The server includes an integrated, nonvolatile management log that contains fault and management information. The contents of the Integrated Management Log (IML) can be viewed with Insight Manager.

Telephone Numbers

For the name of the nearest HP authorized reseller: In the United States, call 1-800-345-1518. In Canada, call 1-800-263-5868.
For HP technical support: In the United States and Canada, call 1-800-652-6672. Outside the United States and Canada, refer to

www.hp.com

Illustrated Parts Catalog
This chapter provides the illustrated parts breakdown and a spare parts list for the HP ProLiant DL760 server. Refer to the table following each illustration for the names of referenced spare parts.

System Chassis

Figure 1-1: System chassis exploded view
Table 1-1: System Chassis Spare Parts List
Item Description Spare Part Number
System Chassis 1 System 2 I/O Media Heatsink Ramp* Memory module bezel* 5 I/O module with PCI-X I/O board 339661-001 lid Processor and memory module (without processors) module * chassis 122214-001 278466-001 319945-001
System Components Hot-plug power supply 1150 W System midplane assembly 122235-001 316747-001

*Not shown

Media Module
Figure 1-2: Media module exploded view
Table 1-2: Media Module Spare Parts List
Media Module Components 1 Media module a) Drive tray module* b) Drive cage assembly* c) Media module bezel IMD with cable, panel, LED Power switch assembly with LED 271930-001 122233-001 319945-001
Mass Storage 4 Wide Ultra3 hard drive with tray, 18.2-GB, 1-inch, 10000 rpm Wide Ultra3 hard drive with tray, 36.4-GB, 1-inch, 10000 rpm* Wide Ultra3 hard drive with tray, 18.2-GB, 1-inch, 15000 rpm* U320 Universal hard drive with tray, 36.4-GB, 1-inch, 10000 rpm U320 Universal hard drive with tray, 72.8-GB, 1-inch, 10000 rpm U320 Universal hard drive with tray, 146.8-GB, 1-inch, 10000 rpm U320 Universal hard drive with tray, 18.2-GB, 1-inch, 15000 rpm U320 Universal hard drive with tray, 36.4-GB, 1-inch, 15000 rpm U320 Universal hard drive with tray, 72.8-GB, 1-inch, 15000 rpm LVDS 1-inch hard drive blank 1.44-MB diskette drive drive drive* 152190-001 177986-001 189395-001 289041-001 289042-001 289044-001 289240-001 289241-001 289243-001 313046-001 233409-001 263243-001 339811-001 356326-001

7 CD-ROM 8 DVD

Processor and Memory Module

Chassis Components Removal and Replacement Procedures

I/O Lid

CAUTION: When the server is powered on, the access panel must be installed for proper system cooling. Otherwise, component stress and permanent equipment damage may result.
Open the I/O lid to access the PCI Hot Plug expansion slots, system fans, and configuration switches. To open the I/O lid: 1. Unlock the top latch security screw (1) and then pull the latch forward (2). 2. Slide the I/O lid toward the front of the server (3).
Figure 3-1: Opening the I/O lid
To remove the I/O lid: 1. Remove the processor and memory module. Refer to Chapter 5. 2. Slide the I/O lid out of the front of the server.
Figure 3-2: Removing the I/O lid
NOTE: HP recommends leaving the I/O lid locked during normal use.

Hot-Plug Power Supply

The ProLiant DL760 G2 server ships with two hot-plug power supplies. The system power in the ProLiant DL760 G2 server does not have to be shut off to replace one of the power supplies.
Install the power supply before connecting the power cord to it. Unplug the power cord before removing the power supply from the server. Disconnect power from the server by unplugging all power cords from either the electrical outlet or the server. Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and foam packing.
To estimate the power requirements for a specific server configuration, use the ProLiant DL760 Generation 2 server Power Calculator located on the HP ActiveAnswers Online Solutions website:

activeanswers.hp.com

1. Select System Configurator under Tools. 2. Click Select Product Family and select ProLiant Servers. 3. From the list, select ProLiant DL760 G2 Server. The subsequent Web pages contain information and a link to the ProLiant DL760 Generation 2 server Power Calculator. To replace a hot-plug power supply with the system power on: 1. Remove the power cord from the power supply to replace and release the power cord clamp.
Figure 3-3: Removing the power cord
2. Squeeze upward on the release tab in the middle of the power supply handle (1). 3. Rotate the power supply handle down (2) and slide the power supply out of the chassis (3) as shown in Figure 3-4.
IMPORTANT: Use only the power supply part number for the ProLiant DL760 G2 server. Power supplies from other servers will not fit. IMPORTANT: When you remove the power supply, a spring-loaded trap door closes to block the opening. This door preserves the air path required to cool the internal components of the server.

Figure 5-2: Tightening the security screw
WARNING: The processor and memory module weighs more than 16 kg (35 lbs). HP recommends either removing ALL of the memory cartridges before handling the module or having two people handling the module together. CAUTION: Do not attempt to remove the processor and memory module while power is applied to the system. The module is not hot-pluggable. Immediate system shutdown and data loss will occur.
To remove the processor and memory module: 1. Power down the server. Refer to Pow ering Down the Server in Chapter 2. 2. Push in the sides of the cam levers on the processor and memory module (1) and rotate the top of the levers downward (2), as shown in Figure 5-3. 3. Pull the processor and memory module out of the chassis until the module encounters the module stop latches (3).
Figure 5-3: Opening the processor and memory module
4. Press the module stop latches in (4) and pull the module out of the chassis (5), as shown in Figure 5-4.
Figure 5-4: Removing the processor and memory module
NOTE: The I/O lid labels, processor board cover, and memory cartridge covers also provide instructions about installing processors and DIMMs.
To reassemble the server, slide the module in until the cam levers begin to rotate. Then push the cam levers shut until they snap into place.
Processor Boards and Processors

Identifying

The ProLiant DL760 G2 server is capable of supporting up to eight Intel Xeon processors MP and is shipped with four or eight processors already installed. The ProLiant DL760 G2 server supports two processor boards located in the left side of the processor and memory module.
Figure 5-5: Processor boards Table 5-1: Processor Boards
Item Description Processor board in processor board slot 1 Processor board in processor board slot 2
The ProLiant DL760 G2 server supports four or eight Intel Xeon processors MP. All processors must be the same speed, cache size, and stepping. Processor 1 must always be installed to properly terminate the processor bus.
NOTE: Stepping refers to the processor revision. NOTE: If the server has one processor board (four processors), processor board slot 2 is populated with a processor board air baffle. This baffle must be removed if you are upgrading to eight processors. Refer to the HP ProLiant DL760 Generation 2 Server User Guide for upgrade instructions.

Figure 6-8: Inserting the PCI/PCI-X expansion board
3. Connect the expansion board I/O cable as appropriate. HP has designed a self-latching slot keeper feature to accommodate full-length expansion boards. Be sure that the V-shaped slot keeper tabs on the plastic expansion board guide are positioned over the forward end of the expansion board. Using the slot keepers is especially important when expansion boards are added or when the server is moved.
Figure 6-9: Full-length self-latching slot keeper feature
4. Close the I/O lid and slide the server into the rack. 5. Power up the server. Refer to Pow ering Up the Server in Chapter 2. 6. If necessary, run the ROM-Based Setup Utility, as described in the HP ProLiant DL760 Generation 2 Server User Guide.
NOTE: Refer to the HP QuickSpecs for the ProLiant DL760 G2 servers at www.hp.com for a list of supported I/O expansion boards. NOTE: Each PCI-X bus will automatically configure to run in the most advanced mode (PCI-X or PCI) and the highest frequency supported by all expansion boards installed in the slots on the bus.
PCI Hot Plug I/O Expansion Boards
The ProLiant DL760 G2 server supports PCI Hot Plug. PCI Hot Plug and the operating system of the server work together to allow the following hot-plug actions: Hot-replaceAllows you to replace a failed expansion board with an identical expansion board without powering down the server. Hot-addAllows you to install new PCI/PCI-X expansion boards in previously empty slots without powering down the server under some operating systems. Hot-upgradeAllows you to replace an expansion board with a different expansion board without powering down the server.
PCI Hot Plug is backward-compatible, although system components fit into one of two categories: hot-plug aware or non-hot-plug aware. The following three components are required in the server for complete PCI Hot Plug capability: PCI Hot Plug system hardware (available in this server) Operating system with PCI Hot Plug support (support levels vary) PCI Hot Plug device drivers (available from operating system vendors, the HP SmartStart CD, HP website, and some individual hardware vendors)
WARNING: To reduce the risk of personal injury from hazardous energy or damage to the equipment when working on energized servers:
Remove all watches, rings, and any other loose-fitting jewelry. Avoid the use of conductive tools that could bridge live parts.
IMPORTANT: If any of the three required components are not hot-plug aware, the system is fully functional but is not PCI Hot Plug-capable.
PCI Hot Plug LED Indicators
The PCI Hot Plug amber (1) and green (2) LEDs (shown in the following figure for one slot) provide a visual reference of the status of each slot. The LEDs are viewed from the rear of the server as shown in Figure 6-10 or by opening the I/O lid as shown in Figure 6-11.

