PROGRAMMABLE THERMOSTAT

OWNERS GUIDE

Seven Day Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Wallplate Model CT8602 Para obtener un documento con las instrucciones en espaol, por favor visite nuestro sitio de web a: www.honeywell.com/yourhome. Pour obtenir des notices techniques en franais, veuillez consulter notre site web www.honeywell.com/yourhome.

Honeywell CT8602

Table of Contents
Step 1. Prepare for Installation..... Step 2. Remove Old Thermostat.... Step 3. Mount thermostat Wallplate..... Step 4. Wire Wallplate Terminals.... Step 5. Install the Batteries..... Step 6. Set Fan Operation Switch..... Step 7. Mount the Thermostat..... Step 8. Customize Your Thermostat.... Step 9. Set the Clock..... Step 10. Programming..... Step 11. Operating Your Thermostat.... Step 12. Set the Fan and System Switches.... If You Have a Problem..... Smart Response Technology.... Wiring Diagrams..... U.S. Registered Trademark Copyright 2001 Honeywell Place Bar Code Here All Rights Reserved 22

69- 1532

Total comfort temperature management with Smart Response Technology.
Congratulations! You made a smart choice by purchasing your new Honeywell thermostat; the smart thermostat that; Keeps you comfortable by automatically calculating exactly when the furnace or air conditioning should go on to have the house at the desired comfort temperature by the time you wake up or return home. Saves the maximum amount of energy and money by automatically remembering to adjust the temperature when you leave home or go to sleep. Provides the ultimate in comfort and convenience. It comes preprogrammed. You can use the preprogrammed schedule, or set your own. This manual answers many of the questions that can arise as you become familiar and comfortable with your Honeywell thermostat the state of the art in home comfort controls. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.
If this thermostat is replacing a control that contains mercury in a sealed tube, do not place your old control in the trash. Contact your local waste management authority for instructions regarding recycling and the proper disposal of this control, or of an old control containing mercury in a sealed tube.

MERCURY NOTICE

MERCURY SWITCH
TYPICAL LOCATION OF A MERCURY SWITCH IN A THERMOSTAT

M10614

69-1532
SET WAKE TIMES INCREASE TIME SETTING AND SETPOINTS OR SCROLL FORWARD THROUGH INSTALLER SETUP AND SYSTEM TEST SET CURRENT DAY AND TIME
SET LEAVE TIMES AND SETPOINTS
SET RETURN TIMES AND SETPOINTS
INCREASE TEMPERATURE SETTING OR SCROLL FORWARD THROUGH INSTALLER SETUP OPTIONS DECREASE TEMPERATURE SETTING OR SCROLL BACKWARD THROUGH INSTALLER SETUP OPTIONS DISPLAY INFORMATION SUCH AS PRESENT SETTINGS AND OUTDOOR TEMPERATURE
RETURN TO NORMAL OPERATIONS ENTER INDEFINITE OR TIMED HOLD MODE
Run Program Set Current Day/Time Wake

Set Program

Leave Return Heat Off Sleep Cool
SET SLEEP TIMES AND SETPOINTS SYSTEM SWITCH

Hold Temp

Heat/Cool Settings

System On Auto

SET CURRENT OR PROGRAM DAY CHANGE BETWEEN DAYLIGHT SAVINGS AND STANDARD TIME

Daylight Time

FAN SWITCH
COPY ONE PROGRAMMED DAY TO ANOTHER DAY
DECREASE TIME SETTING OR SCROLL BACKWARD THROUGH INSTALLER SETUP AND SYSTEM TEST
CHANGE BETWEEN HEATING AND COOLING SETPOINTS M14880
SHOWS WHEN THERMOSTAT IS IN THE PROGRAMMING MODE SHOWS THERMOSTAT IS PROCESSING INFORMATION AND WAITING TO CALL FOR HEAT OR COOL SHOWS SMART RESPONSE IS CHANGING THE TEMPERATURE TO MEET THE CURRENT PROGRAMS SHOWS VACATION HOLD DURATION

