manual upgrade)

English - 18 -

Manual upgrade starts if the Search for New Version item is highlighted by using a / b button and activated via pressing the SELECT button. After Search for New Version is activated, the IDTV tunes to each frequency that have been stored in its database and looks for the new software.

Timers

You can set a timer to switch the TV to any channel without your intervention. This is also for making video recordings of programmes when you are out. Display the Main Menu by pressing the "M" button. Highlight the Timers line by pressing a / b button and press the SELECT button to display the Timer menu.
Parental Settings Some channels broadcast material which you do not want younger members of the family to watch. Any channel can be locked so that it cannot be selected for viewing without first a four-digit PIN code being entered. In this way any channel not suitable for younger viewers can be protected. This function enables or disables the menu protection system and allows the PIN code to be changed. Use a / b button to go to Parental Settings option. Press the SELECT button to enter Parental Settings Menu. A box asking for the lock key is displayed. Up to five separate timer events can be set and each is displayed in the Timer screen, showing the event number, the channel to be selected, the start time, end time, date and the mode - whether that event is active (and will be acted on) or not.

There is only one key which is set to 0000 initially. Enter lock key. If wrong Lock key is entered, the following message is displayed on the screen and it is returned back.
If it is correct, the Parental Settings Menu including following items is displayed:
There you can set/reset locking for the Main Menu, or the Installation Menu to restrict access. If the menu lock is disabled, there will be free access to the menu system. Also in this menu you can change the lock key and set/change parental lock mode. Disabled: All menus are unlocked. Main Menu: Main menu is accessible only with the correct lock key. So the user cannot add, delete, rename, move channels, cannot set timers. Installation: Installation menu is locked, so the user cannot add channels. Changes will be updated after exiting Configuration Menu.
To set an event, highlight its mode button using the a / b button and press the SELECT button to display the timer entry window.
Here the five settings of channel name, start time, end time, date and frequency mode can be set. You can move freely between each setting using the a / b buttons.

English - 19 -

The channel name is set using the _ / ` button to display the channel which broadcasts the programme. The start time, end time and date are each set with the digit buttons on the remote control in 24-hour format. The frequency mode determines how often the receiver operates this event and is set with the a / b button to be either Once, Daily, or Weekly. If an invalid number for the start or end times or the date is entered, Entered time is not valid message appears on the menu. If timer action occurs while the TV is watched, the TV switches to the selected channel. When timer expires, the TV switches to the channel which it is switched from. Selected digital channel will be output via Scart-2. You should connect your VCR to Scart-2 for recording digital broadcast.

TV Setup

To be able to go through TV functions, you can use this item. The digital TV Setup menu screen is accessed from the main menu. Press the "M" button to display the main menu and use a / b button to highlight TV Setup, press the SELECT button to display TV Setup menu screen.

Language

Some programmes are broadcast in two or more languages simultaneously. The language heard can be selected from the Language Menu. Press the "M" button to display the Main Menu and use a / b button to highlight the Language line and press the SELECT button. Detailed information about Sound, Picture and Feature menus are in AnalogueTV Menu System section on page 21.

&KDQQHO /LVW ,QVWDOODWLRQ &RQILJXUDWLRQ 7LPHUV /DQJXDJH 79 6HWXS &RPPRQ ,QWHUIDFH
Use the a / b button to highlight the soundtrack language required and press the SELECT button. Normal viewing, with the required language soundtrack, can be resumed by pressing the "M" button.

Common Interface

Press the "M" button to display the Main Menu and use the a / b button to highlight the Common Interface line and press the SELECT button.

/DQJXDJHV

It is required to subscribe to a pay channel company to view the pay channels of the Digital Terrestrial broadcasting. Obtain the Conditional Access Module (CAM) and the Viewing card by subscribing to a pay channel company, then insert those to the Television using the following procedure.

English - 20 -

1. Switch off the TV and unplug from the mains. 2. Insert the CAM, then Viewing Card to the slot that is located in the terminal cover at the left-hand side of the TV (from front view). The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. 3. Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. Some CAMs may require the following set up. Please set the CAM by entering the IDTV menu, Common Interface then pressing the SELECT button. (CAM set up menu is not displayed when it is not required.) To see the viewing contract information: Enter IDTV; press the "M" button, then highlight Common Interface and press the SELECT button. When no module is inserted, No Common Interface module detected message appears on the screen. Refer to the module instruction manual for details of the settings.

