In todays always-on world, lifestyles are BECOMING increasingly digital. Volumes of digital photos, music, and videos are stored ON multiple PCs and shared through the Internet, networks, and online applications. So how do you begin living the digital life? What do you need to make the transformation, and why will it make your life easier?
HP believes passionately in making it simple and easy for you to adopt and manage a high-definition lifestyle. Whether at home or on the go, you can experience your movies, photos, music, videos, and more. Thats why in 2007 HP brought to life HP SmartHome a real-life home that demonstrates an affordable and compelling digital experience. The home shows how you can easily enjoy your favorite digital media and manage home life conveniences with complete personalization using a range of products that are readily available in todays market. The HP SmartHome is built on the fundamental principle of open standards. HP has also partnered with some of the biggest industry brands to deliver an end-to-end digital experience. From distributed audio to lighting control to intelligent applianceseverything is seamlessly and easily integrated in the house.
With the HP SmartHome, HP SHOWS YOU HOW EASY IT IS to START LIVING THE digital life.

HP SmartHome

Cupertino, CA
Go to hp.com or visit your local retail store to purchase these HP SmartHome products.
MASTER BEDROOM MEDIA CLOSET

TEENAGERS ROOM

UTILITY ROOM KITCHEN

DINING ROOM LIVING ROOM

OFFICE

L I V I N G Ro om

U tility Ro om

home control

HP SL4778N 47" diagonal 1080p MediaSmart LCD HDTV HP w1907 19" diagonal Widescreen Flat-Panel Monitors (3) Dish Network VIP622 DVR Satellite Dish Receiver Denon AVR 2805 AV Surround Receiver Microsoft Xbox 360 Elite with 120GB hard drive Monster Cable AVL 300 Universal Remote Control Bravo D2-DV 228 Digital Media Player
Lutron Homeworks 8 series Processor & Remote Dimming Panel Lighting System

appliances

Klipsch RVX-42 LCR Front Speakers Klipsch RSX-3 Rear Surround Sound Speakers Russound RNET UNO-S1 Audio Keypad Russound ComPoint ISK2 Intercom Keypad
Whirlpool Duet HT WFW9400SZ00 Ultra Capacity Plus Front Load Washer Whirlpool Duet WED9400S Super Capacity Plus Electric Dryer

Office

Life|ware 8.9" diagonal Life|point Touchscreen Panel Lutron Homeworks SeeTouch Light Keypad Graber Cellular Shades controlled by Z-Wave Technology

M ED I A Closet

Klipsch Klipsch Klipsch Klipsch
RSX-5 Front Channel Speakers RCX-5 Center Channel Speaker R-5650W In-Wall Surround Speakers RW-12 12" Subwoofer
Life|ware 12" diagonal Life|point Touchscreen Panel Lutron Homeworks SeeTouch Light Keypad Graber Cellular Shades controlled by Z-Wave Technology

D ining Ro om

HP Pavilion Elite m9100z series Desktop PC HP Pavilion Slimline s3000 Desktop PC HP w2207h 22" diagonal Widescreen Flat-Panel Monitor HP w2408h 24" diagonal Vivid Color Widescreen Flat-Panel Monitor HP Pavilion tx2000z series Convertible Notebook PC HP Officejet Pro L7650 All-in-One Printer HP 160GB Pocket Media Drive* HP Photosmart R967 10MP Digital Camera
HP LP3065 30" Widescreen Flat-Panel Monitor
Klipsch R-5650W In-Wall Speakers Russound RNET UNO-S2 Audio Keypad
Klipsch R-5650W In-Wall Speakers Klipsch ProMedia 2.1 THX Multimedia Computer Speaker System Russound RNET UNO-S2 Audio Keypad
HP Digital Entertainment Center z565 HP MediaSmart Server 2.5TB HP Media Vault mv2120 (500GB) HP Pavilion Slimline s3000 Desktop PC HP w2207h 22" diagonal Widescreen Flat-Panel Monitor HP w1907 19" diagonal Widescreen Flat-Panel Monitor HP ProCurve 2810 series 48-port 10/100/1000 Switch Russound RNET CAM 6.6 Multi-Zone Receiver/ Controller D-Link DIR-655 Wireless-N Router UStec PROLAN 16 tecCenter Structure Wiring Cabinet Middle Atlantic 19" AV Equipment Rack
Lutron Homeworks SeeTouch Light Keypad Graber Cellular Shades controlled by Z-Wave Technology
Klipsch R-2650-CSM In-Ceiling Stereo Speaker