Figure 6-10: PCI Hot Plug LEDs from rear of the server
A description and slot status for the PCI Hot Plug LEDs and button as shown in Figure 6-11 are provided in Table 6-2.
Figure 6-11: PCI Hot Plug LEDs in the I/O module
Table 6-2: PCI Hot Plug LEDs and Button
Amber LED Off 1 On OK to Open Slot Condition and Status Slot does not require attention. Slot requires attention. There might be a problem with the slot, the PCI board, or the driver. Check the green LED before opening the slot. Refer to the IML and/or the PCI Hot Plug software application for a description of the problem indicated. Green LED On 2 Blinking OK to Open No No Slot Condition and Status Power is applied to the slot. Power to the slot is being turned off or on. This process might take several minutes. Do not open the slot release lever until the green LED is completely off. You can replace or remove the board in this slot only.
Off PCI Hot Plug Button 3
Each PCI Hot Plug button is used to activate or deactivate its associated PCI Hot Plug slot. Activating or deactivating a PCI Hot Plug slot can also be accomplished through the operating system PCI Hot Plug software application. For more information about the PCI Hot Plug software application, refer to the PCI Hot Plug Operating System Support section.
PCI Hot Plug Operating System Support
Software support is an integral part of PCI Hot Plug. HP, in partnership with Microsoft, Novell, and SCO/Caldera UNIX, has developed PCI Hot Plug software support for each operating system. You can use either the PCI Hot Plug button on the server or the operating systems PCI Hot Plug software to control the PCI Hot Plug slots. You can use the software to indicate that you want to replace an expansion board in the hot-plug slot or configure a board that you have already added to the system. The PCI Hot Plug software also allows you to enable or disable specific system slots. For more information, refer to the HP ProLiant DL760 Generation 2 Server User Guide.
Adding PCI Hot Plug Expansion Boards
The PCI/PCI-X slots of the ProLiant DL760 G2 I/O board are hot-plug-capable and support a variety of industry-standard expansion boards.
NOTE: For a list of supported I/O expansion boards, refer to the HP QuickSpecs for the HP ProLiant DL760 G2 servers:
Refer to Figure 6-10, Figure 6-11, and Table 6-2 for definitions of the PCI Hot Plug LEDs. To add a PCI/PCI-X expansion board into PCI Hot Plug slots 1 through 11: 1. Open the I/O lid. 2. If the PCI Hot Plug green LED is on, power down the slot by pressing the PCI Hot Plug button corresponding to the slot or by using a PCI Hot Plug software application. Wait until the green LED is off.

CAUTION: To avoid system power-down and subsequent data loss, do not open the slot release lever unless the green PCI Hot Plug LED of the slot is off.
NOTE: The PCI Hot Plug Button allows you to press the button again within five seconds of the first press to cancel the action.
3. Press on the top of the appropriate expansion slot release lever (1) and open the lever toward the rear of the expansion slot (2). 4. Remove the expansion slot cover (3).
Figure 6-12: Preparing the hot-plug expansion slot for installation
5. Insert the PCI/PCI-X expansion board into the appropriate expansion slot, pushing firmly until the board is securely seated (1). 6. Close the expansion slot release lever from the rear of the unit to secure the board (2). Be sure that the lever latches into the closed position.
Figure 6-13: Inserting the PCI/PCI-X expansion board
HP has designed a self-latching slot-keeper feature to accommodate full-length expansion boards. Be sure that the V-shaped slot-keeper tabs on the plastic expansion board guide are positioned over the forward end of the expansion board. Using the slot-keepers is especially important when expansion boards are added or when the server is moved.
Figure 6-14: Full-length self-latching slot-keeper feature
7. Properly connect the expansion board I/O cable. 8. Activate power to the slot through the PCI Hot Plug software application or by pressing the PCI Hot Plug Button above the corresponding I/O expansion slot.
Figure 6-15: Activating the PCI Hot Plug Button
9. Check the amber and green LEDs for slot status. The green LED will flash during the power-up transition and will remain lit when the power-up process is complete. For details about PCI Hot Plug LEDs, refer to PCI Hot Plug LED Indicators in this chapter. 10. Close the I/O lid.
Removing or Replacing a PCI Hot Plug Expansion Board
To remove or replace a PCI Hot Plug expansion board: 1. Open the I/O lid of the server. 2. Use the PCI Hot Plug Button or software application to notify the system to turn off power to the slot. Pushing the PCI Hot Plug button notifies the system to shut down operation of this expansion board; lifting the lever actually powers down the expansion slot. The green LED will flash during the power down transition and will turn off when the power down process is complete. For more information about PCI Hot Plug LEDs, refer to PCI Hot Plug LED Indicators earlier in this chapter.
3. Disconnect the cables to the PCI/PCI-X board when the green LED of the slot is off.
4. Press on the top of the appropriate expansion slot release lever (1) and open the lever toward the rear of the expansion slot (2). 5. Unseat the expansion board by pulling up on the plastic tab (3) and lift the board out of the server (4).
Figure 6-16: Removing an I/O expansion board
6. If you are only removing the board, install an expansion slot cover. Close the slot release lever. Be sure that the lever latches into the closed position. 7. If you are replacing the board, install the new I/O expansion board. 8. Close the slot release lever. Be sure that the lever latches into the closed position. 9. Reconnect any I/O cables to the new board. 10. Return power to the slot through the PCI Hot Plug button or software application. The green LED will flash during the power-up transition and will turn on when the power-up is complete. For more information about PCI Hot Plug LEDs, refer to PCI Hot Plug LED Indicators earli er in this chapter. 11. Close the I/O lid.

Tool Array Diagnostics Utility (ADU) What it is ADU is a Windows-based tool designed to run on all HP systems that support HP array controllers. The two main functions of ADU are:
How to run it Use the information provided in the ADU. For a complete list of ADU error messages, refer to the HP Servers Troubleshooting Guide.
To collect all possible information about the array controllers in the system. To generate a list of detected problems.
This tool is available for all HP servers covered by this guide. Drive Array Advanced Diagnostics (DAAD) The predecessor to ADU, DAAD is a DOS-based tool for HP servers with Smart Array Controllers. DAAD collects information about the array controllers in the system and offers a list of detected problems. IML is a log of system events, such as system failures or nonfatal error conditions. View events in the Integrated Management Log from within:
For a list of HP servers still supported by this tool, visit the HP website: www.hp.com
Integrated Management Log (IML)
Insight Manager Survey Utility Operating system-specific IML utilities
The Integrated Management Log requires HP operating systemdependent drivers. Refer to the Support Software CD for instructions on installing the appropriate drivers.

Power-On Self Test

A diagnostic testing sequence run by the server when power is turned on. POST will determine if the server hardware components are properly working. ASR-2 is a feature of HP Systems Health Driver. If a server failure extends beyond a set time, the system reboots and attempts to recover.
For a list of POST error messages, refer to the HP Servers Troubleshooting Guide.
Automatic Server Recovery (ASR-2)

For More Information

For detailed information about each of these diagnostic tools, refer to the HP Servers Troubleshooting Guide. For detailed information on troubleshooting the ProLiant DL760 G2 server, refer to the HP ProLiant DL760 Generation 2 Server User Guide. For detailed information about the RBSU, refer to the ROM-Based Setup Utility User Guide on the Documentation CD.
Connectors, Switches, and LED Indicators

Connectors

This section contains graphics and tables that show the connector locations on the I/O board and processor board of the HP ProLiant DL760 G2 server.

Rear Connectors

Figure 8-1: Rear I/O board connectors
Item Vide 3 Keyboard 4 Mouse 5 Serial Description External Ultra2 tape port connector o connector connector connector port

I/O Board Components

Figure 8-2: I/O board components Table 8-1: I/O Board Components
Item 1, 2 3, 4 5, 6 7, 10, 13 Description Bus 19 (slots 1 and 2) 64-bit/100-MHz/3-V PCI-X Hot Plug Bus 15 (slots 3 and 4) 64-bit/100-MHz/3-V PCI-X Hot Plug Bus 11 (slots 5 and 6) 64-bit/100-MHz/3-V PCI-X Hot Plug Bus 7 (slots 7 and 8) 64-bit/100-MHz/3-V PCI-X Hot Plug Bus 0 (slot 9) 64-bit/100-MHz/3-V PCI Hot Plug Bus 3 (slots 10 and 11) 64-bit/100-MHz/3-V PCI-X Hot Plug PCI Hot Plug board cable connector Non-Maskable Interrupt (NMI) switch Item Boot Description Hot-plug Fan 1 assembly connector block I/O board configuration switches (SW1) Hot-plug Fan 2 assembly connector battery