Analogue TV Menu System

Picture Menu

3,&785(

In picture menu if PC,YPbPr or HDMI modes are selected, resolution information is displayed at the bottom of the menu osd.
By pressing a / b button, select Mode. Press _ / ` button to choose from one of these options: Cinema, Dynamic and Natural.
Contrast/Brightness/Sharpness/Colour/Hue By pressing a / b button, select the desired Option.

In the Feature menu, highlight PAP item by pressing a / b buttons. Press ` button to enter PAP submenu:

PIP ON-OFF

You can activate or deactivate PIP mode by pressing / button.

PIP Picture

Press button to enter PIP Picture submenu. Adjustments of Contrast, Brightness, Sharpness, Colour, Hue, Reset and Store items in this part are identical with Picture menu in the Menu System. Refer to Picture menu explanations in the previous parts.

PAP ON-OFF

You can activate or deactivate PAP mode by pressing / button.

PAP Picture

Press button to enter PAP Picture submenu. Adjustments of Contrast, Brightness, Sharpness,

English - 23 -

Colour, Reset and Store items in this part are identical with Picture menu in the Menu System. Refer to Picture menu explanations in the previous parts.

PAP Source

Select PAP Source item by using a / b button. Use / button to set PAP source. Note: When main picture source is TV, EXT-1, EXT-2, FAV or S-VIDEO, PIP Window can only be set to HDMI, YPBPR, PC source or vice versa.
Note: If the currently watched source is analogue TV, a connected device displays analogue TV source as well. If this source is set to digital mode, connected device displays digital source. In order to avail this function, EXT-2 Output should be set to TV/DTV.

PC Audio In

By pressing a / b select Pc Audio In.By pressing _ / ` button, you can change the PC Audio In to TV, EXT-1, EXT-2, FAV, YPbPr Audio, PC Audio or FAV.

PAP Programme

Select PAP Programme item by using a / b button. PAP Programme is displayed at the bottom of menu OSD. Use / button to set PAP Programme. You can also use digit buttons on the remote control to set PAP Programme.

Blue Background

You can set the TV to automatically change to a blue screen if the signal is weak or absent, or when there is no input from an external device. The Blue Background feature can be turned on or off by pressing _ / ` button.

PAP Swap

Select PAP Swap item by using a / b button. Use / button. This function enables to swap between the main and the PAP picture.

Sleep Timer

By pressing a / b select Sleep Timer.Press _ / ` button to set the Sleep Timer. The timer can be programmed between Off and 120 minutes in steps of 10 minutes.

Search

By pressing a / b button, select Search. Press _ / ` button to start program searching.You can also enter the desired frequency via digit buttons when search item is highlighted.
By pressing a / b button, select Store. Press or OK button to store the adjustments. Stored. will be displayed on the screen. In source menu, highlight a source by pressing a / b button and switch to that mode by pressing or OK button. Source options are; TV, DTV, EXT-1, EXT-2, EXT-2 S, FAV, S-VIDEO, HDMI, YPBPR and PC. Note: You can mark desired source options by pressbutton ing OK button. Therefore, when is pressed, only the marked source options will be available.

Install menu in AV modes

The following screen appears in the install menu:

English - 26 -

PC Mode
Power off both Computer and Display before making any connections. Set your PCs resolution correctly before connecting to the TV. See the table on Appendix page. Use 15-pin display cable to connect a PC to the LCD TV. Note: PC menu will not be active for TV sets without a PC input.

H (Horizontal) Position

This item shifts the image horizontally to right hand side or left hand side of the screen. Select H Position item by using Use
_ / ` button to adjust the value.

a / b button.

V (Vertical) Position
This item shifts the image vertically towards the top or bottom of the screen. Select V Position item by using Use

Menu System in PC mode

Sound Menu/Feature Menu
The items in these menus are described at Sound & Feature Menu explained in Menu System.
Depending on the resolution and scan frequency that you input to the TV Set, you may see a hazy or noisy picture on the screen. In such a case you can use this item to get a clear picture by trial and error method. Use
Picture menu appears on the screen.
PC Picture Menu By pressing a / b button, select the second icon. PC

Dot Clock

Dot Clock adjustments correct interference that appear as vertical banding in dot intensive presentations like spreadsheets or paragraphs or text in smaller fonts. Use
Brightness, Contrast and Colour Temperature adjustments in this menu are identical to adjustments defined in TV picture menu in MENU SYSTEM.
POSITION menu appears on the screen.
PC POSITION Menu By pressing a / b button, select the sixth icon. PC

Sound in PC mode

Connect the PCs Audio output to the TVs PC Audio In socket with an audio cable.