K itchen

T EEN AG ER S Ro om
HP TouchSmart IQ775 Desktop PC HP w2207h 22" diagonal Widescreen Flat-Panel Monitor
HP LC3772N 37" diagonal Widescreen LCD HDTV HP Blackbird 002 Gaming PC Microsoft Xbox 360 Premium Gaming System Dish Network VIP211 HD Satellite Dish Receiver
Lutron Homeworks SeeTouch Light Keypad Graber Cellular Shades controlled by Z-Wave Technology AprilAire HVAC Controller Russound Doorbell Controller

P O RCH

Klipsch R-5650W In-Wall Surround Speakers Russound RNET UNO-S1 Audio Keypad Russound ComPoint ISK2 Intercom Keypad

Klipsch ProMedia Ultra 5.1 Speaker System
Panasonic Camera BB-HCM 331
Klipsch AW-650 Outdoor Speakers

Master B edro om

Whirlpool Gold GD5NHA 25.5 cu. ft. Side-by-Side Refrigerator w/centralpark Digital Photo Frame Whirlpool Gold GU2700XTSS Built-In Tall Tub Dishwasher Whirlpool Gold GY398LXP 30" Slide-In Electric Ceramic Glass Range Whirlpool Gold GH6177XPS 1.7 cu. ft. SpeedCook Microwave Oven TMIO PS302SS00 30" Internet-Connected Refrigerated Dual Wall Oven
HP SL4278N 42" diagonal 1080p MediaSmart LCD HDTV HP MediaSmart Connect Dish Network VIP622 DVR Satellite Dish Receiver HP Pavilion HDX Entertainment Notebook PC Yamaha R-2300 AV Receiver Monster Cable AVL 300 Universal Remote Control HP DF800B Digital Photo Frame
I n t e g r a tio n p rovid e d by c y b e rM a n o r. Fu r nishin g s p rovid e d by A r t h u r M c L a u g h lin & A s s o cia t e s.
* When referring to hard drive capacity,1GB = 1 billion bytes. Actual formatted capacity is less. Copyright 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft is a U.S. registered trademark of Microsoft Corporation. Printed in the United States. 4AA1-9474ENUC; 04/2008

Upgrading and Servicing Guide
The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HP. Hewlett-Packard Company P.O. Box 4010 Cupertino, CA 95015-4010 USA Copyright 2007 Hewlett-Packard Development Company, L.P. May be licensed in the United States by one or both of U.S. Patents Nos. 4,930,158 and 4,930,160 until August 28, 2008. HP supports lawful use of technology and does not endorse or encourage the use of our products for purposes other than those permitted by copyright law. The information in this document is subject to change without notice.

Table of Contents

Introduction...1 Safety Information...2 Opening the Computer....2 Preparing the Computer...3 Removing the Computer Cover...4 Locating Components Inside the Computer..5 Closing the Computer...7 Replacing the Computer Cover...7 After Closing the Computer...7 Removing and Replacing an Optical Disc Drive...8 Before You Begin....8 Removing an Optical Disc Drive...9 Replacing an Optical Disc Drive..11 Removing and Replacing a Hard Disk Drive..12 Before You Begin...12 Removing a Hard Disk Drive....12 Replacing a Hard Disk Drive....14 Removing and Replacing Memory...16 Before You Begin...16 Removing a Memory Module...17 Replacing a Memory Module...18 Removing and Replacing a PCI Card..19 Before You Begin...20 Removing a PCI Card....20 Replacing a PCI Card...21 Removing a PCI-E Card...22 Replacing a PCI-E Card...23 Removing and Replacing the Battery...24 Before You Begin...24

Introduction

The Upgrading and Servicing Guide provides instructions on how to remove and replace the following hardware components in your HP Pavilion Slimline Desktop PC: Optical disc drive Hard disk drive Memory module PCI card PCI-E card Battery

Safety Information

Please read the following important safety information before performing any procedure. This product has not been evaluated for connection to an IT power system (an AC distribution system with no direct connection to earth, according to IEC 60950).
WARNING: Please read Additional Safety Information in your Limited Warranty and Support Guide before installing and connecting your system to the electrical power system.
WARNING: Keep your hands away from the moving fan. Keep fingers and tools clear of the fan when power is applied. Never open the cover with the power cord attached or power applied. You may damage your computer or be injured from the spinning fan blades.
WARNING: Avoid touching sharp edges inside the computer.