System Power LED Indicator
Figure 8-5 shows the location of the system power LED (1).
Figure 8-5: System Power LED
Auxiliary Power LED Indicator
Figure 8-6 shows the location of the auxiliary power LED (1) on the I/O board.
Figure 8-6: Auxiliary power LED
System Interconnect LED Indicators
To prevent damage to critical system components, the ProLiant DL760 G2 server will not power up if it detects that certain components are not installed or are installed incorrectly. The system interconnect LEDs provided with ProLiant DL760 G2 servers provide a closed-loop checking mechanism for verifying proper component mating and interconnections between critical server components. LEDs inside the sliding top cover provide visual assistance in isolating components to check if the server will not power up due to a component or module that is not fully installed. If a status indicator light is on, reseat the component represented by the indicator. Refer to the hood labels for component location.
IMPORTANT: To check system interconnect status LEDs, place the server in Standby with the power supplies plugged in.
Figure 8-7: System interconnect LEDs
Item 9 Description I/O module interconnect Processor and memory module interconnect Processor board 1 interconnect Processor board 2 interconnect Memory riser board interconnect Media module interconnect SCSI backplane 1 interconnect SCSI backplane 2 interconnect Interconnect check light
System Attention LED Indicators
Figure 8-8: System attention LED indicators
Item Description Hot-plug Fan 1 attention LED Hot-plug Fan 2 attention LED Processor board 1 attention LED Processor board 2 attention LED
Hot-Plug SCSI Hard Drive LED Indicators
The hot-plug SCSI hard drive LEDs, located on each physical drive, are visible on the front of the server or external storage unit. They provide: (1) Activity, (2) Power/Online, and (3) Fault status for each corresponding drive when configured as a part of an array and attached to a powered-on controller. Their behavior can vary, depending on the status of other drives in the array.
Figure 8-9: Hot-plug SCSI hard drive LEDs
Figure 8-10: SCSI hard drive LEDs

Power Supply LED Indicators
Each power supply has status and AC power LEDs. Refer to Figure 8-11 and Table 8-3 for a detailed description of both indicators.
Figure 8-11: Power supply LEDs Table 8-3: Power Supply LEDs
Item Condition Green Normal Green/Amber alternating 1 Status Green blinking Amber Amber blinking Off 2 AC Power Green Off Meaning operation. Power supply failed to restart after a prolonged fault. Power supply will restart within 20 seconds. Fault detected in this power supply. Power supply failed self-test. System is in standby mode, or interlocks are disabled. AC power is connected to this power supply. No AC power is connected to this power supply.
Hot-Plug Fan LED Indicators
The ProLiant DL760 G2 server ships with two hot-plug fans. Fan 1 is closest to the rear of the server. Each fan has LEDs that indicate the following fan statuses: Green LED (1)Fan is installed and working properly. Amber LED (2)The fan needs attention or is not ins talled.
Figure 8-12: Hot-plug fan LEDs
CAUTION: Never remove both hot-plug fans while the server is powered up. Overheating and damage to hardware could result. If the appropriate HP software drivers are installed, the operating system software will initiate a power shutdown if overheated. NOTE: The hot-plug fan LEDs are not part of the fan housing. Figure 8-12 shows the LEDs as if the fan were installed in the server.
The PCI Hot Plug amber (1) and green (2) LEDs (shown in the following figure for one slot) provide a visual reference of each slots status. The LEDs are viewed from the rear of the server, as shown in Figure 8-13, or by opening the I/O lid, as shown in Figure 8-14.
Figure 8-13: PCI Hot Plug LEDs from rear of the server
Figure 8-14: PCI Hot Plug LEDs in the I/O module
A description and slot status for the PCI Hot Plug LEDs and button, as shown in Figure 8-14, are provided in Table 8-4.
Table 8-4: PCI Hot Plug LEDs and Button
Amber LED Off 1 On OK to Open Slot Condition and Status Slot does not require attention. Slot requires attention. There could be a problem with the slot, the PCI board, or the driver. Check the green LED before opening the slot. Refer to the IML and/or the PCI Hot Plug software application for a description of the problem indicated. Green LED On 2 Blinking OK to Open No No Slot Condition and Status Power is applied to the slot. Power to the slot is being turned off or on. This process could take several minutes. Do not open the slot release lever until the green LED is completely off. You can replace or remove the board in this slot only.
Memory Cartridge LED Indicators
The ProLiant DL760 G2 server has LEDs for each of the memory cartridges. These LEDs are used to determine the status of memory installed in the server.

Figure 8-15: Memory cartridge LEDs Table 8-5: Memory Cartridge LEDs
Item 7 LED Indicator Cartridge 1 DIMM status LED Cartridge 2 DIMM status LED Cartridge 3 DIMM status LED Cartridge 4 DIMM status LED Cartridge 5 DIMM status LED Cartridge power LED Cartridge attention LED LED Icon 12345678
Note: These LEDs are backlit through icon lenses. An icon only appears when the LED is illuminated.
Physical, Operating, and Performance Specifications
This section provides physical, operating, and performance specifications for the following components of the HP ProLiant DL760 G2 server: Server Power supply Dual inline memory module (DIMM) 1.44-MB diskette drive 24X Max (or higher) IDE CD-ROM drive (low profile) Hot-pluggable Wide Ultra3 and U320 SCSI hard drives Smart Array 5i Controller NC7770 PCI-X Gigabit Server Adapter

Server Specifications

Table 9-1: HP ProLiant DL760 G2 Server Specifications
Dimensions Height Depth Width Weight (no drives and two power supplies) Input Requirements (per power supply) Rated Input Voltage Rated Input Frequency Rated Input Current Power Supply Output Power (per power supply) Rated Steady-State Power Maximum Peak Power Temperature Range Operating Shipping Relative Humidity (noncondensing) Operating Nonoperating Maximum Wet Bulb Temperature * Altitude derating: C/1000 ft to 10,000 feet.
30.5 cm/12.0 in 68.5 cm/27.0 in 44.5 cm/17.5 in 52.3 kg /140 lb Low Range/High Range 100 to 120 V/200 to 240 V 50 to 60 Hz/50 to 60 Hz 8 A/10 A Low Range/High Range 500 W/1150 W 549 W/1150 W
10 to 35 C (50 to 95 F)* -30 to 60 C (-22 to 122 F)
10% to 90% 5% to 90% 38.7 C (101.7 F)
Power Supply Specifications
Table 9-2: Power Supply Specifications
General specifications Full output rating To 40 C and 1,525 m (to 104 F and 5,000 ft) To 32 C and 3,050 m (to 90 F and 10,000 ft) (derate linearly) Minimum load 1.0 A on + 5 V output 1.0 A on + 12 V output 0.5 A on + 3.3 V output
Ambient temperature range Operating Storage Input specifications Nominal line voltage Range input line Frequency range Power factor Input power Input current Inrush current Holdup time Dielectric voltage withstand Input to output Input to ground Input transient susceptibility Common and differential mode (superimposed on AC line) Differential mode 2500 V, 10 s pulse 20% step change in AC input voltage 3000 VAC per minute/3000 VAC per minute 1500 VAC per minute/1500 VAC per minute 10 to 40 C (50 to 104 F) -40 to 65 C (-40 to 149 F) Low Range/High Range 100 to 120 VAC/200 to 240 VAC 90 to 132 VAC/180 to 265 VAC 47 to 63 Hz/47 to 63 Hz 0.95/0.W @ 110 V/1150 W @ 220 V 8 A at 100 VAC/10 A at 200 VAC <70 A at 132 VAC (cold start)/< 35 A at 265 VAC (cold start) 20 ms from zero crossing at 120 VAC/20 ms from zero crossing at 120 VAC
Dual Inline Memory Module (DIMM) Specifications
Table 9-3: DIMM Specifications
Size Speed Upgrade requirement Type 256 MB, 512 MB, or 1 GB 60 ns or faster Bank of two DIMMs; must be same type, size, speed, and manufacturer Buffered ECC protected DIMMs; SDRAM

1.44-MB Diskette Drive Specifications
Table 9-4: Diskette Drive Specifications
Size 3.5 LED indicators (front panel) Read/write capacity per diskette (high/low density) Drives supported Drive height Drive rotation Transfer rate bits per sec (high/low) Bytes per sector Sectors per track (high/low) Tracks per side (high/low) Access times Track-to-track (high/low) Average (high/low) Settling time Latency average (high/low) Cylinders (high/low) Read/write heads 6 ms/3 ms 174 ms/94 ms 15 ms 100 ms/83 ms 80/in Green 1.44 MB/720 KB 1 1/rpm 500/250 K 512 18/9 80/80
DVD-ROM Drive Specifications
Table 9-5: DVD-ROM Drive Specifications
Dimensions Height Width Depth Weight Operating conditions Temperature Humidity Applicable disk 5 to 45 C (41 to 113 F) 10% to 80% CD-ROM (mode 1 and 2), CD-DA, CD-XA (mode 2, form 1 and 2), photo CD (single-session and multi-session), mixed mode (audio and data combined) 550 MB (mode 1, 12 cm) 640 MB (mode 2, 12 cm) 2048, 1024 bytes (mode 1) 2340, 2336, 1024 bytes (mode 2) 2352 bytes (CD-DA) 2328 bytes (CD-XA) 12 cm, 8 cm (4.7 in, 3.15 in) 4200 rpm maximum 15 mm (0.6 in) 1.6 m 4.29 cm (1.69 in) 15.0 cm (5.75 in) 20.8 cm (8.19 in) 1200 g (2.66 lb)