Connect a decoder with an aerial socket to the TV
Connect the aerial cable.
Connect a decoder without an aerial socket to the TV
Connect the decoder to the EXTERNAL socket of TV with a RCA cable. Through the SCART/RCA socket of the decoder, you may attain a better display resolution.

TV And Video Recorder

Connect the aerial cables. Better picture quality can be obtained if you also connect a Scart cable to SCART sockets.

Playback NTSC

Connect NTSC VCR player to a Scart socket of the TV.

English - 30 -

Then, press the AV button to select EXT1 or EXT2.

Copy Facility

Source selection for VCR recording. Select Feature menu. Select SCART 2 Out by pressing

Care Of The Screen

Clean the screen with a slightly damp, soft cloth. Do not use abrasive solvents as they may damage the TV screen coating layer.

_ / ` button.

For copying the picture that comes from the tuner, select SCART 1. Note :Scart-1 socket cannot be used as DTV output. Please use Scart-2 instead.

Poor Picture

Have you selected the correct TV system? Is your TV set or house aerial located too close to non-earthed audio equipment or neon lights, etc.? Mountains or high buildings can cause double pictures or ghost images. Sometimes you can improve the picture quality by changing the direction of the aerial. Is the picture or Teletext unrecognisable? Check if you have entered the correct frequency. The picture quality may degrade when two peripherals are connected to the TV at the same time. In such a case, disconnect one of the peripherals.

Camera And Camcorder

To Connect to AV Input
Connect your camera or camcorder to AV input of the TV. Connect your equipment to the TV via VIDEO (yellow), AUDIO R (red) and AUDIO L (white) inputs. You must connect the jacks into the input with the same colour.
To Connect To S-VHS Input
Connect your camera or camcorder S-VHS input of the TV. Connect your equipment to the TV via S-VHS input and audio inputs of AV inputs by using S-VHS cables.

No Picture

Is the aerial connected properly? Are the plugs connected tightly to the aerial socket? Is the aerial cable damaged? Are suitable plugs used to connect the aerial? If you are in doubt, consult your dealer. No Picture means that your TV is not receiving a transmission. Have you selected the correct button on the remote control?Try once more.

(TV, EXT1, EXT2, EXT2 S, FAV, S-VIDEO,HDMI,YPBPR, PC, DTV) PP = Personal preference = Cursor Up = Cursor Right OK/SELECT = Okay (Store) = Cursor Down M = Menu = Cursor Left I-II = Mono/Stereo - Dual I-II / INFO = Info - P = Programme Down = Mute - V = Volume Down P<P = Previous Programme / WIDE / / = Image size / Expand

TV DTV

= PIP Mode / Mix
= Teletext = Time / subtitle on / off in the digital mode
31 RED / SOUND = Sound Menu 32 GREEN / PICTURE = Picture Menu

English - 7 -

Preparation
For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. Use this product in moderate climates, operating temperature range for this product is 0-40 Degrees Celsius. Note: Remove the battery from remote control handset when it is not to be used for a long period. Otherwise it can be damaged due to any leakage of battery.
Handling the Remote Control
Before Switching On Your TV

Power Connection

IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.
It could cause corrosion or battery leakage and may result in physical injury and/or property damage including fire. Never mix used and new batteries in the device. Replace all the batteries in a device at the same time. Remove the batteries if the remote control is not going to be used for an extended period of time. To avoid possible failure, read the following instructions and handle the remote control properly. Do not drop or cause impact to the remote control. Do not spill water or any liquid on the remote control. Do not place the remote control on a wet object. Do not place the remote control under the direct sunlight or near sources of excessive heat. Note: Remove the battery from remote control handset when it is not to be used for a long period. Otherwise it can be damaged due to any leakage of battery.
Connections to the Aerial Input Socket
Connect the aerial or cable TV plug to the Aerial input socket located at the rear of the TV and connect the cable plug coming out from the TV out socket located on the devices (VCR, DVB etc.) to this socket as well.

Operating Range for the Remote Control
Point the top of the remote control toward the LCD TV's remote sensor LED while pressing a button.

VHF/UHF

CABLE TV

REAR OF THE TV

Inserting Batteries in the Remote Control Handset
WARNING : Remote control is battery included. A plastic protector is used to disconnect the batteries in order to prevent the battery life from reducing. Please remove the plastic protector before the first use. Remove the battery cover located on the back of the handset by gently pulling backwards from the indicated part. Insert two AAA/R03 or equivalent type batteries inside. Place the batteries in the right directions and replace the battery cover.
SOUN D PICTURE EATURE ST L A L

W ID E

EF G HI

MNO PQ R

V WX YZ

P< P

C 1072
Remote range is approximately 7m/23ft.