Opening the Computer

Before you upgrade any component in your computer, prepare the computer so that you can safely handle the unit and the components. Read the following items before attempting to upgrade or service the computer: Print out this document before attempting any removal/replacement procedures. These procedures assume familiarity with the general terminology associated with computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment. Write down and save the system model number and serial number, all installed options, and other information about the system. If you need this information later, you will not need to open and examine the computer.
CAUTION: Static electricity can damage the electronic components of the computer or optional equipment. Ensure that you are discharged of static electricity by briefly touching a grounded metal object.
Hewlett-Packard recommends that you use an antistatic wrist strap and a conductive foam pad when working on system electronic components. You need a Phillips screwdriver.

Preparing the Computer

To avoid injury and equipment damage, always follow this procedure before opening the computer: 1 Remove any of the following: Memory card from the memory card reader Optical disc (CD or DVD) from the optical drive Pocket Media Drive from the Pocket Media Drive bay 2 Turn off the computer. Click the Windows Start Button, click the Arrow button next to the Lock button, and then click Shut Down. 3 Disconnect the modem/telephone cable, if present.
WARNING: Always disconnect the modem cord from the telephone system before opening the cover.
4 Disconnect the power cord from the electrical outlet and then from the computer.
WARNING: To reduce the risk of personal injury from electrical shock or hot surfaces, disconnect the power cord from the electrical outlet. Then disconnect the computer from the power source before removing the computer cover. Failure to do so before you open the computer or do any procedures can result in personal injury or equipment damage.
5 Disconnect all other attached cables (such as the keyboard, mouse, Ethernet, and monitor). 6 Disconnect all external devices.
Removing the Computer Cover
WARNING: Remove power before opening the computer cover. Allow the internal system components to cool before touching.
1 Complete the procedure Preparing the Computer on page 3. 2 Lay the computer flat. 3 Loosen the three screws on the back cover. Use a Phillips screwdriver.

4 Slide the computer cover back about 1.25 centimeters (1/2 inch), and then lift it off the computer. Set it aside.

digi tal aud OUT io

wire less ante LAN nna

S-VI DEO

NOTE: Use the screwdriver slot on the back of the cover to loosen the cover, as required.
Locating Components Inside the Computer
Computer component configurations vary by model. You can remove and replace the following components: Component A Optical disc drive. May be a CD-ROM, CD-RW, DVD-ROM, DVD+RW, or combination drive Hard disk drive (located under the optical drive bay) Memory module (2) Modem card (PCI card) and graphics card (PCI-E card) Battery See: Removing and Replacing an Optical Disc Drive on page 8.

B C D E

Removing and Replacing a Hard Disk Drive on page 12. Removing and Replacing Memory on page 16. Removing and Replacing a PCI Card on page 19. Removing and Replacing the Battery on page 24.
Read the Before You Begin section at the start of each component procedure. This section contains requirements and important information about the replaceable component.
The following illustration shows component locations:
dig ita l OUau wi T dio reless an ten LA na N S-V IDE

Closing the Computer

Replacing the Computer Cover
1 Place all cables inside of the computer case. 2 Place the cover onto the computer about 2.5 centimeters (1 inch) back. Make sure the slots in the computer case align with the cover tabs. 3 Slide the cover forward on the frame until it locks into place. Make sure the bottom of the cover lines up with the computer case.
4 Align the screws on the computer cover with the holes on the back of the computer frame. Insert and then tighten the screws on the cover. 5 Complete the procedure After Closing the Computer on page 7.
After Closing the Computer
To avoid injury and equipment damage, always follow this procedure in this order after closing the computer:
WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug telecommunications or telephone connectors into the Ethernet network interface connector.
1 Reconnect the modem/telephone cable and all other attached cables, such as the keyboard, mouse, Ethernet, and monitor cables. 2 Reconnect external devices, such as a printer. 3 Reconnect the power cord. 4 Turn on the computer and all peripherals, such as the monitor.
Removing and Replacing an Optical Disc Drive
Your computer includes an optical disc drive that you can replace or upgrade. See Locating Components Inside the Computer on page 5.