Capacity Block size

Diameter Rotational speed Center hole thickness Track pitch Data transfer rate Sustained Variable Data transfer method Access times (typical) Full stroke Random Cache/buffer 128 Startup time (typical) Stop time Audio output level Line out Headphone
150 KB/s (single) 1200-3600 KB/s (8X to 24X) 32-bit bus master PCI
200 ms 100 ms KB >7s >4s
0.7 VRMS at 47 Ohms 0.6 VRMS at 32 Ohms (maximum width)
Table 9-5: DVD-ROM Drive Specifications continued
Laser parameters Type Wave length Divergence angle Output power Interface IDE Semiconductor laser GaA1As 780 +/- 25 nm 53.5 +/- 1.5 0.14 mW (ATAPI)
24X Max IDE CD-ROM Drive Specifications
Table 9-6: 24X Max IDE CD-ROM Drive Specifications
Dimensions Height Width Depth Weight Operating conditions Temperature Humidity Applicable disk 5 to 45 C (41 to 113 F) 10% to 80% CD-ROM (mode 1 and 2), CD-DA, CD-XA (mode 2, form 1 and 2), photo CD (single-session and multi-session), mixed mode (audio and data combined) 550 MB (mode 1, 12 cm) 640 MB (mode 2, 12 cm) 2048, 1024 bytes (mode 1) 2340, 2336, 1024 bytes (mode 2) 2352 bytes (CD-DA) 2328 bytes (CD-XA) 12 cm, 8 cm (4.7 in., 3.15 in.) 4200 rpm maximum 15 mm (0.6 in.) 1.6 m 4.29 cm (1.69 in) 15.0 cm (5.75 in) 20.8 cm (8.19 in) 1200 g (2.66 lb)

NC7770 PCI-X Gigabit Server Adapter Specifications
Table 9-10: NC7770 PCI-X Gigabit Server Adapter Specifications
Network interface Compatibility Data path Bus architecture Network transfer rate 10Base-T (half-duplex), 10Base-2 10Base-T (full-duplex) 100Base-TX (half-duplex) 100Base-TX (full-duplex) 1000Base-TX (half-duplex) 1000Base-TX (full-duplex) Connector RJ-45 I/O address and interrupt Cable support Operating system driver support Automatic configuration Category 5 or higher UTP; up to 100 m (328 ft) Microsoft Windows Server 2003 Microsoft Windows 2000 Microsoft Windows NT 4.0 Caldera OpenUnix 8 Linux 10 Mbps 20 Mbps 100 Mbps 200 Mbps 1000 Mbps 2000 Mbps 10Base-T/100Base-TX IEEE 802.3i, 802.3u, 802.3x, 802.3ab, 802.3ad compliant PCI-X 1.0, PCI 2.2, ACPI v1.1a 64/133 MHz, compatible with 64/100, 64/66, 66/33, and 32/33 PCI-X bus mastering, compatible with existing PCI bus architecture
NC7170 Dual Port PCI-X Gigabit Server Adapter Specifications
Table 9-11: NC7170 Dual Port PCI-X Gigabit Server Adapter Specifications
Network interface Compatibility 10/100/1000 base-T IEEE 802.3, 802.3u, 802.3x, 802.3ab, 802.3ad (static mode configuration only), 802.1p, 802.1Q, PCI-X 1.0, PCI 2.2, ACPI v1.1a 64-bit/133MHz, compatible with 64/100, 64/44, 64/33, 32/33 PCI-X bus mastering, compatible with existing PCI bus architecture Two RJ-45 Category 5 or higher UTP; up to 100 m (328 ft) Microsoft Windows Server 2003 Microsoft Windows 2000 Novell NetWare 4.x, 5.x, 6.x Server Linux - selected Red Hat and SuSE distributions SCO OpenUnix 8 and OpenServer 5 MS-DOS Client for unattended installation
Data path Bus architecture Bus Connector Cable support Operating system driver support
CD-ROM drives location 4-1 removing 4-10 specifications 9-7 chassis, part number 1-3 component-level repairs vii connectors host board 8-3 I/O board 8-2 processor boards 8-3 rear panel 8-1 controllers Fast Ethernet 9-12, 9-13 Smart Array 9-11 country kit 1-11
11-slot hot-plug basket 6-22
ADU (Array Diagnostics Utility) location 2-8 overview 7-4 Advanced Data Guarding 4-8 Array Diagnostics Utility (ADU) location 2-8 overview 7-4 array enabler board part number 1-9 removing 6-22 auxiliary power LED indicator 8-6

DAAD (Drive Array Advanced Diagnostics) location 2-8 overview 7-4 diagnostic tools location 2-8 overview 7-2 DIMMs (Dual Inline Memory Modules), part numbers 1-7 diskette drives integrated 4-10 location 4-1 specifications 9-4 Drive Array Advanced Diagnostics (DAAD) location 2-8 overview 7-4 Dual Inline Memory Modules (DIMMs), part numbers 1-7 DVD-ROM drive specifications 9-5
battery part number 1-11 removing/replacing 6-24 bezels, media module removing/replacing 4-4 blanking panels, hard drives 1-5, 4-7 boards array enabler 6-22 host board connectors 8-3 I/O connectors 8-2 I/O switches 8-4 memory 1-7 PCI Hot Plug 1-9 processor, part numbers 1-7 brackets, cable management arm 6-1
cable management arm, removing 6-1 cables CD-ROM drive signal 4-12 diskette drive control and data 4-12 diskette drive power 4-12 IMD 4-12 power switch/LED/ambient air temperature sensor 4-12

Index-1

electrostatic discharge (ESD) 2-1 Enterprise Diagnostics LX 32 Utility 7-2 ESD (electrostatic discharge) 2-1 Ethernet controllers 9-12, 9-13 Ethernet loopback RJ-45 1-11
F2 key 4-8 fan cage assemblies I/O module 1-9 removing/replacing 6-20 fans LED indicators 8-12 replacing 6-18 Fast Ethernet Controller 9-12, 9-13 fault tolerance 4-9
I/O lid opening 3-1 part number 1-3 I/O module accessing 2-7 exploded view 1-8 part numbers 1-3 removing/replacing 6-4 illustrated parts catalog 1-1 IMD (Integrated Management Display) 4-5 IML (Integrated Management Log) 7-4 Insight Manager 7-2 installing I/O expansion boards 6-10 PCI Hot Plug expansion boards 6-14 power supplies 3-2 processors 5-5 SDRAM DIMMs 5-15 internal battery 6-24
grounding viii grounding plug vii grounding procedures 2-1, 2-2
LED indicators auxiliary power 8-6 fans 6-18, 8-12 Hot Plug RAID Memory 8-15 overview 8-5 PCI Hot Plug 6-12, 8-13 power supply 8-11 SCSI hard drives 8-9 system attention 8-8 system interconnect status 8-7 system power 8-6 LVDS hard drive blank 1-5
hard drives blanks 4-7 LED indicators 8-9 part numbers 1-5 removing/replacing 4-9 help resources viii hot plug power supplies 3-2 Hot Plug RAID Memory cartridge LED indicators 8-15 hot surfaces 5-6 hot-plug components 11-slot hot-plug basket 6-22 fans 6-18, 8-12 hard drives 8-9 power supplies 1-3 HP authorized reseller viii
media module accessing 2-7 contents 4-1 exploded view 1-4 part numbers 1-3 removing/replacing 4-2 memory cartridge LED indicators 8-15 memory riser board 5-17 memory, part numbers 1-7 midplane assembly, removing/replacing 3-5 modules access methods 2-7 media 4-1 processor and memory 5-3
I/O components board connector locations 8-2 expansion slots 6-7 switches 8-4 I/O expansion boards installing 6-10 locating I/O expansion slots 6-6

Index-2

NC7170 Fast Ethernet Controller 9-13 NC7770 Fast Ethernet Controller 9-12
operating systems, PCI Hot Plug support 6-13

QuickSpecs

Overview

HP ProLiant DL760 Generation 2 (G2)
1. Processor/Memory Module 2. Hot Plug RAID Memory Cartridge 3. Four or Eight Intel Xeon Processors MP with fault tolerant processor power modules 4. DIMM Status LED 5. Integrated Management Display 6. Integrated 1.44-MB Diskette Drive 7. Media Module 8. Integrated Slimline CD/DVD-ROM Drive, (8X speed for DVD and 24X speed for CD)
9. Four Ultra320 SCSI Hot Plug Drive Bays (running U3 speeds) 10. Attention LED Indicators 11. System Interconnect Status Indicator 12. Integrated Lift Handles 13. Redundant Hot Plug Fans 14. Two Redundant Hot Plug Power Supplies 15. I/O Modules 16. Eleven 64-bit PCI-X and PCI I/O expansion slots, all Hot Plug (10 x 100 MHz PCI-X and 1 x 33 MHz PCI)