English - 8 -

Switching The TV ON/OFF

To switch the TV on

Your TV will switch on in two steps: 1- Connect the power supply cord to the system. Press Power On/Off button.Then the TV switches itself to stand-by mode (Optional). 2- To switch on the TV from stand-by mode either: Press a digit button on the remote control so that a programme number is selected, or Press the -P/CH or P/CH+ button on the TV or press the P- or P+ button on the remote control, so that last mode switched off is selected. By either method the TV will switch on.

Initial Settings

When the TV is turned on for the first time, it is in the digital mode. Because this is the first time the TV is used, there are no channels stored in the memory and the following message appears on the screen.
Please ensure aerial is plugged in. Do you want to start first time installation? Yes No
To start installation process, select Yes, to cancel select No. To select an optionYes or No, highlight the item by using / buttons and press the SELECT button. The IDTV will automatically tune to the UHF transmision channels 21 to 68 looking for digital terrestrial TV broadcasts and displaying the names of channels found. This process will take about five minutes. To cancel searching, you can press the "M" button at any time during the process.

AV Mode

APS is running.
Press the TV/AV button at the control panel on the the TV to switch your TV to AV modes.
Operation with Remote Control
UK 63.75 MHz 6% 63.75 MHz

P 03 - C 04

The remote control of your TV is designed to control all the functions of the model you selected. The functions will be described in accordance with the menu system of your TV. Functions of the menu system are described in the following sections.

Cancel

Press V + button to increase volume. Press V - button to decrease volume. A volume level scale (slider) will be displayed in the middle at the bottom of the screen.
After APS is finalized, a programme list will appear on the screen. In the programme list you will see the programme numbers and names assigned to the programmes. If you do not accept the locations and / or the programme names of programmes, you can change them in Insall Menu. For details see Install Menu section. To display channel list in IDTV, switch to the IDTV via pressing the TV DTV button. Then press the M button to enter main menu, Channel List will be highlighted. Press the SELECT button to enter the menu.
Programme Selection (Previous or next programme)
Press P- button to select the previous programme. Press P+ button to select the next programme.
Programme Selection (direct access)
Press digit buttons on the remote control to select programmes between 0 and 9. TV will switch to the selected programme. To select programmes between 10 - 999 (for IDTV) or 10-99 (for analogue), press the digit buttons consecutively which programme you want to select (eg. for programme 27, first press 2 and then 7). When it is too late to press second digit button only the first digit programme will be displayed. The limit of the delay time is 3 seconds.

English - 10 -

Press directly the programme number to reselect single digit programmes.
ing this button again you can close this window.

Everyday Operation

Pressing the TV DTV button at any time while watching television programmes will switch the TV set between displaying the digital terrestrial television broadcasting and its normal analogue broadcasting.
Rolling national and international news including breaking news as it happens, business updates, sports results and weather summaries.

Press / button to navigate through the channel and programme list.

Enter Lock Key

See page 14 for details.
Electronic Programme Guide (EPG)
Some, but not all, channels send information about the current and next events. Please note that event information is updated automatically. If there is no event information data available in channels, only channel names with No Information Available banner is displayed. Pressing the GUIDE button again exits EPG menu. In EPG Menu, you can easily see the extended help information by pressing INFO button and by pressChannels Programmes on Saturday 21/8, 13:00 - 15:00 30. CBBC Channel 13:00 Chuckle Vision (Now) 40. BBC NEWS 24 14:00 Tracy Beaker 41. ITV News 14:55 Newsround 50. Four Text 800. BLUE/LEFT 1k. 801. CCIR17/1kHz.

Change Time

Change Day

I More

WithRED/GREEN buttons you can change sched-

English - 11 -

ule time. By pressing YELLOW/BLUE you can advance the schedule backward / forward of a day. If you press INFO button you can see the detailed help information easily. And by pressing INFO button again you can exit Help menu. The starting time for EPG is the current time.You can see the event information for the next two hours. By pressing / button, you can go to the next/ previous hours while Programmes list is highlighted. lf you press the SELECT button when a next event is highlighted, a reminder is set for the highlighted programme and a clock appears on the screen. Programme reminders can be set to signal that a programme is about to start when you are watching another channel. If you set reminder to a programme, then you will be asked for switching to that channel when the reminder time is reached.

Digital Teletext

With Digital terrestrial broadcasting (DVB-T), in addition to pictures and sound, you can also watch digital teletext. Digital teletext is sometimes broadcast at the same time as normal broadcasting. 1. Press the button. The digital teletext information appears. 2. Operate it with the coloured buttons, buttons and OK button. , / ,
The operation method may differ depending on the contents of the digital teletext. Follow the instructions displayed on digital teletext screen. When Press SELECT button or similar message appears on the screen, press the SELECT button. When the (Text) button is pressed, the TV returns to television broadcasting.