DISPLAYS EITHER CURRENT TIME OF DAY OR PROGRAM TIMES SHOWS TEMPERATURE SETTING CHANGED FOR THIS PROGRAM PERIOD SHOWS THE TEMPERATURE DISPLAYED IS THE CURRENT SET TEMPERATURE SHOWS CURRENT SYSTEM SWITCH POSITION HEAT/OFF/COOL SHOWS THAT THERMOSTAT IS "CALLING" FOR HEAT OR COOL SHOWS SMART RESPONSE IS OFF. CONVENTIONAL RECOVERY IS ON
Wait Set Program Set Day/Time Temporary Setting Recovery Hold for

System Heat Off Cool

Days Mon Tue Wed Thu Fri Sat Sun Repl Batt Room Filter Wake Leave Return Sleep DST
SHOWS THE BATTERIES ARE LOW AND MUST BE REPLACED SHOWS SYSTEM ON DAYLIGHT SAVINGS TIME DISPLAYS EITHER ROOM OR SET TEMPERATURES SHOWS THE TEMPERATURE DISPLAYED IS THE CURRENT ROOM TEMPERATURE
SHOWS CURRENT DAY OR DAYS BEING PROGRAMMED SHOWS CURRENT PROGRAM PERIOD OR PERIOD BEING PROGRAMMED

M18746

STEP 1. PREPARE FOR INSTALLATION
Check Table 1, the compatibility chart, to make sure the thermostat is compatible with your system. If your system is not compatible, call Honeywell Customer Relations Center, toll-free, 1-800-468-1502.
Table 1. Compatibility Chart. System Type Gas Standing Pilot Gas Electronic Ignition Gas-fired Boilers Gas 750 Millivolt Heat onlyb Oil-Fired Boilers Oil-Fired Furnace Electric Furnace Electric Air Conditioning Baseboard Electric (120/240 line volt)c Single Stage Heat Pump Multistage Heat Pumps/Multistage Equipment
Compatibility with CT8602 Yes Yes Yesa Yes Yesa Yes Yes Yes No Yes No
Compatible with 2-wire Honeywell and Taco zone valves. Not compatible with 3-wire zone valves or 2-wire White Rodgers no. 1361 zone valves. Millivolt system must be heat only. Not compatible with any 120/240 volt system. Thermostat Wiring labels Screwdriver Drill 5 69-1532 Wallplate 3 Energizer AA batteries Screws and anchors Owners manual

Package Contents

Tools Required
STEP 2. REMOVE OLD THERMOSTAT
Test your heating and cooling systems to make sure they work properly. If either system does not work, contact your local heating/air-conditioning dealer. To avoid compressor damage, do not operate the cooling system when outdoor temperature is below 50F (10C). Turn off power to the system at the furnace or the fuse/circuit breaker panel. Carefully unpack your new thermostat and wallplate. Save package of screws, instructions, and receipt. Remove the cover from the old thermostat. If the cover does not snap off when pulled firmly from the bottom, check for a screw or screws used to lock on the cover. Loosen the screw or screws holding the thermostat to the wallplate and lift the thermostat away. Disconnect the wires from the old thermostat. As you disconnect each wire, attach the enclosed labels with the old terminal designation. If there are only two wires, they do not need to be labeled. Wrap the wires around a pencil as shown to keep them from falling back into the wall.

Special Installations

Read this section if you are replacing: Clock thermostat with separate wires for the clock. Thermostat with six or more wires connected to it. Thermostat in a heating only system with three wires.
WIRES THROUGH WALL OPENING
Replacing a Clock Thermostat that has C or C1 Clock Terminals
If you are replacing a Honeywell Chronotherm Thermostat, you may find one or two wires going to the C or C1 clock terminals on the Chronotherm wiring wallplate. Do not allow them to touch, or you can damage the transformer. Disconnect the wires and wrap them separately using electrical tape. Do not wrap them together. Place the wires where they will not interfere with the operation of the new thermostat. Record the colors and terminal designation labels of the remaining wires.
Replacing a Thermostat that has Six or More Wires
If there are six or more wires (excluding clock wires attached to terminals), you probably have a variation of a multistage heat pump or other multistage system. This thermostat is not compatible with multistage systems, so return the product to the place of purchase. If you have questions regarding this thermostat please visit our web site at www.honeywell.com/yourhome, or call the 24-hour automated information line at 1-800-468-1502.
Replacing a Thermostat that has Three Wires
If you have three wires for a heating only system and can operate the fan using the fan ON switch this thermostat works with your system. However, some hot water (zoned) heating systems also have three wires. Your thermostat will work only if you install an isolating relay on these systems. For details, call your local heating and/or cooling contractor. 6 69-1532
STEP 3. MOUNT THERMOSTAT WALLPLATE
Separate the wallplate from the thermostat by placing your thumb or fingers between the bottom of the wallplate and the thermostat, and pulling the wallplate up and away from the thermostat. See illustration at right. Position the wallplate on the wall. Level the wallplate for appearance if desired. Use a pencil to mark the two mounting holes that best fit the application. Remove the wallplate from the wall. Drill two 3/16 in. holes in wall (if drywall) as shown. For materials such as plaster or wood, drill 7/32 in. holes where marked. Gently, tap the (provided) anchors into the drilled holes until they are flush with the wall. Reposition the wallplate over the holes. Pull the wires through the wiring opening. Loosely insert mounting screws into each of the holes. Level the wallplate if desired. Thermostat functions properly when not level. Tighten mounting screws.