What's New

Intel Xeon Processor MP 3.0 GHz/4MB, 2.7 GHz/2MB, or 2.2 GHz/2MB, Processors (eight processor capability) Integrated HP NC7170 Dual-Port PCI-X 1000T Gigabit Server Adapter in a slot Integrated Slimline CD/DVD-ROM Drive now ships standard in new models

DA - 11568

Worldwide Version 49 March 27, 2006

Page 1

At A Glance
Intel Xeon Processor MP 3.0 GHz/4MB, 2.7 GHz/2MB, 2.2 GHz/2MB Processors (eight processor capability) Hot Plug RAID Memory using XOR & ECC-protected memory and user-friendly diagnostics The ultimate high-density data center server delivering breakthrough 8-way scalable performance for 7 x 24 multi-server rack environments Tool less chassis for enhanced serviceability 133 MHz SDRAM DIMM memory that is expandable to 64 GB addressable memory (+16GB for full redundancy) Integrated Smart Array 5i Controller (Ultra3 support) (supports RAID 0, 1, 1+0, and 5 across internal hard disk drives) (One Internal Channel for RAID Capability for internal drives and one External Channel for tape support only) (10) 64-bit/100MHz capable PCI-X slots & (1) 64-bit/33-MHz PCI slot Full RILOE II support Integrated NC7770 PCI-X Gigabit Server Adapter or Integrated HP NC7170 Dual-Port PCI-X 1000T Gigabit Server Adapter standard depending on the model Internal Hot Plug Drive Storage of 1.20TB (4 x 300GB Ultra320 HDD running U3) or one DAT hot plug tape drive and two hot plug hard drives Robust set of hot plug and redundant features including Hot Plug RAID Memory, PCI/PCI-X Hot Plug, hot plug drive bays, redundant hot plug fans and power supplies and support for redundant NICs, ASR-2, Remote-Flash Redundant ROM Protected by HP Services and a worldwide network of resellers and service providers. Three-year Next Business Day, on-site limited global warranty. Certain restrictions and exclusions apply. Pre-Failure Notification on processors, memory, and SCSI hard drives.

Page 2

Standard Features
Processor One of the following depending on Model (4) Intel Xeon Processor MP 3.0 GHz/4MB (4) Intel Xeon Processor MP 2.7 GHz/2MB (4) Intel Xeon Processor MP 2.2 GHz/2MB
Cache Memory One of the following depending on Model
4-MB Integrated Level 3 cache (per processor) NOTE: Available with 3.0 GHz models. 2-MB integrated level 3 cache (per processor) NOTE: Available with 2.7 GHz or 2.2 GHz models.

Upgradeability

Upgradeable to eight processors

Chipset

HP developed F8 chipset

Memory Protection

Advanced ECC Hot Plug RAID Memory

Memory

Type 133MHz ECC SDRAM DIMMs Standard 2 GB NOTE: Available with 2.2 GHz model. Standard 4 GB NOTE: Available with 3.0 GHz or 2.7 GHz models. Maximum 64 GB (80 GB total) NOTE: All models come standard with all five memory cartridges populated and Hot Plug RAID Memory enabled. NOTE: In standard Hot Plug RAID Memory mode, addressable memory refers to the portion of memory that is addressable by the OS. Total memory consists of addressable memory plus the redundant memory (stored in the dedicated parity memory cartridge.)

Network Controller

Integrated HP NC7170 Dual-Port PCI-X 1000T Gigabit Server Adapter in a slot NOTE: Available with 3.0 GHz, 2.7 GHz, and 2.2 GHz models.

Page 7

System Fans
Two Hot-Plug redundant fans ship standard. Two maximum supported.

Required Cabling

For required cabling information, refer to the Web site at: http://hp.com/products/servers/ProLiantDL760.

OS Support

Microsoft Windows 2000 Microsoft Windows 2000 Advanced Server Microsoft Windows Server 2003 (Standard, and Enterprise) SCO UnixWare LINUX (Red Hat, SuSE) VMware Virtualization Software NOTE: For a more complete and up-to-date listing of supported OS's and versions, please visit our OS Support Matrix at: http://www.hp.com/go/supportos. NOTE: For an up-to-date listing of the latest drivers available for the HP ProLiant DL760 G2, please see: http://h18023.www1.hp.com/support/files/server/us/index.html. NOTE: For a more complete and up-to-date information on Linux support, please visit HP Linux Web site at http://h18000.www1.hp.com/products/servers/linux/hpLinuxcert.html. NOTE: For more complete and up-to-date information on how to buy server operating systems from HP please visit the OS product site at: http://h18004.www1.hp.com/products/servers/software/OEM.html NOTE: For more information on HP's Certified and Supported ProLiant Servers, please visit the VMware Server Support Matrix at: http://h18004.www1.hp.com/products/servers/software/vmware/hpvmwarecert.html.
Rack Airflow Requirements
Rack 10000 series Cabinets The increasing power of new high-performance processor technology requires increased cooling efficiency for rack-mounted servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to be fully loaded with servers using the latest processors. CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to prevent damage to the equipment: Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent open area for ventilation). Side: The clearance between the installed rack component and the side panels of the rack must be a minimum of 2.75 inches (7 cm). CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage. NOTE: For additional information, refer to the Setup and Installation Guide or the Documentation CD provided with the server, or to the server documentation located in the Support section at the following URL: http://h18000.www1.hp.com/products/servers/ProLiantdl760/index.html. NOTE: Allow a minimum of 48 in (121.92 cm) clearance beyond the front of your rack to permit server installation and removal. This applies to both individual rack installations as well as when aligning rack rows so that the front doors are facing each other.

Country Code Key xx=B2 xx=29 xx=AA
Rack Code Key Worldwide Japan PRC

Page 11

Options
ProLiant Essentials Value Pack Software
ProLiant Essentials Intelligent Networking Pack ProLiant Essentials Intelligent Networking Pack - Windows Edition, Single Server License NOTE: For use with a single server. Contains one license with a unique license activation key and documentation. NOTE: For additional ProLiant Intelligent Networking Pack - Windows License Kits please see the QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/12062_div/12062_div.HTML ProLiant Essentials Intelligent Networking Pack - Linux Edition, Single Server License NOTE: For additional ProLiant Intelligent Networking Pack - Linux License Kits please see the QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/12327_div/12327_div.HTML ProLiant Essentials Performance Management Pack ProLiant Essentials Performance Management Pack, Single-Server License NOTE: For use with a single server. Contains one license with a unique license activation key, HP Management CD and documentation. NOTE: The most recent version of the software can always be downloaded at http://www.hp.com/products/pmp. NOTE: For additional ProLiant Performance Management Pack License Kits please see the QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11925_div/11925_div.HTML ProLiant Essentials Rapid Deployment Pack Windows Edition and Linux Edition Release Rapid Deployment Pack, Single-Server License NOTE: This license allows 1 server to be deployed and managed via RDP. Rapid Deployment Pack, Single-Server License (Japan) NOTE: This license allows 1 server to be deployed and managed via RDP. NOTE: For additional ProLiant Essentials Rapid Deployment Pack License Kits please see the QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11053_div/11053_div.HTML http://h18000.www1.hp.com/products/quickspecs/11713_div/11713_div.HTML ProLiant Essentials Workload Management Pack ProLiant Essentials Workload Management Pack, Single Server License NOTE: For additional ProLiant Workload Management Pack License Kits please see the QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11452_div/11452_div.HTML ProLiant Essentials Virtualization Management Software ProLiant Essentials Virtual Machine Management Pack, Single-Server License NOTE: For use with a single server. Contains one license with a unique license activation key and documentation. ProLiant Essentials Server Migration Pack, Single-Migration License NOTE: Contains one license, enabling 1 server migration, with a unique license activation key and documentation. NOTE: This license allows 1 server to be migrated from a physical server to a virtual machine. Or this license can be used to migrate a virtual machine from one virtualization layer i.e. VMware GSX to a different virtualization layer such as VMware ESX or Microsoft Virtual Server 2005.