Before You Begin

Observe the following requirements before removing and replacing the component: IMPORTANT: Due to the small computer size, you can only install an optical disc drive of less than the approximate length of 170 millimeters (6.7 inches).

Optical disc drive

Your computer comes with a SATA (serial advanced technology attachment) drive that uses a narrow data cable with an optional latch. This procedure requires a Phillips screwdriver.
Removing an Optical Disc Drive
1 Prepare the computer and remove the computer cover. Complete the Opening the Computer procedures on page 2. 2 Remove the front cover from the computer. Press the two tabs apart at the bottom of the cover, and press the two tabs together at the top of the cover; then push the cover out.

ita l au OU dio T

wirel aness tenLA naN
3 If your computer includes a Pocket Media Drive, lift the tab on the Pocket Media Drive cage. Then pull the cage back and out of the chassis.
4 Make a note of each cable and plug orientation attached to the back of the optical disc drive before removing the cables. 5 Disconnect the power cable and then the data cable from the back of the optical disc drive. Pull the tab on the data cable. Use a gentle rocking motion on the power cable.
NOTE: The SATA data cable may include a latch. Press the latch, and pull the plug to remove the data cable from the drive.
CAUTION: Pull the connector by the handle only.
6 Disconnect the sound cable, if present. 7 Remove the screw from the optical disc drive side. 8 Pull the latch away from the drive, and push the drive through the front of the computer. IMPORTANT: Do not tilt the drive during removal.
Replacing an Optical Disc Drive
1 Complete the procedure Removing and Replacing an Optical Disc Drive on page 8. 2 Gently push the new optical disc drive into the slot on the front of the chassis. 3 Insert the screw on the side of the optical disc drive. 4 Connect the power cable and data cable firmly to the back of the optical disc drive. Ensure that the cables are completely inserted. 5 Some drive models may have a sound cable. If so, connect the sound cable. 6 If your computer includes a Pocket Media Drive, insert the Pocket Media Drive cage: a Align the arrow on the PMD cage with the arrow on the bottom of the chassis. Push the PMD cage toward the front of the chassis until it locks in place.
7 Replace the front cover. 8 Replace the computer cover and close the computer. Complete the Closing the Computer procedures on page 7.
Removing and Replacing a Hard Disk Drive

Your computer includes a hard drive that you can replace or upgrade. See Locating Components Inside the Computer on page 5. The original hard disk drive is preloaded with the computer system recovery partition. If you remove this hard disk drive, store it in a properly sealed antistatic bag. The hard disk drive is a SATA (serial advanced technology attachment) drive that uses a narrow data cable with an optional latch.

Hard disk drive

Observe the following requirements before removing and replacing the component:
CAUTION: Before you remove the hard disk drive, back up your personal files on the hard disk drive to an external storage device, such as a DVD, CD, or USB drive. Failure to do so will result in data loss. After you replace the hard disk drive, perform the System Recovery procedure. Use the recovery discs to load the factory-installed files. Refer to the Troubleshooting and Maintenance Guide for detailed System Recovery steps.
IMPORTANT: Before upgrading a hard disk drive, make sure a recovery disc is available. This procedure requires a Phillips screwdriver.
Removing a Hard Disk Drive
1 Prepare the computer and remove the computer cover. Complete the Opening the Computer procedures on page 2. 2 If your computer includes a Pocket Media Drive, lift the tab on the Pocket Media Drive cage. Then pull the cage back and out of the chassis.
3 Make a note of each cable attached to the hard disk drive before removing the cables. 4 Lift the wire latch, and disconnect the power and data cables from the back of the hard disk drive. 5 Remove the retaining screw from the drive tray.
CAUTION: Handle hard disk drives with care. Dropping or banging the hard disk drive can result in data loss.
6 Slide the hard disk drive tray out of the drive bay by pulling the tab on the drive tray. NOTE: Ensure that the computer cables are clear of the drive tray when removing. Push them away, as required, before removing the tray. 7 Remove the four screws that secure the hard disk drive to the drive tray, and slide the hard disk drive out of the tray.
Replacing a Hard Disk Drive
1 Complete the procedure Removing a Hard Disk Drive on page 12. 2 Slide the hard disk drive into the tray. 3 Insert and tighten the four screws that secure the hard disk drive to the drive tray. 4 Slide the hard disk drive tray into the computer drive bay.