WALL WIRES THROUGH WALL

M16427

WALL ANCHORS (2)

MOUNTING HOLES MOUNTING SCREWS

M15044

STEP 4. WIRE WALLPLATE TERMINALS
IMPORTANT All wiring must comply with local codes and ordinances. If unsure about household wiring procedures, call your local heating/air-conditioning contractor. Refer to the labels you placed on the wires when you removed the old thermostat (see illustration). Match the letter of your old thermostat wire with the corresponding terminal letter on your new thermostat. Refer to Table 2. Remove the factory-installed jumper connecting terminals R and RC if wires are connected to both of those terminals. For wiring diagrams, if needed, see pp 22-23. Loosen the terminal screws. Slip each wire beneath its matching terminal. Wraparound and straight connections are both acceptable, (see illustration). Tighten the terminals.
FOR WRAPAROUND INSERTION STRIP 7/16 IN. (11 MM). FOR STRAIGHT INSERTION STRIP 5/16 IN. (8 MM).

M16425

Plug the hole in the wall with insulation to help prevent drafts from adversely affecting thermostat operation.
Table 2. Terminal Designations on Old and New Thermostats Terminal on Old Thermostat R, RH , 4, V Rc, Ra W, W1, H Y, Y1, M G, F O Bb Cc, Xc, Bb W2, H2 Y2
Connect To R Rc W Y G O Bb Do not connect. Do not continue installation. Call 1-800-468-1502. Power Power for cooling Heat Cooling Fan

Description

Changeover in cool. (Single stage heat pump only). Changeover in heat. (Single stage heat pump only). Transformer common Second stage heat. Second stage cool.
If both RH and R terminals are present on existing thermostat, remove jumper and connect Rh to R and R to Rc. Do not connect both O and B when wiring to a single stage heat pump. Connect O to O. Tape off B. c Tape off end of the wire with electrical tape and push the taped wire back into the wiring hole in the wall.
STEP 5. INSTALL THE BATTERIES

WALLPLATE

IMPORTANT Three AA alkaline batteries are included with the thermostat. Batteries must be installed for programming and operation of the thermostat and the heating/cooling system.
Install the batteries in the wallplate so the positive terminals all point up (see illustration). If the thermostat is already mounted on the wall, remove the thermostat by placing your thumb between the thermostat and wallplate and pulling the thermostat up and away as shown.

INSTALL 3 AA ALKALINE BATTERIES AS SHOWN, POSITIVE (+) TERMINALS TOWARD TOP.

M10622

When the batteries are running low, a REPL BAT message flashes for one to two months before the batteries run out completely. Replace the batteries as soon as possible once the message flashes. IMPORTANT Although the thermostat has a low battery indicator, replace the batteries once per year to prevent leakage and to prevent the thermostat and heating/cooling system from shutting down due to lack of battery power in the thermostat. If you insert new batteries within 20 to 30 seconds of removing the old batteries, the system retains the current time and day. If the display is blank, the batteries are dead or installed incorrectly. You must reset the time and day. Refer to Set the Clock for instructions.