273915-B21 273914-B21 372538-B21 291966-B21 291967-B21 351580-B21

254786-B21

268351-B21

273911-B21

Page 15

Communications

HP NC310F PCI-X 1000SX Gigabit Server Adapter HP NC7170 PCI-X Dual Port 1000T Gigabit Server Adapter HP NC7771 PCI-X 1000T Gigabit Server Adapter HP NC570C PCI-X Dual-port 4x Fabric Adapter HP 24-Port 4x Fabric Copper Switch HP 1m 4x Fabric Copper Cable HP 3m 4x Fabric Copper Cable HP 5m 4x Fabric Copper Cable
368169-B21 313881-B21 290563-B21 376158-B21 376227-B21 376232-B21 376232-B22 376232-B23

Redundant Options

1150/500-Watt Hot Plug N 1 redundant power supply (North America) 1150/500-Watt Hot Plug N 1 redundant power supply (Intl) 1150/500-Watt Hot Plug N 1 redundant power supply (Japan) NOTE: A maximum of two power supplies are supported by the HP ProLiant DL760 G2 (shipped standard with each server).
401231-001 401231-B31 401231-291

Management Options

Remote Insight Lights-Out Edition II (NA, LA) Remote Insight Lights-Out Edition II (EMEA) Remote Insight Lights-Out Edition II (ROW)
227251-001 227251-021 227251-371

Tape Drives

NOTE: For the complete listing of Tape Drive offerings for this server, please visit: http://www.hp.com/products1/storage/compatibility/tapebackup/ISS/index.html For recommended tape drive offerings for this ProLiant server see the following: Hot Plug Tape Drives HP StorageWorks DAT 72 SCSI Hot-plug Tape Drive (Carbon) USB Tape Drives HP StorageWorks DAT 72 USB External Tape Drive (Carbonite) External and Rack-Mount Ultrium Tape Drives HP StorageWorks Ultrium 232 Internal Tape Drive (Carbonite) NOTE: No internal tape drives fit inside this HP ProLiant server (except hot plug tape). The internal drive shown here is for the 1U and 3U Rack-mount Kit. HP StorageWorks Ultrium 232 External Tape Drive (Carbonite) HP StorageWorks Ultrium 448 External Tape Drive (Carbonite) HP StorageWorks Ultrium 960 External Tape Drive (Carbonite) HP StorageWorks 3U Rack-mount kit with one Ultrium 960 (Carbonite) NOTE: Please see the HP StorageWorks Ultrium Tape Drive QuickSpecs for additional options such as controllers, media, and other related items: http://h18006.www1.hp.com/products/quickspecs/11739_div/11739_div.html (Worldwide) For an up-to-date listing of the latest O/S and software support details for HP Ultrium tape drives, please visit: http://www.hp.com/go/connect. Rack-Mount Tape Drive Enclosures

Q1529A DW027A DW064A

DW065B DW017B Q1539B Q1595A

Page 16

HP StorageWorks 1U Rack-Mount Kit NOTE: NOTE The 1U Rack-mount Kit can support up to (2) half-height tape drives and compatible with multiple Single-Ended and LVD SCSI tape drives including the DAT 24, DAT 40, DAT 72, DLT VS80, DLT VS160, Ultrium 215, Ultrium 232 and Ultrium 448 tape drives. HP StorageWorks 1U USB Rack-Mount Kit 1U USB Cable Option Kit NOTE: Converts a 1U SCSI rack-mount kit to a USB interface to support the USB tape drives. HP StorageWorks 3U Rack-Mount Kit NOTE: The 3U Rack-mount Kit can support up to (2) full-height or (4) half-height tape drives and compatible with multiple Single-Ended and LVD SCSI tape drives including DAT 24, DAT 40, DAT 72, DLT VS80, DLT VS160, SDLT 320, SDLT 600, Ultrium 215, Ultrium 230, Ultrium 232, Ultrium 460, Ultrium 448 and Ultrium 960 tape drives. NOTE: Please see the Rack-Mount Tape Drive Kits QuickSpecs for additional information regarding these kits: http://h18000.www1.hp.com/products/quickspecs/10854_div/10854_div.HTML (Worldwide)

A7445B

A8007A 396114-B21

274338-B22

Tape Autoloaders
DAT Autoloader HP StorageWorks DAT 72x6 Autoloader (External) NOTE: Please see the DAT Tape Autoloader QuickSpecs for additional options such as host bus adapters, controllers and media: http://h18000.www1.hp.com/products/quickspecs/11985_div/11985_div.HTML (Worldwide) HP StorageWorks 1/8 Tape Autoloader HP StorageWorks 1/8 Ultrium 960 Tape Autoloader HP StorageWorks 1/8 Ultrium 448 Tape Autoloader HP StorageWorks 1/8 Ultrium 232 Tape Autoloader 1/8 Tape Autoloader Rackmount Kit NOTE: Required to install the unit in a standard 19-inch rack; includes rails and rackmount instructions. NOTE: Please reference the 1/8 Tape Autoloader QuickSpecs at http://www.hp.com/go/automation for additional information needed to create a complete solution; reference current compatibility information at http://www.hp.com/go/ebs.

Q1567A

AF204A AF203A AF202A C9268R

Page 17

Tape Libraries
HP StorageWorks MSL2024 Tape Library HP StorageWorks MSLUltrium 960 Drive Library HP StorageWorks MSLUltrium 448 Drive Library HP StorageWorks MSLUltrium 448 Drive Library HP StorageWorks MSL4048 Tape Library HP StorageWorks MSLUltrium 448 Drive Library HP StorageWorks MSLUltrium 448 Drive Library HP StorageWorks MSLUltrium 960 Drive Library HP StorageWorks MSLUltrium 960 Drive Library HP StorageWorks MSL6000 Tape Library Ultrium 960 technology HP StorageWorks MSLUltrium 960 Dr LVDS Library HP StorageWorks MSLUltrium 960 Dr FC Library HP StorageWorks MSLUltrium 960 Dr LVDS Library HP StorageWorks MSLUltrium 960 Dr FC Library Ultrium 460 technology HP StorageWorks MSLUltrium 460 Dr LVDS Library HP StorageWorks MSLUltrium 460 Dr FC Library HP StorageWorks MSLUltrium 460 Dr LVDS Library HP StorageWorks MSLUltrium 460 Dr FC Library NOTE: Please reference the MSL2024, MSL4048 and MSL6000 Tape Library QuickSpecs at http://www.hp.com/go/automation for additional information needed to create a complete solution; reference current compatibility information at http://www.hp.com/go/ebs. HP StorageWorks 9.1 GB Optical Jukeboxes 600mx, 4 drive, 64 slot jukebox 1200mx, 4 drive, up to 128 slots 2200mx, 6 drive, up to 238 slots NOTE: Please see the HP StorageWorks Magneto-Optical Products data sheet for a complete listing of available jukeboxes at: http://www.hp.com/products1/storage/products/archivalprod/brochures/ MO_family_pb.pdf NOTE: Please reference the Magneto-Optical Jukebox data sheets at http://www.hp.com/go/optical for additional information needed to create a complete solution. 1900ux, 4 drive, 64 slot jukebox 3800ux, 4 drive, 128 slot jukebox 7100ux, 6 drive, 238 slot jukebox NOTE: Please see the HP StorageWorks Ultra Density Optical Jukeboxes QuickSpecs for a complete listing of available jukeboxes at: http://h18006.www1.hp.com/products/quickspecs/11944_div/11944_div.html NOTE: Please reference the Ultra Density Optical Jukebox QuickSpecs at http://www.hp.com/go/optical for additional information needed to create a complete solution.

AG115A AG116A AG117A AG320A AG321A AG322A AG323A
AD606A AD608A AD607A AD609A AD598A AD600A AD599A AD601A
Magneto-Optical Jukeboxes

C1160M C1104M C1107M

Ultra Density Optical Jukeboxes

AA966A AA969A AA971A

Page 18
HP Data Protector Express HP DP Express Backup Server Upgrade for ProLiant Software Software HP DP Express Package for Microsoft Small Business Server NOTE: Please see the HP Data Protector Express QuickSpecs for additional information regarding the purchase of HP Data Protector Express software: http://h18000.www1.hp.com/products/quickspecs/12337_div/12337_div.html (Worldwide)

BB117AP BB118AA

HP StorageWorks Modular Smart Array 20
HP StorageWorks Modular Smart Array 20 NOTE: Rack-mountable 12 (SATA) drive enclosure with U320 Host connectivity, redundant power supplies. HP StorageWorks Modular Smart Array 20 Starter Kit NOTE: Rack-mountable 12 (SATA) drive enclosure with U320 Host connectivity, redundant power supplies. Includes Smart Array 6402/128 Controller. NOTE: The Modular Smart Array Enclosure 20 Family supports the SATA 1.5Gb/s 3.5" Hot Plug Hard Drives.

335921-B21

366172-B21
HP StorageWorks Modular Smart Array 30
HP StorageWorks Modular Smart Array 30 SB NOTE: Rack-mountable 14 drive enclosure with single bus, redundant power supplies. HP StorageWorks Modular Smart Array 30 DB NOTE: Rack-mountable 14 drive enclosure with dual bus, redundant power supplies. NOTE: The Modular Smart Array Enclosure 30 Family supports the Wide Ultra3, Ultra320 Hot Plug Hard Drives.