Newsround

16:55-17:00
Channels 30. CBBC Channel 40. BBC NEWS 24 41. ITV News 50. Four Text 51. BBCI 800. BLUE/LEFT 1k. 801. CCIR17/1kHz.
Programmes on Saturday 21/8, 15:00 - 17:00 15:00 Even Stevens 15:50 Newsround Showbiz 16:00 Basil Brush 16:55 Newsround
With Digital terrestrial broadcasting (DVB-T), in addition to digital teletext broadcasting at the same time as normal broadcasting, there are also channels with just digital teletext broadcasting. The aspect ratio when watching a channel with just digital teletext broadcasting is the same as the aspect ratio of the picture watched previously. When you press the (Text) button again, the digital teletext screen is displayed.
Over Air Download Displaying The Subtitles
With Digital terrestrial broadcasting (DVB-T), some programmes are broadcast with subtitles. Subtitles can be displayed when watching these programmes. Press the M button to display the Main menu, highlight the Configuration line using / button andpress the SELECT button to display the Configuration menu. Highlight the Subtitle item in Configuration menu and use / button to set Subtitle to off or a language. If Subtitle is on via selecting one language option, pressing the button causes the following warning message display on the screen. Pressing the GUIDE button again exits EPG menu.
Interactive services cannot be used while subtitles are on. Would you like to turn subtitles off now? Yes No
To ensure that your IDTV always has the most up-todate information, please ensure that after use it is set to its standby mode. At 3AM each day, the IDTV automatically searches for any new information which may be broadcast and will download this to your IDTV automatically. This operation will normally take approximately 30 seconds. If you want to do this, you need to set Automatic Download to Enabled in Receiver Upgrade setting. For details see page 16.

Widescreen

Depending on the type of broadcast being transmitted, programmes can be viewed in a number of formats. Press the WIDE button repeatedly to select between Auto or 16:9. When Auto is selected, the format being displayed is determined by the picture being broadcast. Please Note: Menu size changes depending on the chosen image size.

Enter the password using the digit buttons on the will now be disremote control. The Lock icon played next to the selected channel. Repeat the same operation to cancel the Lock.
Language TV Setup Common Interface

English - 14 -

This menu includes the following items: 1. Add New Channels 2. First Time Installation. ADD NEW CHANNELS: This tuning menu consists of two parts: Automatic Search Manual Search Installation
Press the OK button to start installation. After search is completed for digital channels, a message asking search for analogue channels appears on the screen.
Add New Channels Automatic Search First Time Installation Manual Search
Automatic Search: Automatic search is started by pressing the OK button in the auto-search pop up menu. All the services are searched and a channel table is created automatically. All channels found are stored in a sorted form with respect to their channel numbers. Some services may not appear with the correct channel number. At the time of printing, not all broadcasters are sending their channel number information. Manual Search: In manual search, the number of the multiplex is entered manually and only that multiplex is searched for the channels. For every valid channel number, signal level, signal quality and network name are shown at the bottom of the screen. In both manual and auto search any existing channel in the database is not re-stored to avoid redundant duplicates of that channel. FIRST TIME INSTALLATION The user can use this item to load default settings, which had been loaded to the receiver at the factory. To install factory settings, highlight First Time Installation menu and press the OK button, then you will be asked to confirm for deleting all channels and settings.
Press the OK button to search for analogue channels.The following menu appears on the screen for analogue channel search.
First of all choose Language,Country and TXT Lan/ and / buttons. This will guage by using affect the sort process in APS. To start APS press OK button:
Installation Add New Channels First Time Installation
Your previous digital channel list will be destroyed. Are you sure you want to delete all digital channels and settings for first time installation? Yes No

TV Setup

To be able to go through TV functions, you can use this item. The digital TV Setup menu screen is accessed from the main menu. Press the "M" button to display the main menu and use / button to highlight TV Setup, press the SELECT button to display TV Setup menu screen.
Detailed information about Sound, Picture and Feature menus are in AnalogueTV Menu System section on page 19.

Language

Some programmes are broadcast in two or more languages simultaneously. The language heard can be selected from the Language Menu. Press the "M" button to display the Main Menu and use / button to highlight the Language line and press the SELECT button.