M16424

As a precaution when leaving home for longer than a month, change batteries before leaving to prevent the system from shutting down due to lack of power. Always use fresh alkaline batteries. Nonalkaline batteries do not last as long. They also can leak, causing damage to the thermostat and the wall surface. Honeywell recommends Energizer batteries.
STEP 6. SET FAN OPERATION SWITCH
The thermostat fan operation switch, labeled FUEL SWITCH is factory set in the F position. This is the correct setting for most systems. If your system is an electric heat system, set the switch to E. The E setting allows the fan to turn on immediately with the heating and cooling in a system where the G terminal is connected.

FUEL SWITCH

M12676
STEP 7. MOUNT THE THERMOSTAT

A. ENGAGE TABS AT TOP

OF THERMOSTAT AND WALLPLATE.

B. PRESS LOWER

EDGE OF CASE TO LATCH.

M12703

STEP 8. CUSTOMIZE YOUR THERMOSTAT
Your Honeywell CT8602 thermostat comes preset to the most commonly used settings. The settings are: Gas or oil forced air furnace. Smart Response technology on. Temperature F. 12-hour clock format. You can change any or all of these settings. IMPORTANT Always press the keys with your fingertip or a similar blunt tool. Sharp instruments like pens and pencil points can damage the keyboard.
Press and hold down , , and , simultaneously until the screen shows. You now can change any of these settings.
System Type (Feature Number 4)
System type options are: 1 = Gravity or steam system. 3 = Hot water, high efficiency furnace (90% or better), or single stage heat pump. 6 = Gas or oil forced air furnace (preset). 9 = Electric furnace. To change your system type:

Press

FEATURE NUMBER OPTION

M18750

until display shows your furnace or boiler type. to move to next feature or

Run Program

Press Time
to return to main display.
Smart Response Technology (Feature Number 13)
Smart Response technology options are: 0 = Smart Response technology on (preset). 1 = Smart Response technology off. To turn Smart Response technology on or off:

M18751

once. to move to next feature or
See Smart Response technology (page 21) for information about this feature.
Temperature Format (Feature Number 14)
Temperature format options are: 0 = F (preset). 1 = C. To change temperature format:

M18752

Time Format (Feature Number 16)
Time format options are: 0 = 12-hour clock (preset). 1 = 24-hour clock. To change time format:

Press Press

M18753
Heating Temperature Range Stops (Feature Number 34)
Temperature range options are: 90 = highest setting for heating setpoint (preset) 40 to 89 = temperature range (1F increments) heating setpoint can be set to.

M18748

Cooling Temperature Range Stops (Feature Number 35)
Temperature range options are: 45 = lowest setting for cooling setpoint (preset) 46 to 99 = temperature range (1F increments) cooling setpoint can be set to.

M18749

Factory Set Function (Feature Number 37)
Do not change this setting.

STEP 9. SET THE CLOCK

Set Current Day and Time

M18754

On initial power-up, the screen flashes 1:00 pm until you press a key.

Set Current Day/Time Day

. until screen shows current day. until screen shows current time. (Tapping the

Set Current Day/Time

Press Time or hour increments).
will advance the time in one
until DST displays if daylight savings time is in effect.

STEP 10. PROGRAMMING

The keyboard is located behind the thermostat cover. The three most frequently used keys are near the display. Pressing displays the current temperature settings. Pressing the and keys change the temperature. The thermostat displays day, time, program period, temperature, system and fan settings. There is an individual key for each of the four program periods: Wake The program period when you want the house at a comfortable temperature when you get up and while you get ready for work or school. (This is a higher temperature during the heating season and a lower temperature during the cooling season). Leave The program period you can set for an energy-saving temperature while you are away at work or school. (This is a lower temperature during the heating season and a higher temperature during the cooling season). The program period when you want the house at a comfortable temperature for activities before bedtime. Return (This is a higher temperature during the heating season and a lower temperature during the cooling season). The program period you can set for an energy-saving temperature while you sleeping. (This is a lower Sleep temperature during the heating season and a higher temperature during the cooling season).