5 Insert and tighten the hard disk drive retaining screw into the drive tray.
6 Attach the data and power supply cables to the back of the hard disk drive and close the wire latch. 7 If your computer includes a Pocket Media Drive (PMD), insert the Pocket Media Drive cage: a Align the arrow on the PMD cage with the arrow on the bottom of the chassis. Push the PMD cage toward the front of the chassis until it locks in place.
8 Complete the procedures to replace the computer cover and close the computer. See Closing the Computer on page 7. 9 Perform a System Recovery, as required. Use the recovery discs to replace the factory-installed files. Refer to the Troubleshooting and Maintenance Guide for detailed System Recovery procedures.
Removing and Replacing Memory
The motherboard contains one or two memory module sockets for DDR DIMMs (double data rate dual in-line memory modules).
Observe the following requirements before removing and replacing the component: To determine which type and speed of memory module your computer uses, and for specific memory module information and specifications: 1 Go to http://www.hp.com/support in your Web browser. 2 Select your country/region and language. 3 From the Support and Drivers page, click See support and troubleshooting information, enter the model number of your computer, and then click Search.

Memory module

WARNING: Using the wrong type of memory module could damage the system.
WARNING: Handle the memory module with care. Be careful to not touch any memory module contacts. Touching the gold contacts may damage the module. Avoid touching the memory chips.

Removing a Memory Module

1 Remove the optical disc drive. See Removing an Optical Disc Drive on page 9. 2 Locate the memory socket on the motherboard.
3 Move any cabling out of the way, if necessary.
WARNING: Do not pull the memory module out of the socket. Use the retaining clips to eject the module.
4 Push down the two retaining clips on the ends of the socket until the memory module pops out of the socket. Hold the memory module by its edges only, as you lift it away from the socket.
5 Store the memory module in antistatic packaging.
Replacing a Memory Module
Upgrade the memory in your computer with memory of the same type and speed as the memory originally installed in your computer. 1 Complete the procedure Removing a Memory Module on page 17. 2 Open both latches of the memory module socket.
3 Remove the new memory module from the antistatic packaging. Hold it by its edges only. 4 You can install the memory module in only one position. Match the notch (A) on the memory module with the tab (B) on the memory socket. Push the module carefully and firmly into the slot, ensuring that the latches on both ends snap into place.

5 Repeat steps 1 to 4 for the second memory slot, as required. 6 Replace any cabling that was moved. 7 Complete the procedures to replace the optical disc drive. See Replacing an Optical Disc Drive on page 11.
Removing and Replacing a PCI Card
Your computer comes with a modem card in the PCI card slot. The computer may also come with a graphics card in a PCI Express (PCI-E) card slot. You can replace these cards with a new modem card or graphics card. You may also replace with a different PCI card or PCI-E card. The modem card is a telephone modem circuit board that fits into a PCI card slot.

Modem PCI card

Graphics PCI-E card
Observe the following requirements before removing and replacing the component: IMPORTANT: Due to the small computer size, you can only install a small, low-profile PCI card of the same approximate size of the modem card. HP recommends that you install a card with power consumption of 5 watts or less. Not all low-profile cards will fit into the PCI slot. Some external connectors, especially connectors located at the top of the card, may not fit properly into the back panel. IMPORTANT: Due to the small computer size, you can only install a small, low-profile PCI-E card of the same approximate size of the graphics card. HP recommends that you install a card with power consumption of 25 watts or less. Not all low-profile cards will fit into the PCI-E slot. Some external connectors, especially connectors located at the top of the card, may not fit properly into the back panel. This procedure requires a Phillips screwdriver.