Common Interface

Press the "M" button to display the Main Menu and / button to highlight the Common use the Interface line and press the SELECT button.
Channel List Installation Configuration Timers Language TV Setup
Use the / button to highlight the soundtrack language required and press the SELECT button. Normal viewing, with the required language soundtrack, can be resumed by pressing the "M" button.
It is required to subscribe to a pay channel company to view the pay channels of the Digital Terrestrial broadcasting. Obtain the Conditional Access Module (CAM) and the Viewing card by subscribing to a pay channel company, then insert those to the Television using the following procedure.

Languages

English

English - 18 -

1. Switch off the TV and unplug from the mains. 2. Insert the CAM, then Viewing Card to the slot that is located in the terminal cover at the left-hand side of the TV (from front view). The CAM should be correctly inserted, it is impossible to insert fully if reversed. The CAM or the TV terminal may be damaged if the CAM is forcefully inserted. 3. Connect the TV to the mains supply, switch on and then wait for few moments until the card is activated. Some CAMs may require the following set up. Please set the CAM by entering the IDTV menu, Common Interface then pressing the SELECT button. (CAM set up menu is not displayed when it is not required.) To see the viewing contract information: Enter IDTV; press the "M" button, then highlight Common Interface and press the SELECT button. When no module is inserted, No Common Interface module detected message appears on the screen. Refer to the module instruction manual for details of the settings.

By pressing / button, select Reset. Press or OK button to reset the picture modes to factory default settings.

balance

By pressing / button, select Balance. Press button to increase balance to the right. Press button to decrease balance to the left. Balance level can be adjusted between -32 and +32. Press the M button to return to the previous menu.

Sound Menu

Volume Equalizer Balance Headphone Sound Mode

Sound Mode

By pressing / select Sound Mode. Press / button, you can select Mono, Stereo, Dual I or Dual II mode, only if the selected channel supports that mode.
By pressing / select AVL VL.Press set the AVL as on or off. / button to

Effect

By pressing / select Effect.Press to set Effect as on or off. / button

Dynamic Bass Volume

By pressing / select Volume. Press button to change the level of the Volume. / Dynamic Bass is used to increase bass effect of the TV set. By pressing / button, select Dynamic Bass. By pressing / button set Dynamic bass to Low, High or Off. It is not recommended to select High if listening at high volume levels. There is a subwoofer output that can accept an active subwoofer if you wish to create very high levels of Bass. Subwoofer is active only if Dynamic Bass is set to Off.

Equalizer

By pressing / select Equalizer. Press / button to change the Equalizer setting. In equalizer menu, the mode can be changed to Pop, Rock, Jazz, Flat, Classic or User. Select the desired frequency by / button and increase or decrease the frequency gain by pressing / button. Note: Equalizer menu settings can be altered only when the Equalizer Mode is in User.

Subwoofer

It is possible to connect an external, active subwoofer to the set to give a much deeper bass effect. By pressing / button, select Subwoofer. Subwoofer can be set to On or Off. Dynamic Bass is not available if Subwoofer is set to On.

Balance

By pressing / select Balance.Press / button to change the level of the balance.Balance level can be adjusted between -32 and +32.

English - 20 -

Set Subwoofer to On when you connect an external subwoofer to the set.

PIP Position

Select PIP Picture item by using / button. Use / button to adjust PIP position. PIP Position info will be displayed at the bottom of the menu OSD.

Features Menu

PIP Source
PIP PAP Sleep Timer Child Lock Language
Select PIP Source item by using / / button to set PIP source.

button. Use

Note: When main picture source is TV, EXT-1, EXT-2, FAV or S-VIDEO, PIP Window can only be set to HDMI, YPBPR, PC source or vice versa.

PIP Programme

Select PIP Programme item by using / button. PIP Programme is displayed at the bottom of menu OSD. Use / button to set PIP Programme. You ou can also use digit buttons on the remote control to set PIP Programme. If the source is set to HDMI, PC or YPBPR; PIP Programme line will be visible in PIP menu. Otherwise, this line will not be visible.
In the Feature menu, highlight PIP item by pressing / buttons. Press button to enter PIP submenu:

PIP Swap

Select Swap item by using / button. Use / button. This function enables to swap between the main and the PIP picture.
In the Feature menu, highlight PAP item by pressing / buttons. Press button to enter PAP AP submenu:
PIP ON-OFF PIP Picture PIP Position PIP Source

PAP ON-OFF

PAP Picture PAP Source PAP Programme PAP S wap

PIP ON-OFF

You can activate or deactivate PIP mode by pressing / button.