Table 3 can be helpful when planning your schedule of time and temperature settings. The thermostat default settings are shown in parentheses ( ). Table 3. Personal Programming Table. Period Wake Default Setting Time (6:00AM) Heata (70F/21C) Coolb (78F/25.5C) Leave Time (8:00AM) Heata (62F/16.5C) Coolb (85F/29.5C) Return Time (6:00PM) Heata (70F/21C) Coolb (78F/25.5C) Sleep Time (10:00PM) Heata (62F/16.5C) Coolb (82F/28C)

Monday (Mon)

Tuesday (Tue)
Wednesday Thursday (Wed) (Thu)

Friday (Fri)

Saturday (Sat)

Sunday (Sun)

Your heating setpoints cannot be higher than 90F (32C) or lower than 40F (4.5C). Your cooling setpoints cannot be higher than 99F (37C) or lower than 45F (7C).

Program the First Day

Start by programming the wake time and temperature for one day.

Press and release Press

Day Wake
until the desired day displays. (Mon, Tue, Wed, Thu, Fri, Sat, Sun) or until the desired time shows in the display. 15 69-1532

Press time

Program times are in 15 minute intervals. For example, 8:00, 8:15, 8:30. or until the desired wake temperature displays.
The setpoint temperature range is 40F to 90F (4.5C to 32C) for heating and 45F to 99F (7C to 37C) for cooling.
to switch between setpoints.
Program times are the same for heating and cooling. or until the display shows the desired temperature setpoint.

Return

Press Leave , programmed.
and repeat these steps for each program period. The First Day is now
Repeat each step in Program the First Day for the rest of the week.
After the first day is programmed, you can copy that day to any other day using procedure in Copy a Day.
when the entire week is programmed.

Copy a Day

Your thermostat can copy program settings from one day to another.

Press Press Press

to enter programming mode.
until the display shows the day you want to copy. The display shows.

M13327

until the display shows the day you want to copy to.

Mon Wed

M13328

to accept the change.

Repeat these steps for each day you want to copy.
donE appears for two seconds and then the normal program display appears.

M13329

Clear a Program Period

Wake cannot be cleared.

for the program period you want to clear.
until the desired day displays.

Press and hold the

for approximately 3 seconds until the time and temperature clear.
Repeat the above steps for each period to be cleared. Press
STEP 11. OPERATING YOUR THERMOSTAT

Change Temperature Setting Until the Next Program Period (Temporary Change)
until the screen shows the desired temperature setting.
The temporary temperature setting is displayed for about 3 seconds and then the room temperature is displayed. Temporary appears in the display. The setting cancels when the next program period starts or when you press

. 17 69-1532

Change Temperature Setting Indefinitely (Hold)
Move the System switch to the desired position (Heat or Cool). Press Hold Temp then or to change your setting if desired. (The display changes from showing the setpoint temperature to room temperature after approximately three seconds). To cancel Hold press
Change the Temperature Setting Until a Designated Day and Period (Vacation Hold)
twice. until the display shows the desired temperature setpoint. until the desired number of days that you will be away (1 through 255) is displayed. ,

Press Time Press

to select the program period when you want the program to restart.
If the Vacation Hold needs to be cancelled before the designated time, press program.

to return to the

Daylight Savings Time Key
This feature allows you to switch between standard time and daylight savings time.

Press Press time.

Daylight Time Daylight Time
during fall to set the time back one hour. during the spring to set time forward one hour. DST is displayed when operating on daylight savings
Pressing the Daylight Time key more than once in a five minute period scrolls you through various time option. For example, one hour earlier or later, with or without DST. Pressing Daylight Time six times in a five minute period returns you to your original setting.
STEP 12. SET THE FAN AND SYSTEM SWITCHES
First set the fan switch. Fan On: The fan runs continuously. Use for improved air circulation or for more efficient central air cleaning. (In a heat-only system, fan runs continuously only if fan relay is connected to the G thermostat terminal). Fan Auto: Normal setting for most homes. The equipment controls the fan operation. Then set the system switch. Heat: The thermostat controls your heating system.

On Fan

On Fan Heat System Off
Off: Both the heating and air conditioning systems are off.

Heat System

Cool: The thermostat controls your air conditioning system.