Removing a PCI Card

1 Prepare the computer and remove the computer cover. Complete the procedures Opening the Computer on page 2. 2 Inside the computer, locate the PCI card slot on the motherboard. 3 Make a note of any internal cables attached to the card, and then disconnect them. 4 Remove the screw on the modem card bracket holder on the outside of the frame. Remove the bracket holder. 5 Hold the card at the top, and carefully pull the card straight out of the slot.

Replacing a PCI Card

IMPORTANT: Due to the small computer size, you can only install a small, low-profile PCI card of the same approximate size of the modem card. HP recommends that you install a card with power consumption of 5 watts or less. Not all low-profile cards will fit into the PCI slot. Some external connectors, especially connectors located at the top of the card, may not fit properly into the back panel. You can replace the modem card with a new modem card or another PCI card in the PCI card slot: 1 Complete the procedures to remove the modem card. See Removing a PCI Card on page 20. 2 Align the edge of the add-in card with the slot on the computer, and gently but firmly press the card straight down into the card slot. The whole connector should be seated properly in the card slot. 3 Attach the bracket holder with the screw to secure the card. 4 Connect any internal cables attached to the card. 5 Complete the procedures to close the computer. See Closing the Computer on page 7. 6 Install any software drivers supplied by the card manufacturer if you are installing another PCI card or as required. NOTE: If the new card or device isnt working, read the card manufacturers installation instructions, and recheck all connections, including those to the card, power supply, keyboard, and monitor.

Removing a PCI-E Card

1 Prepare the computer and remove the computer cover. Complete the procedures Opening the Computer on page 2. 2 Inside the computer, locate the PCI-E card slot on the motherboard. 3 Make a note of any internal cables attached to the card, and then disconnect them. 4 Remove the screw on the modem card bracket holder on the outside of the frame. Remove the bracket holder. 5 While lifting the latch holding the card to the motherboard, hold the card at the top, and carefully pull the card straight out of the slot.

Replacing a PCI-E Card

IMPORTANT: Due to the small computer size, you can only install a small, low-profile PCI-E card of the same approximate size of the graphics card. HP recommends that you install a card with power consumption of 25 watts or less. Not all low-profile cards will fit into the PCI-E slot. Some external connectors, especially connectors located at the top of the card, may not fit properly into the back panel. You can replace the graphics card with a new graphics card or another PCI-E card in the PCI-E card slot: 1 Complete the procedures to remove the graphics card. See Removing a PCI-E Card on page 22. 2 Align the edge of the add-in card with the slot on the computer, and gently but firmly press the card straight down into the card slot. The whole connector should be seated properly in the card slot. 3 Attach the bracket holder with the screw to secure the card. 4 Connect any internal cables attached to the card. 5 Complete the procedures to close the computer. See Closing the Computer on page 7. 6 Install any software drivers supplied by the card manufacturer if you are installing another PCI-E card or as required. NOTE: If the new card or device isnt working, read the card manufacturers installation instructions, and recheck all connections, including those to the card, power supply, keyboard, and monitor.
Removing and Replacing the Battery
A lithium battery on the motherboard provides backup power for the computers timekeeping capability. When the battery starts to weaken, the date and time may be incorrect. If the battery fails, replace it with a CR2032 lithium battery (3-volt, 220 mAh rating) or an equivalent battery.

WARNING: There is danger of explosion if the battery is incorrectly replaced. Replace only with the same, or equivalent, type of battery. Discard used batteries according to the manufacturers instructions.
WARNING: Never use metal objects, such as pliers, to remove or replace the battery. Metal contact may cause a battery short and damage the battery.

Procedure

1 Prepare the computer, and remove the computer cover. Complete the procedures Opening the Computer on page 2. 2 Gently lay the computer on its side. 3 Complete the procedure Removing an Optical Disc Drive on page 9. 4 Remove any cabling, if necessary, to reach the battery. 5 Move the retaining clip away from the battery. Lift the battery from the socket to release the battery.
6 Install the new CR2032 battery in the socket, with the positive (+) side facing the open side of the socket.
7 Replace all cables that you removed. 8 Complete the procedure Replacing an Optical Disc Drive on page 11. 9 Complete the procedures to replace the computer cover and close the computer. See Closing the Computer on page 7. NOTE: You may have to manually set the time and date on the computer after startup.

Part number: 5991-8366