PIP Picture

Press button to enter PIP Picture submenu. Adjustments of Contrast, Brightness, Sharpness, Colour, Hue, Reset and Store items in this part are identical with Picture menu in the Menu System. Refer to Picture menu explanations in the previous parts.
You can activate or deactivate PAP mode by pressing / button.

PAP Picture

Press button to enter PAP Picture submenu. Adjustments of Contrast, Brightness, Sharpness,

English - 21 -

Colour, Reset and Store items in this part are identical with Picture menu in the Menu System. Refer to Picture menu explanations in the previous parts.

PAP Source

Teletext Language

By pressing / button, select Teletext Language. Press / button to change Teletext Language to West, East, Turk/Gre,Cyrillic or Arabic.

Default Zoom

Default zoom is a feature that provides the zoom mode of the TV set to be switched to the selected default zoom mode (Panoramic, 4:3 ,14:9 zoom,16:9) in case no WSS or 4:3 signal by end-user. By pressing / button, select Default Zoom. You ou can set Default Zoom to Panoramic, 4:3, 14:9 Zoom or 16:9 by pressing / button.
By pressing / button, select Language.Use / button to select the language. Available languages are: English, French, German, Italian, Spanish, Portuguese, Dutch, Greek, Swedish, Norwegian, Danish, Finnish, Turkish, Croatian, Slovenian, Polish, Czech, Hungarian, Russian, Bulgarian, Greek, Slovak.

EXT2 Out

By pressing / select EXT2 Output.Use / button, to set Ext-2 Out to TV, DTV EXT1, FAV, YPbPr Audio or PC Audio. Note: When TV Source is set to HDMI, HDMI Audio setting will be available among EXT-2 Out options.

English - 22 -

Install Menu
gation buttons move the selected programme to the decided programme space and press the GREEN button again.

Delete

Program Table Program Band Channel Colour System
To delete a programme, press the YELLOW button. Pressing the YELLOW button again erases the selected programme from the programme list, and the programmes below shift one up.
APS (Auto Programming System)
When you press the BLUE button for APS, Auto Programming System Menu will appear on the Screen.

Auto Program

Country

Program Table

By pressing / button, select Program Table. Press to display Program Table.
WARNING! All Prestored Programs will be deleted

Ok Cancel

P01 P02 P03 P04 P05 P06 P07 P08 P09 P10
BBC 1 C 04 C 05 BBC 1 CH 4 BBC 2 C 04 C 07 C 12 C 15
P11 P12 P13 P14 P15 P16 P17 P18 P19 P20

S S S S S S S S S C

A.P.S. (Auto Programming System) Country
Press / button to select your country. If you want to exit from A.P.S. function, press the BLUE button. When you press OK or RED button for starting APS, all stored programs will be erased and the following screen will be displayed:

TV DTV EXT-1 EXT-2 EXT-2 S

Fine Tune

By pressing / button, select Fine Tune. Press / button to adjust the tuning.

Search

By pressing / button, select Search. Press / button to start program searching.You can also enter the desired frequency via digit buttons when search item is highlighted.
By pressing / button, select Store. Press or OK button to store the adjustments. Stored. will be displayed on the screen. In source menu, highlight a source by pressing / button and switch to that mode by pressing or OK button. Source options are; TV, DTV, EXT-1, EXT-2, EXT-2 S, FAV, S-VIDEO, HDMI, YPBPR and PC. Note: You can mark desired source options by pressing OK button. Therefore, when AV button is pressed, only the marked source options will be available.

Install menu in AV modes

The following screen appears in the install menu:

Colour System VCR Store

English - 24 -

PC Mode

Power off both Computer and Display before making any connections. Set your PCs resolution correctly before connecting to the TV. See the table on Appendix page. Use 15-pin display cable to connect a PC to the LCD TV. Note: PC menu will not be active for TV sets without a PC input.

H (Horizontal) Position

This item shifts the image horizontally to right hand side or left hand side of the screen. Select H Position item by using Use / / button. button to adjust the value.

V (Vertical) Position

This item shifts the image vertically towards the top or bottom of the screen. Select V Position item by using / button. Use / button to adjust the value.

Menu System in PC mode

Sound Menu/Feature Menu
The items in these menus are described at Sound & Feature Menu explained in Menu System.
Depending on the resolution and scan frequency that you input to the TV Set, you may see a hazy or noisy picture on the screen. In such a case you can use this item to get a clear picture by trial and error method. Use / button to adjust the value.

PC Picture Menu

By pressing / button, select the second icon. PC Picture menu appears on the screen. Brightness, Contrast and Colour Temperature adjustments in this menu are identical to adjustments defined in TV picture menu in MENU SYSTEM.