IF YOU HAVE A PROBLEM

Table 4. Solution Guide. If. Display does not appear. Then Make sure the batteries are installed correctly. Make sure the thermostat is mounted and latched on the wallplate. Mount and latch the thermostat on the wallplate if it is not. Make sure the temperature setpoints are: 40 to 90F (4.5 to 32C) for heating. 45 to 99F (7 to 37C) for cooling. Check Customize Your Thermostat section feature numbers 34 and 35. Reset as necessary. 19 69-1532

Temperature settings will not change (example; cannot set the heating higher or the cooling lower).
Table 4. Solution Guide. If. Heating does not come on. Cooling does not come on. System on indicator( = heat, = cool) is lit, but no warm or cool air is coming from the registers. Display flashes during programming. Then Make sure the heating setpoint is above the room temperature. Make sure the circuit breaker is not tripped, and reset it if necessary. Make sure the power switch at the equipment is in the On position, and set it to On if it is in the Off position. Wait five minutes for the system to respond. Set the system switch to Heat. Make sure the cooling setpoint is below the room temperature. Make sure the circuit breaker is not tripped, and reset it if necessary. Make sure the system switch at the air conditioner is in the On position, and set it to On if it is in the Off position. Wait five minutes for the system to respond. Set the system switch to Cool.
Wait five minutes after seeing the flame or snowflake and check the registers again. If no there is no hot or cool air coming from the registers, refer to Heating does not come on or Cooling does not come on. If all of this has been checked, contact your local heating and cooling contractor. The temperature setting limit has been reached. The heating setting range is 40F to 90F (4.5C to 32C). The cooling setting range is 45F to 99F (7C to 37C). 1. Check the program times for the period in question. 2. Make sure the AM and PM settings are correct. 3. Make sure the current time and day settings are correct. 4. Reprogram any incorrect settings. NOTE: If your thermostat is set for Smart Response technology, the start times occur before your programmed comfort periods. Wait until Replace Battery indicator is illuminated and replace batteries. Replace batteries now.
Temperature change occurs at the wrong times.
Thermostat backlight appears dim.
Toll-Free Customer Assistance
Please read and follow the provided instructions for this thermostat. If you have questions regarding this thermostat please visit our web site at www.honeywell.com/yourhome, or call the 24-hour automated information line at 1-800468-1502. Before calling, please have the following information available: Thermostat model number. (Located on back of thermostat). Thermostat date code. (Located below model number). Type of heating/cooling system (for example, hot water, warm air, oil, or gas). Location and number of wires connected to the thermostat.

SMART RESPONSE TECHNOLOGY
Your CT8602 is actually a small computer. The Smart Response technology calculates the correct time of day to turn on your heating or cooling system. Smart Response technology considers the following information. Air temperature. Wall temperature. The time of day when you want the comfort temperature established. When the thermostat activates Smart Response technology, the thermostat displays In Recovery, changes the setpoint, and turns on the system. Your CT8602 thermostat learns from experience. Each day it checks how closely it hit the recovery target and then adjusts the next days recovery start time accordingly. It takes a few days after installation for the thermostat to adjust to the local weather, your lifestyle, the construction of your home, and your heating/cooling system. You can turn off Smart Response technology by selecting Conventional Recovery. See Step 8. Customize Your Thermostat.
System Operating in Comfort Mode 68F Recovery Continues TEMPERATURE
AM AM Mon Wake System Heat Room
66F Recovery Begins 64F System Operating in Energy Savings Mode 62F
Mon Sleep System Heat AM Room AM Mon Sleep System Heat Heat In Recovery

Mon Sleep System Heat

Heat In Recovery
5:00 ENERGY SAVINGS PERIOD

6:30 COMFORT PERIOD

RECOVERY FROM ENERGY SAVINGS TIME
THERMOSTAT USES THE SAME SCHEME TO RETURN TO LOWER COMFORT TEMPERATURE DURING THE COOLING SEASON. 1 IF In Recovery IS DISPLAYED, PRESS TO SEE THE COMFORT SETPOINT.

M18591

WIRING DIAGRAMS
2-WIRE HEAT-ONLY (JUMPER INTACT)
THERMOSTAT B RC O W Y R G
4-WIRE HEAT/COOL (JUMPER INTACT)
HEATING RELAY OR VALVE COIL

COOLING CONTACTOR COIL

FAN RELAY
1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

M10616

M10617
4-WIRE SINGLE-STAGE HEAT PUMP (JUMPER INTACT)
THERMOSTAT B RC O W Y R G 3
3-WIRE HEAT ONLY WITH FAN (JUMPER INTACT)
2 COMPRESSOR CONTACTOR FAN RELAY HEAT CHANGEOVER VALVE

COOL CHANGEOVER VALVE

M10618
POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. USE EITHER O OR B FOR HEAT PUMP CHANGEOVER. USING A JUMPER WIRE (NOT SUPPLIED) CONNECT W TO Y.

