Pomona

General Purpose Passive Oscilloscope Probes Models 4550B, 5795A, 5800A, 5803A, 5806A, 5827A, 6049A, 6069A, 6265, 6266, SP150B
FEATURES: Pomonas latest design of Passive Oscilloscope probes feature a one piece (monolithic) design for robust probe life. Probe bandwidth ratings are specified as a system bandwidth. System bandwidth includes both probe and oscilloscope together as a system. The result is a probe frequency response that can essentially can be considered transparent. For ease of use, Readout Actuator for probe attenuation sensing and a Ground Reference switch are featured on some probe models. Full set a accessories are included with each probe. All probes meet IEC1010-2-031, 300V, CAT I
Model #: Attention: System Bandwidth (3dB) MHz.: 15/20/60 20/60 15/150 System Risetime ns 23.33/3.5 3.5 11.66 1.75 17.5/1.75 1.75 2.33 1.75 5.83 17.5/5.83 23.33/2.33 Compensation Range (pf.): 10-60 10-60 N/A 10-60 10-60 15-50 10-30 10-30 10-60 10-60 10-60 Voltage Max. (Note 2) 300 Input Res. (M ) 1/1/10 1/10 1/10 Input Cap. (pf.): 64/10.5 9.10 77/11.5 5.5 10.10.5 65/11 50/15 Readout Actuator Pin: Gnd. Ref.: X
4550B 5795A 5800A 5803A 5806A 5827A 6049A 6069A SP150B
X1/X10 X10 X1 X10 X1/X10 X100 X10 X10 X10 X1/X10 X1/X10
1.) Measurements based on 1M Ohm, 20 pf. Oscilloscope.
All dimensions are in inches. Tolerances (except noted):.xx =.02 (,51 mm),.xxx = .005 (,127 mm). All specifications are to the latest revisions. Specifications are subject to change without notice. Registered trademarks are the property of their respective companies. Made in USA

6/9/99 SY/EH/LS

Sales: 800-490-2361 Fax: 888-403-3360 Technical Assistance: 800-241-2060
PomonaACCESS 90474 (800) 444-6785 or (425) 446-6010 More drawings available at www.pomonaelectronics.com

Page 1 of 6

S:\Engineering \Release\DataSheets\FlukeDataSheet\d4550B-SP150B_6_01.doc
2.) Maximum probe input voltage is limited to the lesser of 300VDC (includes AC peak to 1.3MHz.) or on X1, to the driven equipments input rating. * Oscilloscope Model # 5827 has a cable length of 2.0 Meters.

Model #:

Attention:

6101A 6102A

X10 X10
System Bandwidth (3dB) MHz.: 150 250
System Risetime ns 2.33 1.4
Compensation Range (pf.): 10-30 10-30
Voltage Max. (Note 2) 300 300

Input Res. (M ) 10 10

Input Cap. (pf.): 10.5 10
Readout Actuator Pin: X X

Gnd. Ref.:

5809A 5812A
System Bandwidth (3dB) MHz.: 300 300
System Risetime ns 1.17 1.17
Compensation Range (pf.): 10-60 10-60

Input Cap. (pf.): 17 17

Readout Actuator Pin: X
1.) Measurements based on 1M Ohm, 20 pf. Oscilloscope. 2.) Maximum probe input voltage is limited to the lesser of 300VDC (includes AC peak to 1.3MHz.) or on X1, to the driven equipments input rating.

Page 2 of 6

Low Frequency Trimmer Adjustment: (Model 5800A is not adjustable) Low frequency response can be matched to the oscilloscope by adjusting the compensation trimmer on the head of the probe. 1.) Connect the probe to the oscilloscope and to a 1 KHz. Square wave source, the rise time should not exceed 10 microseconds (most oscilloscopes provide a probe compensation output). For X1/X10 probes, switch to the X10 position. 2.) Set the oscilloscope to display two to three cycles and two to six vertical divisions. 3.) Carefully adjust the trimmer tool to obtain the flattest tops to the square waves displayed on the oscilloscope, see illustrations.
High Frequency Trimmer Adjustment: (Models 5809A and 5812A only) The high frequency compensation has been preadjusted at the factory, however if adjustment is required, use the following procedure. 1.) Remove the compensation box cover located near the connector. Using the BNC adapter, connect the probe to a square wave generator operating between 10 to 100 KHz terminated into 50 ohms. The square wave generator rise time should be approximately.125 ns. Adjust each control until the leading edge of the waveform is as flat, square and horizontal as possible (see high frequency illustrations). 2.) Readjust the low frequency compensation if necessary.

Page 3 of 6

Replacement Accessory Kit Part Number: 6267
Pomona Oscilloscope to Probe Cross Reference:
Manf. B&K B&K B&K B&K B&K B&K B&K B&K Fluke Fluke Fluke Fluke Fluke Fluke Fluke Fluke Fluke Fluke Fluke Fluke Fluke Model Series 1422, 1443 2120, 2125, 2522 5020, 5024, 5034 5100, 1541B 90, 105 Series PM3050, PM3052 PM3055, PM3057 PM3065, PM3067 PM3070, PM3072 PM3092, PM33094 PM3208, PM3209 PM3335, PM3337 PM3350A, PM3352A PM3355, PM3357 PM3365A, PM3367A PM3375, PM3377 PM3382, PM3384 x1 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A 5800A x10 x1/x10 x6266 5827A 5827A 5795A 4550B 5827A 5827A 5827A 5795A 4550B 5827A 6049A SP150B 5827A 5827A 6006* & 6033 6035* 5827A 5827A 5795A 4550B 5827A 5795A 4550B 5827A 5803A 5806A 5827A 5827A 5827A 5827A 5827A 5795A 4550B 5827A 5795A 4550B 5827A 5795A 4550B 5827A