Dot Clock

Dot Clock adjustments correct interference that appear as vertical banding in dot intensive presentations like spreadsheets or paragraphs or text in smaller fonts. Use / button to adjust the value.

PC POSITION Menu

By pressing / button, select the sixth icon. PC POSITION menu appears on the screen.

Sound in PC mode

Connect the PCs Audio output to the TVs PC Audio In socket with an audio cable.

To select superimposed over the programme on the screen, press . Press once to enlarge top half of the page,press again to enlarge the bottom half of the page.Press again to revert normal size. To discover solutions on quiz and games press At times it is convenient to hold a page of text.Press to hold a page. The page will be held on screen until the button pressed again. To select subcode pages press .Subcode pages are subsections of long Teletext pages that can only be displayed on the screen one section at a time. Time information will be displayed on screen after pressing button.If the programme does not have teletext transmission, no information will be displayed. When button is pressed while in teletext mode, the screen will be splitted into two windows, one displaying the teletext and the other displaying the current channel. Press the button to exit from teletext. To exit text press . button or
Note: If the signal becomes insufficient, the teletext mode will be quitted.

English - 27 -

Fastext
Your TV supports the 1000 page Teletext system. When the page number of any of the 1000 pages in memory is entered, the system will not search for the requested page; instead it will display the page automatically. If the requested page is not in memory, the system will search for the requested page number and save the 1000 pages including the requested page into memory after finding it. Press the button to move the Teletext screen forward one page at a time. Press the button to move the Teletext screen backward one page at a time.
Connect Peripheral Equipment

High Definition

Your LCD Television is capable of displaying High Definition pictures from devices such as a High Definition Satellite Receiver or DVD Player. These devices must be connected via the HDMI socket or Component Socket. These socket can accept either 720p or 1080i signals. Note: When it is desired to watch HDMI source with a DVI to HDMI cable; in order to enable audio, Audio Input (which is located at the left side of the antenna input) is to be used to get DVI devices audio signals.

For Fastext

The subject-heading for the information may have a particular colour. Press an appropriate RED,GREEN, YELLOW orBLUE button in order to reach the relevant page quickly.

Via The Scart

The TV has 2 Scart sockets. If you want to connect peripherals (e.g. video, decoder, etc.) which have Scart sockets to the TV, you can use SCART socket of the TV. Note: If an external device is connected via the Scart sockets, the TV will automatically switch to AV mode. If both sockets are employed at the sime time, SCART 1 becomes the preferential.

TOP text

TOP text mode of operation will be activated automatically according to the transmission. If TOP text transmission is present, colour coded buttons will appear in status row. If TOP text transmission is not present, status row will not appear. The subject-heading for information may be located in colored box. In Top mode the -P/CH or P/CH+ commands will request the next or previous page respectively. If TOP text transmission is not available, in case of operation of these commands, wraparound occurs. For example page 100 appears to be one greater than page 199.

Via Aerial Input

If the device you want to connect does not have a Scart socket, you should connect it to the Aerial input of the TV. If the VCR is connected via Aerial input, it is suggested to use Programme 0.

Decoder

If you are subscribed to cable TV offers, the organisation will supply you a corresponding decoder unit to allow the programmes to be unscrambled. For further information consult your dealer.
Connect a decoder with an aerial socket to the TV
Connect the aerial cable.
Connect a decoder without an aerial socket to the TV
Connect the decoder to the EXTERNAL socket of TV with a RCA cable. Through the SCART/RCA socket of the decoder, you may attain a better display resolution.

TV And Video Recorder

Connect the aerial cables. Better picture quality can be obtained if you also connect a Scart cable to SCART sockets.

Playback NTSC

Connect NTSC VCR player to a Scart socket of the TV. Then, press the AV button to select EXT1 or EXT2.

English - 28 -

Copy Facility
Source selection for VCR recording. Select Feature menu. Select SCART 2 Out by pressing / button. For copying the picture that comes from the tuner, select SCART 1. Note :Scart-1 socket cannot be used as DTV output. Please use Scart-2 instead.

Care Of The Screen

Clean the screen with a slightly damp, soft cloth. Do not use abrasive solvents as they may damage the TV screen coating layer.

Poor Picture

Have you selected the correct TV system? Is your TV set or house aerial located too close to non-earthed audio equipment or neon lights, etc.? Mountains or high buildings can cause double pictures or ghost images. Sometimes you can improve the picture quality by changing the direction of the aerial. Is the picture or Teletext unrecognisable? Check if you have entered the correct frequency. The picture quality may degrade when two peripherals are connected to the TV at the same time. In such a case, disconnect one of the peripherals.