M12739

5-WIRE HEAT/COOL (JUMPER REMOVED)
5-WIRE HEAT/COOL WITH DAMPER (JUMPER INTACT)
HEATING RELAY OR VALVE COIL 1

COOLING CONTACTOR COIL 1

HEAT DAMPER

HEAT RELAY

COMPRESSOR CONTACTOR
COOL DAMPER 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD M10619 PROTECTION AS REQUIRED.

M18738

Notice:
This thermostat is a Class B digital apparatus that complies with Canadian Radio Interference Regulations, CRC c. 1374.

Limited One-Year Warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywells option) within a reasonable period of time. If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the retailer from which you purchased it, or (ii) package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and mail it, postage prepaid, to the following address: Honeywell Return Goods Honeywell Canada: Dock 4 MN10-3860 Honeywell Limited/Honeywell Limite 1885 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Honeywells sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Customer Assistance, Honeywell, 1885 Douglas Drive North, Golden Valley, MN 55422-4386. In Canada, write Retail Products ON30 Honeywell Limited/Honeywell Limite, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.
Home and Building Control Home and Building Control
Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limite 35 Dynamic Drive Scarborough, Ontario M1V 4Z9
Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.

69-1532 J.H. 04-01

www.honeywell.com/yourhome

CT3600, CT3611, CT3500, CT3595, CT8602 Thermostats

OWNERS GUIDE ADDENDUM

FURNACE AIR FILTER, HUMIDIFIER PAD AND ULTRAVIOLET (UV) LAMP TIMERS
Your thermostat has up to three timers that remind you to change or clean your furnace air filter, whole-house humidifier pad or UV (ultraviolet air treatment system) lamp.
Humidifier Pad Timer (Feature No. 44)
Humidifier pad timer options: 0 = off 1 = 90 days 2 = 180 days 3 = 365 days

M20246

Customize Your Timers (See Owners Guide for Instructions on Entering Customize Mode)
Furnace Air Filter Timer (Feature No. 43)
Filter timer options: 0 = off 1 = 30 days 2 = 90 days (preset) 3 = 180 days 4 = 365 days
To change your humidifier pad timer: Press until display shows the desired number of days. Press Time to move to next feature or press Run Program to return to main display. NOTE: The humidifier pad time is based on calendar days. See your humidifier instructions for complete details on replacing and/or cleaning your humidifier pad.
Ultraviolet (UV) Lamp Timer (Feature No. 45)
UV lamp timer options: 0 = off (preset) 1 = 365 days

OPTION

M20245 M20247

FEATURE NUMBER

To change your filter timer: Press until display shows the desired number of days. Press Time to move to next feature or press Run Program to return to main display. NOTE: The filter time is based on calendar days.
To change your UV lamp timer: Press until display shows the desired number of days. Press Time to move to next feature or press Run Program to return to main display. NOTE: The UV lamp time is based on calendar days. See your UV lamp instructions for complete details on replacing your UV lamps.
U.S. Registered Trademark Copyright 2002 Honeywell

All Rights Reserved

69-1583-1
CT3600, CT3611, CT3500, CT3595, CT8602 THERMOSTATS
View or Reset Timer Settings
When the thermostat activates a timer, the thermostat flashes Filter until the timer resets. 1. Reset the timer by pressing the i key until the expired timer is displayed.
Press the time key to reset the timer.

Filter

M20244
Press the Run Program key.

M20243

NOTE: You can view the number of days remaining at any time by pressing the i key three or four times. If more than one timer is active, all active timers show sequentially when pressing the i key several times. For complete instructions on replacing or cleaning your furnace filter, humidifier pad or UV lamp, see the product owners manuals. Contact your local contractor or visit www.honeywell.com/yourhome.
Automation and Control Solutions
Honeywell 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limite 35 Dynamic Drive Scarborough, Ontario M1V 4Z9

69-1583-1 G.H. Rev 05-02

Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.
www.honeywell.com/yourhome