302969-B21

302970-B21
HP StorageWorks Modular Smart Array 500 Generation 2 HP StorageWorks Modular Smart Array 500 NOTE: Please see the Modular Smart Array 500 Generation 2 QuickSpecs for additional information including configuration steps and additional options needed for a complete solution at: http://h18000.www1.hp.com/products/quickspecs/11956_div/11956_div.HTML (Worldwide)

335880-B21

HP StorageWorks Modular Smart Array 1000
HP StorageWorks Modular Smart Array 1000 NOTE: Please see the Modular Smart Array 1000 QuickSpecs for additional options and configuration information at http://h18000.www1.hp.com/products/quickspecs/11033_div/11033_div.HTML (Worldwide)

201723-B22

HP StorageWorks Modular Smart Array 1500 cs
Modular Smart Array 1500 Controller Shelf NOTE: Please see the StorageWorks Modular SAN Array 1500 cs QuickSpecs for additional options and configuration information at: http://www.hp.com/go/MSA1500cs

AA986A

Page 19

Cluster Options

ProLiant Cluster Starter Kit NOTE: For additional information regarding the ProLiant Cluster Starter Kit please see the following QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11935_div/11935_div.html (Worldwide) HP HA/F200 for Entry SAN Cluster HP HA/F200 for Entry SAN Cluster (Japan) NOTE: For additional information regarding the ProLiant Cluster for Entry Level SAN please see the following QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11932_div/11932_div.html (Worldwide) ProLiant Cluster HA/F500 for the Enterprise SAN NOTE: For additional information regarding the ProLiant Cluster HA/F500 for Enterprise SAN please see the following QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11933_div/11933_div.html (Worldwide) HP Serviceguard for Linux ProLiant Cluster A.11.16 for SUSE SLES 9 and Red Hat EL 3 & 4 (2 node license cluster kit) HP Serviceguard for Linux A.11.16 for SUSE SLES9 and Red Hat EL 3 & 4 (single license version) HP Serviceguard for Linux and Red Hat Global File System - 1 year subscription HP Serviceguard for Linux and Red Hat Global File System - 3 years subscription NOTE: For additional information regarding HP Serviceguard for Linux, please see the following QuickSpecs at: http://h18000.www1.hp.com/products/quickspecs/11518_div/11518_div.html (Worldwide)

252663-D71

252663-D72 252663-B31 252663-B21

252663-B24

252663-D73 252663-B32

Page 21

Third Party Rack Kit
Rack Adapter Kit NOTE: This kit allows HP rack servers to fit in racks that are 24" wide. Third Party Rack Kit NOTE: The Third party rack kit supports the HP ProLiant ML530 G2, HP ProLiant ML570 G2, HP ProLiant DL740, and HP ProLiant DL760 G2. Provides support for any rack, square hole or round hole (including HP Rack System /E and HP Systems) with an adjustment range from 23 " 34" deep. NOTE: The Third Party Rack Kit is required for round hole racks or for square hole racks that do not conform to the adjustment range of the standard rail that ships with the server. Telco Rack Support NOTE: Support for all 2-post Telco racks requires the Third Party Rack Kit (PN 274739-B21) kit plus an additional option kit from Rack Solutions. The Rack Solutions brackets can be purchased at: http://www.racksolutions.com/compaq.

332815-B21 274739-B21

HP Rack 5000 Series (Graphite Metallic)
HP 5642 Rack-Unassembled NOTE: Please see the HP Rack 5642 QuickSpecs for additional part numbers and Technical Specifications such as height, width, depth, weight, and color: http://h18000.www1.hp.com/products/quickspecs/12074_div/12074_div.HTML (Worldwide) NOTE: For additional information regarding Rack Cabinets, please see the following URL: http://www.hp.com/go/rackandpower.

358254-B21

HP Rack 10000 G2 Series (Carbon/Graphite Metallic)
10642 G2 (42U) Rack Cabinet - Pallet 10642 G2 (42U) Rack Cabinet - Shock Pallet 10642 G2 (42U) Rack Cabinet - Crated 10642 G2 (42U) Rack Cabinet, with Extension - Shock Pallet 10642 G2 (42U) Rack Cabinet, without door - Shock Pallet 10642 G2 (42U) Rack Cabinet - with Extension, without door - Shock Pallet 10636 G2 (36U) Rack Cabinet - Pallet 10636 G2 (36U) Rack Cabinet - Shock Pallet 10636 G2 (36U) Rack Cabinet - Crated 10636 G2 (36U) Rack Cabinet , with Extension - Shock Pallet 10636 G2 (36U) Rack Cabinet, without door - Shock Pallet 10636 G2 (36U) Rack Cabinet, with Extension, without door - Shock Pallet NOTE: It is mandatory to use a shock pallet when shipping racks with equipment installed. NOTE: Please see the Rack 10000 G2 QuickSpecs for Technical Specifications such as height, width, depth, weight, and color: http://h18000.www1.hp.com/products/quickspecs/12402_div/12402_div.HTML (Worldwide) NOTE: For additional information regarding Rack Cabinets, please see the following URL: http://www.hp.com/go/rackandpower.
AF001A AF002A AF003A AF004A AF005A AF006A AF011A AF012A AF013A AF014A AF015A AF016A

Page 22

HP Rack 10000 Series (Graphite Metallic)
10642 (42U) Infrastructure Rack (Low Voltage) 10642 (42U) Infrastructure Rack (High Voltage) HP Rack S10614 (14U) Rack Cabinet Shock Pallet HP Rack 10842 (42U, 800mm wide) Pallet HP Rack 10842 (42U, 800mm wide) Shock Pallet HP Rack 10647 (47U) Pallet HP Rack 10647 (47U) Crated HP Rack 10642 (42U) Pallet HP Rack 10642 (42U) Shock Pallet HP Rack 10642 (42U) Crated HP Rack 10636 (36U) Pallet HP Rack 10636 (36U) Shock Pallet HP Rack 10636 (36U) Crated HP Rack 10622 (22U) Pallet HP Rack 10622 (22U) Shock Pallet HP Rack 10622 (22U) Crated NOTE: xxxxxx-B21 (pallet) used to ship empty racks shipped on a truck. -B22 (shock pallet) used to ship racks with equipment installed (by custom systems, VARs and Channels). xxxxxx-B23 (crated) used for air shipments of empty racks. NOTE: Please see the Rack 10000 QuickSpecs for Technical Specifications such as height, width, depth, weight, and color: http://h18000.www1.hp.com/products/quickspecs/10995_div/10995_div.HTML (Worldwide) NOTE: For additional information regarding Rack Cabinets, please see the following URL: http://www.hp.com/go/rackandpower.

379006-001 379005-001 292302-B22 257415-B21 257415-B22 245160-B21 245160-B23 245161-B21 245161-B22 245161-B23 245162-B21 245162-B22 245162-B23 245163-B21 245163-B22 245163-B23
Keyboards and Monitors TFT7210R Rack Mounted 17" Monitor NOTE: For a complete list of Monitors please view the following URL: http://www.hp.com/go/kvm. TFT7600RKM US TFT7600RKM UK TFT7600RKM GR TFT7600RKM FR TFT7600RKM IT TFT7600RKM SP TFT7600RKM DEN TFT7600RKM NOR TFT7600RKM SE/FI TFT7600RKM SWI TFT7600RKM PORT TFT7600RKM BEL TFT7600RKM JPN2 TFT7600RKM RUS TFT7600RKM INTL

348373-B21

AG052A AG053A AG054A AG055A AG056A AG057A AG058A AG059A AG060A AG061A AG062A AG063A AG064A AG065A AG066A

Page 23

1U Rack Keyboard & Drawer (Carbon) Country Code Key (for 1U Rack Keyboard & Drawer (PN 257054-xx1)) XX = 001 XX = 031 XX = 041 XX = 051 XX = 061 XX = 071 XX = 081 US UK Germany France Italy Spain Denmark XX = 091 XX = 101 XX = 111 XX = 131 XX = 181 XX = 291 XX = B31 Norway Sweden/Finland Switzerland Portugal Belgium Japan International

257054-xx1

NOTE: For additional information regarding Rack Options, please see the following URL: http://www.hp.com/go/rackandpower.

HP KVM Switch Options

IP Console Switch Box (KVM/IP), 3 x 1 x 16 IP Console Switch Box (KVM/IP), 1 x 1 x 16 Server Console Switch (KVM), 0 x 1 x 8 port Server Console Switch (KVM), 0 x 2 x 16 port PS/2 Interface Adapter, 1 pack PS/2 Interface Adapter, 8 pack USB Interface Adapter, 1 pack Serial Interface adapter - 1 Pack with power supply NOTE: Cat5e cables are required to connect Interface Adapters to Console Switches. Cat5e cables can be found at the following URL: http://www.hp.com/go/kvm. HP 1x 4 USB/PS2 KVM Switch, TT (NA/JPN) HP 1x 4 USB/PS2 KVM Switch, TT (AU/NZ) HP 1x 4 USB/PS2 KVM Switch, TT (UK) HP 1x 4 USB/PS2 KVM Switch, TT (EU) HP 1x 4 USB/PS2 KVM Switch, RM (ALL) HP PS2 KVM Cable with audio, 6', 2-pack HP USB KVM Cable with audio, 6', 2-pack NOTE: For additional information regarding KVM switches, Serial Console servers, rack mount monitors, keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.

U4635E

U4637E

U4636E U4638E

U4625E

Page 25

HP ProLiant DL760 G2 2.2 GHz/2MB or 2.0 GHz/1MB, 2048MB (4P) Standard Memory 2048 MB addressable buffered ECC SDRAM DIMM memory (2 x 256 MB DIMMs x 5 Hot-Plug RAID Memory Cartridges. The 5th cartridge is populated for redundancy.) Standard Memory Plus Optional Memory Up to 51,200 MB of addressable ECC SDRAM DIMM memory is available with the installation of optional ECC SDRAM DIMM memory expansion kits. Standard Memory Replaced with Optional Memory Up to 65,536 MB of addressable ECC SDRAM DIMM memory is available with the removal of standard memory and the installation of optional ECC SDRAM DIMM memory expansion kits. NOTE: 8 slots per Hot-Plug RAID Memory Cartridge. Up to 64 GB addressable memory total. Memory must be added in banks of two DIMMs per cartridge across all five (four if running in a non-redundant mode) Hot-Plug RAID Memory Cartridges. Charts do not represent all possible configurations. Memory Slot Cartridge 1 (C1) Cartridge 2 (C2) Cartridge 3 (C3) Cartridge 4 (C4) Cartridge 5 (C5) Standard Optional Maximum Standard Optional Maximum Standard Optional Maximum Standard Optional Maximum Standard Optional Maximum 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB 256 MB 256 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB empty 2048 MB 2048 MB
Following are memory options available from HP: 2048 MB 133MHz ECC SDRAM Memory Option Kit (1 x 2048 MB) NOTE: A ROM dated later than 2/14/2003 is needed to use 2 GB DIMMs. 1024 MB 133MHz ECC SDRAM Memory Option Kit (1 x 1024 MB) 512 MB 133MHz ECC SDRAM Memory Option Kit (1 x 512 MB) 256 MB 133MHz ECC SDRAM Memory Option Kit (1 x 256 MB)

Maximum Storage Capacity - (SCSI Attached) Internal 1.20TB (4 x 300 GB Ultra320) External 184.8TB hot plug SCSI storage (44 x (14 x 300 B Ultra320)) Total 186.0TB
Tape Drives, Tape Autoloaders, & Tape Libraries

Page 29

NOTE: For an up-to-date listing of the latest O/S Support details for each of the Tape Drives listed below, please see the following: http://h18000.www1.hp.com/products/quickspecs/Division/10233.html (Worldwide) NOTE: For an up-to-date listing of the latest O/S Support details for each of the Tape Autoloaders & Tape Libraries listed below, please see the following: http://h18000.www1.hp.com/products/quickspecs/Division/10809.html (Worldwide) NOTE: For complete listing of tape drive offerings see http://www.hp.com/products1/storage/compatibility/tapebackup/ISS/index.html For details on connecting tape drives to this server, see the following: Quantity Position Supported Supported Controller 1 0-3 Smart Array 5i Controller (integrated on system board) HP StorageWorks Tape 64-Bit/133MHz Dual Channel Ultra320 SCSI Adapter Drives, Hot Plug DAT 24 USB 64-Bit/133-MHz Single Channel Ultra320 SCSI HBA G2 DAT 40 USB 64-Bit/66-MHz Dual Channel Wide Ultra3 SCSI Adapter, Alternate DAT 72 USB OS HP StorageWorks Tape Drives, USB External DAT 40 USB DAT 72 USB HP StorageWorks Tape Drives, External Ultrium 232 Ultrium 448 Ultrium 460 DAT 40 DAT 72 DLT VS80 DLT VS160 SDLT 320 HP StorageWorks Tape Drives, External Ultrium 960 SDLT 600 HP StorageWorks Autoloaders, External DAT 72x6 Tape Autoloader 1/8 Tape Autoloader 1 per USB port External USB port

Up to 2

64-Bit/133MHz Dual Channel Ultra320 SCSI Adapter 64-Bit/133-MHz Single Channel Ultra320 SCSI HBA G2 64-Bit/66-MHz Dual Channel Wide Ultra3 SCSI Adapter, Alternate OS

1 per SCSI Channel

64-Bit/133MHz Dual Channel Ultra320 SCSI Adapter 64-Bit/133-MHz Single Channel Ultra320 SCSI HBA G2 64-Bit/66-MHz Dual Channel Wide Ultra3 SCSI Adapter, Alternate OS 64-Bit/133MHz Dual Channel Ultra320 SCSI Adapter 64-Bit/133-MHz Single Channel Ultra320 SCSI HBA G2 64-Bit/66-MHz Dual Channel Wide Ultra3 SCSI Adapter, Alternate OS
1 autoloader per SCSI channel

Page 30

HP StorageWorks Rackmount Tape Drive Enclosures 1U Rack-Mount Kit 3U Rack-Mount Kit 5U Rack-Mount Kit 1 per SCSI channel External
HP StorageWorks Tape Please reference the MSL Tape Libraries, External MSL2024 (Ultrium 448 Library and 960-based) QuickSpecs to MSL4048 (Ultrium 448 determine and 960-based) configuration MSL6000 (Ultrium 960 requirements and 460-based) MSL6000 (SDLT 600based) MSL5026S2 (SDLT 320based) MSL5052S2 (SDLT 320based)
Please consult the EBS connectivity matrix at http://www.hp.com/go/ebs for detailed connectivity information.

Page 31

Technical Specifications

Slimline CD/ Shipping Dimensions DVD-ROM Combo Drive Shipping Weight (8X/24X) Disk
13.88 x 11.38 x 9.25 in (35.26 x 28.91 x 23.50 cm) 5 lb (2.27 kg) Applicable Disk DVD-R (Read Only) 2.6 GB/side DVD-RAM (Read Only) 5.2 GB/side DVD-RAM (Read Only) CD-ROM Mode-1 data disc CD-ROM Mode-2 data disc CD Audio disc CD-Extra CD-ROM CD-R CD Text PhotoCD CD-I (mode 2) CD-I Ready CD-Bridge

Page 33

Capacity

DVD-ROM

Block Size
Diameter Loading Mechanism Interface Access Times (typical) Audio Output Level (typical) Data Transfer Rate Tray type EIDE (ATAPI) Random Full-Stroke Line-out
4.7 GB/side 8.5 GB/side 9.40 GB/side DVD-R 3.95 GB/side DVD-RAM 2.6 GB/side and 5.2 GB/ CD-ROM Mode-MB (550 MB) Mode-MB (640 MB) DVD 2,048 bytes CD 2,352 (Mode0) 2352, 2340, 2336, 2048 bytes (Mode-1) 2352, 2340, 2336, 2048 bytes (Mode-2) 120 mm, 80 mm (with adapter at vertical mounting mode)
DVD-SL DVD-DL Double Sided
DVD-ROM < 120 ms, CD-ROM < 110 ms DVD-ROM < 240 ms, CD-ROM < 160 ms CD 0.7 Vrms at 47 Kohms Load
Cache Buffer Spin-up Time (typical) MTBF Ambient Temperature Relative Humidity
Dimensions Option Kit Contents
DVD-ROM Single Layer 10.8 MB/sec. Max. DVD-RAM 2.77 MB/sec. Maxz CD-ROM 7.2 MB/sec. Max. 2 MB less than 10 seconds 120,000 Power On Hours (POH) Operating -22 to 140 F (-30 to 60 C) Operating 10% to 80% Storage/ 5% to 95% Transportation (HxWxD, maximum) 0.5 x 5.04 x 5.1 in (12.7x128x129.4 mm) DVD-ROM drive with installation guide, warranty card, registration card

Page 34

Smart Array 5i Controller Protocol (integrated on system Processor board) XOR engine Electrical interface Simultaneous Drive Transfer Channels Channel Transfer Rate SCSI Port Connectors Memory
Wide Ultra3 SCSI 32-bit RISC Hardware RAID Low Voltage Differential (LVD) 2
320 MB/s total; 160 MB/s per channel One external and one internal SCSI port 32 MB of DRAM used for code, transfer buffers, and non-battery-backed read cache 160 MB/s Peak transfer rate Logical Drives Supported 32 Yes Software Upgradeable Firmware RAID 5 (Distributed Data Guarding RAID Support RAID 1+0 (Striping and Mirroring) RAID 1 (Mirroring) RAID 0 (Stripping) Disk Drive and Enclosure Ultra2 and Ultra3 Protocol Support

NC7170 Dual-Port PCI-X Network Interface 1000T Gigabit Server Compatibility Adapter
Data Transfer Method Network Transfer Rate

Connector Cable Support

Two 10/100/1000-T ports IEEE 802.3 10Base-T IEEE 802.3ab 1000Base-T IEEE 802.3u 100Base-TX IEEE 802.3ad, IEEE 802.3p, and IEEE 802.3Q 64-bit/133MHz PCI-X, compatible with 64/100, 64/66, 64/33 and 32/33 10Base-T (Half-Duplex) 10 Mb/s 10Base-T (Full-Duplex) 20 Mb/s 100Base-TX (Half-Duplex) 100 Mb/s 100Base-TX (Full-Duplex) 200 Mb/s 1000Base-T (Half and Full-Duplex) 2000 Mb/s Two RJ-45 10Base-T Category 3,4 or 5 UTP; up to 328 ft (100 m) 10/100/1000Base-T Category 5 UTP (2 pair); up to 328 ft (100 m)

Page 35

Copyright 2006 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation. Intel is a US registered trademark of Intel Corporation. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. For hard drives, 1 GB = 1 billion bytes. Actual formatted capacity is less.

Page 36